syzbot reports a divide-by-zero off the NBD_SET_BLKSIZE ioctl.
We need proper validation of the input here. Not just if it's
zero, but also if the value is a power-of-2 and in a valid
range. Add that.
Cc: stable@vger.kernel.org Reported-by: syzbot <syzbot+25dbecbec1e62c6b0dd4@syzkaller.appspotmail.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A recent change added some MDS processing in the lpfc_drain_txq routine
that relies on the fcp_wq being allocated. For nvmet operation the fcp_wq
is not allocated because it can only be an nvme-target. When the original
MDS support was added LS_MDS_LOOPBACK was defined wrong, (0x16) it should
have been 0x10 (decimal value used for hex setting). This incorrect value
allowed MDS_LOOPBACK to be set simultaneously with LS_NPIV_FAB_SUPPORTED,
causing the driver to crash when it accesses the non-existent fcp_wq.
Correct the bad value setting for LS_MDS_LOOPBACK.
Fixes: ae9e28f36a6c ("lpfc: Add MDS Diagnostic support.") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Tested-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
DNV's iTCO is slightly different with SMBCTRL sitting at a different
offset when compared to all other devices. Let's fix so that we can
properly use iTCO watchdog.
Fixes: 84d7f2ebd70d ("i2c: i801: Add support for Intel DNV") Cc: <stable@vger.kernel.org> # v4.4+ Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Disable interrupts while configuring the transfer and enable them back.
We have below as the programming sequence
1. start and slave address
2. byte count and stop
In some customer platform there was a lot of interrupts between 1 and 2
and after slave address (around 7 clock cyles) if 2 is not executed
then the transaction is nacked.
To fix this case make the 2 writes atomic.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[wsa: added a newline for better readability] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Loops per jiffy is calculated by multiplying tsc_khz with 1e3 and then
dividing it by HZ.
Both tsc_khz and the temporary variable holding the multiplication result
are of type unsigned long, so on 32bit the result is truncated to the lower
32bit.
Use u64 as type for the temporary variable and cast tsc_khz to it before
multiplying.
[ tglx: Massaged changelog and removed pointless braces ]
[ tglx: Backport to stable. Due to massive code changes is the upstream
commit not applicable anymore. The issue has gone unnoticed in
kernels pre 4.19 because the bogus LPJ value gets fixed up in a
later stage of early boot, but it still might cause subtle and hard
to debug issues between these two points. ]
Fixes: cf7a63ef4e02 ("x86/tsc: Calibrate tsc only once") Signed-off-by: Chuanhua Lei <chuanhua.lei@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: yixin.zhu@linux.intel.com Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Len Brown <len.brown@intel.com> Cc: Pavel Tatashin <pasha.tatashin@microsoft.com> Cc: Rajvi Jingar <rajvi.jingar@intel.com> Cc: Dou Liyang <douly.fnst@cn.fujitsu.com> Link: https://lkml.kernel.org/r/1536228203-18701-1-git-send-email-chuanhua.lei@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Since Haswell we have no color range indication either in the pipe or
port registers for DP. Instead, there's a separate register for setting
the DP Main Stream Attributes (MSA) directly. The MSA register
definition makes no references to colorimetry, just a vague reference to
the DP spec. The connection to the color range was lost.
Apparently we've failed to set the proper MSA bit for limited, or CEA,
range ever since the first DDI platforms. We've started setting other
MSA parameters since commit dae847991a43 ("drm/i915: add
intel_ddi_set_pipe_settings").
Without the crucial bit of information, the DP sink has no way of
knowing the source is actually transmitting limited range RGB, leading
to "washed out" colors. With the colorimetry information, compliant
sinks should be able to handle the limited range properly. Native
(i.e. non-LSPCON) HDMI was not affected because we do pass the color
range via AVI infoframes.
Though not the root cause, the problem was made worse for DDI platforms
with commit 55bc60db5988 ("drm/i915: Add "Automatic" mode for the
"Broadcast RGB" property"), which selects limited range RGB
automatically based on the mode, as per the DP, HDMI and CEA specs.
After all these years, the fix boils down to flipping one bit.
[Per testing reports, this fixes DP sinks, but not the LSPCON. My
educated guess is that the LSPCON fails to turn the CEA range MSA into
AVI infoframes for HDMI.]
Reported-by: Michał Kopeć <mkopec12@gmail.com> Reported-by: N. W. <nw9165-3201@yahoo.com> Reported-by: Nicholas Stommel <nicholas.stommel@gmail.com> Reported-by: Tom Yan <tom.ty89@gmail.com> Tested-by: Nicholas Stommel <nicholas.stommel@gmail.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=100023
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107476
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94921 Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: <stable@vger.kernel.org> # v3.9+ Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180814060001.18224-1-jani.nikula@intel.com
(cherry picked from commit dc5977da99ea28094b8fa4e9bacbd29bedc41de5) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
That's the PID of the creator of the file (usually the X server) and not
the end user of the file.
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Christian König <christian.koenig@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> CC: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[why]
We are disabling clock source while other pipes are still using
it, because we don't verify the number of pipes that share it.
[how]
- Adding a function in resources to return the number of pipes
sharing the clock source.
- Checking that no one is sharing the clock source before disabling
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[why]
Older ASICs require both phys_id and connector_id
to execute bios command table. If we are not passing the
right connector_id - it can lead to a black screen.
[how]
Set connector_obj_id when executing vbios command table
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[Why]
The DRM mode's HDMI picture aspect ratio field was never saved in
dc_stream's timing struct. This causes us to mistake a new stream to
have the same timings as the old, even though the user has requested a
different aspect ratio.
[How]
Save DRM's aspect ratio field within dc_stream's timing struct.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=107153 Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com> Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[why]
When programming tonga's connector's backend we didn't take
in account that HDMI's colour depth might be more than 8bpc
therefore we need to add a switch statement that would adjust
the pixel clock accordingly.
[how]
Add a switch statement updating clock by its appropriate
coefficient.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[why]
Prevent clock source sharing between HDMI and DP connectors.
DP shouldn't be sharing its ref clock with phy clock,
which caused an issue of older ASICS booting up with multiple
diplays plugged in.
[how]
Add an extra check that would prevent HDMI and DP sharing clk.
