Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022c7 ("bnxt_en: Need memory barrier when processing the completion ring.") Reported-by: Lance Richardson <lance.richardson@broadcom.com> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Reviewed-by: Lance Richardson <lance.richardson@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple
filters are inserted and deleted by the 212 firmware.
Fixes: ae10ae740ad2 ("bnxt_en: Add new hardware RFS mode.") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
During the swap dependency on PCH_GBE to selection PTP_1588_CLOCK_PCH
incidentally dropped the implicit dependency on the PCI. Restore it.
Fixes: 18d359ceb044 ("pch_gbe, ptp_pch: Fix the dependency direction between these drivers") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Syzbot reported slab-out-of bounds write in decode_data().
The problem was in missing validation checks.
Syzbot's reproducer generated malicious input, which caused
decode_data() to be called a lot in sixpack_decode(). Since
rx_count_cooked is only 400 bytes and noone reported before,
that 400 bytes is not enough, let's just check if input is malicious
and complain about buffer overrun.
Fail log:
==================================================================
BUG: KASAN: slab-out-of-bounds in drivers/net/hamradio/6pack.c:843
Write of size 1 at addr ffff888087c5544e by task kworker/u4:0/7
Reported-and-tested-by: syzbot+fc8cd9a673d4577fb2e4@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.
Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.
The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.
Noticed while reading the code.
Fixes: 4d172f21cefe ("bnxt_en: Implement xmit_more.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca73 ("bnxt_en: cleanup DIM work on device shutdown") Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
"access skb fields ok" verifier test fails on s390 with the "verifier
bug. zext_dst is set, but no reg is defined" message. The first insns
of the test prog are ...
... and the 3rd one is dead (this does not look intentional to me, but
this is a separate topic).
sanitize_dead_code() converts dead insns into "ja -1", but keeps
zext_dst. When opt_subreg_zext_lo32_rnd_hi32() tries to parse such
an insn, it sees this discrepancy and bails. This problem can be seen
only with JITs whose bpf_jit_needs_zext() returns true.
Fix by clearning dead insns' zext_dst.
The commits that contributed to this problem are:
1. 5aa5bd14c5f8 ("bpf: add initial suite for selftests"), which
introduced the test with the dead code.
2. 5327ed3d44b7 ("bpf: verifier: mark verified-insn with
sub-register zext flag"), which introduced the zext_dst flag.
3. 83a2881903f3 ("bpf: Account for BPF_FETCH in
insn_has_def32()"), which introduced the sanity check.
4. 9183671af6db ("bpf: Fix leakage under speculation on
mispredicted branches"), which bisect points to.
It's best to fix this on stable branches that contain the second one,
since that's the point where the inconsistency was introduced.
Fixes: 5327ed3d44b7 ("bpf: verifier: mark verified-insn with sub-register zext flag") Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20210812151811.184086-2-iii@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The orginal setting is not correct, fix it to follow hardware data sheet.
If keep this error setting, mt8173/mt8183 display ok
but mt8192 display abnormal.
Fixes: 0664d1392c26 ("drm/mediatek: Add AAL engine basic function") Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com> Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The current code treats an empty iotlb provdied in set_map() as a
special case and destroy the memory region object. This must not be done
since the virtqueue objects reference this MR. Doing so will cause the
driver unload to emit errors and log timeouts caused by the firmware
complaining on busy resources.
This patch treats an empty iotlb as any other change of mapping. In this
case, mlx5_vdpa_create_mr() will fail and the entire set_map() call to
fail.
This issue has not been encountered before but was seen to occur in a
non-official version of qemu. Since qemu is a userspace program, the
driver must protect against such case.
Fixes: 94abbccdf291 ("vdpa/mlx5: Add shared memory registration code") Signed-off-by: Eli Cohen <elic@nvidia.com> Link: https://lore.kernel.org/r/20210811053713.66658-1-elic@nvidia.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This fixes the incorrect calculation for integer overflow
when the last address of iova range is 0xffffffff.
Fixes: ec33d031a14b ("vhost: detect 32 bit integer wrap around") Reported-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Xie Yongji <xieyongji@bytedance.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20210728130756.97-2-xieyongji@bytedance.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We have changed the return type for sysc_check_active_timer() from -EBUSY
to -ENXIO, but the gpt12 system timer fix still checks for -EBUSY. We are
also not returning on other errors like we did earlier as noted by
Pavel Machek <pavel@denx.de>.
Commit 3ff340e24c9d ("bus: ti-sysc: Fix gpt12 system timer issue with
reserved status") should have been updated for commit 65fb73676112
("bus: ti-sysc: suppress err msg for timers used as clockevent/source").
Let's fix the issue by checking for -ENXIO and returning on any other
errors as suggested by Pavel Machek <pavel@denx.de>.
Fixes: 3ff340e24c9d ("bus: ti-sysc: Fix gpt12 system timer issue with reserved status")
Depends-on: 65fb73676112 ("bus: ti-sysc: suppress err msg for timers used as clockevent/source") Reported-by: Pavel Machek <pavel@denx.de> Reviewed-by: Pavel Machek (CIP) <pavel@denx.de> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Jarkko Nikula <jarkko.nikula@bitmer.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
VQs may be accessed to mark the device broken while they are
created/destroyed. Hence protect the access to the vqs list.
Fixes: e2dcdfe95c0b ("virtio: virtio_break_device() to mark all virtqueues broken.") Signed-off-by: Parav Pandit <parav@nvidia.com> Link: https://lore.kernel.org/r/20210721142648.1525924-4-parav@nvidia.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
GCC complains about empty macros in an 'if' statement, so convert
them to 'do {} while (0)' macros.
