Older versions of the Juno *SoC* TRM [1] recommended that the UART clock
source should be 7.2738 MHz, whereas the *system* TRM [2] stated a more
correct value of 7.3728 MHz. Somehow the wrong value managed to end up in
our DT.
Doing a prime factorisation, a modulo divide by 115200 and trying
to buy a 7.2738 MHz crystal at your favourite electronics dealer suggest
that the old value was actually a typo. The actual UART clock is driven
by a PLL, configured via a parameter in some board.txt file in the
firmware, which reads 7.37 MHz (sic!).
Fix this to correct the baud rate divisor calculation on the Juno board.
The INTERRUPT_CNTL2 register expects a valid DMA address, but is
currently set with a GPU MC address. This can cause problems on
systems that detect the resulting DMA read from an invalid address
(found on a Power8 guest).
Instead, use the DMA address of the dummy page because it will always
be safe.
Fixes: d8f60cfc9345 ("drm/radeon/kms: Add support for interrupts on r6xx/r7xx chips (v3)") Fixes: 25a857fbe973 ("drm/radeon/kms: add support for interrupts on SI") Fixes: a59781bbe528 ("drm/radeon: add support for interrupts on CIK (v5)") Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In affs_remount if data is provided it is duplicated into new_opts. The
allocated memory for new_opts is only released if parse_options fails.
There's a bit of history behind new_options, originally there was
save/replace options on the VFS layer so the 'data' passed must not
change (thus strdup), this got cleaned up in later patches. But not
completely.
There's no reason to do the strdup in cases where the filesystem does
not need to reuse the 'data' again, because strsep would modify it
directly.
v4.11-rc1 did introduce a patch series that rearranged the
sdio quirks into a header file. Unfortunately this did forget
to handle SDIO_VENDOR_ID_TI differently between wl1251 and
wl1271 with the result that although the wl1251 was found on
the sdio bus, the firmware did not load any more and there was
no interface registration.
This patch defines separate constants to be used by sdio quirks
and drivers.
Fixes: 884f38607897 ("mmc: core: move some sdio IDs out of quirks file") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Adding a couple of READ_ONCE()/WRITE_ONCE() should silence it.
Since the report hinted about multiple cpus using the history
concurrently, I added a test avoiding writing on it if the
victim slot already contains the desired value.
[1]
BUG: KCSAN: data-race in fanout_demux_rollover / fanout_demux_rollover
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18922 Comm: syz-executor.3 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 3b3a5b0aab5b ("packet: rollover huge flows before small flows") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A difference of two unsigned long needs long storage.
Fixes: c7fb64db001f ("[NETLINK]: Neighbour table configuration and statistics via rtnetlink") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2e3 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
By default s_maxbytes is set to MAX_NON_LFS, which limits the usable
file size to 2GB, enforced by the vfs.
Commit b9b1f8d5930a ("AFS: write support fixes") added support for the
64-bit fetch and store server operations, but did not change this value.
As a result, attempts to write past the 2G mark result in EFBIG errors:
$ dd if=/dev/zero of=foo bs=1M count=1 seek=2048
dd: error writing 'foo': File too large
Set s_maxbytes to MAX_LFS_FILESIZE.
Fixes: b9b1f8d5930a ("AFS: write support fixes") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The reset counter is specific for every QCA700x chip. So move this
into the private driver struct. Otherwise we get unpredictable reset
behavior in setups with multiple QCA700x chips.
Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com> Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If packet corruption failed we jump to finish_segs and return
NET_XMIT_SUCCESS. Seeing success will make the parent qdisc
increment its backlog, that's incorrect - we need to return
NET_XMIT_DROP.
Fixes: 6071bd1aa13e ("netem: Segment GSO packets on enqueue") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
To corrupt a GSO frame we first perform segmentation. We then
proceed using the first segment instead of the full GSO skb and
requeue the rest of the segments as separate packets.
If there are any issues with processing the first segment we
still want to process the rest, therefore we jump to the
finish_segs label.
Commit 177b8007463c ("net: netem: fix backlog accounting for
corrupted GSO frames") started using the pointer to the first
segment in the "rest of segments processing", but as mentioned
above the first segment may had already been freed at this point.
Backlog corrections for parent qdiscs have to be adjusted.
Fixes: 177b8007463c ("net: netem: fix backlog accounting for corrupted GSO frames") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Illegal memory will be touch if SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(41) exceed the size of structure sdma_script_start_addrs(40),
thus cause memory corrupt such as slob block header so that kernel
trap into while() loop forever in slob_free(). Please refer to below
code piece in imx-sdma.c:
for (i = 0; i < sdma->script_number; i++)
if (addr_arr[i] > 0)
saddr_arr[i] = addr_arr[i]; /* memory corrupt here */
That issue was brought by commit a572460be9cf ("dmaengine: imx-sdma: Add
support for version 3 firmware") because SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(38->41 3 scripts added) not align with script number added in
sdma_script_start_addrs(2 scripts).