We broke the LVDS notifier resume thing in (presumably) commit e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.") as
we no longer duplicate the current state in the LVDS notifier and
thus we never resume it properly either.
Instead of trying to fix it again let's just kill off the lid
notifier entirely. None of the machines tested thus far have
apparently needed it. Originally the lid notifier was added to
work around cases where the VBIOS was clobbering some of the
hardware state behind the driver's back, mostly on Thinkpads.
We now have a few report of Thinkpads working just fine without
the notifier. So maybe it was misdiagnosed originally, or
something else has changed (ACPI video stuff perhaps?).
If we do end up finding a machine where the VBIOS is still causing
problems I would suggest that we first try setting various bits in
the VBIOS scratch registers. There are several to choose from that
may instruct the VBIOS to steer clear.
With the notifier gone we'll also stop looking at the panel status
in ->detect().
The C programming language does not allow to use preprocessor statements
inside macro arguments (pr_info() is defined as a macro). Hence rework
the pr_info() statement in btrfs_print_mod_info() such that it becomes
compliant. This patch allows tools like sparse to analyze the BTRFS
source code.
Fixes: 62e855771dac ("btrfs: convert printk(KERN_* to use pr_* calls") Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Prepartory work to fix race between mount and device scan.
The callers will have to manage the critical section, eg. mount wants to
scan and then call btrfs_open_devices without the ioctl scan walking in
and modifying the fs devices in the meantime.
Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit f8f84b2dfda5 ("btrfs: index check-integrity state hash by a dev_t")
changed how btrfsic indexes device state.
Now we need to access device->bdev->bd_dev, while for degraded mount
it's completely possible to have device->bdev as NULL, thus it will
trigger a NULL pointer dereference at mount time.
Fix it by checking if the device is degraded before accessing
device->bdev->bd_dev.
There are a lot of other places accessing device->bdev->bd_dev, however
the other call sites have either checked device->bdev, or the
device->bdev is passed from btrfsic_map_block(), so it won't cause harm.
Fixes: f8f84b2dfda5 ("btrfs: index check-integrity state hash by a dev_t") Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[Why]
If there is no program explicitly setting the backlight
brightness (for example, during a minimal install of linux), the
hardware defaults to maximum brightness but the backlight_device
defaults to 0 value. Thus, settings displays the wrong brightness
value.
[How]
When creating the backlight device, set brightness to max
Signed-off-by: David Francis <David.Francis@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If the resource requested by d_alloc_name is not added to the linked
list through d_add, then dput needs to be called to release the
subsequent abnormal branch to avoid resource leakage.
Add missing dput to selinuxfs.c
Signed-off-by: nixiaoming <nixiaoming@huawei.com>
[PM: tweak the subject line] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently, we count the hctx as active after allocate driver tag
successfully. If a previously inactive hctx try to get tag first
time, it may fails and need to wait. However, due to the stale tag
->active_queues, the other shared-tags users are still able to
occupy all driver tags while there is someone waiting for tag.
Consequently, even if the previously inactive hctx is waked up, it
still may not be able to get a tag and could be starved.
To fix it, we count the hctx as active before try to allocate driver
tag, then when it is waiting the tag, the other shared-tag users
will reserve budget for it.
Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If you use a 64-bit compiler to build a 32-bit kernel then you'll get an
error when building the vDSO due to a library mismatch. The happens
because the relevant "-march" argument isn't supplied to the GCC run
that generates one of the vDSO intermediate files.
I'm not actually sure what the right thing to do here is as I'm not
particularly familiar with the kernel build system. I poked the
documentation and it appears that KCFLAGS is the correct thing to do
(it's suggested that should be used when building modules), but we set
KBUILD_CFLAGS in arch/riscv/Makefile.
This does at least fix the build error.
Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Palmer Dabbelt <palmer@sifive.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If coccicheck fails, it should return an error code distinct from zero
to signal about an internal problem. Current code instead of exiting with
the tool's error code returns the error code of 'echo "coccicheck failed"'
which is almost always equals to zero, thus failing the original intention
of alerting about a problem. This patch fixes the code.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <efremov@linux.com> Acked-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In commit 27d868b5e6cf ("PCI: Set MPS to match upstream bridge"), we made
sure every device's MPS setting matches its upstream bridge, making it more
likely that a hot-added device will work in a system with an optimized MPS
configuration.
Recently I've started encountering systems where the endpoint device's MPSS
capability is less than its Root Port's current MPS value, thus the
endpoint is not capable of matching its upstream bridge's MPS setting (see:
bugzilla via "Link:" below). This leaves the system vulnerable - the
upstream Root Port could respond with larger TLPs than the device can
handle, and the device will consider them to be 'Malformed'.
One could use the "pci=pcie_bus_safe" kernel parameter to work around the
issue, but that forces a user to supply a kernel parameter to get the
system to function reliably and may end up limiting MPS settings of other
unrelated, sub-topologies which could benefit from maintaining their larger
values.
Augment Keith's approach to include tuning down a Root Port's MPS setting
when its hot-added endpoint device is not capable of matching it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200527 Signed-off-by: Myron Stowe <myron.stowe@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Jon Mason <jdmason@kudzu.us> Cc: Keith Busch <keith.busch@intel.com> Cc: Sinan Kaya <okaya@kernel.org> Cc: Dongdong Liu <liudongdong3@huawei.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The value coming from acpi_hw_read() should not be used if it
returns an error code, so check the status returned by it before
using that value in two places in acpi_hw_register_read().
Reported-by: Mark Gross <mark.gross@intel.com> Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
[ rjw: Changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
eacd86ca3b03 ("net/netfilter/x_tables.c: use kvmalloc()
in xt_alloc_table_info()") has unintentionally fortified
xt_alloc_table_info allocation when __GFP_RETRY has been dropped from
the vmalloc fallback. Later on there was a syzbot report that this
can lead to OOM killer invocations when tables are too large and 0537250fdc6c ("netfilter: x_tables: make allocation less aggressive")
has been merged to restore the original behavior. Georgi Nikolov however
noticed that he is not able to install his iptables anymore so this can
be seen as a regression.