Fixes these build warnings:
net/dccp/output.c: In function 'dccp_xmit_packet':
../net/dccp/output.c:283:71: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
283 | dccp_pr_debug("transmit_skb() returned err=%d\n", err);
net/dccp/ackvec.c: In function 'dccp_ackvec_update_old':
../net/dccp/ackvec.c:163:80: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
163 | (unsigned long long)seqno, state);
Fixes: dc841e30eaea ("dccp: Extend CCID packet dequeueing interface") Fixes: 380240864451 ("dccp ccid-2: Update code for the Ack Vector input/registration routine") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: dccp@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The 1.2 GHz variant of the Armada 3720 SOC is unstable with DVFS: when
the SOC boots, the WTMI firmware sets clocks and AVS values that work
correctly with 1.2 GHz CPU frequency, but random crashes occur once
cpufreq driver starts scaling.
We do not know currently what is the reason:
- it may be that the voltage value for L0 for 1.2 GHz variant provided
by the vendor in the OTP is simply incorrect when scaling is used,
- it may be that some delay is needed somewhere,
- it may be something else.
The most sane solution now seems to be to simply forbid the cpufreq
driver on 1.2 GHz variant.
Signed-off-by: Marek Behún <kabel@kernel.org> Fixes: 92ce45fb875d ("cpufreq: Add DVFS support for Armada 37xx") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If probe_device is failing, iommu_group is not initialized because
iommu_group_add_device is not reached, so freeing it will result
in NULL pointer access.
iommu_bus_init
->bus_iommu_probe
->probe_iommu_group in for each:/* return -22 in fail case */
->iommu_probe_device
->__iommu_probe_device /* return -22 here.*/
-> ops->probe_device /* return -22 here.*/
-> iommu_group_get_for_dev
-> ops->device_group
-> iommu_group_add_device //good case
->remove_iommu_group //in fail case, it will remove group
->iommu_release_device
->iommu_group_remove_device // here we don't have group
In my case ops->probe_device (mtk_iommu_probe_device from
mtk_iommu_v1.c) is due to failing fwspec->ops mismatch.
Fixes: d72e31c93746 ("iommu: IOMMU Groups") Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Link: https://lore.kernel.org/r/20210731074737.4573-1-linux@fw-web.de Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
WSA881x powerdown pin is connected to GPIO1, GPIO2 not GPIO2 and GPIO3,
so correct this. This was working so far due to a shift bug in gpio driver,
however once that is fixed this will stop working, so fix this!
For some reason we forgot to add this dts change in last merge cycle so
currently audio is broken in 5.13 as the gpio driver fix already landed
in 5.13.
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.
[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Certain call sites of get_geristers() did not do proper error handling. This
could be a problem as get_geristers() typically return the data via pointer to a
buffer. If an error occurred the code is carelessly manipulating the wrong data.
Signed-off-by: Petko Manolov <petkan@nucleusys.com> Reviewed-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
After adding physical volumes to a volume group through vgextend, the
kernel will rescan the partitions. This in turn will cause the device
capacity to be queried.
If the device status is set to offline through sysfs at this time, READ
CAPACITY command will return a result which the host byte is
DID_NO_CONNECT, and the capacity of the device will be set to zero in
read_capacity_error(). After setting device status back to running, the
capacity of the device will remain stuck at zero.
Fix this issue by rescanning device when the device state changes to
SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210727034455.1494960-1-lijinlin3@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: lijinlin <lijinlin3@huawei.com> Signed-off-by: Wu Bo <wubo40@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Avoid printing a 'target allocation failed' error if the driver
target_alloc() callback function returns -ENXIO. This return value
indicates that the corresponding H:C:T:L entry is empty.
Removing this error reduces the scan time if the user issues SCAN_WILD_CARD
scan operation through sysfs parameter on a host with a lot of empty
H:C:T:L entries.
Avoiding the printk on -ENXIO matches the behavior of the other callback
functions during scanning.
Link: https://lore.kernel.org/r/20210726115402.1936-1-sreekanth.reddy@broadcom.com Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix the race between rdac_bus_attach() and rdac_bus_detach() where h->sdev
is NULL when processing the RDAC attach.
Link: https://lore.kernel.org/r/20210113063103.2698953-1-yebin10@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The list_for_each_entry() iterator, "adapter" in this code, can never be
NULL. If we exit the loop without finding the correct adapter then
"adapter" points invalid memory that is an offset from the list head. This
will eventually lead to memory corruption and presumably a kernel crash.
Link: https://lore.kernel.org/r/20210708074642.23599-1-harshvardhan.jha@oracle.com Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The TMF timeout timer may trigger at the same time when the response from a
controller is being handled. When this happens the SAS task may get freed
before the response processing is finished.
Fix this by calling complete() only when SAS_TASK_STATE_DONE is not set.
A similar race condition was fixed in commit b90cd6f2b905 ("scsi: libsas:
fix a race condition when smp task timeout")
Link: https://lore.kernel.org/r/20210707185945.35559-1-ipylypiv@google.com Reviewed-by: Vishakha Channapattan <vishakhavc@google.com> Acked-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Igor Pylypiv <ipylypiv@google.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If the router_xlate can not find the controller in the available DMA
devices then it should return with -EPORBE_DEFER in a same way as the
of_dma_request_slave_channel() does.
The issue can be reproduced if the event router is registered before the
DMA controller itself and a driver would request for a channel before the
controller is registered.
In of_dma_request_slave_channel():
1. of_dma_find_controller() would find the dma_router
2. ofdma->of_dma_xlate() would fail and returned NULL
3. -ENODEV is returned as error code
with this patch we would return in this case the correct -EPROBE_DEFER and
the client can try to request the channel later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com> Link: https://lore.kernel.org/r/20210717190021.21897-1-peter.ujfalusi@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by moving the error_pm label above the pm_runtime_put() in
the error path.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20210706124521.1371901-1-yukuai3@huawei.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When user calls dmaengine_terminate_sync, the driver will clean up any
remaining descriptors for all the pending or active transfers that had
previously been submitted. However, this might happen whilst the tasklet is
invoking the DMA callback for the last finished transfer, so by the time it
returns and takes over the channel's spinlock, the list of completed
descriptors it was traversing is no longer valid. This leads to a
read-after-free situation.
