/** @file\r
This file provides control over block-oriented firmware devices.\r
\r
- Copyright (c) 2006 - 2008, Intel Corporation \r
- All rights reserved. This program and the accompanying materials \r
- are licensed and made available under the terms and conditions of the BSD License \r
- which accompanies this distribution. The full text of the license may be found at \r
- http://opensource.org/licenses/bsd-license.php \r
-\r
- THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, \r
- WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. \r
+Copyright (c) 2006 - 2011, Intel Corporation. All rights reserved.<BR>\r
+This program and the accompanying materials are licensed and made available under \r
+the terms and conditions of the BSD License that accompanies this distribution. \r
+The full text of the license may be found at\r
+http://opensource.org/licenses/bsd-license.php. \r
+ \r
+THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, \r
+WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. \r
\r
@par Revision Reference: PI\r
- Version 1.00.\r
+ Version 1.0 and 1.2.\r
\r
**/\r
\r
#ifndef __FIRMWARE_VOLUME_BLOCK_H__\r
#define __FIRMWARE_VOLUME_BLOCK_H__\r
\r
-\r
+//\r
+// EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL is defined in PI 1.0 spec and its GUID value\r
+// is later updated to be the same as that of EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL\r
+// defined in PI 1.2 spec. \r
+//\r
#define EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL_GUID \\r
- { 0xDE28BC59, 0x6228, 0x41BD, {0xBD, 0xF6, 0xA3, 0xB9, 0xAD,0xB5, 0x8D, 0xA1 } }\r
+ { 0x8f644fa9, 0xe850, 0x4db1, {0x9c, 0xe2, 0xb, 0x44, 0x69, 0x8e, 0x8d, 0xa4 } }\r
\r
+#define EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL_GUID \\r
+ { 0x8f644fa9, 0xe850, 0x4db1, {0x9c, 0xe2, 0xb, 0x44, 0x69, 0x8e, 0x8d, 0xa4 } }\r
\r
typedef struct _EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL;\r
\r
+typedef EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL; \r
+\r
/**\r
The GetAttributes() function retrieves the attributes and\r
- current settings of the block. Status Codes Returned\r
+ current settings of the block.\r
\r
- @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL instance.\r
+ @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance.\r
\r
@param Attributes Pointer to EFI_FVB_ATTRIBUTES_2 in which the\r
attributes and current settings are\r
typedef\r
EFI_STATUS\r
(EFIAPI * EFI_FVB_GET_ATTRIBUTES)(\r
- IN CONST EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL *This,\r
+ IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This,\r
OUT EFI_FVB_ATTRIBUTES_2 *Attributes\r
);\r
\r
The SetAttributes() function sets configurable firmware volume\r
attributes and returns the new settings of the firmware volume.\r
\r
- @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL instance.\r
+ @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance.\r
\r
@param Attributes On input, Attributes is a pointer to\r
EFI_FVB_ATTRIBUTES_2 that contains the\r
typedef\r
EFI_STATUS\r
(EFIAPI * EFI_FVB_SET_ATTRIBUTES)(\r
- IN CONST EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL *This,\r
+ IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This,\r
IN OUT EFI_FVB_ATTRIBUTES_2 *Attributes\r
);\r
\r
a memory-mapped firmware volume. This function should be called\r
only for memory-mapped firmware volumes.\r
\r
- @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL instance.\r
+ @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance.\r
\r
@param Address Pointer to a caller-allocated\r
EFI_PHYSICAL_ADDRESS that, on successful\r
return from GetPhysicalAddress(), contains the\r
base address of the firmware volume.\r
\r
- @retval EFI_SUCCESS The firmware volume base address is returned.\r
+ @retval EFI_SUCCESS The firmware volume base address was returned.\r
\r
- @retval EFI_NOT_SUPPORTED The firmware volume is not memory mapped.\r
+ @retval EFI_UNSUPPORTED The firmware volume is not memory mapped.\r
\r
**/\r
typedef\r
EFI_STATUS\r
(EFIAPI * EFI_FVB_GET_PHYSICAL_ADDRESS)(\r
- IN CONST EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL *This,\r
+ IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This,\r
OUT EFI_PHYSICAL_ADDRESS *Address\r
);\r
\r