Fixes: a572460be9cf ("dmaengine: imx-sdma: Add support for version 3 firmware") Cc: stable@vger.kernel Link: https://www.spinics.net/lists/arm-kernel/msg754895.html Signed-off-by: Robin Gong <yibin.gong@nxp.com> Reported-by: Jurgen Lambrecht <J.Lambrecht@TELEVIC.com> Link: https://lore.kernel.org/r/1569347584-3478-1-git-send-email-yibin.gong@nxp.com
[vkoul: update the patch title] Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On msm8998, vblank timeouts are observed because the DSI controller is not
reset properly, which ends up stalling the MDP. This is because the reset
logic is not correct per the hardware documentation.
The documentation states that after asserting reset, software should wait
some time (no indication of how long), or poll the status register until it
returns 0 before deasserting reset.
wmb() is insufficient for this purpose since it just ensures ordering, not
timing between writes. Since asserting and deasserting reset occurs on the
same register, ordering is already guaranteed by the architecture, making
the wmb extraneous.
Since we would define a timeout for polling the status register to avoid a
possible infinite loop, lets just use a static delay of 20 ms, since 16.666
ms is the time available to process one frame at 60 fps.
Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support") Cc: Hai Li <hali@codeaurora.org> Cc: Rob Clark <robdclark@gmail.com> Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Reviewed-by: Sean Paul <sean@poorly.run>
[seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS] Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The field "name" in struct ptp_clock_info has a fixed size of 16
chars and is used as zero terminated string by clock_name_show()
in drivers/ptp/ptp_sysfs.c
The current initialization value requires 17 chars to fit also the
null termination, and this causes overflow to the next bytes in
the struct when the string is read as null terminated:
hexdump -C /sys/class/ptp/ptp0/clock_name 00000000 73 74 6d 6d 61 63 5f 70 74 70 5f 63 6c 6f 63 6b |stmmac_ptp_clock| 00000010 a0 ac b9 03 0a |.....|
where the extra 4 bytes (excluding the newline) after the string
represent the integer 0x03b9aca0 = 62500000 assigned to the field
"max_adj" that follows "name" in the same struct.
There is no strict requirement for the "name" content and in the
comment in ptp_clock_kernel.h it's reported it should just be 'A
short "friendly name" to identify the clock'.
Replace it with "stmmac ptp".
Signed-off-by: Antonio Borneo <antonio.borneo@st.com> Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If llc_conn_state_process() sees that llc_conn_service() put the skb on
a list, it will drop one fewer references to it. This is wrong because
the current behavior is that llc_conn_service() never consumes a
reference to the skb.
The code also makes the number of skb references being dropped
conditional on which of ind_prim and cfm_prim are nonzero, yet neither
of these affects how many references are *acquired*. So there is extra
code that tries to fix this up by sometimes taking another reference.
Remove the unnecessary/broken refcounting logic and instead just add an
skb_get() before the only two places where an extra reference is
actually consumed.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
All callers of llc_conn_state_process() except llc_build_and_send_pkt()
(via llc_ui_sendmsg() -> llc_ui_send_data()) assume that it always
consumes a reference to the skb. Fix this caller to do the same.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We can process deauth frames and all, but we drop them very
early in the RX path today - this could never have worked.
Fixes: 2cc59e784b54 ("mac80211: reply to AUTH with DEAUTH if sta allocation fails in IBSS") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/20191004123706.15768-2-luca@coelho.fi Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
"nvme: add a common helper to read Identify Controller data"
has re-introduced an issue that we have attempted to work around in the
past, in commit a310acd7a7ea ("NVMe: use split lo_hi_{read,write}q").
The problem is that some PCIe NVMe controllers do not implement 64-bit
outbound accesses correctly, which is why the commit above switched
to using lo_hi_[read|write]q for all 64-bit BAR accesses occuring in
the code.
In the mean time, the NVMe subsystem has been refactored, and now calls
into the PCIe support layer for NVMe via a .reg_read64() method, which
fails to use lo_hi_readq(), and thus reintroduces the problem that the
workaround above aimed to address.
Given that, at the moment, .reg_read64() is only used to read the
capability register [which is known to tolerate split reads], let's
switch .reg_read64() to lo_hi_readq() as well.
This fixes a boot issue on some ARM boxes with NVMe behind a Synopsys
DesignWare PCIe host controller.
Fixes: 7fd8930f26be4 ("nvme: add a common helper to read Identify Controller data") Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "iface" variable is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: b78624125304 ("of_mdio: Abstract a general interface for phy connect") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "lp->phy_mode" is an enum but in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: ee06b1728b95 ("net: axienet: add support for standard phy-mode binding") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "dwmac->phy_mode" is an enum and in this context GCC treats it as
an unsigned int so the error handling is never triggered.
Fixes: 566e82516253 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The "priv->phy_mode" variable is an enum and in this context GCC will
treat it as unsigned to the error handling will never trigger.
