Add support for platforms where pit_shutdown() doesn't work because of a
quirk in the PIT emulation. On these platforms setting the counter register
to zero causes the PIT to start running again, negating the shutdown.
Provide a global variable that controls whether the counter register is
zero'ed, which platform specific code can override.
We currently allow cloning a range from a file which includes the last
block of the file even if the file's size is not aligned to the block
size. This is fine and useful when the destination file has the same size,
but when it does not and the range ends somewhere in the middle of the
destination file, it leads to corruption because the bytes between the EOF
and the end of the block have undefined data (when there is support for
discard/trimming they have a value of 0x00).
The bytes in the range from 786532 (512Kb + 256Kb + 100 bytes) to 790527
(512Kb + 256Kb + 4Kb - 1) got corrupted, having now a value of 0x00 instead
of 0xb5.
This is similar to the problem we had for deduplication that got recently
fixed by commit de02b9f6bb65 ("Btrfs: fix data corruption when
deduplicating between different files").
Fix this by not allowing such operations to be performed and return the
errno -EINVAL to user space. This is what XFS is doing as well at the VFS
level. This change however now makes us return -EINVAL instead of
-EOPNOTSUPP for cases where the source range maps to an inline extent and
the destination range's end is smaller then the destination file's size,
since the detection of inline extents is done during the actual process of
dropping file extent items (at __btrfs_drop_extents()). Returning the
-EINVAL error is done early on and solely based on the input parameters
(offsets and length) and destination file's size. This makes us consistent
with XFS and anyone else supporting cloning since this case is now checked
at a higher level in the VFS and is where the -EINVAL will be returned
from starting with kernel 4.20 (the VFS changed was introduced in 4.20-rc1
by commit 07d19dc9fbe9 ("vfs: avoid problematic remapping requests into
partial EOF block"). So this change is more geared towards stable kernels,
as it's unlikely the new VFS checks get removed intentionally.
A test case for fstests follows soon, as well as an update to filter
existing tests that expect -EOPNOTSUPP to accept -EINVAL as well.
CC: <stable@vger.kernel.org> # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we attempt to deduplicate the last block of a file A into the middle of
a file B, and file A's size is not a multiple of the block size, we end
rounding the deduplication length to 0 bytes, to avoid the data corruption
issue fixed by commit de02b9f6bb65 ("Btrfs: fix data corruption when
deduplicating between different files"). However a length of zero will
cause the insertion of an extent state with a start value greater (by 1)
then the end value, leading to a corrupt extent state that will trigger a
warning and cause chaos such as an infinite loop during inode eviction.
Example trace:
The second stack trace, from inode eviction, is repeated forever due to
the infinite loop during eviction.
This is the same type of problem fixed way back in 2015 by commit 113e8283869b ("Btrfs: fix inode eviction infinite loop after extent_same
ioctl") and commit ccccf3d67294 ("Btrfs: fix inode eviction infinite loop
after cloning into it").
So fix this by returning immediately if the deduplication range length
gets rounded down to 0 bytes, as there is nothing that needs to be done in
such case.
# Unmount the filesystem and mount it again so that we start without any
# extent state records when we ask for the deduplication.
$ umount /mnt
$ mount /dev/sdb /mnt
$ xfs_io -c "dedupe /mnt/foo 0 500K 100" /mnt/bar
# This unmount triggers the infinite loop.
$ umount /mnt
A test case for fstests will follow soon.
Fixes: de02b9f6bb65 ("Btrfs: fix data corruption when deduplicating between different files") CC: <stable@vger.kernel.org> # 4.19+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the cow_file_range fails, the related resources are unlocked
according to the range [start..end), so the unlock cannot be repeated in
run_delalloc_nocow.
In some cases (e.g. cur_offset <= end && cow_start != -1), cur_offset is
not updated correctly, so move the cur_offset update before
cow_file_range.
In the above line there's "pinned=18446744073708158976" which is an
unsigned u64 value of -1392640, an obvious underflow.
When transaction_kthread is running cleanup_transaction(), another
fsstress is running btrfs_commit_transaction(). The
btrfs_finish_extent_commit() may get the same range as
btrfs_destroy_pinned_extent() got, which causes the pinned underflow.
Fixes: d4b450cd4b33 ("Btrfs: fix race between transaction commit and empty block group removal") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The split out of the hard lockup detector exposed two new weak functions,
but no prototypes for them, which triggers the build warning:
kernel/watchdog.c:109:12: warning: no previous prototype for ‘watchdog_nmi_enable’ [-Wmissing-prototypes]
kernel/watchdog.c:115:13: warning: no previous prototype for ‘watchdog_nmi_disable’ [-Wmissing-prototypes]
Add the prototypes.
Fixes: 73ce0511c436 ("kernel/watchdog.c: move hardlockup detector to separate file") Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Babu Moger <babu.moger@oracle.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180606194232.17653-1-malat@debian.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Alpha has had c_ispeed and c_ospeed, but still set speeds in c_cflags
using arbitrary flags. Because BOTHER is not defined, the general
Linux code doesn't allow setting arbitrary baud rates, and because
CBAUDEX == 0, we can have an array overrun of the baud_rate[] table in
drivers/tty/tty_baudrate.c if (c_cflags & CBAUD) == 037.
Resolve both problems by #defining BOTHER to 037 on Alpha.
However, userspace still needs to know if setting BOTHER is actually
safe given legacy kernels (does anyone actually care about that on
Alpha anymore?), so enable the TCGETS2/TCSETS*2 ioctls on Alpha, even
though they use the same structure. Define struct termios2 just for
compatibility; it is the exact same structure as struct termios. In a
future patchset, this will be cleaned up so the uapi headers are
usable from libc.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Eugene Syromiatnikov <esyr@redhat.com> Cc: <linux-alpha@vger.kernel.org> Cc: <linux-serial@vger.kernel.org> Cc: Johan Hovold <johan@kernel.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On architectures with CBAUDEX == 0 (Alpha and PowerPC), the code in tty_baudrate.c does
not do any limit checking on the tty_baudrate[] array, and in fact a
buffer overrun is possible on both architectures. Add a limit check to
prevent that situation.
This will be followed by a much bigger cleanup/simplification patch.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com> Requested-by: Cc: Johan Hovold <johan@kernel.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Eugene Syromiatnikov <esyr@redhat.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Hyper-V emulation of the PIT has a quirk such that the normal PIT shutdown
path doesn't work, because clearing the counter register restarts the
timer.