The primary argument for 0537250fdc6c was that this allocation path
shouldn't really trigger the OOM killer and kill innocent tasks. On the
other hand the interface requires root and as such should allow what the
admin asks for. Root inside a namespaces makes this more complicated
because those might be not trusted in general. If they are not then such
namespaces should be restricted anyway. Therefore drop the __GFP_NORETRY
and replace it by __GFP_ACCOUNT to enfore memcg constrains on it.
Fixes: 0537250fdc6c ("netfilter: x_tables: make allocation less aggressive") Reported-by: Georgi Nikolov <gnikolov@icdsoft.com> Suggested-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
I found that in BPF sockmap programs once we either delete a socket
from the map or we updated a map slot and the old socket was purged
from the map that these socket can never get reattached into a map
even though their related psock has been dropped entirely at that
point.
Reason is that tcp_cleanup_ulp() leaves the old icsk->icsk_ulp_ops
intact, so that on the next tcp_set_ulp_id() the kernel returns an
-EEXIST thinking there is still some active ULP attached.
BPF sockmap is the only one that has this issue as the other user,
kTLS, only calls tcp_cleanup_ulp() from tcp_v4_destroy_sock() whereas
sockmap semantics allow dropping the socket from the map with all
related psock state being cleaned up.
Fixes: 1aa12bdf1bfb ("bpf: sockmap, add sock close() hook to remove socks") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
We should return error pointers in this function. Returning NULL
results in a NULL dereference in the caller.
Fixes: 73688d1ed0b8 ("apparmor: refactor prepare_ns() and make usable from different views") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In flush_work(), we need to create a lockdep dependency so that
the following scenario is appropriately tagged as a problem:
work_function()
{
mutex_lock(&mutex);
...
}
other_function()
{
mutex_lock(&mutex);
flush_work(&work); // or cancel_work_sync(&work);
}
This is a problem since the work might be running and be blocked
on trying to acquire the mutex.
Similarly, in flush_workqueue().
These were removed after cross-release partially caught these
problems, but now cross-release was reverted anyway. IMHO the
removal was erroneous anyway though, since lockdep should be
able to catch potential problems, not just actual ones, and
cross-release would only have caught the problem when actually
invoking wait_for_completion().
Fixes: fd1a5b04dfb8 ("workqueue: Remove now redundant lock acquisitions wrt. workqueue flushes") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In cancel_work_sync(), we can only have one of two cases, even
with an ordered workqueue:
* the work isn't running, just cancelled before it started
* the work is running, but then nothing else can be on the
workqueue before it
Thus, we need to skip the lockdep workqueue dependency handling,
otherwise we get false positive reports from lockdep saying that
we have a potential deadlock when the workqueue also has other
work items with locking, e.g.
This because ip6n->tnls_wc[0] point to fallback device in default, but
in non-default namespace, ip6n->tnls_wc[0] will be NULL, so add the NULL
check comparatively.
Fixes: e2948e5af8ee ("ip6_vti: fix creating fallback tunnel device for vti6") Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In function tipc_dest_push, the 32bit variables 'node' and 'port'
are stored separately in uppper and lower part of 64bit 'value'.
Then this value is assigned to dst->value which is a union like:
union
{
struct {
u32 port;
u32 node;
};
u64 value;
}
This works on little-endian machines like x86 but fails on big-endian
machines.
The fix remove the 'value' stack parameter and even the 'value'
member of the union in tipc_dest, assign the 'node' and 'port' member
directly with the input parameter to avoid the endian issue.
Fixes: a80ae5306a73 ("tipc: improve destination linked list") Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If there is a mismatch in the I/D min line size, we must
always use the system wide safe value both in applications
and in the kernel, while performing cache operations. However,
we have been checking more bits than just the min line sizes,
which triggers false negatives. We may need to trap the user
accesses in such cases, but not necessarily patch the kernel.
This patch fixes the check to do the right thing as advertised.
A new capability will be added to check mismatches in other
fields and ensure we trap the CTR accesses.
Fixes: be68a8aaf925 ("arm64: cpufeature: Fix CTR_EL0 field definitions") Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Add missing break statement in order to prevent the code from falling
through to the default case.
Addresses-Coverity-ID: 115050 ("Missing break in switch") Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
[Gustavo: Backported to 3.16..4.18 - Remove code comment removal] Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Without including psci.h and arm-smccc.h, we now get a build failure in
some configurations:
arch/arm64/kernel/cpu_errata.c: In function 'arm64_update_smccc_conduit':
arch/arm64/kernel/cpu_errata.c:278:10: error: 'psci_ops' undeclared (first use in this function); did you mean 'sysfs_ops'?
arch/arm64/kernel/cpu_errata.c: In function 'arm64_set_ssbd_mitigation':
arch/arm64/kernel/cpu_errata.c:311:3: error: implicit declaration of function 'arm_smccc_1_1_hvc' [-Werror=implicit-function-declaration]
arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_WORKAROUND_2, state, NULL);
Always set the 5 upper-most supported physical address bits to 1 for SPTEs
that are marked as non-present or reserved, to make them unusable for
L1TF attacks from the guest. Currently, this just applies to MMIO SPTEs.
(We do not need to mark PTEs that are completely 0 as physical page 0
is already reserved.)
This allows mitigation of L1TF without disabling hyper-threading by using
shadow paging mode instead of EPT.
Signed-off-by: Junaid Shahid <junaids@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When $DEPMOD is not found, only print a warning instead of exiting
with an error message and error status:
Warning: 'make modules_install' requires /sbin/depmod. Please install it.
This is probably in the kmod package.
Change the Error to a Warning because "not all build hosts for cross
compiling Linux are Linux systems and are able to provide a working
port of depmod, especially at the file patch /sbin/depmod."
I.e., "make modules_install" may be used to copy/install the
loadable modules files to a target directory on a build system and
then transferred to an embedded device where /sbin/depmod is run
instead of it being run on the build system.
Fixes: 934193a654c1 ("kbuild: verify that $DEPMOD is installed") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: H. Nikolaus Schaller <hns@goldelico.com> Cc: stable@vger.kernel.org Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Cc: Lucas De Marchi <lucas.de.marchi@gmail.com> Cc: Michal Marek <michal.lkml@markovi.net> Cc: Jessica Yu <jeyu@kernel.org> Cc: Chih-Wei Huang <cwhuang@linux.org.tw> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
100 ms is not enough time for the LSPCON adapter on Intel NUC devices to
settle. This causes dropped display modes at boot or screen reconfiguration.
