When registering mdiobus children, if we get an -EPROBE_DEFER, we shouldn't
ignore it and continue registering the rest of the mdiobus children. This
would permanently prevent the deferring child mdiobus from working instead
of reattempting it in the future. So, if a child mdiobus needs to be
reattempted in the future, defer the entire mdio-mux initialization.
This fixes the issue where PHYs sitting under the mdio-mux aren't
initialized correctly if the PHY's interrupt controller is not yet ready
when the mdio-mux is being probed. Additional context in the link below.
Fixes: 0ca2997d1452 ("netdev/of/phy: Add MDIO bus multiplexer support.") Link: https://lore.kernel.org/lkml/CAGETcx95kHrv8wA-O+-JtfH7H9biJEGJtijuPVN0V5dUKUAB3A@mail.gmail.com/#t Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If we are seeing memory allocation errors, don't try to continue
registering child mdiobus devices. It's unlikely they'll succeed.
Fixes: 342fa1964439 ("mdio: mux: make child bus walking more permissive and errors more verbose") Signed-off-by: Saravana Kannan <saravanak@google.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
qlcnic_83xx_unlock_flash() is called on all paths after we call
qlcnic_83xx_lock_flash(), except for one error path on failure
of QLCRD32(), which may cause a deadlock. This bug is suggested
by a static analysis tool, please advise.
Fixes: 81d0aeb0a4fff ("qlcnic: flash template based firmware reset recovery") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20210816131405.24024-1-dinghao.liu@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit a02e8964eaf92 ("virtio-net: ethtool configurable LRO")
maps LRO to virtio guest offloading features and allows the
administrator to enable and disable those features via ethtool.
This leads to several issues:
- For a device that doesn't support control guest offloads, the "LRO"
can't be disabled triggering WARN in dev_disable_lro() when turning
off LRO or when enabling forwarding bridging etc.
- For a device that supports control guest offloads, the guest
offloads are disabled in cases of bridging, forwarding etc slowing
down the traffic.
Fix this by using NETIF_F_GRO_HW instead. Though the spec does not
guarantee packets to be re-segmented as the original ones,
we can add that to the spec, possibly with a flag for devices to
differentiate between GRO and LRO.
Further, we never advertised LRO historically before a02e8964eaf92
("virtio-net: ethtool configurable LRO") and so bridged/forwarded
configs effectively always relied on virtio receive offloads behaving
like GRO - thus even if this breaks any configs it is at least not
a regression.
Fixes: a02e8964eaf92 ("virtio-net: ethtool configurable LRO") Acked-by: Michael S. Tsirkin <mst@redhat.com> Reported-by: Ivan <ivan@prestigetransportation.com> Tested-by: Ivan <ivan@prestigetransportation.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The number of queues implemented by many virtio backends is limited,
especially some machines have a large number of CPUs. In this case, it
is often impossible to allocate a separate queue for
XDP_TX/XDP_REDIRECT, then xdp cannot be loaded to work, even xdp does
not use the XDP_TX/XDP_REDIRECT.
This patch allows XDP_TX/XDP_REDIRECT to run by reuse the existing SQ
with __netif_tx_lock() hold when there are not enough queues.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Reviewed-by: Dust Li <dust.li@linux.alibaba.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When a packet is sent over a VRF, the POST_ROUTING hooks are called
twice: Once from the VRF interface, and once from the "actual"
interface the packet will be sent from:
1) First SNAT: l3mdev_l3_out() -> vrf_l3_out() -> .. -> vrf_output_direct()
This causes the POST_ROUTING hooks to run.
2) Second SNAT: 'ip_output()' calls POST_ROUTING hooks again.
Similarly for replies, first ip_rcv() calls PRE_ROUTING hooks, and
second vrf_l3_rcv() calls them again.
As an example, consider the following SNAT rule:
> iptables -t nat -A POSTROUTING -p udp -m udp --dport 53 -j SNAT --to-source 2.2.2.2 -o vrf_1
In this case sending over a VRF will create 2 conntrack entries.
The first is from the VRF interface, which performs the IP SNAT.
The second will run the SNAT, but since the "expected reply" will remain
the same, conntrack randomizes the source port of the packet:
e..g With a socket bound to 1.1.1.1:10000, sending to 3.3.3.3:53, the conntrack
rules are:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=0 bytes=0 mark=0 use=1
udp 17 29 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
i.e. First SNAT IP from 1.1.1.1 --> 2.2.2.2, and second the src port is
SNAT-ed from 10000 --> 61033.
But when a reply is sent (3.3.3.3:53 -> 2.2.2.2:61033) only the later
conntrack entry is matched:
udp 17 29 src=2.2.2.2 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 src=3.3.3.3 dst=2.2.2.2 sport=53 dport=61033 packets=1 bytes=49 mark=0 use=1
udp 17 28 src=1.1.1.1 dst=3.3.3.3 sport=10000 dport=53 packets=1 bytes=68 [UNREPLIED] src=3.3.3.3 dst=2.2.2.2 sport=53 dport=10000 packets=0 bytes=0 mark=0 use=1
And a "port 61033 unreachable" ICMP packet is sent back.
The issue is that when PRE_ROUTING hooks are called from vrf_l3_rcv(),
the skb already has a conntrack flow attached to it, which means
nf_conntrack_in() will not resolve the flow again.
This means only the dest port is "reverse-NATed" (61033 -> 10000) but
the dest IP remains 2.2.2.2, and since the socket is bound to 1.1.1.1 it's
not received.
This can be verified by logging the 4-tuple of the packet in '__udp4_lib_rcv()'.
The fix is then to reset the flow when skb is received on a VRF, to let
conntrack resolve the flow again (which now will hit the earlier flow).