When running function tracing on a Linux guest running on VMware
Workstation, the guest would crash. This is due to tracing of the
sched_clock internal call of the VMware vmware_sched_clock(), which
causes an infinite recursion within the tracing code (clock calls must
not be traced).
Currently the NUMA distance map parsing does not validate the distance
table for the distance-matrix rules 1-2 in [1].
However the arch NUMA code may enforce some of these rules, but not all.
Such is the case for the arm64 port, which does not enforce the rule that
the distance between separates nodes cannot equal LOCAL_DISTANCE.
The patch adds the following rules validation:
- distance of node to self equals LOCAL_DISTANCE
- distance of separate nodes > LOCAL_DISTANCE
This change avoids a yet-unresolved crash reported in [2].
A note on dealing with symmetrical distances between nodes:
Validating symmetrical distances between nodes is difficult. If it were
mandated in the bindings that every distance must be recorded in the
table, then it would be easy. However, it isn't.
In addition to this, it is also possible to record [b, a] distance only
(and not [a, b]). So, when processing the table for [b, a], we cannot
assert that current distance of [a, b] != [b, a] as invalid, as [a, b]
distance may not be present in the table and current distance would be
default at REMOTE_DISTANCE.
As such, we maintain the policy that we overwrite distance [a, b] = [b, a]
for b > a. This policy is different to kernel ACPI SLIT validation, which
allows non-symmetrical distances (ACPI spec SLIT rules allow it). However,
the distance debug message is dropped as it may be misleading (for a distance
which is later overwritten).
Some final notes on semantics:
- It is implied that it is the responsibility of the arch NUMA code to
reset the NUMA distance map for an error in distance map parsing.
- It is the responsibility of the FW NUMA topology parsing (whether OF or
ACPI) to enforce NUMA distance rules, and not arch NUMA code.
I noticed during the creation of another bugfix that the BCH_CONST_PARAMS
option that is set by DOCG3 breaks setting variable parameters for any
other users of the BCH library code.
The only other user we have today is the MTD_NAND software BCH
implementation (most flash controllers use hardware BCH these days
and are not affected). I considered removing BCH_CONST_PARAMS entirely
because of the inherent conflict, but according to the description in
lib/bch.c there is a significant performance benefit in keeping it.
To avoid the immediate problem of the conflict between MTD_NAND_BCH
and DOCG3, this only sets the constant parameters if MTD_NAND_BCH
is disabled, which should fix the problem for all cases that
are affected. This should also work for all stable kernels.
Note that there is only one machine that actually seems to use the
DOCG3 driver (arch/arm/mach-pxa/mioa701.c), so most users should have
the driver disabled, but it almost certainly shows up if we wanted
to test random kernels on machines that use software BCH in MTD.
Due to what appears to be a copy/paste error, the opening ENTRY()
of cpu_v7_hvc_switch_mm() lacks a matching ENDPROC(), and instead,
the one for cpu_v7_smc_switch_mm() is duplicated.
Given that it is ENDPROC() that emits the Thumb annotation, the
cpu_v7_hvc_switch_mm() routine will be called in ARM mode on a
Thumb2 kernel, resulting in the following splat:
If there's no entry to drop in bucket that corresponds to the hash,
early_drop() should look for it in other buckets. But since it increments
hash instead of bucket number, it actually looks in the same bucket 8
times: hsize is 16k by default (14 bits) and hash is 32-bit value, so
reciprocal_scale(hash, hsize) returns the same value for hash..hash+7 in
most cases.
Fix it by increasing bucket number instead of hash and rename _hash
to bucket to avoid future confusion.
THP allocation might be really disruptive when allocated on NUMA system
with the local node full or hard to reclaim. Stefan has posted an
allocation stall report on 4.12 based SLES kernel which suggests the
same issue:
The defrag mode is "madvise" and from the above report it is clear that
the THP has been allocated for MADV_HUGEPAGA vma.
Andrea has identified that the main source of the problem is
__GFP_THISNODE usage:
: The problem is that direct compaction combined with the NUMA
: __GFP_THISNODE logic in mempolicy.c is telling reclaim to swap very
: hard the local node, instead of failing the allocation if there's no
: THP available in the local node.
:
: Such logic was ok until __GFP_THISNODE was added to the THP allocation
: path even with MPOL_DEFAULT.
:
: The idea behind the __GFP_THISNODE addition, is that it is better to
: provide local memory in PAGE_SIZE units than to use remote NUMA THP
: backed memory. That largely depends on the remote latency though, on
: threadrippers for example the overhead is relatively low in my
: experience.
:
: The combination of __GFP_THISNODE and __GFP_DIRECT_RECLAIM results in
: extremely slow qemu startup with vfio, if the VM is larger than the
: size of one host NUMA node. This is because it will try very hard to
: unsuccessfully swapout get_user_pages pinned pages as result of the
: __GFP_THISNODE being set, instead of falling back to PAGE_SIZE
: allocations and instead of trying to allocate THP on other nodes (it
: would be even worse without vfio type1 GUP pins of course, except it'd
: be swapping heavily instead).
Fix this by removing __GFP_THISNODE for THP requests which are
requesting the direct reclaim. This effectivelly reverts 5265047ac301
on the grounds that the zone/node reclaim was known to be disruptive due
to premature reclaim when there was memory free. While it made sense at
the time for HPC workloads without NUMA awareness on rare machines, it
was ultimately harmful in the majority of cases. The existing behaviour
is similar, if not as widespare as it applies to a corner case but
crucially, it cannot be tuned around like zone_reclaim_mode can. The
default behaviour should always be to cause the least harm for the
common case.
If there are specialised use cases out there that want zone_reclaim_mode
in specific cases, then it can be built on top. Longterm we should
consider a memory policy which allows for the node reclaim like behavior
for the specific memory ranges which would allow a
: Both patches look correct to me but I'm responding to this one because
: it's the fix. The change makes sense and moves further away from the
: severe stalling behaviour we used to see with both THP and zone reclaim
: mode.
