3 * xHCI host controller driver
5 * Copyright (C) 2008 Intel Corp.
8 * Some code borrowed from the Linux EHCI driver.
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License version 2 as
12 * published by the Free Software Foundation.
14 * This program is distributed in the hope that it will be useful, but
15 * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
16 * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software Foundation,
21 * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
24 #ifndef __LINUX_XHCI_HCD_H
25 #define __LINUX_XHCI_HCD_H
27 #include <linux/usb.h>
28 #include <linux/timer.h>
29 #include <linux/kernel.h>
30 #include <linux/usb/hcd.h>
31 #include <linux/io-64-nonatomic-lo-hi.h>
33 /* Code sharing between pci-quirks and xhci hcd */
34 #include "xhci-ext-caps.h"
35 #include "pci-quirks.h"
37 /* xHCI PCI Configuration Registers */
38 #define XHCI_SBRN_OFFSET (0x60)
40 /* Max number of USB devices for any host controller - limit in section 6.1 */
41 #define MAX_HC_SLOTS 256
42 /* Section 5.3.3 - MaxPorts */
43 #define MAX_HC_PORTS 127
46 * xHCI register interface.
47 * This corresponds to the eXtensible Host Controller Interface (xHCI)
48 * Revision 0.95 specification
52 * struct xhci_cap_regs - xHCI Host Controller Capability Registers.
53 * @hc_capbase: length of the capabilities register and HC version number
54 * @hcs_params1: HCSPARAMS1 - Structural Parameters 1
55 * @hcs_params2: HCSPARAMS2 - Structural Parameters 2
56 * @hcs_params3: HCSPARAMS3 - Structural Parameters 3
57 * @hcc_params: HCCPARAMS - Capability Parameters
58 * @db_off: DBOFF - Doorbell array offset
59 * @run_regs_off: RTSOFF - Runtime register space offset
60 * @hcc_params2: HCCPARAMS2 Capability Parameters 2, xhci 1.1 only
62 struct xhci_cap_regs
{
70 __le32 hcc_params2
; /* xhci 1.1 */
71 /* Reserved up to (CAPLENGTH - 0x1C) */
74 /* hc_capbase bitmasks */
75 /* bits 7:0 - how long is the Capabilities register */
76 #define HC_LENGTH(p) XHCI_HC_LENGTH(p)
78 #define HC_VERSION(p) (((p) >> 16) & 0xffff)
80 /* HCSPARAMS1 - hcs_params1 - bitmasks */
81 /* bits 0:7, Max Device Slots */
82 #define HCS_MAX_SLOTS(p) (((p) >> 0) & 0xff)
83 #define HCS_SLOTS_MASK 0xff
84 /* bits 8:18, Max Interrupters */
85 #define HCS_MAX_INTRS(p) (((p) >> 8) & 0x7ff)
86 /* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
87 #define HCS_MAX_PORTS(p) (((p) >> 24) & 0x7f)
89 /* HCSPARAMS2 - hcs_params2 - bitmasks */
90 /* bits 0:3, frames or uframes that SW needs to queue transactions
91 * ahead of the HW to meet periodic deadlines */
92 #define HCS_IST(p) (((p) >> 0) & 0xf)
93 /* bits 4:7, max number of Event Ring segments */
94 #define HCS_ERST_MAX(p) (((p) >> 4) & 0xf)
95 /* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */
96 /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
97 /* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */
98 #define HCS_MAX_SCRATCHPAD(p) ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f))
100 /* HCSPARAMS3 - hcs_params3 - bitmasks */
101 /* bits 0:7, Max U1 to U0 latency for the roothub ports */
102 #define HCS_U1_LATENCY(p) (((p) >> 0) & 0xff)
103 /* bits 16:31, Max U2 to U0 latency for the roothub ports */
104 #define HCS_U2_LATENCY(p) (((p) >> 16) & 0xffff)
106 /* HCCPARAMS - hcc_params - bitmasks */
107 /* true: HC can use 64-bit address pointers */
108 #define HCC_64BIT_ADDR(p) ((p) & (1 << 0))
109 /* true: HC can do bandwidth negotiation */
110 #define HCC_BANDWIDTH_NEG(p) ((p) & (1 << 1))
111 /* true: HC uses 64-byte Device Context structures
112 * FIXME 64-byte context structures aren't supported yet.
114 #define HCC_64BYTE_CONTEXT(p) ((p) & (1 << 2))
115 /* true: HC has port power switches */
116 #define HCC_PPC(p) ((p) & (1 << 3))
117 /* true: HC has port indicators */
118 #define HCS_INDICATOR(p) ((p) & (1 << 4))
119 /* true: HC has Light HC Reset Capability */
120 #define HCC_LIGHT_RESET(p) ((p) & (1 << 5))
121 /* true: HC supports latency tolerance messaging */
122 #define HCC_LTC(p) ((p) & (1 << 6))
123 /* true: no secondary Stream ID Support */
124 #define HCC_NSS(p) ((p) & (1 << 7))
125 /* true: HC supports Stopped - Short Packet */
126 #define HCC_SPC(p) ((p) & (1 << 9))
127 /* true: HC has Contiguous Frame ID Capability */
128 #define HCC_CFC(p) ((p) & (1 << 11))
129 /* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
130 #define HCC_MAX_PSA(p) (1 << ((((p) >> 12) & 0xf) + 1))
131 /* Extended Capabilities pointer from PCI base - section 5.3.6 */
132 #define HCC_EXT_CAPS(p) XHCI_HCC_EXT_CAPS(p)
134 /* db_off bitmask - bits 0:1 reserved */
135 #define DBOFF_MASK (~0x3)
137 /* run_regs_off bitmask - bits 0:4 reserved */
138 #define RTSOFF_MASK (~0x1f)
140 /* HCCPARAMS2 - hcc_params2 - bitmasks */
141 /* true: HC supports U3 entry Capability */
142 #define HCC2_U3C(p) ((p) & (1 << 0))
143 /* true: HC supports Configure endpoint command Max exit latency too large */
144 #define HCC2_CMC(p) ((p) & (1 << 1))
145 /* true: HC supports Force Save context Capability */
146 #define HCC2_FSC(p) ((p) & (1 << 2))
147 /* true: HC supports Compliance Transition Capability */
148 #define HCC2_CTC(p) ((p) & (1 << 3))
149 /* true: HC support Large ESIT payload Capability > 48k */
150 #define HCC2_LEC(p) ((p) & (1 << 4))
151 /* true: HC support Configuration Information Capability */
152 #define HCC2_CIC(p) ((p) & (1 << 5))
153 /* true: HC support Extended TBC Capability, Isoc burst count > 65535 */
154 #define HCC2_ETC(p) ((p) & (1 << 6))
156 /* Number of registers per port */
157 #define NUM_PORT_REGS 4
165 * struct xhci_op_regs - xHCI Host Controller Operational Registers.
166 * @command: USBCMD - xHC command register
167 * @status: USBSTS - xHC status register
168 * @page_size: This indicates the page size that the host controller
169 * supports. If bit n is set, the HC supports a page size
170 * of 2^(n+12), up to a 128MB page size.
171 * 4K is the minimum page size.
172 * @cmd_ring: CRP - 64-bit Command Ring Pointer
173 * @dcbaa_ptr: DCBAAP - 64-bit Device Context Base Address Array Pointer
174 * @config_reg: CONFIG - Configure Register
175 * @port_status_base: PORTSCn - base address for Port Status and Control
176 * Each port has a Port Status and Control register,
177 * followed by a Port Power Management Status and Control
178 * register, a Port Link Info register, and a reserved
180 * @port_power_base: PORTPMSCn - base address for
181 * Port Power Management Status and Control
182 * @port_link_base: PORTLIn - base address for Port Link Info (current
183 * Link PM state and control) for USB 2.1 and USB 3.0
186 struct xhci_op_regs
{
192 __le32 dev_notification
;
194 /* rsvd: offset 0x20-2F */
198 /* rsvd: offset 0x3C-3FF */
199 __le32 reserved4
[241];
200 /* port 1 registers, which serve as a base address for other ports */
201 __le32 port_status_base
;
202 __le32 port_power_base
;
203 __le32 port_link_base
;
205 /* registers for ports 2-255 */
206 __le32 reserved6
[NUM_PORT_REGS
*254];
209 /* USBCMD - USB command - command bitmasks */
210 /* start/stop HC execution - do not write unless HC is halted*/
211 #define CMD_RUN XHCI_CMD_RUN
212 /* Reset HC - resets internal HC state machine and all registers (except
213 * PCI config regs). HC does NOT drive a USB reset on the downstream ports.
214 * The xHCI driver must reinitialize the xHC after setting this bit.
216 #define CMD_RESET (1 << 1)
217 /* Event Interrupt Enable - a '1' allows interrupts from the host controller */
218 #define CMD_EIE XHCI_CMD_EIE
219 /* Host System Error Interrupt Enable - get out-of-band signal for HC errors */
220 #define CMD_HSEIE XHCI_CMD_HSEIE
221 /* bits 4:6 are reserved (and should be preserved on writes). */
222 /* light reset (port status stays unchanged) - reset completed when this is 0 */
223 #define CMD_LRESET (1 << 7)
224 /* host controller save/restore state. */
225 #define CMD_CSS (1 << 8)
226 #define CMD_CRS (1 << 9)
227 /* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */
228 #define CMD_EWE XHCI_CMD_EWE
229 /* MFINDEX power management - '1' means xHC can stop MFINDEX counter if all root
230 * hubs are in U3 (selective suspend), disconnect, disabled, or powered-off.
231 * '0' means the xHC can power it off if all ports are in the disconnect,
232 * disabled, or powered-off state.
234 #define CMD_PM_INDEX (1 << 11)
235 /* bit 14 Extended TBC Enable, changes Isoc TRB fields to support larger TBC */
236 #define CMD_ETE (1 << 14)
237 /* bits 15:31 are reserved (and should be preserved on writes). */
239 /* IMAN - Interrupt Management Register */
240 #define IMAN_IE (1 << 1)
241 #define IMAN_IP (1 << 0)
243 /* USBSTS - USB status - status bitmasks */
244 /* HC not running - set to 1 when run/stop bit is cleared. */
245 #define STS_HALT XHCI_STS_HALT
246 /* serious error, e.g. PCI parity error. The HC will clear the run/stop bit. */
247 #define STS_FATAL (1 << 2)
248 /* event interrupt - clear this prior to clearing any IP flags in IR set*/
249 #define STS_EINT (1 << 3)
250 /* port change detect */
251 #define STS_PORT (1 << 4)
252 /* bits 5:7 reserved and zeroed */
253 /* save state status - '1' means xHC is saving state */
254 #define STS_SAVE (1 << 8)
255 /* restore state status - '1' means xHC is restoring state */
256 #define STS_RESTORE (1 << 9)
257 /* true: save or restore error */
258 #define STS_SRE (1 << 10)
259 /* true: Controller Not Ready to accept doorbell or op reg writes after reset */
260 #define STS_CNR XHCI_STS_CNR
261 /* true: internal Host Controller Error - SW needs to reset and reinitialize */
262 #define STS_HCE (1 << 12)
263 /* bits 13:31 reserved and should be preserved */
266 * DNCTRL - Device Notification Control Register - dev_notification bitmasks
267 * Generate a device notification event when the HC sees a transaction with a
268 * notification type that matches a bit set in this bit field.
270 #define DEV_NOTE_MASK (0xffff)
271 #define ENABLE_DEV_NOTE(x) (1 << (x))
272 /* Most of the device notification types should only be used for debug.
273 * SW does need to pay attention to function wake notifications.
275 #define DEV_NOTE_FWAKE ENABLE_DEV_NOTE(1)
277 /* CRCR - Command Ring Control Register - cmd_ring bitmasks */
278 /* bit 0 is the command ring cycle state */
279 /* stop ring operation after completion of the currently executing command */
280 #define CMD_RING_PAUSE (1 << 1)
281 /* stop ring immediately - abort the currently executing command */
282 #define CMD_RING_ABORT (1 << 2)
283 /* true: command ring is running */
284 #define CMD_RING_RUNNING (1 << 3)
285 /* bits 4:5 reserved and should be preserved */
286 /* Command Ring pointer - bit mask for the lower 32 bits. */
287 #define CMD_RING_RSVD_BITS (0x3f)
289 /* CONFIG - Configure Register - config_reg bitmasks */
290 /* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */
291 #define MAX_DEVS(p) ((p) & 0xff)
292 /* bit 8: U3 Entry Enabled, assert PLC when root port enters U3, xhci 1.1 */
293 #define CONFIG_U3E (1 << 8)
294 /* bit 9: Configuration Information Enable, xhci 1.1 */
295 #define CONFIG_CIE (1 << 9)
296 /* bits 10:31 - reserved and should be preserved */
298 /* PORTSC - Port Status and Control Register - port_status_base bitmasks */
299 /* true: device connected */
300 #define PORT_CONNECT (1 << 0)
301 /* true: port enabled */
302 #define PORT_PE (1 << 1)
303 /* bit 2 reserved and zeroed */
304 /* true: port has an over-current condition */
305 #define PORT_OC (1 << 3)
306 /* true: port reset signaling asserted */
307 #define PORT_RESET (1 << 4)
308 /* Port Link State - bits 5:8
309 * A read gives the current link PM state of the port,
310 * a write with Link State Write Strobe set sets the link state.