Fixes: 57c5bc9ad7d7 ("net: hisilicon: add hix5hd2 mac driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The irqreturn_t type is an enum or an unsigned int in GCC. That
creates to problems because it can't detect if the
self->aq_hw_ops->hw_irq_read() call fails and at the end the function
always returns IRQ_HANDLED.
drivers/net/ethernet/aquantia/atlantic/aq_vec.c:316 aq_vec_isr_legacy() warn: unsigned 'err' is never less than zero.
drivers/net/ethernet/aquantia/atlantic/aq_vec.c:329 aq_vec_isr_legacy() warn: always true condition '(err >= 0) => (0-u32max >= 0)'
Fixes: 970a2e9864b0 ("net: ethernet: aquantia: Vector operations") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In addr_handler(), assuming status == 0 and the device already has been
acquired (id_priv->cma_dev != NULL), we get the following incorrect
"error" message:
RDMA CM: ADDR_ERROR: failed to resolve IP. status 0
Fixes: 498683c6a7ee ("IB/cma: Add debug messages to error flows") Link: https://lore.kernel.org/r/20190902092731.1055757-1-haakon.bugge@oracle.com Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the FW bundles multiple packets, pkt->act_len may be incorrect
as it refers to the first packet only (however, the FW will only
bundle packets that fit into the same pkt->alloc_len).
Before this patch, the skb length would be set (incorrectly) to
pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually
adjusted in ath10k_sdio_mbox_rx_process_packet.
The first problem is that ath10k_sdio_mbox_rx_process_packet does not
use proper skb_put commands to adjust the length (it directly changes
skb->len), so we end up with a mismatch between skb->head + skb->tail
and skb->data + skb->len. This is quite serious, and causes corruptions
in the TCP stack, as the stack tries to coalesce packets, and relies
on skb->tail being correct (that is, skb_tail_pointer must point to
the first byte_after_ the data).
Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet,
this moves the code to ath10k_sdio_mbox_rx_packet, and also add a
bounds check, as skb_put would crash the kernel if not enough space is
available.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Fixes: 8530b4e7b22bc3b ("ath10k: sdio: set skb len for all rx packets") Signed-off-by: Nicolas Boichat <drinkcat@chromium.org> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
sonic_send_packet will be processed in irq or non-irq
context, so it would better use dev_kfree_skb_any
instead of dev_kfree_skb.
Fixes: d9fb9f384292 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix an error in the bitmaskfor the shtc1 and shtw1 bitmask used to
retrieve the chip ID from the ID register. See section 5.7 of the shtw1
or shtc1 datasheet for details.
Fixes: 1a539d372edd9832444e7a3daa710c444c014dc9 ("hwmon: add support for Sensirion SHTC1 sensor") Signed-off-by: Dan Robertson <dan@dlrobertson.com> Link: https://lore.kernel.org/r/20190905014554.21658-3-dan@dlrobertson.com
[groeck: Reordered to be first in series and adjusted accordingly] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In Xen environment, if Xen-swiotlb is enabled, ixgbe driver
could possibly allocate a page, DMA memory buffer, for the first
fragment which is not suitable for Xen-swiotlb to do DMA operations.
Xen-swiotlb have to internally allocate another page for doing DMA
operations. This mechanism requires syncing the data from the internal
page to the page which ixgbe sends to upper network stack. However,
since commit f3213d932173 ("ixgbe: Update driver to make use of DMA
attributes in Rx path"), the unmap operation is performed with
DMA_ATTR_SKIP_CPU_SYNC. As a result, the sync is not performed.
Since the sync isn't performed, the upper network stack could receive
a incomplete network packet. By incomplete, it means the linear data
on the first fragment(between skb->head and skb->end) is invalid. So
we have to copy the data from the internal xen-swiotlb page to the page
which ixgbe sends to upper network stack through the sync operation.
More details from Alexander Duyck:
Specifically since we are mapping the frame with
DMA_ATTR_SKIP_CPU_SYNC we have to unmap with that as well. As a result
a sync is not performed on an unmap and must be done manually as we
skipped it for the first frag. As such we need to always sync before
possibly performing a page unmap operation.
Fixes: f3213d932173 ("ixgbe: Update driver to make use of DMA attributes in Rx path") Signed-off-by: Firo Yang <firo.yang@suse.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
generic_write_checks() may modify iov_iter_count(), so we must get the
count after the call, not before. Using the wrong one has a couple of
consequences:
1. We check a longer range in check_can_nocow() for nowait than we're
actually writing.
2. We create extra hole extent maps in btrfs_cont_expand(). As far as I
can tell, this is harmless, but I might be missing something.
These issues are pretty minor, but let's fix it before something more
important trips on it.
Fixes: edf064e7c6fe ("btrfs: nowait aio support") Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If the caching thread fails to allocate a path, it returns without waking
up any cache waiters, leaving them hang forever. Fix this by following the
same approach as when we fail to start the caching thread: print an error
message, disable inode caching and make the wakers fallback to non-caching
mode behaviour (calling btrfs_find_free_objectid()).