:
: I put together a basic experiment with usemem configured to reference a
: buffer multiple times that is 80% the size of main memory on a 2-socket
: box with symmetric node sizes and defrag set to "always". The defrag
: setting is not the default but it would be functionally similar to
: accessing a buffer with madvise(MADV_HUGEPAGE). Usemem is configured to
: reference the buffer multiple times and while it's not an interesting
: workload, it would be expected to complete reasonably quickly as it fits
: within memory. The results were;
:
: usemem
: vanilla noreclaim-v1
: Amean Elapsd-1 42.78 ( 0.00%) 26.87 ( 37.18%)
: Amean Elapsd-3 27.55 ( 0.00%) 7.44 ( 73.00%)
: Amean Elapsd-4 5.72 ( 0.00%) 5.69 ( 0.45%)
:
: This shows the elapsed time in seconds for 1 thread, 3 threads and 4
: threads referencing buffers 80% the size of memory. With the patches
: applied, it's 37.18% faster for the single thread and 73% faster with two
: threads. Note that 4 threads showing little difference does not indicate
: the problem is related to thread counts. It's simply the case that 4
: threads gets spread so their workload mostly fits in one node.
:
: The overall view from /proc/vmstats is more startling
:
: 4.19.0-rc1 4.19.0-rc1
: vanillanoreclaim-v1r1
: Minor Faults 35593425 708164
: Major Faults 484088 36
: Swap Ins 3772837 0
: Swap Outs 3932295 0
:
: Massive amounts of swap in/out without the patch
:
: Direct pages scanned 6013214 0
: Kswapd pages scanned 0 0
: Kswapd pages reclaimed 0 0
: Direct pages reclaimed 4033009 0
:
: Lots of reclaim activity without the patch
:
: Kswapd efficiency 100% 100%
: Kswapd velocity 0.000 0.000
: Direct efficiency 67% 100%
: Direct velocity 11191.956 0.000
:
: Mostly from direct reclaim context as you'd expect without the patch.
:
: Page writes by reclaim 3932314.000 0.000
: Page writes file 19 0
: Page writes anon 3932295 0
: Page reclaim immediate 42336 0
:
: Writes from reclaim context is never good but the patch eliminates it.
:
: We should never have default behaviour to thrash the system for such a
: basic workload. If zone reclaim mode behaviour is ever desired but on a
: single task instead of a global basis then the sensible option is to build
: a mempolicy that enforces that behaviour.
This was a severe regression compared to previous kernels that made
important workloads unusable and it starts when __GFP_THISNODE was
added to THP allocations under MADV_HUGEPAGE. It is not a significant
risk to go to the previous behavior before __GFP_THISNODE was added, it
worked like that for years.
This was simply an optimization to some lucky workloads that can fit in
a single node, but it ended up breaking the VM for others that can't
possibly fit in a single node, so going back is safe.
[mhocko@suse.com: rewrote the changelog based on the one from Andrea] Link: http://lkml.kernel.org/r/20180925120326.24392-2-mhocko@kernel.org Fixes: 5265047ac301 ("mm, thp: really limit transparent hugepage allocation to local node") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Stefan Priebe <s.priebe@profihost.ag> Debugged-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: Mel Gorman <mgorman@techsingularity.net> Tested-by: Mel Gorman <mgorman@techsingularity.net> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: <stable@vger.kernel.org> [4.1+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The write context should also be freed even when direct IO failed.
Otherwise a memory leak is introduced and entries remain in
oi->ip_unwritten_list causing the following BUG later in unlink path:
Somehow, file system metadata was corrupted, which causes
ocfs2_check_dir_entry() to fail in function ocfs2_dir_foreach_blk_el().
According to the original design intention, if above happens we should
skip the problematic block and continue to retrieve dir entry. But
there is obviouse misuse of brelse around related code.
After failure of ocfs2_check_dir_entry(), current code just moves to
next position and uses the problematic buffer head again and again
during which the problematic buffer head is released for multiple times.
I suppose, this a serious issue which is long-lived in ocfs2. This may
cause other file systems which is also used in a the same host insane.
So we should also consider about bakcporting this patch into linux
-stable.
Link: http://lkml.kernel.org/r/HK2PR06MB045211675B43EED794E597B6D56E0@HK2PR06MB0452.apcprd06.prod.outlook.com Signed-off-by: Changwei Ge <ge.changwei@h3c.com> Suggested-by: Changkuo Shi <shi.changkuo@h3c.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Keystone QMSS driver is pretty damaged, in the sense that it
does things like this:
irq_set_affinity_hint(irq, to_cpumask(&cpu_map));
where cpu_map is a local variable. As we leave the function, this
will point to nowhere-land, and things will end-up badly.
Instead, let's use a proper cpumask that gets allocated, giving
the driver a chance to actually work with things like irqbalance
as well as have a hypothetical 64bit future.
Cc: stable@vger.kernel.org Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
c2856ae2f315d ("blk-mq: quiesce queue before freeing queue") has
already fixed this race, however the implied synchronize_rcu()
in blk_mq_quiesce_queue() can slow down LUN probe a lot, so caused
performance regression.
Then 1311326cf4755c7 ("blk-mq: avoid to synchronize rcu inside blk_cleanup_queue()")
tried to quiesce queue for avoiding unnecessary synchronize_rcu()
only when queue initialization is done, because it is usual to see
lots of inexistent LUNs which need to be probed.
However, turns out it isn't safe to quiesce queue only when queue
initialization is done. Because when one SCSI command is completed,
the user of sending command can be waken up immediately, then the
scsi device may be removed, meantime the run queue in scsi_end_request()
is still in-progress, so kernel panic can be caused.
In Red Hat QE lab, there are several reports about this kind of kernel
panic triggered during kernel booting.
This patch tries to address the issue by grabing one queue usage
counter during freeing one request and the following run queue.
Fixes: 1311326cf4755c7 ("blk-mq: avoid to synchronize rcu inside blk_cleanup_queue()") Cc: Andrew Jones <drjones@redhat.com> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: linux-scsi@vger.kernel.org Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com> Cc: stable <stable@vger.kernel.org> Cc: jianchao.wang <jianchao.w.wang@oracle.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commands with protection information included were not truncating the
protection iov_iter to the number of protection bytes in the command.
This resulted in vhost_scsi mis-calculating the size of the protection
SGL in vhost_scsi_calc_sgls(), and including both the protection and
data SG entries in the protection SGL.
Fixes: 09b13fa8c1a1 ("vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq") Signed-off-by: Greg Edwards <gedwards@ddn.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Fixes: 09b13fa8c1a1093e9458549ac8bb203a7c65c62a Cc: stable@vger.kernel.org Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is a potential execution path in which function
platform_get_resource() returns NULL. If this happens,
we will end up having a NULL pointer dereference.
