drivers/mtd/nand/Kconfig

   1 config MTD_NAND_ECC
   2         tristate
   3
   4 config MTD_NAND_ECC_SMC
   5         bool "NAND ECC Smart Media byte order"
   6         depends on MTD_NAND_ECC
   7         default n
   8         help
   9           Software ECC according to the Smart Media Specification.
  10           The original Linux implementation had byte 0 and 1 swapped.
  11
  12
  13 menuconfig MTD_NAND
  14         tristate "NAND Device Support"
  15         depends on MTD
  16         select MTD_NAND_IDS
  17         select MTD_NAND_ECC
  18         help
  19           This enables support for accessing all type of NAND flash
  20           devices. For further information see
  21           <http://www.linux-mtd.infradead.org/doc/nand.html>.
  22
  23 if MTD_NAND
  24
  25 config MTD_NAND_BCH
  26         tristate
  27         select BCH
  28         depends on MTD_NAND_ECC_BCH
  29         default MTD_NAND
  30
  31 config MTD_NAND_ECC_BCH
  32         bool "Support software BCH ECC"
  33         default n
  34         help
  35           This enables support for software BCH error correction. Binary BCH
  36           codes are more powerful and cpu intensive than traditional Hamming
  37           ECC codes. They are used with NAND devices requiring more than 1 bit
  38           of error correction.
  39
  40 config MTD_SM_COMMON
  41         tristate
  42         default n
  43
  44 config MTD_NAND_DENALI
  45         tristate
  46
  47 config MTD_NAND_DENALI_PCI
  48         tristate "Support Denali NAND controller on Intel Moorestown"
  49         select MTD_NAND_DENALI
  50         depends on HAS_DMA && PCI
  51         help
  52           Enable the driver for NAND flash on Intel Moorestown, using the
  53           Denali NAND controller core.
  54
  55 config MTD_NAND_DENALI_DT
  56         tristate "Support Denali NAND controller as a DT device"
  57         select MTD_NAND_DENALI
  58         depends on HAS_DMA && HAVE_CLK && OF
  59         help
  60           Enable the driver for NAND flash on platforms using a Denali NAND
  61           controller as a DT device.
  62
  63 config MTD_NAND_DENALI_SCRATCH_REG_ADDR
  64         hex "Denali NAND size scratch register address"
  65         default "0xFF108018"
  66         depends on MTD_NAND_DENALI_PCI
  67         help
  68           Some platforms place the NAND chip size in a scratch register
  69           because (some versions of) the driver aren't able to automatically
  70           determine the size of certain chips. Set the address of the
  71           scratch register here to enable this feature. On Intel Moorestown
  72           boards, the scratch register is at 0xFF108018.
  73
  74 config MTD_NAND_GPIO
  75         tristate "GPIO assisted NAND Flash driver"
  76         depends on GPIOLIB || COMPILE_TEST
  77         depends on HAS_IOMEM
  78         help
  79           This enables a NAND flash driver where control signals are
  80           connected to GPIO pins, and commands and data are communicated
  81           via a memory mapped interface.
  82
  83 config MTD_NAND_AMS_DELTA
  84         tristate "NAND Flash device on Amstrad E3"
  85         depends on MACH_AMS_DELTA
  86         default y
  87         help
  88           Support for NAND flash on Amstrad E3 (Delta).
  89
  90 config MTD_NAND_OMAP2
  91         tristate "NAND Flash device on OMAP2, OMAP3, OMAP4 and Keystone"
  92         depends on (ARCH_OMAP2PLUS || ARCH_KEYSTONE)
  93         help
  94           Support for NAND flash on Texas Instruments OMAP2, OMAP3, OMAP4
  95           and Keystone platforms.
