2 * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
3 * Copyright 2013 Aaro Koskinen <aaro.koskinen@iki.fi>
5 * This program is free software; you can redistribute it and/or modify
6 * it under the terms of the GNU General Public License version 2 (or later) as
7 * published by the Free Software Foundation.
12 #include "omap34xx.dtsi"
16 compatible = "nokia,omap3-n900", "ti,omap3";
25 device_type = "memory";
26 reg = <0x80000000 0x10000000>; /* 256 MB */
30 compatible = "gpio-keys";
33 label = "Camera Lens Cover";
34 gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
35 linux,input-type = <5>; /* EV_SW */
36 linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
41 label = "Camera Focus";
42 gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
43 linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
48 label = "Camera Capture";
49 gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
50 linux,code = <0xd4>; /* KEY_CAMERA */
55 label = "Lock Button";
56 gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
57 linux,code = <0x98>; /* KEY_SCREENLOCK */
62 label = "Keypad Slide";
63 gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
64 linux,input-type = <5>; /* EV_SW */
65 linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
70 label = "Proximity Sensor";
71 gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
72 linux,input-type = <5>; /* EV_SW */
73 linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
80 pinctrl-names = "default";
82 uart2_pins: pinmux_uart2_pins {
83 pinctrl-single,pins = <
84 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx */
85 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
89 uart3_pins: pinmux_uart3_pins {
90 pinctrl-single,pins = <
91 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx */
92 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
96 i2c1_pins: pinmux_i2c1_pins {
97 pinctrl-single,pins = <
98 0x18a (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
99 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
103 i2c2_pins: pinmux_i2c2_pins {
104 pinctrl-single,pins = <
105 0x18e (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
106 0x190 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
110 i2c3_pins: pinmux_i2c3_pins {
111 pinctrl-single,pins = <
112 0x192 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
113 0x194 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
117 mmc1_pins: pinmux_mmc1_pins {
118 pinctrl-single,pins = <
119 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
120 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
121 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
122 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
123 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
124 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
128 display_pins: pinmux_display_pins {
129 pinctrl-single,pins = <
130 0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
136 pinctrl-names = "default";
137 pinctrl-0 = <&i2c1_pins>;
139 clock-frequency = <2200000>;
143 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
144 interrupt-parent = <&intc>;
148 #include "twl4030.dtsi"
149 #include "twl4030_omap3.dtsi"
152 regulator-name = "V28";
153 regulator-min-microvolt = <2800000>;
154 regulator-max-microvolt = <2800000>;
155 regulator-always-on; /* due battery cover sensor */
159 regulator-name = "VCSI";
160 regulator-min-microvolt = <1800000>;
161 regulator-max-microvolt = <1800000>;
165 regulator-name = "VMMC2_30";
166 regulator-min-microvolt = <2800000>;
167 regulator-max-microvolt = <3000000>;
171 regulator-name = "VCAM_ANA_28";
172 regulator-min-microvolt = <2800000>;
173 regulator-max-microvolt = <2800000>;
177 regulator-name = "VMMC1";
178 regulator-min-microvolt = <1850000>;
179 regulator-max-microvolt = <3150000>;
183 regulator-name = "V28_A";
184 regulator-min-microvolt = <2800000>;
185 regulator-max-microvolt = <3000000>;
186 regulator-always-on; /* due VIO leak to AIC34 VDDs */
190 regulator-name = "VPLL";
191 regulator-min-microvolt = <1800000>;
192 regulator-max-microvolt = <1800000>;
197 regulator-name = "VSDI_CSI";
198 regulator-min-microvolt = <1800000>;
199 regulator-max-microvolt = <1800000>;
204 regulator-name = "VMMC2_IO_18";
