Mario Kleiner [Mon, 28 Dec 2020 18:50:58 +0000 (19:50 +0100)]
drm/amd/display: Check plane scaling against format specific hw plane caps.
This takes hw constraints specific to pixel formats into account,
e.g., the inability of older hw to scale fp16 format framebuffers.
It should now allow safely to enable fp16 formats also on DCE-8,
DCE-10, DCE-11.0
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change the #ifdef to an if(IS_ENABLED()) check to fix the warning
and avoid adding more #ifdefs.
Fixes: c920888c604d ("drm/amd/display: Expose new CRC window property") Reviewed-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tian Tao [Mon, 21 Dec 2020 11:16:35 +0000 (19:16 +0800)]
drm/amd/display: remove useless else if
Fix the following coccinelle report:
drivers/gpu/drm/amd/display/dc/dcn302/dcn302_resource.c:1357:6-8:
WARNING: possible condition with no effect (if == else)
Signed-off-by: Tian Tao <tiantao6@hisilicon.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Tue, 29 Dec 2020 09:19:37 +0000 (17:19 +0800)]
drm/amd/pm: improve the fine grain tuning function for RV/RV2/PCO
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together. So this patch adds one flag to avoid this confusion, the flag
will make these two sysfs nodes work separately.
The flag is set as "disabled" by default, so the fine grain tuning function
will be disabled by default.
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag will be set as "enabled",
and the fine grain tuning function will be enabled.
In other profile modes, including "auto", "high", "low",
"profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk", the flag will be set as "disabled",
and the od range of fine grain tuning function will
be restored default value.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Likun Gao [Mon, 28 Dec 2020 09:04:06 +0000 (17:04 +0800)]
drm/amdgpu: remove redundant logic related HDP
Remove hdp_flush function from amdgpu_nbio struct as it have been unified
into hdp struct.
Remove the include about hdp register which was not used.
V2: Remove hdp golden setting which is unnecessary.
Likun Gao [Mon, 28 Dec 2020 08:54:16 +0000 (16:54 +0800)]
drm/amdgpu: switch hdp callback functions for hdp v4
Switch to use the HDP functions which unified on hdp structure instead of
the scattered hdp callback functions.
V2: clean up hdp reset ras error count function.
Jiawei Gu [Wed, 23 Dec 2020 05:54:57 +0000 (13:54 +0800)]
drm/amdgpu: fix potential NULL pointer when check_atom_bios() fails
Asic funcs pointer needs being checked whether is NULL. Because when
check_atom_bios() fails in req_init_data handshake, asic funcs pointer
is not initialized yet.
Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chen Li [Fri, 25 Dec 2020 03:58:00 +0000 (11:58 +0800)]
drm/amdgpu: use GTT for uvd_get_create/destory_msg
On modern gpus, GTT (system memory) works as well here, and this may
also be a workaround for platforms which cannot map vram correctly.
Signed-off-by: chenli <chenli@uniontech.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Obviously, the __memset call is generated by gcc(8.3.1). It optimizes
this for loop into memset. But this may break on some platforms which
cannot map device memory correctly. So, just invoke `writel` to handle this.
v3 (chk): minor cleanups in code and commit message
Signed-off-by: Chen Li <chenli@uniontech.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dennis Li [Wed, 30 Dec 2020 11:45:15 +0000 (19:45 +0800)]
drm/amdgpu: fix a GPU hang issue when remove device
When GFXOFF is enabled and GPU is idle, driver will fail to access some
registers. Therefore change to disable power gating before all access
registers with MMIO.
Signed-off-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dennis Li [Wed, 30 Dec 2020 02:27:42 +0000 (10:27 +0800)]
drm/amdgpu: fix a memory protection fault when remove amdgpu device
ASD and TA share the same firmware in SIENNA_CICHLID and only TA
firmware is requested during boot, so only need release TA firmware when
remove device.
Signed-off-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Thu, 24 Dec 2020 10:04:30 +0000 (18:04 +0800)]
drm/amd/pm: add support to umd P-state function for vangogh
This patch is to add support to umd P-state function for vangogh.
It enables the "set" function of 3 sysfs nodes: pp_dpm_mclk,
pp_dpm_fclk, pp_dpm_socclk, the functions is used to set the DPM
frequency level of memclk/fclk/socclk.
Due to only after enabling the "power_dpm_force_performance_level"
sysfs node, it is allowed to set these three nodes,
so this patch also enables the "powe_dpm_force_performance_level"
sysfs node, which is used to change power profile.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Thu, 24 Dec 2020 08:19:19 +0000 (16:19 +0800)]
drm/amd/pm: add the fine grain tuning function for renoir
This patch is to add the fine grain tuning function for renoir.
