Signed-off-by: Christian Eggers <ceggers@arri.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200728092959.24600-1-ceggers@arri.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
The ES58X devices has a CDC ACM interface (used for debug
purpose). During probing, the device is thus recognized as USB Modem
(CDC ACM), preventing the etas-es58x module to load:
usbcore: registered new interface driver etas_es58x
usb 1-1.1: new full-speed USB device number 14 using xhci_hcd
usb 1-1.1: New USB device found, idVendor=108c, idProduct=0159, bcdDevice= 1.00
usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.1: Product: ES581.4
usb 1-1.1: Manufacturer: ETAS GmbH
usb 1-1.1: SerialNumber: 2204355
cdc_acm 1-1.1:1.0: No union descriptor, testing for castrated device
cdc_acm 1-1.1:1.0: ttyACM0: USB ACM device
Thus, these have been added to the ignore list in
drivers/usb/class/cdc-acm.c
N.B. Future firmware release of the ES58X will remove the CDC-ACM
interface.
`lsusb -v` of the three devices variant (ES581.4, ES582.1 and
ES584.1):
Bus 001 Device 011: ID 108c:0159 Robert Bosch GmbH ES581.4
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0159
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES581.4
iSerial 3 2204355
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0035
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 5 Bus Powered Configuration
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 4 ACM Control Interface
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x01
call management
bDataInterface 0
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 10
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 012: ID 108c:0168 Robert Bosch GmbH ES582
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0168
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES582
iSerial 3 0108933
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 013: ID 108c:0169 Robert Bosch GmbH ES584.1
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0169
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES584.1
iSerial 3 0100320
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201002154219.4887-8-mailhol.vincent@wanadoo.fr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
Suggested-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The only time that our Bridgeport role should change is when we change
the configuration ourselves. In which case we also adjust our internal
state tracking, no need to do it again when we receive the corresponding
event.
Removing the locked section helps a subsequent patch that needs to flush
the workqueue while under sbp_lock.
It would be nice to raise a warning here in case HW does weird things
after all, but this could end up generating false-positives when we
change the configuration ourselves.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The idx in __ath10k_htt_rx_ring_fill_n function lives in
consistent dma region writable by the device. Malfunctional
or malicious device could manipulate such idx to have a OOB
write. Either by
htt->rx_ring.netbufs_ring[idx] = skb;
or by
ath10k_htt_set_paddrs_ring(htt, paddr, idx);
The idx can also be negative as it's signed, giving a large
memory space to write to.
It's possibly exploitable by corruptting a legit pointer with
a skb pointer. And then fill skb with payload as rougue object.
Part of the log here. Sometimes it appears as UAF when writing
to a freed memory by chance.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200623221105.3486-1-bruceshenzk@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
CFGx.FIFO_MODE field controls a DMA-controller "FIFO readiness" criterion.
In other words it determines when to start pushing data out of a DW
DMAC channel FIFO to a destination peripheral or from a source
peripheral to the DW DMAC channel FIFO. Currently FIFO-mode is set to one
for all DW DMAC channels. It means they are tuned to flush data out of
FIFO (to a memory peripheral or by accepting the burst transaction
requests) when FIFO is at least half-full (except at the end of the block
transfer, when FIFO-flush mode is activated) and are configured to get
data to the FIFO when it's at least half-empty.
Such configuration is a good choice when there is no slave device involved
in the DMA transfers. In that case the number of bursts per block is less
than when CFGx.FIFO_MODE = 0 and, hence, the bus utilization will improve.
But the latency of DMA transfers may increase when CFGx.FIFO_MODE = 1,
since DW DMAC will wait for the channel FIFO contents to be either
half-full or half-empty depending on having the destination or the source
transfers. Such latencies might be dangerous in case if the DMA transfers
are expected to be performed from/to a slave device. Since normally
peripheral devices keep data in internal FIFOs, any latency at some
critical moment may cause one being overflown and consequently losing
data. This especially concerns a case when either a peripheral device is
relatively fast or the DW DMAC engine is relatively slow with respect to
the incoming data pace.
In order to solve problems, which might be caused by the latencies
described above, let's enable the FIFO half-full/half-empty "FIFO
readiness" criterion only for DMA transfers with no slave device involved.
Thanks to the commit 99ba8b9b0d97 ("dmaengine: dw: Initialize channel
before each transfer") we can freely do that in the generic
dw_dma_initialize_chan() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200731200826.9292-3-Sergey.Semin@baikalelectronics.ru Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
DW DMA IP-core provides a way to synthesize the DMA controller with
channels having different parameters like maximum burst-length,
multi-block support, maximum data width, etc. Those parameters both
explicitly and implicitly affect the channels performance. Since DMA slave
devices might be very demanding to the DMA performance, let's provide a
functionality for the slaves to be assigned with DW DMA channels, which
performance according to the platform engineer fulfill their requirements.
After this patch is applied it can be done by passing the mask of suitable
DMA-channels either directly in the dw_dma_slave structure instance or as
a fifth cell of the DMA DT-property. If mask is zero or not provided, then
there is no limitation on the channels allocation.