retrieve the block map (see EFI_FIRMWARE_VOLUME_HEADER).\r
\r
\r
- @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL instance.\r
+ @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance.\r
\r
@param Lba Indicates the block for which to return the size.\r
\r
BlockSize.\r
\r
\r
- @retval EFI_SUCCESS The firmware volume base address is returned.\r
+ @retval EFI_SUCCESS The firmware volume base address was returned.\r
\r
@retval EFI_INVALID_PARAMETER The requested LBA is out of range.\r
\r
typedef\r
EFI_STATUS\r
(EFIAPI * EFI_FVB_GET_BLOCK_SIZE)(\r
- IN CONST EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL *This,\r
+ IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This,\r
IN EFI_LBA Lba,\r
OUT UINTN *BlockSize,\r
OUT UINTN *NumberOfBlocks\r
\r
\r
/**\r
+ Reads the specified number of bytes into a buffer from the specified block.\r
+\r
The Read() function reads the requested number of bytes from the\r
requested block and stores them in the provided buffer.\r
Implementations should be mindful that the firmware volume\r
indicate the number of bytes actually read. The caller must be\r
aware that a read may be partially completed.\r
\r
- @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL instance.\r
+ @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance.\r
\r
@param Lba The starting logical block index\r
from which to read.\r
@param Buffer Pointer to a caller-allocated buffer that will\r
be used to hold the data that is read.\r
\r
- @retval EFI_SUCCESS The firmware volume was read successfully\r
+ @retval EFI_SUCCESS The firmware volume was read successfully,\r
and contents are in Buffer.\r
\r
@retval EFI_BAD_BUFFER_SIZE Read attempted across an LBA\r
typedef\r
EFI_STATUS\r
(EFIAPI *EFI_FVB_READ)(\r
- IN CONST EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL *This,\r
+ IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This,\r
IN EFI_LBA Lba,\r
IN UINTN Offset,\r
IN OUT UINTN *NumBytes,\r
);\r
\r
/**\r
+ Writes the specified number of bytes from the input buffer to the block.\r
+\r
The Write() function writes the specified number of bytes from\r
the provided buffer to the specified block and offset. If the\r
firmware volume is sticky write, the caller must ensure that\r
function, or else the result will be unpredictable. This\r
unpredictability arises because, for a sticky-write firmware\r
volume, a write may negate a bit in the EFI_FVB_ERASE_POLARITY\r
- state but it cannot flip it back again. In general, before\r
- calling the Write() function, the caller should call the\r
- EraseBlocks() function first to erase the specified block to\r
+ state but cannot flip it back again. Before calling the\r
+ Write() function, it is recommended for the caller to first call \r
+ the EraseBlocks() function to erase the specified block to\r
write. A block erase cycle will transition bits from the\r
(NOT)EFI_FVB_ERASE_POLARITY state back to the\r
EFI_FVB_ERASE_POLARITY state. Implementations should be\r
fully flushed to the hardware before the Write() service\r
returns.\r
\r
- @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL instance.\r
+ @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL instance.\r
\r
@param Lba The starting logical block index to write to.\r
\r
@param Offset Offset into the block at which to begin writing.\r
\r
- @param NumBytes Pointer to a UINTN. At entry, *NumBytes\r
+ @param NumBytes The pointer to a UINTN. At entry, *NumBytes\r
contains the total size of the buffer. At\r
exit, *NumBytes contains the total number of\r
bytes actually written.\r
\r
- @param Buffer Pointer to a caller-allocated buffer that\r
+ @param Buffer The pointer to a caller-allocated buffer that\r
contains the source for the write.\r
\r
@retval EFI_SUCCESS The firmware volume was written successfully.\r
typedef\r
EFI_STATUS\r
(EFIAPI * EFI_FVB_WRITE)(\r
- IN CONST EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL *This,\r
+ IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This,\r
IN EFI_LBA Lba,\r
IN UINTN Offset,\r
IN OUT UINTN *NumBytes,\r
\r
\r
\r
-//\r
-// EFI_LBA_LIST_TERMINATOR\r
-//\r
+///\r
+/// EFI_LBA_LIST_TERMINATOR\r
+///\r
#define EFI_LBA_LIST_TERMINATOR 0xFFFFFFFFFFFFFFFFULL\r
\r
\r
/**\r
+ Erases and initializes a firmware volume block.\r