Fixes: 581bb050941b4f ("Btrfs: Cache free inode numbers in memory") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we fail to start the inode caching thread, we print an error message
and disable the inode cache, however we never wake up any waiters, so they
hang forever waiting for the caching to finish. Fix this by waking them
up and have them fallback to a call to btrfs_find_free_objectid().
Fixes: e60efa84252c05 ("Btrfs: avoid triggering bug_on() when we fail to start inode caching task") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we are able to load an existing inode cache off disk, we set the state
of the cache to BTRFS_CACHE_FINISHED, but we don't wake up any one waiting
for the cache to be available. This means that anyone waiting for the
cache to be available, waiting on the condition that either its state is
BTRFS_CACHE_FINISHED or its available free space is greather than zero,
can hang forever.
This could be observed running fstests with MOUNT_OPTIONS="-o inode_cache",
in particular test case generic/161 triggered it very frequently for me,
producing a trace like the following:
[63795.739712] BTRFS info (device sdc): enabling inode map caching
[63795.739714] BTRFS info (device sdc): disk space caching is enabled
[63795.739716] BTRFS info (device sdc): has skinny extents
[64036.653886] INFO: task btrfs-transacti:3917 blocked for more than 120 seconds.
[64036.654079] Not tainted 5.2.0-rc4-btrfs-next-50 #1
[64036.654143] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[64036.654232] btrfs-transacti D 0 3917 2 0x80004000
[64036.654239] Call Trace:
[64036.654258] ? __schedule+0x3ae/0x7b0
[64036.654271] schedule+0x3a/0xb0
[64036.654325] btrfs_commit_transaction+0x978/0xae0 [btrfs]
[64036.654339] ? remove_wait_queue+0x60/0x60
[64036.654395] transaction_kthread+0x146/0x180 [btrfs]
[64036.654450] ? btrfs_cleanup_transaction+0x620/0x620 [btrfs]
[64036.654456] kthread+0x103/0x140
[64036.654464] ? kthread_create_worker_on_cpu+0x70/0x70
[64036.654476] ret_from_fork+0x3a/0x50
[64036.654504] INFO: task xfs_io:3919 blocked for more than 120 seconds.
[64036.654568] Not tainted 5.2.0-rc4-btrfs-next-50 #1
[64036.654617] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[64036.654685] xfs_io D 0 3919 3633 0x00000000
[64036.654691] Call Trace:
[64036.654703] ? __schedule+0x3ae/0x7b0
[64036.654716] schedule+0x3a/0xb0
[64036.654756] btrfs_find_free_ino+0xa9/0x120 [btrfs]
[64036.654764] ? remove_wait_queue+0x60/0x60
[64036.654809] btrfs_create+0x72/0x1f0 [btrfs]
[64036.654822] lookup_open+0x6bc/0x790
[64036.654849] path_openat+0x3bc/0xc00
[64036.654854] ? __lock_acquire+0x331/0x1cb0
[64036.654869] do_filp_open+0x99/0x110
[64036.654884] ? __alloc_fd+0xee/0x200
[64036.654895] ? do_raw_spin_unlock+0x49/0xc0
[64036.654909] ? do_sys_open+0x132/0x220
[64036.654913] do_sys_open+0x132/0x220
[64036.654926] do_syscall_64+0x60/0x1d0
[64036.654933] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fix this by adding a wake_up() call right after setting the cache state to
BTRFS_CACHE_FINISHED, at start_caching(), when we are able to load the
cache from disk.
Fixes: 82d5902d9c681b ("Btrfs: Support reading/writing on disk free ino cache") Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
NETDEV_TX_BUSY really should only be used by drivers that call
netif_tx_stop_queue() at the wrong moment. If dma_map_single() is
failed to map tx DMA buffer, it might trigger an infinite loop.
This patch use NETDEV_TX_OK instead of NETDEV_TX_BUSY, and change
printk to pr_err_ratelimited.
Fixes: d9fb9f384292 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When dealing with 32-bit variant of LPUART IP block appropriate I/O
helpers have to be used to properly deal with endianness
differences. Change all of the offending code to do that.
Fixes: a5fa2660d787 ("tty/serial/fsl_lpuart: Add CONSOLE_POLL support
for lpuart32.") Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Cc: Chris Healy <cphealy@gmail.com> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: linux-imx@nxp.com Cc: linux-serial@vger.kernel.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/20190729195226.8862-14-andrew.smirnov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the pointer val is being incorrectly incremented
instead of the value pointed to by val. Fix this by adding
in the missing * indirection operator.
Addresses-Coverity: ("Unused value") Fixes: c03f2c536818 ("staging:iio:dac: Add AD5380 driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
An earlier commit re-worked the setting of the bitmask and is now
assigning v with some bit flags rather than bitwise or-ing them
into v, consequently the earlier bit-settings of v are being lost.
