pageout() in MM traslates EAGAIN, so calls handle_write_error()
-> mapping_set_error() -> set_bit(AS_EIO, ...).
file_write_and_wait_range() will see EIO error, which is critical
to return value of fsync() followed by atomic_write failure to user.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The FastReg support in ko2iblnd was not unmapping pool items
causing the items to leak. In addition, the mapping code
is not growing the pool like we do with FMR.
This patch makes sure we are unmapping FastReg pool elements
when we are done with them. It also makes sure the pool
will grow when we depleat the pool.
cmid will be destroyed at OFED if kiblnd_cm_callback return error.
if error happen before the end of kiblnd_connect_peer, it will touch
destroyed cmid and fail as
(o2iblnd_cb.c:1315:kiblnd_connect_peer())
ASSERTION( cmid->device != ((void *)0) ) failed:
Signed-off-by: Alexander Boyko <alexander.boyko@seagate.com>
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-10015 Reviewed-by: Alexey Lyashkov <c17817@cray.com> Reviewed-by: Doug Oucharek <dougso@me.com> Reviewed-by: John L. Hammond <john.hammond@intel.com> Signed-off-by: Doug Oucharek <dougso@me.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Similar to what we do when we remove a PCI function, set the
QEDF_UNLOADING flag to prevent any requests from being queued while a
vport is being deleted. This prevents any requests from getting stuck
in limbo when the vport is unloaded or deleted.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If we had more than 32 megaraid cards then it would cause memory
corruption. That's not likely, of course, but it's handy to enforce it
and make the static checker happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In tw_chrdev_ioctl(), the length of the data buffer is firstly copied
from the userspace pointer 'argp' and saved to the kernel object
'data_buffer_length'. Then a security check is performed on it to make
sure that the length is not more than 'TW_MAX_IOCTL_SECTORS *
512'. Otherwise, an error code -EINVAL is returned. If the security
check is passed, the entire ioctl command is copied again from the
'argp' pointer and saved to the kernel object 'tw_ioctl'. Then, various
operations are performed on 'tw_ioctl' according to the 'cmd'. Given
that the 'argp' pointer resides in userspace, a malicious userspace
process can race to change the buffer length between the two
copies. This way, the user can bypass the security check and inject
invalid data buffer length. This can cause potential security issues in
the following execution.
This patch checks for capable(CAP_SYS_ADMIN) in tw_chrdev_open() to
avoid the above issues.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In twa_chrdev_ioctl(), the ioctl driver command is firstly copied from
the userspace pointer 'argp' and saved to the kernel object
'driver_command'. Then a security check is performed on the data buffer
size indicated by 'driver_command', which is
'driver_command.buffer_length'. If the security check is passed, the
entire ioctl command is copied again from the 'argp' pointer and saved
to the kernel object 'tw_ioctl'. Then, various operations are performed
on 'tw_ioctl' according to the 'cmd'. Given that the 'argp' pointer
resides in userspace, a malicious userspace process can race to change
the buffer size between the two copies. This way, the user can bypass
the security check and inject invalid data buffer size. This can cause
potential security issues in the following execution.
This patch checks for capable(CAP_SYS_ADMIN) in twa_chrdev_open()t o
avoid the above issues.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Only non-NPAR PFs need to actively check and manage unsupported link
speeds. NPAR functions and VFs do not control the link speed and
should skip the unsupported speed detection logic, to avoid warning
messages from firmware rejecting the unsupported firmware calls.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The s390 CPU measurement facility sampling mode supports basic entries
and diagnostic entries. Each entry has a valid bit to indicate the
status of the entry as valid or invalid.
This bit is bit 31 in the diagnostic entry, but the bit mask definition
refers to bit 30.
Fix this by making the reserved field one bit larger.