+\r
The EraseBlocks() function erases one or more blocks as denoted\r
by the variable argument list. The entire parameter list of\r
blocks must be verified before erasing any blocks. If a block is\r
flushed to the hardware before the EraseBlocks() service\r
returns.\r
\r
- @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL\r
+ @param This Indicates the EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL\r
instance.\r
\r
@param ... The variable argument list is a list of tuples.\r
and consists of the following:\r
- An EFI_LBA that indicates the starting LBA\r
- A UINTN that indicates the number of blocks to\r
- erase\r
+ erase.\r
\r
The list is terminated with an\r
EFI_LBA_LIST_TERMINATOR. For example, the\r
(5-7 and 10-11) are to be erased: EraseBlocks\r
(This, 5, 3, 10, 2, EFI_LBA_LIST_TERMINATOR);\r
\r
- @retval EFI_SUCCESS The erase request was successfully\r
+ @retval EFI_SUCCESS The erase request successfully\r
completed.\r
\r
@retval EFI_ACCESS_DENIED The firmware volume is in the\r
typedef\r
EFI_STATUS\r
(EFIAPI * EFI_FVB_ERASE_BLOCKS)(\r
- IN CONST EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL *This,\r
+ IN CONST EFI_FIRMWARE_VOLUME_BLOCK2_PROTOCOL *This,\r
...\r
);\r
\r
-\r
-\r
-/**\r
- @par Protocol Description:\r
- The Firmware Volume Block Protocol is the low-level interface\r
- to a firmware volume. File-level access to a firmware volume\r
- should not be done using the Firmware Volume Block Protocol.\r
- Normal access to a firmware volume must use the Firmware\r
- Volume Protocol. Typically, only the file system driver that\r
- produces the Firmware Volume Protocol will bind to the\r
- Firmware Volume Block Protocol. The Firmware Volume Block\r
- Protocol provides the following:\r
- - Byte-level read/write functionality.\r
- - Block-level erase functionality.\r
- - It further exposes device-hardening features, such as may be\r
- equired to protect the firmware from unwanted overwriting\r
- and/or erasure.\r
- - It is useful to layer a file system driver on top of the\r
- Firmware Volume Block Protocol.\r
-\r
- This file system driver produces the Firmware Volume Protocol,\r
- which provides file-level access to a firmware volume. The\r
- Firmware Volume Protocol abstracts the file system that is\r
- used to format the firmware volume and the hardware\r
- device-hardening features that may be present.\r
-\r
-\r
- @param GetPhysicalAddress Retrieves the memory-mapped\r
- address of the firmware volume.\r
-\r
- @param GetBlockSize Retrieves the size for a specific block.\r
- Also returns the number of consecutive\r
- similarly sized blocks.\r
-\r
- @param Read Reads n bytes into a buffer from the firmware\r
- volume hardware.\r
-\r
- @param Write Writes n bytes from a buffer into the firmware\r
- volume hardware.\r
-\r
- @param EraseBlocks Erases specified block(s) and sets all\r
- values as indicated by the\r
- EFI_FVB_ERASE_POLARITY bit. See the\r
- EraseBlocks() function description. Type\r
- EFI_FVB_ERASE_POLARITY is defined in\r
- EFI_FIRMWARE_VOLUME_HEADER. ParentHandle\r
- Handle of the parent firmware volume.\r
- \r
- @param GetAttributes Retrieves the current volume attributes.\r
- \r
- @param SetAttributes Sets the current volume attributes.\r
-\r
-**/\r
-struct _EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL {\r
+///\r
+/// The Firmware Volume Block Protocol is the low-level interface\r
+/// to a firmware volume. File-level access to a firmware volume\r
+/// should not be done using the Firmware Volume Block Protocol.\r
+/// Normal access to a firmware volume must use the Firmware\r
+/// Volume Protocol. Typically, only the file system driver that\r
+/// produces the Firmware Volume Protocol will bind to the\r
+/// Firmware Volume Block Protocol.\r
+///\r
+struct _EFI_FIRMWARE_VOLUME_BLOCK_PROTOCOL{\r
EFI_FVB_GET_ATTRIBUTES GetAttributes;\r
EFI_FVB_SET_ATTRIBUTES SetAttributes;\r
EFI_FVB_GET_PHYSICAL_ADDRESS GetPhysicalAddress;\r
EFI_FVB_READ Read;\r
EFI_FVB_WRITE Write;\r
EFI_FVB_ERASE_BLOCKS EraseBlocks;\r
+ ///\r
+ /// The handle of the parent firmware volume.\r
+ /// \r
EFI_HANDLE ParentHandle;\r
};\r
\r
\r
extern EFI_GUID gEfiFirmwareVolumeBlockProtocolGuid;\r
-\r
+extern EFI_GUID gEfiFirmwareVolumeBlock2ProtocolGuid;\r
\r
#endif\r