Fix it by signalling whether a user-triggered termination has happened by
means of a boolean variable.
Signed-off-by: Adrian Larumbe <adrian.martinezlarumbe@imgtec.com> Link: https://lore.kernel.org/r/20210706234338.7696-3-adrian.martinezlarumbe@imgtec.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the user submits a control URB via usbfs, the user supplies the
bRequestType value and the kernel uses it to compute the pipe value.
However, do_proc_control() performs this computation incorrectly in
the case where the bRequestType direction bit is set to USB_DIR_IN and
the URB's transfer length is 0: The pipe's direction is also set to IN
but it should be OUT, which is the direction the actual transfer will
use regardless of bRequestType.
Commit 5cc59c418fde ("USB: core: WARN if pipe direction != setup
packet direction") added a check to compare the direction bit in the
pipe value to a control URB's actual direction and to WARN if they are
different. This can be triggered by the incorrect computation
mentioned above, as found by syzbot.
This patch fixes the computation, thus avoiding the WARNing.
Reported-and-tested-by: syzbot+72af3105289dcb4c055b@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20210712185436.GB326369@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The USB core has utility routines to retrieve various types of
descriptors. These routines will now provoke a WARN if they are asked
to retrieve 0 bytes (USB "receive" requests must not have zero
length), so avert this by checking the size argument at the start.
CC: Johan Hovold <johan@kernel.org> Reported-and-tested-by: syzbot+7dbcd9ff34dc4ed45240@syzkaller.appspotmail.com Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20210607152307.GD1768031@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Erasing an AMD linear flash card (AM29F016D) crashes after the first
sector has been erased. Likewise, writing to it crashes after two bytes
have been written. The reason is a missing check for a null pointer -
the cmdset_priv field is not set for this type of card.
Fixes: 4844ef80305d ("mtd: cfi_cmdset_0002: Add support for polling status register") Signed-off-by: Andreas Persson <andreasp56@outlook.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/DB6P189MB05830B3530B8087476C5CFE4C1159@DB6P189MB0583.EURP189.PROD.OUTLOOK.COM Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Do not delete a key cache entry that is still being referenced by
pending frames in TXQs. This avoids reuse of the key cache entry while a
frame might still be transmitted using it.
To avoid having to do any additional operations during the main TX path
operations, track pending key cache entries in a new bitmap and check
whether any pending entries can be deleted before every new key
add/remove operation. Also clear any remaining entries when stopping the
interface.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201214172118.18100-6-jouni@codeaurora.org Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
tkip_keymap can be used internally to avoid the reference to key->cipher
and with this, only the key index value itself is needed. This allows
ath_key_delete() call to be postponed to be handled after the upper
layer STA and key entry have already been removed. This is needed to
make ath9k key cache management safer.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201214172118.18100-5-jouni@codeaurora.org Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Now that ath/key.c may not be explicitly clearing keys from the key
cache, clear all key cache entries when disabling hardware to make sure
no keys are left behind beyond this point.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201214172118.18100-3-jouni@codeaurora.org Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It is possible for there to be pending frames in TXQs with a reference
to the key cache entry that is being deleted. If such a key cache entry
is cleared, those pending frame in TXQ might get transmitted without
proper encryption. It is safer to leave the previously used key into the
key cache in such cases. Instead, only clear the MAC address to prevent
RX processing from using this key cache entry.
This is needed in particularly in AP mode where the TXQs cannot be
flushed on station disconnection. This change alone may not be able to
address all cases where the key cache entry might get reused for other
purposes immediately (the key cache entry should be released for reuse
only once the TXQs do not have any remaining references to them), but
this makes it less likely to get unprotected frames and the more
complete changes may end up being significantly more complex.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201214172118.18100-2-jouni@codeaurora.org Cc: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The address still includes the tags when it is printed. With hardware
tag-based kasan enabled, we will get a false positive KASAN issue when
we access metadata.
Reset the tag before we access the metadata.
Link: https://lkml.kernel.org/r/20210804090957.12393-3-Kuan-Ying.Lee@mediatek.com Fixes: aa1ef4d7b3f6 ("kasan, mm: reset tags when accessing metadata") Signed-off-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com> Reviewed-by: Marco Elver <elver@google.com> Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chinwen Chang <chinwen.chang@mediatek.com> Cc: Nicholas Tang <nicholas.tang@mediatek.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: e4b27ebc780f ("net: dsa: Add DSA driver for Hirschmann Hellcreek switches") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
SMC clients may be assigned to a different link after the initial
connection between two peers was established. In such a case,
the connection counter was not correctly set.
Update the connection counter correctly when a smc client connection
is assigned to a different smc link.
Fixes: 07d51580ff65 ("net/smc: Add connection counters for links") Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com> Tested-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Before this patch, btf_new() was liable to close an arbitrary FD 0 if
BTF parsing failed. This was because:
* btf->fd was initialized to 0 through the calloc()
* btf__free() (in the `done` label) closed any FDs >= 0
* btf->fd is left at 0 if parsing fails
This issue was discovered on a system using libbpf v0.3 (without
BTF_KIND_FLOAT support) but with a kernel that had BTF_KIND_FLOAT types
in BTF. Thus, parsing fails.
While this patch technically doesn't fix any issues b/c upstream libbpf
has BTF_KIND_FLOAT support, it'll help prevent issues in the future if
more BTF types are added. It also allow the fix to be backported to
older libbpf's.
Fixes: 3289959b97ca ("libbpf: Support BTF loading and raw data output in both endianness") Signed-off-by: Daniel Xu <dxu@dxuuu.xyz> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/5969bb991adedb03c6ae93e051fd2a00d293cf25.1627513670.git.dxu@dxuuu.xyz Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
'watermarks_table' must be freed instead 'clocks_table', because
'clocks_table' is known to be NULL at this point and 'watermarks_table' is
never freed if the last kzalloc fails.
Fixes: c98ee89736b8 ("drm/amd/pm: add the fine grain tuning function for vangogh") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Q1 and Q2 are numbers with *maximum* length of 384 bytes. If the
calculated length of Q1 and Q2 is less than 384 bytes, things will
go wrong.