To reproduce: (Without the fix "Got pkt_to_nat_port" will not be printed by
running 'bash ./repro'):
$ cat run_in_A1.py
import logging
logging.getLogger("scapy.runtime").setLevel(logging.ERROR)
from scapy.all import *
import argparse
while True:
try:
# Periodically send in order to keep the conntrack entry alive.
s.send(b'a'*40)
resp = s.recvfrom(1024)
msg_name = resp[0].decode('utf-8').split('\0')[0]
print(f"Got {msg_name}", flush=True)
except Exception as e:
pass
$ cat repro.sh
ip netns del A1 2> /dev/null
ip netns del A2 2> /dev/null
ip netns add A1
ip netns add A2
ip -n A1 link add _v0 type veth peer name _v1 netns A2
ip -n A1 link set _v0 up
ip -n A2 link add e00000 type bond
ip -n A2 link add lo0 type dummy
ip -n A2 link add vrf_1 type vrf table 10001
ip -n A2 link set vrf_1 up
ip -n A2 link set e00000 master vrf_1
ip -n A2 addr add 1.1.1.1/24 dev e00000
ip -n A2 link set e00000 up
ip -n A2 link set _v1 master e00000
ip -n A2 link set _v1 up
ip -n A2 link set lo0 up
ip -n A2 addr add 2.2.2.2/32 dev lo0
ip -n A2 neigh add 1.1.1.10 lladdr 77:77:77:77:77:77 dev e00000
ip -n A2 route add 3.3.3.3/32 via 1.1.1.10 dev e00000 table 10001
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022c7 ("bnxt_en: Need memory barrier when processing the completion ring.") Reported-by: Lance Richardson <lance.richardson@broadcom.com> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Reviewed-by: Lance Richardson <lance.richardson@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb044 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
"access skb fields ok" verifier test fails on s390 with the "verifier
bug. zext_dst is set, but no reg is defined" message. The first insns
of the test prog are ...
... and the 3rd one is dead (this does not look intentional to me, but
this is a separate topic).
sanitize_dead_code() converts dead insns into "ja -1", but keeps
zext_dst. When opt_subreg_zext_lo32_rnd_hi32() tries to parse such
an insn, it sees this discrepancy and bails. This problem can be seen
only with JITs whose bpf_jit_needs_zext() returns true.
Fix by clearning dead insns' zext_dst.
The commits that contributed to this problem are:
1. 5aa5bd14c5f8 ("bpf: add initial suite for selftests"), which
introduced the test with the dead code.
2. 5327ed3d44b7 ("bpf: verifier: mark verified-insn with
sub-register zext flag"), which introduced the zext_dst flag.
3. 83a2881903f3 ("bpf: Account for BPF_FETCH in
insn_has_def32()"), which introduced the sanity check.
4. 9183671af6db ("bpf: Fix leakage under speculation on
mispredicted branches"), which bisect points to.
It's best to fix this on stable branches that contain the second one,
since that's the point where the inconsistency was introduced.
Fixes: 5327ed3d44b7 ("bpf: verifier: mark verified-insn with sub-register zext flag") Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20210812151811.184086-2-iii@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
This fixes the incorrect calculation for integer overflow
when the last address of iova range is 0xffffffff.
Fixes: ec33d031a14b ("vhost: detect 32 bit integer wrap around") Reported-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Xie Yongji <xieyongji@bytedance.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20210728130756.97-2-xieyongji@bytedance.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
GCC complains about empty macros in an 'if' statement, so convert
them to 'do {} while (0)' macros.
Fixes these build warnings:
net/dccp/output.c: In function 'dccp_xmit_packet':
../net/dccp/output.c:283:71: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
283 | dccp_pr_debug("transmit_skb() returned err=%d\n", err);
net/dccp/ackvec.c: In function 'dccp_ackvec_update_old':
../net/dccp/ackvec.c:163:80: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
163 | (unsigned long long)seqno, state);
Fixes: dc841e30eaea ("dccp: Extend CCID packet dequeueing interface") Fixes: 380240864451 ("dccp ccid-2: Update code for the Ack Vector input/registration routine") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: dccp@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The 1.2 GHz variant of the Armada 3720 SOC is unstable with DVFS: when
the SOC boots, the WTMI firmware sets clocks and AVS values that work
correctly with 1.2 GHz CPU frequency, but random crashes occur once
cpufreq driver starts scaling.
We do not know currently what is the reason:
- it may be that the voltage value for L0 for 1.2 GHz variant provided
by the vendor in the OTP is simply incorrect when scaling is used,
- it may be that some delay is needed somewhere,
- it may be something else.
The most sane solution now seems to be to simply forbid the cpufreq
driver on 1.2 GHz variant.
Signed-off-by: Marek Behún <kabel@kernel.org> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If probe_device is failing, iommu_group is not initialized because
iommu_group_add_device is not reached, so freeing it will result
in NULL pointer access.
iommu_bus_init
->bus_iommu_probe
->probe_iommu_group in for each:/* return -22 in fail case */
->iommu_probe_device
->__iommu_probe_device /* return -22 here.*/
-> ops->probe_device /* return -22 here.*/
-> iommu_group_get_for_dev
-> ops->device_group
-> iommu_group_add_device //good case
->remove_iommu_group //in fail case, it will remove group
->iommu_release_device
->iommu_group_remove_device // here we don't have group
In my case ops->probe_device (mtk_iommu_probe_device from
mtk_iommu_v1.c) is due to failing fwspec->ops mismatch.
A different wait queue was used when removing ctrl_wait than when adding
it. This effectively made the remove operation without locking compared
to other operations on the wait queue ctrl_wait was part of. This caused
issues like below where dead000000000100 is LIST_POISON1 and dead000000000200 is LIST_POISON2.
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.
[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
After adding physical volumes to a volume group through vgextend, the
kernel will rescan the partitions. This in turn will cause the device
capacity to be queried.
If the device status is set to offline through sysfs at this time, READ
CAPACITY command will return a result which the host byte is
DID_NO_CONNECT, and the capacity of the device will be set to zero in
read_capacity_error(). After setting device status back to running, the
capacity of the device will remain stuck at zero.
Fix this issue by rescanning device when the device state changes to
SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210727034455.1494960-1-lijinlin3@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: lijinlin <lijinlin3@huawei.com> Signed-off-by: Wu Bo <wubo40@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Avoid printing a 'target allocation failed' error if the driver
target_alloc() callback function returns -ENXIO. This return value
indicates that the corresponding H:C:T:L entry is empty.
Removing this error reduces the scan time if the user issues SCAN_WILD_CARD
scan operation through sysfs parameter on a host with a lot of empty
H:C:T:L entries.
Avoiding the printk on -ENXIO matches the behavior of the other callback
functions during scanning.