Fix this by replacing an assignment with the bitwise or instead.
Addresses-Coverity: ("Unused value") Fixes: 2be25cac8402 ("bcma: add constants for PCI and use them") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Recently device pass-through stops working for Linux VM running on Hyper-V.
git-bisect shows the regression is caused by the recent commit 467a3bb97432 ("PCI: hv: Allocate a named fwnode ..."), but the root cause
is that the commit d59f6617eef0 forgets to set the domain->fwnode for
IRQCHIP_FWNODE_NAMED*, and as a result:
1. The domain->fwnode remains to be NULL.
2. irq_find_matching_fwspec() returns NULL since "h->fwnode == fwnode" is
false, and pci_set_bus_msi_domain() sets the Hyper-V PCI root bus's
msi_domain to NULL.
3. When the device is added onto the root bus, the device's dev->msi_domain
is set to NULL in pci_set_msi_domain().
4. When a device driver tries to enable MSI-X, pci_msi_setup_msi_irqs()
calls arch_setup_msi_irqs(), which uses the native MSI chip (i.e.
arch/x86/kernel/apic/msi.c: pci_msi_controller) to set up the irqs, but
actually pci_msi_setup_msi_irqs() is supposed to call
msi_domain_alloc_irqs() with the hbus->irq_domain, which is created in
hv_pcie_init_irq_domain() and is associated with the Hyper-V chip
hv_msi_irq_chip. Consequently, the irq line is not properly set up, and
the device driver can not receive any interrupt.
Fixes: d59f6617eef0 ("genirq: Allow fwnode to carry name information only") Fixes: 467a3bb97432 ("PCI: hv: Allocate a named fwnode instead of an address-based one") Reported-by: Lili Deng <v-lide@microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/PU1P153MB01694D9AF625AC335C600C5FBFBE0@PU1P153MB0169.APCP153.PROD.OUTLOOK.COM Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The problem is in gb_lights_request_handler(). If we get a request to
change the config then we release the light with gb_lights_light_release()
and re-allocated it. However, if the allocation fails part way through
then we call gb_lights_light_release() again. This can lead to a couple
different double frees where we haven't cleared out the original values:
I also made a small change to how we set "light->channels_count = 0;".
The original code handled this part fine and did not cause a use after
free but it was sort of complicated to read.
We may want to use the device pointer in device_init_wakeup() with
functions that expect the device to already be added with device_add().
For example, if we were to link the device initializing wakeup to
something in sysfs such as a class for wakeups we'll run into an error.
It looks like this code was written with the assumption that the device
would be added before initializing wakeup due to the order of operations
in power_supply_unregister().
Let's change the order of operations so we don't run into problems here.
Fixes: 948dcf966228 ("power_supply: Prevent suspend until power supply events are processed") Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Tri Vo <trong@android.com> Cc: Kalesh Singh <kaleshsingh@google.com> Cc: Ravi Chandra Sadineni <ravisadineni@chromium.org> Cc: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Writes into limit registers fail if the temperature written is negative.
The regmap write operation checks the value range, regmap_write accepts
an unsigned int as parameter, and the temperature value passed to
regmap_write is kept in a variable declared as long. Negative values
are converted large unsigned integers, which fails the range check.
Fix by type casting the temperature to u16 when calling regmap_write().
Cc: Iker Perez del Palomar Sustatxa <iker.perez@codethink.co.uk> Fixes: e65365fed87f ("hwmon: (lm75) Convert to use regmap") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit dfe2a77fd243 ("kfifo: fix kfifo_alloc() and kfifo_init()") made
the kfifo code round the number of elements up. That was good for
__kfifo_alloc(), but it's actually wrong for __kfifo_init().
The difference? __kfifo_alloc() will allocate the rounded-up number of
elements, but __kfifo_init() uses an allocation done by the caller. We
can't just say "use more elements than the caller allocated", and have
to round down.
The good news? All the normal cases will be using power-of-two arrays
anyway, and most users of kfifo's don't use kfifo_init() at all, but one
of the helper macros to declare a KFIFO that enforce the proper
power-of-two behavior. But it looks like at least ibmvscsis might be
affected.
The bad news? Will Deacon refers to an old thread and points points out
that the memory ordering in kfifo's is questionable. See
The commit ed08d40cdec4
("ahci: Changing two module params with static and __read_mostly")
moved ahci_em_messages to be static while missing the fact of exporting it.
WARNING: "ahci_em_messages" [vmlinux] is a static EXPORT_SYMBOL_GPL
Drop export for the local variable ahci_em_messages.
Fixes: ed08d40cdec4 ("ahci: Changing two module params with static and __read_mostly") Cc: Chuansheng Liu <chuansheng.liu@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Region 'A'(I/O) can not be mapped by M4U; For Region 'B'/'C'/'D', the
bit32 of the CPU physical address always is needed to set, and for Region
'E', the CPU physical address keep as is. something looks like this:
CPU PA -> M4U OUTPUT PA
0x4000_0000 0x1_4000_0000 (Add bit32)
0x8000_0000 0x1_8000_0000 ...