Fix this by replacing devm_ioremap with devm_ioremap_resource,
which has the NULL check and the memory region request.
This code was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org Fixes: 97b7129cd2af ("reset: hisilicon: change the definition of hisi_reset_init") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Reading the registers without waiting for engine idle returns
unpredictable values. These unpredictable values result in display
corruption - if atyfb_imageblit reads the content of DP_PIX_WIDTH with the
bit DP_HOST_TRIPLE_EN set (from previous invocation), the driver would
never ever clear the bit, resulting in display corruption.
We don't want to wait for idle because it would degrade performance, so
this patch modifies the driver so that it never reads accelerator
registers.
HOST_CNTL doesn't have to be read, we can just write it with
HOST_BYTE_ALIGN because no other part of the driver cares if
HOST_BYTE_ALIGN is set.
DP_PIX_WIDTH is written in the functions atyfb_copyarea and atyfb_fillrect
with the default value and in atyfb_imageblit with the value set according
to the source image data.
The code for manual bit triple is not endian-clean. It builds the variable
"hostdword" using byte accesses, therefore we must read the variable with
"le32_to_cpu".
The patch also enables (hardware or software) bit triple only if the image
is monochrome (image->depth). If we want to blit full-color image, we
shouldn't use the triple code.
Fixes the signedness bug returning '(-22)' on the return type by removing the
sanity checker in rockchip_ddrclk_get_parent(). The function should return
and unsigned value only and it's safe to remove the sanity checker as the
core functions that call get_parent like clk_core_get_parent_by_index already
ensures the validity of the clk index returned (index >= core->num_parents).
Fixes: a4f182bf81f18 ("clk: rockchip: add new clock-type for the ddrclk") Cc: stable@vger.kernel.org Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit a982e45dc150 ("clk: at91: PLL recalc_rate() now using cached MUL
and DIV values") removed a check that prevents a division by zero. This
now causes a stacktrace when booting the kernel on a at91 platform if
the PLL DIV register contains zero. This commit reintroduces this check.
Fixes: a982e45dc150 ("clk: at91: PLL recalc_rate() now using cached...") Cc: <stable@vger.kernel.org> Signed-off-by: Ronald Wahl <rwahl@gmx.de> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When driver is built as module and DT node contains clocks compatible
(e.g. "samsung,s2mps11-clk"), the module will not be autoloaded because
module aliases won't match.
The modalias from uevent: of:NclocksT<NULL>Csamsung,s2mps11-clk
The modalias from driver: platform:s2mps11-clk
The devices are instantiated by parent's MFD. However both Device Tree
bindings and parent define the compatible for clocks devices. In case
of module matching this DT compatible will be used.
The issue will not happen if this is a built-in (no need for module
matching) or when clocks DT node does not contain compatible (not
correct from bindings perspective but working for driver).
Note when backporting to stable kernels: adjust the list of device ID
entries.
Cc: <stable@vger.kernel.org> Fixes: 53c31b3437a6 ("mfd: sec-core: Add of_compatible strings for clock MFD cells") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
32bit UML used to define PTRACE_SYSEMU and PTRACE_SYSEMU_SINGLESTEP
own its own because many years ago not all libcs had these request codes
in their UAPI.
These days PTRACE_SYSEMU/_SINGLESTEP is well known and part of glibc
and our own define becomes problematic.
With change c48831d0eebf ("linux/x86: sync sys/ptrace.h with Linux 4.14
[BZ #22433]") glibc turned PTRACE_SYSEMU/_SINGLESTEP into a enum and
UML failed to build.
Let's drop our define and rely on the fact that every libc has
PTRACE_SYSEMU/_SINGLESTEP.
The bootloader may pass physical address of the boot parameters structure
to the MMUv3 kernel in the register a2. Code in the _SetupMMU block in
the arch/xtensa/kernel/head.S is supposed to map that physical address to
the virtual address in the configured virtual memory layout.
This code haven't been updated when additional 256+256 and 512+512
memory layouts were introduced and it may produce wrong addresses when
used with these layouts.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Xtensa ABI requires stack alignment to be at least 16. In noMMU
configuration ARCH_SLAB_MINALIGN is used to align stack. Make it at
least 16.
This fixes the following runtime error in noMMU configuration, caused by
interaction between insufficiently aligned stack and alloca function,
that results in corruption of on-stack variable in the libc function
glob:
Caught unhandled exception in 'sh' (pid = 47, pc = 0x02d05d65)
- should not happen
EXCCAUSE is 15
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This section collects all source .note.* sections together in the
vmlinux image. Without it .note.Linux section may be placed at address
0, while the rest of the kernel is at its normal address, resulting in a
huge vmlinux.bin image that may not be linked into the xtensa Image.elf.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After commit e509bd7da149dc349160 ("genirq: Allow migration of chained
interrupts by installing default action") Loongson-3 fails at here:
setup_irq(LOONGSON_HT1_IRQ, &cascade_irqaction);
This is because both chained_action and cascade_irqaction don't have
IRQF_SHARED flag. This will cause Loongson-3 resume fails because HPET
timer interrupt can't be delivered during S3. So we set the irqchip of
the chained irq to loongson_irq_chip which doesn't disable the chained
irq in CP0.Status.
Masking/unmasking the CPU UART irq in CP0_Status (and redirecting it to
other CPUs) may cause interrupts be lost, especially in multi-package
machines (Package-0's UART irq cannot be delivered to others). So make
mask_loongson_irq() and unmask_loongson_irq() be no-ops.
The original problem (UART IRQ may deliver to any core) is also because
of masking/unmasking the CPU UART irq in CP0_Status. So it is safe to
remove all of the stuff.
linking a non-copied-up file into a non-copied-up parent results in a
nested call to mutex_lock_interruptible(&oi->lock). Fix this by copying up
target parent before ovl_nlink_start(), same as done in ovl_rename().
This patch fixes issue where driver clears NPort ID map instead of marking
handle in use. Once driver clears NPort ID from the database, it can reuse
the same NPort ID resulting in a PLOGI failure.