Empirical testing can reproduce the error up to a timeout of 190 ms. Basic
boot and stress testing at 200 ms has not (yet) failed.
Increase timeout to 400 ms to get some margin of error.
Changes from v1:
The initial suggestion of 1000 ms was lowered due to concerns about delaying
valid timeout cases.
Update patch metadata.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107503
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1570392 Fixes: 357c0ae9198a ("drm/i915/lspcon: Wait for expected LSPCON mode to settle") Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: <stable@vger.kernel.org> # v4.11+ Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Fredrik Schön <fredrik.schon@gmail.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180817200728.8154-1-fredrik.schon@gmail.com
(cherry picked from commit 59f1c8ab30d6f9042562949f42cbd3f3cf69de94) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Fredrik Schön <fredrik.schon@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In some cases 32-bit PAE PV guests still write PTEs directly instead of
using hypercalls. This is especially bad when clearing a PTE as this is
done via 32-bit writes which will produce intermediate L1TF attackable
PTEs.
Change the code to use hypercalls instead.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Using only 32-bit writes for the pte will result in an intermediate
L1TF vulnerable PTE. When running as a Xen PV guest this will at once
switch the guest to shadow mode resulting in a loss of performance.
Use arch_atomic64_xchg() instead which will perform the requested
operation atomically with all 64 bits.
The main number should be the latency, as there is no tight loop around
native_ptep_get_and_clear().
"lock cmpxchg8b" has a latency of 20 cycles, while "lock xchg" (with a
memory operand) isn't mentioned in that document. "lock xadd" (with xadd
having 3 cycles less latency than xchg) has a latency of 11, so we can
assume a latency of 14 for "lock xchg".
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jan Beulich <jbeulich@suse.com> Tested-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
[ Atomic operations gained an arch_ prefix in 8bf705d13039
("locking/atomic/x86: Switch atomic.h to use atomic-instrumented.h") so
s/arch_atomic64_xchg/atomic64_xchg/ for backport.] Signed-off-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should
be called only once during the life cycle of the driver. However,
as dwc3_core_init() is called during system suspend/resume it will
result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init()
which is wrong.
Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup()
into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that
dwc3_core_ulpi_init() is called only once from dwc3_core_init().
Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from
dwc3_core_init().
Fixes: 541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys") Fixes: f54edb539c11 ("usb: dwc3: core: initialize ULPI before trying to get the PHY") Cc: linux-stable <stable@vger.kernel.org> # >= v4.13 Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This mouse keep disconnecting in runleve 3 like below, add it needs the
quirk to mute the anoying messages.
[ 111.230555] usb 2-2: USB disconnect, device number 6
[ 112.718156] usb 2-2: new low-speed USB device number 7 using xhci_hcd
[ 112.941594] usb 2-2: New USB device found, idVendor=03f0, idProduct=094a
[ 112.984866] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 113.027731] usb 2-2: Product: HP USB Optical Mouse
[ 113.069977] usb 2-2: Manufacturer: PixArt
[ 113.113500] input: PixArt HP USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.0/0003:03F0:094A.0002/input/input14
[ 113.156787] hid-generic 0003:03F0:094A.0002: input: USB HID v1.11 Mouse [PixArt HP USB Optical Mouse] on usb-0000:00:14.0-2/input0
[ 173.262642] usb 2-2: USB disconnect, device number 7
[ 174.750244] usb 2-2: new low-speed USB device number 8 using xhci_hcd
[ 174.935740] usb 2-2: New USB device found, idVendor=03f0, idProduct=094a
[ 174.990435] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 175.014984] usb 2-2: Product: HP USB Optical Mouse
[ 175.037886] usb 2-2: Manufacturer: PixArt
[ 175.061794] input: PixArt HP USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.0/0003:03F0:094A.0003/input/input15
[ 175.084946] hid-generic 0003:03F0:094A.0003: input: USB HID v1.11 Mouse [PixArt HP USB Optical Mouse] on usb-0000:00:14.0-2/input0
Signed-off-by: Dave Young <dyoung@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If devm_memremap_pages() detects a collision while adding entries
to the radix-tree, we call pgmap_radix_release(). Unfortunately,
the function removes *all* entries for the range -- including the
entries that caused the collision in the first place.
Modify pgmap_radix_release() to take an additional argument to
indicate where to stop, so that only newly added entries are removed
from the tree.
Cc: <stable@vger.kernel.org> Fixes: 9476df7d80df ("mm: introduce find_dev_pagemap()") Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While debugging an issue debugobject tracking warned about an annotation
issue of an object on stack. It turned out that the issue was due to the
object in concern being on a different stack which was due to another
issue.
Thomas suggested to print the pointers and the location of the stack for
the currently running task. This helped to figure out that the object was
on the wrong stack.
As this is general useful information for debugging similar issues, make
the error message more informative by printing the pointers.
[ tglx: Massaged changelog ]
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Waiman Long <longman@redhat.com> Acked-by: Yang Shi <yang.shi@linux.alibaba.com> Cc: kernel-team@android.com Cc: Arnd Bergmann <arnd@arndb.de> Cc: astrachan@google.com Link: https://lkml.kernel.org/r/20180723212531.202328-1-joel@joelfernandes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The LPE audio is a child device of i915, it is powered up and down
alongside the igfx and presents no independent runtime interface. This
aptly fulfils the description of a "No-Callback" Device, so mark it
thus.
Fixes: 183c00350ccd ("drm/i915: Fix runtime PM for LPE audio")
Testcase: igt/pm_rpm/basic-pci-d3-state
Testcase: igt/pm_rpm/basic-rte Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Takashi Iwai <tiwai@suse.de> Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: stable@vger.kernel.org Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180802140416.6062-1-chris@chris-wilson.co.uk
(cherry picked from commit 46e831abe864a6b59fa3de253a681c0f2ee1bf2f) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A number of the Rockchip-specific drivers (IOMMU, display controllers)
are now assuming that CONFIG_PM is set, and may completely misbehave
if that's not the case.
Since there is hardly any reason for this configuration option not
to be selected anyway, let's require it (in the same way Tegra already
does).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
A number of the Rockchip-specific drivers (IOMMU, display controllers)
are now assuming that CONFIG_PM is set, and may completely misbehave
if that's not the case.
