The configuration registers for the LED group have inverted
polarity, which puts the GPIO into open-drain state when used in
GPIO mode. Switch to '0' for GPIO and '1' for LED modes.
Fixes: 87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx") Signed-off-by: Patrick Williams <alpawi@amazon.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191001155154.99710-1-alpawi@amazon.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The 37xx configuration registers are only 32 bits long, so
pins 32-35 spill over into the next register. The calculation
for the register address was done, but the bitmask was not, so
any configuration to pin 32 or above resulted in a bitmask that
overflowed and performed no action.
Fix the register / offset calculation to also adjust the offset.
e3f72b749da2 pinctrl: cherryview: fix Strago DMI workaround 86c5dd6860a6 pinctrl: cherryview: limit Strago DMI workarounds to version 1.0
because even with 1.1 versions of BIOS there are some pins that are
configured as interrupts but not claimed by any driver, and they
sometimes fire up and result in interrupt storms that cause touchpad
stop functioning and other issues.
Given that we are unlikely to qualify another firmware version for a
while it is better to keep the workaround active on all Strago boards.
Reported-by: Alex Levin <levinale@chromium.org> Fixes: 86c5dd6860a6 ("pinctrl: cherryview: limit Strago DMI workarounds to version 1.0") Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Alex Levin <levinale@chromium.org> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Now that there's Hyper-V IOMMU driver, Linux can switch to x2apic mode
when supported by the vcpus.
However, the apic access functions for Hyper-V enlightened apic assume
xapic mode only.
As a result, Linux fails to bring up secondary cpus when run as a guest
in QEMU/KVM with both hv_apic and x2apic enabled.
According to Michael Kelley, when in x2apic mode, the Hyper-V synthetic
apic MSRs behave exactly the same as the corresponding architectural
x2apic MSRs, so there's no need to override the apic accessors. The
only exception is hv_apic_eoi_write, which benefits from lazy EOI when
available; however, its implementation works for both xapic and x2apic
modes.
Check that the per-cpu cluster mask pointer has been set prior to
clearing a dying cpu's bit. The per-cpu pointer is not set until the
target cpu reaches smp_callin() during CPUHP_BRINGUP_CPU, whereas the
teardown function, x2apic_dead_cpu(), is associated with the earlier
CPUHP_X2APIC_PREPARE. If an error occurs before the cpu is awakened,
e.g. if do_boot_cpu() itself fails, x2apic_dead_cpu() will dereference
the NULL pointer and cause a panic.
Our hardware (UV aka Superdome Flex) has address ranges marked
reserved by the BIOS. Access to these ranges is caught as an error,
causing the BIOS to halt the system.
Initial page tables mapped a large range of physical addresses that
were not checked against the list of BIOS reserved addresses, and
sometimes included reserved addresses in part of the mapped range.
Including the reserved range in the map allowed processor speculative
accesses to the reserved range, triggering a BIOS halt.
Used early in booting, the page table level2_kernel_pgt addresses 1
GiB divided into 2 MiB pages, and it was set up to linearly map a full
1 GiB of physical addresses that included the physical address range
of the kernel image, as chosen by KASLR. But this also included a
large range of unused addresses on either side of the kernel image.
And unlike the kernel image's physical address range, this extra
mapped space was not checked against the BIOS tables of usable RAM
addresses. So there were times when the addresses chosen by KASLR
would result in processor accessible mappings of BIOS reserved
physical addresses.
The kernel code did not directly access any of this extra mapped
space, but having it mapped allowed the processor to issue speculative
accesses into reserved memory, causing system halts.
This was encountered somewhat rarely on a normal system boot, and much
more often when starting the crash kernel if "crashkernel=512M,high"
was specified on the command line (this heavily restricts the physical
address of the crash kernel, in our case usually within 1 GiB of
reserved space).
The solution is to invalidate the pages of this table outside the kernel
image's space before the page table is activated. It fixes this problem
on our hardware.
The SiFive PLIC interrupt controller seems to have all the HW
features to support the fasteoi flow, but the driver seems to be
stuck in a distant past. Bring it into the 21st century.
Signed-off-by: Marc Zyngier <maz@kernel.org> Tested-by: Palmer Dabbelt <palmer@sifive.com> (QEMU Boot) Tested-by: Darius Rad <darius@bluespec.com> (on 2 HW PLIC implementations) Tested-by: Paul Walmsley <paul.walmsley@sifive.com> (HiFive Unleashed) Reviewed-by: Palmer Dabbelt <palmer@sifive.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/8636gxskmj.wl-maz@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
GFP_NOWAIT allocation can fail anytime - it doesn't wait for memory being
available and it fails if the mempool is exhausted and there is not enough
memory.
If we go down this path:
map_bio -> mg_start -> alloc_migration -> mempool_alloc(GFP_NOWAIT)
we can see that map_bio() doesn't check the return value of mg_start(),
and the bio is leaked.
If we go down this path:
map_bio -> mg_start -> mg_lock_writes -> alloc_prison_cell ->
dm_bio_prison_alloc_cell_v2 -> mempool_alloc(GFP_NOWAIT) ->
mg_lock_writes -> mg_complete
the bio is ended with an error - it is unacceptable because it could
cause filesystem corruption if the machine ran out of memory
temporarily.
Change GFP_NOWAIT to GFP_NOIO, so that the mempool code will properly
wait until memory becomes available. mempool_alloc with GFP_NOIO can't
fail, so remove the code paths that deal with allocation failure.
Users reported a v5.3 performance regression and inability to establish
huge page mappings. A revised version of the ndctl "dax.sh" huge page
unit test identifies commit 23c84eb78375 "dax: Fix missed wakeup with
PMD faults" as the source.
Update get_unlocked_entry() to check for NULL entries before checking
the entry order, otherwise NULL is misinterpreted as a present pte
conflict. The 'order' check needs to happen before the locked check as
an unlocked entry at the wrong order must fallback to lookup the correct
order.
Reported-by: Jeff Smits <jeff.smits@intel.com> Reported-by: Doug Nelson <doug.nelson@intel.com> Cc: <stable@vger.kernel.org> Fixes: 23c84eb78375 ("dax: Fix missed wakeup with PMD faults") Reviewed-by: Jan Kara <jack@suse.cz> Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Link: https://lore.kernel.org/r/157167532455.3945484.11971474077040503994.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Any subsequent call to perf_trace_event_reg() will observe total_ref_count > 0,
causing the perf_trace_buf to be always NULL. This can result in perf_trace_buf
getting accessed from perf_trace_buf_alloc() without being initialized. Acquiring
event_mutex in perf_kprobe_init() before calling perf_trace_event_init() should
fix this race.