Fixes: 7e75fc3ff4cf ("s390/cpum_sf: Add raw data sampling to support the diagnostic-sampling function") Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The CPU Measurement sampling facility creates a trailer entry for each
Sample-Data-Block of stored samples. The trailer entry contains the sizes
(in bytes) of the stored sampling types:
- basic-sampling data entry size
- diagnostic-sampling data entry size
Both sizes are 2 bytes long.
This patch changes the trailer entry definition to reflect this.
Fixes: fcc77f507333 ("s390/cpum_sf: Atomically reset trailer entry fields of sample-data-blocks") Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.
The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.
However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.
Signed-off-by: Sean Lanigan <sean@lano.id.au> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Per ONFI specification (Rev. 4.0), if the CRC of the first parameter page
read is not valid, the host should read redundant parameter page copies.
Fix FSL NAND driver to read the two redundant copies which are mandatory
in the specification.
Signed-off-by: Jane Wan <Jane.Wan@nokia.com> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This issue was reported by a user who downloaded a corrupt saa7164
firmware, then went looking for a valid xc5000 firmware to fix the
error displayed...but the device in question has no xc5000, thus after
much effort, the wild goose chase eventually led to a support call.
The xc5000 has nothing to do with saa7164 (as far as I can tell),
so replace the string with saa7164 as well as give a meaningful
hint on the firmware mismatch.
Signed-off-by: Brad Love <brad@nextdimension.cc> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The Point of View mobii wintab p800w Bay Trail tablet comes with a Crystal
Cove PMIC, yet uses the LPSS PWM for backlight control, rather then the
Crystal Cove's PWM, so we need to call pwm_add_table() to add a
pwm_backlight mapping for the LPSS pwm despite there being an INT33FD
ACPI device present.
On all Bay Trail devices the _HRV object of the INT33FD ACPI device
will normally return 2, to indicate the Bay Trail variant of the CRC
PMIC is present, except on this tablet where _HRV is 0xffff. I guess this
is a hack to make the windows Crystal Cove PWM driver not bind.
Out of the 44 DSTDs with an INT33FD device in there which I have (from
different model devices) only the pov mobii wintab p800w uses 0xffff for
the HRV.
The byt_pwm_setup code calls acpi_dev_present to check for the presence
of a INT33FD ACPI device which indicates that a CRC PMIC is present and
if the INT33FD ACPI device is present then byt_pwm_setup will not add
a pwm_backlight mapping for the LPSS pwm, so that the CRC PWM will get
used instead.
acpi_dev_present has a hrv parameter, this commit make us pass 2 instead
of -1, so that things still match on normal tablets, but on this special
case with its _HRV of 0xffff, the check will now fail so that the
pwm_backlight mapping for the LPSS pwm gets added fixing backlight
brightness control on this device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For failed commands with valid sense data (e.g. NCQ commands),
scsi_check_sense() is used in ata_analyze_tf() to determine if the
command can be retried. In such case, rely on this decision and ignore
the command error mask based decision done in ata_worth_retry().
This fixes useless retries of commands such as unaligned writes on zoned
disks (TYPE_ZAC).
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We are not releasing the link GPIO descriptor with gpiod_put() which results in
subsequent probing to get -EBUSY when calling fwnode_get_named_gpiod(). Fix this
by doing the release in phylink_destroy().
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Inclusion of include/dma-iommu.h when CONFIG_IOMMU_DMA is not selected
results in the following splat:
In file included from drivers/irqchip/irq-gic-v3-mbi.c:20:0:
./include/linux/dma-iommu.h:95:69: error: unknown type name ‘dma_addr_t’
static inline int iommu_get_msi_cookie(struct iommu_domain *domain, dma_addr_t base)
^~~~~~~~~~
./include/linux/dma-iommu.h:108:74: warning: ‘struct list_head’ declared inside parameter list will not be visible outside of this definition or declaration
static inline void iommu_dma_get_resv_regions(struct device *dev, struct list_head *list)
^~~~~~~~~
scripts/Makefile.build:312: recipe for target 'drivers/irqchip/irq-gic-v3-mbi.o' failed
Fix it by including linux/types.h.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Rob Herring <robh@kernel.org> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lkml.kernel.org/r/20180508121438.11301-5-marc.zyngier@arm.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Unlike normal serials, in pty layer, there is no guarantee that multiple
threads don't insert input characters at the same time. If it is happened,
tty_insert_flip_string_fixed_flag can be executed concurrently. This can
lead slab out-of-bounds write in tty_insert_flip_string_fixed_flag.