312 #define PORT_PLS_MASK (0xf << 5)
313 #define XDEV_U0 (0x0 << 5)
314 #define XDEV_U1 (0x1 << 5)
315 #define XDEV_U2 (0x2 << 5)
316 #define XDEV_U3 (0x3 << 5)
317 #define XDEV_DISABLED (0x4 << 5)
318 #define XDEV_RXDETECT (0x5 << 5)
319 #define XDEV_INACTIVE (0x6 << 5)
320 #define XDEV_POLLING (0x7 << 5)
321 #define XDEV_RECOVERY (0x8 << 5)
322 #define XDEV_HOT_RESET (0x9 << 5)
323 #define XDEV_COMP_MODE (0xa << 5)
324 #define XDEV_TEST_MODE (0xb << 5)
325 #define XDEV_RESUME (0xf << 5)
327 /* true: port has power (see HCC_PPC) */
328 #define PORT_POWER (1 << 9)
329 /* bits 10:13 indicate device speed:
330 * 0 - undefined speed - port hasn't be initialized by a reset yet
337 #define DEV_SPEED_MASK (0xf << 10)
338 #define XDEV_FS (0x1 << 10)
339 #define XDEV_LS (0x2 << 10)
340 #define XDEV_HS (0x3 << 10)
341 #define XDEV_SS (0x4 << 10)
342 #define XDEV_SSP (0x5 << 10)
343 #define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10))
344 #define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
345 #define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS)
346 #define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
347 #define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
348 #define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP)
349 #define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS)
350 #define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f)
352 /* Bits 20:23 in the Slot Context are the speed for the device */
353 #define SLOT_SPEED_FS (XDEV_FS << 10)
354 #define SLOT_SPEED_LS (XDEV_LS << 10)
355 #define SLOT_SPEED_HS (XDEV_HS << 10)
356 #define SLOT_SPEED_SS (XDEV_SS << 10)
357 #define SLOT_SPEED_SSP (XDEV_SSP << 10)
358 /* Port Indicator Control */
359 #define PORT_LED_OFF (0 << 14)
360 #define PORT_LED_AMBER (1 << 14)
361 #define PORT_LED_GREEN (2 << 14)
362 #define PORT_LED_MASK (3 << 14)
363 /* Port Link State Write Strobe - set this when changing link state */
364 #define PORT_LINK_STROBE (1 << 16)
365 /* true: connect status change */
366 #define PORT_CSC (1 << 17)
367 /* true: port enable change */
368 #define PORT_PEC (1 << 18)
369 /* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port
370 * into an enabled state, and the device into the default state. A "warm" reset
371 * also resets the link, forcing the device through the link training sequence.
372 * SW can also look at the Port Reset register to see when warm reset is done.
374 #define PORT_WRC (1 << 19)
375 /* true: over-current change */
376 #define PORT_OCC (1 << 20)
377 /* true: reset change - 1 to 0 transition of PORT_RESET */
378 #define PORT_RC (1 << 21)
379 /* port link status change - set on some port link state transitions:
381 * ------------------------------------------------------------------------------
382 * - U3 to Resume Wakeup signaling from a device
383 * - Resume to Recovery to U0 USB 3.0 device resume
384 * - Resume to U0 USB 2.0 device resume
385 * - U3 to Recovery to U0 Software resume of USB 3.0 device complete
386 * - U3 to U0 Software resume of USB 2.0 device complete
387 * - U2 to U0 L1 resume of USB 2.1 device complete
388 * - U0 to U0 (???) L1 entry rejection by USB 2.1 device
389 * - U0 to disabled L1 entry error with USB 2.1 device
390 * - Any state to inactive Error on USB 3.0 port
392 #define PORT_PLC (1 << 22)
393 /* port configure error change - port failed to configure its link partner */
394 #define PORT_CEC (1 << 23)
395 /* Cold Attach Status - xHC can set this bit to report device attached during
396 * Sx state. Warm port reset should be perfomed to clear this bit and move port
397 * to connected state.
399 #define PORT_CAS (1 << 24)
400 /* wake on connect (enable) */
401 #define PORT_WKCONN_E (1 << 25)
402 /* wake on disconnect (enable) */
403 #define PORT_WKDISC_E (1 << 26)
404 /* wake on over-current (enable) */
405 #define PORT_WKOC_E (1 << 27)
406 /* bits 28:29 reserved */
407 /* true: device is non-removable - for USB 3.0 roothub emulation */
408 #define PORT_DEV_REMOVE (1 << 30)
409 /* Initiate a warm port reset - complete when PORT_WRC is '1' */
410 #define PORT_WR (1 << 31)
412 /* We mark duplicate entries with -1 */
413 #define DUPLICATE_ENTRY ((u8)(-1))
415 /* Port Power Management Status and Control - port_power_base bitmasks */
416 /* Inactivity timer value for transitions into U1, in microseconds.
417 * Timeout can be up to 127us. 0xFF means an infinite timeout.
419 #define PORT_U1_TIMEOUT(p) ((p) & 0xff)
420 #define PORT_U1_TIMEOUT_MASK 0xff
421 /* Inactivity timer value for transitions into U2 */
422 #define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8)
423 #define PORT_U2_TIMEOUT_MASK (0xff << 8)
424 /* Bits 24:31 for port testing */
426 /* USB2 Protocol PORTSPMSC */
427 #define PORT_L1S_MASK 7
428 #define PORT_L1S_SUCCESS 1
429 #define PORT_RWE (1 << 3)
430 #define PORT_HIRD(p) (((p) & 0xf) << 4)
431 #define PORT_HIRD_MASK (0xf << 4)
432 #define PORT_L1DS_MASK (0xff << 8)
433 #define PORT_L1DS(p) (((p) & 0xff) << 8)
434 #define PORT_HLE (1 << 16)
435 #define PORT_TEST_MODE_SHIFT 28
437 /* USB3 Protocol PORTLI Port Link Information */
438 #define PORT_RX_LANES(p) (((p) >> 16) & 0xf)
439 #define PORT_TX_LANES(p) (((p) >> 20) & 0xf)
441 /* USB2 Protocol PORTHLPMC */
442 #define PORT_HIRDM(p)((p) & 3)
443 #define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
444 #define PORT_BESLD(p)(((p) & 0xf) << 10)
446 /* use 512 microseconds as USB2 LPM L1 default timeout. */
447 #define XHCI_L1_TIMEOUT 512
449 /* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
450 * Safe to use with mixed HIRD and BESL systems (host and device) and is used
451 * by other operating systems.
453 * XHCI 1.0 errata 8/14/12 Table 13 notes:
454 * "Software should choose xHC BESL/BESLD field values that do not violate a
455 * device's resume latency requirements,
456 * e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
457 * or not program values < '4' if BLC = '0' and a BESL device is attached.
459 #define XHCI_DEFAULT_BESL 4
462 * struct xhci_intr_reg - Interrupt Register Set
463 * @irq_pending: IMAN - Interrupt Management Register. Used to enable
464 * interrupts and check for pending interrupts.
465 * @irq_control: IMOD - Interrupt Moderation Register.
466 * Used to throttle interrupts.
467 * @erst_size: Number of segments in the Event Ring Segment Table (ERST).
468 * @erst_base: ERST base address.
469 * @erst_dequeue: Event ring dequeue pointer.
471 * Each interrupter (defined by a MSI-X vector) has an event ring and an Event
472 * Ring Segment Table (ERST) associated with it. The event ring is comprised of
473 * multiple segments of the same size. The HC places events on the ring and
474 * "updates the Cycle bit in the TRBs to indicate to software the current
475 * position of the Enqueue Pointer." The HCD (Linux) processes those events and
476 * updates the dequeue pointer.
478 struct xhci_intr_reg
{
487 /* irq_pending bitmasks */
488 #define ER_IRQ_PENDING(p) ((p) & 0x1)
489 /* bits 2:31 need to be preserved */
490 /* THIS IS BUGGY - FIXME - IP IS WRITE 1 TO CLEAR */
491 #define ER_IRQ_CLEAR(p) ((p) & 0xfffffffe)
492 #define ER_IRQ_ENABLE(p) ((ER_IRQ_CLEAR(p)) | 0x2)
493 #define ER_IRQ_DISABLE(p) ((ER_IRQ_CLEAR(p)) & ~(0x2))
495 /* irq_control bitmasks */
496 /* Minimum interval between interrupts (in 250ns intervals). The interval
497 * between interrupts will be longer if there are no events on the event ring.
498 * Default is 4000 (1 ms).
500 #define ER_IRQ_INTERVAL_MASK (0xffff)
501 /* Counter used to count down the time to the next interrupt - HW use only */
502 #define ER_IRQ_COUNTER_MASK (0xffff << 16)
504 /* erst_size bitmasks */
505 /* Preserve bits 16:31 of erst_size */
506 #define ERST_SIZE_MASK (0xffff << 16)
508 /* erst_dequeue bitmasks */
509 /* Dequeue ERST Segment Index (DESI) - Segment number (or alias)
510 * where the current dequeue pointer lies. This is an optional HW hint.
512 #define ERST_DESI_MASK (0x7)
513 /* Event Handler Busy (EHB) - is the event ring scheduled to be serviced by
514 * a work queue (or delayed service routine)?
516 #define ERST_EHB (1 << 3)
517 #define ERST_PTR_MASK (0xf)
520 * struct xhci_run_regs
522 * MFINDEX - current microframe number
524 * Section 5.5 Host Controller Runtime Registers:
525 * "Software should read and write these registers using only Dword (32 bit)
526 * or larger accesses"
528 struct xhci_run_regs
{
529 __le32 microframe_index
;
531 struct xhci_intr_reg ir_set
[128];
535 * struct doorbell_array
537 * Bits 0 - 7: Endpoint target
539 * Bits 16 - 31: Stream ID
543 struct xhci_doorbell_array
{
544 __le32 doorbell
[256];
547 #define DB_VALUE(ep, stream) ((((ep) + 1) & 0xff) | ((stream) << 16))
548 #define DB_VALUE_HOST 0x00000000
551 * struct xhci_protocol_caps
552 * @revision: major revision, minor revision, capability ID,
553 * and next capability pointer.
554 * @name_string: Four ASCII characters to say which spec this xHC
555 * follows, typically "USB ".
556 * @port_info: Port offset, count, and protocol-defined information.
558 struct xhci_protocol_caps
{
564 #define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff)
565 #define XHCI_EXT_PORT_MINOR(x) (((x) >> 16) & 0xff)
566 #define XHCI_EXT_PORT_PSIC(x) (((x) >> 28) & 0x0f)
567 #define XHCI_EXT_PORT_OFF(x) ((x) & 0xff)
568 #define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff)
570 #define XHCI_EXT_PORT_PSIV(x) (((x) >> 0) & 0x0f)
571 #define XHCI_EXT_PORT_PSIE(x) (((x) >> 4) & 0x03)
572 #define XHCI_EXT_PORT_PLT(x) (((x) >> 6) & 0x03)
573 #define XHCI_EXT_PORT_PFD(x) (((x) >> 8) & 0x01)
574 #define XHCI_EXT_PORT_LP(x) (((x) >> 14) & 0x03)
575 #define XHCI_EXT_PORT_PSIM(x) (((x) >> 16) & 0xffff)
577 #define PLT_MASK (0x03 << 6)
578 #define PLT_SYM (0x00 << 6)
579 #define PLT_ASYM_RX (0x02 << 6)
580 #define PLT_ASYM_TX (0x03 << 6)
583 * struct xhci_container_ctx
584 * @type: Type of context. Used to calculated offsets to contained contexts.
585 * @size: Size of the context data
586 * @bytes: The raw context data given to HW
587 * @dma: dma address of the bytes
589 * Represents either a Device or Input context. Holds a pointer to the raw
590 * memory used for the context (bytes) and dma address of it (dma).
592 struct xhci_container_ctx
{
594 #define XHCI_CTX_TYPE_DEVICE 0x1
595 #define XHCI_CTX_TYPE_INPUT 0x2
604 * struct xhci_slot_ctx
605 * @dev_info: Route string, device speed, hub info, and last valid endpoint
606 * @dev_info2: Max exit latency for device number, root hub port number
607 * @tt_info: tt_info is used to construct split transaction tokens
608 * @dev_state: slot state and device address
610 * Slot Context - section 6.2.1.1. This assumes the HC uses 32-byte context
611 * structures. If the HC uses 64-byte contexts, there is an additional 32 bytes
612 * reserved at the end of the slot context for HC internal use.