The race caused the following bug:
Unable to handle kernel paging request at virtual address 0000003106f2003c
Mem abort info:
ESR = 0x96000045
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000045
CM = 0, WnR = 1
user pgtable: 4k pages, 39-bit VAs, pgdp = ffffffc034b9b000
[0000003106f2003c] pgd=0000000000000000, pud=0000000000000000
Internal error: Oops: 96000045 [#1] PREEMPT SMP
Process syz-executor (pid: 18393, stack limit = 0xffffffc093190000)
pstate: 80400005 (Nzcv daif +PAN -UAO)
pc : __memset+0x20/0x1ac
lr : memset+0x3c/0x50
sp : ffffffc09319fc50
allows CAP_EXCLUSIVE events to be grouped with other events. Since all
of those also happen to be AUX events (which is not the case the other
way around, because arch/s390), this changes the rules for stopping the
output: the AUX event may not be on its PMU's context any more, if it's
grouped with a HW event, in which case it will be on that HW event's
context instead. If that's the case, munmap() of the AUX buffer can't
find and stop the AUX event, potentially leaving the last reference with
the atomic context, which will then end up freeing the AUX buffer. This
will then trip warnings:
Fix this by using the context's PMU context when looking for events
to stop, instead of the event's PMU context.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20191022073940.61814-1-alexander.shishkin@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently the code assumes that if a file info entry belongs
to lists of open file handles of an inode and a tcon then
it has non-zero reference. The recent changes broke that
assumption when putting the last reference of the file info.
There may be a situation when a file is being deleted but
nothing prevents another thread to reference it again
and start using it. This happens because we do not hold
the inode list lock while checking the number of references
of the file info structure. Fix this by doing the proper
locking when doing the check.
Fixes: 487317c99477d ("cifs: add spinlock for the openFileList to cifsInodeInfo") Fixes: cb248819d209d ("cifs: use cifsInodeInfo->open_file_lock while iterating to avoid a panic") Cc: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
cifs_setattr_nounix has two paths which miss free operations
for xid and fullpath.
Use goto cifs_setattr_exit like other paths to fix them.
CC: Stable <stable@vger.kernel.org> Fixes: aa081859b10c ("cifs: flush before set-info if we have writeable handles") Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to MS-CIFS specification MID 0xFFFF should not be used by the
CIFS client, but we actually do. Besides, this has proven to cause races
leading to oops between SendReceive2/cifs_demultiplex_thread. On SMB1,
MID is a 2 byte value easy to reach in CurrentMid which may conflict with
an oplock break notification request coming from server
Signed-off-by: Roberto Bergantinos Corpas <rbergant@redhat.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It appears that the only case where we need to apply the TX2_219_TVM
mitigation is when the core is in SMT mode. So let's condition the
enabling on detecting a CPU whose MPIDR_EL1.Aff0 is non-zero.
Cc: <stable@vger.kernel.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As a PRFM instruction racing against a TTBR update can have undesirable
effects on TX2, NOP-out such PRFM on cores that are affected by
the TX2-219 erratum.
Cc: <stable@vger.kernel.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In order to workaround the TX2-219 erratum, it is necessary to trap
TTBRx_EL1 accesses to EL2. This is done by setting HCR_EL2.TVM on
guest entry, which has the side effect of trapping all the other
VM-related sysregs as well.
To minimize the overhead, a fast path is used so that we don't
have to go all the way back to the main sysreg handling code,
unless the rest of the hypervisor expects to see these accesses.
Cc: <stable@vger.kernel.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ghes_edac models a single logical memory controller, and uses a global
ghes_init variable to ensure only the first ghes_edac_register() will
do anything.
ghes_edac is registered the first time a GHES entry in the HEST is
probed. There may be multiple entries, so subsequent attempts to
register ghes_edac are silently ignored as the work has already been
done.
When a GHES entry is unregistered, it calls ghes_edac_unregister(),
which free()s the memory behind the global variables in ghes_edac.
But there may be multiple GHES entries, the next call to
ghes_edac_unregister() will dereference the free()d memory, and attempt
to free it a second time.
This may also be triggered on a platform with one GHES entry, if the
driver is unbound/re-bound and unbound. The re-bind step will do
nothing because of ghes_init, the second unbind will then do the same
work as the first.
Doing the unregister work on the first call is unsafe, as another
CPU may be processing a notification in ghes_edac_report_mem_error(),
using the memory we are about to free.
ghes_init is already half of the reference counting. We only need
to do the register work for the first call, and the unregister work
for the last. Add the unregister check.
This means we no longer free ghes_edac's memory while there are
GHES entries that may receive a notification.
This was detected by KASAN and DEBUG_TEST_DRIVER_REMOVE.
[ bp: merge into a single patch. ]
Fixes: 0fe5f281f749 ("EDAC, ghes: Model a single, logical memory controller") Reported-by: John Garry <john.garry@huawei.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Mauro Carvalho Chehab <mchehab@kernel.org> Cc: Robert Richter <rrichter@marvell.com> Cc: Tony Luck <tony.luck@intel.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20191014171919.85044-2-james.morse@arm.com Link: https://lkml.kernel.org/r/304df85b-8b56-b77e-1a11-aa23769f2e7c@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Sven noticed that calling ioremap() and iounmap() multiple times leads
to a vmap memory leak:
vmap allocation for size 4198400 failed:
use vmalloc=<size> to increase size
A recent commit removed the NULL pointer check from the clock_getres()
implementation causing a test case to fault.
POSIX requires an explicit NULL pointer check for clock_getres() aside of
the validity check of the clock_id argument for obscure reasons.
Add it back for both 32bit and 64bit.
Note, this is only a partial revert of the offending commit which does not
bring back the broken fallback invocation in the the 32bit compat
implementations of clock_getres() and clock_gettime().
Commit "bpf: Process in-kernel BTF" in linux-next introduced an undefined
__weak symbol, which results in an R_390_GLOB_DAT relocation type. That
is not yet handled by the KASLR relocation code, and the kernel stops with
the message "Unknown relocation type".
Add code to detect and handle R_390_GLOB_DAT relocation types and undefined
symbols.
