drivers/leds/Kconfig

   1 config LEDS_GPIO_REGISTER
   2         bool
   3         help
   4           This option provides the function gpio_led_register_device.
   5           As this function is used by arch code it must not be compiled as a
   6           module.
   7
   8 menuconfig NEW_LEDS
   9         bool "LED Support"
  10         help
  11           Say Y to enable Linux LED support.  This allows control of supported
  12           LEDs from both userspace and optionally, by kernel events (triggers).
  13
  14 if NEW_LEDS
  15
  16 config LEDS_CLASS
  17         tristate "LED Class Support"
  18         help
  19           This option enables the led sysfs class in /sys/class/leds.  You'll
  20           need this to do anything useful with LEDs.  If unsure, say N.
  21
  22 config LEDS_CLASS_FLASH
  23         tristate "LED Flash Class Support"
  24         depends on LEDS_CLASS
  25         help
  26           This option enables the flash led sysfs class in /sys/class/leds.
  27           It wrapps LED Class and adds flash LEDs specific sysfs attributes
  28           and kernel internal API to it. You'll need this to provide support
  29           for the flash related features of a LED device. It can be built
  30           as a module.
  31
  32 config LEDS_BRIGHTNESS_HW_CHANGED
  33         bool "LED Class brightness_hw_changed attribute support"
  34         depends on LEDS_CLASS
  35         help
  36           This option enables support for the brightness_hw_changed attribute
  37           for led sysfs class devices under /sys/class/leds.
  38
  39           See Documentation/ABI/testing/sysfs-class-led for details.
  40
  41 comment "LED drivers"
  42
  43 config LEDS_88PM860X
  44         tristate "LED Support for Marvell 88PM860x PMIC"
  45         depends on LEDS_CLASS
  46         depends on MFD_88PM860X
  47         help
  48           This option enables support for on-chip LED drivers found on Marvell
  49           Semiconductor 88PM8606 PMIC.
  50
  51 config LEDS_AAT1290
  52         tristate "LED support for the AAT1290"
  53         depends on LEDS_CLASS_FLASH
  54         depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
  55         depends on GPIOLIB || COMPILE_TEST
  56         depends on OF
  57         depends on PINCTRL
  58         help
  59          This option enables support for the LEDs on the AAT1290.
  60
  61 config LEDS_BCM6328
  62         tristate "LED Support for Broadcom BCM6328"
  63         depends on LEDS_CLASS
  64         depends on HAS_IOMEM
  65         depends on OF
  66         help
  67           This option enables support for LEDs connected to the BCM6328
  68           LED HW controller accessed via MMIO registers.
  69
  70 config LEDS_BCM6358
  71         tristate "LED Support for Broadcom BCM6358"
  72         depends on LEDS_CLASS
  73         depends on HAS_IOMEM
  74         depends on OF
  75         help
  76           This option enables support for LEDs connected to the BCM6358
  77           LED HW controller accessed via MMIO registers.
  78
  79 config LEDS_CPCAP
  80         tristate "LED Support for Motorola CPCAP"
  81         depends on LEDS_CLASS
  82         depends on MFD_CPCAP
  83         depends on OF
  84         help
  85           This option enables support for LEDs offered by Motorola's
  86           CPCAP PMIC.
  87
  88 config LEDS_LM3530
  89         tristate "LCD Backlight driver for LM3530"
  90         depends on LEDS_CLASS
  91         depends on I2C
  92         help
  93           This option enables support for the LCD backlight using
  94           LM3530 ambient light sensor chip. This ALS chip can be
  95           controlled manually or using PWM input or using ambient
  96           light automatically.
  97
  98 config LEDS_LM3533
  99         tristate "LED support for LM3533"
 100         depends on LEDS_CLASS
 101         depends on MFD_LM3533
 102         help
 103           This option enables support for the LEDs on National Semiconductor /
 104           TI LM3533 Lighting Power chips.
 105
 106           The LEDs can be controlled directly, through PWM input, or by the
 107           ambient-light-sensor interface. The chip supports
 108           hardware-accelerated blinking with maximum on and off periods of 9.8
 109           and 77 seconds respectively.
 110
 111 config LEDS_LM3642
 112         tristate "LED support for LM3642 Chip"
 113         depends on LEDS_CLASS && I2C
 114         select REGMAP_I2C
 115         help
 116           This option enables support for LEDs connected to LM3642.
 117           The LM3642 is a 4MHz fixed-frequency synchronous boost
 118           converter plus 1.5A constant current driver for a high-current
 119           white LED.