  96
  97 config MTD_NAND_OMAP_BCH
  98         depends on MTD_NAND_OMAP2
  99         bool "Support hardware based BCH error correction"
 100         default n
 101         select BCH
 102         help
 103           This config enables the ELM hardware engine, which can be used to
 104           locate and correct errors when using BCH ECC scheme. This offloads
 105           the cpu from doing ECC error searching and correction. However some
 106           legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine
 107           so this is optional for them.
 108
 109 config MTD_NAND_OMAP_BCH_BUILD
 110         def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH
 111
 112 config MTD_NAND_IDS
 113         tristate
 114
 115 config MTD_NAND_RICOH
 116         tristate "Ricoh xD card reader"
 117         default n
 118         depends on PCI
 119         select MTD_SM_COMMON
 120         help
 121           Enable support for Ricoh R5C852 xD card reader
 122           You also need to enable ether
 123           NAND SSFDC (SmartMedia) read only translation layer' or new
 124           expermental, readwrite
 125           'SmartMedia/xD new translation layer'
 126
 127 config MTD_NAND_AU1550
 128         tristate "Au1550/1200 NAND support"
 129         depends on MIPS_ALCHEMY
 130         help
 131           This enables the driver for the NAND flash controller on the
 132           AMD/Alchemy 1550 SOC.
 133
 134 config MTD_NAND_BF5XX
 135         tristate "Blackfin on-chip NAND Flash Controller driver"
 136         depends on BF54x || BF52x
 137         help
 138           This enables the Blackfin on-chip NAND flash controller
 139
 140           No board specific support is done by this driver, each board
 141           must advertise a platform_device for the driver to attach.
 142
 143           This driver can also be built as a module. If so, the module
 144           will be called bf5xx-nand.
 145
 146 config MTD_NAND_BF5XX_HWECC
 147         bool "BF5XX NAND Hardware ECC"
 148         default y
 149         depends on MTD_NAND_BF5XX
 150         help
 151           Enable the use of the BF5XX's internal ECC generator when
 152           using NAND.
 153
 154 config MTD_NAND_BF5XX_BOOTROM_ECC
 155         bool "Use Blackfin BootROM ECC Layout"
 156         default n
 157         depends on MTD_NAND_BF5XX_HWECC
 158         help
 159           If you wish to modify NAND pages and allow the Blackfin on-chip
 160           BootROM to boot from them, say Y here.  This is only necessary
 161           if you are booting U-Boot out of NAND and you wish to update
 162           U-Boot from Linux' userspace.  Otherwise, you should say N here.
 163
 164           If unsure, say N.
 165
 166 config MTD_NAND_S3C2410
 167         tristate "NAND Flash support for Samsung S3C SoCs"
 168         depends on ARCH_S3C24XX || ARCH_S3C64XX
 169         help
 170           This enables the NAND flash controller on the S3C24xx and S3C64xx
 171           SoCs
 172
 173           No board specific support is done by this driver, each board
 174           must advertise a platform_device for the driver to attach.
 175
 176 config MTD_NAND_S3C2410_DEBUG
 177         bool "Samsung S3C NAND driver debug"
 178         depends on MTD_NAND_S3C2410
 179         help
 180           Enable debugging of the S3C NAND driver
 181
 182 config MTD_NAND_S3C2410_HWECC
 183         bool "Samsung S3C NAND Hardware ECC"
 184         depends on MTD_NAND_S3C2410
 185         help
 186           Enable the use of the controller's internal ECC generator when
 187           using NAND. Early versions of the chips have had problems with
 188           incorrect ECC generation, and if using these, the default of
 189           software ECC is preferable.
 190
 191 config MTD_NAND_NDFC
 192         tristate "NDFC NanD Flash Controller"
 193         depends on 4xx
 194         select MTD_NAND_ECC_SMC
 195         help
 196          NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs
 197
 198 config MTD_NAND_S3C2410_CLKSTOP
 199         bool "Samsung S3C NAND IDLE clock stop"
 200         depends on MTD_NAND_S3C2410
 201         default n
 202         help
 203           Stop the clock to the NAND controller when there is no chip
 204           selected to save power. This will mean there is a small delay
 205           when the is NAND chip selected or released, but will save
 206           approximately 5mA of power when there is nothing happening.