If a process is interrupted while accessing the crypto device and the
global ap_perms_mutex is contented, release() could return early and
fail to free related resources.
Custom outs*/ins* implementations are long gone from the xtensa port,
remove matching EXPORT_SYMBOLs.
This fixes the following build warnings issued by modpost since commit 15bfc2348d54 ("modpost: check for static EXPORT_SYMBOL* functions"):
WARNING: "insb" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "insw" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "insl" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "outsb" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "outsw" [vmlinux] is a static EXPORT_SYMBOL
WARNING: "outsl" [vmlinux] is a static EXPORT_SYMBOL
Mmap /dev/dax more than once, then read the poison location using
address from one of the mappings. The other mappings due to not having
the page mapped in will cause SIGKILLs delivered to the process.
SIGKILL succeeds over SIGBUS, so user process loses the opportunity to
handle the UE.
Although one may add MAP_POPULATE to mmap(2) to work around the issue,
MAP_POPULATE makes mapping 128GB of pmem several magnitudes slower, so
isn't always an option.
Uninitialized memmaps contain garbage and in the worst case trigger
kernel BUGs, especially with CONFIG_PAGE_POISONING. They should not get
touched.
Let's make sure that we only consider online memory (managed by the
buddy) that has initialized memmaps. ZONE_DEVICE is not applicable.
page_zone() will call page_to_nid(), which will trigger
VM_BUG_ON_PGFLAGS(PagePoisoned(page), page) with CONFIG_PAGE_POISONING
and CONFIG_DEBUG_VM_PGFLAGS when called on uninitialized memmaps. This
can be the case when an offline memory block (e.g., never onlined) is
spanned by a zone.
Note: As explained by Michal in [1], alloc_contig_range() will verify
the range. So it boils down to the wrong access in this function.
Until commit 92d12f9544b7 ("memblock: refactor internal allocation
functions") the maximal address for memblock allocations was forced to
memblock.current_limit only for the allocation functions returning
virtual address. The changes introduced by that commit moved the limit
enforcement into the allocation core and as a result the allocation
functions returning physical address also started to limit allocations
to memblock.current_limit.
Commit 1a61ab8038e72 ("mm: memcontrol: replace zone summing with
lruvec_page_state()") has made lruvec_page_state to use per-cpu counters
instead of calculating it directly from lru_zone_size with an idea that
this would be more effective.
Tim has reported that this is not really the case for their database
benchmark which is showing an opposite results where lruvec_page_state
is taking up a huge chunk of CPU cycles (about 25% of the system time
which is roughly 7% of total cpu cycles) on 5.3 kernels. The workload
is running on a larger machine (96cpus), it has many cgroups (500) and
it is heavily direct reclaim bound.
The likely culprit is the cache traffic the lruvec_page_state_local
generates. Dave Hansen says:
: I was thinking purely of the cache footprint. If it's reading
: pn->lruvec_stat_local->count[idx] is three separate cachelines, so 192
: bytes of cache *96 CPUs = 18k of data, mostly read-only. 1 cgroup would
: be 18k of data for the whole system and the caching would be pretty
: efficient and all 18k would probably survive a tight page fault loop in
: the L1. 500 cgroups would be ~90k of data per CPU thread which doesn't
: fit in the L1 and probably wouldn't survive a tight page fault loop if
: both logical threads were banging on different cgroups.
:
: It's just a theory, but it's why I noted the number of cgroups when I
: initially saw this show up in profiles
Fix the regression by partially reverting the said commit and calculate
the lru size explicitly.
Link: http://lkml.kernel.org/r/20190905071034.16822-1-honglei.wang@oracle.com Fixes: 1a61ab8038e72 ("mm: memcontrol: replace zone summing with lruvec_page_state()") Signed-off-by: Honglei Wang <honglei.wang@oracle.com> Reported-by: Tim Chen <tim.c.chen@linux.intel.com> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Tested-by: Tim Chen <tim.c.chen@linux.intel.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Roman Gushchin <guro@fb.com> Cc: Tejun Heo <tj@kernel.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: <stable@vger.kernel.org> [5.2+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Florian and Dave reported [1] a NULL pointer dereference in
__reset_isolation_pfn(). While the exact cause is unclear, staring at
the code revealed two bugs, which might be related.
One bug is that if zone starts in the middle of pageblock, block_page
might correspond to different pfn than block_pfn, and then the
pfn_valid_within() checks will check different pfn's than those accessed
via struct page. This might result in acessing an unitialized page in
CONFIG_HOLES_IN_ZONE configs.
The other bug is that end_page refers to the first page of next
pageblock and not last page of current pageblock. The online and valid
check is then wrong and with sections, the while (page < end_page) loop
might wander off actual struct page arrays.
The kernel panics on an attempt to dereference the NULL memcg pointer.
When shutdown_cache() is called from the kmem_cache_destroy() context, a
memcg kmem_cache might have empty slab pages in a partial list, which are
still charged to the memory cgroup.
These pages are released by free_partial() at the beginning of
shutdown_cache(): either directly or by scheduling a RCU-delayed work
(if the kmem_cache has the SLAB_TYPESAFE_BY_RCU flag). The latter case
is when the reported panic can happen: memcg_unlink_cache() is called
immediately after shrinking partial lists, without waiting for scheduled
RCU works. It sets the kmem_cache->memcg_params.memcg pointer to NULL,
and the following attempt to dereference it by __free_slab() from the
RCU work context causes the panic.
To fix the issue, let's postpone the release of the memcg pointer to
destroy_memcg_params(). It's called from a separate work context by
slab_caches_to_rcu_destroy_workfn(), which contains a full RCU barrier.
This guarantees that all scheduled page release RCU works will complete
before the memcg pointer will be zeroed.
Big thanks for Karsten for the perfect report containing all necessary
information, his help with the analysis of the problem and testing of the
fix.
Patch series "mm/memory_hotplug: Shrink zones before removing memory",
v6.
This series fixes the access of uninitialized memmaps when shrinking
zones/nodes and when removing memory. Also, it contains all fixes for
crashes that can be triggered when removing certain namespace using
memunmap_pages() - ZONE_DEVICE, reported by Aneesh.
We stop trying to shrink ZONE_DEVICE, as it's buggy, fixing it would be
more involved (we don't have SECTION_IS_ONLINE as an indicator), and
shrinking is only of limited use (set_zone_contiguous() cannot detect
the ZONE_DEVICE as contiguous).