For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first
two channels are synthesized with max burst length of 16, while the rest
of the channels have been created with max-burst-len=4. It would seem that
the first two channels must be faster than the others and should be more
preferable for the time-critical DMA slave devices. In practice it turned
out that the situation is quite the opposite. The channels with
max-burst-len=4 demonstrated a better performance than the channels with
max-burst-len=16 even when they both had been initialized with the same
settings. The performance drop of the first two DMA-channels made them
unsuitable for the DW APB SSI slave device. No matter what settings they
are configured with, full-duplex SPI transfers occasionally experience the
Rx FIFO overflow. It means that the DMA-engine doesn't keep up with
incoming data pace even though the SPI-bus is enabled with speed of 25MHz
while the DW DMA controller is clocked with 50MHz signal. There is no such
problem has been noticed for the channels synthesized with
max-burst-len=4.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ru Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If ufs_qcom_dump_dbg_regs() calls ufs_qcom_testbus_config() from
ufshcd_suspend/resume and/or clk gate/ungate context, pm_runtime_get_sync()
and ufshcd_hold() will cause a race condition. Fix this by removing the
unnecessary calls of pm_runtime_get_sync() and ufshcd_hold().
Link: https://lore.kernel.org/r/1596975355-39813-3-git-send-email-cang@codeaurora.org Reviewed-by: Hongwu Su <hongwus@codeaurora.org> Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
usb_kill_anchored_urbs() is commonly used to cancel all URBs on an
anchor just before releasing resources which the URBs rely on. By doing
so, users of this function rely on that no completer callbacks will take
place from any URB on the anchor after it returns.
However if this function is called in parallel with __usb_hcd_giveback_urb
processing a URB on the anchor, the latter may call the completer
callback after usb_kill_anchored_urbs() returns. This can lead to a
kernel panic due to use after release of memory in interrupt context.
The race condition is that __usb_hcd_giveback_urb() first unanchors the URB
and then makes the completer callback. Such URB is hence invisible to
usb_kill_anchored_urbs(), allowing it to return before the completer has
been called, since the anchor's urb_list is empty.
Even worse, if the racing completer callback resubmits the URB, it may
remain in the system long after usb_kill_anchored_urbs() returns.
Hence list_empty(&anchor->urb_list), which is used in the existing
while-loop, doesn't reliably ensure that all URBs of the anchor are gone.
A similar problem exists with usb_poison_anchored_urbs() and
usb_scuttle_anchored_urbs().
This patch adds an external do-while loop, which ensures that all URBs
are indeed handled before these three functions return. This change has
no effect at all unless the race condition occurs, in which case the
loop will busy-wait until the racing completer callback has finished.
This is a rare condition, so the CPU waste of this spinning is
negligible.
The additional do-while loop relies on usb_anchor_check_wakeup(), which
returns true iff the anchor list is empty, and there is no
__usb_hcd_giveback_urb() in the system that is in the middle of the
unanchor-before-complete phase. The @suspend_wakeups member of
struct usb_anchor is used for this purpose, which was introduced to solve
another problem which the same race condition causes, in commit 6ec4147e7bdb ("usb-anchor: Delay usb_wait_anchor_empty_timeout wake up
till completion is done").
The surely_empty variable is necessary, because usb_anchor_check_wakeup()
must be called with the lock held to prevent races. However the spinlock
must be released and reacquired if the outer loop spins with an empty
URB list while waiting for the unanchor-before-complete passage to finish:
The completer callback may very well attempt to take the very same lock.
To summarize, using usb_anchor_check_wakeup() means that the patched
functions can return only when the anchor's list is empty, and there is
no invisible URB being processed. Since the inner while loop finishes on
the empty list condition, the new do-while loop will terminate as well,
except for when the said race condition occurs.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200731054650.30644-1-eli.billauer@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When brcmf_proto_msgbuf_attach fail and msgbuf->txflow_wq != NULL,
we should destroy the workqueue.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Yufen <wangyufen@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1595237765-66238-1-git-send-email-wangyufen@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Eliminate kernel panics when getting invalid responses from controller.
Take controller offline instead of causing kernel panics.
Link: https://lore.kernel.org/r/159622929306.30579.16523318707596752828.stgit@brunhilda Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Prasad Munirathnam <Prasad.Munirathnam@microsemi.com> Reviewed-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
syzbot is reporting that del_timer_sync() is called from
mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without
checking timer_setup() from mwifiex_usb_tx_init() was called [1].
Ganapathi Bhat proposed a possibly cleaner fix, but it seems that
that fix was forgotten [2].
"grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that
currently there are 28 locations which call del_timer[_sync]() only if
that timer's function field was initialized (because timer_setup() sets
that timer's function field). Therefore, let's use same approach here.
When a usrjquota or grpjquota mount option is used multiple times, we
will leak memory allocated for the file name. Make sure the last setting
is used and all the previous ones are properly freed.
Reported-by: syzbot+c9e294bbe0333a6b7640@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When kmalloc() on buf fails, urb should be freed just like
when kmalloc() on dr fails.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
A fb_ioctl() FBIOPUT_VSCREENINFO call with invalid xres setting
or yres setting in struct fb_var_screeninfo will result in a
KASAN: vmalloc-out-of-bounds failure in bitfill_aligned() as
the margins are being cleared. The margins are cleared in
chunks and if the xres setting or yres setting is a value of
zero upto the chunk size, the failure will occur.
Add a margin check to validate xres and yres settings.
Signed-off-by: George Kennedy <george.kennedy@oracle.com> Reported-by: syzbot+e5fd3e65515b48c02a30@syzkaller.appspotmail.com Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Dhaval Giani <dhaval.giani@oracle.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1594149963-13801-1-git-send-email-george.kennedy@oracle.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
While aborting the I/O, the firmware cleanup task timed out and driver
deleted the I/O from active command list. Some time later the firmware
sent the cleanup task response and driver again deleted the I/O from
active command list causing firmware to send completion for non-existent
I/O and list_del corruption of active command list.