E.g. if Q2 is 383 bytes, then
1. The bytes of q2 are copied to sigstruct->q2 in calc_q1q2().
2. The entire sigstruct->q2 is reversed, which results it being
256 * Q2, given that the last byte of sigstruct->q2 is added
to before the bytes given by calc_q1q2().
Either change in key or measurement can trigger the bug. E.g. an
unmeasured heap could cause a devastating change in Q1 or Q2.
Reverse exactly the bytes of Q1 and Q2 in calc_q1q2() before returning
to the caller.
Fixes: 2adcba79e69d ("selftests/x86: Add a selftest for SGX") Link: https://lore.kernel.org/linux-sgx/20210301051836.30738-1-tianjia.zhang@linux.alibaba.com/ Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The physical address may exceed 32 bits on 32-bit systems with more than
32 bits of physcial address. Use PFN_PHYS() in devmem_is_allowed(), or
the physical address may overflow and be truncated.
We found this bug when mapping a high addresses through devmem tool,
when CONFIG_STRICT_DEVMEM is enabled on the ARM with ARM_LPAE and devmem
is used to map a high address that is not in the iomem address range, an
unexpected error indicating no permission is returned.
This bug was initially introduced from v2.6.37, and the function was
moved to lib in v5.11.
Link: https://lkml.kernel.org/r/20210731025057.78825-1-wangliang101@huawei.com Fixes: 087aaffcdf9c ("ARM: implement CONFIG_STRICT_DEVMEM by disabling access to RAM via /dev/mem") Fixes: 527701eda5f1 ("lib: Add a generic version of devmem_is_allowed()") Signed-off-by: Liang Wang <wangliang101@huawei.com> Reviewed-by: Luis Chamberlain <mcgrof@kernel.org> Cc: Palmer Dabbelt <palmerdabbelt@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Russell King <linux@armlinux.org.uk> Cc: Liang Wang <wangliang101@huawei.com> Cc: Xiaoming Ni <nixiaoming@huawei.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: <stable@vger.kernel.org> [2.6.37+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On the CPU port, we can support both tagged and untagged VLANs at the
same time by doing any necessary untagging in software rather than
hardware. To enable that, keep the CPU port's Remove Tag flag cleared
and set the dsa_switch::untag_bridge_pvid flag.
Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10: adjust context] Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When a VLAN is deleted from a port, the flags in struct
switchdev_obj_port_vlan are always 0. ksz8_port_vlan_del() copies the
BRIDGE_VLAN_INFO_UNTAGGED flag to the port's Tag Removal flag, and
therefore always clears it.
In case there are multiple VLANs configured as untagged on this port -
which seems useless, but is allowed - deleting one of them changes the
remaining VLANs to be tagged.
It's only ever necessary to change this flag when a VLAN is added to
the port, so leave it unchanged in ksz8_port_vlan_del().
Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10: adjust context] Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The switches supported by ksz8795 only have a per-port flag for Tag
Removal. This means it is not possible to support both tagged and
untagged VLANs on the same port. Reject attempts to add a VLAN that
requires the flag to be changed, unless there are no VLANs currently
configured.
VID 0 is excluded from this check since it is untagged regardless of
the state of the flag.
On the CPU port we could support tagged and untagged VLANs at the same
time. This will be enabled by a later patch.
Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10:
- This configuration has to be detected and rejected in the
port_vlan_prepare operation
- ksz8795_port_vlan_add() has to check again to decide whether to
change the Tag Removal flag, so put the common condition in a
separate function
- Handle VID ranges] Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
ksz8795 has never actually enabled PVID tag insertion, and it also
programmed the PVID incorrectly. To fix this:
* Allow tag insertion to be controlled per ingress port. On most
chips, set bit 2 in Global Control 19. On KSZ88x3 this control
flag doesn't exist.
* When adding a PVID:
- Set the appropriate register bits to enable tag insertion on
egress at every other port if this was the packet's ingress port.
- Mask *out* the VID from the default tag, before or-ing in the new
PVID.
* When removing a PVID:
- Clear the same control bits to disable tag insertion.
- Don't update the default tag. This wasn't doing anything useful.
Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver") Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backport to 5.10:
- Drop the KSZ88x3 cases as those chips are not supported here
- Handle VID ranges in ksz8795_port_vlan_del()] Signed-off-by: Ben Hutchings <ben.hutchings@mind.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
A recent change in LLVM causes module_{c,d}tor sections to appear when
CONFIG_K{A,C}SAN are enabled, which results in orphan section warnings
because these are not handled anywhere:
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_ctor) is being placed in '.text.asan.module_ctor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.asan.module_dtor) is being placed in '.text.asan.module_dtor'
ld.lld: warning: arch/x86/pci/built-in.a(legacy.o):(.text.tsan.module_ctor) is being placed in '.text.tsan.module_ctor'
Fangrui explains: "the function asan.module_ctor has the SHF_GNU_RETAIN
flag, so it is in a separate section even with -fno-function-sections
(default)".
Place them in the TEXT_TEXT section so that these technologies continue
to work with the newer compiler versions. All of the KASAN and KCSAN
KUnit tests continue to pass after this change.
There is a race in ceph_put_snap_realm. The change to the nref and the
spinlock acquisition are not done atomically, so you could decrement
nref, and before you take the spinlock, the nref is incremented again.
At that point, you end up putting it on the empty list when it
shouldn't be there. Eventually __cleanup_empty_realms runs and frees
it when it's still in-use.
Fix this by protecting the 1->0 transition with atomic_dec_and_lock,
and just drop the spinlock if we can get the rwsem.
Because these objects can also undergo a 0->1 refcount transition, we
must protect that change as well with the spinlock. Increment locklessly
unless the value is at 0, in which case we take the spinlock, increment
and then take it off the empty list if it did the 0->1 transition.