0xc000_0000 0x1_c000_0000 ...
0x1_0000_0000 0x1_0000_0000 (No change)
Additionally, the iommu consumers always use the CPU phyiscal address.
The PA in the iova_to_phys that is got from v7s always is u32, But
from the CPU point of view, PA only need add BIT(32) when PA < 0x4000_0000.
Fixes: 30e2fccf9512 ("iommu/mediatek: Enlarge the validate PA range
for 4GB mode") Signed-off-by: Yong Wu <yong.wu@mediatek.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The code in question is modifying a variable declared const through
pointer manipulation. Such code is explicitly undefined behavior, and
is the lone issue preventing malta_defconfig from booting when built
with Clang:
If an attempt is made to modify an object defined with a const-qualified
type through use of an lvalue with non-const-qualified type, the
behavior is undefined.
LLVM is removing such assignments. A simple fix is to not declare
variables const that you plan on modifying. Limiting the scope would be
a better method of preventing unwanted writes to such a variable.
Further, the code in question mentions "compiler bugs" without any links
to bug reports, so it is difficult to know if the issue is resolved in
GCC. The patch was authored in 2006, which would have been GCC 4.0.3 or
4.1.1. The minimal supported version of GCC in the Linux kernel is
currently 4.6.
For what its worth, there was UB before the commit in question, it just
added a barrier and got lucky IRT codegen. I don't think there's any
actual compiler bugs related, just runtime bugs due to UB.
Link: https://github.com/ClangBuiltLinux/linux/issues/610 Fixes: 966f4406d903 ("[MIPS] Work around bad code generation for <asm/io.h>.") Reported-by: Nathan Chancellor <natechancellor@gmail.com> Debugged-by: Nathan Chancellor <natechancellor@gmail.com> Suggested-by: Eli Friedman <efriedma@quicinc.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: ralf@linux-mips.org Cc: jhogan@kernel.org Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Hassan Naveed <hnaveed@wavecomp.com> Cc: Stephen Kitt <steve@sk2.org> Cc: Serge Semin <fancer.lancer@gmail.com> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: clang-built-linux@googlegroups.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The previous fix listed bulk read of registers as root cause of
accendential disabling of watchdog, since the watchdog counter
register (WD_VAL) was zeroed.
Fixes: 3769a375ab83 rtc: pcf2127: bulk read only date and time registers.
Tested with the same PCF2127 chip as Sean reveled root cause
of WD_VAL register value zeroing was caused by reading CTRL2
register which is one of the watchdog feature control registers.
So the solution is to not read the first two control registers
(CTRL1 and CTRL2) in pcf2127_rtc_read_time as they are not
needed anyway. Size of local buf variable is kept to allow
easy usage of register defines to improve readability of code.
Debug trace line was updated after CTRL1 and CTRL2 are no longer
read from the chip. Also replaced magic numbers in buf access
with register defines.
In case of sensor malfunction, stop streaming timeout takes much longer
than expected. This is due to conversion of time to jiffies: milliseconds
multiplied with HZ (ticks/second) gives out a value of jiffies with 10^3
greater. We need to also divide by 10^3 to obtain the right jiffies value.
In other words FRAME_INTERVAL_MILLI_SEC must be in seconds in order to
multiply by HZ and get the right jiffies value to add to the current
jiffies for the timeout expire time.
My recent to change to only use force_sig for a synchronous events
wound up breaking signal reception cifs and drbd. I had overlooked
the fact that by default kthreads start out with all signals set to
SIG_IGN. So a change I thought was safe turned out to have made it
impossible for those kernel thread to catch their signals.
Reverting the work on force_sig is a bad idea because what the code
was doing was very much a misuse of force_sig. As the way force_sig
ultimately allowed the signal to happen was to change the signal
handler to SIG_DFL. Which after the first signal will allow userspace
to send signals to these kernel threads. At least for
wake_ack_receiver in drbd that does not appear actively wrong.
So correct this problem by adding allow_kernel_signal that will allow
signals whose siginfo reports they were sent by the kernel through,
but will not allow userspace generated signals, and update cifs and
drbd to call allow_kernel_signal in an appropriate place so that their
thread can receive this signal.
Fixing things this way ensures that userspace won't be able to send
signals and cause problems, that it is clear which signals the
threads are expecting to receive, and it guarantees that nothing
else in the system will be affected.
This change was partly inspired by similar cifs and drbd patches that
added allow_signal.