Add fix to check if I/O is present before deleting it from the active
command list to ensure firmware sends valid I/O completion and protect
against list_del corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-4-mrangankar@marvell.com Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Protect active command list for non-I/O commands like login response,
logout response, text response, and recovery cleanup of active list to
avoid list corruption.
Link: https://lore.kernel.org/r/20200908095657.26821-5-mrangankar@marvell.com Signed-off-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If SUCCESS is not returned, error handling will escalate. Return SUCCESS
similar to other conditions in this function.
Link: https://lore.kernel.org/r/20200907121443.5150-6-jhasan@marvell.com Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Javed Hasan <jhasan@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The Acer One S1003 2-in-1 keyboard dock uses a Synaptics S910xx touchpad
which is connected to an ITE 8910 USB keyboard controller chip.
This keyboard has the same quirk for its rfkill / airplane mode hotkey as
other keyboards with ITE keyboard chips, it only sends a single release
event when pressed and released, it never sends a press event.
This commit adds this keyboards USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard. Note that like for the
Acer Aspire Switch 10 (SW5-012) the id-table entry matches on the
HID_GROUP_GENERIC generic group so that hid-ite only binds to the
keyboard interface and the mouse/touchpad interface is left untouched
so that hid-multitouch can bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Free the skb if usb_submit_urb fails on rx_urb. And free the urb
no matter usb_submit_urb succeeds or not in rtl8xxxu_submit_int_urb.
Signed-off-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200906040424.22022-1-chiu@endlessm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When wlc_phy_txpwr_srom_read_lcnphy fails in wlc_phy_attach_lcnphy,
the allocated pi->u.pi_lcnphy is leaked, since struct brcms_phy will be
freed in the caller function.
Fix this by calling wlc_phy_detach_lcnphy in the error handler of
wlc_phy_txpwr_srom_read_lcnphy before returning.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200908121743.23108-1-keitasuzuki.park@sslab.ics.keio.ac.jp Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Andrii reported that with latest clang, when building selftests, we have
error likes:
error: progs/test_sysctl_loop1.c:23:16: in function sysctl_tcp_mem i32 (%struct.bpf_sysctl*):
Looks like the BPF stack limit of 512 bytes is exceeded.
Please move large on stack variables into BPF per-cpu array map.
The error is triggered by the following LLVM patch:
https://reviews.llvm.org/D87134
For example, the following code is from test_sysctl_loop1.c:
static __always_inline int is_tcp_mem(struct bpf_sysctl *ctx)
{
volatile char tcp_mem_name[] = "net/ipv4/tcp_mem/very_very_very_very_long_pointless_string";
...
}
Without the above LLVM patch, the compiler did optimization to load the string
(59 bytes long) with 7 64bit loads, 1 8bit load and 1 16bit load,
occupying 64 byte stack size.
With the above LLVM patch, the compiler only uses 8bit loads, but subregister is 32bit.
So stack requirements become 4 * 59 = 236 bytes. Together with other stuff on
the stack, total stack size exceeds 512 bytes, hence compiler complains and quits.
To fix the issue, removing "volatile" key word or changing "volatile" to
"const"/"static const" does not work, the string is put in .rodata.str1.1 section,
which libbpf did not process it and errors out with
libbpf: elf: skipping unrecognized data section(6) .rodata.str1.1
libbpf: prog 'sysctl_tcp_mem': bad map relo against '.L__const.is_tcp_mem.tcp_mem_name'
in section '.rodata.str1.1'
Defining the string const as global variable can fix the issue as it puts the string constant
in '.rodata' section which is recognized by libbpf. In the future, when libbpf can process
'.rodata.str*.*' properly, the global definition can be changed back to local definition.
Defining tcp_mem_name as a global, however, triggered a verifier failure.
./test_progs -n 7/21
libbpf: load bpf program failed: Permission denied
libbpf: -- BEGIN DUMP LOG ---
libbpf:
invalid stack off=0 size=1
verification time 6975 usec
stack depth 160+64
processed 889 insns (limit 1000000) max_states_per_insn 4 total_states
14 peak_states 14 mark_read 10
libbpf: -- END LOG --
libbpf: failed to load program 'sysctl_tcp_mem'
libbpf: failed to load object 'test_sysctl_loop2.o'
test_bpf_verif_scale:FAIL:114
#7/21 test_sysctl_loop2.o:FAIL
This actually exposed a bpf program bug. In test_sysctl_loop{1,2}, we have code
like
const char tcp_mem_name[] = "<...long string...>";
...
char name[64];
...
for (i = 0; i < sizeof(tcp_mem_name); ++i)
if (name[i] != tcp_mem_name[i])
return 0;
In the above code, if sizeof(tcp_mem_name) > 64, name[i] access may be
out of bound. The sizeof(tcp_mem_name) is 59 for test_sysctl_loop1.c and
79 for test_sysctl_loop2.c.
Without promotion-to-global change, old compiler generates code where
the overflowed stack access is actually filled with valid value, so hiding
the bpf program bug. With promotion-to-global change, the code is different,
more specifically, the previous loading constants to stack is gone, and
"name" occupies stack[-64:0] and overflow access triggers a verifier error.
To fix the issue, adjust "name" buffer size properly.
Reported-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Yonghong Song <yhs@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/20200909171542.3673449-1-yhs@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Emit a warning when ->done or ->free are called on an already freed
srb. There is a hidden use-after-free bug in the driver which corrupts
the srb memory pool which originates from the cleanup callbacks.