 120
 121
 122 config LEDS_LOCOMO
 123         tristate "LED Support for Locomo device"
 124         depends on LEDS_CLASS
 125         depends on SHARP_LOCOMO
 126         help
 127           This option enables support for the LEDs on Sharp Locomo.
 128           Zaurus models SL-5500 and SL-5600.
 129
 130 config LEDS_MIKROTIK_RB532
 131         tristate "LED Support for Mikrotik Routerboard 532"
 132         depends on LEDS_CLASS
 133         depends on MIKROTIK_RB532
 134         help
 135           This option enables support for the so called "User LED" of
 136           Mikrotik's Routerboard 532.
 137
 138 config LEDS_MT6323
 139         tristate "LED Support for Mediatek MT6323 PMIC"
 140         depends on LEDS_CLASS
 141         depends on MFD_MT6397
 142         help
 143           This option enables support for on-chip LED drivers found on
 144           Mediatek MT6323 PMIC.
 145
 146 config LEDS_S3C24XX
 147         tristate "LED Support for Samsung S3C24XX GPIO LEDs"
 148         depends on LEDS_CLASS
 149         depends on ARCH_S3C24XX
 150         help
 151           This option enables support for LEDs connected to GPIO lines
 152           on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440.
 153
 154 config LEDS_NET48XX
 155         tristate "LED Support for Soekris net48xx series Error LED"
 156         depends on LEDS_CLASS
 157         depends on SCx200_GPIO
 158         help
 159           This option enables support for the Soekris net4801 and net4826 error
 160           LED.
 161
 162 config LEDS_FSG
 163         tristate "LED Support for the Freecom FSG-3"
 164         depends on LEDS_CLASS
 165         depends on MACH_FSG
 166         help
 167           This option enables support for the LEDs on the Freecom FSG-3.
 168
 169 config LEDS_WRAP
 170         tristate "LED Support for the WRAP series LEDs"
 171         depends on LEDS_CLASS
 172         depends on SCx200_GPIO
 173         help
 174           This option enables support for the PCEngines WRAP programmable LEDs.
 175
 176 config LEDS_COBALT_QUBE
 177         tristate "LED Support for the Cobalt Qube series front LED"
 178         depends on LEDS_CLASS
 179         depends on MIPS_COBALT
 180         help
 181           This option enables support for the front LED on Cobalt Qube series
 182
 183 config LEDS_COBALT_RAQ
 184         bool "LED Support for the Cobalt Raq series"
 185         depends on LEDS_CLASS=y && MIPS_COBALT
 186         select LEDS_TRIGGERS
 187         help
 188           This option enables support for the Cobalt Raq series LEDs.
 189
 190 config LEDS_SUNFIRE
 191         tristate "LED support for SunFire servers."
 192         depends on LEDS_CLASS
 193         depends on SPARC64
 194         select LEDS_TRIGGERS
 195         help
 196           This option enables support for the Left, Middle, and Right
 197           LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
 198
 199 config LEDS_IPAQ_MICRO
 200         tristate "LED Support for the Compaq iPAQ h3xxx"
 201         depends on LEDS_CLASS
 202         depends on MFD_IPAQ_MICRO
 203         help
 204           Choose this option if you want to use the notification LED on
 205           Compaq/HP iPAQ h3100 and h3600.
 206
 207 config LEDS_HP6XX
 208         tristate "LED Support for the HP Jornada 6xx"
 209         depends on LEDS_CLASS
 210         depends on SH_HP6XX
 211         help
 212           This option enables LED support for the handheld
 213           HP Jornada 620/660/680/690.
 214
 215 config LEDS_PCA9532
 216         tristate "LED driver for PCA9532 dimmer"
 217         depends on LEDS_CLASS
 218         depends on I2C && INPUT
 219         help
 220           This option enables support for NXP pca9532
 221           LED controller. It is generally only useful
 222           as a platform driver
 223
 224 config LEDS_PCA9532_GPIO
 225         bool "Enable GPIO support for PCA9532"
 226         depends on LEDS_PCA9532
 227         depends on GPIOLIB
 228         help
 229           Allow unused pins on PCA9532 to be used as gpio.
 230
 231           To use a pin as gpio pca9532_type in pca9532_platform data needs to
 232           set to PCA9532_TYPE_GPIO.