Reported-by: ronnie sahlberg <ronniesahlberg@gmail.com> Reported-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> Tested-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> Cc: Steve French <smfrench@gmail.com> Cc: Philipp Reisner <philipp.reisner@linbit.com> Cc: David Laight <David.Laight@ACULAB.COM> Fixes: 247bc9470b1e ("cifs: fix rmmod regression in cifs.ko caused by force_sig changes") Fixes: 72abe3bcf091 ("signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig") Fixes: fee109901f39 ("signal/drbd: Use send_sig not force_sig") Fixes: 3cf5d076fb4d ("signal: Remove task parameter from force_sig") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If FW returns FRAG_ERR in response error code, driver is resending the
command only when HWRM command returns success. Fix the code to resend
NVM_INSTALL_UPDATE command with DEFRAG install flags, if FW returns
FRAG_ERR in its response error code.
Fixes: cb4d1d626145 ("bnxt_en: Retry failed NVM_INSTALL_UPDATE with defragmentation flag enabled.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently when the call to ext4_htree_store_dirent fails the error return
variable 'ret' is is not being set to the error code and variable count is
instead, hence the error code is not being returned. Fix this by assigning
ret to the error return code.
Addresses-Coverity: ("Unused value") Fixes: 8af0f0822797 ("ext4: fix readdir error in the case of inline_data+dir_index") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fixes: 72abe3bcf091 ("signal/cifs: Fix cifs_put_tcp_session to call send_sig instead of force_sig")
The global change from force_sig caused module unloading of cifs.ko
to fail (since the cifsd process could not be killed, "rmmod cifs"
now would always fail)
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In commit 365ad353c256 ("tipc: reduce risk of user starvation during
link congestion") we allowed senders to add exactly one list of extra
buffers to the link backlog queues during link congestion (aka
"oversubscription"). However, the criteria for when to stop adding
wakeup messages to the input queue when the overload abates is
inaccurate, and may cause starvation problems during very high load.
Currently, we stop adding wakeup messages after 10 total failed attempts
where we find that there is no space left in the backlog queue for a
certain importance level. The counter for this is accumulated across all
levels, which may lead the algorithm to leave the loop prematurely,
although there may still be plenty of space available at some levels.
The result is sometimes that messages near the wakeup queue tail are not
added to the input queue as they should be.
We now introduce a more exact algorithm, where we keep adding wakeup
messages to a level as long as the backlog queue has free slots for
the corresponding level, and stop at the moment there are no more such
slots or when there are no more wakeup messages to dequeue.
Fixes: 365ad35 ("tipc: reduce risk of user starvation during link congestion") Reported-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A lot of places in the driver use onyx_read_register() without
checking the return value, and it's been working OK for ~10 years
or so, so probably never fails ... Rather than trying to check the
return value everywhere, which would be relatively intrusive, at
least make sure we don't use an uninitialized value.
Fixes: f3d9478b2ce4 ("[ALSA] snd-aoa: add snd-aoa") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Each of the operations in ccp_run_cmd() needs several hundred
bytes of kernel stack. Depending on the inlining, these may
need separate stack slots that add up to more than the warning
limit, as shown in this clang based build:
drivers/crypto/ccp/ccp-ops.c:871:12: error: stack frame size of 1164 bytes in function 'ccp_run_aes_cmd' [-Werror,-Wframe-larger-than=]
static int ccp_run_aes_cmd(struct ccp_cmd_queue *cmd_q, struct ccp_cmd *cmd)
The problem may also happen when there is no warning, e.g. in the
ccp_run_cmd()->ccp_run_aes_cmd()->ccp_run_aes_gcm_cmd() call chain with
over 2000 bytes.
Mark each individual function as 'noinline_for_stack' to prevent
this from happening, and move the calls to the two special cases for aes
into the top-level function. This will keep the actual combined stack
usage to the mimimum: 828 bytes for ccp_run_aes_gcm_cmd() and
at most 524 bytes for each of the other cases.
Generally, declaring a platform device as a static variable is
a bad idea and can cause all kinds of problems, in particular
with the DMA configuration and lifetime rules.
A specific problem we hit here is from a bug in clang that warns
about certain (otherwise valid) macros when used in static variables:
A slightly better way here is to create the platform device dynamically
and set the dma mask in the probe function.
This avoids the warning and some other problems, but is still not ideal
because the device creation should really be separated from the driver,
and the fact that the device has no parent means we have to force
the dma mask rather than having it set up from the bus that the device
is actually on.
Fixes: dd8d8d44df64 ("misc: mic: MIC card driver specific changes to enable SCIF") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20190712092426.872625-1-arnd@arndb.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Don't do extra cpu_to_le32 conversion for
put_unaligned_le32 because it is already implemented
in this function.
Fixes sparse error:
xhci-hub.c:1152:44: warning: incorrect type in argument 1 (different base types)
xhci-hub.c:1152:44: expected unsigned int [usertype] val
xhci-hub.c:1152:44: got restricted __le32 [usertype]
Fixes: 395f540 "xhci: support new USB 3.1 hub request to get extended port status" Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com> Link: https://lore.kernel.org/r/1562501839-26522-1-git-send-email-ruslan.bilovol@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
clang warns about an overly large stack frame in one function
when it decides to inline all __qed_get_vport_*() functions into
__qed_get_vport_stats():
drivers/net/ethernet/qlogic/qed/qed_l2.c:1889:13: error: stack frame size of 1128 bytes in function '_qed_get_vport_stats' [-Werror,-Wframe-larger-than=]
Use a noinline_for_stack annotation to prevent clang from inlining
these, which keeps the maximum stack usage at around half of that
in the worst case, similar to what we get with gcc.