An extensive search didn't bring any lights on the real problem. The
initial fix was to set both pointers to NULL and try to catch invalid
accesses. But instead the memory corruption was gone and the driver
didn't crash. Since not all calling places check for NULL pointer, add
explicitly default handlers. With this we workaround the memory
corruption and add a debug help.
Link: https://lore.kernel.org/r/20200908081516.8561-2-dwagner@suse.de Reviewed-by: Martin Wilck <mwilck@suse.com> Reviewed-by: Arun Easi <aeasi@marvell.com> Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
It is trivial to trigger a WARN_ON_ONCE(1) in iomap_dio_actor() by
unprivileged users which would taint the kernel, or worse - panic if
panic_on_warn or panic_on_taint is set. Hence, just convert it to
pr_warn_ratelimited() to let users know their workloads are racing.
Thank Dave Chinner for the initial analysis of the racing reproducers.
Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
It's allocating an array of a6xx_gpu_state_obj structure rathor than
its pointers.
This patch fix it.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Since l2cap_sock_teardown_cb doesn't acquire the channel lock before
setting the socket as zapped, it could potentially race with
l2cap_sock_release which frees the socket. Thus, wait until the cleanup
is complete before marking the socket as zapped.
This race was reproduced on a JBL GO speaker after the remote device
rejected L2CAP connection due to resource unavailability.
Here is a dmesg log with debug logs from a repro of this bug:
[ 3465.424086] Bluetooth: hci_core.c:hci_acldata_packet() hci0 len 16 handle 0x0003 flags 0x0002
[ 3465.424090] Bluetooth: hci_conn.c:hci_conn_enter_active_mode() hcon 00000000cfedd07d mode 0
[ 3465.424094] Bluetooth: l2cap_core.c:l2cap_recv_acldata() conn 000000007eae8952 len 16 flags 0x2
[ 3465.424098] Bluetooth: l2cap_core.c:l2cap_recv_frame() len 12, cid 0x0001
[ 3465.424102] Bluetooth: l2cap_core.c:l2cap_raw_recv() conn 000000007eae8952
[ 3465.424175] Bluetooth: l2cap_core.c:l2cap_sig_channel() code 0x03 len 8 id 0x0c
[ 3465.424180] Bluetooth: l2cap_core.c:l2cap_connect_create_rsp() dcid 0x0045 scid 0x0000 result 0x02 status 0x00
[ 3465.424189] Bluetooth: l2cap_core.c:l2cap_chan_put() chan 000000006acf9bff orig refcnt 4
[ 3465.424196] Bluetooth: l2cap_core.c:l2cap_chan_del() chan 000000006acf9bff, conn 000000007eae8952, err 111, state BT_CONNECT
[ 3465.424203] Bluetooth: l2cap_sock.c:l2cap_sock_teardown_cb() chan 000000006acf9bff state BT_CONNECT
[ 3465.424221] Bluetooth: l2cap_core.c:l2cap_chan_put() chan 000000006acf9bff orig refcnt 3
[ 3465.424226] Bluetooth: hci_core.h:hci_conn_drop() hcon 00000000cfedd07d orig refcnt 6
[ 3465.424234] BUG: spinlock bad magic on CPU#2, kworker/u17:0/159
[ 3465.425626] Bluetooth: hci_sock.c:hci_sock_sendmsg() sock 000000002bb0cb64 sk 00000000a7964053
[ 3465.430330] lock: 0xffffff804410aac0, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[ 3465.430332] Causing a watchdog bite!
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Reported-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Reviewed-by: Manish Mandlik <mmandlik@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Some integrated OHCI controller hubs do not expose all ports of the hub
to pins on the SoC. In some cases the unconnected ports generate
spurious over-current events. For example the Broadcom 56060/Ranger 2 SoC
contains a nominally 3 port hub but only the first port is wired.
Default behaviour for ohci-platform driver is to use global over-current
protection mode (AKA "ganged"). This leads to the spurious over-current
events affecting all ports in the hub.
We now alter the default to use per-port over-current protection.
This patch results in the following configuration changes depending
on quirks:
- For quirk OHCI_QUIRK_SUPERIO no changes. These systems remain set up
for ganged power switching and no over-current protection.
- For quirk OHCI_QUIRK_AMD756 or OHCI_QUIRK_HUB_POWER power switching
remains at none, while over-current protection is now guaranteed to be
set to per-port rather than the previous behaviour where it was either
none or global over-current protection depending on the value at
function entry.
Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz> Link: https://lore.kernel.org/r/20200910212512.16670-1-hamish.martin@alliedtelesis.co.nz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
There's an overflow bug in the realtime allocator. If the rt volume is
large enough to handle a single allocation request that is larger than
the maximum bmap extent length and the rt bitmap ends exactly on a
bitmap block boundary, it's possible that the near allocator will try to
check the freeness of a range that extends past the end of the bitmap.
This fails with a corruption error and shuts down the fs.
Therefore, constrain maxlen so that the range scan cannot run off the
end of the rt bitmap.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If dev_pm_opp_attach_genpd() is called multiple times (once for each CPU
sharing the table), then it would result in unwanted behavior like
memory leak, attaching the domain multiple times, etc.
Handle that by checking and returning earlier if the domains are already
attached. Now that dev_pm_opp_detach_genpd() can get called multiple
times as well, we need to protect that too.
Note that the virtual device pointers aren't returned in this case, as
they may become unavailable to some callers during the middle of the
operation.
Reported-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
unlock_new_inode() is only meant to be called after a new inode has
already been inserted into the hash table. But reiserfs_new_inode() can
call it even before it has inserted the inode, triggering the WARNING in
unlock_new_inode(). Fix this by only calling unlock_new_inode() if the
inode has the I_NEW flag set, indicating that it's in the table.