614 struct xhci_slot_ctx
{
619 /* offset 0x10 to 0x1f reserved for HC internal use */
623 /* dev_info bitmasks */
624 /* Route String - 0:19 */
625 #define ROUTE_STRING_MASK (0xfffff)
626 /* Device speed - values defined by PORTSC Device Speed field - 20:23 */
627 #define DEV_SPEED (0xf << 20)
628 #define GET_DEV_SPEED(n) (((n) & DEV_SPEED) >> 20)
629 /* bit 24 reserved */
630 /* Is this LS/FS device connected through a HS hub? - bit 25 */
631 #define DEV_MTT (0x1 << 25)
632 /* Set if the device is a hub - bit 26 */
633 #define DEV_HUB (0x1 << 26)
634 /* Index of the last valid endpoint context in this device context - 27:31 */
635 #define LAST_CTX_MASK (0x1f << 27)
636 #define LAST_CTX(p) ((p) << 27)
637 #define LAST_CTX_TO_EP_NUM(p) (((p) >> 27) - 1)
638 #define SLOT_FLAG (1 << 0)
639 #define EP0_FLAG (1 << 1)
641 /* dev_info2 bitmasks */
642 /* Max Exit Latency (ms) - worst case time to wake up all links in dev path */
643 #define MAX_EXIT (0xffff)
644 /* Root hub port number that is needed to access the USB device */
645 #define ROOT_HUB_PORT(p) (((p) & 0xff) << 16)
646 #define DEVINFO_TO_ROOT_HUB_PORT(p) (((p) >> 16) & 0xff)
647 /* Maximum number of ports under a hub device */
648 #define XHCI_MAX_PORTS(p) (((p) & 0xff) << 24)
649 #define DEVINFO_TO_MAX_PORTS(p) (((p) & (0xff << 24)) >> 24)
651 /* tt_info bitmasks */
653 * TT Hub Slot ID - for low or full speed devices attached to a high-speed hub
654 * The Slot ID of the hub that isolates the high speed signaling from
655 * this low or full-speed device. '0' if attached to root hub port.
657 #define TT_SLOT (0xff)
659 * The number of the downstream facing port of the high-speed hub
660 * '0' if the device is not low or full speed.
662 #define TT_PORT (0xff << 8)
663 #define TT_THINK_TIME(p) (((p) & 0x3) << 16)
664 #define GET_TT_THINK_TIME(p) (((p) & (0x3 << 16)) >> 16)
666 /* dev_state bitmasks */
667 /* USB device address - assigned by the HC */
668 #define DEV_ADDR_MASK (0xff)
669 /* bits 8:26 reserved */
671 #define SLOT_STATE (0x1f << 27)
672 #define GET_SLOT_STATE(p) (((p) & (0x1f << 27)) >> 27)
674 #define SLOT_STATE_DISABLED 0
675 #define SLOT_STATE_ENABLED SLOT_STATE_DISABLED
676 #define SLOT_STATE_DEFAULT 1
677 #define SLOT_STATE_ADDRESSED 2
678 #define SLOT_STATE_CONFIGURED 3
682 * @ep_info: endpoint state, streams, mult, and interval information.
683 * @ep_info2: information on endpoint type, max packet size, max burst size,
684 * error count, and whether the HC will force an event for all
686 * @deq: 64-bit ring dequeue pointer address. If the endpoint only
687 * defines one stream, this points to the endpoint transfer ring.
688 * Otherwise, it points to a stream context array, which has a
689 * ring pointer for each flow.
691 * Average TRB lengths for the endpoint ring and
692 * max payload within an Endpoint Service Interval Time (ESIT).
694 * Endpoint Context - section 6.2.1.2. This assumes the HC uses 32-byte context
695 * structures. If the HC uses 64-byte contexts, there is an additional 32 bytes
696 * reserved at the end of the endpoint context for HC internal use.
703 /* offset 0x14 - 0x1f reserved for HC internal use */
707 /* ep_info bitmasks */
709 * Endpoint State - bits 0:2
712 * 2 - halted due to halt condition - ok to manipulate endpoint ring
717 #define EP_STATE_MASK (0xf)
718 #define EP_STATE_DISABLED 0
719 #define EP_STATE_RUNNING 1
720 #define EP_STATE_HALTED 2
721 #define EP_STATE_STOPPED 3
722 #define EP_STATE_ERROR 4
723 #define GET_EP_CTX_STATE(ctx) (le32_to_cpu((ctx)->ep_info) & EP_STATE_MASK)
725 /* Mult - Max number of burtst within an interval, in EP companion desc. */
726 #define EP_MULT(p) (((p) & 0x3) << 8)
727 #define CTX_TO_EP_MULT(p) (((p) >> 8) & 0x3)
728 /* bits 10:14 are Max Primary Streams */
729 /* bit 15 is Linear Stream Array */
730 /* Interval - period between requests to an endpoint - 125u increments. */
731 #define EP_INTERVAL(p) (((p) & 0xff) << 16)
732 #define EP_INTERVAL_TO_UFRAMES(p) (1 << (((p) >> 16) & 0xff))
733 #define CTX_TO_EP_INTERVAL(p) (((p) >> 16) & 0xff)
734 #define EP_MAXPSTREAMS_MASK (0x1f << 10)
735 #define EP_MAXPSTREAMS(p) (((p) << 10) & EP_MAXPSTREAMS_MASK)
736 /* Endpoint is set up with a Linear Stream Array (vs. Secondary Stream Array) */
737 #define EP_HAS_LSA (1 << 15)
739 /* ep_info2 bitmasks */
741 * Force Event - generate transfer events for all TRBs for this endpoint
742 * This will tell the HC to ignore the IOC and ISP flags (for debugging only).
744 #define FORCE_EVENT (0x1)
745 #define ERROR_COUNT(p) (((p) & 0x3) << 1)
746 #define CTX_TO_EP_TYPE(p) (((p) >> 3) & 0x7)
747 #define EP_TYPE(p) ((p) << 3)
748 #define ISOC_OUT_EP 1
749 #define BULK_OUT_EP 2
756 /* bit 7 is Host Initiate Disable - for disabling stream selection */
757 #define MAX_BURST(p) (((p)&0xff) << 8)
758 #define CTX_TO_MAX_BURST(p) (((p) >> 8) & 0xff)
759 #define MAX_PACKET(p) (((p)&0xffff) << 16)
760 #define MAX_PACKET_MASK (0xffff << 16)
761 #define MAX_PACKET_DECODED(p) (((p) >> 16) & 0xffff)
763 /* tx_info bitmasks */
764 #define EP_AVG_TRB_LENGTH(p) ((p) & 0xffff)
765 #define EP_MAX_ESIT_PAYLOAD_LO(p) (((p) & 0xffff) << 16)
766 #define EP_MAX_ESIT_PAYLOAD_HI(p) ((((p) >> 16) & 0xff) << 24)
767 #define CTX_TO_MAX_ESIT_PAYLOAD(p) (((p) >> 16) & 0xffff)
770 #define EP_CTX_CYCLE_MASK (1 << 0)
771 #define SCTX_DEQ_MASK (~0xfL)
775 * struct xhci_input_control_context
776 * Input control context; see section 6.2.5.
778 * @drop_context: set the bit of the endpoint context you want to disable
779 * @add_context: set the bit of the endpoint context you want to enable
781 struct xhci_input_control_ctx
{
787 #define EP_IS_ADDED(ctrl_ctx, i) \
788 (le32_to_cpu(ctrl_ctx->add_flags) & (1 << (i + 1)))
789 #define EP_IS_DROPPED(ctrl_ctx, i) \
790 (le32_to_cpu(ctrl_ctx->drop_flags) & (1 << (i + 1)))
792 /* Represents everything that is needed to issue a command on the command ring.
793 * It's useful to pre-allocate these for commands that cannot fail due to
794 * out-of-memory errors, like freeing streams.
796 struct xhci_command
{
797 /* Input context for changing device state */
798 struct xhci_container_ctx
*in_ctx
;
801 /* If completion is null, no one is waiting on this command
802 * and the structure can be freed after the command completes.
804 struct completion
*completion
;
805 union xhci_trb
*command_trb
;
806 struct list_head cmd_list
;
809 /* drop context bitmasks */
810 #define DROP_EP(x) (0x1 << x)
811 /* add context bitmasks */
812 #define ADD_EP(x) (0x1 << x)
814 struct xhci_stream_ctx
{
815 /* 64-bit stream ring address, cycle state, and stream type */
817 /* offset 0x14 - 0x1f reserved for HC internal use */
821 /* Stream Context Types (section 6.4.1) - bits 3:1 of stream ctx deq ptr */
822 #define SCT_FOR_CTX(p) (((p) & 0x7) << 1)
823 /* Secondary stream array type, dequeue pointer is to a transfer ring */
825 /* Primary stream array type, dequeue pointer is to a transfer ring */
827 /* Dequeue pointer is for a secondary stream array (SSA) with 8 entries */
832 #define SCT_SSA_128 6
833 #define SCT_SSA_256 7
835 /* Assume no secondary streams for now */
836 struct xhci_stream_info
{
837 struct xhci_ring
**stream_rings
;
838 /* Number of streams, including stream 0 (which drivers can't use) */
839 unsigned int num_streams
;
840 /* The stream context array may be bigger than
841 * the number of streams the driver asked for
843 struct xhci_stream_ctx
*stream_ctx_array
;
844 unsigned int num_stream_ctxs
;
845 dma_addr_t ctx_array_dma
;
846 /* For mapping physical TRB addresses to segments in stream rings */
847 struct radix_tree_root trb_address_map
;
848 struct xhci_command
*free_streams_command
;
851 #define SMALL_STREAM_ARRAY_SIZE 256
852 #define MEDIUM_STREAM_ARRAY_SIZE 1024
854 /* Some Intel xHCI host controllers need software to keep track of the bus
855 * bandwidth. Keep track of endpoint info here. Each root port is allocated
856 * the full bus bandwidth. We must also treat TTs (including each port under a
857 * multi-TT hub) as a separate bandwidth domain. The direct memory interface
858 * (DMI) also limits the total bandwidth (across all domains) that can be used.
860 struct xhci_bw_info
{
861 /* ep_interval is zero-based */
862 unsigned int ep_interval
;
863 /* mult and num_packets are one-based */
865 unsigned int num_packets
;
866 unsigned int max_packet_size
;
867 unsigned int max_esit_payload
;
871 /* "Block" sizes in bytes the hardware uses for different device speeds.
872 * The logic in this part of the hardware limits the number of bits the hardware
873 * can use, so must represent bandwidth in a less precise manner to mimic what
874 * the scheduler hardware computes.
881 /* Each device speed has a protocol overhead (CRC, bit stuffing, etc) associated
882 * with each byte transferred. SuperSpeed devices have an initial overhead to
883 * set up bursts. These are in blocks, see above. LS overhead has already been
884 * translated into FS blocks.
886 #define DMI_OVERHEAD 8
887 #define DMI_OVERHEAD_BURST 4
888 #define SS_OVERHEAD 8
889 #define SS_OVERHEAD_BURST 32
890 #define HS_OVERHEAD 26
891 #define FS_OVERHEAD 20
892 #define LS_OVERHEAD 128
893 /* The TTs need to claim roughly twice as much bandwidth (94 bytes per
894 * microframe ~= 24Mbps) of the HS bus as the devices can actually use because
895 * of overhead associated with split transfers crossing microframe boundaries.
896 * 31 blocks is pure protocol overhead.
898 #define TT_HS_OVERHEAD (31 + 94)
899 #define TT_DMI_OVERHEAD (25 + 12)
901 /* Bandwidth limits in blocks */
902 #define FS_BW_LIMIT 1285
903 #define TT_BW_LIMIT 1320
904 #define HS_BW_LIMIT 1607
905 #define SS_BW_LIMIT_IN 3906
906 #define DMI_BW_LIMIT_IN 3906
907 #define SS_BW_LIMIT_OUT 3906
908 #define DMI_BW_LIMIT_OUT 3906
910 /* Percentage of bus bandwidth reserved for non-periodic transfers */
911 #define FS_BW_RESERVED 10
912 #define HS_BW_RESERVED 20
913 #define SS_BW_RESERVED 10
915 struct xhci_virt_ep
{
916 struct xhci_ring
*ring
;
917 /* Related to endpoints that are configured to use stream IDs only */
918 struct xhci_stream_info
*stream_info
;
919 /* Temporary storage in case the configure endpoint command fails and we
920 * have to restore the device state to the previous state
922 struct xhci_ring
*new_ring
;
923 unsigned int ep_state
;
924 #define SET_DEQ_PENDING (1 << 0)
925 #define EP_HALTED (1 << 1) /* For stall handling */
926 #define EP_STOP_CMD_PENDING (1 << 2) /* For URB cancellation */
927 /* Transitioning the endpoint to using streams, don't enqueue URBs */
928 #define EP_GETTING_STREAMS (1 << 3)
929 #define EP_HAS_STREAMS (1 << 4)
930 /* Transitioning the endpoint to not using streams, don't enqueue URBs */
931 #define EP_GETTING_NO_STREAMS (1 << 5)
932 /* ---- Related to URB cancellation ---- */
933 struct list_head cancelled_td_list
;
934 /* Watchdog timer for stop endpoint command to cancel URBs */
935 struct timer_list stop_cmd_timer
;
936 struct xhci_hcd
*xhci
;
937 /* Dequeue pointer and dequeue segment for a submitted Set TR Dequeue
938 * command. We'll need to update the ring's dequeue segment and dequeue
939 * pointer after the command completes.
