According to the datasheet of the H27UCG8T2BTR the NAND Technology field
(6th byte of the "Device Identifier Description", bits 0-2) the
following values are possible:
- 0x0 = 48nm
- 0x1 = 41nm
- 0x2 = 32nm
- 0x3 = 26nm
- 0x4 = 20nm
- (all others are reserved)
Fix this by extending the mask for this field to allow detecting value
0x4 (20nm) as valid NAND technology.
Without this the detection of the ECC requirements fails, because the
code assumes that the device is a 48nm device (0x4 & 0x3 = 0x0) and
aborts with "Invalid ECC requirements" because it cannot map the "ECC
Level". Extending the mask makes the ECC requirement detection code
recognize this chip as <= 26nm and sets up the ECC step size and ECC
strength correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Fixes: 78f3482d7480 ("mtd: nand: hynix: Rework NAND ID decoding to extract more information") Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
commit c51d0ac59f24 ("mtd: nand: Move Samsung specific init/detection
logic in nand_samsung.c") introduced a regression for Samsung SLC NAND
chips. Prior to this commit chip->bits_per_cell was initialized by calling
nand_get_bits_per_cell() before using nand_is_slc().
With the offending commit this call is skipped, leaving
chip->bits_per_cell cleared to zero when the manufacturer specific
'.detect' function calls nand_is_slc() which in turn interprets
bits_per_cell != 1 as indication for an MLC chip.
The effect is that e.g. a K9F1G08U0F NAND chip is falsely detected as
MLC NAND with 4KiB page size rather than SLC with 2KiB page size.
Add a call to nand_get_bits_per_cell() before calling the .detect hook
function in nand_manufacturer_detect(), so that the nand_is_slc()
calls in the manufacturer specific code will return correct results.
Fixes: c51d0ac59f24 ("mtd: nand: Move Samsung specific init/detection logic in nand_samsung.c") Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Bernat, Yehezkel [Tue, 15 Aug 2017 05:19:20 +0000 (08:19 +0300)]
thunderbolt: Allow clearing the key
BugLink: http://bugs.launchpad.net/bugs/1717430
If secure authentication of a devices fails, either because the device
already has another key uploaded, or there is some other error sending
challenge to the device, and the user only wants to approve the device
just once (without a new key being uploaded to the device) the current
implementation does not allow this because the key cannot be cleared
once set even if we allow it to be changed.
Make this scenario possible and allow clearing the key by writing
empty string to the key sysfs file.
Bernat, Yehezkel [Tue, 15 Aug 2017 05:19:12 +0000 (08:19 +0300)]
thunderbolt: Make key root-only accessible
BugLink: http://bugs.launchpad.net/bugs/1717430
Non-root user may read the key back after root wrote it there.
This removes read access to everyone but root.
ACPI / scan: Enable GPEs before scanning the namespace
BugLink: http://bugs.launchpad.net/bugs/1717431
On some systems the platform firmware expects GPEs to be enabled
before the enumeration of devices and if that expectation is not
met, the systems in question may not boot in some situations.
For this reason, change the initialization ordering of the ACPI
subsystem to make it enable GPEs before scanning the namespace
for the first time in order to enumerate devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com> Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Lv Zheng <lv.zheng@intel.com> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit eb7f43c4adb4a789f99f53916182c3401b4e33c7) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
ACPICA: Make it possible to enable runtime GPEs earlier
BugLink: http://bugs.launchpad.net/bugs/1717431
Runtime GPEs have corresponding _Lxx/_Exx methods and are enabled
automatically during the initialization of the ACPI subsystem through
acpi_update_all_gpes() with the assumption that acpi_setup_gpe_for_wake()
will be called in advance for all of the GPEs pointed to by _PRW
objects in the namespace that may be affected by acpi_update_all_gpes().
That is, acpi_ev_initialize_gpe_block() can only be called for a GPE
block after acpi_setup_gpe_for_wake() has been called for all of the
_PRW (wakeup) GPEs in it.