205 regulator-min-microvolt = <1800000>;
206 regulator-max-microvolt = <1800000>;
210 regulator-name = "VIO";
211 regulator-min-microvolt = <1800000>;
212 regulator-max-microvolt = <1800000>;
217 regulator-name = "VINTANA1";
218 /* fixed to 1500000 */
223 regulator-name = "VINTANA2";
224 regulator-min-microvolt = <2750000>;
225 regulator-max-microvolt = <2750000>;
230 regulator-name = "VINTDIG";
231 /* fixed to 1500000 */
237 compatible = "ti,twl4030-audio";
238 ti,enable-vibra = <1>;
244 ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
248 pinctrl-names = "default";
249 pinctrl-0 = <&i2c2_pins>;
251 clock-frequency = <100000>;
253 tlv320aic3x: tlv320aic3x@18 {
254 compatible = "ti,tlv320aic3x";
256 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
258 0 /* AIC3X_GPIO1_FUNC_DISABLED */
259 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
262 AVDD-supply = <&vmmc2>;
263 DRVDD-supply = <&vmmc2>;
264 IOVDD-supply = <&vio>;
265 DVDD-supply = <&vio>;
268 tlv320aic3x_aux: tlv320aic3x@19 {
269 compatible = "ti,tlv320aic3x";
271 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
273 AVDD-supply = <&vmmc2>;
274 DRVDD-supply = <&vmmc2>;
275 IOVDD-supply = <&vio>;
276 DVDD-supply = <&vio>;
280 compatible = "national,lp5523";
282 clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
283 enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
286 chan-name = "lp5523:kb1";
287 led-cur = /bits/ 8 <50>;
288 max-cur = /bits/ 8 <100>;
292 chan-name = "lp5523:kb2";
293 led-cur = /bits/ 8 <50>;
294 max-cur = /bits/ 8 <100>;
298 chan-name = "lp5523:kb3";
299 led-cur = /bits/ 8 <50>;
300 max-cur = /bits/ 8 <100>;
304 chan-name = "lp5523:kb4";
305 led-cur = /bits/ 8 <50>;
306 max-cur = /bits/ 8 <100>;
310 chan-name = "lp5523:b";
311 led-cur = /bits/ 8 <50>;
312 max-cur = /bits/ 8 <100>;
316 chan-name = "lp5523:g";
317 led-cur = /bits/ 8 <50>;
318 max-cur = /bits/ 8 <100>;
322 chan-name = "lp5523:r";
323 led-cur = /bits/ 8 <50>;
324 max-cur = /bits/ 8 <100>;
328 chan-name = "lp5523:kb5";
329 led-cur = /bits/ 8 <50>;
330 max-cur = /bits/ 8 <100>;
334 chan-name = "lp5523:kb6";
335 led-cur = /bits/ 8 <50>;
336 max-cur = /bits/ 8 <100>;
340 bq27200: bq27200@55 {
341 compatible = "ti,bq27200";
347 pinctrl-names = "default";
348 pinctrl-0 = <&i2c3_pins>;
350 clock-frequency = <400000>;
354 pinctrl-names = "default";
355 pinctrl-0 = <&mmc1_pins>;
356 vmmc-supply = <&vmmc1>;
358 cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
370 ranges = <0 0 0x04000000 0x10000000>; /* 256MB */
372 /* gpio-irq for dma: 65 */
375 #address-cells = <1>;
377 reg = <0 0 0x10000000>;
381 gpmc,burst-length = <16>;
385 gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
386 gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
388 gpmc,cs-rd-off-ns = <87>;
389 gpmc,cs-wr-off-ns = <87>;
390 gpmc,adv-on-ns = <0>;
391 gpmc,adv-rd-off-ns = <10>;
392 gpmc,adv-wr-off-ns = <10>;
393 gpmc,oe-on-ns = <15>;
394 gpmc,oe-off-ns = <87>;
396 gpmc,we-off-ns = <87>;
397 gpmc,rd-cycle-ns = <112>;
398 gpmc,wr-cycle-ns = <112>;
399 gpmc,access-ns = <81>;
400 gpmc,page-burst-access-ns = <15>;
401 gpmc,bus-turnaround-ns = <0>;
402 gpmc,cycle2cycle-delay-ns = <0>;
403 gpmc,wait-monitoring-ns = <0>;
404 gpmc,clk-activation-ns = <5>;
405 gpmc,wr-data-mux-bus-ns = <30>;
406 gpmc,wr-access-ns = <81>;
407 gpmc,sync-clk-ps = <15000>;
410 * MTD partition table corresponding to Nokia's
411 * Maemo 5 (Fremantle) release.
414 label = "bootloader";
415 reg = <0x00000000 0x00020000>;
420 reg = <0x00020000 0x00060000>;
424 reg = <0x00080000 0x00040000>;
428 reg = <0x000c0000 0x00200000>;
432 reg = <0x002c0000 0x00200000>;
436 reg = <0x004c0000 0x0fb40000>;
443 * For some reason, touchscreen is necessary for screen to work at
444 * all on real hw. It works well without it on emulator.
446 * Also... order in the device tree actually matters here.
449 compatible = "tsc2005";
450 spi-max-frequency = <6000000>;
454 compatible = "acx565akm";
455 spi-max-frequency = <6000000>;
458 pinctrl-names = "default";
459 pinctrl-0 = <&display_pins>;
464 interface-type = <0>;
465 usb-phy = <&usb2_phy>;
467 phy-names = "usb2-phy";
477 pinctrl-names = "default";
478 pinctrl-0 = <&uart2_pins>;
482 pinctrl-names = "default";
483 pinctrl-0 = <&uart3_pins>;