Since there is hardly any reason for this configuration option not
to be selected anyway, let's require it (in the same way Tegra already
does).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BTRFS critical (device vda2): unable to find logical 8820195328 length 16384
BTRFS: error (device vda2) in btrfs_finish_ordered_io:3023: errno=-5 IO failure
BTRFS info (device vda2): forced readonly
BTRFS error (device vda2): pending csums is 2887680
[CAUSE]
It's caused by race with block group auto removal:
- There is a meta block group X, which has only one tree block
The tree block belongs to fs tree 257.
- In current transaction, some operation modified fs tree 257
The tree block gets COWed, so the block group X is empty, and marked
as unused, queued to be deleted.
- Some workload (like fsync) wakes up cleaner_kthread()
Which will call btrfs_delete_unused_bgs() to remove unused block
groups.
So block group X along its chunk map get removed.
- Some delalloc work finished for fs tree 257
Quota needs to get the original reference of the extent, which will
read tree blocks of commit root of 257.
Then since the chunk map gets removed, the above warning gets
triggered.
[FIX]
Just let btrfs_delete_unused_bgs() skip block group which still has
pinned bytes.
However there is a minor side effect: currently we only queue empty
blocks at update_block_group(), and such empty block group with pinned
bytes won't go through update_block_group() again, such block group
won't be removed, until it gets new extent allocated and removed.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Invalid reloc tree can cause kernel NULL pointer dereference when btrfs
does some cleanup of the reloc roots.
It turns out that fs_info::reloc_ctl can be NULL in
btrfs_recover_relocation() as we allocate relocation control after all
reloc roots have been verified.
So when we hit: note, we haven't called set_reloc_control() thus
fs_info::reloc_ctl is still NULL.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199833 Reported-by: Xu Wen <wen.xu@gatech.edu> Signed-off-by: Qu Wenruo <wqu@suse.com> Tested-by: Gu Jinxiang <gujx@cn.fujitsu.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
on-disk devs stats value is updated in btrfs_run_dev_stats(),
which is called during commit transaction, if device->dev_stats_ccnt
is not zero.
Since current replace operation does not touch dev_stats_ccnt,
on-disk dev stats value is not updated. Therefore "btrfs device stats"
may return old device's value after umount/mount
(Example: See "btrfs ins dump-t -t DEV $DEV" after btrfs/100 finish).
Fix this by just incrementing dev_stats_ccnt in
btrfs_dev_replace_finishing() when replace is succeeded and this will
update the values.
Signed-off-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It's entirely possible that a crafted btrfs image contains overlapping
chunks.
Although we can't detect such problem by tree-checker, it's not a
catastrophic problem, current extent map can already detect such problem
and return -EEXIST.
We just only need to exit gracefully and fail the mount.
Reported-by: Xu Wen <wen.xu@gatech.edu> Link: https://bugzilla.kernel.org/show_bug.cgi?id=200409 Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Using 'struct loaded_vmcs*' to track whether the CPU registers
contain host or guest state kills two birds with one stone.
1. The (effective) boolean host_state.loaded is poorly named.
It does not track whether or not host state is loaded into
the CPU registers (which most readers would expect), but
rather tracks if host state has been saved AND guest state
is loaded.
2. Using a loaded_vmcs pointer provides a more robust framework
for the optimized guest/host state switching, especially when
consideration per-VMCS enhancements. To that end, WARN_ONCE
if we try to switch to host state with a different VMCS than
was last used to save host state.
Resolve an occurrence of the new WARN by setting loaded_vmcs after
the call to vmx_vcpu_put() in vmx_switch_vmcs().
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
PWM2 is commonly used to control voltage of PWM regulator of VDD_LOG in
RK3399. On the Firefly-RK3399 board, PWM2 outputs 40 KHz square wave
from power on and the VDD_LOG is about 0.9V. When the kernel boots
normally into the system, the PWM2 keeps outputing PWM signal.
But the kernel hangs randomly after "Starting kernel ..." line on that
board. When it happens, PWM2 outputs high level which causes VDD_LOG
drops to 0.4V below the normal operating voltage.
By adding "pclk_rkpwm_pmu" to the rk3399_pmucru_critical_clocks array,
PWM clock is ensured to be prepared at startup and the PWM2 output is
normal. After repeated tests, the early boot hang is gone.
This patch works on both Firefly-RK3399 and ROC-RK3399-PC boards.
Signed-off-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The global mce data buffer that used to copy rtas error log is of 2048
(RTAS_ERROR_LOG_MAX) bytes in size. Before the copy we read
extended_log_length from rtas error log header, then use max of
extended_log_length and RTAS_ERROR_LOG_MAX as a size of data to be copied.
Ideally the platform (phyp) will never send extended error log with
size > 2048. But if that happens, then we have a risk of buffer overrun
and corruption. Fix this by using min_t instead.
Fixes: d368514c3097 ("powerpc: Fix corruption when grabbing FWNMI data") Reported-by: Michal Suchanek <msuchanek@suse.com> Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Because rfi_flush_fallback runs immediately before the return to
userspace it currently runs with the user r1 (stack pointer). This
means if we oops in there we will report a bad kernel stack pointer in
the exception entry path, eg:
Although the NIP tells us where we were, and the TRAP number tells us
what happened, it would still be nicer if we could report the actual
exception rather than barfing about the stack pointer.
We an do that fairly simply by loading the kernel stack pointer on
entry and restoring the user value before returning. That way we see a
regular oops such as:
Note this shouldn't make the kernel stack pointer vulnerable to a
meltdown attack, because it should be flushed from the cache before we
return to userspace. The user r1 value will be in the cache, because
we load it in the return path, but that is harmless.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix build errors and warnings in t1042rdb_diu.c by adding header files
and MODULE_LICENSE().