The platform firmware on some systems, however, expects GPEs to be
enabled before the enumeration of devices which is when
acpi_setup_gpe_for_wake() is called and that goes against the above
assumption.
For this reason, introduce a new flag to be set by
acpi_ev_initialize_gpe_block() when automatically enabling a GPE
to indicate to acpi_setup_gpe_for_wake() that it needs to drop the
reference to the GPE coming from acpi_ev_initialize_gpe_block()
and modify acpi_setup_gpe_for_wake() accordingly. These changes
allow acpi_setup_gpe_for_wake() and acpi_ev_initialize_gpe_block()
to be invoked in any order.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit 1312b7e0caca44e7ff312bc2eaa888943384e3e1) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1717431
In some cases GPEs are already active when they are enabled by
acpi_ev_initialize_gpe_block() and whatever happens next may depend
on the result of handling the events signaled by them, so the
events should not be discarded (which is what happens currently) and
they should be handled as soon as reasonably possible.
For this reason, modify acpi_ev_initialize_gpe_block() to
dispatch GPEs with the status flag set in-band right after
enabling them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
(cherry picked from commit ecc1165b8b743fd1503b9c799ae3a9933b89877b) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1708399
The order in __tlb_flush_mm_lazy is to flush TLB first and then clear
the mm->context.flush_mm bit. This can lead to missed flushes as the
bit can be set anytime, the order needs to be the other way aronud.
But this leads to a different race, __tlb_flush_mm_lazy may be called
on two CPUs concurrently. If mm->context.flush_mm is cleared first then
another CPU can bypass __tlb_flush_mm_lazy although the first CPU has
not done the flush yet. In a virtualized environment the time until the
flush is finally completed can be arbitrarily long.
Add a spinlock to serialize __tlb_flush_mm_lazy and use the function
in finish_arch_post_lock_switch as well.
Cc: <stable@vger.kernel.org> Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
(cherry picked from commit 60f07c8ec5fae06c23e9fd7bab67dabce92b3414) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
s390/mm: fix local TLB flushing vs. detach of an mm address space
BugLink: http://bugs.launchpad.net/bugs/1708399
The local TLB flushing code keeps an additional mask in the mm.context,
the cpu_attach_mask. At the time a global flush of an address space is
done the cpu_attach_mask is copied to the mm_cpumask in order to avoid
future global flushes in case the mm is used by a single CPU only after
the flush.
Trouble is that the reset of the mm_cpumask is racy against the detach
of an mm address space by switch_mm. The current order is first the
global TLB flush and then the copy of the cpu_attach_mask to the
mm_cpumask. The order needs to be the other way around.
Cc: <stable@vger.kernel.org> Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
(cherry picked from commit b3e5dc45fd1ec2aa1de6b80008f9295eb17e0659) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
UBUNTU: [Packaging] Add aufs-dkms to the Provides: for kernel packages
BugLink: http://bugs.launchpad.net/bugs/1716093
The aufs-dkms package does not exist in Ubuntu because aufs is
included in the main kernel package. Add it to the Provides: for
the linux-image packages for packages which depnd on it.
Commit f70e4df2b384 ("rtlwifi: Add code to read new versions of
firmware") added code to load an old firmware file if the new one is
not available. Unfortunately that code is never reached because
request_firmware_nowait() does not wait for the firmware to show up
and returns 0 even if the file is not there.
Use the existing fallback mechanism introduced by commit 62009b7f1279
("rtlwifi: rtl8192cu: Add new firmware") instead.
Fixes: f70e4df2b384 ("rtlwifi: Add code to read new versions of firmware") Signed-off-by: Sven Joachim <svenjoac@gmx.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This patch will fix memory leak when firmware request fails
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Sven Joachim <svenjoac@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
As of_device_get_modalias() returns the number of bytes that would have
been written to the target string, regardless of how much did fit in the
buffer, it's possible that the returned index points beyond the buffer
passed to of_device_modalias() - causing memory beyond the buffer to be
null terminated.