With these changes, I'm removing the dout() messages from these
functions, as well as in __put_snap_realm. They've always been racy, and
it's better to not print values that may be misleading.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/46419 Reported-by: Mark Nelson <mnelson@redhat.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Luis Henriques <lhenriques@suse.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
They both say that the snap_rwsem must be held for write, but I don't
see any real reason for it, and it's not currently always called that
way.
The lookup is just walking the rbtree, so holding it for read should be
fine there. The "get" is bumping the refcount and (possibly) removing
it from the empty list. I see no need to hold the snap_rwsem for write
for that.
Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use vmx_need_pf_intercept() when determining if L0 wants to handle a #PF
in L2 or if the VM-Exit should be forwarded to L1. The current logic fails
to account for the case where #PF is intercepted to handle
guest.MAXPHYADDR < host.MAXPHYADDR and ends up reflecting all #PFs into
L1. At best, L1 will complain and inject the #PF back into L2. At
worst, L1 will eat the unexpected fault and cause L2 to hang on infinite
page faults.
Note, while the bug was technically introduced by the commit that added
support for the MAXPHYADDR madness, the shame is all on commit a0c134347baf ("KVM: VMX: introduce vmx_need_pf_intercept").
Fixes: 1dbf5d68af6f ("KVM: VMX: Add guest physical address check in EPT violation and misconfig") Cc: stable@vger.kernel.org Cc: Peter Shier <pshier@google.com> Cc: Oliver Upton <oupton@google.com> Cc: Jim Mattson <jmattson@google.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210812045615.3167686-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use the secondary_exec_controls_get() accessor in vmx_has_waitpkg() to
effectively get the controls for the current VMCS, as opposed to using
vmx->secondary_exec_controls, which is the cached value of KVM's desired
controls for vmcs01 and truly not reflective of any particular VMCS.
While the waitpkg control is not dynamic, i.e. vmcs01 will always hold
the same waitpkg configuration as vmx->secondary_exec_controls, the same
does not hold true for vmcs02 if the L1 VMM hides the feature from L2.
If L1 hides the feature _and_ does not intercept MSR_IA32_UMWAIT_CONTROL,
L2 could incorrectly read/write L1's virtual MSR instead of taking a #GP.
Fixes: 6e3ba4abcea5 ("KVM: vmx: Emulate MSR IA32_UMWAIT_CONTROL") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210810171952.2758100-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On arm64, the stub only moves the kernel image around in memory if
needed, which is typically only for KASLR, given that relocatable
kernels (which is the default) can run from any 64k aligned address,
which is also the minimum alignment communicated to EFI via the PE/COFF
header.
Unfortunately, some loaders appear to ignore this header, and load the
kernel at some arbitrary offset in memory. We can deal with this, but
let's check for this condition anyway, so non-compliant code can be
spotted and fixed.
Cc: <stable@vger.kernel.org> # v5.10+ Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Multi-MSI uses a single MSI descriptor and there is a single mask register
when the device supports per vector masking. To avoid reading back the mask
register the value is cached in the MSI descriptor and updates are done by
clearing and setting bits in the cache and writing it to the device.
But nothing protects msi_desc::masked and the mask register from being
modified concurrently on two different CPUs for two different Linux
interrupts which belong to the same multi-MSI descriptor.
Add a lock to struct device and protect any operation on the mask and the
mask register with it.
This makes the update of msi_desc::masked unconditional, but there is no
place which requires a modification of the hardware register without
updating the masked cache.
msi_mask_irq() is now an empty wrapper which will be cleaned up in follow
up changes.
The problem goes way back to the initial support of multi-MSI, but picking
the commit which introduced the mask cache is a valid cut off point
(2.6.30).
Fixes: f2440d9acbe8 ("PCI MSI: Refactor interrupt masking code") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.726833414@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The comments about preserving the cached state in pci_msi[x]_shutdown() are
misleading as the MSI descriptors are freed right after those functions
return. So there is nothing to restore. Preparatory change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.621609423@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
msi_mask_irq() takes a mask and a flags argument. The mask argument is used
to mask out bits from the cached mask and the flags argument to set bits.
Some places invoke it with a flags argument which sets bits which are not
used by the device, i.e. when the device supports up to 8 vectors a full
unmask in some places sets the mask to 0xFFFFFF00. While devices probably
do not care, it's still bad practice.
Fixes: 7ba1930db02f ("PCI MSI: Unmask MSI if setup failed") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.568173099@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Nothing enforces the posted writes to be visible when the function
returns. Flush them even if the flush might be redundant when the entry is
masked already as the unmask will flush as well. This is either setup or a
rare affinity change event so the extra flush is not the end of the world.
While this is more a theoretical issue especially the logic in the X86
specific msi_set_affinity() function relies on the assumption that the
update has reached the hardware when the function returns.
Again, as this never has been enforced the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.515188147@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The specification (PCIe r5.0, sec 6.1.4.5) states:
For MSI-X, a function is permitted to cache Address and Data values
from unmasked MSI-X Table entries. However, anytime software unmasks a
currently masked MSI-X Table entry either by clearing its Mask bit or
by clearing the Function Mask bit, the function must update any Address
or Data values that it cached from that entry. If software changes the
Address or Data value of an entry while the entry is unmasked, the
result is undefined.
The Linux kernel's MSI-X support never enforced that the entry is masked
before the entry is modified hence the Fixes tag refers to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Enforce the entry to be masked across the update.
There is no point in enforcing this to be handled at all possible call
sites as this is just pointless code duplication and the common update
function is the obvious place to enforce this.
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support") Reported-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.462096385@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
1) msix_setup_entries() allocates the MSI descriptors and initializes them
except for the msi_desc:masked member which is left zero initialized.
2) pci_msi_setup_msi_irqs() allocates the interrupt descriptors and sets
up the MSI interrupts which ends up in pci_write_msi_msg() unless the
interrupt chip provides its own irq_write_msi_msg() function.
3) msix_program_entries() does not do what the name suggests. It solely
updates the entries array (if not NULL) and initializes the masked
member for each MSI descriptor by reading the hardware state and then
masks the entry.