Link: https://lore.kernel.org/r/20210726115402.1936-1-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix the race between rdac_bus_attach() and rdac_bus_detach() where h->sdev
is NULL when processing the RDAC attach.
Link: https://lore.kernel.org/r/20210113063103.2698953-1-yebin10@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The list_for_each_entry() iterator, "adapter" in this code, can never be
NULL. If we exit the loop without finding the correct adapter then
"adapter" points invalid memory that is an offset from the list head. This
will eventually lead to memory corruption and presumably a kernel crash.
Link: https://lore.kernel.org/r/20210708074642.23599-1-harshvardhan.jha@oracle.com Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If the router_xlate can not find the controller in the available DMA
devices then it should return with -EPORBE_DEFER in a same way as the
of_dma_request_slave_channel() does.
The issue can be reproduced if the event router is registered before the
DMA controller itself and a driver would request for a channel before the
controller is registered.
In of_dma_request_slave_channel():
1. of_dma_find_controller() would find the dma_router
2. ofdma->of_dma_xlate() would fail and returned NULL
3. -ENODEV is returned as error code
with this patch we would return in this case the correct -EPROBE_DEFER and
the client can try to request the channel later.
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by moving the error_pm label above the pm_runtime_put() in
the error path.
When user calls dmaengine_terminate_sync, the driver will clean up any
remaining descriptors for all the pending or active transfers that had
previously been submitted. However, this might happen whilst the tasklet is
invoking the DMA callback for the last finished transfer, so by the time it
returns and takes over the channel's spinlock, the list of completed
descriptors it was traversing is no longer valid. This leads to a
read-after-free situation.
Fix it by signalling whether a user-triggered termination has happened by
means of a boolean variable.
The USB core has utility routines to retrieve various types of
descriptors. These routines will now provoke a WARN if they are asked
to retrieve 0 bytes (USB "receive" requests must not have zero
length), so avert this by checking the size argument at the start.
CC: Johan Hovold <johan@kernel.org> Reported-and-tested-by: syzbot+7dbcd9ff34dc4ed45240@syzkaller.appspotmail.com Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20210607152307.GD1768031@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
syzbot reported memory leak in zr364xx_probe()[1].
The problem was in invalid error handling order.
All error conditions rigth after v4l2_ctrl_handler_init()
must call v4l2_ctrl_handler_free().
Reported-by: syzbot+efe9aefc31ae1e6f7675@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Syzbot discovered that the probe error handling doesn't clean up the
resources allocated in zr364xx_board_init(). There are several
related bugs in this code so I have re-written the error handling.
1) Introduce a new function zr364xx_board_uninit() which cleans up
the resources in zr364xx_board_init().
2) In zr364xx_board_init() if the call to zr364xx_start_readpipe()
fails then release the "cam->buffer.frame[i].lpvbits" memory
before returning. This way every function either allocates
everything successfully or it cleans up after itself.
3) Re-write the probe function so that each failure path goto frees
the most recent allocation. That way we don't free anything
before it has been allocated and we can also verify that
everything is freed.
4) Originally, in the probe function the "cam->v4l2_dev.release"
pointer was set to "zr364xx_release" near the start but I moved
that assignment to the end, after everything had succeeded. The
release function was never actually called during the probe cleanup
process, but with this change I wanted to make it clear that we
don't want to call zr364xx_release() until everything is
allocated successfully.
Next I re-wrote the zr364xx_release() function. Ideally this would
have been a simple matter of copy and pasting the cleanup code from
probe and adding an additional call to video_unregister_device(). But
there are a couple quirks to note.
1) The probe function does not call videobuf_mmap_free() and I don't
know where the videobuf_mmap is allocated. I left the code as-is to
avoid introducing a bug in code I don't understand.
2) The zr364xx_board_uninit() has a call to zr364xx_stop_readpipe()
which is a change from the original behavior with regards to
unloading the driver. Calling zr364xx_stop_readpipe() on a stopped
pipe is not a problem so this is safe and is potentially a bugfix.
Reported-by: syzbot+b4d54814b339b5c6bbd4@syzkaller.appspotmail.com Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
zr364xx_start_readpipe() can fail but callers do not care about that.
This can result in various negative consequences. The patch adds missed
error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Erasing an AMD linear flash card (AM29F016D) crashes after the first
sector has been erased. Likewise, writing to it crashes after two bytes
have been written. The reason is a missing check for a null pointer -
the cmdset_priv field is not set for this type of card.
Fixes: 4844ef80305d ("mtd: cfi_cmdset_0002: Add support for polling status register") Signed-off-by: Andreas Persson <andreasp56@outlook.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/DB6P189MB05830B3530B8087476C5CFE4C1159@DB6P189MB0583.EURP189.PROD.OUTLOOK.COM Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Do not delete a key cache entry that is still being referenced by
pending frames in TXQs. This avoids reuse of the key cache entry while a
frame might still be transmitted using it.
To avoid having to do any additional operations during the main TX path
operations, track pending key cache entries in a new bitmap and check
whether any pending entries can be deleted before every new key
add/remove operation. Also clear any remaining entries when stopping the
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201214172118.18100-6-jouni@codeaurora.org Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
tkip_keymap can be used internally to avoid the reference to key->cipher
and with this, only the key index value itself is needed. This allows
ath_key_delete() call to be postponed to be handled after the upper
layer STA and key entry have already been removed. This is needed to
make ath9k key cache management safer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201214172118.18100-5-jouni@codeaurora.org Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Now that ath/key.c may not be explicitly clearing keys from the key
cache, clear all key cache entries when disabling hardware to make sure
no keys are left behind beyond this point.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201214172118.18100-3-jouni@codeaurora.org Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
It is possible for there to be pending frames in TXQs with a reference
to the key cache entry that is being deleted. If such a key cache entry
is cleared, those pending frame in TXQ might get transmitted without
proper encryption. It is safer to leave the previously used key into the
key cache in such cases. Instead, only clear the MAC address to prevent
RX processing from using this key cache entry.
This is needed in particularly in AP mode where the TXQs cannot be
flushed on station disconnection. This change alone may not be able to
address all cases where the key cache entry might get reused for other
purposes immediately (the key cache entry should be released for reuse
only once the TXQs do not have any remaining references to them), but
this makes it less likely to get unprotected frames and the more
complete changes may end up being significantly more complex.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201214172118.18100-2-jouni@codeaurora.org Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The XSAVE init code initializes all enabled and supported components with
XRSTOR(S) to init state. Then it XSAVEs the state of the components back
into init_fpstate which is used in several places to fill in the init state
of components.