Fixes: 0634c2958927 ("of: Add function for generating a DT modalias with a newline") Cc: Rob Herring <robh@kernel.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit 1bc0eb044615 ("scsi: sg: protect accesses to 'reserved' page
array") adds needed concurrency protection for the "reserve" buffer.
Some checks that are initially made outside the lock are replicated once
the lock is taken to ensure the checks and resulting decisions are made
using consistent state.
The check that a request with flag SG_FLAG_MMAP_IO set fits in the
reserve buffer also needs to be performed again under the lock to ensure
the reserve buffer length compared against matches the value in effect
when the request is linked to the reserve buffer. An -ENOMEM should be
returned in this case, instead of switching over to an indirect buffer
as for non-MMAP_IO requests.
Signed-off-by: Todd Poynor <toddpoynor@google.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Take f_mutex around mmap() processing to protect against races with the
SG_SET_RESERVED_SIZE ioctl. Ensure the reserve buffer length remains
consistent during the mapping operation, and set the "mmap called" flag
to prevent further changes to the reserved buffer size as an atomic
operation with the mapping.
[mkp: fixed whitespace]
Signed-off-by: Todd Poynor <toddpoynor@google.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Several legacy devices such as Geode-based Cisco ASA appliances
and DB800 development board do possess CS5536 IDE controller
with different PCI id than existing one. Using pata_generic is
not always feasible as at least DB800 requires MSR quirk from
pata_cs5536 to be used with vendor firmware.
Commit 0a94efb5acbb ("workqueue: implicit ordered attribute should be
overridable") introduced a __WQ_ORDERED_EXPLICIT flag but gave it the
same value as __WQ_LEGACY. I don't believe these were intended to
mean the same thing, so renumber __WQ_ORDERED_EXPLICIT.
Fixes: 0a94efb5acbb ("workqueue: implicit ordered attribute should be ...") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Make it more clear that post commit return ret is really return 0,
and add a missing drm_atomic_helper_cleanup_planes when
drm_atomic_helper_wait_for_fences fails.
Fixes: 839ca903f12e ("drm/nouveau/kms/nv50: transition to atomic interfaces internally") Cc: Ben Skeggs <bskeggs@redhat.com> Cc: dri-devel@lists.freedesktop.org Cc: nouveau@lists.freedesktop.org Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-2-maarten.lankhorst@linux.intel.com Reviewed-by: Sean Paul <seanpaul@chromium.org>
[mlankhorst: Use if (ret) to remove the goto in success case.] Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
It appears that MSI does not work on either G5 PPC nor on a E5500-based
platform, where other hardware is reported to work fine with MSI.
Both tests were conducted with NV4x hardware, so perhaps other (or even
this) hardware can be made to work. It's still possible to force-enable
with config=NvMSI=1 on load.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Right now there is a potential hang situation for postcopy migrations,
if the guest is enabling storage keys on the target system during the
postcopy process.
For storage key virtualization, we have to forbid the empty zero page as
the storage key is a property of the physical page frame. As we enable
storage key handling lazily we then drop all mappings for empty zero
pages for lazy refaulting later on.
This does not work with the postcopy migration, which relies on the
empty zero page never triggering a fault again in the future. The reason
is that postcopy migration will simply read a page on the target system
if that page is a known zero page to fault in an empty zero page. At
the same time postcopy remembers that this page was already transferred
- so any future userfault on that page will NOT be retransmitted again
to avoid races.
If now the guest enters the storage key mode while in postcopy, we will
break this assumption of postcopy.
The solution is to disable the empty zero page for KVM guests early on
and not during storage key enablement. With this change, the postcopy
migration process is guaranteed to start after no zero pages are left.
As guest pages are very likely not empty zero pages anyway the memory
overhead is also pretty small.