Obviously this has some issues:
1) The uninitialized masked member of msi_desc prevents the enforcement
of masking the entry in pci_write_msi_msg() depending on the cached
masked bit. Aside of that half initialized data is a NONO in general
2) msix_program_entries() only ensures that the actually allocated entries
are masked. This is wrong as experimentation with crash testing and
crash kernel kexec has shown.
This limited testing unearthed that when the production kernel had more
entries in use and unmasked when it crashed and the crash kernel
allocated a smaller amount of entries, then a full scan of all entries
found unmasked entries which were in use in the production kernel.
This is obviously a device or emulation issue as the device reset
should mask all MSI-X table entries, but obviously that's just part
of the paper specification.
Cure this by:
1) Masking all table entries in hardware
2) Initializing msi_desc::masked in msix_setup_entries()
3) Removing the mask dance in msix_program_entries()
4) Renaming msix_program_entries() to msix_update_entries() to
reflect the purpose of that function.
As the masking of unused entries has never been done the Fixes tag refers
to a commit in:
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: f036d4ea5fa7 ("[PATCH] ia32 Message Signalled Interrupt support") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.403833459@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The ordering of MSI-X enable in hardware is dysfunctional:
1) MSI-X is disabled in the control register
2) Various setup functions
3) pci_msi_setup_msi_irqs() is invoked which ends up accessing
the MSI-X table entries
4) MSI-X is enabled and masked in the control register with the
comment that enabling is required for some hardware to access
the MSI-X table
Step #4 obviously contradicts #3. The history of this is an issue with the
NIU hardware. When #4 was introduced the table access actually happened in
msix_program_entries() which was invoked after enabling and masking MSI-X.
This was changed in commit d71d6432e105 ("PCI/MSI: Kill redundant call of
irq_set_msi_desc() for MSI-X interrupts") which removed the table write
from msix_program_entries().
Interestingly enough nobody noticed and either NIU still works or it did
not get any testing with a kernel 3.19 or later.
Nevertheless this is inconsistent and there is no reason why MSI-X can't be
enabled and masked in the control register early on, i.e. move step #4
above to step #1. This preserves the NIU workaround and has no side effects
on other hardware.
Fixes: d71d6432e105 ("PCI/MSI: Kill redundant call of irq_set_msi_desc() for MSI-X interrupts") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.344136412@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the interrupt interval is greater than 2 ^ PREDICTION_BUFFER_SIZE *
PREDICTION_FACTOR us and less than 1s, the calculated index will be greater
than the length of irqs->ema_time[]. Check the calculated index before
using it to prevent array overflow.
Fixes: 23aa3b9a6b7d ("genirq/timings: Encapsulate storing function") Signed-off-by: Ben Dai <ben.dai@unisoc.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210425150903.25456-1-ben.dai9703@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
msi_domain_alloc_irqs() invokes irq_domain_activate_irq(), but
msi_domain_free_irqs() does not enforce deactivation before tearing down
the interrupts.
This happens when PCI/MSI interrupts are set up and never used before being
torn down again, e.g. in error handling pathes. The only place which cleans
that up is the error handling path in msi_domain_alloc_irqs().
Move the cleanup from msi_domain_alloc_irqs() into msi_domain_free_irqs()
to cure that.
Fixes: f3b0946d629c ("genirq/msi: Make sure PCI MSIs are activated early") Signed-off-by: Bixuan Cui <cuibixuan@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210518033117.78104-1-cuibixuan@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Creating a new sub monitoring group in the root /sys/fs/resctrl leads to
getting the "Unavailable" value for mbm_total_bytes and mbm_local_bytes
on the entire filesystem.
When a new monitoring group is created, a new RMID is assigned to the
new group. But the RMID is not active yet. When the events are read on
the new RMID, it is expected to report the status as "Unavailable".
When the user reads the events on the default monitoring group with
multiple subgroups, the events on all subgroups are consolidated
together. Currently, if any of the RMID reads report as "Unavailable",
then everything will be reported as "Unavailable".
Fix the issue by discarding the "Unavailable" reads and reporting all
the successful RMID reads. This is not a problem on Intel systems as
Intel reports 0 on Inactive RMIDs.
The IO/APIC cannot handle interrupt affinity changes safely after startup
other than from an interrupt handler. The startup sequence in the generic
interrupt code violates that assumption.
Mark the irq chip with the new IRQCHIP_AFFINITY_PRE_STARTUP flag so that
the default interrupt setting happens before the interrupt is started up
for the first time.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.832143400@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The X86 MSI mechanism cannot handle interrupt affinity changes safely after
startup other than from an interrupt handler, unless interrupt remapping is
enabled. The startup sequence in the generic interrupt code violates that
assumption.
Mark the irq chips with the new IRQCHIP_AFFINITY_PRE_STARTUP flag so that
the default interrupt setting happens before the interrupt is started up
for the first time.
While the interrupt remapping MSI chip does not require this, there is no
point in treating it differently as this might spare an interrupt to a CPU
which is not in the default affinity mask.
For the non-remapping case go to the direct write path when the interrupt
is not yet started similar to the not yet activated case.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.886722080@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
X86 IO/APIC and MSI interrupts (when used without interrupts remapping)
require that the affinity setup on startup is done before the interrupt is
enabled for the first time as the non-remapped operation mode cannot safely
migrate enabled interrupts from arbitrary contexts. Provide a new irq chip
flag which allows affected hardware to request this.
This has to be opt-in because there have been reports in the past that some
interrupt chips cannot handle affinity setting before startup.
Fixes: 18404756765c ("genirq: Expose default irq affinity mask (take 3)") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210729222542.779791738@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Skip (omit) any version string info that is parenthesized.