Call sequences are as follows.
CPU0 CPU1
n_tty_ioctl_helper n_tty_ioctl_helper
__start_tty tty_send_xchar
tty_wakeup pty_write
n_hdlc_tty_wakeup tty_insert_flip_string
n_hdlc_send_frames tty_insert_flip_string_fixed_flag
pty_write
tty_insert_flip_string
tty_insert_flip_string_fixed_flag
To fix the race, acquire port->lock in pty_write() before it inserts input
characters to tty buffer. It prevents multiple threads from inserting
input characters concurrently.
The crash log is as follows:
BUG: KASAN: slab-out-of-bounds in tty_insert_flip_string_fixed_flag+0xb5/
0x130 drivers/tty/tty_buffer.c:316 at addr ffff880114fcc121
Write of size 1792 by task syz-executor0/30017
CPU: 1 PID: 30017 Comm: syz-executor0 Not tainted 4.8.0 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.8.2-0-g33fbe13 by qemu-project.org 04/01/2014 0000000000000000ffff88011638f888ffffffff81694cc3ffff88007d802140 ffff880114fcb300ffff880114fcc300ffff880114fcb300ffff88011638f8b0 ffffffff8130075cffff88011638f940ffff88007d802140ffff880194fcc121
Call Trace:
__dump_stack lib/dump_stack.c:15 [inline]
dump_stack+0xb3/0x110 lib/dump_stack.c:51
kasan_object_err+0x1c/0x70 mm/kasan/report.c:156
print_address_description mm/kasan/report.c:194 [inline]
kasan_report_error+0x1f7/0x4e0 mm/kasan/report.c:283
kasan_report+0x36/0x40 mm/kasan/report.c:303
check_memory_region_inline mm/kasan/kasan.c:292 [inline]
check_memory_region+0x13e/0x1a0 mm/kasan/kasan.c:299
memcpy+0x37/0x50 mm/kasan/kasan.c:335
tty_insert_flip_string_fixed_flag+0xb5/0x130 drivers/tty/tty_buffer.c:316
tty_insert_flip_string include/linux/tty_flip.h:35 [inline]
pty_write+0x7f/0xc0 drivers/tty/pty.c:115
n_hdlc_send_frames+0x1d4/0x3b0 drivers/tty/n_hdlc.c:419
n_hdlc_tty_wakeup+0x73/0xa0 drivers/tty/n_hdlc.c:496
tty_wakeup+0x92/0xb0 drivers/tty/tty_io.c:601
__start_tty.part.26+0x66/0x70 drivers/tty/tty_io.c:1018
__start_tty+0x34/0x40 drivers/tty/tty_io.c:1013
n_tty_ioctl_helper+0x146/0x1e0 drivers/tty/tty_ioctl.c:1138
n_hdlc_tty_ioctl+0xb3/0x2b0 drivers/tty/n_hdlc.c:794
tty_ioctl+0xa85/0x16d0 drivers/tty/tty_io.c:2992
vfs_ioctl fs/ioctl.c:43 [inline]
do_vfs_ioctl+0x13e/0xba0 fs/ioctl.c:679
SYSC_ioctl fs/ioctl.c:694 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:685
entry_SYSCALL_64_fastpath+0x1f/0xbd
In commit bbc4e7d273b5 ("i40e: fix race condition with PTP_TX_IN_PROGRESS
bits") we modified the code which handles Tx timestamps so that we would
clear the progress bit as soon as possible.