 233
 234 config LEDS_GPIO
 235         tristate "LED Support for GPIO connected LEDs"
 236         depends on LEDS_CLASS
 237         depends on GPIOLIB || COMPILE_TEST
 238         help
 239           This option enables support for the LEDs connected to GPIO
 240           outputs. To be useful the particular board must have LEDs
 241           and they must be connected to the GPIO lines.  The LEDs must be
 242           defined as platform devices and/or OpenFirmware platform devices.
 243           The code to use these bindings can be selected below.
 244
 245 config LEDS_LP3944
 246         tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip"
 247         depends on LEDS_CLASS
 248         depends on I2C
 249         help
 250           This option enables support for LEDs connected to the National
 251           Semiconductor LP3944 Lighting Management Unit (LMU) also known as
 252           Fun Light Chip.
 253
 254           To compile this driver as a module, choose M here: the
 255           module will be called leds-lp3944.
 256
 257 config LEDS_LP3952
 258         tristate "LED Support for TI LP3952 2 channel LED driver"
 259         depends on LEDS_CLASS
 260         depends on I2C
 261         depends on GPIOLIB
 262         select REGMAP_I2C
 263         help
 264           This option enables support for LEDs connected to the Texas
 265           Instruments LP3952 LED driver.
 266
 267           To compile this driver as a module, choose M here: the
 268           module will be called leds-lp3952.
 269
 270 config LEDS_LP55XX_COMMON
 271         tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501"
 272         depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501
 273         select FW_LOADER
 274         help
 275           This option supports common operations for LP5521/5523/55231/5562/8501
 276           devices.
 277
 278 config LEDS_LP5521
 279         tristate "LED Support for N.S. LP5521 LED driver chip"
 280         depends on LEDS_CLASS && I2C
 281         select LEDS_LP55XX_COMMON
 282         help
 283           If you say yes here you get support for the National Semiconductor
 284           LP5521 LED driver. It is 3 channel chip with programmable engines.
 285           Driver provides direct control via LED class and interface for
 286           programming the engines.
 287
 288 config LEDS_LP5523
 289         tristate "LED Support for TI/National LP5523/55231 LED driver chip"
 290         depends on LEDS_CLASS && I2C
 291         select LEDS_LP55XX_COMMON
 292         help
 293           If you say yes here you get support for TI/National Semiconductor
 294           LP5523/55231 LED driver.
 295           It is 9 channel chip with programmable engines.
 296           Driver provides direct control via LED class and interface for
 297           programming the engines.
 298
 299 config LEDS_LP5562
 300         tristate "LED Support for TI LP5562 LED driver chip"
 301         depends on LEDS_CLASS && I2C
 302         select LEDS_LP55XX_COMMON
 303         help
 304           If you say yes here you get support for TI LP5562 LED driver.
 305           It is 4 channels chip with programmable engines.
 306           Driver provides direct control via LED class and interface for
 307           programming the engines.
 308
 309 config LEDS_LP8501
 310         tristate "LED Support for TI LP8501 LED driver chip"
 311         depends on LEDS_CLASS && I2C
 312         select LEDS_LP55XX_COMMON
 313         help
 314           If you say yes here you get support for TI LP8501 LED driver.
 315           It is 9 channel chip with programmable engines.
 316           Driver provides direct control via LED class and interface for
 317           programming the engines.
 318           It is similar as LP5523, but output power selection is available.
 319           And register layout and engine program schemes are different.
 320
 321 config LEDS_LP8788
 322         tristate "LED support for the TI LP8788 PMIC"
 323         depends on LEDS_CLASS
 324         depends on MFD_LP8788
 325         help
 326           This option enables support for the Keyboard LEDs on the LP8788 PMIC.
 327
 328 config LEDS_LP8860
 329         tristate "LED support for the TI LP8860 4 channel LED driver"
 330         depends on LEDS_CLASS && I2C
 331         select REGMAP_I2C
 332         help
 333           If you say yes here you get support for the TI LP8860 4 channel
 334           LED driver.
 335           This option enables support for the display cluster LEDs
 336           on the LP8860 4 channel LED driver using the I2C communication
 337           bus.