We continue shrinking !ZONE_DEVICE zones, however, I reduced the amount
of code to a minimum. Shrinking is especially necessary to keep
zone->contiguous set where possible, especially, on memory unplug of
DIMMs at zone boundaries.
Zones are now properly shrunk when offlining memory blocks or when
onlining failed. This allows to properly shrink zones on memory unplug
even if the separate memory blocks of a DIMM were onlined to different
zones or re-onlined to a different zone after offlining.
With an altmap, the memmap falling into the reserved altmap space are not
initialized and, therefore, contain a garbage NID and a garbage zone.
Make sure to read the NID/zone from a memmap that was initialized.
This fixes a kernel crash that is observed when destroying a namespace:
kernel BUG at include/linux/mm.h:1107!
cpu 0x1: Vector: 700 (Program Check) at [c000000274087890]
pc: c0000000004b9728: memunmap_pages+0x238/0x340
lr: c0000000004b9724: memunmap_pages+0x234/0x340
...
pid = 3669, comm = ndctl
kernel BUG at include/linux/mm.h:1107!
devm_action_release+0x30/0x50
release_nodes+0x268/0x2d0
device_release_driver_internal+0x174/0x240
unbind_store+0x13c/0x190
drv_attr_store+0x44/0x60
sysfs_kf_write+0x70/0xa0
kernfs_fop_write+0x1ac/0x290
__vfs_write+0x3c/0x70
vfs_write+0xe4/0x200
ksys_write+0x7c/0x140
system_call+0x5c/0x68
The "page_zone(pfn_to_page(pfn)" was introduced by 69324b8f4833 ("mm,
devm_memremap_pages: add MEMORY_DEVICE_PRIVATE support"), however, I
think we will never have driver reserved memory with
MEMORY_DEVICE_PRIVATE (no altmap AFAIKS).
[david@redhat.com: minimze code changes, rephrase description] Link: http://lkml.kernel.org/r/20191006085646.5768-2-david@redhat.com Fixes: 2c2a5af6fed2 ("mm, memory_hotplug: add nid parameter to arch_remove_memory") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: David Hildenbrand <david@redhat.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Damian Tometzki <damian.tometzki@gmail.com> Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Halil Pasic <pasic@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jun Yao <yaojun8558363@gmail.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Michal Hocko <mhocko@suse.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Pankaj Gupta <pagupta@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Pavel Tatashin <pavel.tatashin@microsoft.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qian Cai <cai@lca.pw> Cc: Rich Felker <dalias@libc.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Steve Capper <steve.capper@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Wei Yang <richardw.yang@linux.intel.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Yu Zhao <yuzhao@google.com> Cc: <stable@vger.kernel.org> [5.0+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Uninitialized memmaps contain garbage and in the worst case trigger
kernel BUGs, especially with CONFIG_PAGE_POISONING. They should not get
touched.
For example, when not onlining a memory block that is spanned by a zone
and reading /proc/pagetypeinfo with CONFIG_DEBUG_VM_PGFLAGS and
CONFIG_PAGE_POISONING, we can trigger a kernel BUG:
Please note that this change does not affect ZONE_DEVICE, because
pagetypeinfo_showmixedcount_print() is called from
mm/vmstat.c:pagetypeinfo_showmixedcount() only for populated zones, and
ZONE_DEVICE is never populated (zone->present_pages always 0).
[david@redhat.com: move check to outer loop, add comment, rephrase description] Link: http://lkml.kernel.org/r/20191011140638.8160-1-david@redhat.com Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") # visible after d0dc12e86b319 Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: David Hildenbrand <david@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Miles Chen <miles.chen@mediatek.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Qian Cai <cai@lca.pw> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> [4.13+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A long time ago we fixed a similar deadlock in show_slab_objects() [1].
However, it is apparently due to the commits like 01fb58bcba63 ("slab:
remove synchronous synchronize_sched() from memcg cache deactivation
path") and 03afc0e25f7f ("slab: get_online_mems for
kmem_cache_{create,destroy,shrink}"), this kind of deadlock is back by
just reading files in /sys/kernel/slab which will generate a lockdep
splat below.
Since the "mem_hotplug_lock" here is only to obtain a stable online node
mask while racing with NUMA node hotplug, in the worst case, the results
may me miscalculated while doing NUMA node hotplug, but they shall be
corrected by later reads of the same files.
WARNING: possible circular locking dependency detected
------------------------------------------------------
cat/5224 is trying to acquire lock: ffff900012ac3120 (mem_hotplug_lock.rw_sem){++++}, at:
show_slab_objects+0x94/0x3a8
but task is already holding lock: b8ff009693eee398 (kn->count#45){++++}, at: kernfs_seq_start+0x44/0xf0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
I think it is important to mention that this doesn't expose the
show_slab_objects to use-after-free. There is only a single path that
might really race here and that is the slab hotplug notifier callback
__kmem_cache_shrink (via slab_mem_going_offline_callback) but that path
doesn't really destroy kmem_cache_node data structures.
According to the App note[1] detailing the tuning algorithm, for
temperatures < -20C, the initial tuning value should be min(largest value
in LPW - 24, ceil(13/16 ratio of LPW)). The largest value in LPW is
(max_window + 4 * (max_len - 1)) and not (max_window + 4 * max_len) itself.
Fix this implementation.
Since ceeeb99cd821 we no longer abuse the DMA_CTRL_ACK flag for custom
driver use and introduced the MXS_DMA_CTRL_WAIT4END instead. We have not
changed all users to this flag though. This patch fixes it for the
mxs-mmc driver.
We currently use the ring values directly, but that can lead to issues
if the application is malicious and changes these values on our behalf.
Created in-kernel cached versions of them, and just overwrite the user
side when we update them. This is similar to how we treat the sq/cq
ring tail/head updates.
Reported-by: Pavel Begunkov <asml.silence@gmail.com> Reviewed-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
io_ring_submit() finalises with
1. io_commit_sqring(), which releases sqes to the userspace
2. Then calls to io_queue_link_head(), accessing released head's sqe
io_sq_thread() processes sqes by 8 without considering links. As a
result, links will be randomely subdivided.
The easiest way to fix it is to call io_get_sqring() inside
io_submit_sqes() as do io_ring_submit().
Downsides:
1. This removes optimisation of not grabbing mm_struct for fixed files
2. It submitting all sqes in one go, without finer-grained sheduling
with cq processing.