This works correctly with XSAVE, but not with XSAVEOPT and XSAVES because
those use the init optimization and skip writing state of components which
are in init state. So init_fpstate.xsave still contains all zeroes after
this operation.
There are two ways to solve that:
1) Use XSAVE unconditionally, but that requires to reshuffle the buffer when
XSAVES is enabled because XSAVES uses compacted format.
2) Save the components which are known to have a non-zero init state by other
means.
Looking deeper, #2 is the right thing to do because all components the
kernel supports have all-zeroes init state except the legacy features (FP,
SSE). Those cannot be hard coded because the states are not identical on all
CPUs, but they can be saved with FXSAVE which avoids all conditionals.
Use FXSAVE to save the legacy FP/SSE components in init_fpstate along with
a BUILD_BUG_ON() which reminds developers to validate that a newly added
component has all zeroes init state. As a bonus remove the now unused
copy_xregs_to_kernel_booting() crutch.
The XSAVE and reshuffle method can still be implemented in the unlikely
case that components are added which have a non-zero init state and no
other means to save them. For now, FXSAVE is just simple and good enough.
[ bp: Fix a typo or two in the text. ]
Fixes: 6bad06b76892 ("x86, xsave: Use xsaveopt in context-switch path when supported") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20210618143444.587311343@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
ext4 supports max number of logical blocks in a file to be 0xffffffff.
(This is since ext4_extent's ee_block is __le32).
This means that EXT4_MAX_LOGICAL_BLOCK should be 0xfffffffe (starting
from 0 logical offset). This patch fixes this.
The issue was seen when ext4 moved to iomap_fiemap API and when
overlayfs was mounted on top of ext4. Since overlayfs was missing
filemap_check_ranges(), so it could pass a arbitrary huge length which
lead to overflow of map.m_len logic.
This patch fixes that.
Fixes: d3b6f23f7167 ("ext4: move ext4_fiemap to use iomap framework") Reported-by: syzbot+77fa5bdb65cc39711820@syzkaller.appspotmail.com Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20200505154324.3226743-2-hch@lst.de Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: George Kennedy <george.kennedy@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The IOMMU driver calculates the guest addressability for a DMA request
based on the value of the mgaw reported from the IOMMU. However, this
is a fused value and as mentioned in the spec, the guest width
should be calculated based on the minimum of supported adjusted guest
address width (SAGAW) and MGAW.
This is from specification:
"Guest addressability for a given DMA request is limited to the
minimum of the value reported through this field and the adjusted
guest address width of the corresponding page-table structure.
(Adjusted guest address widths supported by hardware are reported
through the SAGAW field)."
This causes domain initialization to fail and following
errors appear for EHCI PCI driver:
[ 2.486393] ehci-pci 0000:01:00.4: EHCI Host Controller
[ 2.486624] ehci-pci 0000:01:00.4: new USB bus registered, assigned bus
number 1
[ 2.489127] ehci-pci 0000:01:00.4: DMAR: Allocating domain failed
[ 2.489350] ehci-pci 0000:01:00.4: DMAR: 32bit DMA uses non-identity
mapping
[ 2.489359] ehci-pci 0000:01:00.4: can't setup: -12
[ 2.489531] ehci-pci 0000:01:00.4: USB bus 1 deregistered
[ 2.490023] ehci-pci 0000:01:00.4: init 0000:01:00.4 fail, -12
[ 2.490358] ehci-pci: probe of 0000:01:00.4 failed with error -12
This issue happens when the value of the sagaw corresponds to a
48-bit agaw. This fix updates the calculation of the agaw based on
the minimum of IOMMU's sagaw value and MGAW.
This issue happens on the code path of getting a private domain for a
device. A private domain was needed when the domain of an iommu group
couldn't meet the requirement of a device. The IOMMU core has been
evolved to eliminate the need for private domain, hence this code path
has alreay been removed from the upstream since commit 327d5b2fee91c
("iommu/vt-d: Allow 32bit devices to uses DMA domain"). Instead of back
porting all patches that are required for removing the private domain,
this simply fixes it in the affected stable kernel between v4.16 and v5.7.
[baolu: The orignal patch could be found here
https://lore.kernel.org/linux-iommu/20210412202736.70765-1-saeed.mirzamohammadi@oracle.com/.
I added commit message according to Greg's comments at
https://lore.kernel.org/linux-iommu/YHZ%2FT9x7Xjf1r6fI@kroah.com/.]
A recent change in LLVM causes module_{c,d}tor sections to appear when
CONFIG_K{A,C}SAN are enabled, which results in orphan section warnings
because these are not handled anywhere:
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_ctor) is being placed in '.text.asan.module_ctor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_dtor) is being placed in '.text.asan.module_dtor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.tsan.module_ctor) is being placed in '.text.tsan.module_ctor'
Fangrui explains: "the function asan.module_ctor has the SHF_GNU_RETAIN
flag, so it is in a separate section even with -fno-function-sections
(default)".
Place them in the TEXT_TEXT section so that these technologies continue
to work with the newer compiler versions. All of the KASAN and KCSAN
KUnit tests continue to pass after this change.
There is a race in ceph_put_snap_realm. The change to the nref and the
spinlock acquisition are not done atomically, so you could decrement
nref, and before you take the spinlock, the nref is incremented again.
At that point, you end up putting it on the empty list when it
shouldn't be there. Eventually __cleanup_empty_realms runs and frees
it when it's still in-use.
Fix this by protecting the 1->0 transition with atomic_dec_and_lock,
and just drop the spinlock if we can get the rwsem.
Because these objects can also undergo a 0->1 refcount transition, we
must protect that change as well with the spinlock. Increment locklessly
unless the value is at 0, in which case we take the spinlock, increment
and then take it off the empty list if it did the 0->1 transition.
With these changes, I'm removing the dout() messages from these
functions, as well as in __put_snap_realm. They've always been racy, and
it's better to not print values that may be misleading.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/46419 Reported-by: Mark Nelson <mnelson@redhat.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Luis Henriques <lhenriques@suse.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
They both say that the snap_rwsem must be held for write, but I don't
see any real reason for it, and it's not currently always called that
way.