../arch/powerpc/platforms/85xx/t1042rdb_diu.c:152:1: warning: data definition has no type or storage class
early_initcall(t1042rdb_diu_init);
../arch/powerpc/platforms/85xx/t1042rdb_diu.c:152:1: error: type defaults to 'int' in declaration of 'early_initcall' [-Werror=implicit-int]
../arch/powerpc/platforms/85xx/t1042rdb_diu.c:152:1: warning: parameter names (without types) in function declaration
and
WARNING: modpost: missing MODULE_LICENSE() in arch/powerpc/platforms/85xx/t1042rdb_diu.o
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Scott Wood <oss@buserror.net> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
For SMB2/SMB3 the number of requests sent was not displayed
in /proc/fs/cifs/Stats unless CONFIG_CIFS_STATS2 was
enabled (only number of failed requests displayed). As
with earlier dialects, we should be displaying these
counters if CONFIG_CIFS_STATS is enabled. They
are important for debugging.
e.g. when you cat /proc/fs/cifs/Stats (before the patch)
Resources in use
CIFS Session: 1
Share (unique mount targets): 2
SMB Request/Response Buffer: 1 Pool size: 5
SMB Small Req/Resp Buffer: 1 Pool size: 30
Operations (MIDs): 0
0 session 0 share reconnects
Total vfs operations: 690 maximum at one time: 2
1) \\localhost\test
SMBs: 975
Negotiates: 0 sent 0 failed
SessionSetups: 0 sent 0 failed
Logoffs: 0 sent 0 failed
TreeConnects: 0 sent 0 failed
TreeDisconnects: 0 sent 0 failed
Creates: 0 sent 2 failed Closes: 0 sent 0 failed
Flushes: 0 sent 0 failed
Reads: 0 sent 0 failed
Writes: 0 sent 0 failed
Locks: 0 sent 0 failed
IOCTLs: 0 sent 1 failed
Cancels: 0 sent 0 failed
Echos: 0 sent 0 failed
QueryDirectories: 0 sent 63 failed
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
echo 0 > /proc/fs/cifs/Stats is supposed to reset the stats
but there were four (see example below) that were not reset
(bytes read and witten, total vfs ops and max ops
at one time).
...
0 session 0 share reconnects
Total vfs operations: 100 maximum at one time: 2
This patch does not change any functionality but avoids that gcc
reports the following warnings when building with W=1:
block/cfq-iosched.c: In function ?cfq_back_seek_max_store?:
block/cfq-iosched.c:4741:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4756:1: note: in expansion of macro ?STORE_FUNCTION?
STORE_FUNCTION(cfq_back_seek_max_store, &cfqd->cfq_back_max, 0, UINT_MAX, 0);
^~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_slice_idle_store?:
block/cfq-iosched.c:4741:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4759:1: note: in expansion of macro ?STORE_FUNCTION?
STORE_FUNCTION(cfq_slice_idle_store, &cfqd->cfq_slice_idle, 0, UINT_MAX, 1);
^~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_group_idle_store?:
block/cfq-iosched.c:4741:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4760:1: note: in expansion of macro ?STORE_FUNCTION?
STORE_FUNCTION(cfq_group_idle_store, &cfqd->cfq_group_idle, 0, UINT_MAX, 1);
^~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_low_latency_store?:
block/cfq-iosched.c:4741:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4765:1: note: in expansion of macro ?STORE_FUNCTION?
STORE_FUNCTION(cfq_low_latency_store, &cfqd->cfq_latency, 0, 1, 0);
^~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_slice_idle_us_store?:
block/cfq-iosched.c:4775:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4782:1: note: in expansion of macro ?USEC_STORE_FUNCTION?
USEC_STORE_FUNCTION(cfq_slice_idle_us_store, &cfqd->cfq_slice_idle, 0, UINT_MAX);
^~~~~~~~~~~~~~~~~~~
block/cfq-iosched.c: In function ?cfq_group_idle_us_store?:
block/cfq-iosched.c:4775:13: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
if (__data < (MIN)) \
^
block/cfq-iosched.c:4783:1: note: in expansion of macro ?USEC_STORE_FUNCTION?
USEC_STORE_FUNCTION(cfq_group_idle_us_store, &cfqd->cfq_group_idle, 0, UINT_MAX);
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
There are some powerpc selftests, as tm/tm-unavailable, that run for a long
period (>120 seconds), and if it is interrupted, as pressing CRTL-C
(SIGINT), the foreground process (harness) dies but the child process and
threads continue to execute (with PPID = 1 now) in background.
In this case, you'd think the whole test exited, but there are remaining
threads and processes being executed in background. Sometimes these
zombies processes are doing annoying things, as consuming the whole CPU or
dumping things to STDOUT.
This patch fixes this problem by attaching an empty signal handler to
SIGINT in the harness process. This handler will interrupt (EINTR) the
parent process waitpid() call, letting the code to follow through the
normal flow, which will kill all the processes in the child process group.
This patch also fixes a typo.
Signed-off-by: Breno Leitao <leitao@debian.org> Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The base address used for DMA operations on the second-level table
did incorrectly include the offset for the table entry. The offset
was then added again which lead to incorrect behavior.
Operations on the L1 table are not affected.
The calculation of the base address is changed to point to the
beginning of the L2 table.
Fixes: bfee0cf0ee1d ("iommu/omap: Use DMA-API for performing cache flushes") Acked-by: Suman Anna <s-anna@ti.com> Signed-off-by: Ralf Goebel <ralf.goebel@imago-technologies.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver expects to find the device id in rt5677_of_match.data, however
it is currently assigned to rt5677_of_match.type. Fix this.
The problem was found with the help of clang:
sound/soc/codecs/rt5677.c:5010:36: warning: expression which evaluates to
zero treated as a null pointer constant of type 'const void *'
[-Wnon-literal-null-conversion]
{ .compatible = "realtek,rt5677", RT5677 },
^~~~~~
Fixes: ddc9e69b9dc2 ("ASoC: rt5677: Hide platform data in the module sources") Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Guenter Roeck <groeck@chromium.org> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The PFI subdevice flags indicate that the subdevice is readable and
writeable, but that is only true for the supported "M-series" boards,
not the older "E-series" boards. Only set the SDF_READABLE and
SDF_WRITABLE subdevice flags for the M-series boards. These two flags
are mainly for informational purposes.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix this by calling cond_resched() after run_complete_job()'s callout to
the dm_kcopyd_notify_fn (which is dm-snap.c:copy_callback in the above
trace).
Signed-off-by: John Pittman <jpittman@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
pcie->realio.end should be the address of last byte of the area,
therefore using resource_size() of another resource is not correct, we
must substract 1 to get the address of the last byte.