941 struct xhci_segment
*queued_deq_seg
;
942 union xhci_trb
*queued_deq_ptr
;
944 * Sometimes the xHC can not process isochronous endpoint ring quickly
945 * enough, and it will miss some isoc tds on the ring and generate
946 * a Missed Service Error Event.
947 * Set skip flag when receive a Missed Service Error Event and
948 * process the missed tds on the endpoint ring.
951 /* Bandwidth checking storage */
952 struct xhci_bw_info bw_info
;
953 struct list_head bw_endpoint_list
;
954 /* Isoch Frame ID checking storage */
956 /* Use new Isoch TRB layout needed for extended TBC support */
957 bool use_extended_tbc
;
960 enum xhci_overhead_type
{
961 LS_OVERHEAD_TYPE
= 0,
966 struct xhci_interval_bw
{
967 unsigned int num_packets
;
968 /* Sorted by max packet size.
969 * Head of the list is the greatest max packet size.
971 struct list_head endpoints
;
972 /* How many endpoints of each speed are present. */
973 unsigned int overhead
[3];
976 #define XHCI_MAX_INTERVAL 16
978 struct xhci_interval_bw_table
{
979 unsigned int interval0_esit_payload
;
980 struct xhci_interval_bw interval_bw
[XHCI_MAX_INTERVAL
];
981 /* Includes reserved bandwidth for async endpoints */
982 unsigned int bw_used
;
983 unsigned int ss_bw_in
;
984 unsigned int ss_bw_out
;
988 struct xhci_virt_device
{
989 struct usb_device
*udev
;
991 * Commands to the hardware are passed an "input context" that
992 * tells the hardware what to change in its data structures.
993 * The hardware will return changes in an "output context" that
994 * software must allocate for the hardware. We need to keep
995 * track of input and output contexts separately because
996 * these commands might fail and we don't trust the hardware.
998 struct xhci_container_ctx
*out_ctx
;
999 /* Used for addressing devices and configuration changes */
1000 struct xhci_container_ctx
*in_ctx
;
1001 struct xhci_virt_ep eps
[31];
1004 struct xhci_interval_bw_table
*bw_table
;
1005 struct xhci_tt_bw_info
*tt_info
;
1006 /* The current max exit latency for the enabled USB3 link states. */
1011 * For each roothub, keep track of the bandwidth information for each periodic
1014 * If a high speed hub is attached to the roothub, each TT associated with that
1015 * hub is a separate bandwidth domain. The interval information for the
1016 * endpoints on the devices under that TT will appear in the TT structure.
1018 struct xhci_root_port_bw_info
{
1019 struct list_head tts
;
1020 unsigned int num_active_tts
;
1021 struct xhci_interval_bw_table bw_table
;
1024 struct xhci_tt_bw_info
{
1025 struct list_head tt_list
;
1028 struct xhci_interval_bw_table bw_table
;
1034 * struct xhci_device_context_array
1035 * @dev_context_ptr array of 64-bit DMA addresses for device contexts
1037 struct xhci_device_context_array
{
1038 /* 64-bit device addresses; we only write 32-bit addresses */
1039 __le64 dev_context_ptrs
[MAX_HC_SLOTS
];
1040 /* private xHCD pointers */
1043 /* TODO: write function to set the 64-bit device DMA address */
1045 * TODO: change this to be dynamically sized at HC mem init time since the HC
1046 * might not be able to handle the maximum number of devices possible.
1050 struct xhci_transfer_event
{
1051 /* 64-bit buffer address, or immediate data */
1053 __le32 transfer_len
;
1054 /* This field is interpreted differently based on the type of TRB */
1058 /* Transfer event TRB length bit mask */
1060 #define EVENT_TRB_LEN(p) ((p) & 0xffffff)
1062 /** Transfer Event bit fields **/
1063 #define TRB_TO_EP_ID(p) (((p) >> 16) & 0x1f)
1065 /* Completion Code - only applicable for some types of TRBs */
1066 #define COMP_CODE_MASK (0xff << 24)
1067 #define GET_COMP_CODE(p) (((p) & COMP_CODE_MASK) >> 24)
1068 #define COMP_INVALID 0
1069 #define COMP_SUCCESS 1
1070 #define COMP_DATA_BUFFER_ERROR 2
1071 #define COMP_BABBLE_DETECTED_ERROR 3
1072 #define COMP_USB_TRANSACTION_ERROR 4
1073 #define COMP_TRB_ERROR 5
1074 #define COMP_STALL_ERROR 6
1075 #define COMP_RESOURCE_ERROR 7
1076 #define COMP_BANDWIDTH_ERROR 8
1077 #define COMP_NO_SLOTS_AVAILABLE_ERROR 9
1078 #define COMP_INVALID_STREAM_TYPE_ERROR 10
1079 #define COMP_SLOT_NOT_ENABLED_ERROR 11
1080 #define COMP_ENDPOINT_NOT_ENABLED_ERROR 12
1081 #define COMP_SHORT_PACKET 13
1082 #define COMP_RING_UNDERRUN 14
1083 #define COMP_RING_OVERRUN 15
1084 #define COMP_VF_EVENT_RING_FULL_ERROR 16
1085 #define COMP_PARAMETER_ERROR 17
1086 #define COMP_BANDWIDTH_OVERRUN_ERROR 18
1087 #define COMP_CONTEXT_STATE_ERROR 19
1088 #define COMP_NO_PING_RESPONSE_ERROR 20
1089 #define COMP_EVENT_RING_FULL_ERROR 21
1090 #define COMP_INCOMPATIBLE_DEVICE_ERROR 22
1091 #define COMP_MISSED_SERVICE_ERROR 23
1092 #define COMP_COMMAND_RING_STOPPED 24
1093 #define COMP_COMMAND_ABORTED 25
1094 #define COMP_STOPPED 26
1095 #define COMP_STOPPED_LENGTH_INVALID 27
1096 #define COMP_STOPPED_SHORT_PACKET 28
1097 #define COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR 29
1098 #define COMP_ISOCH_BUFFER_OVERRUN 31
1099 #define COMP_EVENT_LOST_ERROR 32
1100 #define COMP_UNDEFINED_ERROR 33
1101 #define COMP_INVALID_STREAM_ID_ERROR 34
1102 #define COMP_SECONDARY_BANDWIDTH_ERROR 35
1103 #define COMP_SPLIT_TRANSACTION_ERROR 36
1105 static inline const char *xhci_trb_comp_code_string(u8 status
)
1112 case COMP_DATA_BUFFER_ERROR
:
1113 return "Data Buffer Error";
1114 case COMP_BABBLE_DETECTED_ERROR
:
1115 return "Babble Detected";
1116 case COMP_USB_TRANSACTION_ERROR
:
1117 return "USB Transaction Error";
1118 case COMP_TRB_ERROR
:
1120 case COMP_STALL_ERROR
:
1121 return "Stall Error";
1122 case COMP_RESOURCE_ERROR
:
1123 return "Resource Error";
1124 case COMP_BANDWIDTH_ERROR
:
1125 return "Bandwidth Error";
1126 case COMP_NO_SLOTS_AVAILABLE_ERROR
:
1127 return "No Slots Available Error";
1128 case COMP_INVALID_STREAM_TYPE_ERROR
:
1129 return "Invalid Stream Type Error";
1130 case COMP_SLOT_NOT_ENABLED_ERROR
:
1131 return "Slot Not Enabled Error";
1132 case COMP_ENDPOINT_NOT_ENABLED_ERROR
:
1133 return "Endpoint Not Enabled Error";
1134 case COMP_SHORT_PACKET
:
1135 return "Short Packet";
1136 case COMP_RING_UNDERRUN
:
1137 return "Ring Underrun";
1138 case COMP_RING_OVERRUN
:
1139 return "Ring Overrun";
1140 case COMP_VF_EVENT_RING_FULL_ERROR
:
1141 return "VF Event Ring Full Error";
1142 case COMP_PARAMETER_ERROR
:
1143 return "Parameter Error";
1144 case COMP_BANDWIDTH_OVERRUN_ERROR
:
1145 return "Bandwidth Overrun Error";
1146 case COMP_CONTEXT_STATE_ERROR
:
1147 return "Context State Error";
1148 case COMP_NO_PING_RESPONSE_ERROR
:
1149 return "No Ping Response Error";
1150 case COMP_EVENT_RING_FULL_ERROR
:
1151 return "Event Ring Full Error";
1152 case COMP_INCOMPATIBLE_DEVICE_ERROR
:
1153 return "Incompatible Device Error";
1154 case COMP_MISSED_SERVICE_ERROR
:
1155 return "Missed Service Error";
1156 case COMP_COMMAND_RING_STOPPED
:
1157 return "Command Ring Stopped";
1158 case COMP_COMMAND_ABORTED
:
1159 return "Command Aborted";
1162 case COMP_STOPPED_LENGTH_INVALID
:
1163 return "Stopped - Length Invalid";
1164 case COMP_STOPPED_SHORT_PACKET
:
1165 return "Stopped - Short Packet";
1166 case COMP_MAX_EXIT_LATENCY_TOO_LARGE_ERROR
:
1167 return "Max Exit Latency Too Large Error";
1168 case COMP_ISOCH_BUFFER_OVERRUN
:
1169 return "Isoch Buffer Overrun";
1170 case COMP_EVENT_LOST_ERROR
:
1171 return "Event Lost Error";
1172 case COMP_UNDEFINED_ERROR
:
1173 return "Undefined Error";
1174 case COMP_INVALID_STREAM_ID_ERROR
:
1175 return "Invalid Stream ID Error";
1176 case COMP_SECONDARY_BANDWIDTH_ERROR
:
1177 return "Secondary Bandwidth Error";
1178 case COMP_SPLIT_TRANSACTION_ERROR
:
1179 return "Split Transaction Error";
1185 struct xhci_link_trb
{
1186 /* 64-bit segment pointer*/
1192 /* control bitfields */
1193 #define LINK_TOGGLE (0x1<<1)
1195 /* Command completion event TRB */
1196 struct xhci_event_cmd
{
1197 /* Pointer to command TRB, or the value passed by the event data trb */
1203 /* flags bitmasks */
1205 /* Address device - disable SetAddress */
1206 #define TRB_BSR (1<<9)
1208 /* Configure Endpoint - Deconfigure */
1209 #define TRB_DC (1<<9)
1211 /* Stop Ring - Transfer State Preserve */
1212 #define TRB_TSP (1<<9)
1214 enum xhci_ep_reset_type
{
1220 #define TRB_TO_VF_INTR_TARGET(p) (((p) & (0x3ff << 22)) >> 22)
1221 #define TRB_TO_VF_ID(p) (((p) & (0xff << 16)) >> 16)
1223 /* Set Latency Tolerance Value */
1224 #define TRB_TO_BELT(p) (((p) & (0xfff << 16)) >> 16)
1226 /* Get Port Bandwidth */
1227 #define TRB_TO_DEV_SPEED(p) (((p) & (0xf << 16)) >> 16)
1230 #define TRB_TO_PACKET_TYPE(p) ((p) & 0x1f)
1231 #define TRB_TO_ROOTHUB_PORT(p) (((p) & (0xff << 24)) >> 24)
1233 enum xhci_setup_dev
{
1235 SETUP_CONTEXT_ADDRESS
,
1238 /* bits 16:23 are the virtual function ID */
1239 /* bits 24:31 are the slot ID */
1240 #define TRB_TO_SLOT_ID(p) (((p) & (0xff<<24)) >> 24)
1241 #define SLOT_ID_FOR_TRB(p) (((p) & 0xff) << 24)
1243 /* Stop Endpoint TRB - ep_index to endpoint ID for this TRB */
1244 #define TRB_TO_EP_INDEX(p) ((((p) & (0x1f << 16)) >> 16) - 1)
1245 #define EP_ID_FOR_TRB(p) ((((p) + 1) & 0x1f) << 16)
1247 #define SUSPEND_PORT_FOR_TRB(p) (((p) & 1) << 23)
1248 #define TRB_TO_SUSPEND_PORT(p) (((p) & (1 << 23)) >> 23)
1249 #define LAST_EP_INDEX 30
1251 /* Set TR Dequeue Pointer command TRB fields, 6.4.3.9 */
1252 #define TRB_TO_STREAM_ID(p) ((((p) & (0xffff << 16)) >> 16))
1253 #define STREAM_ID_FOR_TRB(p) ((((p)) & 0xffff) << 16)
1254 #define SCT_FOR_TRB(p) (((p) << 1) & 0x7)
1256 /* Link TRB specific fields */
1257 #define TRB_TC (1<<1)
1259 /* Port Status Change Event TRB fields */
1260 /* Port ID - bits 31:24 */
1261 #define GET_PORT_ID(p) (((p) & (0xff << 24)) >> 24)
1263 #define EVENT_DATA (1 << 2)
1265 /* Normal TRB fields */
1266 /* transfer_len bitmasks - bits 0:16 */
1267 #define TRB_LEN(p) ((p) & 0x1ffff)
1268 /* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */
1269 #define TRB_TD_SIZE(p) (min((p), (u32)31) << 17)
1270 #define GET_TD_SIZE(p) (((p) & 0x3e0000) >> 17)
1271 /* xhci 1.1 uses the TD_SIZE field for TBC if Extended TBC is enabled (ETE) */
1272 #define TRB_TD_SIZE_TBC(p) (min((p), (u32)31) << 17)
1273 /* Interrupter Target - which MSI-X vector to target the completion event at */
1274 #define TRB_INTR_TARGET(p) (((p) & 0x3ff) << 22)
1275 #define GET_INTR_TARGET(p) (((p) >> 22) & 0x3ff)
1276 /* Total burst count field, Rsvdz on xhci 1.1 with Extended TBC enabled (ETE) */
1277 #define TRB_TBC(p) (((p) & 0x3) << 7)
1278 #define TRB_TLBPC(p) (((p) & 0xf) << 16)
1280 /* Cycle bit - indicates TRB ownership by HC or HCD */
1281 #define TRB_CYCLE (1<<0)
1283 * Force next event data TRB to be evaluated before task switch.