This addresses the syzbot report "WARNING in unlock_new_inode"
(https://syzkaller.appspot.com/bug?extid=187510916eb6a14598f7).
Link: https://lore.kernel.org/r/20200628070057.820213-1-ebiggers@kernel.org Reported-by: syzbot+187510916eb6a14598f7@syzkaller.appspotmail.com Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Protect against potential stack overflow that might happen when bpf2bpf
calls get combined with tailcalls. Limit the caller's stack depth for
such case down to 256 so that the worst case scenario would result in 8k
stack size (32 which is tailcall limit * 256 = 8k).
Suggested-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The T820, G31 & G52 GPUs integrated by Amlogic in the respective GXM,
G12A/SM1 & G12B SoCs needs a quirk in the PWR registers at the GPU reset
time.
Since the Amlogic's integration of the GPU cores with the SoC is not
publicly documented we do not know what does these values, but they
permit having a fully functional GPU running with Panfrost.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[Steven: Fix typo in commit log] Reviewed-by: Steven Price <steven.price@arm.com> Reviewed-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com> Signed-off-by: Steven Price <steven.price@arm.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200916150147.25753-3-narmstrong@baylibre.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Calls to usb_kill_anchored_urbs() after usb_kill_urb() on multiprocessor
systems create a race condition in which usb_kill_anchored_urbs() deallocates
the URB before the completer callback is called in usb_kill_urb(), resulting
in a use-after-free.
To fix this, add proper lock protection to usb_kill_urb() calls that can
possibly run concurrently with usb_kill_anchored_urbs().
This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.
Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: introduce flexcan_chip_stop_disable_on_error() and use it in flexcan_close()] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/r/20200922144429.2613631-11-mkl@pengutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Handle broken union functional descriptors where the master-interface
doesn't exist or where its class is of neither Communication or Data
type (as required by the specification) by falling back to
"combined-interface" probing.
Note that this still allows for handling union descriptors with switched
interfaces.
This specifically makes the Whistler radio scanners TRX series devices
work with the driver without adding further quirks to the device-id
table.
Reported-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com> Tested-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200921135951.24045-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The vht capability of MAX_MPDU_LENGTH is 11454 in rtw88; however, the rx
buffer size for each packet is 8192. When receiving packets that are
larger than rx buffer size, it will leads to rx buffer ring overflow.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200925061219.23754-2-tehuang@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When we fail to read inode, some data accessed in udf_evict_inode() may
be uninitialized. Move the accesses to !is_bad_inode() branch.
Reported-by: syzbot+91f02b28f9bb5f5f1341@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Although UDF standard allows it, we don't support sparing table larger
than a single block. Check it during mount so that we don't try to
access memory beyond end of buffer.
Reported-by: syzbot+9991561e714f597095da@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
BUG: KASAN: use-after-free in __lock_acquire+0x3fd4/0x4180
kernel/locking/lockdep.c:3831
Read of size 8 at addr ffff8880683b0018 by task syz-executor.0/3377
Reported-by: Kyungtae Kim <kt0755@gmail.com> Signed-off-by: Zqiang <qiang.zhang@windriver.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Since struct _mic_vring_info and vring are allocated together and follow
vring, if the vring_size() is not four bytes aligned, which will cause
the start address of struct _mic_vring_info is not four byte aligned.
For example, when vring entries is 128, the vring_size() will be 5126
bytes. The _mic_vring_info struct layout in ddr looks like:
0x90002400: 0000000000390000EE0100000000C0FF
Here 0x39 is the avail_idx member, and 0xC0FFEE01 is the magic member.
When EP use ioread32(magic) to reads the magic in RC's share memory, it
will cause kernel panic on ARM64 platform due to the cross-byte io read.
Here read magic in user space use le32toh(vr0->info->magic) will meet
the same issue.
So add round_up(x,4) for vring_size, then the struct _mic_vring_info
will store in this way:
0x90002400: 000000000000000000000039C0FFEE01
Which will avoid kernel panic when read magic in struct _mic_vring_info.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Link: https://lore.kernel.org/r/20200929091106.24624-4-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
trace-cmd report doesn't show events from target subsystem because
scsi_command_size() leaks through event format string:
[target:target_sequencer_start] function scsi_command_size not defined
[target:target_cmd_complete] function scsi_command_size not defined
Addition of scsi_command_size() to plugin_scsi.c in trace-cmd doesn't
help because an expression is used inside TP_printk(). trace-cmd event
parser doesn't understand minus sign inside [ ]:
Error: expected ']' but read '-'
Rather than duplicating kernel code in plugin_scsi.c, provide a dedicated
field for CONTROL byte.
Link: https://lore.kernel.org/r/20200929125957.83069-1-r.bolshakov@yadro.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Return PTR_ERR() from the error handling case instead of 0.
Link: https://lore.kernel.org/r/20200910123848.93649-1-jingxiangfeng@huawei.com Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
get_gendisk grabs a reference on the disk and file operation, so this
code will leak both of them while having absolutely no use for the
gendisk itself.
This effectively reverts commit 2df83fa4bce421f ("PM / Hibernate: Use
get_gendisk to verify partition if resume_file is integer format")
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Even though a driver or mac80211 shouldn't produce a
legacy bitrate if sband->bitrates doesn't exist, don't
crash if that is the case either.
This fixes a kernel panic if station dump is run before
last_rate can be updated with a data frame when
sband->bitrates is missing (eg. in S1G bands).