The lookup is just walking the rbtree, so holding it for read should be
fine there. The "get" is bumping the refcount and (possibly) removing
it from the empty list. I see no need to hold the snap_rwsem for write
for that.
Use the secondary_exec_controls_get() accessor in vmx_has_waitpkg() to
effectively get the controls for the current VMCS, as opposed to using
vmx->secondary_exec_controls, which is the cached value of KVM's desired
controls for vmcs01 and truly not reflective of any particular VMCS.
While the waitpkg control is not dynamic, i.e. vmcs01 will always hold
the same waitpkg configuration as vmx->secondary_exec_controls, the same
does not hold true for vmcs02 if the L1 VMM hides the feature from L2.
If L1 hides the feature _and_ does not intercept MSR_IA32_UMWAIT_CONTROL,
L2 could incorrectly read/write L1's virtual MSR instead of taking a #GP.
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acbe8 ("PCI MSI: Refactor interrupt masking code") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The comments about preserving the cached state in pci_msi[x]_shutdown() are
misleading as the MSI descriptors are freed right after those functions
return. So there is nothing to restore. Preparatory change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.621609423@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
msi_mask_irq() takes a mask and a flags argument. The mask argument is used
to mask out bits from the cached mask and the flags argument to set bits.
Some places invoke it with a flags argument which sets bits which are not
used by the device, i.e. when the device supports up to 8 vectors a full
unmask in some places sets the mask to 0xFFFFFF00. While devices probably
do not care, it's still bad practice.
Fixes: 7ba1930db02f ("PCI MSI: Unmask MSI if setup failed") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.568173099@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Nothing enforces the posted writes to be visible when the function
returns. Flush them even if the flush might be redundant when the entry is
masked already as the unmask will flush as well. This is either setup or a
rare affinity change event so the extra flush is not the end of the world.
While this is more a theoretical issue especially the logic in the X86
specific msi_set_affinity() function relies on the assumption that the
update has reached the hardware when the function returns.
Again, as this never has been enforced the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.515188147@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The specification (PCIe r5.0, sec 6.1.4.5) states:
For MSI-X, a function is permitted to cache Address and Data values
from unmasked MSI-X Table entries. However, anytime software unmasks a
currently masked MSI-X Table entry either by clearing its Mask bit or
by clearing the Function Mask bit, the function must update any Address
or Data values that it cached from that entry. If software changes the
Address or Data value of an entry while the entry is unmasked, the
result is undefined.
The Linux kernel's MSI-X support never enforced that the entry is masked
before the entry is modified hence the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Enforce the entry to be masked across the update.
There is no point in enforcing this to be handled at all possible call
sites as this is just pointless code duplication and the common update
function is the obvious place to enforce this.
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support") Reported-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.462096385@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
1) msix_setup_entries() allocates the MSI descriptors and initializes them
except for the msi_desc:masked member which is left zero initialized.
2) pci_msi_setup_msi_irqs() allocates the interrupt descriptors and sets
up the MSI interrupts which ends up in pci_write_msi_msg() unless the
interrupt chip provides its own irq_write_msi_msg() function.
3) msix_program_entries() does not do what the name suggests. It solely
updates the entries array (if not NULL) and initializes the masked
member for each MSI descriptor by reading the hardware state and then
masks the entry.
Obviously this has some issues:
1) The uninitialized masked member of msi_desc prevents the enforcement
of masking the entry in pci_write_msi_msg() depending on the cached
masked bit. Aside of that half initialized data is a NONO in general
2) msix_program_entries() only ensures that the actually allocated entries
are masked. This is wrong as experimentation with crash testing and
crash kernel kexec has shown.
This limited testing unearthed that when the production kernel had more
entries in use and unmasked when it crashed and the crash kernel
allocated a smaller amount of entries, then a full scan of all entries
found unmasked entries which were in use in the production kernel.
This is obviously a device or emulation issue as the device reset
should mask all MSI-X table entries, but obviously that's just part
of the paper specification.
Cure this by:
1) Masking all table entries in hardware
2) Initializing msi_desc::masked in msix_setup_entries()
3) Removing the mask dance in msix_program_entries()
4) Renaming msix_program_entries() to msix_update_entries() to
reflect the purpose of that function.
As the masking of unused entries has never been done the Fixes tag refers
to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.403833459@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The ordering of MSI-X enable in hardware is dysfunctional:
1) MSI-X is disabled in the control register
2) Various setup functions
3) pci_msi_setup_msi_irqs() is invoked which ends up accessing
the MSI-X table entries
4) MSI-X is enabled and masked in the control register with the
comment that enabling is required for some hardware to access
the MSI-X table
Step #4 obviously contradicts #3. The history of this is an issue with the
NIU hardware. When #4 was introduced the table access actually happened in
msix_program_entries() which was invoked after enabling and masking MSI-X.
This was changed in commit d71d6432e105 ("PCI/MSI: Kill redundant call of
irq_set_msi_desc() for MSI-X interrupts") which removed the table write
from msix_program_entries().
Interestingly enough nobody noticed and either NIU still works or it did
not get any testing with a kernel 3.19 or later.
Nevertheless this is inconsistent and there is no reason why MSI-X can't be
enabled and masked in the control register early on, i.e. move step #4
above to step #1. This preserves the NIU workaround and has no side effects
on other hardware.
Fixes: d71d6432e105 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
When the interrupt interval is greater than 2 ^ PREDICTION_BUFFER_SIZE *
PREDICTION_FACTOR us and less than 1s, the calculated index will be greater
than the length of irqs->ema_time[]. Check the calculated index before
using it to prevent array overflow.
Fixes: 23aa3b9a6b7d ("genirq/timings: Encapsulate storing function") Signed-off-by: Ben Dai <ben.dai@unisoc.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210425150903.25456-1-ben.dai9703@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
msi_domain_alloc_irqs() invokes irq_domain_activate_irq(), but
msi_domain_free_irqs() does not enforce deactivation before tearing down
the interrupts.
This happens when PCI/MSI interrupts are set up and never used before being
torn down again, e.g. in error handling pathes. The only place which cleans
that up is the error handling path in msi_domain_alloc_irqs().