1284 * Used to pass OS data back after a TD completes.
1286 #define TRB_ENT (1<<1)
1287 /* Interrupt on short packet */
1288 #define TRB_ISP (1<<2)
1289 /* Set PCIe no snoop attribute */
1290 #define TRB_NO_SNOOP (1<<3)
1291 /* Chain multiple TRBs into a TD */
1292 #define TRB_CHAIN (1<<4)
1293 /* Interrupt on completion */
1294 #define TRB_IOC (1<<5)
1295 /* The buffer pointer contains immediate data */
1296 #define TRB_IDT (1<<6)
1298 /* Block Event Interrupt */
1299 #define TRB_BEI (1<<9)
1301 /* Control transfer TRB specific fields */
1302 #define TRB_DIR_IN (1<<16)
1303 #define TRB_TX_TYPE(p) ((p) << 16)
1304 #define TRB_DATA_OUT 2
1305 #define TRB_DATA_IN 3
1307 /* Isochronous TRB specific fields */
1308 #define TRB_SIA (1<<31)
1309 #define TRB_FRAME_ID(p) (((p) & 0x7ff) << 20)
1311 struct xhci_generic_trb
{
1316 struct xhci_link_trb link
;
1317 struct xhci_transfer_event trans_event
;
1318 struct xhci_event_cmd event_cmd
;
1319 struct xhci_generic_trb generic
;
1323 #define TRB_TYPE_BITMASK (0xfc00)
1324 #define TRB_TYPE(p) ((p) << 10)
1325 #define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
1327 /* bulk, interrupt, isoc scatter/gather, and control data stage */
1328 #define TRB_NORMAL 1
1329 /* setup stage for control transfers */
1331 /* data stage for control transfers */
1333 /* status stage for control transfers */
1334 #define TRB_STATUS 4
1335 /* isoc transfers */
1337 /* TRB for linking ring segments */
1339 #define TRB_EVENT_DATA 7
1340 /* Transfer Ring No-op (not for the command ring) */
1341 #define TRB_TR_NOOP 8
1343 /* Enable Slot Command */
1344 #define TRB_ENABLE_SLOT 9
1345 /* Disable Slot Command */
1346 #define TRB_DISABLE_SLOT 10
1347 /* Address Device Command */
1348 #define TRB_ADDR_DEV 11
1349 /* Configure Endpoint Command */
1350 #define TRB_CONFIG_EP 12
1351 /* Evaluate Context Command */
1352 #define TRB_EVAL_CONTEXT 13
1353 /* Reset Endpoint Command */
1354 #define TRB_RESET_EP 14
1355 /* Stop Transfer Ring Command */
1356 #define TRB_STOP_RING 15
1357 /* Set Transfer Ring Dequeue Pointer Command */
1358 #define TRB_SET_DEQ 16
1359 /* Reset Device Command */
1360 #define TRB_RESET_DEV 17
1361 /* Force Event Command (opt) */
1362 #define TRB_FORCE_EVENT 18
1363 /* Negotiate Bandwidth Command (opt) */
1364 #define TRB_NEG_BANDWIDTH 19
1365 /* Set Latency Tolerance Value Command (opt) */
1366 #define TRB_SET_LT 20
1367 /* Get port bandwidth Command */
1368 #define TRB_GET_BW 21
1369 /* Force Header Command - generate a transaction or link management packet */
1370 #define TRB_FORCE_HEADER 22
1371 /* No-op Command - not for transfer rings */
1372 #define TRB_CMD_NOOP 23
1373 /* TRB IDs 24-31 reserved */
1375 /* Transfer Event */
1376 #define TRB_TRANSFER 32
1377 /* Command Completion Event */
1378 #define TRB_COMPLETION 33
1379 /* Port Status Change Event */
1380 #define TRB_PORT_STATUS 34
1381 /* Bandwidth Request Event (opt) */
1382 #define TRB_BANDWIDTH_EVENT 35
1383 /* Doorbell Event (opt) */
1384 #define TRB_DOORBELL 36
1385 /* Host Controller Event */
1386 #define TRB_HC_EVENT 37
1387 /* Device Notification Event - device sent function wake notification */
1388 #define TRB_DEV_NOTE 38
1389 /* MFINDEX Wrap Event - microframe counter wrapped */
1390 #define TRB_MFINDEX_WRAP 39
1391 /* TRB IDs 40-47 reserved, 48-63 is vendor-defined */
1393 /* Nec vendor-specific command completion event. */
1394 #define TRB_NEC_CMD_COMP 48
1395 /* Get NEC firmware revision. */
1396 #define TRB_NEC_GET_FW 49
1398 static inline const char *xhci_trb_type_string(u8 type
)
1404 return "Setup Stage";
1406 return "Data Stage";
1408 return "Status Stage";
1413 case TRB_EVENT_DATA
:
1414 return "Event Data";
1417 case TRB_ENABLE_SLOT
:
1418 return "Enable Slot Command";
1419 case TRB_DISABLE_SLOT
:
1420 return "Disable Slot Command";
1422 return "Address Device Command";
1424 return "Configure Endpoint Command";
1425 case TRB_EVAL_CONTEXT
:
1426 return "Evaluate Context Command";
1428 return "Reset Endpoint Command";
1430 return "Stop Ring Command";
1432 return "Set TR Dequeue Pointer Command";
1434 return "Reset Device Command";
1435 case TRB_FORCE_EVENT
:
1436 return "Force Event Command";
1437 case TRB_NEG_BANDWIDTH
:
1438 return "Negotiate Bandwidth Command";
1440 return "Set Latency Tolerance Value Command";
1442 return "Get Port Bandwidth Command";
1443 case TRB_FORCE_HEADER
:
1444 return "Force Header Command";
1446 return "No-Op Command";
1448 return "Transfer Event";
1449 case TRB_COMPLETION
:
1450 return "Command Completion Event";
1451 case TRB_PORT_STATUS
:
1452 return "Port Status Change Event";
1453 case TRB_BANDWIDTH_EVENT
:
1454 return "Bandwidth Request Event";
1456 return "Doorbell Event";
1458 return "Host Controller Event";
1460 return "Device Notification Event";
1461 case TRB_MFINDEX_WRAP
:
1462 return "MFINDEX Wrap Event";
1463 case TRB_NEC_CMD_COMP
:
1464 return "NEC Command Completion Event";
1465 case TRB_NEC_GET_FW
:
1466 return "NET Get Firmware Revision Command";
1472 #define TRB_TYPE_LINK(x) (((x) & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK))
1473 /* Above, but for __le32 types -- can avoid work by swapping constants: */
1474 #define TRB_TYPE_LINK_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
1475 cpu_to_le32(TRB_TYPE(TRB_LINK)))
1476 #define TRB_TYPE_NOOP_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
1477 cpu_to_le32(TRB_TYPE(TRB_TR_NOOP)))
1479 #define NEC_FW_MINOR(p) (((p) >> 0) & 0xff)
1480 #define NEC_FW_MAJOR(p) (((p) >> 8) & 0xff)
1483 * TRBS_PER_SEGMENT must be a multiple of 4,
1484 * since the command ring is 64-byte aligned.
1485 * It must also be greater than 16.
1487 #define TRBS_PER_SEGMENT 256
1488 /* Allow two commands + a link TRB, along with any reserved command TRBs */
1489 #define MAX_RSVD_CMD_TRBS (TRBS_PER_SEGMENT - 3)
1490 #define TRB_SEGMENT_SIZE (TRBS_PER_SEGMENT*16)
1491 #define TRB_SEGMENT_SHIFT (ilog2(TRB_SEGMENT_SIZE))
1492 /* TRB buffer pointers can't cross 64KB boundaries */
1493 #define TRB_MAX_BUFF_SHIFT 16
1494 #define TRB_MAX_BUFF_SIZE (1 << TRB_MAX_BUFF_SHIFT)
1495 /* How much data is left before the 64KB boundary? */
1496 #define TRB_BUFF_LEN_UP_TO_BOUNDARY(addr) (TRB_MAX_BUFF_SIZE - \
1497 (addr & (TRB_MAX_BUFF_SIZE - 1)))
1499 struct xhci_segment
{
1500 union xhci_trb
*trbs
;
1501 /* private to HCD */
1502 struct xhci_segment
*next
;
1504 /* Max packet sized bounce buffer for td-fragmant alignment */
1505 dma_addr_t bounce_dma
;
1507 unsigned int bounce_offs
;
1508 unsigned int bounce_len
;
1512 struct list_head td_list
;
1513 struct list_head cancelled_td_list
;
1515 struct xhci_segment
*start_seg
;
1516 union xhci_trb
*first_trb
;
1517 union xhci_trb
*last_trb
;
1518 struct xhci_segment
*bounce_seg
;
1519 /* actual_length of the URB has already been set */
1520 bool urb_length_set
;
1523 /* xHCI command default timeout value */
1524 #define XHCI_CMD_DEFAULT_TIMEOUT (5 * HZ)
1526 /* command descriptor */
1528 struct xhci_command
*command
;
1529 union xhci_trb
*cmd_trb
;
1532 struct xhci_dequeue_state
{
1533 struct xhci_segment
*new_deq_seg
;
1534 union xhci_trb
*new_deq_ptr
;
1535 int new_cycle_state
;
1536 unsigned int stream_id
;
1539 enum xhci_ring_type
{
1549 static inline const char *xhci_ring_type_string(enum xhci_ring_type type
)
1572 struct xhci_segment
*first_seg
;
1573 struct xhci_segment
*last_seg
;
1574 union xhci_trb
*enqueue
;
1575 struct xhci_segment
*enq_seg
;
1576 union xhci_trb
*dequeue
;
1577 struct xhci_segment
*deq_seg
;
1578 struct list_head td_list
;
1580 * Write the cycle state into the TRB cycle field to give ownership of
1581 * the TRB to the host controller (if we are the producer), or to check
1582 * if we own the TRB (if we are the consumer). See section 4.9.1.
1585 unsigned int stream_id
;
1586 unsigned int num_segs
;
1587 unsigned int num_trbs_free
;
1588 unsigned int num_trbs_free_temp
;
1589 unsigned int bounce_buf_len
;
1590 enum xhci_ring_type type
;
1591 bool last_td_was_short
;
1592 struct radix_tree_root
*trb_address_map
;
1595 struct xhci_erst_entry
{
1596 /* 64-bit event ring segment address */
1604 struct xhci_erst_entry
*entries
;
1605 unsigned int num_entries
;
1606 /* xhci->event_ring keeps track of segment dma addresses */
1607 dma_addr_t erst_dma_addr
;
1608 /* Num entries the ERST can contain */
1609 unsigned int erst_size
;
1612 struct xhci_scratchpad
{
1621 struct xhci_td td
[0];
1625 * Each segment table entry is 4*32bits long. 1K seems like an ok size:
1626 * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table,
1627 * meaning 64 ring segments.
1628 * Initial allocated size of the ERST, in number of entries */
1629 #define ERST_NUM_SEGS 1
1630 /* Initial allocated size of the ERST, in number of entries */
1631 #define ERST_SIZE 64
1632 /* Initial number of event segment rings allocated */
1633 #define ERST_ENTRIES 1
1634 /* Poll every 60 seconds */
1635 #define POLL_TIMEOUT 60
1636 /* Stop endpoint command timeout (secs) for URB cancellation watchdog timer */
1637 #define XHCI_STOP_EP_CMD_TIMEOUT 5
1638 /* XXX: Make these module parameters */
1655 struct list_head list
;
1658 struct xhci_bus_state
{
1659 unsigned long bus_suspended
;
1660 unsigned long next_statechange
;
1662 /* Port suspend arrays are indexed by the portnum of the fake roothub */
1663 /* ports suspend status arrays - max 31 ports for USB2, 15 for USB3 */
1665 u32 suspended_ports
;
1666 u32 port_remote_wakeup
;
1667 unsigned long resume_done
[USB_MAXCHILDREN
];
1668 /* which ports have started to resume */
1669 unsigned long resuming_ports
;
1670 /* Which ports are waiting on RExit to U0 transition. */
1671 unsigned long rexit_ports
;
1672 struct completion rexit_done
[USB_MAXCHILDREN
];
1677 * It can take up to 20 ms to transition from RExit to U0 on the
1678 * Intel Lynx Point LP xHCI host.