 207
 208 config MTD_NAND_DISKONCHIP
 209         tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)"
 210         depends on HAS_IOMEM
 211         select REED_SOLOMON
 212         select REED_SOLOMON_DEC16
 213         help
 214           This is a reimplementation of M-Systems DiskOnChip 2000,
 215           Millennium and Millennium Plus as a standard NAND device driver,
 216           as opposed to the earlier self-contained MTD device drivers.
 217           This should enable, among other things, proper JFFS2 operation on
 218           these devices.
 219
 220 config MTD_NAND_DISKONCHIP_PROBE_ADVANCED
 221         bool "Advanced detection options for DiskOnChip"
 222         depends on MTD_NAND_DISKONCHIP
 223         help
 224           This option allows you to specify nonstandard address at which to
 225           probe for a DiskOnChip, or to change the detection options.  You
 226           are unlikely to need any of this unless you are using LinuxBIOS.
 227           Say 'N'.
 228
 229 config MTD_NAND_DISKONCHIP_PROBE_ADDRESS
 230         hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED
 231         depends on MTD_NAND_DISKONCHIP
 232         default "0"
 233         ---help---
 234         By default, the probe for DiskOnChip devices will look for a
 235         DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
 236         This option allows you to specify a single address at which to probe
 237         for the device, which is useful if you have other devices in that
 238         range which get upset when they are probed.
 239
 240         (Note that on PowerPC, the normal probe will only check at
 241         0xE4000000.)
 242
 243         Normally, you should leave this set to zero, to allow the probe at
 244         the normal addresses.
 245
 246 config MTD_NAND_DISKONCHIP_PROBE_HIGH
 247         bool "Probe high addresses"
 248         depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED
 249         help
 250           By default, the probe for DiskOnChip devices will look for a
 251           DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.
 252           This option changes to make it probe between 0xFFFC8000 and
 253           0xFFFEE000.  Unless you are using LinuxBIOS, this is unlikely to be
 254           useful to you.  Say 'N'.
 255
 256 config MTD_NAND_DISKONCHIP_BBTWRITE
 257         bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP"
 258         depends on MTD_NAND_DISKONCHIP
 259         help
 260           On DiskOnChip devices shipped with the INFTL filesystem (Millennium
 261           and 2000 TSOP/Alon), Linux reserves some space at the end of the
 262           device for the Bad Block Table (BBT).  If you have existing INFTL
 263           data on your device (created by non-Linux tools such as M-Systems'
 264           DOS drivers), your data might overlap the area Linux wants to use for
 265           the BBT.  If this is a concern for you, leave this option disabled and
 266           Linux will not write BBT data into this area.
 267           The downside of leaving this option disabled is that if bad blocks
 268           are detected by Linux, they will not be recorded in the BBT, which
 269           could cause future problems.
 270           Once you enable this option, new filesystems (INFTL or others, created
 271           in Linux or other operating systems) will not use the reserved area.
 272           The only reason not to enable this option is to prevent damage to
 273           preexisting filesystems.
 274           Even if you leave this disabled, you can enable BBT writes at module
 275           load time (assuming you build diskonchip as a module) with the module
 276           parameter "inftl_bbt_write=1".
 277
 278 config MTD_NAND_DOCG4
 279         tristate "Support for DiskOnChip G4"
 280         depends on HAS_IOMEM
 281         select BCH
 282         select BITREVERSE
 283         help
 284           Support for diskonchip G4 nand flash, found in various smartphones and
 285           PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba
 286           Portege G900, Asus P526, and O2 XDA Zinc.
 287
 288           With this driver you will be able to use UBI and create a ubifs on the
 289           device, so you may wish to consider enabling UBI and UBIFS as well.