While at it this also adds proper page table locking to the zero page
removal.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This patch adds the resources and DMI ID's for the MEN SC31,
which uses a different address region to map the LPC bus than
the one used for the existing SC24.
Signed-off-by: Michael Moese <michael.moese@men.de>
[jth add stable tag] Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
mwifiex records information about various channels as it receives scan
information. It does this by appending to a buffer that was sized
to the max number of supported channels on any band, but there are
numerous problems:
(a) scans can return info from more than one band (e.g., both 2.4 and 5
GHz), so the determined "max" is not large enough
(b) some firmware appears to return multiple results for a given
channel, so the max *really* isn't large enough
(c) there is no bounds checking when stashing these stats, so problems
(a) and (b) can easily lead to buffer overflows
Let's patch this by setting a slightly-more-correct max (that accounts
for a combination of both 2.4G and 5G bands) and adding a bounds check
when writing to our statistics buffer.
Due to problem (b), we still might not properly report all known survey
information (e.g., with "iw <dev> survey dump"), since duplicate results
(or otherwise "larger than expected" results) will cause some
truncation. But that's a problem for a future bugfix.
(And because of this known deficiency, only log the excess at the WARN
level, since that isn't visible by default in this driver and would
otherwise be a bit too noisy.)
Fixes: bf35443314ac ("mwifiex: channel statistics support for mwifiex") Cc: Avinash Patil <patila@marvell.com> Cc: Xinming Hu <huxm@marvell.com> Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Can be reproduced when running dlm_controld (tested on 4.4.x, 4.12.4):
# seq 1 100 | xargs -P0 -n1 dlm_tool join
# seq 1 100 | xargs -P0 -n1 dlm_tool leave
misc_register fails due to duplicate sysfs entry, which causes
dlm_device_register to free ls->ls_device.name.
In dlm_device_deregister the name was freed again, causing memory
corruption.
According to the comment in dlm_device_deregister the name should've been
set to NULL when registration fails,
so this patch does that.
When the caller maps their dmabuf and we return an sg_table, the caller
doesn't expect the pages beneath that sg_table to vanish on a whim (i.e.
under mempressure). The contract is that the pages are pinned for the
duration of the mapping (from dma_buf_map_attachment() to
dma_buf_unmap_attachment). To comply, we need to introduce our own
vgem_object.pages_pin_count and elevate it across the mapping. However,
the drm_prime interface we use calls drv->prime_pin on dma_buf_attach
and drv->prime_unpin on dma_buf_detach, which while that does cover the
mapping is much broader than is desired -- but it will do for now.
v2: also hold the pin across prime_vmap/vunmap
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Testcase: igt/gem_concurrent_blit/*swap*vgem* Fixes: 5ba6c9ff961a ("drm/vgem: Fix mmaping") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tomi Sarvela <tomi.p.sarvela@intel.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: <stable@vger.kernel.org> # needs a backport Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20170622134617.17912-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The global spinlock `l3_remap_lock` is reinitialized every time the
"probe" function `alt_fpga_bridge_probe()` is called. It should only be
initialized once. Use `DEFINE_SPINLOCK()` to initialize it statically.
Fixes: e5f8efa5c8bf ("ARM: socfpga: fpga bridge driver support") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reviewed-By: Moritz Fischer <mdf@kernel.org> Signed-off-by: Alan Tull <atull@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
There is a mistake here where we accidentally use sizeof(TB_CFG_PKG_RESET)
instead of just TB_CFG_PKG_RESET. The size of an int is 4 so it's the
same as TB_CFG_PKG_NOTIFY_ACK.