[mkp: fixed Himanshu's SoB]
Fixes: a084fd68e1d2 ("scsi: qla2xxx: Fix re-login for Nport Handle in use") Cc: <stable@vger.kernel.org> Signed-of-by: Quinn Tran <quinn.tran@cavium.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Himanshu Madhani <hmadhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
p9stat_free is more of a cleanup function than a 'free' function as it
only frees the content of the struct; there are chances of use-after-free
if it is improperly used (e.g. p9stat_free called twice as it used to be
possible to)
Clearing dangling pointers makes the function idempotent and safer to use.
the 9p client code overwrites our glock.client_id pointing to a static
buffer by an allocated string holding the network provided value which
we do not care about; free and reset the value as appropriate.
This is almost identical to the leak in v9fs_file_getlock() fixed by
Al Viro in commit ce85dd58ad5a6 ("9p: we are leaking glock.client_id
in v9fs_file_getlock()"), which was returned as an error by a coverity
false positive -- while we are here attempt to make the code slightly
more robust to future change of the net/9p/client code and hopefully
more clear to coverity that there is no problem.
The AD7606 devices don't have a 2.5V voltage range, they have 5V & 10V
voltage range, which is selectable via the `gpio_range` descriptor.
The scales also seem to have been miscomputed, because when they were
applied to the raw values, the results differ from the expected values.
After checking the ADC transfer function in the datasheet, these were
re-computed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver ignored the width alignment which exists due to the UYVY
colorspace format. Fix the width alignment and make use of the the
provided v4l2 helper function to set the width, height and all
alignments in one.
The SC16IS752 is a dual-channel device. The two channels are largely
independent, but the IRQ signals are wired together as an open-drain,
active low signal which will be driven low while either of the
channels requires attention, which can be for significant periods of
time until operations complete and the interrupt can be acknowledged.
In that respect it is should be treated as a true level-sensitive IRQ.
The kernel, however, needs to be able to exit interrupt context in
order to use I2C or SPI to access the device registers (which may
involve sleeping). Therefore the interrupt needs to be masked out or
paused in some way.
The usual way to manage sleeping from within an interrupt handler
is to use a threaded interrupt handler - a regular interrupt routine
does the minimum amount of work needed to triage the interrupt before
waking the interrupt service thread. If the threaded IRQ is marked as
IRQF_ONESHOT the kernel will automatically mask out the interrupt
until the thread runs to completion. The sc16is7xx driver used to
use a threaded IRQ, but a patch switched to using a kthread_worker
in order to set realtime priorities on the handler thread and for
other optimisations. The end result is non-threaded IRQ that
schedules some work then returns IRQ_HANDLED, making the kernel
think that all IRQ processing has completed.
The work-around to prevent a constant stream of interrupts is to
mark the interrupt as edge-sensitive rather than level-sensitive,
but interpreting an active-low source as a falling-edge source
requires care to prevent a total cessation of interrupts. Whereas
an edge-triggering source will generate a new edge for every interrupt
condition a level-triggering source will keep the signal at the
interrupting level until it no longer requires attention; in other
words, the host won't see another edge until all interrupt conditions
are cleared. It is therefore vital that the interrupt handler does not
exit with an outstanding interrupt condition, otherwise the kernel
will not receive another interrupt unless some other operation causes
the interrupt state on the device to be cleared.
The existing sc16is7xx driver has a very simple interrupt "thread"
(kthread_work job) that processes interrupts on each channel in turn
until there are no more. If both channels are active and the first
channel starts interrupting while the handler for the second channel
is running then it will not be detected and an IRQ stall ensues. This
could be handled easily if there was a shared IRQ status register, or
a convenient way to determine if the IRQ had been deasserted for any
length of time, but both appear to be lacking.
Avoid this problem (or at least make it much less likely to happen)
by reducing the granularity of per-channel interrupt processing
to one condition per iteration, only exiting the overall loop when
both channels are no longer interrupting.
Call pcie_bus_configure_settings() on MIPS, like for other platforms.
The function pcie_bus_configure_settings() makes sure the MPS (Max
Payload Size) across the bus is uniform and provides the ability to
tune the MRSS (Max Read Request Size) and MPS (Max Payload Size) to
higher performance values. Some devices will not operate properly if
these aren't set correctly because the firmware doesn't always do it.
When hot-removing memory release_mem_region_adjustable() splits iomem
resources if they are not the exact size of the memory being
hot-deleted. Adding this memory back to the kernel adds a new resource.
Eg a node has memory 0x0 - 0xfffffffff. Hot-removing 1GB from
0xf40000000 results in the single resource 0x0-0xfffffffff being split
into two resources: 0x0-0xf3fffffff and 0xf80000000-0xfffffffff.
When we hot-add the memory back we now have three resources:
0x0-0xf3fffffff, 0xf40000000-0xf7fffffff, and 0xf80000000-0xfffffffff.
This is an issue if we try to remove some memory that overlaps
resources. Eg when trying to remove 2GB at address 0xf40000000,
release_mem_region_adjustable() fails as it expects the chunk of memory
to be within the boundaries of a single resource. We then get the
warning: "Unable to release resource" and attempting to use memtrace
again gives us this error: "bash: echo: write error: Resource
temporarily unavailable"
This patch makes memtrace remove memory in chunks that are always the
same size from an address that is always equal to end_of_memory -
n*size, for some n. So hotremoving and hotadding memory of different
sizes will now not attempt to remove memory that spans multiple
resources.
ld: arch/powerpc/boot/wrapper.a(crt0.o): in function '_zimage_start':
(.text+0x58): multiple definition of '_zimage_start';
arch/powerpc/boot/pseries-head.o:(.text+0x0): first defined here
Clang requires the .weak directive to appear after the symbol is
declared. The binutils manual says:
This directive sets the weak attribute on the comma separated list of
symbol names. If the symbols do not already exist, they will be
created.
So it appears this is different with clang. The only reference I could
see for this was an OpenBSD mailing list post[1].
Changing it to be after the declaration fixes building with Clang, and
still works with GCC.
After changing CPU online status, it will not be sent any IPIs such as in
__flush_cache_all() on software coherency systems. Do this before disabling
local IRQ.
On a decoder instance, after the profile has been parsed from the stream
__v4l2_ctrl_s_ctrl() is called to notify userspace about changes in the
read-only profile control. This ends up calling back into the CODA driver
where a missing check on the s_ctrl caused the profile information that has
just been parsed from the stream to be overwritten with the default
baseline profile.
Later on the driver fails to enable frame reordering, based on the wrong
profile information.
altera_hw_filt_init() which calls append_internal() assumes
that the node was successfully linked in while in fact it can
silently fail. So the call-site needs to set return to -ENOMEM
on append_internal() returning NULL and exit through the err path.
