.. BSD LICENSE
- Copyright (c) 2015-2016 Amazon.com, Inc. or its affiliates.
+ Copyright (c) 2015-2018 Amazon.com, Inc. or its affiliates.
All rights reserved.
Redistribution and use in source and binary forms, with or without
* **CONFIG_RTE_LIBRTE_ENA_PMD** (default y): Enables or disables inclusion
of the ENA PMD driver in the DPDK compilation.
-
- * **CONFIG_RTE_LIBRTE_ENA_DEBUG_INIT** (default y): Enables or disables debug
- logging of device initialization within the ENA PMD driver.
-
* **CONFIG_RTE_LIBRTE_ENA_DEBUG_RX** (default n): Enables or disables debug
logging of RX logic within the ENA PMD driver.
Supported features
------------------
+* MTU configuration
* Jumbo frames up to 9K
-* Port Hardware Statistics
* IPv4/TCP/UDP checksum offload
* TSO offload
* Multiple receive and transmit queues
-* RSS
+* RSS hash
+* RSS indirection table configuration
* Low Latency Queue for Tx
-
-Unsupported features
---------------------
-
-The features supported by the device and not yet supported by this PMD include:
-
-* Asynchronous Event Notification Queue (AENQ)
+* Basic and extended statistics
+* LSC event notification
+* Watchdog (requires handling of timers in the application)
+* Device reset upon failure
Prerequisites
-------------
#. Prepare the system as recommended by DPDK suite. This includes environment
- variables, hugepages configuration, tool-chains and configuration
+ variables, hugepages configuration, tool-chains and configuration.
-#. Insert igb_uio kernel module using the command 'modprobe igb_uio'
+#. ENA PMD can operate with ``vfio-pci``(*) or ``igb_uio`` driver.
-#. Bind the intended ENA device to igb_uio module
+ (*) ENAv2 hardware supports Low Latency Queue v2 (LLQv2). This feature
+ reduces the latency of the packets by pushing the header directly through
+ the PCI to the device, before the DMA is even triggered. For proper work
+ kernel PCI driver must support write combining (WC). In mainline version of
+ ``igb_uio`` (in DPDK repo) it must be enabled by loading module with
+ ``wc_activate=1`` flag (example below). However, mainline's vfio-pci
+ driver in kernel doesn't have WC support yet (planed to be added).
+ If vfio-pci used user should be either turn off ENAv2 (to avoid performance
+ impact) or recompile vfio-pci driver with patch provided in
+ `amzn-github <https://github.com/amzn/amzn-drivers/tree/master/userspace/dpdk/enav2-vfio-patch>`_.
+
+#. Insert ``vfio-pci`` or ``igb_uio`` kernel module using the command
+ ``modprobe vfio-pci`` or ``modprobe uio; insmod igb_uio.ko wc_activate=1``
+ respectively.
+
+#. For ``vfio-pci`` users only:
+ Please make sure that ``IOMMU`` is enabled in your system,
+ or use ``vfio`` driver in ``noiommu`` mode::
+
+ echo 1 > /sys/module/vfio/parameters/enable_unsafe_noiommu_mode
+
+#. Bind the intended ENA device to ``vfio-pci`` or ``igb_uio`` module.
At this point the system should be ready to run DPDK applications. Once the
.. code-block:: console
[...]
- EAL: PCI device 0000:02:00.1 on NUMA socket -1
- EAL: probe driver: 1d0f:ec20 rte_ena_pmd
- EAL: PCI memory mapped at 0x7f9b6c400000
- PMD: eth_ena_dev_init(): Initializing 0:2:0.1
+ EAL: PCI device 0000:00:06.0 on NUMA socket -1
+ EAL: Invalid NUMA socket, default to 0
+ EAL: probe driver: 1d0f:ec20 net_ena
+
Interactive-mode selected
+ testpmd: create a new mbuf pool <mbuf_pool_socket_0>: n=171456, size=2176, socket=0
+ testpmd: preferred mempool ops selected: ring_mp_mc
+ Warning! port-topology=paired and odd forward ports number, the last port will pair with itself.
Configuring Port 0 (socket 0)
Port 0: 00:00:00:11:00:01
Checking link statuses...
- Port 0 Link Up - speed 10000 Mbps - full-duplex
+
Done
testpmd>