There are three places where we access uninitialized memmaps, namely:
- /proc/kpagecount
- /proc/kpageflags
- /proc/kpagecgroup
We have initialized memmaps either when the section is online or when the
page was initialized to the ZONE_DEVICE. Uninitialized memmaps contain
garbage and in the worst case trigger kernel BUGs, especially with
CONFIG_PAGE_POISONING.
For example, not onlining a DIMM during boot and calling /proc/kpagecount
with CONFIG_PAGE_POISONING:
For now, let's drop support for ZONE_DEVICE from the three pseudo files
in order to fix this. To distinguish offline memory (with garbage
memmap) from ZONE_DEVICE memory with properly initialized memmaps, we
would have to check get_dev_pagemap() and pfn_zone_device_reserved()
right now. The usage of both (especially, special casing devmem) is
frowned upon and needs to be reworked.
The fundamental issue we have is:
if (pfn_to_online_page(pfn)) {
/* memmap initialized */
} else if (pfn_valid(pfn)) {
/*
* ???
* a) offline memory. memmap garbage.
* b) devmem: memmap initialized to ZONE_DEVICE.
* c) devmem: reserved for driver. memmap garbage.
* (d) devmem: memmap currently initializing - garbage)
*/
}
We'll leave the pfn_zone_device_reserved() check in stable_page_flags()
in place as that function is also used from memory failure. We now no
longer dump information about pages that are not in use anymore -
offline.
Link: http://lkml.kernel.org/r/20191009142435.3975-2-david@redhat.com Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b319] Signed-off-by: David Hildenbrand <david@redhat.com> Reported-by: Qian Cai <cai@lca.pw> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Toshiki Fukasawa <t-fukasawa@vx.jp.nec.com> Cc: Pankaj gupta <pagupta@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Anthony Yznaga <anthony.yznaga@oracle.com> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com> Cc: <stable@vger.kernel.org> [4.13+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Uninitialized memmaps contain garbage and in the worst case trigger kernel
BUGs, especially with CONFIG_PAGE_POISONING. They should not get touched.
Right now, when trying to soft-offline a PFN that resides on a memory
block that was never onlined, one gets a misleading error with
CONFIG_PAGE_POISONING:
But the actual result depends on the garbage in the memmap.
soft_offline_page() can only work with online pages, it returns -EIO in
case of ZONE_DEVICE. Make sure to only forward pages that are online
(iow, managed by the buddy) and, therefore, have an initialized memmap.
Add a check against pfn_to_online_page() and similarly return -EIO.
Link: http://lkml.kernel.org/r/20191010141200.8985-1-david@redhat.com Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b319] Signed-off-by: David Hildenbrand <david@redhat.com> Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: <stable@vger.kernel.org> [4.13+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
user_pages array should always be freed after validation regardless if
user pages are changed after bo is created because with HMM change parse
bo always allocate user pages array to get user pages for userptr bo.
v2: remove unused local variable and amend commit
v3: add back get user pages in gem_userptr_ioctl, to detect application
bug where an userptr VMA is not ananymous memory and reject it.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Tested-by: Joe Barnett <thejoe@gmail.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 5.3 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The first come first served apporoach to handling the VBT
child device AUX ch conflicts has backfired. We have machines
in the wild where the VBT specifies both port A eDP and
port E DP (in that order) with port E being the real one.
So let's try to flip the preference around and let the last
child device win once again.
Cc: stable@vger.kernel.org Cc: Jani Nikula <jani.nikula@intel.com> Tested-by: Masami Ichikawa <masami256@gmail.com> Tested-by: Torsten <freedesktop201910@liggy.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111966 Fixes: 36a0f92020dc ("drm/i915/bios: make child device order the priority order") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191011202030.8829-1-ville.syrjala@linux.intel.com Acked-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 41e35ffb380bde1379e4030bb5b2ac824d5139cf) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Daniel Vetter uncovered a nasty cycle in using the mmu-notifiers to
invalidate userptr objects which also happen to be pulled into GGTT
mmaps. That is when we unbind the userptr object (on mmu invalidation),
we revoke all CPU mmaps, which may then recurse into mmu invalidation.
We looked for ways of breaking the cycle, but the revocation on
invalidation is required and cannot be avoided. The only solution we
could see was to not allow such GGTT bindings of userptr objects in the
first place. In practice, no one really wants to use a GGTT mmapping of
a CPU pointer...
Just before Daniel's explosive lockdep patches land in v5.4-rc1, we got
a genuine blip from CI:
<4>[ 246.793958] ======================================================
<4>[ 246.793972] WARNING: possible circular locking dependency detected
<4>[ 246.793989] 5.3.0-gbd6c56f50d15-drmtip_372+ #1 Tainted: G U
<4>[ 246.794003] ------------------------------------------------------
<4>[ 246.794017] kswapd0/145 is trying to acquire lock:
<4>[ 246.794030] 000000003f565be6 (&dev->struct_mutex/1){+.+.}, at: userptr_mn_invalidate_range_start+0x18f/0x220 [i915]
<4>[ 246.794250]
but task is already holding lock:
<4>[ 246.794263] 000000001799cef9 (&anon_vma->rwsem){++++}, at: page_lock_anon_vma_read+0xe6/0x2a0
<4>[ 246.794291]
which lock already depends on the new lock.
Bail from the pci_driver probe function instead of from the drm_driver
load function.
This avoid /dev/dri/card0 temporarily getting registered and then
unregistered again, sending unwanted add / remove udev events to
userspace.
Specifically this avoids triggering the (userspace) bug fixed by this
plymouth merge-request:
https://gitlab.freedesktop.org/plymouth/plymouth/merge_requests/59
Note that despite that being a userspace bug, not sending unnecessary
udev events is a good idea in general.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1490490 Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Panfrost uses multiple schedulers (one for each slot, so 2 in reality),
and on a timeout has to stop all the schedulers to safely perform a
reset. However more than one scheduler can trigger a timeout at the same
time. This race condition results in jobs being freed while they are
still in use.
When stopping other slots use cancel_delayed_work_sync() to ensure that
any timeout started for that slot has completed. Also use
mutex_trylock() to obtain reset_lock. This means that only one thread
attempts the reset, the other threads will simply complete without doing
anything (the first thread will wait for this in the call to
cancel_delayed_work_sync()).
While we're here and since the function is already dependent on
sched_job not being NULL, let's remove the unnecessary checks.