A later commit 0bc0706b46cd ("i40e: check for Tx timestamp timeouts during
watchdog") introduced similar code for detecting and handling cleanup of
a blocked Tx timestamp. This code did not use the same pattern for cleaning
up the skb.
Update this code to wait to free the skb until after the bit lock is
free, by first setting the ptp_tx_skb to NULL and clearing the lock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Function nvmem_reg_read can return a non zero value indicating an error.
This returned value must be read and error propagated to
nvmem_cell_prepare_write_buffer. Silence the following gcc warning (W=1):
drivers/nvmem/core.c:1093:9: warning: variable 'rc' set but
not used [-Wunused-but-set-variable]
Since commit 83a86fbb5b56 ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The kbuild test robot reported the following warning:
drivers/edac/altera_edac.c: In function 'ocram_free_mem':
drivers/edac/altera_edac.c:1410:42: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
gen_pool_free((struct gen_pool *)other, (u32)p, size);
^
After adding support for ARM64 architectures, the unsigned long
parameter is 64 bits and causes a build warning on 64-bit configs. Fix
by casting to the correct size (unsigned long) instead of u32.
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-edac <linux-edac@vger.kernel.org> Fixes: c3eea1942a16 ("EDAC, altera: Add Altera L2 cache and OCRAM support") Link: http://lkml.kernel.org/r/1526317441-4996-1-git-send-email-thor.thayer@linux.intel.com Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On many Chromebooks touch devices are multi-sourced; the components are
electrically compatible and one can be freely swapped for another without
changing the OS image or firmware.
To avoid bunch of scary messages when device is not actually present in the
system let's try testing basic communication with it and if there is no
response terminate probe early with -ENXIO.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The interrupt controller inside the Wii's Hollywood chip is connected to
two masters, the "Broadway" PowerPC and the "Starlet" ARM926, each with
their own interrupt status and mask registers.
When booting the Wii with mini[1], interrupts from the SD card
controller (IRQ 7) are handled by the ARM, because mini provides SD
access over IPC. Linux however can't currently use or disable this IPC
service, so both sides try to handle IRQ 7 without coordination.
Let's instead make sure that all interrupts that are unmasked on the PPC
side are masked on the ARM side; this will also make sure that Linux can
properly talk to the SD card controller (and potentially other devices).
If access to a device through IPC is desired in the future, interrupts
from that device should not be handled by Linux directly.
[1]: https://github.com/lewurm/mini
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This fixes an issue introduced by change "allow framebuffer in GART
memory as well" which could lead to a shared buffer ending up
pinned in vram. Use GTT if it is included in the domain, otherwise
return an error.
Signed-off-by: Samuel Li <Samuel.Li@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Current Sound is using simple-audio-card which can't support HDMI.
To use HDMI sound, we need to use audio-graph-card.
But, one note is that r8a7795 has 2 HDMI ports, but r8a7796 has 1.
Because of this mismatch, supporting HDMI on salvator-common is
impossible.
Thus, this patch exchange sound card to audio-graph-card and keep
supporting ak4613 as 1st sound node.
r8a7795/r8a7796 salvator-x{s} need to add HDMI sound individually.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp> Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When waiting for a cacheline to change state in cmpwait, we may immediately
wake-up the first time around the outer loop if the event register was
already set (for example, because of the event stream).
Avoid these spurious wakeups by explicitly clearing the event register
before loading the cacheline and setting the exclusive monitor.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘__ov2680_set_exposure’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:400:10: warning: variable ‘hts’ set but not used [-Wunused-but-set-variable]
u16 vts,hts;
^~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘ov2680_detect’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:1164:5: warning: variable ‘revision’ set but not used [-Wunused-but-set-variable]
u8 revision;
^~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
retire_capture_urb() may print warning messages when the given URB
doesn't align, and this may flood the system log easily.