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20201005164522.18069-1-thomas@adapt-ip.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
GRE tunnel has its own header_ops, ipgre_header_ops, and sets it
conditionally. When it is set, it assumes the outer IP header is
already created before ipgre_xmit().
This is not true when we send packets through a raw packet socket,
where L2 headers are supposed to be constructed by user. Packet
socket calls dev_validate_header() to validate the header. But
GRE tunnel does not set dev->hard_header_len, so that check can
be simply bypassed, therefore uninit memory could be passed down
to ipgre_xmit(). Similar for dev->needed_headroom.
dev->hard_header_len is supposed to be the length of the header
created by dev->header_ops->create(), so it should be used whenever
header_ops is set, and dev->needed_headroom should be used when it
is not set.
Reported-and-tested-by: syzbot+4a2c52677a8a1aa283cb@syzkaller.appspotmail.com Cc: William Tu <u9012063@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Number of bytes allocated for mft record should be equal to the mft record
size stored in ntfs superblock as reported by syzbot, userspace might
trigger out-of-bounds read by dereferencing ctx->attr in ntfs_attr_find()
Reported-by: syzbot+aed06913f36eff9b544e@syzkaller.appspotmail.com Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: syzbot+aed06913f36eff9b544e@syzkaller.appspotmail.com Acked-by: Anton Altaparmakov <anton@tuxera.com> Link: https://syzkaller.appspot.com/bug?extid=aed06913f36eff9b544e Link: https://lkml.kernel.org/r/20200824022804.226242-1-rkovhaev@gmail.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced. For other error
paths after this call, things are the same.
Fix this by adding pm_runtime_put_noidle() after 'err_runtime_disable'
label. But in this case, the error path after pm_runtime_put_sync()
will decrease PM usage counter twice. Thus add an extra
pm_runtime_get_noresume() in this path to balance PM counter.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The patch just remembers the "nodes" entry pointer in space as I think
it's created as subdirectory when parent "spaces" is created. In
function drop_space() we will lost the pointer reference to nds because
configfs_remove_default_groups(). However as this subdirectory is always
available when "spaces" exists it will just be freed when "spaces" will be
freed.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
There are few list handling issues while adding and deleting
node in the registered buf list in the driver.
1. list addition - buffer added into the list during buf_init
while not deleted during cleanup.
2. list deletion - In capture streamoff, the list was reinitialized.
As a result, if any node was present in the list, it would
lead to issue while cleaning up that node during buf_cleanup.
bFrameIndex and bFormatIndex can be negotiated by the camera during
probing, resulting in the camera choosing a different format than
expected. v4l2 can already accommodate such changes, but the code was
not updating the proper fields.
Without such a change, v4l2 would potentially interpret the payload
incorrectly, causing corrupted output. This was happening on the
Elgato HD60 S+, which currently always renegotiates to format 1.
As an aside, the Elgato firmware is buggy and should not be renegotating,
but it is still a valid thing for the camera to do. Both macOS and Windows
will properly probe and read uncorrupted images from this camera.
With this change, both qv4l2 and chromium can now read uncorrupted video
from the Elgato HD60 S+.
[Add blank lines, remove periods at the of messages]
Signed-off-by: Adam Goode <agoode@google.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If an exception needs to be handled while reading an MSR - which is in
most of the cases caused by a #GP on a non-existent MSR - then this
is most likely the incarnation of a BIOS or a hardware bug. Such bug
violates the architectural guarantee that MCA banks are present with all
MSRs belonging to them.
The proper fix belongs in the hardware/firmware - not in the kernel.
Handling an #MC exception which is raised while an NMI is being handled
would cause the nasty NMI nesting issue because of the shortcoming of
IRET of reenabling NMIs when executed. And the machine is in an #MC
context already so <Deity> be at its side.
Tracing MSR accesses while in #MC is another no-no due to tracing being
inherently a bad idea in atomic context:
vmlinux.o: warning: objtool: do_machine_check()+0x4a: call to mce_rdmsrl() leaves .noinstr.text section
so remove all that "additional" functionality from mce_rdmsrl() and
provide it with a special exception handler which panics the machine
when that MSR is not accessible.
The exception handler prints a human-readable message explaining what
the panic reason is but, what is more, it panics while in the #GP
handler and latter won't have executed an IRET, thus opening the NMI
nesting issue in the case when the #MC has happened while handling
an NMI. (#MC itself won't be reenabled until MCG_STATUS hasn't been
cleared).
Suggested-by: Andy Lutomirski <luto@kernel.org> Suggested-by: Peter Zijlstra <peterz@infradead.org>
[ Add missing prototypes for ex_handler_* ] Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Tony Luck <tony.luck@intel.com> Link: https://lkml.kernel.org/r/20200906212130.GA28456@zn.tnic Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
In bttv_probe if some functions such as pci_enable_device,
pci_set_dma_mask and request_mem_region fails the allocated
memory for btv should be released.
Signed-off-by: Xiaolong Huang <butterflyhuangxx@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Also, call pm_runtime_disable() when pm_runtime_get_sync() returns
an error code.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Signed-off-by: Qiushi Wu <wu000273@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
delta_run_work() calls delta_get_sync() that increments
the reference counter. In case of failure, decrement the reference
count by calling delta_put_autosuspend().
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If you do sanity checks, you should do them for both endpoints.
Hence introduce checking for endpoint type for the output
endpoint, too.
Reported-by: syzbot+998261c2ae5932458f6c@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The patrol scrubber in Skylake and Cascade Lake systems can be configured
to report uncorrected errors using a special signature in the machine
check bank and to signal using CMCI instead of machine check.