Fixes: aa20236784ab ("drm/panfrost: Prevent concurrent resets") Tested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Steven Price <steven.price@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191009094456.9704-1-steven.price@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 4daa4fba3a38 ("gpu: drm: ttm: Adding new return type vm_fault_t")
broke TTM prefaulting. Since vmf_insert_mixed() typically always returns
VM_FAULT_NOPAGE, prefaulting stops after the second PTE.
Restore (almost) the original behaviour. Unfortunately we can no longer
with the new vm_fault_t return type determine whether a prefaulting
PTE insertion hit an already populated PTE, and terminate the insertion
loop. Instead we continue with the pre-determined number of prefaults.
Fixes: 4daa4fba3a38 ("gpu: drm: ttm: Adding new return type vm_fault_t") Cc: Souptick Joarder <jrdr.linux@gmail.com> Cc: Christian König <christian.koenig@amd.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Christian König <christian.koenig@amd.com> Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/330387/ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Although this shouldn't occur in practice, it's a good idea to bounds
check the length field of the SSID element prior to using it for things
like allocations or memcpy operations.
Cc: <stable@vger.kernel.org> Cc: Kees Cook <keescook@chromium.org> Reported-by: Nicolas Waisman <nico@semmle.com> Signed-off-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20191004095132.15777-1-will@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There were a bunch of devices with qu and jf that were loading the
configuration with pu and jf, which is wrong. Fix them all
accordingly. Additionally, remove 0x1010 and 0x1210 subsytem IDs from
the list, since they are obviously wrong, and 0x0044 and 0x0244, which
were duplicate.
Unlike other format-related DAI parameters, rdai->bit_clk_inv flag
is not properly re-initialized when setting format for new stream
processing. The inversion, if requested, is then applied not to default,
but to a previous value, which leads to SCKP bit in SSICR register being
set incorrectly.
Fix this by re-setting the flag to its initial value, determined by format.
Fixes: 1a7889ca8aba3 ("ASoC: rsnd: fixup SND_SOC_DAIFMT_xB_xF behavior") Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com> Cc: Jiada Wang <jiada_wang@mentor.com> Cc: Timo Wischer <twischer@de.adit-jv.com> Cc: stable@vger.kernel.org # v3.17+ Signed-off-by: Junya Monden <jmonden@jp.adit-jv.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20191016124255.7442-1-erosca@de.adit-jv.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
For Sitronix st1633 multi-touch controller driver the coordinates reported
for multiple fingers were wrong, as it was always taking LSB of coordinates
from the first contact data.
Signed-off-by: Dixit Parmar <dixitparmar19@gmail.com> Reviewed-by: Martin Kepplinger <martink@posteo.de> Cc: stable@vger.kernel.org Fixes: 351e0592bfea ("Input: st1232 - add support for st1633")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204561 Link: https://lore.kernel.org/r/1566209314-21767-1-git-send-email-dixitparmar19@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
rmi_process_interrupt_requests() calls handle_nested_irq() for
each interrupt status bit it finds. If the irq domain mapping for
this bit had not yet been set up, then it ends up calling
handle_nested_irq(0), which causes a NULL pointer dereference.
There's already code that masks the irq_status bits coming out of the
hardware with current_irq_mask, presumably to avoid this situation.
However current_irq_mask seems to more reflect the actual mask set
in the hardware rather than the IRQs software has set up and registered
for. For example, in rmi_driver_reset_handler(), the current_irq_mask
is initialized based on what is read from the hardware. If the reset
value of this mask enables IRQs that Linux has not set up yet, then
we end up in this situation.
There appears to be a third unused bitmask that used to serve this
purpose, fn_irq_bits. Use that bitmask instead of current_irq_mask
to avoid calling handle_nested_irq() on IRQs that have not yet been
set up.
Signed-off-by: Evan Green <evgreen@chromium.org> Reviewed-by: Andrew Duggan <aduggan@synaptics.com> Link: https://lore.kernel.org/r/20191008223657.163366-1-evgreen@chromium.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since commit f889beaaab1c ("Input: da9063 - report KEY_POWER instead of
KEY_SLEEP during power key-press") KEY_SLEEP isn't supported anymore. This
caused input device to not generate any events if "dlg,disable-key-power"
is set.
Fix this by unconditionally setting KEY_POWER capability, and not
declaring KEY_SLEEP.
Fixes: f889beaaab1c ("Input: da9063 - report KEY_POWER instead of KEY_SLEEP during power key-press") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Clearing ch->device in ch_release() is wrong because that pointer must
remain valid until ch_remove() is called. This patch fixes the following
crash the second time a ch device is opened:
We have a test case like block/001 in blktests, which will create a scsi
device by loading scsi_debug module and then try to delete the device by
sysfs interface. At the same time, it may remove the scsi_debug module.
And getting a invalid paging request BUG_ON as following:
During deleting scsi target, the scsi_debug module have been removed. Then,
sdebug_driver_template belonged to the module cannot be accessd, resulting
in scsi_proc_hostdir_rm() BUG_ON.
To fix the bug, we add scsi_device_get() in sdev_store_delete() to try to
increase refcount of module, avoiding the module been removed.
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191015130556.18061-1-yuyufen@huawei.com Signed-off-by: Yufen Yu <yuyufen@huawei.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a non-passthrough command is terminated with CHECK CONDITION, request
sense is executed by hijacking the command descriptor. Since
scsi_eh_prep_cmnd() and scsi_eh_restore_cmnd() do not save/restore the
original command resid, the value returned on failure of the original
command is lost and replaced with the value set by the execution of the
request sense command. This value may in many instances be unaligned to the
device sector size, causing sd_done() to print a warning message about the
incorrect unaligned resid before the command is retried.
Fix this problem by saving the original command residual in struct
scsi_eh_save using scsi_eh_prep_cmnd() and restoring it in
scsi_eh_restore_cmnd(). In addition, to make sure that the request sense
command is executed with a correctly initialized command structure, also
reset the residual to 0 in scsi_eh_prep_cmnd() after saving the original
command value in struct scsi_eh_save.
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191001074839.1994-1-damien.lemoal@wdc.com Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
I've got a report about a UAS drive enclosure reporting back Sense: Logical
unit access not authorized if the drive it holds is password protected.
While the drive is obviously unusable in that state as a mass storage
device, it still exists as a sd device and when the system is asked to
perform a suspend of the drive, it will be sent a SYNCHRONIZE CACHE. If
that fails due to password protection, the error must be ignored.
Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20190903101840.16483-1-oneukum@suse.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
On excessive bit errors for the FCP channel ingress fibre path, the channel
notifies us. Previously, we only emitted a kernel message and a trace
record. Since performance can become suboptimal with I/O timeouts due to
bit errors, we now stop using an FCP device by default on channel
notification so multipath on top can timely failover to other paths. A new
module parameter zfcp.ber_stop can be used to get zfcp old behavior.
User explanation of new kernel message:
* Description:
* The FCP channel reported that its bit error threshold has been exceeded.
* These errors might result from a problem with the physical components
* of the local fibre link into the FCP channel.
* The problem might be damage or malfunction of the cable or
* cable connection between the FCP channel and
* the adjacent fabric switch port or the point-to-point peer.
* Find details about the errors in the HBA trace for the FCP device.
* The zfcp device driver closed down the FCP device
* to limit the performance impact from possible I/O command timeouts.
* User action:
* Check for problems on the local fibre link, ensure that fibre optics are
* clean and functional, and all cables are properly plugged.
* After the repair action, you can manually recover the FCP device by
* writing "0" into its "failed" sysfs attribute.
* If recovery through sysfs is not possible, set the CHPID of the device
* offline and back online on the service element.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: <stable@vger.kernel.org> #2.6.30+ Link: https://lore.kernel.org/r/20191001104949.42810-1-maier@linux.ibm.com Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently the exit return path when sme->key_idx >= NUM_WEPKEYS is via
label 'exit' and this checks if result is non-zero, however result has
not been initialized and contains garbage. Fix this by replacing the
goto with a return with the error code.
Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 0ca6d8e74489 ("Staging: wlan-ng: replace switch-case statements with macro") Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191014110201.9874-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
build_restore_pagemask() will restore the value of register $1/$at when
its restore_scratch argument is non-zero, and aims to do so by filling a
branch delay slot. Commit 0b24cae4d535 ("MIPS: Add missing EHB in mtc0
-> mfc0 sequence.") added an EHB instruction (Execution Hazard Barrier)
prior to restoring $1 from a KScratch register, in order to resolve a
hazard that can result in stale values of the KScratch register being
observed. In particular, P-class CPUs from MIPS with out of order
execution pipelines such as the P5600 & P6600 are affected.
Unfortunately this EHB instruction was inserted in the branch delay slot
causing the MFC0 instruction which performs the restoration to no longer
execute along with the branch. The result is that the $1 register isn't
actually restored, ie. the TLB refill exception handler clobbers it -
which is exactly the problem the EHB is meant to avoid for the P-class
CPUs.
Similarly build_get_pgd_vmalloc() will restore the value of $1/$at when
its mode argument equals refill_scratch, and suffers from the same
problem.
Fix this by in both cases moving the EHB earlier in the emitted code.
There's no reason it needs to immediately precede the MFC0 - it simply
needs to be between the MTC0 & MFC0.
This bug only affects Cavium Octeon systems which use
build_fast_tlb_refill_handler().
binder_mmap() tries to prevent the creation of overly big binder mappings
by silently truncating the size of the VMA to 4MiB. However, this violates
the API contract of mmap(). If userspace attempts to create a large binder
VMA, and later attempts to unmap that VMA, it will call munmap() on a range
beyond the end of the VMA, which may have been allocated to another VMA in
the meantime. This can lead to userspace memory corruption.
The following sequence of calls leads to a segfault without this commit:
Fix broken read implementation, which could be used to trigger slab info
leaks.
The driver failed to check if the custom ring buffer was still empty
when waking up after having waited for more data. This would happen on
every interrupt-in completion, even if no data had been added to the
ring buffer (e.g. on disconnect events).
Due to missing sanity checks and uninitialised (kmalloced) ring-buffer
entries, this meant that huge slab info leaks could easily be triggered.
Note that the empty-buffer check after wakeup is enough to fix the info
leak on disconnect, but let's clear the buffer on allocation and add a
sanity check to read() to prevent further leaks.
A recent commit addressing a runtime PM use-count regression, introduced
a use-after-free by not making sure we held a reference to the struct
usb_interface for the lifetime of the driver data.
If disconnect() races with release() after a process has been
interrupted, release() could end up returning early and the driver would
fail to free its driver data.
Fix races between closing a port and opening or closing another port on
the same device which could lead to a failure to start or stop the
shared interrupt URB. The latter could potentially cause a
use-after-free or worse in the completion handler on driver unbind.
It seems that the right variable to use in this case is *i*, instead of
*n*, otherwise there is an undefined behavior when right shifiting by more
than 31 bits when multiplying n by 8; notice that *n* can take values
equal or greater than 4 (4, 8, 16, ...).
Also, notice that under the current conditions (bl = 3), we are skiping
the handling of bytes 3, 7, 31... So, fix this by updating this logic
and limit *bl* up to 4 instead of up to 3.
This fix is based on function udc_stuff_fifo().
Addresses-Coverity-ID: 1454834 ("Bad bit shift operation") Fixes: 24a28e428351 ("USB: gadget driver for LPC32xx") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Link: https://lore.kernel.org/r/20191014191830.GA10721@embeddedor Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Przemysław Kopa reports that since commit b516ea586d71 ("PCI: Enable
NVIDIA HDA controllers"), the discrete GPU Nvidia GeForce GT 540M on his
2011 Samsung laptop refuses to runtime suspend, resulting in a power
regression and excessive heat.
Rivera Valdez witnesses the same issue with a GeForce GT 525M (GF108M)
of the same era, as does another Arch Linux user named "R0AR" with a
more recent GeForce GTX 1050 Ti (GP107M).
The commit exposes the discrete GPU's HDA controller and all four codecs
on the controller do not set the CLKSTOP and EPSS bits in the Supported
Power States Response. They also do not set the PS-ClkStopOk bit in the
Get Power State Response. hda_codec_runtime_suspend() therefore does
not call snd_hdac_codec_link_down(), which prevents each codec and the
PCI device from runtime suspending.
The same issue is present on some AMD discrete GPUs and we addressed it
by forcing runtime PM despite the bits not being set, see commit 57cb54e53bdd ("ALSA: hda - Force to link down at runtime suspend on
ATI/AMD HDMI").
On Asus MJ401TA (with Realtek ALC256), the headset mic is connected to
pin 0x19, with default configuration value 0x411111f0 (indicating no
physical connection).
Enable this by quirking the pin. Mic jack detection was also tested and
found to be working.