Fixes: 349bcf02e361 ("[media] Altera FPGA based CI driver module") Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In hibmc_drm_fb_create(), when the call to hibmc_framebuffer_init() fails
with error, do not store the error code in the HiBMC device frame-buffer
pointer, as this will be later checked for non-zero value in
hibmc_fbdev_destroy() when our intention is to check for a valid function
pointer.
A DMM timeout "timed out waiting for done" has been observed on DRA7
devices. The timeout happens rarely, and only when the system is under
heavy load.
Debugging showed that the timeout can be made to happen much more
frequently by optimizing the DMM driver, so that there's almost no code
between writing the last DMM descriptors to RAM, and writing to DMM
register which starts the DMM transaction.
The current theory is that a wmb() does not properly ensure that the
data written to RAM is observable by all the components in the system.
This DMM timeout has caused interesting (and rare) bugs as the error
handling was not functioning properly (the error handling has been fixed
in previous commits):
* If a DMM timeout happened when a GEM buffer was being pinned for
display on the screen, a timeout error would be shown, but the driver
would continue programming DSS HW with broken buffer, leading to
SYNCLOST floods and possible crashes.
* If a DMM timeout happened when other user (say, video decoder) was
pinning a GEM buffer, a timeout would be shown but if the user
handled the error properly, no other issues followed.
* If a DMM timeout happened when a GEM buffer was being released, the
driver does not even notice the error, leading to crashes or hang
later.
This patch adds wmb() and readl() calls after the last bit is written to
RAM, which should ensure that the execution proceeds only after the data
is actually in RAM, and thus observable by DMM.
The read-back should not be needed. Further study is required to understand
if DMM is somehow special case and read-back is ok, or if DRA7's memory
barriers do not work correctly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When a process allocates a hugepage, the following leak is
reported by kmemleak. This is a false positive which is
due to the pointer to the table being stored in the PGD
as physical memory address and not virtual memory pointer.
When enumerating page size definitions to check hardware support,
we construct a constant which is (1U << (def->shift - 10)).
However, the array of page size definitions is only initalised for
various MMU_PAGE_* constants, so it contains a number of 0-initialised
elements with def->shift == 0. This means we end up shifting by a
very large number, which gives the following UBSan splat:
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[220]: Failed to apply ACL on /dev/v4l-subdev0: Operation not supported
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[224]: Failed to apply ACL on /dev/v4l-subdev1: Operation not supported
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[215]: Failed to apply ACL on /dev/v4l-subdev10: Operation not supported
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[228]: Failed to apply ACL on /dev/v4l-subdev2: Operation not supported
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[232]: Failed to apply ACL on /dev/v4l-subdev5: Operation not supported
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[217]: Failed to apply ACL on /dev/v4l-subdev11: Operation not supported
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[214]: Failed to apply ACL on /dev/dri/card1: Operation not supported
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[216]: Failed to apply ACL on /dev/v4l-subdev8: Operation not supported
| Sep 04 09:05:10 imx6qdl-variscite-som systemd-udevd[226]: Failed to apply ACL on /dev/v4l-subdev9: Operation not supported
and nasty follow-ups: Starting weston from sddm as unpriviledged user fails
with some hints on missing access rights."
Select the CONFIG_TMPFS_POSIX_ACL option to fix these issues.
The issue is found by a fuzzing test.
If tty_find_polling_driver() recevies an incorrect input such as
',,' or '0b', the len becomes 0 and strncmp() always return 0.
In this case, a null p->ops->poll_init() is called and it causes a kernel
panic.
Fix this by checking name length against zero in tty_find_polling_driver().
If an error occurs during an unplug operation, it's possible for
eeh_dump_dev_log() to be called when edev->pdn is null, which
currently leads to dereferencing a null pointer.
Handle this by skipping the error log for those devices.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we're running on Book3S with the Radix MMU enabled the page table
dump currently prints the wrong addresses because it uses the wrong
start address.
Fix it to use PAGE_OFFSET rather than KERN_VIRT_START.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The recent module relocation overflow crash demonstrated that we
have no range checking on REL32 relative relocations. This patch
implements a basic check, the same kernel that previously oopsed
and rebooted now continues with some of these errors when loading
the module:
commit b96672dd840f ("powerpc: Machine check interrupt is a non-
maskable interrupt") added a call to nmi_enter() at the beginning of
machine check restart exception handler. Due to that, in_interrupt()
always returns true regardless of the state before entering the
exception, and die() panics even when the system was not already in
interrupt.
This patch calls nmi_exit() before calling die() in order to restore
the interrupt state we had before calling nmi_enter()
Fixes: b96672dd840f ("powerpc: Machine check interrupt is a non-maskable interrupt") Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We were not handling the reserved byte accounting properly for data
references. Metadata was fine, if it errored out the error paths would
free the bytes_reserved count and pin the extent, but it even missed one
of the error cases. So instead move this handling up into
run_one_delayed_ref so we are sure that both cases are properly cleaned
up in case of a transaction abort.
CC: stable@vger.kernel.org # 4.18+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If we use up our block group before allocating a new one we'll easily
get a max_extent_size that's set really really low, which will result in
a lot of fragmentation. We need to make sure we're resetting the
max_extent_size when we add a new chunk or add new space.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When writing out a block group free space cache we can end deadlocking
with ourselves on an extent buffer lock resulting in a warning like the
following:
This is because at write_one_cache_group() when we are COWing a leaf from
the extent tree we end up allocating a new block group (chunk) and,
because we have hit a threshold on the number of bytes reserved for system
chunks, we attempt to finalize the creation of new block groups from the
current transaction, by calling btrfs_create_pending_block_groups().
However here we also need to modify the extent tree in order to insert
a block group item, and if the location for this new block group item
happens to be in the same leaf that we were COWing earlier, we deadlock
since btrfs_search_slot() tries to write lock the extent buffer that we
locked before at write_one_cache_group().
We have already hit similar cases in the past and commit d9a0540a79f8
("Btrfs: fix deadlock when finalizing block group creation") fixed some
of those cases by delaying the creation of pending block groups at the
known specific spots that could lead to a deadlock. This change reworks
that commit to be more generic so that we don't have to add similar logic
to every possible path that can lead to a deadlock. This is done by
making __btrfs_cow_block() disallowing the creation of new block groups
(setting the transaction's can_flush_pending_bgs to false) before it
attempts to allocate a new extent buffer for either the extent, chunk or
device trees, since those are the trees that pending block creation
modifies. Once the new extent buffer is allocated, it allows creation of
pending block groups to happen again.