Fixes: 86622ee75312 ("qed: Move statistics to L2 code") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It is not actually guaranteed that pm_abort_suspend will be
nonzero when pm_system_cancel_wakeup() is called which may lead to
subtle issues, so make it use atomic_dec_if_positive() instead of
atomic_dec() for the safety sake.
Fixes: 33e4f80ee69b ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently if lport is null then the null lport pointer is dereference when
printing out debug via the FC_LPORT_DB macro. Fix this by using the more
generic FC_LIBFC_DBG debug macro instead that does not use lport.
Addresses-Coverity: ("Dereference after null check") Fixes: 7414705ea4ae ("libfc: Add runtime debugging with debug_logging module parameter") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The phy_dn variable is still being used in of_phy_connect() after the
of_node_put() call, which may result in use-after-free.
Fixes: 1dd2d06c0459 ("net: Rework pasemi_mac driver to use of_mdio infrastructure") Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: "David S. Miller" <davem@davemloft.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
devm_ioremap_resource() does not currently take 'const' arguments,
which results in a warning from the first driver trying to do it
anyway:
drivers/gpio/gpio-amd-fch.c: In function 'amd_fch_gpio_probe':
drivers/gpio/gpio-amd-fch.c:171:49: error: passing argument 2 of 'devm_ioremap_resource' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
priv->base = devm_ioremap_resource(&pdev->dev, &amd_fch_gpio_iores);
^~~~~~~~~~~~~~~~~~~
Change the prototype to allow it, as there is no real reason not to.
net/rxrpc/output.c: In function ‘rxrpc_send_data_packet’:
net/rxrpc/output.c:338: warning: ‘ret’ may be used uninitialized in this function
Indeed, if the first jump to the send_fragmentable label is made, and
the address family is not handled in the switch() statement, ret will be
used uninitialized.
Fix this by BUG()'ing as is done in other places in rxrpc where internal
support for future address families will need adding. It should not be
possible to reach this normally as the address families are checked
up-front.
Fixes: 5a924b8951f835b5 ("rxrpc: Don't store the rxrpc header in the Tx queue sk_buffs") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
ida instances allocate some internal memory for ->free_bitmap
in addition to the base 'struct ida'. Use ida_destroy() to release
that memory at module_exit().
Fixes: 4b45efe85263 ("mfd: Add support for Intel Sunrisepoint LPSS devices") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Make it safe to call iommu_disable during early init error conditions
before mmio_base is set, but after the struct amd_iommu has been added
to the amd_iommu_list. For example, this happens if firmware fails to
fill in mmio_phys in the ACPI table leading to a NULL pointer
dereference in iommu_feature_disable.
Fixes: 2c0ae1720c09c ('iommu/amd: Convert iommu initialization to state machine') Signed-off-by: Kevin Mitchell <kevmitch@arista.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After ethtool loopback packet tests, we re-open the nic for the next
IRQ test. If the open fails, we must not proceed with the IRQ test
or we will crash with NULL pointer dereference. Fix it by checking
the bnxt_open_nic() return code before proceeding.
Reported-by: Somasundaram Krishnasamy <somasundaram.krishnasamy@oracle.com> Fixes: 67fea463fd87 ("bnxt_en: Add interrupt test to ethtool -t selftest.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The i.MX6 and i.MX8 both have a bit-field spanning bits 27:22 called the
WAIT field.
The WAIT field according to the documentation for both parts "specifies
time interval between auto read and write access in one time program. It is
given in number of ipg_clk periods."
This patch ensures that the relevant field is read and written back to the
timing register.
080edf75d337 ("dmaengine: hsu: set HSU_CH_MTSR to memory width")
has been mistakenly submitted. The further investigations show that
the original code does better job since the memory side transfer size
has never been configured by DMA users.
As per latest revision of documentation: "Channel minimum transfer size
(CHnMTSR)... For IOSF UART, maximum value that can be programmed is 64 and
minimum value that can be programmed is 1."
These regs are write-only, and the hw throws a hissy-fit (ie. reboots)
when we try to read them for GPU state snapshot, in response to a GPU
hang. It is rather impolite when GPU recovery triggers an insta-
reboot, so lets remove the TPL1 registers from the snapshot.
Fixes: 7198e6b03155 drm/msm: add a3xx gpu support Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Besides the alarm, the PCF8563 also has a timer triggered interrupt.
In cases where the previous system left the timer and interrupts on,
or somehow the bits got enabled, the interrupt would keep triggering
as the kernel doesn't know about it.
Clear both the alarm and timer event flags, and disable the interrupts,
before requesting the interrupt line.