1680 #define XHCI_MAX_REXIT_TIMEOUT (20 * 1000)
1682 static inline unsigned int hcd_index(struct usb_hcd
*hcd
)
1684 if (hcd
->speed
== HCD_USB3
)
1693 u32
*psi
; /* array of protocol speed ID entries */
1698 /* There is one xhci_hcd structure per controller */
1700 struct usb_hcd
*main_hcd
;
1701 struct usb_hcd
*shared_hcd
;
1702 /* glue to PCI and HCD framework */
1703 struct xhci_cap_regs __iomem
*cap_regs
;
1704 struct xhci_op_regs __iomem
*op_regs
;
1705 struct xhci_run_regs __iomem
*run_regs
;
1706 struct xhci_doorbell_array __iomem
*dba
;
1707 /* Our HCD's current interrupter register set */
1708 struct xhci_intr_reg __iomem
*ir_set
;
1710 /* Cached register copies of read-only HC data */
1719 /* packed release number */
1723 u8 max_interrupters
;
1727 /* 4KB min, 128MB max */
1729 /* Valid values are 12 to 20, inclusive */
1733 /* optional clock */
1735 /* data structures */
1736 struct xhci_device_context_array
*dcbaa
;
1737 struct xhci_ring
*cmd_ring
;
1738 unsigned int cmd_ring_state
;
1739 #define CMD_RING_STATE_RUNNING (1 << 0)
1740 #define CMD_RING_STATE_ABORTED (1 << 1)
1741 #define CMD_RING_STATE_STOPPED (1 << 2)
1742 struct list_head cmd_list
;
1743 unsigned int cmd_ring_reserved_trbs
;
1744 struct delayed_work cmd_timer
;
1745 struct completion cmd_ring_stop_completion
;
1746 struct xhci_command
*current_cmd
;
1747 struct xhci_ring
*event_ring
;
1748 struct xhci_erst erst
;
1750 struct xhci_scratchpad
*scratchpad
;
1751 /* Store LPM test failed devices' information */
1752 struct list_head lpm_failed_devs
;
1754 /* slot enabling and address device helpers */
1755 /* these are not thread safe so use mutex */
1757 /* For USB 3.0 LPM enable/disable. */
1758 struct xhci_command
*lpm_command
;
1759 /* Internal mirror of the HW's dcbaa */
1760 struct xhci_virt_device
*devs
[MAX_HC_SLOTS
];
1761 /* For keeping track of bandwidth domains per roothub. */
1762 struct xhci_root_port_bw_info
*rh_bw
;
1765 struct dma_pool
*device_pool
;
1766 struct dma_pool
*segment_pool
;
1767 struct dma_pool
*small_streams_pool
;
1768 struct dma_pool
*medium_streams_pool
;
1770 /* Host controller watchdog timer structures */
1771 unsigned int xhc_state
;
1775 /* Host controller is dying - not responding to commands. "I'm not dead yet!"
1777 * xHC interrupts have been disabled and a watchdog timer will (or has already)
1778 * halt the xHCI host, and complete all URBs with an -ESHUTDOWN code. Any code
1779 * that sees this status (other than the timer that set it) should stop touching
1780 * hardware immediately. Interrupt handlers should return immediately when
1781 * they see this status (any time they drop and re-acquire xhci->lock).
1782 * xhci_urb_dequeue() should call usb_hcd_check_unlink_urb() and return without
1783 * putting the TD on the canceled list, etc.
1785 * There are no reports of xHCI host controllers that display this issue.
1787 #define XHCI_STATE_DYING (1 << 0)
1788 #define XHCI_STATE_HALTED (1 << 1)
1789 #define XHCI_STATE_REMOVING (1 << 2)
1790 unsigned int quirks
;
1791 #define XHCI_LINK_TRB_QUIRK (1 << 0)
1792 #define XHCI_RESET_EP_QUIRK (1 << 1)
1793 #define XHCI_NEC_HOST (1 << 2)
1794 #define XHCI_AMD_PLL_FIX (1 << 3)
1795 #define XHCI_SPURIOUS_SUCCESS (1 << 4)
1797 * Certain Intel host controllers have a limit to the number of endpoint
1798 * contexts they can handle. Ideally, they would signal that they can't handle
1799 * anymore endpoint contexts by returning a Resource Error for the Configure
1800 * Endpoint command, but they don't. Instead they expect software to keep track
1801 * of the number of active endpoints for them, across configure endpoint
1802 * commands, reset device commands, disable slot commands, and address device
1805 #define XHCI_EP_LIMIT_QUIRK (1 << 5)
1806 #define XHCI_BROKEN_MSI (1 << 6)
1807 #define XHCI_RESET_ON_RESUME (1 << 7)
1808 #define XHCI_SW_BW_CHECKING (1 << 8)
1809 #define XHCI_AMD_0x96_HOST (1 << 9)
1810 #define XHCI_TRUST_TX_LENGTH (1 << 10)
1811 #define XHCI_LPM_SUPPORT (1 << 11)
1812 #define XHCI_INTEL_HOST (1 << 12)
1813 #define XHCI_SPURIOUS_REBOOT (1 << 13)
1814 #define XHCI_COMP_MODE_QUIRK (1 << 14)
1815 #define XHCI_AVOID_BEI (1 << 15)
1816 #define XHCI_PLAT (1 << 16)
1817 #define XHCI_SLOW_SUSPEND (1 << 17)
1818 #define XHCI_SPURIOUS_WAKEUP (1 << 18)
1819 /* For controllers with a broken beyond repair streams implementation */
1820 #define XHCI_BROKEN_STREAMS (1 << 19)
1821 #define XHCI_PME_STUCK_QUIRK (1 << 20)
1822 #define XHCI_MTK_HOST (1 << 21)
1823 #define XHCI_SSIC_PORT_UNUSED (1 << 22)
1824 #define XHCI_NO_64BIT_SUPPORT (1 << 23)
1825 #define XHCI_MISSING_CAS (1 << 24)
1826 /* For controller with a broken Port Disable implementation */
1827 #define XHCI_BROKEN_PORT_PED (1 << 25)
1828 #define XHCI_LIMIT_ENDPOINT_INTERVAL_7 (1 << 26)
1829 #define XHCI_U2_DISABLE_WAKE (1 << 27)
1830 #define XHCI_ASMEDIA_MODIFY_FLOWCONTROL (1 << 28)
1832 unsigned int num_active_eps
;
1833 unsigned int limit_active_eps
;
1834 /* There are two roothubs to keep track of bus suspend info for */
1835 struct xhci_bus_state bus_state
[2];
1836 /* Is each xHCI roothub port a USB 3.0, USB 2.0, or USB 1.1 port? */
1838 /* Array of pointers to USB 3.0 PORTSC registers */
1839 __le32 __iomem
**usb3_ports
;
1840 unsigned int num_usb3_ports
;
1841 /* Array of pointers to USB 2.0 PORTSC registers */
1842 __le32 __iomem
**usb2_ports
;
1843 struct xhci_hub usb2_rhub
;
1844 struct xhci_hub usb3_rhub
;
1845 unsigned int num_usb2_ports
;
1846 /* support xHCI 0.96 spec USB2 software LPM */
1847 unsigned sw_lpm_support
:1;
1848 /* support xHCI 1.0 spec USB2 hardware LPM */
1849 unsigned hw_lpm_support
:1;
1850 /* cached usb2 extened protocol capabilites */
1852 unsigned int num_ext_caps
;
1853 /* Compliance Mode Recovery Data */
1854 struct timer_list comp_mode_recovery_timer
;
1857 /* Compliance Mode Timer Triggered every 2 seconds */
1858 #define COMP_MODE_RCVRY_MSECS 2000
1860 /* platform-specific data -- must come last */
1861 unsigned long priv
[0] __aligned(sizeof(s64
));
1864 /* Platform specific overrides to generic XHCI hc_driver ops */
1865 struct xhci_driver_overrides
{
1866 size_t extra_priv_size
;
1867 int (*reset
)(struct usb_hcd
*hcd
);
1868 int (*start
)(struct usb_hcd
*hcd
);
1871 #define XHCI_CFC_DELAY 10
1873 /* convert between an HCD pointer and the corresponding EHCI_HCD */
1874 static inline struct xhci_hcd
*hcd_to_xhci(struct usb_hcd
*hcd
)
1876 struct usb_hcd
*primary_hcd
;
1878 if (usb_hcd_is_primary_hcd(hcd
))
1881 primary_hcd
= hcd
->primary_hcd
;
1883 return (struct xhci_hcd
*) (primary_hcd
->hcd_priv
);
1886 static inline struct usb_hcd
*xhci_to_hcd(struct xhci_hcd
*xhci
)
1888 return xhci
->main_hcd
;
1891 #define xhci_dbg(xhci, fmt, args...) \
1892 dev_dbg(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1893 #define xhci_err(xhci, fmt, args...) \
1894 dev_err(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1895 #define xhci_warn(xhci, fmt, args...) \
1896 dev_warn(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1897 #define xhci_warn_ratelimited(xhci, fmt, args...) \
1898 dev_warn_ratelimited(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1899 #define xhci_info(xhci, fmt, args...) \
1900 dev_info(xhci_to_hcd(xhci)->self.controller , fmt , ## args)
1903 * Registers should always be accessed with double word or quad word accesses.
1905 * Some xHCI implementations may support 64-bit address pointers. Registers
1906 * with 64-bit address pointers should be written to with dword accesses by
1907 * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
1908 * xHCI implementations that do not support 64-bit address pointers will ignore
1909 * the high dword, and write order is irrelevant.