Put the rate limit to the message for avoiding it.
This fixes klockworks warnings: Pointer 'dev' returned from call to
function 'bus_find_device' at line 179 may be NULL and will be dereferenced
at line 181.
cpsw-phy-sel.c:179: 'dev' is assigned the return value from function 'bus_find_device'.
bus.c:342: 'bus_find_device' explicitly returns a NULL value.
cpsw-phy-sel.c:181: 'dev' is dereferenced by passing argument 1 to function 'dev_get_drvdata'.
device.h:1024: 'dev' is passed to function 'dev_get_drvdata'.
device.h:1026: 'dev' is explicitly dereferenced.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[nsekhar@ti.com: add an error message, fix return path] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The current code decrements the timeout counter i and the end of
each loop i is incremented, so the check for timeout will always
be false and hence the timeout mechanism is just a dead code path.
Potentially, if the RD_READY bit is not set, we could end up in
an infinite loop.
Fix this so the timeout starts from 1000 and decrements to zero,
if at the end of the loop i is zero we have a timeout condition.
Detected by CoverityScan, CID#1324008 ("Logically dead code")
Fixes: ccfc97bdb5ae ("[media] smiapp: Add driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For raid6, when two disk of the array are offline, two spare disks can
be added into the array. Before spare disks recovery completing,
system reboot and mdadm thinks it is ok to restart the degraded
array by md_ioctl(). Since disks in raid6 is not only_parity(),
raid5_run() will abort, when there is no PPL feature or not setting
'start_dirty_degraded' parameter. Therefore, mddev->pers is NULL.
But, mddev->raid_disks has been set and it will not be cleared when
raid5_run abort. md_ioctl() can execute cmd 'HOT_REMOVE_DISK' to
remove a disk by mdadm, which will cause NULL pointer dereference
in remove_and_add_spares() finally.
Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Current handle_read_error() function calls fix_read_error()
only if md device is RW and rdev does not include FailFast flag.
It does not handle a read error from a RW device including
FailFast flag.
I am not sure it is intended. But I found that write IO error
sets rdev faulty. The md module should handle the read IO error and
write IO error equally. So I think read IO error should set rdev faulty.
Signed-off-by: Gioh Kim <gi-oh.kim@profitbricks.com> Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The error messages at sanity checks of memory pages tend to repeat too
many times once when it hits, and without the rate limit, it may flood
and become unreadable. Replace such messages with the *_ratelimited()
variant.
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Otherwise iterating with list_for_each() over the adapter->erp_ready_head
and adapter->erp_running_head lists can lead to an infinite loop. See commit
"zfcp: fix infinite iteration on erp_ready_head list".
The run-time check is only performed for debug kernels which have the kernel
lock validator enabled. Following is an example of the warning that is
reported, if the ERP lock is not held when calling zfcp_dbf_rec_trig():
The device can set the exception event bit in one of the response UPIU,
for example to notify the need for urgent BKOPs operation. In such a
case, the host driver calls ufshcd_exception_event_handler to handle
this notification. When trying to check the exception event status (for
finding the cause for the exception event), the device may be busy with
additional SCSI commands handling and may not respond within the 100ms
timeout.
To prevent that, we need to block SCSI commands during handling of
exception events and allow retransmissions of the query requests, in
case of timeout.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Asutosh Das <asutoshd@codeaurora.org> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Vendor specific setup_clocks ops may depend on clocks managed by ufshcd
driver so if the vendor specific setup_clocks callback is called when
the required clocks are turned off, it results into unclocked register
access.
This change make sure that required clocks are enabled before vendor
specific setup_clocks callback is called.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Improve fscrypt read performance by switching the decryption workqueue
from bound to unbound. With the bound workqueue, when multiple bios
completed on the same CPU, they were decrypted on that same CPU. But
with the unbound queue, they are now decrypted in parallel on any CPU.