Fixes: d7f781bfdbf4 ("thunderbolt: Rework control channel to be more reliable") Reported-by: Colin King <colin.king@canonical.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
caam/qi driver does not compile when DEBUG is enabled
(CRYPTO_DEV_FSL_CAAM_DEBUG=y):
drivers/crypto/caam/caamalg_qi.c: In function 'ablkcipher_done':
drivers/crypto/caam/caamalg_qi.c:794:2: error: implicit declaration of function 'dbg_dump_sg' [-Werror=implicit-function-declaration]
dbg_dump_sg(KERN_ERR, "dst @" __stringify(__LINE__)": ",
Since dbg_dump_sg() is shared between caam/jr and caam/qi, move it
in a shared location and export it.
At the same time:
-reduce ifdeferry by providing a no-op implementation for !DEBUG case
-rename it to caam_dump_sg() to be consistent in terms of
exported symbols namespace (caam_*)
On binder_init() the devices string is duplicated and smashed into individual
device names which are passed along. However, the original duplicated string
wasn't freed in case binder_init() failed. Let's free it on error.
The WACOM_HID_WD_TOUCHRINGSTATUS usage is a single bit which tells us
whether the touchring is currently in use or not. Because we need to
reset the axis value to 0 when the finger is removed, we call
'wacom_map_usage' to ensure that the required type/code values are
associated with the usage. The 'wacom_map_usage' also sets up the axis
range and resolution, however, which is not desired in this particular
case.
Although xf86-input-wacom doesn't do really do anything with the ring's
range or resolution, the libinput driver (for Wayland environments)
uses these values to provide proper angle indications to userspace.
Fixes: 60a2218698 ("HID: wacom: generic: add support for touchring") Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
inserts a wait time before reading the conversion register if the
configuration is changed from a previous request.
Currently, the wait time is only the period required for a single
conversion that is calculated as the reciprocal of the sampling frequency.
However we also need to wait for the the previous conversion to complete.
Otherwise we probably get the conversion result for the previous
configuration when the sampling frequency is lower.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on
success, 1 if the device's runtime PM status was already requested status
or error code on failure. So a positive return value doesn't indicate an
error condition.
However, any non-zero return values from buffer preenable and postdisable
callbacks are recognized as an error and this driver reuses the return
value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in
these callbacks. This change fixes the false error detections.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
doesn't insert a wait time before reading the conversion register if the
configuration is not changed from a previous request.
This assumption is broken if the device is runtime suspended and entered
a power-down state. The forthcoming request causes reading a stale result
from the conversion register as the device is runtime resumed just before.
Fix it by adding a flag to detect that condition and insert a necessary
wait time.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode. This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.
If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion. So the conversion register
doesn't contain valid ADC result. Fix it by changing the continuous mode
in probe function.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The crypto API requires saving the last blocks of ciphertext
in req->info for use as IV for CTS mode. The ccree driver
was not doing this. This patch fixes that.
The bug was manifested with cts(cbc(aes)) mode in tcrypt tests.
The mask of sns_key_info1 suggests the upper nybble is being extracted
however the following shift of 8 bits is too large and always results in
0. Fix this by shifting only by 4 bits to correctly get the upper nybble.
Detected by CoverityScan, CID#142891 ("Operands don't affect result")
Fixes: fa590c222fba ("staging: rts5208: add support for rts5208 and rts5288") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:
Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).
I analyzed and instrumented the code and reproduced. My current
belief is that this is happening:
1. async_completed() is called (from IRQ). Moves "as" onto the
completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
async_getcompleted(). Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
lock; removes "as" from completed list and frees it.
5. usbdev_release() is called. Frees "ps".
6. async_completed() finally continues running wake_up(). ...but
wake_up() has a pointer to the freed "ps".
The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):
<...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200
To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
binder_fd_array_object starts with a 4-byte header,
followed by a few fields that are 8 bytes when
ANDROID_BINDER_IPC_32BIT=N.
This can cause alignment issues in a 64-bit kernel
with a 32-bit userspace, as on x86_32 an 8-byte primitive
may be aligned to a 4-byte address. Pad with a __u32
to fix this.