1911 static inline u64
xhci_read_64(const struct xhci_hcd
*xhci
,
1912 __le64 __iomem
*regs
)
1914 return lo_hi_readq(regs
);
1916 static inline void xhci_write_64(struct xhci_hcd
*xhci
,
1917 const u64 val
, __le64 __iomem
*regs
)
1919 lo_hi_writeq(val
, regs
);
1922 static inline int xhci_link_trb_quirk(struct xhci_hcd
*xhci
)
1924 return xhci
->quirks
& XHCI_LINK_TRB_QUIRK
;
1927 /* xHCI debugging */
1928 void xhci_print_ir_set(struct xhci_hcd
*xhci
, int set_num
);
1929 void xhci_print_registers(struct xhci_hcd
*xhci
);
1930 void xhci_dbg_regs(struct xhci_hcd
*xhci
);
1931 void xhci_print_run_regs(struct xhci_hcd
*xhci
);
1932 void xhci_dbg_erst(struct xhci_hcd
*xhci
, struct xhci_erst
*erst
);
1933 void xhci_dbg_cmd_ptrs(struct xhci_hcd
*xhci
);
1934 char *xhci_get_slot_state(struct xhci_hcd
*xhci
,
1935 struct xhci_container_ctx
*ctx
);
1936 void xhci_dbg_trace(struct xhci_hcd
*xhci
, void (*trace
)(struct va_format
*),
1937 const char *fmt
, ...);
1939 /* xHCI memory management */
1940 void xhci_mem_cleanup(struct xhci_hcd
*xhci
);
1941 int xhci_mem_init(struct xhci_hcd
*xhci
, gfp_t flags
);
1942 void xhci_free_virt_device(struct xhci_hcd
*xhci
, int slot_id
);
1943 int xhci_alloc_virt_device(struct xhci_hcd
*xhci
, int slot_id
, struct usb_device
*udev
, gfp_t flags
);
1944 int xhci_setup_addressable_virt_dev(struct xhci_hcd
*xhci
, struct usb_device
*udev
);
1945 void xhci_copy_ep0_dequeue_into_input_ctx(struct xhci_hcd
*xhci
,
1946 struct usb_device
*udev
);
1947 unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor
*desc
);
1948 unsigned int xhci_get_endpoint_address(unsigned int ep_index
);
1949 unsigned int xhci_last_valid_endpoint(u32 added_ctxs
);
1950 void xhci_endpoint_zero(struct xhci_hcd
*xhci
, struct xhci_virt_device
*virt_dev
, struct usb_host_endpoint
*ep
);
1951 void xhci_update_tt_active_eps(struct xhci_hcd
*xhci
,
1952 struct xhci_virt_device
*virt_dev
,
1953 int old_active_eps
);
1954 void xhci_clear_endpoint_bw_info(struct xhci_bw_info
*bw_info
);
1955 void xhci_update_bw_info(struct xhci_hcd
*xhci
,
1956 struct xhci_container_ctx
*in_ctx
,
1957 struct xhci_input_control_ctx
*ctrl_ctx
,
1958 struct xhci_virt_device
*virt_dev
);
1959 void xhci_endpoint_copy(struct xhci_hcd
*xhci
,
1960 struct xhci_container_ctx
*in_ctx
,
1961 struct xhci_container_ctx
*out_ctx
,
1962 unsigned int ep_index
);
1963 void xhci_slot_copy(struct xhci_hcd
*xhci
,
1964 struct xhci_container_ctx
*in_ctx
,
1965 struct xhci_container_ctx
*out_ctx
);
1966 int xhci_endpoint_init(struct xhci_hcd
*xhci
, struct xhci_virt_device
*virt_dev
,
1967 struct usb_device
*udev
, struct usb_host_endpoint
*ep
,
1969 void xhci_ring_free(struct xhci_hcd
*xhci
, struct xhci_ring
*ring
);
1970 int xhci_ring_expansion(struct xhci_hcd
*xhci
, struct xhci_ring
*ring
,
1971 unsigned int num_trbs
, gfp_t flags
);
1972 void xhci_free_endpoint_ring(struct xhci_hcd
*xhci
,
1973 struct xhci_virt_device
*virt_dev
,
1974 unsigned int ep_index
);
1975 struct xhci_stream_info
*xhci_alloc_stream_info(struct xhci_hcd
*xhci
,
1976 unsigned int num_stream_ctxs
,
1977 unsigned int num_streams
,
1978 unsigned int max_packet
, gfp_t flags
);
1979 void xhci_free_stream_info(struct xhci_hcd
*xhci
,
1980 struct xhci_stream_info
*stream_info
);
1981 void xhci_setup_streams_ep_input_ctx(struct xhci_hcd
*xhci
,
1982 struct xhci_ep_ctx
*ep_ctx
,
1983 struct xhci_stream_info
*stream_info
);
1984 void xhci_setup_no_streams_ep_input_ctx(struct xhci_ep_ctx
*ep_ctx
,
1985 struct xhci_virt_ep
*ep
);
1986 void xhci_free_device_endpoint_resources(struct xhci_hcd
*xhci
,
1987 struct xhci_virt_device
*virt_dev
, bool drop_control_ep
);
1988 struct xhci_ring
*xhci_dma_to_transfer_ring(
1989 struct xhci_virt_ep
*ep
,
1991 struct xhci_ring
*xhci_stream_id_to_ring(
1992 struct xhci_virt_device
*dev
,
1993 unsigned int ep_index
,
1994 unsigned int stream_id
);
1995 struct xhci_command
*xhci_alloc_command(struct xhci_hcd
*xhci
,
1996 bool allocate_in_ctx
, bool allocate_completion
,
1998 void xhci_urb_free_priv(struct urb_priv
*urb_priv
);
1999 void xhci_free_command(struct xhci_hcd
*xhci
,
2000 struct xhci_command
*command
);
2002 /* xHCI host controller glue */
2003 typedef void (*xhci_get_quirks_t
)(struct device
*, struct xhci_hcd
*);
2004 int xhci_handshake(void __iomem
*ptr
, u32 mask
, u32 done
, int usec
);
2005 void xhci_quiesce(struct xhci_hcd
*xhci
);
2006 int xhci_halt(struct xhci_hcd
*xhci
);
2007 int xhci_start(struct xhci_hcd
*xhci
);
2008 int xhci_reset(struct xhci_hcd
*xhci
);
2009 int xhci_run(struct usb_hcd
*hcd
);
2010 int xhci_gen_setup(struct usb_hcd
*hcd
, xhci_get_quirks_t get_quirks
);
2011 void xhci_init_driver(struct hc_driver
*drv
,
2012 const struct xhci_driver_overrides
*over
);
2013 int xhci_disable_slot(struct xhci_hcd
*xhci
,
2014 struct xhci_command
*command
, u32 slot_id
);
2016 int xhci_suspend(struct xhci_hcd
*xhci
, bool do_wakeup
);
2017 int xhci_resume(struct xhci_hcd
*xhci
, bool hibernated
);
2019 irqreturn_t
xhci_irq(struct usb_hcd
*hcd
);
2020 irqreturn_t
xhci_msi_irq(int irq
, void *hcd
);
2021 int xhci_alloc_dev(struct usb_hcd
*hcd
, struct usb_device
*udev
);
2022 int xhci_alloc_tt_info(struct xhci_hcd
*xhci
,
2023 struct xhci_virt_device
*virt_dev
,
2024 struct usb_device
*hdev
,
2025 struct usb_tt
*tt
, gfp_t mem_flags
);
2027 /* xHCI ring, segment, TRB, and TD functions */
2028 dma_addr_t
xhci_trb_virt_to_dma(struct xhci_segment
*seg
, union xhci_trb
*trb
);
2029 struct xhci_segment
*trb_in_td(struct xhci_hcd
*xhci
,
2030 struct xhci_segment
*start_seg
, union xhci_trb
*start_trb
,
2031 union xhci_trb
*end_trb
, dma_addr_t suspect_dma
, bool debug
);
2032 int xhci_is_vendor_info_code(struct xhci_hcd
*xhci
, unsigned int trb_comp_code
);
2033 void xhci_ring_cmd_db(struct xhci_hcd
*xhci
);
2034 int xhci_queue_slot_control(struct xhci_hcd
*xhci
, struct xhci_command
*cmd
,
2035 u32 trb_type
, u32 slot_id
);
2036 int xhci_queue_address_device(struct xhci_hcd
*xhci
, struct xhci_command
*cmd
,
2037 dma_addr_t in_ctx_ptr
, u32 slot_id
, enum xhci_setup_dev
);
2038 int xhci_queue_vendor_command(struct xhci_hcd
*xhci
, struct xhci_command
*cmd
,
2039 u32 field1
, u32 field2
, u32 field3
, u32 field4
);
2040 int xhci_queue_stop_endpoint(struct xhci_hcd
*xhci
, struct xhci_command
*cmd
,
2041 int slot_id
, unsigned int ep_index
, int suspend
);
2042 int xhci_queue_ctrl_tx(struct xhci_hcd
*xhci
, gfp_t mem_flags
, struct urb
*urb
,
2043 int slot_id
, unsigned int ep_index
);
2044 int xhci_queue_bulk_tx(struct xhci_hcd
*xhci
, gfp_t mem_flags
, struct urb
*urb
,
2045 int slot_id
, unsigned int ep_index
);
2046 int xhci_queue_intr_tx(struct xhci_hcd
*xhci
, gfp_t mem_flags
, struct urb
*urb
,
2047 int slot_id
, unsigned int ep_index
);
2048 int xhci_queue_isoc_tx_prepare(struct xhci_hcd
*xhci
, gfp_t mem_flags
,
2049 struct urb
*urb
, int slot_id
, unsigned int ep_index
);
2050 int xhci_queue_configure_endpoint(struct xhci_hcd
*xhci
,
2051 struct xhci_command
*cmd
, dma_addr_t in_ctx_ptr
, u32 slot_id
,
2052 bool command_must_succeed
);
2053 int xhci_queue_evaluate_context(struct xhci_hcd
*xhci
, struct xhci_command
*cmd
,
2054 dma_addr_t in_ctx_ptr
, u32 slot_id
, bool command_must_succeed
);
2055 int xhci_queue_reset_ep(struct xhci_hcd
*xhci
, struct xhci_command
*cmd
,
2056 int slot_id
, unsigned int ep_index
,
2057 enum xhci_ep_reset_type reset_type
);
2058 int xhci_queue_reset_device(struct xhci_hcd
*xhci
, struct xhci_command
*cmd
,
2060 void xhci_find_new_dequeue_state(struct xhci_hcd
*xhci
,
2061 unsigned int slot_id
, unsigned int ep_index
,
2062 unsigned int stream_id
, struct xhci_td
*cur_td
,
2063 struct xhci_dequeue_state
*state
);
2064 void xhci_queue_new_dequeue_state(struct xhci_hcd
*xhci
,
2065 unsigned int slot_id
, unsigned int ep_index
,
2066 struct xhci_dequeue_state
*deq_state
);
2067 void xhci_cleanup_stalled_ring(struct xhci_hcd
*xhci
, unsigned int ep_index
,
2068 unsigned int stream_id
, struct xhci_td
*td
);
2069 void xhci_stop_endpoint_command_watchdog(unsigned long arg
);
2070 void xhci_handle_command_timeout(struct work_struct
*work
);
2072 void xhci_ring_ep_doorbell(struct xhci_hcd
*xhci
, unsigned int slot_id
,
2073 unsigned int ep_index
, unsigned int stream_id
);
2074 void xhci_cleanup_command_queue(struct xhci_hcd
*xhci
);
2076 /* xHCI roothub code */
2077 void xhci_set_link_state(struct xhci_hcd
*xhci
, __le32 __iomem
**port_array
,
2078 int port_id
, u32 link_state
);
2079 void xhci_test_and_clear_bit(struct xhci_hcd
*xhci
, __le32 __iomem
**port_array
,
2080 int port_id
, u32 port_bit
);
2081 int xhci_hub_control(struct usb_hcd
*hcd
, u16 typeReq
, u16 wValue
, u16 wIndex
,
2082 char *buf
, u16 wLength
);
2083 int xhci_hub_status_data(struct usb_hcd
*hcd
, char *buf
);
2084 int xhci_find_raw_port_number(struct usb_hcd
*hcd
, int port1
);
2085 void xhci_hc_died(struct xhci_hcd
*xhci
);
2088 int xhci_bus_suspend(struct usb_hcd
*hcd
);
2089 int xhci_bus_resume(struct usb_hcd
*hcd
);
2091 #define xhci_bus_suspend NULL
2092 #define xhci_bus_resume NULL
2093 #endif /* CONFIG_PM */
2095 u32
xhci_port_state_to_neutral(u32 state
);
2096 int xhci_find_slot_id_by_port(struct usb_hcd
*hcd
, struct xhci_hcd
*xhci
,
2098 void xhci_ring_device(struct xhci_hcd
*xhci
, int slot_id
);
2101 struct xhci_input_control_ctx
*xhci_get_input_control_ctx(struct xhci_container_ctx
*ctx
);
2102 struct xhci_slot_ctx
*xhci_get_slot_ctx(struct xhci_hcd
*xhci
, struct xhci_container_ctx
*ctx
);
2103 struct xhci_ep_ctx
*xhci_get_ep_ctx(struct xhci_hcd
*xhci
, struct xhci_container_ctx
*ctx
, unsigned int ep_index
);
2105 struct xhci_ring
*xhci_triad_to_transfer_ring(struct xhci_hcd
*xhci
,
2106 unsigned int slot_id
, unsigned int ep_index
,
2107 unsigned int stream_id
);
2108 static inline struct xhci_ring