This change depends on a recent patch from Josef which is not yet in
Linus' tree, named "btrfs: make sure we create all new block groups" in
order to avoid occasional warnings at btrfs_trans_release_chunk_metadata().
Fixes: d9a0540a79f8 ("Btrfs: fix deadlock when finalizing block group creation") CC: stable@vger.kernel.org # 4.4+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199753 Link: https://lore.kernel.org/linux-btrfs/CAJtFHUTHna09ST-_EEiyWmDH6gAqS6wa=zMNMBsifj8ABu99cw@mail.gmail.com/ Reported-by: E V <eliventer@gmail.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We want to release the unused reservation we have since it refills the
delayed refs reserve, which will make everything go smoother when
running the delayed refs if we're short on our reservation.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Liu Bo <bo.liu@linux.alibaba.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
During buffered writes, we follow this basic series of steps:
again:
lock all the pages
wait for writeback on all the pages
Take the extent range lock
wait for ordered extents on the whole range
clean all the pages
if (copy_from_user_in_atomic() hits a fault) {
drop our locks
goto again;
}
dirty all the pages
release all the locks
The extra waiting, cleaning and locking are there to make sure we don't
modify pages in flight to the drive, after they've been crc'd.
If some of the pages in the range were already dirty when the write
began, and we need to goto again, we create a window where a dirty page
has been cleaned and unlocked. It may be reclaimed before we're able to
lock it again, which means we'll read the old contents off the drive and
lose any modifications that had been pending writeback.
We don't actually need to clean the pages. All of the other locking in
place makes sure we don't start IO on the pages, so we can just leave
them dirty for the duration of the write.
Fixes: 73d59314e6ed (the original btrfs merge) CC: stable@vger.kernel.org # v4.4+ Signed-off-by: Chris Mason <clm@fb.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 499f377f49f08 (btrfs: iterate over unused chunk space in FITRIM)
fixed free space trimming, but introduced latency when it was running.
This is due to it pinning the transaction using both a incremented
refcount and holding the commit root sem for the duration of a single
trim operation.
This was to ensure safety but it's unnecessary. We already hold the the
chunk mutex so we know that the chunk we're using can't be allocated
while we're trimming it.
In order to check against chunks allocated already in this transaction,
we need to check the pending chunks list. To to that safely without
joining the transaction (or attaching than then having to commit it) we
need to ensure that the dev root's commit root doesn't change underneath
us and the pending chunk lists stays around until we're done with it.
We can ensure the former by holding the commit root sem and the latter
by pinning the transaction. We do this now, but the critical section
covers the trim operation itself and we don't need to do that.
This patch moves the pinning and unpinning logic into helpers and unpins
the transaction after performing the search and check for pending
chunks.
Limiting the critical section of the transaction pinning improves the
latency substantially on slower storage (e.g. image files over NFS).
Fixes: 499f377f49f08 ("btrfs: iterate over unused chunk space in FITRIM") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When we fail to start a transaction in btrfs_dev_replace_start, we leave
dev_replace->replace_start set to STARTED but clear ->srcdev and
->tgtdev. Later, that can result in an Oops in
btrfs_dev_replace_progress when having state set to STARTED or SUSPENDED
implies that ->srcdev is valid.
Also fix error handling when the state is already STARTED or SUSPENDED
while starting. That, too, will clear ->srcdev and ->tgtdev even though
it doesn't own them. This should be an impossible case to hit since we
should be protected by the BTRFS_FS_EXCL_OP bit being set. Let's add an
ASSERT there while we're at it.
Fixes: e93c89c1aaaaa (Btrfs: add new sources for device replace code) CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Use the new of_get_compatible_child() helper to lookup the sibling
instead of using of_find_compatible_node(), which searches the entire
tree from a given start node and thus can return an unrelated (i.e.
non-sibling) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the parent device node).
While at it, also fix the related cec-node reference leak.
Fixes: 8f83f26891e1 ("drm/mediatek: Add HDMI support") Cc: stable <stable@vger.kernel.org> # 4.8 Cc: Junzhi Zhao <junzhi.zhao@mediatek.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: CK Hu <ck.hu@mediatek.com> Cc: David Airlie <airlied@linux.ie> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The cec_phys_addr_validate() function will be moved to V4L2,
so use a simplified variant of that function in cec-api.c.
cec now no longer calls cec_phys_addr_validate() and it can
be safely moved to V4L2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: <stable@vger.kernel.org> # for v4.17 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This function is needed by both V4L2 and CEC, so move this to
cec.h as a static inline since there are no obvious shared
modules between the two subsystems.
This patch, together with the following ones, fixes a
dependency bug: if CEC_CORE is disabled, then building adv7604
(and other HDMI receivers) will fail because an essential
function is now stubbed out.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: <stable@vger.kernel.org> # for v4.17 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Use the new of_get_compatible_child() helper to lookup the mdio child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
Fixes: aa09677cba42 ("net: bcmgenet: add MDIO routines") Cc: stable <stable@vger.kernel.org> # 3.15 Cc: David S. Miller <davem@davemloft.net> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The AFU Information DVSEC capability is a means to extract common,
general information about all of the AFUs associated with a Function
independent of the specific functionality that each AFU provides.
Write in the AFU Index field allows to access to the descriptor data
for each AFU.
With the current code, we are not able to access to these specific data
when the index >= 1 because we are writing to the wrong location.
All requests to the data of each AFU are pointing to those of the AFU 0,
which could have impacts when using a card with more than one AFU per
function.
This patch fixes the access to the AFU Descriptor Data indexed by the
AFU Info Index field.
Use the new of_get_compatible_child() helper to lookup the usb sibling
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(non-sibling) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the parent device node).
While at it, also fix the related phy-node reference leak.