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should
be limited in the safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "standard"
$ cat power_dpm_force_performance_level
auto
$ echo "profile_standard" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
profile_standard
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Fri, 18 Dec 2020 06:32:02 +0000 (14:32 +0800)]
drm/amd/pm: improve the fine grain tuning function for RV/RV2/PCO
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be limited in the
safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "manual"
$ cat power_dpm_force_performance_level
auto
$ echo "manual" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
manual
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Thu, 24 Dec 2020 08:11:33 +0000 (16:11 +0800)]
drm/amd/pm: enable the "fetch" function of pp_dpm_vclk/dclk for vangogh
This patch is to enable the "fetch" function of pp_dpm_vclk and
pp_dpm_dclk.
It allows to fetch the current frequency of vcn and dcn and their
DPM levels for vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Wed, 16 Dec 2020 06:44:10 +0000 (14:44 +0800)]
drm/amd/pm: add two new sysfs nodes for vangogh
This patch is to add two new sysfs nodes for vangogh:
pp_dpm_dclk and pp_dpm_vclk.
The two sysfs nodes are similar to pp_dpm_fclk/memclk/socclk.
pp_dpm_dclk represents the DPM frequency of dcn unit.
pp_dpm_vclk represents the DPM frequency of vcn unit.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Wed, 16 Dec 2020 03:26:43 +0000 (11:26 +0800)]
drm/amd/pm: add new feature map macros to resolve duplicate name
This patch is to add new feature map macros to resolve duplicate name.
Vangogh uses one different format to name some feature bits of swSMU, it
causes some duplicate name in the existing feature map list.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiaojian Du [Tue, 15 Dec 2020 08:41:26 +0000 (16:41 +0800)]
drm/amd/pm: add support to umd P-state "fetch" function for vangogh
This patch is to add supoort to umd P-state function for vangogh.
It enables the "fetch" function of 3 sysfs nodes: pp_dpm_mclk,
pp_dpm_fclk, pp_dpm_socclk,the function is used to fetch
the current frequency of memclk/fclk/socclk.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com> Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Thu, 19 Nov 2020 09:30:43 +0000 (17:30 +0800)]
drm/amd/pm: support overdrive vddgfx offset setting(V2)
This is supported by Sienna Cichlid, Navy Flounder and Dimgrey
Cavefish. For these ASICs, the target voltage calculation can be
illustrated by "voltage = voltage calculated from v/f curve +
overdrive vddgfx offset".
V2: limit the smu_version check for Sienna Cichlid only
Here are some sample usages about this new OD setting:
1. Check current vddgfx offset setting by
cat /sys/class/drm/card0/device/pp_od_clk_voltage
...
...
OD_VDDGFX_OFFSET:
0mV
...
...
2. Set new vddgfx offset by
echo "vo 10" > /sys/class/drm/card0/device/pp_od_clk_voltage
cat /sys/class/drm/card0/device/pp_od_clk_voltage
...
...
OD_VDDGFX_OFFSET:
10mV
...
...
3. Commit the new setting by
echo "c" > /sys/class/drm/card0/device/pp_od_clk_voltage
Signed-off-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jinzhou Su [Thu, 17 Dec 2020 09:37:38 +0000 (17:37 +0800)]
drm/amd/pm: Add interface for request WGPs
When user specifies a reduced WGP(CU) config via disalbe_cu module
parameter, this does not disable the clocks which uses additional
power. This interface send active WGP number to SMU and SMU will
cooperate with RLC to power off relative WGPs.
v2: Add request active WGPs in Vangogh smu post init.
Signed-off-by: Ryan Taylor <Ryan.Taylor@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Sat, 12 Dec 2020 14:16:58 +0000 (22:16 +0800)]
drm/amdgpu: drop ih reroute function from psp v11
For all the ASICs that integrate psp v11, vega20
doesn't support ih reroute. arcturus and later will
allow kernel driver to program ih_cfg_index/data
through mmio directly. navi1x and onwards will only
support grb_ih_set command in sriov configuration.