 290
 291           These devices ship with the Mys/Sandisk SAFTL formatting, for which
 292           there is currently no mtd parser, so you may want to use command line
 293           partitioning to segregate write-protected blocks. On the Treo680, the
 294           first five erase blocks (256KiB each) are write-protected, followed
 295           by the block containing the saftl partition table.  This is probably
 296           typical.
 297
 298 config MTD_NAND_SHARPSL
 299         tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
 300         depends on ARCH_PXA
 301
 302 config MTD_NAND_CAFE
 303         tristate "NAND support for OLPC CAFÉ chip"
 304         depends on PCI
 305         select REED_SOLOMON
 306         select REED_SOLOMON_DEC16
 307         help
 308           Use NAND flash attached to the CAFÉ chip designed for the OLPC
 309           laptop.
 310
 311 config MTD_NAND_CS553X
 312         tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"
 313         depends on X86_32
 314         depends on !UML && HAS_IOMEM
 315         help
 316           The CS553x companion chips for the AMD Geode processor
 317           include NAND flash controllers with built-in hardware ECC
 318           capabilities; enabling this option will allow you to use
 319           these. The driver will check the MSRs to verify that the
 320           controller is enabled for NAND, and currently requires that
 321           the controller be in MMIO mode.
 322
 323           If you say "m", the module will be called cs553x_nand.
 324
 325 config MTD_NAND_ATMEL
 326         tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32"
 327         depends on ARCH_AT91 || AVR32
 328         help
 329           Enables support for NAND Flash / Smart Media Card interface
 330           on Atmel AT91 and AVR32 processors.
 331
 332 config MTD_NAND_PXA3xx
 333         tristate "NAND support on PXA3xx and Armada 370/XP"
 334         depends on PXA3xx || ARCH_MMP || PLAT_ORION
 335         help
 336           This enables the driver for the NAND flash device found on
 337           PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
 338
 339 config MTD_NAND_SLC_LPC32XX
 340         tristate "NXP LPC32xx SLC Controller"
 341         depends on ARCH_LPC32XX
 342         help
 343           Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell
 344           chips) NAND controller. This is the default for the PHYTEC 3250
 345           reference board which contains a NAND256R3A2CZA6 chip.
 346
 347           Please check the actual NAND chip connected and its support
 348           by the SLC NAND controller.
 349
 350 config MTD_NAND_MLC_LPC32XX
 351         tristate "NXP LPC32xx MLC Controller"
 352         depends on ARCH_LPC32XX
 353         help
 354           Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND
 355           controller. This is the default for the WORK92105 controller
 356           board.
 357
 358           Please check the actual NAND chip connected and its support
 359           by the MLC NAND controller.
 360
 361 config MTD_NAND_CM_X270
 362         tristate "Support for NAND Flash on CM-X270 modules"
 363         depends on MACH_ARMCORE
 364
 365 config MTD_NAND_PASEMI
 366         tristate "NAND support for PA Semi PWRficient"
 367         depends on PPC_PASEMI
 368         help
 369           Enables support for NAND Flash interface on PA Semi PWRficient
 370           based boards
 371
 372 config MTD_NAND_TMIO
 373         tristate "NAND Flash device on Toshiba Mobile IO Controller"
 374         depends on MFD_TMIO
 375         help
 376           Support for NAND flash connected to a Toshiba Mobile IO
 377           Controller in some PDAs, including the Sharp SL6000x.
 378
 379 config MTD_NAND_NANDSIM
 380         tristate "Support for NAND Flash Simulator"
 381         help
 382           The simulator may simulate various NAND flash chips for the
 383           MTD nand layer.
 384
 385 config MTD_NAND_GPMI_NAND
 386         tristate "GPMI NAND Flash Controller driver"
 387         depends on MTD_NAND && MXS_DMA
 388         help
 389          Enables NAND Flash support for IMX23, IMX28 or IMX6.
 390          The GPMI controller is very powerful, with the help of BCH
 391          module, it can do the hardware ECC. The GPMI supports several
 392          NAND flashs at the same time. The GPMI may conflicts with other
 393          block, such as SD card. So pay attention to it when you enable
 394          the GPMI.