Move the cleanup from msi_domain_alloc_irqs() into msi_domain_free_irqs()
to cure that.
Fixes: f3b0946d629c ("genirq/msi: Make sure PCI MSIs are activated early") Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210518033117.78104-1-cuibixuan@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Creating a new sub monitoring group in the root /sys/fs/resctrl leads to
getting the "Unavailable" value for mbm_total_bytes and mbm_local_bytes
on the entire filesystem.
When a new monitoring group is created, a new RMID is assigned to the
new group. But the RMID is not active yet. When the events are read on
the new RMID, it is expected to report the status as "Unavailable".
When the user reads the events on the default monitoring group with
multiple subgroups, the events on all subgroups are consolidated
together. Currently, if any of the RMID reads report as "Unavailable",
then everything will be reported as "Unavailable".
Fix the issue by discarding the "Unavailable" reads and reporting all
the successful RMID reads. This is not a problem on Intel systems as
Intel reports 0 on Inactive RMIDs.
The IO/APIC cannot handle interrupt affinity changes safely after startup
other than from an interrupt handler. The startup sequence in the generic
interrupt code violates that assumption.
Mark the irq chip with the new IRQCHIP_AFFINITY_PRE_STARTUP flag so that
the default interrupt setting happens before the interrupt is started up
for the first time.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.832143400@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The X86 MSI mechanism cannot handle interrupt affinity changes safely after
startup other than from an interrupt handler, unless interrupt remapping is
enabled. The startup sequence in the generic interrupt code violates that
assumption.
Mark the irq chips with the new IRQCHIP_AFFINITY_PRE_STARTUP flag so that
the default interrupt setting happens before the interrupt is started up
for the first time.
While the interrupt remapping MSI chip does not require this, there is no
point in treating it differently as this might spare an interrupt to a CPU
which is not in the default affinity mask.
For the non-remapping case go to the direct write path when the interrupt
is not yet started similar to the not yet activated case.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.886722080@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
X86 IO/APIC and MSI interrupts (when used without interrupts remapping)
require that the affinity setup on startup is done before the interrupt is
enabled for the first time as the non-remapped operation mode cannot safely
migrate enabled interrupts from arbitrary contexts. Provide a new irq chip
flag which allows affected hardware to request this.
This has to be opt-in because there have been reports in the past that some
interrupt chips cannot handle affinity setting before startup.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.779791738@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There is no real mode for booke arch and the MMU translation is
always on. The corresponding MSR_IS/MSR_DS bit in booke is used
to switch the address space, but not for real mode judgment.
Fixes: 21f8b2fa3ca5 ("powerpc/kprobes: Ignore traps that happened in real mode") Signed-off-by: Pu Lehui <pulehui@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210809023658.218915-1-pulehui@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There is a race between iterating over requests in
nbd_clear_que() and completing requests in recv_work(),
which can lead to double completion of a request.
To fix it, flush the recv worker before iterating over
the requests and don't abort the completed request
while iterating.
lock_sock() may do initiative schedule when the 'sk' is owned by
other thread at the same time, we would receivce a warning message
that "scheduling while atomic".
Even worse, if the next task (selected by the scheduler) try to
release a 'sk', it need to request vsock_table_lock and the deadlock
occur, cause the system into softlockup state.
Call trace:
queued_spin_lock_slowpath
vsock_remove_bound
vsock_remove_sock
virtio_transport_release
__vsock_release
vsock_release
__sock_release
sock_close
__fput
____fput
So we should not require sk_lock in this case, just like the behavior
in vhost_vsock or vmci.
There is a TOCTOU issue in set_evtchn_to_irq. Rows in the evtchn_to_irq
mapping are lazily allocated in this function. The check whether the row
is already present and the row initialization is not synchronized. Two
threads can at the same time allocate a new row for evtchn_to_irq and
add the irq mapping to the their newly allocated row. One thread will
overwrite what the other has set for evtchn_to_irq[row] and therefore
the irq mapping is lost. This will trigger a BUG_ON later in
bind_evtchn_to_cpu:
This patch sets evtchn_to_irq rows via a cmpxchg operation so that they
will be set only once. The row is now cleared before writing it to
evtchn_to_irq in order to not create a race once the row is visible for
other threads.
While at it, do not require the page to be zeroed, because it will be
overwritten with -1's in clear_evtchn_to_irq_row anyway.
Signed-off-by: Maximilian Heyne <mheyne@amazon.de> Fixes: d0b075ffeede ("xen/events: Refactor evtchn_to_irq array to be dynamically allocated") Link: https://lore.kernel.org/r/20210812130930.127134-1-mheyne@amazon.de Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Currently if BBR congestion control is initialized after more than 2B
packets have been delivered, depending on the phase of the
tp->delivered counter the tracking of BBR round trips can get stuck.
The bug arises because if tp->delivered is between 2^31 and 2^32 at
the time the BBR congestion control module is initialized, then the
initialization of bbr->next_rtt_delivered to 0 will cause the logic to
believe that the end of the round trip is still billions of packets in
the future. More specifically, the following check will fail
repeatedly:
and thus the connection will take up to 2B packets delivered before
that check will pass and the connection will set:
bbr->round_start = 1;
This could cause many mechanisms in BBR to fail to trigger, for
example bbr_check_full_bw_reached() would likely never exit STARTUP.
This bug is 5 years old and has not been observed, and as a practical
matter this would likely rarely trigger, since it would require
transferring at least 2B packets, or likely more than 3 terabytes of
data, before switching congestion control algorithms to BBR.
This patch is a stable candidate for kernels as far back as v4.9,
when tcp_bbr.c was added.
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Kevin Yang <yyd@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20210811024056.235161-1-ncardwell@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
After migrating my laptop from 4.19-LTS to 5.4-LTS a while ago I noticed
that my Ethernet port to which a bond and a VLAN interface are attached
appeared to remain up after resuming from suspend with the cable unplugged
(and that problem still persists with 5.10-LTS).
It happens that the following happens:
- the network driver (e1000e here) prepares to suspend, calls e1000e_down()
which calls netif_carrier_off() to signal that the link is going down.
- netif_carrier_off() adds a link_watch event to the list of events for
this device
- the device is completely stopped.