Fixes: 11be65472a427 ("PCI: mvebu: Adapt to the new device tree layout") Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The current balloon code tries to calculate a delta factor for the
balloon target when running in HVM mode in order to account for memory
used by the firmware.
This workaround for memory accounting doesn't work properly on a PVH
Dom0, that has a static-max value different from the target value even
at startup. Note that this is not a problem for DomUs because guests are
started with a static-max value that matches the amount of RAM in the
memory map.
Fix this by forcefully setting target_diff for Dom0, regardless of
it's mode.
Reported-by: Gabriel Bercarug <bercarug@amazon.com> Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Some of fuzzers set panic_on_warn=1 so that they can handle WARN()ings
the same way they handle full-blown kernel crashes. We used WARN() in
input_alloc_absinfo() to get a better idea where memory allocation
failed, but since then kmalloc() and friends started dumping call stack on
memory allocation failures anyway, so we are not getting anything extra
from WARN().
Because of the above, let's replace WARN with dev_err(). We use dev_err()
instead of simply removing message and relying on kcalloc() to give us
stack dump so that we'd know the instance of hardware device to which we
were trying to attach input device.
Since commit 63347db0affa "ACPI / scan: Use acpi_bus_get_status() to
initialize ACPI_TYPE_DEVICE devs" the status field of normal acpi_devices
gets set to 0 by acpi_bus_type_and_status() and filled with its actual
value later when acpi_add_single_object() calls acpi_bus_get_status().
This means that any acpi_match_device_ids() calls in between will always
fail with -ENOENT.
We already have a workaround for this, which temporary forces status to
ACPI_STA_DEFAULT in drivers/acpi/x86/utils.c: acpi_device_always_present()
and the next commit in this series adds another acpi_match_device_ids()
call between status being initialized as 0 and the acpi_bus_get_status()
call.
Rather then adding another workaround, this commit makes
acpi_bus_type_and_status() initialize status to ACPI_STA_DEFAULT, this is
safe to do as the only code looking at status between the initialization
and the acpi_bus_get_status() call is those acpi_match_device_ids() calls.
Note this does mean that we need to (re)set status to 0 in case the
acpi_bus_get_status() call fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Fix a panic that occurs for a device that got an error in
dasd_eckd_check_characteristics() during online processing.
For example the read configuration data command may have failed.
If this error occurs the device is not being set online and the earlier
invoked steps during online processing are rolled back. Therefore
dasd_eckd_uncheck_device() is called which needs a valid private
structure. But this pointer is not valid if
dasd_eckd_check_characteristics() has failed.
Check for a valid device->private pointer to prevent a panic.
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In commit ed996a52c868 ("block: simplify and cleanup bvec pool
handling"), the value of the slab index is incremented by one in
bvec_alloc() after the allocation is done to indicate an index value of
0 does not need to be later freed.
bvec_nr_vecs() was not updated accordingly, and thus returns the wrong
value. Decrement idx before performing the lookup.
Fixes: ed996a52c868 ("block: simplify and cleanup bvec pool handling") Signed-off-by: Greg Edwards <gedwards@ddn.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In some cases, a symbol may have multiple aliases. Attempting to add an
entry probe for such symbols results in a probe being added at an
incorrect location while it fails altogether for return probes. This is
only applicable for binaries with debug information.
During the arch-dependent post-processing, the offset from the start of
the symbol at which the probe is to be attached is determined and added
to the start address of the symbol to get the probe's location. In case
there are multiple aliases, this offset gets added multiple times for
each alias of the symbol and we end up with an incorrect probe location.
This can be verified on a powerpc64le system as shown below.
For both the entry probe and the return probe, the probe location
should be _text+4276888 (0xc000000000414298). Since another alias
exists for 'sys_open', the post-processing code will end up adding
the offset (8 for powerpc64le) twice and perf will attempt to add
the probe at _text+4276896 (0xc0000000004142a0) instead.
Before:
# perf probe -v -a sys_open
probe-definition(0): sys_open
symbol:sys_open file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Looking at the vmlinux_path (8 entries long)
Using /lib/modules/4.18.0-rc8+/build/vmlinux for symbols
Open Debuginfo file: /lib/modules/4.18.0-rc8+/build/vmlinux
Try to find probe point from debuginfo.
Symbol sys_open address found : c000000000414290
Matched function: __se_sys_open [2ad03a0]
Probe point found: __se_sys_open+0
Found 1 probe_trace_events.
Opening /sys/kernel/debug/tracing/kprobe_events write=1
Writing event: p:probe/sys_open _text+4276896
Added new event:
probe:sys_open (on sys_open)
...
# perf probe -v -a sys_open%return $retval
probe-definition(0): sys_open%return
symbol:sys_open file:(null) line:0 offset:0 return:1 lazy:(null)
0 arguments
Looking at the vmlinux_path (8 entries long)
Using /lib/modules/4.18.0-rc8+/build/vmlinux for symbols
Open Debuginfo file: /lib/modules/4.18.0-rc8+/build/vmlinux
Try to find probe point from debuginfo.
Symbol sys_open address found : c000000000414290
Matched function: __se_sys_open [2ad03a0]
Probe point found: __se_sys_open+0
Found 1 probe_trace_events.
Opening /sys/kernel/debug/tracing/README write=0
Opening /sys/kernel/debug/tracing/kprobe_events write=1
Parsing probe_events: p:probe/sys_open _text+4276896
Group:probe Event:sys_open probe:p
Writing event: r:probe/sys_open__return _text+4276896
Failed to write event: Invalid argument
Error: Failed to add events. Reason: Invalid argument (Code: -22)
After:
# perf probe -v -a sys_open
probe-definition(0): sys_open
symbol:sys_open file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Looking at the vmlinux_path (8 entries long)
Using /lib/modules/4.18.0-rc8+/build/vmlinux for symbols
Open Debuginfo file: /lib/modules/4.18.0-rc8+/build/vmlinux
Try to find probe point from debuginfo.
Symbol sys_open address found : c000000000414290
Matched function: __se_sys_open [2ad03a0]
Probe point found: __se_sys_open+0
Found 1 probe_trace_events.
Opening /sys/kernel/debug/tracing/kprobe_events write=1
Writing event: p:probe/sys_open _text+4276888
Added new event:
probe:sys_open (on sys_open)
...