Warning: objdump version 15) is older than 2.19
Warning: Skipping posttest.
where 'objdump -v' says:
GNU objdump (GNU Binutils; SUSE Linux Enterprise 15) 2.35.1.20201123-7.18
Fixes: 8bee738bb1979 ("x86: Fix objdump version check in chkobjdump.awk for different formats.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org> Link: https://lore.kernel.org/r/20210731000146.2720-1-rdunlap@infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is no real mode for booke arch and the MMU translation is
always on. The corresponding MSR_IS/MSR_DS bit in booke is used
to switch the address space, but not for real mode judgment.
Fixes: 21f8b2fa3ca5 ("powerpc/kprobes: Ignore traps that happened in real mode") Signed-off-by: Pu Lehui <pulehui@huawei.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210809023658.218915-1-pulehui@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Commit 82046702e288 ("efi/libstub/arm64: Replace 'preferred' offset with
alignment check") simplified the way the stub moves the kernel image
around in memory before booting it, given that a relocatable image does
not need to be copied to a 2M aligned offset if it was loaded on a 64k
boundary by EFI.
Commit d32de9130f6c ("efi/arm64: libstub: Deal gracefully with
EFI_RNG_PROTOCOL failure") inadvertently defeated this logic by
overriding the value of efi_nokaslr if EFI_RNG_PROTOCOL is not
available, which was mistaken by the loader logic as an explicit request
on the part of the user to disable KASLR and any associated relocation
of an Image not loaded on a 2M boundary.
So let's reinstate this functionality, by capturing the value of
efi_nokaslr at function entry to choose the minimum alignment.
Fixes: d32de9130f6c ("efi/arm64: libstub: Deal gracefully with EFI_RNG_PROTOCOL failure") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Distro versions of GRUB replace the usual LoadImage/StartImage calls
used to load the kernel image with some local code that fails to honor
the allocation requirements described in the PE/COFF header, as it
does not account for the image's BSS section at all: it fails to
allocate space for it, and fails to zero initialize it.
Since the EFI stub itself is allocated in the .init segment, which is
in the middle of the image, its BSS section is not impacted by this,
and the main consequence of this omission is that the BSS section may
overlap with memory regions that are already used by the firmware.
So let's warn about this condition, and force image reallocation to
occur in this case, which works around the problem.
Fixes: 82046702e288 ("efi/libstub/arm64: Replace 'preferred' offset with alignment check") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The EFI stub random allocator used for kaslr on arm64 has a subtle
bug. In function get_entry_num_slots() which counts the number of
possible allocation "slots" for the image in a given chunk of free
EFI memory, "last_slot" can become negative if the chunk is smaller
than the requested allocation size.
The test "if (first_slot > last_slot)" doesn't catch it because
both first_slot and last_slot are unsigned.
I chose not to make them signed to avoid problems if this is ever
used on architectures where there are meaningful addresses with the
top bit set. Instead, fix it with an additional test against the
allocation size.
This can cause a boot failure in addition to a loss of randomisation
due to another bug in the arm64 stub fixed separately.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Fixes: 2ddbfc81eac8 ("efi: stub: add implementation of efi_random_alloc()") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is a race between iterating over requests in
nbd_clear_que() and completing requests in recv_work(),
which can lead to double completion of a request.
To fix it, flush the recv worker before iterating over
the requests and don't abort the completed request
while iterating.
Fixes: 96d97e17828f ("nbd: clear_sock on netlink disconnect") Reported-by: Jiang Yadong <jiangyadong@bytedance.com> Signed-off-by: Xie Yongji <xieyongji@bytedance.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Link: https://lore.kernel.org/r/20210813151330.96-1-xieyongji@bytedance.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
lock_sock() may do initiative schedule when the 'sk' is owned by
other thread at the same time, we would receivce a warning message
that "scheduling while atomic".
Even worse, if the next task (selected by the scheduler) try to
release a 'sk', it need to request vsock_table_lock and the deadlock
occur, cause the system into softlockup state.
Call trace:
queued_spin_lock_slowpath
vsock_remove_bound
vsock_remove_sock
virtio_transport_release
__vsock_release
vsock_release
__sock_release
sock_close
__fput
____fput
So we should not require sk_lock in this case, just like the behavior
in vhost_vsock or vmci.
Fixes: 0ea9e1d3a9e3 ("VSOCK: Introduce virtio_transport.ko") Cc: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/r/20210812053056.1699-1-longpeng2@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
There is a TOCTOU issue in set_evtchn_to_irq. Rows in the evtchn_to_irq
mapping are lazily allocated in this function. The check whether the row
is already present and the row initialization is not synchronized. Two
threads can at the same time allocate a new row for evtchn_to_irq and
add the irq mapping to the their newly allocated row. One thread will
overwrite what the other has set for evtchn_to_irq[row] and therefore
the irq mapping is lost. This will trigger a BUG_ON later in
bind_evtchn_to_cpu:
This patch sets evtchn_to_irq rows via a cmpxchg operation so that they
will be set only once. The row is now cleared before writing it to
evtchn_to_irq in order to not create a race once the row is visible for
other threads.
While at it, do not require the page to be zeroed, because it will be
overwritten with -1's in clear_evtchn_to_irq_row anyway.
Signed-off-by: Maximilian Heyne <mheyne@amazon.de> Fixes: d0b075ffeede ("xen/events: Refactor evtchn_to_irq array to be dynamically allocated") Link: https://lore.kernel.org/r/20210812130930.127134-1-mheyne@amazon.de Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The SFC_DONE register lives within the corresponding VD0/VD2/VD4/VD6
forcewake domain and is not accessible if the vdbox in that domain is
fused off and the forcewake is not initialized.
This mistake went unnoticed because until recently we were using the
wrong register offset for the SFC_DONE register; once the register
offset was corrected, we started hitting errors like
Currently if BBR congestion control is initialized after more than 2B
packets have been delivered, depending on the phase of the
tp->delivered counter the tracking of BBR round trips can get stuck.