- the machine suspends
- the cable is unplugged and the machine brought to another location
- the machine is resumed
- the queued linkwatch events are processed for the device
- the device doesn't yet have the __LINK_STATE_PRESENT bit and its events
are silently dropped
- the device is resumed with its link down
- the upper VLAN and bond interfaces are never notified that the link had
been turned down and remain up
- the only way to provoke a change is to physically connect the machine
to a port and possibly unplug it.
The state after resume looks like this:
$ ip -br li | egrep 'bond|eth'
bond0 UP e8:6a:64:64:64:64 <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP>
eth0 DOWN e8:6a:64:64:64:64 <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP>
eth0.2@eth0 UP e8:6a:64:64:64:64 <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP>
Placing an explicit call to netdev_state_change() either in the suspend
or the resume code in the NIC driver worked around this but the solution
is not satisfying.
The issue in fact really is in link_watch that loses events while it
ought not to. It happens that the test for the device being present was
added by commit 124eee3f6955 ("net: linkwatch: add check for netdevice
being present to linkwatch_do_dev") in 4.20 to avoid an access to
devices that are not present.
Instead of dropping events, this patch proceeds slightly differently by
postponing their handling so that they happen after the device is fully
resumed.
Fixes: 124eee3f6955 ("net: linkwatch: add check for netdevice being present to linkwatch_do_dev") Link: https://lists.openwall.net/netdev/2018/03/15/62 Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Link: https://lore.kernel.org/r/20210809160628.22623-1-w@1wt.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
On error path of br_add_if(), p->mcast_stats allocated in
new_nbp() need be freed, or it will be leaked.
Fixes: 1080ab95e3c7 ("net: bridge: add support for IGMP/MLD stats and export them via netlink") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Link: https://lore.kernel.org/r/20210809132023.978546-1-yangyingliang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 58c59ef9e930 ("net: dsa: lantiq: Add Forwarding Database access") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: ab335349b852 ("net: dsa: lan9303: Add port_fast_age and port_fdb_dump methods") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix the data-race reported by syzbot [1]
Issue here is that igmp_ifc_timer_expire() can update in_dev->mr_ifc_count
while another change just occured from another context.
in_dev->mr_ifc_count is only 8bit wide, so the race had little
consequences.
[1]
BUG: KCSAN: data-race in igmp_ifc_event / igmp_ifc_timer_expire
write to 0xffff8881051e3062 of 1 bytes by task 12547 on cpu 0:
igmp_ifc_event+0x1d5/0x290 net/ipv4/igmp.c:821
igmp_group_added+0x462/0x490 net/ipv4/igmp.c:1356
____ip_mc_inc_group+0x3ff/0x500 net/ipv4/igmp.c:1461
__ip_mc_join_group+0x24d/0x2c0 net/ipv4/igmp.c:2199
ip_mc_join_group_ssm+0x20/0x30 net/ipv4/igmp.c:2218
do_ip_setsockopt net/ipv4/ip_sockglue.c:1285 [inline]
ip_setsockopt+0x1827/0x2a80 net/ipv4/ip_sockglue.c:1423
tcp_setsockopt+0x8c/0xa0 net/ipv4/tcp.c:3657
sock_common_setsockopt+0x5d/0x70 net/core/sock.c:3362
__sys_setsockopt+0x18f/0x200 net/socket.c:2159
__do_sys_setsockopt net/socket.c:2170 [inline]
__se_sys_setsockopt net/socket.c:2167 [inline]
__x64_sys_setsockopt+0x62/0x70 net/socket.c:2167
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 12539 Comm: syz-executor.1 Not tainted 5.14.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
ksz_read64() currently does some dubious byte-swapping on the two
halves of a 64-bit register, and then only returns the high bits.
Replace this with a straightforward expression.
Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Add support for the OSD1 HDR registers so meson DRM can handle the HDR
properties set by Amlogic u-boot on G12A and newer devices which result
in blue/green/pink colour distortion to display output.
This takes the original patch submissions from Mathias [0] and [1] with
corrections for formatting and the missing description and attribution
needed for merge.
When mirror/redirect a skb to a different port, the ct info should be reset
for reclassification. Or the pkts will match unexpected rules. For example,
with following topology and commands:
IFLA_IFNAME is nul-term string which means that IFLA_IFNAME buffer can be
larger than length of string which contains.
Function __rtnl_newlink() generates new own ifname if either IFLA_IFNAME
was not specified at all or userspace passed empty nul-term string.
It is expected that if userspace does not specify ifname for new ppp netdev
then kernel generates one in format "ppp<id>" where id matches to the ppp
unit id which can be later obtained by PPPIOCGUNIT ioctl.
And it works in this way if IFLA_IFNAME is not specified at all. But it
does not work when IFLA_IFNAME is specified with empty string.
So fix this logic also for empty IFLA_IFNAME in ppp_nl_newlink() function
and correctly generates ifname based on ppp unit identifier if userspace
did not provided preferred ifname.
Without this patch when IFLA_IFNAME was specified with empty string then
kernel created a new ppp interface in format "ppp<id>" but id did not
match ppp unit id returned by PPPIOCGUNIT ioctl. In this case id was some
number generated by __rtnl_newlink() function.
Signed-off-by: Pali Rohár <pali@kernel.org> Fixes: bb8082f69138 ("ppp: build ifname using unit identifier for rtnl based devices") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Commit a5e63c7d38d5 "net: phy: micrel: Fix detection of ksz87xx
switch" broke link detection on the external ports of the KSZ8795.
The previously unused phy_driver structure for these devices specifies
config_aneg and read_status functions that appear to be designed for a
fixed link and do not work with the embedded PHYs in the KSZ8795.
Delete the use of these functions in favour of the generic PHY
implementations which were used previously.
Fixes: a5e63c7d38d5 ("net: phy: micrel: Fix detection of ksz87xx switch") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The gpiod_lookup_table.table passed to gpiod_add_lookup_table() must
be terminated with an empty entry, add this.
Note we have likely been getting away with this not being present because
the GPIO lookup code first matches on the dev_id, causing most lookups to
skip checking the table and the lookups which do check the table will
find a matching entry before reaching the end. With that said, terminating
these tables properly still is obviously the correct thing to do.