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e1806 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5ded
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f95463d ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5ded ("usb: musb: unconditionally save and restore the context on suspend") Fixes: a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume") Fixes: 1c4d0b4e1806 ("usb: musb: Remove pm_runtime_set_irq_safe") Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Daniel Mack <zonque@gmail.com> Cc: Dave Gerlach <d-gerlach@ti.com> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
The following commit cause a regression on ATI chipsets.
'commit e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk> Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com> Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
Apparently model C920-C has the same issue so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Corsair Strafe RGB keyboard has trouble to initialize:
[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110
Although it may work after several times unpluging/pluging:
[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941
Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.
PCI: Disable VF decoding before pcibios_sriov_disable() updates resources
BugLink: http://bugs.launchpad.net/bugs/1715073
A struct resource represents the address space consumed by a device. We
should not modify that resource while the device is actively using the
address space. For VFs, pci_iov_update_resource() enforces this by
printing a warning and doing nothing if the VFE (VF Enable) and MSE (VF
Memory Space Enable) bits are set.
Previously, both sriov_enable() and sriov_disable() called the
pcibios_sriov_disable() arch hook, which may update the struct resource,
while VFE and MSE were enabled. This effectively dropped the resource
update pcibios_sriov_disable() intended to do.
Disable VF memory decoding before calling pcibios_sriov_disable().
Reported-by: Carol L Soto <clsoto@us.ibm.com> Tested-by: Carol L Soto <clsoto@us.ibm.com> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[bhelgaas: changelog] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: shan.gavin@gmail.com Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org>
(cherry picked from linux-next commit 0fc690a7c3f7053613dcbab6a7613bb6586d8ee2) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
UBUNTU: SAUCE: selftests/seccomp: Support glibc 2.26 siginfo_t.h
The 2.26 release of glibc changed how siginfo_t is defined, and the earlier
work-around to using the kernel definition are no longer needed. The old
way needs to stay around for a while, though.
Jacob Keller [Fri, 1 Sep 2017 20:43:08 +0000 (13:43 -0700)]
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
BugLink: http://bugs.launchpad.net/bugs/1715578
When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.
Fixes: 7073f46e443e ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(cherry picked from commit 3c8f3e96af3a6799841761923d000566645f0942) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
i40e: avoid NVM acquire deadlock during NVM update
BugLink: http://bugs.launchpad.net/bugs/1715578
X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.
Although this should have only affected X722 devices, commit 96a39aed25e6 ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.
This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.
Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.
Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.
Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.
This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de> Fixes: 96a39aed25e6 ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02) Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(cherry picked from commit 09f79fd49d94cda5837e9bfd0cb222232b3b6d9f) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1714571
Some POWER PMU event names have multiple/alternate event codes. These
alternate event codes were listed in the POWER9 JSON files for
reference.
But the perf tool does not seem to handle duplicates cleanly. 'perf
list' shows such duplicate events only once, but 'perf stat' ends up
counting the first event code twice, multiplexing if necessary and we
end up with double the event counts.
Remove the duplicate event codes from the JSON files for now.
Reported-by: Michael Petlan <mpetlan@redhat.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Anton Blanchard <anton@au1.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Link: http://lkml.kernel.org/r/20170830231506.GB20351@us.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
(cherry picked from commit 2a118e1bd22cad57318520d37e3a184b8846c6a2
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
UBUNTU: [Config] Include vmd in storage-core-modules udeb
BugLink: http://bugs.launchpad.net/bugs/1703339
This is a secondary PCIe host bridge which may have NVMe devices
behind it. The module is needed in the installer to install to
these disks.
Note that while theoretically non-disk devices such as NICs could
be connected in a VMD domain, Intel says they do not support such
usage at this time. If supported in the future vmd should be
moved to the kernel-image udeb.