Although fscrypt read performance can be tough to measure due to the
many sources of variation, this change is most beneficial when
decryption is slow, e.g. on CPUs without AES instructions. For example,
I timed tarring up encrypted directories on f2fs. On x86 with AES-NI
instructions disabled, the unbound workqueue improved performance by
about 25-35%, using 1 to NUM_CPUs jobs with 4 or 8 CPUs available. But
with AES-NI enabled, performance was unchanged to within ~2%.
I also did the same test on a quad-core ARM CPU using xts-speck128-neon
encryption. There performance was usually about 10% better with the
unbound workqueue, bringing it closer to the unencrypted speed.
The unbound workqueue may be worse in some cases due to worse locality,
but I think it's still the better default. dm-crypt uses an unbound
workqueue by default too, so this change makes fscrypt match.
Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If pm_runtime_get_sync() fails we should call pm_runtime_put_noidle().
This is probably not a critical fix as we should only hit this when
things are broken elsewhere.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The ARM CCN PMU driver uses dev_warn() to complain about parameters in
the user-provided perf_event_attr. This means that under normal
operation (e.g. a single invocation of the perf tool), a number of
messages warnings may be logged to dmesg.
Tools may issue multiple syscalls to probe for feature support, and
multiple applications (from multiple users) can attempt to open events
simultaneously, so this is not very helpful, even if a user happens to
have access to dmesg. Worse, this can push important information out of
the dmesg ring buffer, and can significantly slow down syscall fuzzers,
vastly increasing the time it takes to find critical bugs.
Demote the dev_warn() instances to dev_dbg(), as is the case for all
other PMU drivers under drivers/perf/. Users who wish to debug PMU event
initialisation can enable dynamic debug to receive these messages.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Correct snr/nr/rssi data index to avoid possible buffer underflow.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add support for the four-port variant of the Qualcomm QCA833x switch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently we request control of native PCIe hotplug unconditionally.
Native PCIe hotplug events are handled by the pciehp driver, and if it is
not enabled those events will be lost.
Request control of native PCIe hotplug only if the pciehp driver is
enabled, so we will actually handle native PCIe hotplug events.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For multi-function programs, loading the address of a callee
function to a register requires emitting instructions whose
count varies from one to five depending on the nature of the
address.
Since we come to know of the callee's address only before the
extra pass, the number of instructions required to load this
address may vary from what was previously generated. This can
make the JITed image grow or shrink.
To avoid this, we should generate a constant five-instruction
when loading function addresses by padding the optimized load
sequence with NOPs.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
According to section 59.2.4 MSIOF Receive Mode Register 1 (SIRMDR1) in
the R-Car Gen3 datasheet Rev.1.00, the value of the SIRMDR1.SYNCAC bit
must match the value of the SITMDR1.SYNCAC bit. However,
sh_msiof_spi_setup() changes only the latter.
Fix this by updating the SIRMDR1 register like the SITMDR1 register,
taking into account register bits that exist in SITMDR1 only.
Reported-by: Renesas BSP team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Fixes: 7ff0b53c4051145d ("spi: sh-msiof: Avoid writing to registers from spi_master.setup()") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
__printf is useful to verify format and arguments. Fix arg mismatch
reported by gcc, remove the following warnings (with W=1):
arch/powerpc/kernel/prom_init.c:1467:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1471:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1504:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1505:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1506:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1507:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1508:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1509:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1975:39: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’
arch/powerpc/kernel/prom_init.c:1986:27: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
The patch also include arg mismatch fix for case with #define DEBUG_PROM
(warning not listed here).