Update the severity calculation mechanism to allow specifying the model,
minimum stepping and range of machine check bank numbers.
Add a new rule to detect the special signature (on model 0x55, stepping
>=4 in any of the memory controller banks).
[ bp: Rewrite it.
aegl: Productize it. ]
Suggested-by: Youquan Song <youquan.song@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Co-developed-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20200930021313.31810-2-tony.luck@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The CRn accessor functions use __force_order as a dummy operand to
prevent the compiler from reordering CRn reads/writes with respect to
each other.
The fact that the asm is volatile should be enough to prevent this:
volatile asm statements should be executed in program order. However GCC
4.9.x and 5.x have a bug that might result in reordering. This was fixed
in 8.1, 7.3 and 6.5. Versions prior to these, including 5.x and 4.9.x,
may reorder volatile asm statements with respect to each other.
There are some issues with __force_order as implemented:
- It is used only as an input operand for the write functions, and hence
doesn't do anything additional to prevent reordering writes.
- It allows memory accesses to be cached/reordered across write
functions, but CRn writes affect the semantics of memory accesses, so
this could be dangerous.
- __force_order is not actually defined in the kernel proper, but the
LLVM toolchain can in some cases require a definition: LLVM (as well
as GCC 4.9) requires it for PIE code, which is why the compressed
kernel has a definition, but also the clang integrated assembler may
consider the address of __force_order to be significant, resulting in
a reference that requires a definition.
Fix this by:
- Using a memory clobber for the write functions to additionally prevent
caching/reordering memory accesses across CRn writes.
- Using a dummy input operand with an arbitrary constant address for the
read functions, instead of a global variable. This will prevent reads
from being reordered across writes, while allowing memory loads to be
cached/reordered across CRn reads, which should be safe.
Signed-off-by: Pavel Machek (CIP) <pavel@denx.de> Acked-by: John Allen <john.allen@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
syzbot is reporting unkillable task [1], for the caller is failing to
handle a corrupted filesystem image which attempts to access beyond
the end of the device. While we need to fix the caller, flooding the
console with handle_bad_sector() message is unlikely useful.
Callers of get_bitmap_from_slot() are responsible to free the bitmap.
Suggested-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Zhao Heming <heming.zhao@suse.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Commit 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().
But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().
Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.
This fixes the Microsoft Surface Go 2 hanging at boot.
Fixes: 21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()") Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627 Reported-by: Rainer Finke <rainer@finke.cc> Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Suggested-by: Maximilian Luz <luzmaximilian@gmail.com> Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
perf_event.h has macros that define the field offsets in the
data_src bitmask in perf records. The SNOOPX and REMOTE offsets
were both 37. These are distinct fields, and the bitfield layout
in perf_mem_data_src confirms that SNOOPX should be at offset 38.
Fixes: 52839e653b5629bd ("perf tools: Add support for printing new mem_info encodings") Signed-off-by: Al Grant <al.grant@foss.arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Andi Kleen <ak@linux.intel.com> Link: https://lkml.kernel.org/r/4ac9f5cc-4388-b34a-9999-418a4099415d@foss.arm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
765cc3a4b224e ("sched/core: Optimize sched_feat() for !CONFIG_SCHED_DEBUG builds")
made sched features static for !CONFIG_SCHED_DEBUG configurations, but
overlooked the CONFIG_SCHED_DEBUG=y and !CONFIG_JUMP_LABEL cases.
For the latter echoing changes to /sys/kernel/debug/sched_features has
the nasty effect of effectively changing what sched_features reports,
but without actually changing the scheduler behaviour (since different
translation units get different sysctl_sched_features).
Fix CONFIG_SCHED_DEBUG=y and !CONFIG_JUMP_LABEL configurations by properly
restructuring ifdefs.
Fixes: 765cc3a4b224e ("sched/core: Optimize sched_feat() for !CONFIG_SCHED_DEBUG builds") Co-developed-by: Daniel Bristot de Oliveira <bristot@redhat.com> Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com> Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Patrick Bellasi <patrick.bellasi@matbug.net> Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Link: https://lore.kernel.org/r/20201013053114.160628-1-juri.lelli@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
The related system resources were not released when pci_set_dma_mask(),
pci_set_consistent_dma_mask(), or pci_iomap() return error in the
amd_ntb_init_pci() function. Add pci_release_regions() to fix it.
Fixes: a1b3695820aa ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge") Signed-off-by: Kaige Li <likaige@loongson.cn> Signed-off-by: Jon Mason <jdmason@kudzu.us> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When connecting a controller with a zero kato value using the following
command line
nvme connect -t tcp -n NQN -a ADDR -s PORT --keep-alive-tmo=0
the warning below can be reproduced:
WARNING: CPU: 1 PID: 241 at kernel/workqueue.c:1627 __queue_delayed_work+0x6d/0x90
with trace:
mod_delayed_work_on+0x59/0x90
nvmet_update_cc+0xee/0x100 [nvmet]
nvmet_execute_prop_set+0x72/0x80 [nvmet]
nvmet_tcp_try_recv_pdu+0x2f7/0x770 [nvmet_tcp]
nvmet_tcp_io_work+0x63f/0xb2d [nvmet_tcp]
...
This is caused by queuing up an uninitialized work. Althrough the
keep-alive timer is disabled during allocating the controller (fixed in 0d3b6a8d213a), ka_work still has a chance to run (called by
nvmet_start_ctrl).