Fixes: f8eb0235f659 ("x86: pcengines apuv2 gpio/leds/keys platform driver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210806115515.12184-1-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Explanation why this does not work:
This change connects the simswap to the LED subsystem of the kernel.
From my point of view, it's nonsense. If we do it this way, then this
can be switched relatively easily via the LED subsystem (trigger:
none/default-on) and that is dangerous! If this is used, it would be
unfavorable, since there is also another trigger (trigger:
heartbeat/netdev).
Therefore, this simswap GPIO should remain in the GPIO
subsystem and be switched via it and not be connected to the LED
subsystem. To avoid the problems mentioned above. The LED subsystem is
not made for this and it is not a good compromise, but rather dangerous.
Signed-off-by: Florian Eckert <fe@dev.tdt.de> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: DENG Qingfang <dqfext@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
An I2S frame starts on the falling edge of LRCLK so ASP_STP must
be 0.
At the same time, move other format settings in the same register
from cs42l42_pll_config() to cs42l42_set_dai_fmt() where you'd
expect to find them, and merge into a single write.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Link: https://lore.kernel.org/r/20210805161111.10410-2-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The driver was defining two ALSA controls that both change the same
register field for the wind noise filter corner frequency. The filter
response has two corners, at different frequencies, and the duplicate
controls most likely were an attempt to be able to set the value using
either of the frequencies.
However, having two controls changing the same field can be problematic
and it is unnecessary. Both frequencies are related to each other so
setting one implies exactly what the other would be.
Removing a control affects user-side code, but there is currently no
known use of the removed control so it would be best to remove it now
before it becomes a problem.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Link: https://lore.kernel.org/r/20210803160834.9005-2-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The underlying register field has inverted sense (0 = enabled) so
the control definition must be marked as inverted.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Link: https://lore.kernel.org/r/20210803160834.9005-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The driver has no support for left-justified protocol so it should
not have been allowing this to be passed to cs42l42_set_dai_fmt().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Link: https://lore.kernel.org/r/20210729170929.6589-2-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
The ADC volume is a signed 8-bit number with range -97 to +12,
with -97 being mute. Use a SOC_SINGLE_S8_TLV() to define this
and fix the DECLARE_TLV_DB_SCALE() to have the correct start and
mute flag.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20210729170929.6589-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Both MAC802154_HWSIM_ATTR_RADIO_ID and MAC802154_HWSIM_ATTR_RADIO_EDGE,
MAC802154_HWSIM_EDGE_ATTR_ENDPOINT_ID and MAC802154_HWSIM_EDGE_ATTR_LQI
must be present to fix GPF.
Fixes: f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Acked-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20210705131321.217111-1-mudongliangabcd@gmail.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
There are a few scenarios where init_active_labels() can return without
registering deactivate_labels() to run when the region is disabled. In
particular label error injection creates scenarios where a DIMM is
disabled, but labels on other DIMMs in the region become activated.
Arrange for init_active_labels() to always register deactivate_labels().
Reported-by: Krzysztof Kensicki <krzysztof.kensicki@intel.com> Cc: <stable@vger.kernel.org> Fixes: bf9bccc14c05 ("libnvdimm: pmem label sets and namespace instantiation.") Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Link: https://lore.kernel.org/r/162766356450.3223041.1183118139023841447.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Fix the NFIT parsing code to treat a 0 index in a SPA Range Structure as
a special case and not match Region Mapping Structures that use 0 to
indicate that they are not mapped. Without this fix some platform BIOS
descriptions of "virtual disk" ranges do not result in the pmem driver
attaching to the range.
Details:
In addition to typical persistent memory ranges, the ACPI NFIT may also
convey "virtual" ranges. These ranges are indicated by a UUID in the SPA
Range Structure of UUID_VOLATILE_VIRTUAL_DISK, UUID_VOLATILE_VIRTUAL_CD,
UUID_PERSISTENT_VIRTUAL_DISK, or UUID_PERSISTENT_VIRTUAL_CD. The
critical difference between virtual ranges and UUID_PERSISTENT_MEMORY,
is that virtual do not support associations with Region Mapping
Structures. For this reason the "index" value of virtual SPA Range
Structures is allowed to be 0. If a platform BIOS decides to represent
NVDIMMs with disconnected "Region Mapping Structures" (range-index ==
0), the kernel may falsely associate them with standalone ranges where
the "SPA Range Structure Index" is also zero. When this happens the
driver may falsely require labels where "virtual disks" are expected to
be label-less. I.e. "label-less" is where the namespace-range ==
region-range and the pmem driver attaches with no user action to create
a namespace.
Cc: Jacek Zloch <jacek.zloch@intel.com> Cc: Lukasz Sobieraj <lukasz.sobieraj@intel.com> Cc: "Lee, Chun-Yi" <jlee@suse.com> Cc: <stable@vger.kernel.org> Fixes: c2f32acdf848 ("acpi, nfit: treat virtual ramdisk SPA as pmem region") Reported-by: Krzysztof Rusocki <krzysztof.rusocki@intel.com> Reported-by: Damian Bassa <damian.bassa@intel.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Link: https://lore.kernel.org/r/162870796589.2521182.1240403310175570220.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
Function ceph_check_delayed_caps() is called from the mdsc->delayed_work
workqueue and it can be kept looping for quite some time if caps keep
being added back to the mdsc->cap_delay_list. This may result in the
watchdog tainting the kernel with the softlockup flag.
This patch breaks this loop if the caps have been recently (i.e. during
the loop execution). Any new caps added to the list will be handled in
the next run.
Also, allow schedule_delayed() callers to explicitly set the delay value
instead of defaulting to 5s, so we can ensure that it runs soon
afterward if it looks like there is more work.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/46284 Signed-off-by: Luis Henriques <lhenriques@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
If an i2c driver happens to not provide the full amount of data that a
user asks for, it is possible that some uninitialized data could be sent
to userspace. While all in-kernel drivers look to be safe, just be sure
by initializing the buffer to zero before it is passed to the i2c driver
so that any future drivers will not have this issue.
Also properly copy the amount of data recvieved to the userspace buffer,
as pointed out by Dan Carpenter.
Reported-by: Eric Dumazet <edumazet@google.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kelsey Skunberg <kelsey.skunberg@canonical.com>
projects / mirror_ubuntu-focal-kernel.git / log