 338
 339 config LEDS_CLEVO_MAIL
 340         tristate "Mail LED on Clevo notebook"
 341         depends on LEDS_CLASS
 342         depends on X86 && SERIO_I8042 && DMI
 343         help
 344           This driver makes the mail LED accessible from userspace
 345           programs through the leds subsystem. This LED have three
 346           known mode: off, blink at 0.5Hz and blink at 1Hz.
 347
 348           The driver supports two kinds of interface: using ledtrig-timer
 349           or through /sys/class/leds/clevo::mail/brightness. As this LED
 350           cannot change it's brightness it blinks instead. The brightness
 351           value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
 352           blink at 1Hz.
 353
 354           This module can drive the mail LED for the following notebooks:
 355
 356                 Clevo D400P
 357                 Clevo D410J
 358                 Clevo D410V
 359                 Clevo D400V/D470V (not tested, but might work)
 360                 Clevo M540N
 361                 Clevo M5x0N (not tested, but might work)
 362                 Positivo Mobile (Clevo M5x0V)
 363
 364           If your model is not listed here you can try the "nodetect"
 365           module parameter.
 366
 367           To compile this driver as a module, choose M here: the
 368           module will be called leds-clevo-mail.
 369
 370 config LEDS_PCA955X
 371         tristate "LED Support for PCA955x I2C chips"
 372         depends on LEDS_CLASS
 373         depends on I2C
 374         help
 375           This option enables support for LEDs connected to PCA955x
 376           LED driver chips accessed via the I2C bus.  Supported
 377           devices include PCA9550, PCA9551, PCA9552, and PCA9553.
 378
 379 config LEDS_PCA963X
 380         tristate "LED support for PCA963x I2C chip"
 381         depends on LEDS_CLASS
 382         depends on I2C
 383         help
 384           This option enables support for LEDs connected to the PCA963x
 385           LED driver chip accessed via the I2C bus. Supported
 386           devices include PCA9633 and PCA9634
 387
 388 config LEDS_WM831X_STATUS
 389         tristate "LED support for status LEDs on WM831x PMICs"
 390         depends on LEDS_CLASS
 391         depends on MFD_WM831X
 392         help
 393           This option enables support for the status LEDs of the WM831x
 394           series of PMICs.
 395
 396 config LEDS_WM8350
 397         tristate "LED Support for WM8350 AudioPlus PMIC"
 398         depends on LEDS_CLASS
 399         depends on MFD_WM8350
 400         help
 401           This option enables support for LEDs driven by the Wolfson
 402           Microelectronics WM8350 AudioPlus PMIC.
 403
 404 config LEDS_DA903X
 405         tristate "LED Support for DA9030/DA9034 PMIC"
 406         depends on LEDS_CLASS
 407         depends on PMIC_DA903X
 408         help
 409           This option enables support for on-chip LED drivers found
 410           on Dialog Semiconductor DA9030/DA9034 PMICs.
 411
 412 config LEDS_DA9052
 413         tristate "Dialog DA9052/DA9053 LEDS"
 414         depends on LEDS_CLASS
 415         depends on PMIC_DA9052
 416         help
 417           This option enables support for on-chip LED drivers found
 418           on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
 419
 420 config LEDS_DAC124S085
 421         tristate "LED Support for DAC124S085 SPI DAC"
 422         depends on LEDS_CLASS
 423         depends on SPI
 424         help
 425           This option enables support for DAC124S085 SPI DAC from NatSemi,
 426           which can be used to control up to four LEDs.
 427
 428 config LEDS_PWM
 429         tristate "PWM driven LED Support"
 430         depends on LEDS_CLASS
 431         depends on PWM
 432         help
 433           This option enables support for pwm driven LEDs
 434
 435 config LEDS_REGULATOR
 436         tristate "REGULATOR driven LED support"
 437         depends on LEDS_CLASS
 438         depends on REGULATOR
 439         help
 440           This option enables support for regulator driven LEDs.
 441
 442 config LEDS_BD2802
 443         tristate "LED driver for BD2802 RGB LED"
 444         depends on LEDS_CLASS
 445         depends on I2C
 446         help
 447           This option enables support for BD2802GU RGB LED driver chips
 448           accessed via the I2C bus.