This patch fix also the following warnings revealed by checkpatch:
WARNING: Prefer using '"%s...", __func__' to using 'alloc_up', this function's name, in a string
#101: FILE: arch/powerpc/kernel/prom_init.c:1235:
+ prom_debug("alloc_up(%lx, %lx)\n", size, align);
and
WARNING: Prefer using '"%s...", __func__' to using 'alloc_down', this function's name, in a string
#138: FILE: arch/powerpc/kernel/prom_init.c:1278:
+ prom_debug("alloc_down(%lx, %lx, %s)\n", size, align,
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/time.c:41:13: error: no previous prototype for ‘chrp_time_init’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:66:5: error: no previous prototype for ‘chrp_cmos_clock_read’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:74:6: error: no previous prototype for ‘chrp_cmos_clock_write’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:86:5: error: no previous prototype for ‘chrp_set_rtc_time’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:130:6: error: no previous prototype for ‘chrp_get_rtc_time’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The nvme timeout handling doesn't do anything if the pci channel is
offline, which is the case when recovering from PCI error event, so it
was a bad idea to sync the controller reset in this state. This patch
flushes the reset work in the error_resume callback instead when the
channel is back to online. This keeps AER handling serialized and
can recover from timeouts.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199757 Fixes: cc1d5e749a2e ("nvme/pci: Sync controller reset for AER slot_reset") Reported-by: Alex Gagniuc <mr.nuke.me@gmail.com> Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For any failure after nvme_rdma_start_queue in
nvme_rdma_configure_admin_queue, the admin queue will be freed with the
NVME_RDMA_Q_LIVE flag still set. Once nvme_rdma_stop_queue is invoked,
that will cause a use-after-free.
BUG: KASAN: use-after-free in rdma_disconnect+0x1f/0xe0 [rdma_cm]
To fix it, call nvme_rdma_stop_queue for all the failed cases after
nvme_rdma_start_queue.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Suggested-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The `s2idle_lock' is acquired during suspend while interrupts are
disabled even on RT. The lock is acquired for short sections only.
Make it a RAW lock which avoids "sleeping while atomic" warnings on RT.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Under the following case, qgroup rescan can double account cowed tree
blocks:
In this case, extent tree only has one tree block.
-
| transid=5 last committed=4
| btrfs_qgroup_rescan_worker()
| |- btrfs_start_transaction()
| | transid = 5
| |- qgroup_rescan_leaf()
| |- btrfs_search_slot_for_read() on extent tree
| Get the only extent tree block from commit root (transid = 4).
| Scan it, set qgroup_rescan_progress to the last
| EXTENT/META_ITEM + 1
| now qgroup_rescan_progress = A + 1.
|
| fs tree get CoWed, new tree block is at A + 16K
| transid 5 get committed
-
| transid=6 last committed=5
| btrfs_qgroup_rescan_worker()
| btrfs_qgroup_rescan_worker()
| |- btrfs_start_transaction()
| | transid = 5
| |- qgroup_rescan_leaf()
| |- btrfs_search_slot_for_read() on extent tree
| Get the only extent tree block from commit root (transid = 5).
| scan it using qgroup_rescan_progress (A + 1).
| found new tree block beyong A, and it's fs tree block,
| account it to increase qgroup numbers.
-
In above case, tree block A, and tree block A + 16K get accounted twice,
while qgroup rescan should stop when it already reach the last leaf,
other than continue using its qgroup_rescan_progress.
Such case could happen by just looping btrfs/017 and with some
possibility it can hit such double qgroup accounting problem.
Fix it by checking the path to determine if we should finish qgroup
rescan, other than relying on next loop to exit.
Reported-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently the code assumes that there's an implied barrier by the
sequence of code preceding the wakeup, namely the mutex unlock.
As Nikolay pointed out:
I think this is wrong (not your code) but the original assumption that
the RELEASE semantics provided by mutex_unlock is sufficient.
According to memory-barriers.txt:
Section 'LOCK ACQUISITION FUNCTIONS' states:
(2) RELEASE operation implication:
Memory operations issued before the RELEASE will be completed before the
RELEASE operation has completed.
Memory operations issued after the RELEASE *may* be completed before the
RELEASE operation has completed.