*xhci_urb_to_transfer_ring(struct xhci_hcd
*xhci
,
2111 return xhci_triad_to_transfer_ring(xhci
, urb
->dev
->slot_id
,
2112 xhci_get_endpoint_index(&urb
->ep
->desc
),
2116 static inline char *xhci_slot_state_string(u32 state
)
2119 case SLOT_STATE_ENABLED
:
2120 return "enabled/disabled";
2121 case SLOT_STATE_DEFAULT
:
2123 case SLOT_STATE_ADDRESSED
:
2125 case SLOT_STATE_CONFIGURED
:
2126 return "configured";
2132 static inline const char *xhci_decode_trb(u32 field0
, u32 field1
, u32 field2
,
2135 static char str
[256];
2136 int type
= TRB_FIELD_TO_TYPE(field3
);
2141 "LINK %08x%08x intr %d type '%s' flags %c:%c:%c:%c",
2142 field1
, field0
, GET_INTR_TARGET(field2
),
2143 xhci_trb_type_string(type
),
2144 field3
& TRB_IOC
? 'I' : 'i',
2145 field3
& TRB_CHAIN
? 'C' : 'c',
2146 field3
& TRB_TC
? 'T' : 't',
2147 field3
& TRB_CYCLE
? 'C' : 'c');
2150 case TRB_COMPLETION
:
2151 case TRB_PORT_STATUS
:
2152 case TRB_BANDWIDTH_EVENT
:
2156 case TRB_MFINDEX_WRAP
:
2158 "TRB %08x%08x status '%s' len %d slot %d ep %d type '%s' flags %c:%c",
2160 xhci_trb_comp_code_string(GET_COMP_CODE(field2
)),
2161 EVENT_TRB_LEN(field2
), TRB_TO_SLOT_ID(field3
),
2162 /* Macro decrements 1, maybe it shouldn't?!? */
2163 TRB_TO_EP_INDEX(field3
) + 1,
2164 xhci_trb_type_string(type
),
2165 field3
& EVENT_DATA
? 'E' : 'e',
2166 field3
& TRB_CYCLE
? 'C' : 'c');
2170 sprintf(str
, "bRequestType %02x bRequest %02x wValue %02x%02x wIndex %02x%02x wLength %d length %d TD size %d intr %d type '%s' flags %c:%c:%c",
2172 (field0
& 0xff00) >> 8,
2173 (field0
& 0xff000000) >> 24,
2174 (field0
& 0xff0000) >> 16,
2175 (field1
& 0xff00) >> 8,
2177 (field1
& 0xff000000) >> 16 |
2178 (field1
& 0xff0000) >> 16,
2179 TRB_LEN(field2
), GET_TD_SIZE(field2
),
2180 GET_INTR_TARGET(field2
),
2181 xhci_trb_type_string(type
),
2182 field3
& TRB_IDT
? 'I' : 'i',
2183 field3
& TRB_IOC
? 'I' : 'i',
2184 field3
& TRB_CYCLE
? 'C' : 'c');
2187 sprintf(str
, "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c:%c:%c:%c",
2188 field1
, field0
, TRB_LEN(field2
), GET_TD_SIZE(field2
),
2189 GET_INTR_TARGET(field2
),
2190 xhci_trb_type_string(type
),
2191 field3
& TRB_IDT
? 'I' : 'i',
2192 field3
& TRB_IOC
? 'I' : 'i',
2193 field3
& TRB_CHAIN
? 'C' : 'c',
2194 field3
& TRB_NO_SNOOP
? 'S' : 's',
2195 field3
& TRB_ISP
? 'I' : 'i',
2196 field3
& TRB_ENT
? 'E' : 'e',
2197 field3
& TRB_CYCLE
? 'C' : 'c');
2200 sprintf(str
, "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c",
2201 field1
, field0
, TRB_LEN(field2
), GET_TD_SIZE(field2
),
2202 GET_INTR_TARGET(field2
),
2203 xhci_trb_type_string(type
),
2204 field3
& TRB_IOC
? 'I' : 'i',
2205 field3
& TRB_CHAIN
? 'C' : 'c',
2206 field3
& TRB_ENT
? 'E' : 'e',
2207 field3
& TRB_CYCLE
? 'C' : 'c');
2211 case TRB_EVENT_DATA
:
2214 "Buffer %08x%08x length %d TD size %d intr %d type '%s' flags %c:%c:%c:%c:%c:%c:%c:%c",
2215 field1
, field0
, TRB_LEN(field2
), GET_TD_SIZE(field2
),
2216 GET_INTR_TARGET(field2
),
2217 xhci_trb_type_string(type
),
2218 field3
& TRB_BEI
? 'B' : 'b',
2219 field3
& TRB_IDT
? 'I' : 'i',
2220 field3
& TRB_IOC
? 'I' : 'i',
2221 field3
& TRB_CHAIN
? 'C' : 'c',
2222 field3
& TRB_NO_SNOOP
? 'S' : 's',
2223 field3
& TRB_ISP
? 'I' : 'i',
2224 field3
& TRB_ENT
? 'E' : 'e',
2225 field3
& TRB_CYCLE
? 'C' : 'c');
2229 case TRB_ENABLE_SLOT
:
2232 xhci_trb_type_string(type
),
2233 field3
& TRB_CYCLE
? 'C' : 'c');
2235 case TRB_DISABLE_SLOT
:
2236 case TRB_NEG_BANDWIDTH
:
2238 "%s: slot %d flags %c",
2239 xhci_trb_type_string(type
),
2240 TRB_TO_SLOT_ID(field3
),
2241 field3
& TRB_CYCLE
? 'C' : 'c');
2245 "%s: ctx %08x%08x slot %d flags %c:%c",
2246 xhci_trb_type_string(type
),
2248 TRB_TO_SLOT_ID(field3
),
2249 field3
& TRB_BSR
? 'B' : 'b',
2250 field3
& TRB_CYCLE
? 'C' : 'c');
2254 "%s: ctx %08x%08x slot %d flags %c:%c",
2255 xhci_trb_type_string(type
),
2257 TRB_TO_SLOT_ID(field3
),
2258 field3
& TRB_DC
? 'D' : 'd',
2259 field3
& TRB_CYCLE
? 'C' : 'c');
2261 case TRB_EVAL_CONTEXT
:
2263 "%s: ctx %08x%08x slot %d flags %c",
2264 xhci_trb_type_string(type
),
2266 TRB_TO_SLOT_ID(field3
),
2267 field3
& TRB_CYCLE
? 'C' : 'c');
2271 "%s: ctx %08x%08x slot %d ep %d flags %c",
2272 xhci_trb_type_string(type
),
2274 TRB_TO_SLOT_ID(field3
),
2275 /* Macro decrements 1, maybe it shouldn't?!? */
2276 TRB_TO_EP_INDEX(field3
) + 1,
2277 field3
& TRB_CYCLE
? 'C' : 'c');
2281 "%s: slot %d sp %d ep %d flags %c",
2282 xhci_trb_type_string(type
),
2283 TRB_TO_SLOT_ID(field3
),
2284 TRB_TO_SUSPEND_PORT(field3
),
2285 /* Macro decrements 1, maybe it shouldn't?!? */
2286 TRB_TO_EP_INDEX(field3
) + 1,
2287 field3
& TRB_CYCLE
? 'C' : 'c');
2291 "%s: deq %08x%08x stream %d slot %d ep %d flags %c",
2292 xhci_trb_type_string(type
),
2294 TRB_TO_STREAM_ID(field2
),
2295 TRB_TO_SLOT_ID(field3
),
2296 /* Macro decrements 1, maybe it shouldn't?!? */
2297 TRB_TO_EP_INDEX(field3
) + 1,
2298 field3
& TRB_CYCLE
? 'C' : 'c');
2302 "%s: slot %d flags %c",
2303 xhci_trb_type_string(type
),
2304 TRB_TO_SLOT_ID(field3
),
2305 field3
& TRB_CYCLE
? 'C' : 'c');
2307 case TRB_FORCE_EVENT
:
2309 "%s: event %08x%08x vf intr %d vf id %d flags %c",
2310 xhci_trb_type_string(type
),
2312 TRB_TO_VF_INTR_TARGET(field2
),
2313 TRB_TO_VF_ID(field3
),
2314 field3
& TRB_CYCLE
? 'C' : 'c');
2318 "%s: belt %d flags %c",
2319 xhci_trb_type_string(type
),
2320 TRB_TO_BELT(field3
),
2321 field3
& TRB_CYCLE
? 'C' : 'c');
2325 "%s: ctx %08x%08x slot %d speed %d flags %c",
2326 xhci_trb_type_string(type
),
2328 TRB_TO_SLOT_ID(field3
),
2329 TRB_TO_DEV_SPEED(field3
),
2330 field3
& TRB_CYCLE
? 'C' : 'c');
2332 case TRB_FORCE_HEADER
:
2334 "%s: info %08x%08x%08x pkt type %d roothub port %d flags %c",
2335 xhci_trb_type_string(type
),
2336 field2
, field1
, field0
& 0xffffffe0,
2337 TRB_TO_PACKET_TYPE(field0
),
2338 TRB_TO_ROOTHUB_PORT(field3
),
2339 field3
& TRB_CYCLE
? 'C' : 'c');
2343 "type '%s' -> raw %08x %08x %08x %08x",
2344 xhci_trb_type_string(type
),
2345 field0
, field1
, field2
, field3
);
2351 static inline const char *xhci_decode_slot_context(u32 info
, u32 info2
,
2352 u32 tt_info
, u32 state
)
2354 static char str
[1024];
2360 speed
= info
& DEV_SPEED
;
2361 hub
= info
& DEV_HUB
;
2362 mtt
= info
& DEV_MTT
;
2364 ret
= sprintf(str
, "RS %05x %s%s%s Ctx Entries %d MEL %d us Port# %d/%d",
2365 info
& ROUTE_STRING_MASK
,
2380 case SLOT_SPEED_SSP
:
2381 s
= "super-speed plus";
2384 s
= "UNKNOWN speed";
2386 mtt
? " multi-TT" : "",
2388 (info
& LAST_CTX_MASK
) >> 27,
2390 DEVINFO_TO_ROOT_HUB_PORT(info2
),
2391 DEVINFO_TO_MAX_PORTS(info2
));
2393 ret
+= sprintf(str
+ ret
, " [TT Slot %d Port# %d TTT %d Intr %d] Addr %d State %s",
2394 tt_info
& TT_SLOT
, (tt_info
& TT_PORT
) >> 8,
2395 GET_TT_THINK_TIME(tt_info
), GET_INTR_TARGET(tt_info
),
2396 state
& DEV_ADDR_MASK
,
2397 xhci_slot_state_string(GET_SLOT_STATE(state
)));
2403 static inline const char *xhci_portsc_link_state_string(u32 portsc
)
2405 switch (portsc
& PORT_PLS_MASK
) {
2424 case XDEV_HOT_RESET
:
2426 case XDEV_COMP_MODE
:
2427 return "Compliance mode";
2428 case XDEV_TEST_MODE
:
2438 static inline const char *xhci_decode_portsc(u32 portsc
)
2440 static char str
[256];
2443 ret
= sprintf(str
, "%s %s %s Link:%s ",
2444 portsc
& PORT_POWER
? "Powered" : "Powered-off",
2445 portsc
& PORT_CONNECT
? "Connected" : "Not-connected",
2446 portsc
& PORT_PE
? "Enabled" : "Disabled",
2447 xhci_portsc_link_state_string(portsc
));
2449 if (portsc
& PORT_OC
)
2450 ret
+= sprintf(str
+ ret
, "OverCurrent ");
2451 if (portsc
& PORT_RESET
)
2452 ret
+= sprintf(str
+ ret
, "In-Reset ");
2454 ret
+= sprintf(str
+ ret
, "Change: ");
2455 if (portsc
& PORT_CSC
)
2456 ret
+= sprintf(str
+ ret
, "CSC ");
2457 if (portsc
& PORT_PEC
)
2458 ret
+= sprintf(str
+ ret
, "PEC ");
2459 if (portsc
& PORT_WRC
)
2460 ret
+= sprintf(str
+ ret
, "WRC ");
2461 if (portsc
& PORT_OCC
)
2462 ret
+= sprintf(str
+ ret
, "OCC ");
2463 if (portsc
& PORT_RC
)
2464 ret
+= sprintf(str
+ ret
, "PRC ");
2465 if (portsc
& PORT_PLC
)
2466 ret
+= sprintf(str
+ ret
, "PLC ");
2467 if (portsc
& PORT_CEC
)
2468 ret
+= sprintf(str
+ ret
, "CEC ");
2469 if (portsc
& PORT_CAS
)
2470 ret
+= sprintf(str
+ ret
, "CAS ");
2472 ret
+= sprintf(str
+ ret
, "Wake: ");
2473 if (portsc
& PORT_WKCONN_E
)
2474 ret
+= sprintf(str
+ ret
, "WCE ");
2475 if (portsc
& PORT_WKDISC_E
)
2476 ret
+= sprintf(str
+ ret
, "WDE ");
2477 if (portsc
& PORT_WKOC_E
)
2478 ret
+= sprintf(str
+ ret
, "WOE ");
2483 static inline const char *xhci_ep_state_string(u8 state
)
2486 case EP_STATE_DISABLED
:
2488 case EP_STATE_RUNNING
:
2490 case EP_STATE_HALTED
:
2492 case EP_STATE_STOPPED
:
2494 case EP_STATE_ERROR
:
2501 static inline const char *xhci_ep_type_string(u8 type
)
2523 static inline const char *xhci_decode_ep_context(u32 info
, u32 info2
, u64 deq
,
2526 static char str
[1024];
2543 esit
= EP_MAX_ESIT_PAYLOAD_HI(info
) << 16 |
2544 EP_MAX_ESIT_PAYLOAD_LO(tx_info
);
2546 ep_state
= info
& EP_STATE_MASK
;
2547 max_pstr
= info
& EP_MAXPSTREAMS_MASK
;
2548 interval
= CTX_TO_EP_INTERVAL(info
);
2549 mult
= CTX_TO_EP_MULT(info
) + 1;
2550 lsa
= info
& EP_HAS_LSA
;
2552 cerr
= (info2
& (3 << 1)) >> 1;
2553 ep_type
= CTX_TO_EP_TYPE(info2
);
2554 hid
= info2
& (1 << 7);
2555 burst
= CTX_TO_MAX_BURST(info2
);
2556 maxp
= MAX_PACKET_DECODED(info2
);
2558 avg
= EP_AVG_TRB_LENGTH(tx_info
);
2560 ret
= sprintf(str
, "State %s mult %d max P. Streams %d %s",
2561 xhci_ep_state_string(ep_state
), mult
,
2562 max_pstr
, lsa
? "LSA " : "");
2564 ret
+= sprintf(str
+ ret
, "interval %d us max ESIT payload %d CErr %d ",
2565 (1 << interval
) * 125, esit
, cerr
);
2567 ret
+= sprintf(str
+ ret
, "Type %s %sburst %d maxp %d deq %016llx ",
2568 xhci_ep_type_string(ep_type
), hid
? "HID" : "",
2571 ret
+= sprintf(str
+ ret
, "avg trb len %d", avg
);
2576 #endif /* __LINUX_XHCI_HCD_H */