Fixes: 0d3b6a8d213a ("nvmet: Disable keep-alive timer when kato is cleared to 0h") Signed-off-by: zhenwei pi <pizhenwei@bytedance.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
When an UE or memory error exception is encountered the MCE handler
tries to find the pfn using addr_to_pfn() which takes effective
address as an argument, later pfn is used to poison the page where
memory error occurred, recent rework in this area made addr_to_pfn
to run in real mode, which can be fatal as it may try to access
memory outside RMO region.
Have two helper functions to separate things to be done in real mode
and virtual mode without changing any functionality. This also fixes
the following error as the use of addr_to_pfn is now moved to virtual
mode.
Without this change following kernel crash is seen on hitting UE.
Fixes: 9ca766f9891d ("powerpc/64s/pseries: machine check convert to use common event code") Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200724063946.21378-1-ganeshgr@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
Every dump reported by OPAL is exported to userspace through a sysfs
interface and notified using kobject_uevent(). The userspace daemon
(opal_errd) then reads the dump and acknowledges that the dump is
saved safely to disk. Once acknowledged the kernel removes the
respective sysfs file entry causing respective resources to be
released including kobject.
However it's possible the userspace daemon may already be scanning
dump entries when a new sysfs dump entry is created by the kernel.
User daemon may read this new entry and ack it even before kernel can
notify userspace about it through kobject_uevent() call. If that
happens then we have a potential race between
dump_ack_store->kobject_put() and kobject_uevent which can lead to
use-after-free of a kernfs object resulting in a kernel crash.
This patch fixes this race by protecting the sysfs file
creation/notification by holding a reference count on kobject until we
safely send kobject_uevent().
The function create_dump_obj() returns the dump object which if used
by caller function will end up in use-after-free problem again.
However, the return value of create_dump_obj() function isn't being
used today and there is no need as well. Hence change it to return
void to make this fix complete.
Fixes: c7e64b9ce04a ("powerpc/powernv Platform dump interface") Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20201017164210.264619-1-hegdevasant@linux.vnet.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
There is an off-by-one array check that can lead to a out-of-bounds
write to devices->info[i]. Fix this by checking by using >= rather
than > for the size check. Also replace hard-coded array size limit
with ARRAY_SIZE on the array.
Addresses-Coverity: ("Out-of-bounds write") Fixes: cd9e9808d18f ("lightnvm: Support for Open-Channel SSDs") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
However, the driver from the 3.10 vendor kernel does not use the
following four interrupt lines:
- INT_MALI_PP3
- INT_MALI_PP3_MMU
- INT_MALI_PP7
- INT_MALI_PP7_MMU
Drop the "pp3" and "ppmmu3" interrupt lines. This is also important
because there is no matching entry in interrupt-names for it (meaning
the "pp2" interrupt is actually assigned to the "pp3" interrupt line).
Fixes: 7d3f6b536e72c9 ("ARM: dts: meson8: add the Mali-450 MP6 GPU") Reported-by: Thomas Graichen <thomas.graichen@gmail.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Tested-by: thomas graichen <thomas.graichen@gmail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20200815181957.408649-1-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
DT binding permits only one compatible string which was decribed in past by
commit 63cab195bf49 ("i2c: removed work arounds in i2c driver for Zynq
Ultrascale+ MPSoC").
The commit aea37006e183 ("dt-bindings: i2c: cadence: Migrate i2c-cadence
documentation to YAML") has converted binding to yaml and the following
issues is reported:
...: i2c@ff030000: compatible: Additional items are not allowed
('cdns,i2c-r1p10' was unexpected)
From schema:
.../Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml fds
...: i2c@ff030000: compatible: ['cdns,i2c-r1p14', 'cdns,i2c-r1p10'] is too
long
The commit c415f9e8304a ("ARM64: zynqmp: Fix i2c node's compatible string")
has added the second compatible string but without removing origin one.
The patch is only keeping one compatible string "cdns,i2c-r1p14".
Fixes: c415f9e8304a ("ARM64: zynqmp: Fix i2c node's compatible string") Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/cc294ae1a79ef845af6809ddb4049f0c0f5bb87a.1598259551.git.michal.simek@xilinx.com Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
If cpu_cluster_pm_enter() fails, we need to set MPU power domain back
to enabled to prevent the next WFI from potentially triggering an
undesired MPU power domain state change.
We already do this for omap_enter_idle_smp() but are missing it for
omap_enter_idle_coupled().
Fixes: 55be2f50336f ("ARM: OMAP2+: Handle errors for cpu_pm") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
On error the function was meant to return -ERRNO. This also fixes
compile warning:
drivers/soc/fsl/qbman/bman.c:640:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]
Fixes: 0505d00c8dba ("soc/fsl/qbman: Cleanup buffer pools if BMan was initialized prior to bootup") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Ian May <ian.may@canonical.com>
After commit 7cdf8446ed1d ("arm64: dts: actions: Add pinctrl node for
Actions Semi S700") following error has been observed while booting
Linux on Cubieboard7-lite(based on S700 SoC).
[ 0.257415] pinctrl-s700 e01b0000.pinctrl: can't request region for
resource [mem 0xe01b0000-0xe01b0fff]
[ 0.266902] pinctrl-s700: probe of e01b0000.pinctrl failed with error -16
This is due to the fact that memory range for "sps" power domain controller
clashes with pinctrl.
One way to fix it, is to limit pinctrl address range which is safe
to do as current pinctrl driver uses address range only up to 0x100.
This commit limits the pinctrl address range to 0x100 so that it doesn't
conflict with sps range.
projects / mirror_ubuntu-focal-kernel.git / log