UBUNTU: SAUCE: powerpc/powernv: Clear LPCR[PECE1] via stop-api only for deep state offline
BugLink: http://bugs.launchpad.net/bugs/1715064
commit 24be85a23d1f ("powerpc/powernv: Clear PECE1 in LPCR via
stop-api only on Hotplug") clears the PECE1 bit of the LPCR via
stop-api during CPU-Hotplug to prevent wakeup due to a decrementer on
an offlined CPU which is in a deep stop state.
In the case where the stop-api support is found to be lacking, the
commit 785a12afdb4a ("powerpc/powernv/idle: Disable LOSE_FULL_CONTEXT
states when stop-api fails") disables deep states that lose hypervisor
context. Thus in this case, the offlined CPU will be put to some
shallow idle state.
However, we currently unconditionally clear the PECE1 in LPCR via
stop-api during CPU-Hotplug even when deep states are disabled due to
stop-api failure.
Fix this by clearing PECE1 of LPCR via stop-api during CPU-Hotplug
*only* when the offlined CPU will be put to a deep state that loses
hypervisor context.
Fixes: commit 24be85a23d1f ("powerpc/powernv: Clear PECE1 in LPCR via
stop-api only on Hotplug")
Reported-by: Pavithra Prakash <pavirampu@linux.vnet.ibm.com> Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
(Applied from mailing list patch https://patchwork.ozlabs.org/patch/808233/) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
powerpc/powernv: Clear PECE1 in LPCR via stop-api only on Hotplug
BugLink: http://bugs.launchpad.net/bugs/1715064
Currently we use the stop-api provided by the firmware to program the
SLW engine to restore the values of hypervisor resources that get lost
on deeper idle states (such as winkle). Since the deep states were
only used for CPU-Hotplug on POWER8 systems, we would program the LPCR
to have the PECE1 bit since Hotplugged CPUs shouldn't be spuriously
woken up by decrementer.
On POWER9, some of the deep platform idle states such as stop4 can be
used in cpuidle as well. In this case, we want the CPU in stop4 to be
woken up by the decrementer when some timer on the CPU expires.
In this patch, we program the stop-api for LPCR with PECE1
bit cleared only when we are offlining the CPU and set it
back once the CPU is online.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit 24be85a23d1fcdc72264a062a2e4ebaaea48feab linux-next) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
powerpc/powernv: Save/Restore additional SPRs for stop4 cpuidle
BugLink: http://bugs.launchpad.net/bugs/1715064
The stop4 idle state on POWER9 is a deep idle state which loses
hypervisor resources, but whose latency is low enough that it can be
exposed via cpuidle.
Until now, the deep idle states which lose hypervisor resources (eg:
winkle) were only exposed via CPU-Hotplug. Hence currently on wakeup
from such states, barring a few SPRs which need to be restored to
their older value, rest of the SPRS are reinitialized to their values
corresponding to that at boot time.
When stop4 is used in the context of cpuidle, we want these additional
SPRs to be restored to their older value, to ensure that the context
on the CPU coming back from idle is same as it was before going idle.
In this patch, we define a SPR save area in PACA (since we have used
up the volatile register space in the stack) and on POWER9, we restore
SPRN_PID, SPRN_LDBAR, SPRN_FSCR, SPRN_HFSCR, SPRN_MMCRA, SPRN_MMCR1,
SPRN_MMCR2 to the values they had before entering stop.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit e1c1cfed54326fd2b17c78f0c85092167fc0783b linux-next) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1714112
This causes a conflict with the sbridge module, the advice from
upstream is to disable the option until a fix is available.
The DAC access permissions for several apparmorfs files are wrong.
.access - needs to be writable by all tasks to perform queries
the others in the set only provide a read fn so should be read only.
With policy namespace virtualization all apparmor needs to control
the permission and visibility checks directly which means DAC
access has to be allowed for all user, group, and other.
BugLink: http://bugs.launchpad.net/bugs/1713103 Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Seth Forshee [Wed, 30 Aug 2017 13:14:06 +0000 (08:14 -0500)]
UBUNTU: SAUCE: selftests/powerpc: Disable some ptrace selftests
The ptrace-tm-vsx, ptrace-tm-spd-vsx, and ptrace-tm-spr tests
FTBFS with the gcc in artful due to inline asm which includes r2
in the clobber list. Disable these tests until a solution is
found.