This enables use of the headset mic on this product.
If disconnect() races with release() after a process has been
interrupted, release() could end up returning early and the driver would
fail to free its driver data.
We currently assume that submissions from the sqthread are successful,
and if IO polling is enabled, we use that value for knowing how many
completions to look for. But if we overflowed the CQ ring or some
requests simply got errored and already completed, they won't be
available for polling.
For the case of IO polling and SQTHREAD usage, look at the pending
poll list. If it ever hits empty then we know that we don't have
anymore pollable requests inflight. For that case, simply reset
the inflight count to zero.
Reported-by: Pavel Begunkov <asml.silence@gmail.com> Reviewed-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We need to extend the rcu_read_lock() section in rxrpc_error_report()
and use rcu_dereference_sk_user_data() instead of plain access
to sk->sk_user_data to make sure all rules are respected.
The compiler wont reload sk->sk_user_data at will, and RCU rules
prevent memory beeing freed too soon.
Fixes: f0308fb07080 ("rxrpc: Fix possible NULL pointer access in ICMP handling") Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
NET_VENDOR_BROADCOM is intended to control a kconfig menu only.
It should not have anything to do with code generation.
As such, it should not select DIMLIB for all drivers under
NET_VENDOR_BROADCOM. Instead each driver that needs DIMLIB should
select it (being the symbols SYSTEMPORT, BNXT, and BCMGENET).
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907021810220.13058@ramsan.of.borg/ Fixes: 4f75da3666c0 ("linux/dim: Move implementation to .c files") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Uwe Kleine-König <uwe@kleine-koenig.org> Cc: Tal Gilboa <talgi@mellanox.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: netdev@vger.kernel.org Cc: linux-rdma@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Doug Ledford <dledford@redhat.com> Cc: Jason Gunthorpe <jgg@mellanox.com> Cc: Leon Romanovsky <leonro@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Cc: Sagi Grimberg <sagi@grimberg.me> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress protocol ip matchall \
> action mpls push protocol mpls_uc label 0x355aa bos 1
causes corruption of all IP packets transmitted by eth0. On TC egress, we
can't rely on the value of skb->mac_len, because it's 0 and a MPLS 'push'
operation will result in an overwrite of the first 4 octets in the packet
L2 header (e.g. the Destination Address if eth0 is an Ethernet); the same
error pattern is present also in the MPLS 'pop' operation. Fix this error
in act_mpls data plane, computing 'mac_len' as the difference between the
network header and the mac header (when not at TC ingress), and use it in
MPLS 'push'/'pop' core functions.
v2: unbreak 'make htmldocs' because of missing documentation of 'mac_len'
in skb_mpls_pop(), reported by kbuild test robot
CC: Lorenzo Bianconi <lorenzo@kernel.org> Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC") Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: John Hurley <john.hurley@netronome.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress matchall action mpls pop
implicitly makes the kernel drop all packets transmitted by eth0, if they
don't have a MPLS header. This behavior is uncommon: other encapsulations
(like VLAN) just let the packet pass unmodified. Since the result of MPLS
'pop' operation would be the same regardless of the presence / absence of
MPLS header(s) in the original packet, we can let skb_mpls_pop() return 0
when dealing with non-MPLS packets.
For the OVS use-case, this is acceptable because __ovs_nla_copy_actions()
already ensures that MPLS 'pop' operation only occurs with packets having
an MPLS Ethernet type (and there are no other callers in current code, so
the semantic change should be ok).
v2: better documentation of use-cases for skb_mpls_pop(), thanks to Simon
Horman
Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC") Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: John Hurley <john.hurley@netronome.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: George McCollister <george.mccollister@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: David S. Miller <davem@davemloft.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: George McCollister <george.mccollister@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: Woojung Huh <woojung.huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
macvlan and multicast handling is now mixed up.
The explicit issue is that macvlan interface gets broken (no traffic)
after clearing MULTICAST flag on the real interface.
We now do separate logic and consider both ALLMULTI and MULTICAST
flags on the device.
Fixes: 11ba961c9161 ("net: aquantia: Fix IFF_ALLMULTI flag functionality") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Individual descriptors on LRO TCP session should be checked
for CRC errors. It was discovered that HW recalculates
L4 checksums on LRO session and does not break it up on bad L4
csum.
Thus, driver should aggregate HW LRO L4 statuses from all individual
buffers of LRO session and drop packet if one of the buffers has bad
L4 checksum.
Fixes: f38f1ee8aeb2 ("net: aquantia: check rx csum for all packets in LRO session") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Chip temperature is a two byte word, colocated internally with cable
length data. We do all readouts from HW memory by dwords, thus
we should clear extra high bytes, otherwise temperature output
gets weird as soon as we attach a cable to the NIC.
Fixes: 8f8940118654 ("net: aquantia: add infrastructure to readout chip temperature") Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It was caused by when sending msgs without binding a port, in the path:
inet_sendmsg() -> inet_send_prepare() -> inet_autobind() ->
.get_port/sctp_get_port(), sp->bind_hash will be set while bp->port is
not. Later when binding another port by sctp_setsockopt_bindx(), a new
bucket will be created as bp->port is not set.
sctp's autobind is supposed to call sctp_autobind() where it does all
things including setting bp->port. Since sctp_autobind() is called in
sctp_sendmsg() if the sk is not yet bound, it should have skipped the
auto bind.
THis patch is to avoid calling inet_autobind() in inet_send_prepare()
by changing sctp_prot .no_autobind with true, also remove the unused
.get_port.
Reported-by: syzbot+d44f7bbebdea49dbc84a@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a application sends many packets with the same txtime, they may
be transmitted out of order (different from the order in which they
were enqueued).
This happens because when inserting elements into the tree, when the
txtime of two packets are the same, the new packet is inserted at the
left side of the tree, causing the reordering. The only effect of this
change should be that packets with the same txtime will be transmitted
in the order they are enqueued.
The application in question (the AVTP GStreamer plugin, still in
development) is sending video traffic, in which each video frame have
a single presentation time, the problem is that when packetizing,
multiple packets end up with the same txtime.
The receiving side was rejecting packets because they were being
received out of order.
Fixes: 25db26a91364 ("net/sched: Introduce the ETF Qdisc") Reported-by: Ederson de Souza <ederson.desouza@intel.com> Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Connor Kuehl <connor.kuehl@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
projects / mirror_ubuntu-eoan-kernel.git / log