# perf probe -v -a sys_open%return $retval
probe-definition(0): sys_open%return
symbol:sys_open file:(null) line:0 offset:0 return:1 lazy:(null)
0 arguments
Looking at the vmlinux_path (8 entries long)
Using /lib/modules/4.18.0-rc8+/build/vmlinux for symbols
Open Debuginfo file: /lib/modules/4.18.0-rc8+/build/vmlinux
Try to find probe point from debuginfo.
Symbol sys_open address found : c000000000414290
Matched function: __se_sys_open [2ad03a0]
Probe point found: __se_sys_open+0
Found 1 probe_trace_events.
Opening /sys/kernel/debug/tracing/README write=0
Opening /sys/kernel/debug/tracing/kprobe_events write=1
Parsing probe_events: p:probe/sys_open _text+4276888
Group:probe Event:sys_open probe:p
Writing event: r:probe/sys_open__return _text+4276888
Added new event:
probe:sys_open__return (on sys_open%return)
...
Reported-by: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Sandipan Das <sandipan@linux.ibm.com> Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Fixes: 99e608b5954c ("perf probe ppc64le: Fix probe location when using DWARF") Link: http://lkml.kernel.org/r/20180809161929.35058-1-sandipan@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently if you build a 32-bit powerpc kernel and use get_user() to
load a u64 value it will fail to build with eg:
kernel/rseq.o: In function `rseq_get_rseq_cs':
kernel/rseq.c:123: undefined reference to `__get_user_bad'
This is hitting the check in __get_user_size() that makes sure the
size we're copying doesn't exceed the size of the destination:
#define __get_user_size(x, ptr, size, retval)
do {
retval = 0;
__chk_user_ptr(ptr);
if (size > sizeof(x))
(x) = __get_user_bad();
Which doesn't immediately make sense because the size of the
destination is u64, but it's not really, because __get_user_check()
etc. internally create an unsigned long and copy into that:
#define __get_user_check(x, ptr, size)
({
long __gu_err = -EFAULT;
unsigned long __gu_val = 0;
The problem being that on 32-bit unsigned long is not big enough to
hold a u64. We can fix this with a trick from hpa in the x86 code, we
statically check the type of x and set the type of __gu_val to either
unsigned long or unsigned long long.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently when virtio_find_single_vq fails, we go through del_vqs which
throws a warning (Trying to free already-free IRQ). Skip del_vqs if vq
allocation failed.
Link: http://lkml.kernel.org/r/20180524101021.49880-1-jean-philippe.brucker@arm.com Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com> Reviewed-by: Greg Kurz <groug@kaod.org> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
It may be possible to run p9_fd_cancel() with a deleted req->req_list
and incur in a double del. To fix hold the client->lock while changing
the status, so the other threads will be synchronized.
Link: http://lkml.kernel.org/r/20180723184253.6682-1-tomasbortoli@gmail.com Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Reported-by: syzbot+735d926e9d1317c3310c@syzkaller.appspotmail.com
To: Eric Van Hensbergen <ericvh@gmail.com>
To: Ron Minnich <rminnich@sandia.gov>
To: Latchesar Ionkov <lucho@ionkov.net> Cc: Yiwen Jiang <jiangyiwen@huwei.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When compiling bmips with SMP disabled, the build fails with:
drivers/irqchip/irq-bcm7038-l1.o: In function `bcm7038_l1_cpu_offline':
drivers/irqchip/irq-bcm7038-l1.c:242: undefined reference to `irq_set_affinity_locked'
make[5]: *** [vmlinux] Error 1
Fix this by adding and setting bcm7038_l1_cpu_offline only when actually
compiling for SMP. It wouldn't have been used anyway, as it requires
CPU_HOTPLUG, which in turn requires SMP.
Fixes: 34c535793bcb ("irqchip/bcm7038-l1: Implement irq_cpu_offline() callback") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The argument to nsinfo__copy() was assumed to be valid, but some code paths
exist that will lead to NULL being passed.
In particular, running 'perf script -D' on a perf.data file containing an
PERF_RECORD_MMAP event associating the '[vdso]' dso with pid 0 earlier in
the event stream will lead to a segfault.
Since all calling code is already checking for a non-null return value,
just return NULL for this case as well.
Signed-off-by: Benno Evers <bevers@mesosphere.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Krister Johansen <kjlx@templeofstupid.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180810133614.9925-1-bevers@mesosphere.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to the functional specification of hardware, the first
descriptor of response from command 'lookup vlan talbe' is not valid.
Currently, the first descriptor is parsed as normal value, which will
cause an expected error.
This patch fixes this problem by skipping the first descriptor.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Xi Wang <wangxi11@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
hns bitmap allocation functions return 0 on success and -1 on failure.
Callers of these functions wrongly used their return value as an errno,
fix that by making a proper conversion.
Fixes: a598c6f4c5a8 ("IB/hns: Simplify function of pd alloc and qp alloc") Signed-off-by: Gal Pressman <pressmangal@gmail.com> Acked-by: Lijun Ou <oulijun@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Lets not turn the TCP ULP lookup into an arbitrary module loader as
we only intend to load ULP modules through this mechanism, not other
unrelated kernel modules:
Fix it by adding module alias to TCP ULP modules, so probing module
via request_module() will be limited to tcp-ulp-[name]. The existing
modules like kTLS will load fine given tcp-ulp-tls alias, but others
will fail to load:
Shaochun Chen points out we leak dumper filter state allocations
stored in dump_control->data in case there is an error before netlink sets
cb_running (after which ->done will be called at some point).
In order to fix this, add .start functions and move allocations there.
Add entry to WMI keymap for lid flip event on Asus UX360.
On Asus Zenbook ux360 flipping lid from/to tablet mode triggers
keyscan code 0xfa which cannot be handled and results in kernel
log message "Unknown key fa pressed".
Signed-off-by: Aleh Filipovich<aleh@appnexus.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Instantiating the sm501 OHCI subdevice results in a kernel warning.
sm501-usb sm501-usb: SM501 OHCI
sm501-usb sm501-usb: new USB bus registered, assigned bus number 1
WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516
ohci_init+0x194/0x2d8
Modules linked in:
projects / mirror_ubuntu-bionic-kernel.git / log