So if we assume that *C is modifying the flag which the waitqueue is checking,
and *E is the actual wakeup, then those accesses can be re-ordered...
IMHO this code should be considered broken... Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In btrfs_evict_inode(), if btrfs_truncate_inode_items() fails, the inode
item will still be in the tree but we still return the ino to the ino
cache. That will blow up later when someone tries to allocate that ino,
so don't return it to the cache.
Fixes: 581bb050941b ("Btrfs: Cache free inode numbers in memory") Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When a buffer is queued or requeued in vb2_buffer_done, then don't
call the finish memop. In this case the buffer is only returned to vb2,
not to userspace.
Calling 'finish' here will cause an unbalance when the queue is
canceled, since the core will call the same memop again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the driver is configured in the "memcpy" dma-mode,
it uses vb2_vmalloc_memops, which is backed by a SLAB
allocator and so shouldn't be using GFP_DMA32.
Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
the wl pointer can be null In case only wlcore_sdio is probed while
no WiLink module is successfully probed, as in the case of mounting a
wl12xx module while using a device tree file configured with wl18xx
related settings.
In this case the system was crashing in wl1271_suspend() as platform
device data is not set.
Make sure wl the pointer is valid before using it.
Signed-off-by: Eyal Reizer <eyalr@ti.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If we cannot communicate with the EC chip to detect the protocol version
and its features, it's very likely useless to continue. Else we will
commit all kind of uninformed mistakes (using the wrong protocol, the
wrong buffer size, mixing the EC with other chips).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Acked-by: Benson Leung <bleung@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In case, one BE is used by two FE1/FE2
FE1--->BE-->
|
FE2----]
when FE1/FE2 call dpcm_be_dai_hw_free() together
the BE users will be 2 (> 1), hence cannot be hw_free
the be state will leave at, ex. SND_SOC_DPCM_STATE_STOP
later FE1/FE2 call dpcm_be_dai_shutdown(),
will be skip due to wrong state.
leaving the BE not being hw_free and shutdown.
The BE dai will be hw_free later when calling
dpcm_be_dai_shutdown() if still in invalid state.
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This patch fixes the following warning during boot:
do not call blocking ops when !TASK_RUNNING; state=1 set at
[<(ptrval)>] qca_setup+0x194/0x750 [hci_uart]
WARNING: CPU: 2 PID: 1878 at kernel/sched/core.c:6135
__might_sleep+0x7c/0x88
In qca_set_baudrate(), the current task state is set to
TASK_UNINTERRUPTIBLE before going to sleep for 300ms. It was then
restored to TASK_INTERRUPTIBLE. This patch sets the current task state
back to TASK_RUNNING instead.
Make sure the rx_allocator worker is canceled before running the
rx_init routine. rx_init frees and re-allocates all rxb's pages. The
rx_allocator worker also allocates pages for the used rxb's. Running
rx_init and rx_allocator simultaniously causes a kernel panic. Fix
that by canceling the work in rx_init.
When intel_pstate test is skipped because of unmet dependencies and/or
unsupported configuration, it returns 0 which is treated as a pass
by the Kselftest framework. This leads to false positive result even
when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
When memfd test is skipped because of unmet dependencies and/or unsupported
configuration, it returns non-zero value which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the test
could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Added an explicit check for root user at the start of memfd hugetlbfs test
and return skip code if a non-root user attempts to run it.
In addition, return skip code when not enough huge pages are available to
run the test.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
A few changes improve the overall usability of the test:
* fix a hard-coded maximum frequency (3300),
* don't adjust the CPU frequency if only evaluating results,
* fix a comparison for multiple frequencies.
A symptom of that last issue looked like this:
./run.sh: line 107: [: too many arguments
./run.sh: line 110: 3099
3099
3100-3100: syntax error in expression (error token is \"3099
3100-3100\")
Because a check will count how many differente frequencies
there are among the CPUs of the system, and after they are
tallied another read is performed, which might produce
different results.
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org> Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>