to change. If the slot number is -1, the drive is unloaded.
-4. Compilation options
-----------------------
-
-There are a few additional options which can be set when compiling the
-driver. Most people should not need to mess with any of these; they
-are listed here simply for completeness. A compilation option can be
-enabled by adding a line of the form `#define <option> 1' to the top
-of ide-cd.c. All these options are disabled by default.
-
-VERBOSE_IDE_CD_ERRORS
- If this is set, ATAPI error codes will be translated into textual
- descriptions. In addition, a dump is made of the command which
- provoked the error. This is off by default to save the memory used
- by the (somewhat long) table of error descriptions.
-
-STANDARD_ATAPI
- If this is set, the code needed to deal with certain drives which do
- not properly implement the ATAPI spec will be disabled. If you know
- your drive implements ATAPI properly, you can turn this on to get a
- slightly smaller kernel.
-
-NO_DOOR_LOCKING
- If this is set, the driver will never attempt to lock the door of
- the drive.
-
-CDROM_NBLOCKS_BUFFER
- This sets the size of the buffer to be used for a CDROMREADAUDIO
- ioctl. The default is 8.
-
-TEST
- This currently enables an additional ioctl which enables a user-mode
- program to execute an arbitrary packet command. See the source for
- details. This should be left off unless you know what you're doing.
-
-
-5. Common problems
+4. Common problems
------------------
This section discusses some common problems encountered when trying to
expense of low system performance.
-6. cdchange.c
+5. cdchange.c
-------------
/*
}
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
-static void cmd640_init_dev(ide_drive_t *drive)
+static void __init cmd640_init_dev(ide_drive_t *drive)
{
unsigned int i = drive->hwif->channel * 2 + (drive->dn & 1);
};
struct icside_state {
+ unsigned int channel;
+ unsigned int enabled;
void __iomem *irq_port;
void __iomem *ioc_base;
unsigned int sel;
struct icside_state *state = ec->irq_data;
void __iomem *base = state->irq_port;
- writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
- readb(base + ICS_ARCIN_V6_INTROFFSET_2);
+ state->enabled = 1;
- writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
- readb(base + ICS_ARCIN_V6_INTROFFSET_1);
+ switch (state->channel) {
+ case 0:
+ writeb(0, base + ICS_ARCIN_V6_INTROFFSET_1);
+ readb(base + ICS_ARCIN_V6_INTROFFSET_2);
+ break;
+ case 1:
+ writeb(0, base + ICS_ARCIN_V6_INTROFFSET_2);
+ readb(base + ICS_ARCIN_V6_INTROFFSET_1);
+ break;
+ }
}
/* Prototype: icside_irqdisable_arcin_v6 (struct expansion_card *ec, int irqnr)
{
struct icside_state *state = ec->irq_data;
+ state->enabled = 0;
+
readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
}
.irqpending = icside_irqpending_arcin_v6,
};
+/*
+ * Handle routing of interrupts. This is called before
+ * we write the command to the drive.
+ */
+static void icside_maskproc(ide_drive_t *drive, int mask)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct expansion_card *ec = ECARD_DEV(hwif->dev);
+ struct icside_state *state = ecard_get_drvdata(ec);
+ unsigned long flags;
+
+ local_irq_save(flags);
+
+ state->channel = hwif->channel;
+
+ if (state->enabled && !mask) {
+ switch (hwif->channel) {
+ case 0:
+ writeb(0, state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
+ readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
+ break;
+ case 1:
+ writeb(0, state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
+ readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
+ break;
+ }
+ } else {
+ readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_2);
+ readb(state->irq_port + ICS_ARCIN_V6_INTROFFSET_1);
+ }
+
+ local_irq_restore(flags);
+}
+
+static const struct ide_port_ops icside_v6_no_dma_port_ops = {
+ .maskproc = icside_maskproc,
+};
+
#ifdef CONFIG_BLK_DEV_IDEDMA_ICS
/*
* SG-DMA support.
static const struct ide_port_ops icside_v6_port_ops = {
.set_dma_mode = icside_set_dma_mode,
+ .maskproc = icside_maskproc,
};
static void icside_dma_host_set(ide_drive_t *drive, int on)
*/
BUG_ON(dma_channel_active(ec->dma));
+ /*
+ * Ensure that we have the right interrupt routed.
+ */
+ icside_maskproc(drive, 0);
+
/*
* Route the DMA signals to the correct interface.
*/
static const struct ide_port_info icside_v6_port_info __initdata = {
.init_dma = icside_dma_off_init,
+ .port_ops = &icside_v6_no_dma_port_ops,
.dma_ops = &icside_v6_dma_ops,
.host_flags = IDE_HFLAG_SERIALIZE | IDE_HFLAG_MMIO,
.mwdma_mask = ATA_MWDMA2,
static void ide_detach(struct pcmcia_device *link)
{
ide_info_t *info = link->priv;
- ide_hwif_t *hwif = info->host->ports[0];
- unsigned long data_addr, ctl_addr;
dev_dbg(&link->dev, "ide_detach(0x%p)\n", link);
- data_addr = hwif->io_ports.data_addr;
- ctl_addr = hwif->io_ports.ctl_addr;
-
ide_release(link);
- release_region(ctl_addr, 1);
- release_region(data_addr, 8);
-
kfree(info);
} /* ide_detach */
dev_dbg(&link->dev, "ide_release(0x%p)\n", link);
- if (info->ndev)
- /* FIXME: if this fails we need to queue the cleanup somehow
- -- need to investigate the required PCMCIA magic */
+ if (info->ndev) {
+ ide_hwif_t *hwif = host->ports[0];
+ unsigned long data_addr, ctl_addr;
+
+ data_addr = hwif->io_ports.data_addr;
+ ctl_addr = hwif->io_ports.ctl_addr;
+
ide_host_remove(host);
+ info->ndev = 0;
- info->ndev = 0;
+ release_region(ctl_addr, 1);
+ release_region(data_addr, 8);
+ }
pcmcia_disable_device(link);
} /* ide_release */
* bit 7: error, bit 6: interrupting,
* bit 5: FIFO full, bit 4: FIFO empty
*/
- return ((sc1d & 0x50) == 0x40) ? 1 : 0;
+ return ((sc1d & 0x50) == 0x50) ? 1 : 0;
} else {
/*
* bit 3: error, bit 2: interrupting,
* bit 1: FIFO full, bit 0: FIFO empty
*/
- return ((sc1d & 0x05) == 0x04) ? 1 : 0;
+ return ((sc1d & 0x05) == 0x05) ? 1 : 0;
}
}
.remove = __devexit_p(scc_remove),
};
-static int scc_ide_init(void)
+static int __init scc_ide_init(void)
{
return ide_pci_register_driver(&scc_pci_driver);
}
-module_init(scc_ide_init);
-/* -- No exit code?
-static void scc_ide_exit(void)
+static void __exit scc_ide_exit(void)
{
- ide_pci_unregister_driver(&scc_pci_driver);
+ pci_unregister_driver(&scc_pci_driver);
}
-module_exit(scc_ide_exit);
- */
+module_init(scc_ide_init);
+module_exit(scc_ide_exit);
MODULE_DESCRIPTION("PCI driver module for Toshiba SCC IDE");
MODULE_LICENSE("GPL");