 395
 396 config MTD_NAND_BRCMNAND
 397         tristate "Broadcom STB NAND controller"
 398         depends on ARM || ARM64 || MIPS
 399         help
 400           Enables the Broadcom NAND controller driver. The controller was
 401           originally designed for Set-Top Box but is used on various BCM7xxx,
 402           BCM3xxx, BCM63xxx, iProc/Cygnus and more.
 403
 404 config MTD_NAND_BCM47XXNFLASH
 405         tristate "Support for NAND flash on BCM4706 BCMA bus"
 406         depends on BCMA_NFLASH
 407         help
 408           BCMA bus can have various flash memories attached, they are
 409           registered by bcma as platform devices. This enables driver for
 410           NAND flash memories. For now only BCM4706 is supported.
 411
 412 config MTD_NAND_PLATFORM
 413         tristate "Support for generic platform NAND driver"
 414         depends on HAS_IOMEM
 415         help
 416           This implements a generic NAND driver for on-SOC platform
 417           devices. You will need to provide platform-specific functions
 418           via platform_data.
 419
 420 config MTD_NAND_ORION
 421         tristate "NAND Flash support for Marvell Orion SoC"
 422         depends on PLAT_ORION
 423         help
 424           This enables the NAND flash controller on Orion machines.
 425
 426           No board specific support is done by this driver, each board
 427           must advertise a platform_device for the driver to attach.
 428
 429 config MTD_NAND_OXNAS
 430         tristate "NAND Flash support for Oxford Semiconductor SoC"
 431         help
 432           This enables the NAND flash controller on Oxford Semiconductor SoCs.
 433
 434 config MTD_NAND_FSL_ELBC
 435         tristate "NAND support for Freescale eLBC controllers"
 436         depends on FSL_SOC
 437         select FSL_LBC
 438         help
 439           Various Freescale chips, including the 8313, include a NAND Flash
 440           Controller Module with built-in hardware ECC capabilities.
 441           Enabling this option will enable you to use this to control
 442           external NAND devices.
 443
 444 config MTD_NAND_FSL_IFC
 445         tristate "NAND support for Freescale IFC controller"
 446         depends on FSL_SOC || ARCH_LAYERSCAPE
 447         select FSL_IFC
 448         select MEMORY
 449         help
 450           Various Freescale chips e.g P1010, include a NAND Flash machine
 451           with built-in hardware ECC capabilities.
 452           Enabling this option will enable you to use this to control
 453           external NAND devices.
 454
 455 config MTD_NAND_FSL_UPM
 456         tristate "Support for NAND on Freescale UPM"
 457         depends on PPC_83xx || PPC_85xx
 458         select FSL_LBC
 459         help
 460           Enables support for NAND Flash chips wired onto Freescale PowerPC
 461           processor localbus with User-Programmable Machine support.
 462
 463 config MTD_NAND_MPC5121_NFC
 464         tristate "MPC5121 built-in NAND Flash Controller support"
 465         depends on PPC_MPC512x
 466         help
 467           This enables the driver for the NAND flash controller on the
 468           MPC5121 SoC.
 469
 470 config MTD_NAND_VF610_NFC
 471         tristate "Support for Freescale NFC for VF610/MPC5125"
 472         depends on (SOC_VF610 || COMPILE_TEST)
 473         depends on HAS_IOMEM
 474         help
 475           Enables support for NAND Flash Controller on some Freescale
 476           processors like the VF610, MPC5125, MCF54418 or Kinetis K70.
 477           The driver supports a maximum 2k page size. With 2k pages and
 478           64 bytes or more of OOB, hardware ECC with up to 32-bit error
 479           correction is supported. Hardware ECC is only enabled through
 480           device tree.