The bug arises because if tp->delivered is between 2^31 and 2^32 at
the time the BBR congestion control module is initialized, then the
initialization of bbr->next_rtt_delivered to 0 will cause the logic to
believe that the end of the round trip is still billions of packets in
the future. More specifically, the following check will fail
repeatedly:
and thus the connection will take up to 2B packets delivered before
that check will pass and the connection will set:
bbr->round_start = 1;
This could cause many mechanisms in BBR to fail to trigger, for
example bbr_check_full_bw_reached() would likely never exit STARTUP.
This bug is 5 years old and has not been observed, and as a practical
matter this would likely rarely trigger, since it would require
transferring at least 2B packets, or likely more than 3 terabytes of
data, before switching congestion control algorithms to BBR.
This patch is a stable candidate for kernels as far back as v4.9,
when tcp_bbr.c was added.
Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control") Signed-off-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Kevin Yang <yyd@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20210811024056.235161-1-ncardwell@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
After migrating my laptop from 4.19-LTS to 5.4-LTS a while ago I noticed
that my Ethernet port to which a bond and a VLAN interface are attached
appeared to remain up after resuming from suspend with the cable unplugged
(and that problem still persists with 5.10-LTS).
It happens that the following happens:
- the network driver (e1000e here) prepares to suspend, calls e1000e_down()
which calls netif_carrier_off() to signal that the link is going down.
- netif_carrier_off() adds a link_watch event to the list of events for
this device
- the device is completely stopped.
- the machine suspends
- the cable is unplugged and the machine brought to another location
- the machine is resumed
- the queued linkwatch events are processed for the device
- the device doesn't yet have the __LINK_STATE_PRESENT bit and its events
are silently dropped
- the device is resumed with its link down
- the upper VLAN and bond interfaces are never notified that the link had
been turned down and remain up
- the only way to provoke a change is to physically connect the machine
to a port and possibly unplug it.
The state after resume looks like this:
$ ip -br li | egrep 'bond|eth'
bond0 UP e8:6a:64:64:64:64 <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP>
eth0 DOWN e8:6a:64:64:64:64 <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP>
eth0.2@eth0 UP e8:6a:64:64:64:64 <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP>
Placing an explicit call to netdev_state_change() either in the suspend
or the resume code in the NIC driver worked around this but the solution
is not satisfying.
The issue in fact really is in link_watch that loses events while it
ought not to. It happens that the test for the device being present was
added by commit 124eee3f6955 ("net: linkwatch: add check for netdevice
being present to linkwatch_do_dev") in 4.20 to avoid an access to
devices that are not present.
Instead of dropping events, this patch proceeds slightly differently by
postponing their handling so that they happen after the device is fully
resumed.
Fixes: 124eee3f6955 ("net: linkwatch: add check for netdevice being present to linkwatch_do_dev") Link: https://lists.openwall.net/netdev/2018/03/15/62 Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Willy Tarreau <w@1wt.eu> Link: https://lore.kernel.org/r/20210809160628.22623-1-w@1wt.eu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On error path of br_add_if(), p->mcast_stats allocated in
new_nbp() need be freed, or it will be leaked.
Fixes: 1080ab95e3c7 ("net: bridge: add support for IGMP/MLD stats and export them via netlink") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Link: https://lore.kernel.org/r/20210809132023.978546-1-yangyingliang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Ignore fdb flags when adding port extern learn entries and always set
BR_FDB_LOCAL flag when adding bridge extern learn entries. This is
closest to the behaviour we had before and avoids breaking any use cases
which were allowed.
This patch fixes iproute2 calls which assume NUD_PERMANENT and were
allowed before, example:
$ bridge fdb add 00:11:22:33:44:55 dev swp1 extern_learn
Extern learn entries are allowed to roam, but do not expire, so static
or dynamic flags make no sense for them.
Also add a comment for future reference.
Fixes: eb100e0e24a2 ("net: bridge: allow to add externally learned entries from user-space") Fixes: 0541a6293298 ("net: bridge: validate the NUD_PERMANENT bit when adding an extern_learn FDB entry") Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20210810110010.43859-1-razor@blackwall.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently it is possible to add broken extern_learn FDB entries to the
bridge in two ways:
1. Entries pointing towards the bridge device that are not local/permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static
2. Entries pointing towards the bridge device or towards a port that
are marked as local/permanent, however the bridge does not process the
'permanent' bit in any way, therefore they are recorded as though they
aren't permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent
Since commit 52e4bec15546 ("net: bridge: switchdev: treat local FDBs the
same as entries towards the bridge"), these incorrect FDB entries can
even trigger NULL pointer dereferences inside the kernel.
This is because that commit made the assumption that all FDB entries
that are not local/permanent have a valid destination port. For context,
local / permanent FDB entries either have fdb->dst == NULL, and these
point towards the bridge device and are therefore local and not to be
used for forwarding, or have fdb->dst == a net_bridge_port structure
(but are to be treated in the same way, i.e. not for forwarding).
That assumption _is_ correct as long as things are working correctly in
the bridge driver, i.e. we cannot logically have fdb->dst == NULL under
any circumstance for FDB entries that are not local. However, the
extern_learn code path where FDB entries are managed by a user space
controller show that it is possible for the bridge kernel driver to
misinterpret the NUD flags of an entry transmitted by user space, and
end up having fdb->dst == NULL while not being a local entry. This is
invalid and should be rejected.
Before, the two commands listed above both crashed the kernel in this
check from br_switchdev_fdb_notify:
After this patch, the invalid entry added by the first command is
rejected:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static; ip link del br0
Error: bridge: FDB entry towards bridge must be permanent.
and the valid entry added by the second command is properly treated as a
local address and does not crash br_switchdev_fdb_notify anymore:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent; ip link del br0
Fixes: eb100e0e24a2 ("net: bridge: allow to add externally learned entries from user-space") Reported-by: syzbot+9ba1174359adba5a5b7c@syzkaller.appspotmail.com Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Link: https://lore.kernel.org/r/20210801231730.7493-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 58c59ef9e930 ("net: dsa: lantiq: Add Forwarding Database access") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: ab335349b852 ("net: dsa: lan9303: Add port_fast_age and port_fdb_dump methods") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>