psp_v11_0_reroute_ih is not needed any more.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Mon, 30 Nov 2020 16:23:16 +0000 (00:23 +0800)]
drm/amdgpu: drop IH_CHICKEN programming from vega10 ih block
except for RENOIR, it is not correct to have
IH_CHICKEN programming in vega10 ih block.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Mon, 30 Nov 2020 16:04:36 +0000 (00:04 +0800)]
drm/amdgpu: correct ih_chicken programming for vega10/vega20 ih blocks
IH_CHICKEN.MC_SPACE_FBPA_ENABLE field is only
valid when IH_RB_CNTL.MC_SPACE is programed to 0x3,
frame buffer physical address. For both bus address
and gpu virtual address, don't program MC_SPACE_FBPA_ENABLE
field
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Wed, 9 Dec 2020 05:49:01 +0000 (13:49 +0800)]
drm/amdgpu: retire the vega20 code path from navi10 ih block
already switched to vega20 ih block for vega20
and arcturus. no need to add vega20 support in
navi10 ih block
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Mon, 30 Nov 2020 15:36:57 +0000 (23:36 +0800)]
drm/amdgpu: switch to vega20 ih block for vega20/arcturus
replace navi10 ih block with vega20 ih block for
vega20 and arcturus
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Wed, 9 Dec 2020 05:47:20 +0000 (13:47 +0800)]
drm/amdgpu: reroute vmc/utcl2 interrupts to ih ring 1 for arcturus
in case page faults overwhlem the interrupt handlers
and the driver lost the valuable interrupt information
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Fri, 18 Dec 2020 13:48:59 +0000 (21:48 +0800)]
drm/amdgpu: create vega20 ih blocks
vega20 ih blocks will be used for vega20/arcturus
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 8 Dec 2020 09:22:30 +0000 (17:22 +0800)]
drm/amdgpu: add osssys v4_2 ip headers (v2)
v1: add osssys v4_2 register offset and shift masks
header files. vega20 and arcturus will refer to
these ip headers. (Hawking)
v2: clean up osssys v4_2 registers (Alex)
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Hawking Zhang [Wed, 25 Nov 2020 07:29:42 +0000 (15:29 +0800)]
drm/amdgpu: switch to common decode iv helper
The iv format is the same for all the soc15 adpater
and onwards and can share a common function to
decode iv.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Wed, 25 Nov 2020 07:25:51 +0000 (15:25 +0800)]
drm/amdgpu: add a helper function to decode iv
since from soc15, all the chips share the same
iv format. create a common helper to decode iv
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:30:12 +0000 (23:30 +0800)]
drm/amdgpu: use cached ih rb control reg offsets for navi10
all the ih rb control register offsets are cached
at the beginning of navi10 ih_sw_init.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Wed, 9 Dec 2020 05:36:32 +0000 (13:36 +0800)]
drm/amdgpu: switch to ih_enable_ring for navi10
use navi10_ih_enable_ring to enable all the
available ring buffers for navi1x and onwards
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:23:16 +0000 (23:23 +0800)]
drm/amdgpu: switch to ih_toggle_interrupts for navi10
replace ih_enable_interrupts and ih_disable_interrupts
with ih_toggle_interrupts
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:20:55 +0000 (23:20 +0800)]
drm/amdgpu: switch to ih_init_register_offset for navi10
Initialize ih control registers offset through helper
function navi10_ih_init_register_offset.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:19:03 +0000 (23:19 +0800)]
drm/amdgpu: add helper to toggle ih ring interrupts for navi10
navi10_ih_toggle_ring_interrupts will be used to
enable/disable an ih ring interrupts for navi1x
and onwards
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:17:13 +0000 (23:17 +0800)]
drm/amdgpu: add helper to enable an ih ring for navi10
navi10_ih_enable_ring will be used to enable an
ih ring for navi1x and onwards
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:15:32 +0000 (23:15 +0800)]
drm/amdgpu: add helper to init ih ring regs for navi10
navi10_ih_init_register_offset will be used to init
register offset for all the available ih rings
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Mon, 30 Nov 2020 14:49:40 +0000 (22:49 +0800)]
drm/amdgpu: correct ih cg programming for vega10 ih block
vega10/12 and RAVEN don't support soft override
ih_buffer_mem_clk.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:13:12 +0000 (23:13 +0800)]
drm/amdgpu: use cached ih rb control reg offsets for vega10
all the ih rb control register offsets are cached
at the beginning of ih_sw_init.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 8 Dec 2020 14:10:47 +0000 (22:10 +0800)]
drm/amdgpu: switch to ih_enable_ring for vega10
use vega10_ih_enable_ring to enable all the
available ring buffers for vega10/12, RAVEN
series and RENOIR APUs
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:03:32 +0000 (23:03 +0800)]