 481
 482 config MTD_NAND_MXC
 483         tristate "MXC NAND support"
 484         depends on ARCH_MXC
 485         help
 486           This enables the driver for the NAND flash controller on the
 487           MXC processors.
 488
 489 config MTD_NAND_SH_FLCTL
 490         tristate "Support for NAND on Renesas SuperH FLCTL"
 491         depends on SUPERH || COMPILE_TEST
 492         depends on HAS_IOMEM
 493         depends on HAS_DMA
 494         help
 495           Several Renesas SuperH CPU has FLCTL. This option enables support
 496           for NAND Flash using FLCTL.
 497
 498 config MTD_NAND_DAVINCI
 499         tristate "Support NAND on DaVinci/Keystone SoC"
 500         depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF)
 501         help
 502           Enable the driver for NAND flash chips on Texas Instruments
 503           DaVinci/Keystone processors.
 504
 505 config MTD_NAND_TXX9NDFMC
 506         tristate "NAND Flash support for TXx9 SoC"
 507         depends on SOC_TX4938 || SOC_TX4939
 508         help
 509           This enables the NAND flash controller on the TXx9 SoCs.
 510
 511 config MTD_NAND_SOCRATES
 512         tristate "Support for NAND on Socrates board"
 513         depends on SOCRATES
 514         help
 515           Enables support for NAND Flash chips wired onto Socrates board.
 516
 517 config MTD_NAND_NUC900
 518         tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards."
 519         depends on ARCH_W90X900
 520         help
 521           This enables the driver for the NAND Flash on evaluation board based
 522           on w90p910 / NUC9xx.
 523
 524 config MTD_NAND_JZ4740
 525         tristate "Support for JZ4740 SoC NAND controller"
 526         depends on MACH_JZ4740
 527         help
 528                 Enables support for NAND Flash on JZ4740 SoC based boards.
 529
 530 config MTD_NAND_JZ4780
 531         tristate "Support for NAND on JZ4780 SoC"
 532         depends on MACH_JZ4780 && JZ4780_NEMC
 533         help
 534           Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
 535           based boards, using the BCH controller for hardware error correction.
 536
 537 config MTD_NAND_FSMC
 538         tristate "Support for NAND on ST Micros FSMC"
 539         depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300
 540         help
 541           Enables support for NAND Flash chips on the ST Microelectronics
 542           Flexible Static Memory Controller (FSMC)
 543
 544 config MTD_NAND_XWAY
 545         tristate "Support for NAND on Lantiq XWAY SoC"
 546         depends on LANTIQ && SOC_TYPE_XWAY
 547         help
 548           Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
 549           to the External Bus Unit (EBU).
 550
 551 config MTD_NAND_SUNXI
 552         tristate "Support for NAND on Allwinner SoCs"
 553         depends on ARCH_SUNXI
 554         help
 555           Enables support for NAND Flash chips on Allwinner SoCs.
 556
 557 config MTD_NAND_HISI504
 558         tristate "Support for NAND controller on Hisilicon SoC Hip04"
 559         depends on HAS_DMA
 560         help
 561           Enables support for NAND controller on Hisilicon SoC Hip04.
 562
 563 config MTD_NAND_QCOM
 564         tristate "Support for NAND on QCOM SoCs"
 565         depends on ARCH_QCOM
 566         help
 567           Enables support for NAND flash chips on SoCs containing the EBI2 NAND
 568           controller. This controller is found on IPQ806x SoC.
 569
 570 config MTD_NAND_MTK
 571         tristate "Support for NAND controller on MTK SoCs"
 572         depends on HAS_DMA
 573         help
 574           Enables support for NAND controller on MTK SoCs.
 575           This controller is found on mt27xx, mt81xx, mt65xx SoCs.
 576
 577 endif # MTD_NAND