On Denverton micro-server, the presence of the P2SB bridge PCI device is
enabled or disabled by the item 'RelaxSecConf' in BIOS setup menu. When
'RelaxSecConf' is enabled, the P2SB PCI device is present and the pnd2_edac
EDAC driver also uses it to get BAR. Hiding the P2SB PCI device caused the
pnd2_edac EDAC driver failed to get BAR then reported the above failure.
Therefor, store the presence state of P2SB PCI device before unhiding it
for reading BAR and restore the presence state after reading BAR.
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Reported-by: Yunying Sun <yunying.sun@intel.com> Tested-by: Yunying Sun <yunying.sun@intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
(cherry picked from commit bfd4473b850c8cfaa1cdf56b8ef52fae4e8a6ee5
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux.git) Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
If it's hidden by some device driver (e.g. with the i801 I2C driver,
the commit
9424693035a5 ("i2c: i801: Create iTCO device on newer Intel PCHs")
unconditionally hid the P2SB PCI device wrongly) it will make the
pnd2_edac driver read out an invalid BAR value of 0xffffffff and then
fail on ioremap().
Therefore, store the presence state of P2SB PCI device before unhiding
it for reading BAR and restore the presence state after reading BAR.
Qiuxu Zhuo [Mon, 14 Aug 2017 15:48:13 +0000 (23:48 +0800)]
EDAC, pnd2: Mask off the lower four bits of a BAR
BugLink: http://bugs.launchpad.net/bugs/1709257
Bit[0] of BAR is always zero. Bit[2:1] and bit[3] of BAR contain the
information of 'type' and the 'prefetchable' accordingly. Therefore,
mask the lower four bits to retrieve the actual base address of a BAR.
Tony Luck [Thu, 3 Aug 2017 21:05:36 +0000 (14:05 -0700)]
EDAC, pnd2: Build in a minimal sideband driver for Apollo Lake
BugLink: http://bugs.launchpad.net/bugs/1709257
I've been waing a long time for the generic sideband driver to
appear. Patience has run out, so include the minimum here to
just read registers.
Add a new action, SECCOMP_RET_LOG, that logs a syscall before allowing
the syscall. At the implementation level, this action is identical to
the existing SECCOMP_RET_ALLOW action. However, it can be very useful when
initially developing a seccomp filter for an application. The developer
can set the default action to be SECCOMP_RET_LOG, maybe mark any
obviously needed syscalls with SECCOMP_RET_ALLOW, and then put the
application through its paces. A list of syscalls that triggered the
default action (SECCOMP_RET_LOG) can be easily gleaned from the logs and
that list can be used to build the syscall whitelist. Finally, the
developer can change the default action to the desired value.
This provides a more friendly experience than seeing the application get
killed, then updating the filter and rebuilding the app, seeing the
application get killed due to a different syscall, then updating the
filter and rebuilding the app, etc.
The functionality is similar to what's supported by the various LSMs.
SELinux has permissive mode, AppArmor has complain mode, SMACK has
bring-up mode, etc.
SECCOMP_RET_LOG is given a lower value than SECCOMP_RET_ALLOW as allow
while logging is slightly more restrictive than quietly allowing.
Unfortunately, the tests added for SECCOMP_RET_LOG are not capable of
inspecting the audit log to verify that the syscall was logged.
With this patch, the logic for deciding if an action will be logged is:
if action == RET_ALLOW:
do not log
else if action == RET_KILL && RET_KILL in actions_logged:
log
else if action == RET_LOG && RET_LOG in actions_logged:
log
else if filter-requests-logging && action in actions_logged:
log
else if audit_enabled && process-is-being-audited:
log
else:
do not log