drm/amdgpu: switch to ih_toggle_interrupts for vega10
replace ih_enable_interrupts and ih_disable_interrupts
with ih_toggle_interrupts
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 15:01:02 +0000 (23:01 +0800)]
drm/amdgpu: switch to ih_init_register_offset for vega10
Initialize ih control registers offset through helper
function vega10_ih_init_register_offset.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 14:54:47 +0000 (22:54 +0800)]
drm/amdgpu: add helper to toggle ih ring interrupts for vega10
vega10_ih_toggle_ring_interrupts will be used to
enable/disable an ih ring interrupts for vega10/12,
RAVEN series and RENOIR APUs
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 14:53:17 +0000 (22:53 +0800)]
drm/amdgpu: add helper to enable an ih ring for vega10
vega10_ih_enable_ring will be used to enable an
ih ring for vega10/12, RAVEN series and RENOIR.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 14:44:40 +0000 (22:44 +0800)]
drm/amdgpu: add helper to init ih ring regs for vega10
vega10_ih_init_register_offset will be used to init
register offset for all the available ih rings
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hawking Zhang [Tue, 1 Dec 2020 14:36:46 +0000 (22:36 +0800)]
drm/amdgpu: add amdgpu_ih_regs structure
amdgpu_ih_regs holds all the registers for
an ih ring
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Dennis Li <Dennis.Li@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stylon Wang [Tue, 10 Nov 2020 07:40:06 +0000 (15:40 +0800)]
drm/amd/display: Fix memory leaks in S3 resume
EDID parsing in S3 resume pushes new display modes
to probed_modes list but doesn't consolidate to actual
mode list. This creates a race condition when
amdgpu_dm_connector_ddc_get_modes() re-initializes the
list head without walking the list and results in memory leak.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209987 Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
Alex Deucher [Thu, 17 Dec 2020 17:11:36 +0000 (12:11 -0500)]
drm/amdgpu: only set DP subconnector type on DP and eDP connectors
Fixes a crash in drm_object_property_set_value() because the property
is not set for internal DP ports that connect to a bridge chips
(e.g., DP to VGA or DP to LVDS).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=210739 Fixes: 65bf2cf95d3ade ("drm/amdgpu: utilize subconnector property for DP through atombios") Tested-By: Kris Karas <bugs-a17@moonlit-rail.com> Cc: Oleg Vasilev <oleg.vasilev@intel.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 5.10.x
Jake Wang [Fri, 11 Dec 2020 21:53:57 +0000 (16:53 -0500)]
drm/amd/display: always program DPPDTO unless not safe to lower
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com> Acked-by: Bindu Ramamurthy <bindu.r@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Fri, 11 Dec 2020 20:34:30 +0000 (15:34 -0500)]
drm/amd/display: [FW Promotion] Release 0.0.47
- restore lvtma_pwrseq_delay2 from vbios integrated info table
- restore MVID/NVID after power up.
- Enable timer wake up mask when enable timer interrupt.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Bindu Ramamurthy <bindu.r@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sung Lee [Wed, 9 Dec 2020 19:58:59 +0000 (14:58 -0500)]
drm/amd/display: Acquire DSC during split stream for ODM only if top_pipe
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com> Acked-by: Bindu Ramamurthy <bindu.r@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yongqiang Sun [Wed, 9 Dec 2020 21:56:51 +0000 (16:56 -0500)]
drm/amd/display: change SMU repsonse timeout to 2s.
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com> Acked-by: Bindu Ramamurthy <bindu.r@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Martin Tsai [Thu, 3 Dec 2020 02:47:11 +0000 (10:47 +0800)]
drm/amd/display: Modify the hdcp device count check condition
[why]
Some MST display may not report the internal panel to DEVICE_COUNT,
that makes the check condition always failed.
[how]
To update this condition with the reported device count + 1
(because the immediate repeater's internal panel is possibly
not included in DEVICE_COUNT)
Signed-off-by: Martin Tsai <martin.tsai@amd.com> Acked-by: Bindu Ramamurthy <bindu.r@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wesley Chalmers [Mon, 7 Dec 2020 16:46:08 +0000 (11:46 -0500)]
drm/amd/display: Interfaces for hubp blank and soft reset
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Qingqing Zhuo [Fri, 4 Dec 2020 15:55:13 +0000 (10:55 -0500)]
drm/amd/display: handler not correctly checked at remove_irq_handler
[why]
handler is supposedly passed in as a function pointer;
however, the entire struct amdgpu_dm_irq_handler_data
gets from the list is used to check match.
[how]
use the interrupt_handler within amdgpu_dm_irq_handler_data
for checking match.
projects / mirror_ubuntu-kernels.git / log