 449
 450 config LEDS_INTEL_SS4200
 451         tristate "LED driver for Intel NAS SS4200 series"
 452         depends on LEDS_CLASS
 453         depends on PCI && DMI
 454         depends on X86
 455         help
 456           This option enables support for the Intel SS4200 series of
 457           Network Attached Storage servers. You may control the hard
 458           drive or power LEDs on the front panel. Using this driver
 459           can stop the front LED from blinking after startup.
 460
 461 config LEDS_LT3593
 462         tristate "LED driver for LT3593 controllers"
 463         depends on LEDS_CLASS
 464         depends on GPIOLIB || COMPILE_TEST
 465         help
 466           This option enables support for LEDs driven by a Linear Technology
 467           LT3593 controller. This controller uses a special one-wire pulse
 468           coding protocol to set the brightness.
 469
 470 config LEDS_ADP5520
 471         tristate "LED Support for ADP5520/ADP5501 PMIC"
 472         depends on LEDS_CLASS
 473         depends on PMIC_ADP5520
 474         help
 475           This option enables support for on-chip LED drivers found
 476           on Analog Devices ADP5520/ADP5501 PMICs.
 477
 478           To compile this driver as a module, choose M here: the module will
 479           be called leds-adp5520.
 480
 481 config LEDS_MC13783
 482         tristate "LED Support for MC13XXX PMIC"
 483         depends on LEDS_CLASS
 484         depends on MFD_MC13XXX
 485         help
 486           This option enable support for on-chip LED drivers found
 487           on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC.
 488
 489 config LEDS_NS2
 490         tristate "LED support for Network Space v2 GPIO LEDs"
 491         depends on LEDS_CLASS
 492         depends on MACH_KIRKWOOD || MACH_ARMADA_370
 493         default y
 494         help
 495           This option enables support for the dual-GPIO LEDs found on the
 496           following LaCie/Seagate boards:
 497
 498                 Network Space v2 (and parents: Max, Mini)
 499                 Internet Space v2
 500                 d2 Network v2
 501                 n090401 (Seagate NAS 4-Bay)
 502
 503 config LEDS_NETXBIG
 504         tristate "LED support for Big Network series LEDs"
 505         depends on LEDS_CLASS
 506         depends on MACH_KIRKWOOD
 507         default y
 508         help
 509           This option enable support for LEDs found on the LaCie 2Big
 510           and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
 511           controlled through a GPIO extension bus.
 512
 513 config LEDS_ASIC3
 514         bool "LED support for the HTC ASIC3"
 515         depends on LEDS_CLASS=y
 516         depends on MFD_ASIC3
 517         default y
 518         help
 519           This option enables support for the LEDs on the HTC ASIC3. The HTC
 520           ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver
 521           cannot be used. This driver supports hardware blinking with an on+off
 522           period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700.
 523
 524 config LEDS_TCA6507
 525         tristate "LED Support for TCA6507 I2C chip"
 526         depends on LEDS_CLASS && I2C
 527         help
 528           This option enables support for LEDs connected to TC6507
 529           LED driver chips accessed via the I2C bus.
 530           Driver support brightness control and hardware-assisted blinking.
 531
 532 config LEDS_TLC591XX
 533         tristate "LED driver for TLC59108 and TLC59116 controllers"
 534         depends on LEDS_CLASS && I2C
 535         select REGMAP_I2C
 536         help
 537           This option enables support for Texas Instruments TLC59108
 538           and TLC59116 LED controllers.
 539
 540 config LEDS_MAX77693
 541         tristate "LED support for MAX77693 Flash"
 542         depends on LEDS_CLASS_FLASH
 543         depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS
 544         depends on MFD_MAX77693
 545         depends on OF
 546         help
 547           This option enables support for the flash part of the MAX77693
 548           multifunction device. It has build in control for two leds in flash
 549           and torch mode.
 550
 551 config LEDS_MAX8997
 552         tristate "LED support for MAX8997 PMIC"
 553         depends on LEDS_CLASS && MFD_MAX8997
 554         help
 555           This option enables support for on-chip LED drivers on
 556           MAXIM MAX8997 PMIC.
 557
 558 config LEDS_LM355x
 559         tristate "LED support for LM355x Chips, LM3554 and LM3556"
 560         depends on LEDS_CLASS && I2C
 561         select REGMAP_I2C
 562         help
 563           This option enables support for LEDs connected to LM355x.
 564           LM355x includes Torch, Flash and Indicator functions.
 565
 566 config LEDS_OT200
 567         tristate "LED support for the Bachmann OT200"
 568         depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST)
 569         help
 570           This option enables support for the LEDs on the Bachmann OT200.
 571           Say Y to enable LEDs on the Bachmann OT200.
 572
 573 config LEDS_MENF21BMC
 574         tristate "LED support for the MEN 14F021P00 BMC"
 575         depends on LEDS_CLASS && MFD_MENF21BMC
 576         help
 577           Say Y here to include support for the MEN 14F021P00 BMC LEDs.
 578
 579           This driver can also be built as a module. If so the module
 580           will be called leds-menf21bmc.
 581
 582 config LEDS_KTD2692
 583         tristate "LED support for KTD2692 flash LED controller"
 584         depends on LEDS_CLASS_FLASH && OF
 585         depends on GPIOLIB || COMPILE_TEST
 586         help
 587           This option enables support for KTD2692 LED flash connected
 588           through ExpressWire interface.
 589
 590           Say Y to enable this driver.
 591
 592 config LEDS_IS31FL319X
 593         tristate "LED Support for ISSI IS31FL319x I2C LED controller family"
 594         depends on LEDS_CLASS && I2C && OF
 595         select REGMAP_I2C
 596         help
 597           This option enables support for LEDs connected to ISSI IS31FL319x
 598           fancy LED driver chips accessed via the I2C bus.
 599           Driver supports individual PWM brightness control for each channel.
 600
 601           This driver can also be built as a module. If so the module will be
 602           called leds-is31fl319x.
 603
 604 config LEDS_IS31FL32XX
 605         tristate "LED support for ISSI IS31FL32XX I2C LED controller family"
 606         depends on LEDS_CLASS && I2C && OF
 607         help
 608           Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
 609           LED controllers. They are I2C devices with multiple constant-current
 610           channels, each with independent 256-level PWM control.
 611
 612 comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"
 613
 614 config LEDS_BLINKM
 615         tristate "LED support for the BlinkM I2C RGB LED"
 616         depends on LEDS_CLASS
 617         depends on I2C
 618         help
 619           This option enables support for the BlinkM RGB LED connected
 620           through I2C. Say Y to enable support for the BlinkM LED.
 621
 622 config LEDS_POWERNV
 623         tristate "LED support for PowerNV Platform"
 624         depends on LEDS_CLASS
 625         depends on PPC_POWERNV
 626         depends on OF
 627         help
 628           This option enables support for the system LEDs present on
 629           PowerNV platforms. Say 'y' to enable this support in kernel.
 630           To compile this driver as a module, choose 'm' here: the module
 631           will be called leds-powernv.
 632
 633 config LEDS_SYSCON
 634         bool "LED support for LEDs on system controllers"
 635         depends on LEDS_CLASS=y
 636         depends on MFD_SYSCON
 637         depends on OF
 638         help
 639           This option enabled support for the LEDs on syscon type
 640           devices. This will only work with device tree enabled
 641           devices.
 642
 643 config LEDS_PM8058
 644         tristate "LED Support for the Qualcomm PM8058 PMIC"
 645         depends on MFD_PM8XXX
 646         depends on LEDS_CLASS
 647         help
 648           Choose this option if you want to use the LED drivers in
 649           the Qualcomm PM8058 PMIC.
 650
 651 config LEDS_MLXCPLD
 652         tristate "LED support for the Mellanox boards"
 653         depends on X86_64 && DMI
 654         depends on LEDS_CLASS
 655         help
 656           This option enabled support for the LEDs on the Mellanox
 657           boards. Say Y to enabled these.
 658
 659 config LEDS_USER
 660         tristate "Userspace LED support"
 661         depends on LEDS_CLASS
 662         help
 663           This option enables support for userspace LEDs. Say 'y' to enable this
 664           support in kernel. To compile this driver as a module, choose 'm' here:
 665           the module will be called uleds.
 666
 667 config LEDS_NIC78BX
 668         tristate "LED support for NI PXI NIC78bx devices"
 669         depends on LEDS_CLASS
 670         depends on X86 && ACPI
 671         help
 672           This option enables support for the User1 and User2 LEDs on NI
 673           PXI NIC78bx devices.
 674
 675           To compile this driver as a module, choose M here: the module
 676           will be called leds-nic78bx.
 677
 678 comment "LED Triggers"
 679 source "drivers/leds/trigger/Kconfig"
 680
 681 endif # NEW_LEDS