Fixes: f5e4edb8c888 ("power: twl4030_charger: find associated phy by more reliable means.") Cc: stable <stable@vger.kernel.org> # 4.2 Cc: NeilBrown <neilb@suse.de> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Sebastian Reichel <sre@kernel.org> Reviewed-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix a commit 8a8158c85e1e ("MIPS: memset.S: EVA & fault support for
small_memset") regression and remove assembly warnings:
arch/mips/lib/memset.S: Assembler messages:
arch/mips/lib/memset.S:243: Warning: Macro instruction expanded into multiple instructions in a branch delay slot
triggering with the CPU_DADDI_WORKAROUNDS option set and this code:
PTR_SUBU a2, t1, a0
jr ra
PTR_ADDIU a2, 1
This is because with that option in place the DADDIU instruction, which
the PTR_ADDIU CPP macro expands to, becomes a GAS macro, which in turn
expands to an LI/DADDU (or actually ADDIU/DADDU) sequence:
Correct this by switching off the `noreorder' assembly mode and letting
GAS schedule this jump's delay slot, as there is nothing special about
it that would require manual scheduling. With this change in place
correct code is produced:
PPC_INVALIDATE_ERAT is slbia IH=7 which is a new variant introduced
with POWER9, and the result is undefined on earlier CPUs.
Commits 7b9f71f974 ("powerpc/64s: POWER9 machine check handler") and d4748276ae ("powerpc/64s: Improve local TLB flush for boot and MCE on
POWER9") caused POWER7/8 code to use this instruction. Remove it. An
ERAT flush can be made by invalidatig the SLB, but before POWER9 that
requires a flush and rebolt.
Fixes: 7b9f71f974 ("powerpc/64s: POWER9 machine check handler") Fixes: d4748276ae ("powerpc/64s: Improve local TLB flush for boot and MCE on POWER9") Cc: stable@vger.kernel.org # v4.11+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently on P9N DD2.1 we end up taking infinite TM facility
unavailable exceptions on the first TM usage by userspace.
In the special case of TM no suspend (P9N DD2.1), Linux is told TM is
off via CPU dt-ftrs but told to (partially) use it via
OPAL_REINIT_CPUS_TM_SUSPEND_DISABLED. So HFSCR[TM] will be off from
dt-ftrs but we need to turn it on for the no suspend case.
This patch fixes this by enabling HFSCR TM in this case.
Cc: stable@vger.kernel.org # 4.15+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Use the new of_get_compatible_child() helper to lookup the nfc child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the parent node).
Fixes: e097dc624f78 ("NFC: nfcmrvl: add UART driver") Fixes: d8e018c0b321 ("NFC: nfcmrvl: update device tree bindings for Marvell NFC") Cc: stable <stable@vger.kernel.org> # 4.2 Cc: Vincent Cuissard <cuissard@marvell.com> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
PageTransCompoundMap() returns true for hugetlbfs and THP
hugepages. This behaviour incorrectly leads to stage 2 faults for
unsupported hugepage sizes (e.g., 64K hugepage with 4K pages) to be
treated as THP faults.
Tighten the check to filter out hugetlbfs pages. This also leads to
consistently mapping all unsupported hugepage sizes as PTE level
entries at stage 2.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com> Reviewed-by: Suzuki Poulose <suzuki.poulose@arm.com> Cc: Christoffer Dall <christoffer.dall@arm.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: stable@vger.kernel.org # v4.13+ Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
commit 901ef845fa2469c ("selinux: allow per-file labeling for cgroupfs")
broke mounting of cgroup2 under older SELinux policies which lacked
a genfscon rule for cgroup2. This prevents mounting of cgroup2 even
when SELinux is permissive.
Change the handling when there is no genfscon rule in policy to
just mark the inode unlabeled and not return an error to the caller.
This permits mounting and access if allowed by policy, e.g. to
unconfined domains.
I also considered changing the behavior of security_genfs_sid() to
never return -ENOENT, but the current behavior is relied upon by
other callers to perform caller-specific handling.
Fixes: 901ef845fa2469c ("selinux: allow per-file labeling for cgroupfs") CC: <stable@vger.kernel.org> Reported-by: Dmitry Vyukov <dvyukov@google.com> Reported-by: Waiman Long <longman@redhat.com> Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Tested-by: Waiman Long <longman@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The code EXT4_IOC_SWAP_BOOT ioctl hasn't been updated in a while, and
it's a bit broken with respect to more modern ext4 kernels, especially
metadata checksums.
Other problems fixed with this commit:
* Don't allow installing a DAX, swap file, or an encrypted file as a
boot loader.
* Respect the immutable and append-only flags.
* Wait until any DIO operations are finished *before* calling
truncate_inode_pages().
* Don't swap inode->i_flags, since these flags have nothing to do with
the inode blocks --- and it will give the IMA/audit code heartburn
when the inode is evicted.
This enum has become part of the uABI, as both RXE and the
ib_uverbs_post_send() command expect userspace to supply values from this
enum. So it should be properly placed in include/uapi/rdma.
In userspace this enum is called 'enum ibv_wr_opcode' as part of
libibverbs.h. That enum defines different values for IB_WR_LOCAL_INV,
IB_WR_SEND_WITH_INV, and IB_WR_LSO. These were introduced (incorrectly, it
turns out) into libiberbs in 2015.
The kernel has changed its mind on the numbering for several of the IB_WC
values over the years, but has remained stable on IB_WR_LOCAL_INV and
below.
Based on this we can conclude that there is no real user space user of the
values beyond IB_WR_ATOMIC_FETCH_AND_ADD, as they have never worked via
rdma-core. This is confirmed by inspection, only rxe uses the kernel enum
and implements the latter operations. rxe has clearly never worked with
these attributes from userspace. Other drivers that support these opcodes
implement the functionality without calling out to the kernel.
To make IB_WR_SEND_WITH_INV and related work for RXE in userspace we
choose to renumber the IB_WR enum in the kernel to match the uABI that
userspace has bee using since before Soft RoCE was merged. This is an
overall simpler configuration for the whole software stack, and obviously
can't break anything existing.
The OPP table was freed, but not the individual OPPs which is done from
_dev_pm_opp_remove_table(). Fix it by calling _dev_pm_opp_remove_table()
as well.
Cc: 4.18 <stable@vger.kernel.org> # v4.18 Fixes: 3ba98324e81a ("PM / OPP: Get performance state using genpd helper") Tested-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The reason is in step 9) we missed to recover cold bit flag in inode
block, so later, in fsync, we will skip write inode block due to below
condition check, result in lossing data in another SPOR.
f2fs_fsync_node_pages()
if (!IS_DNODE(page) || !is_cold_node(page))
continue;
Note that, I guess that some non-dir inode has already lost cold bit
during POR, so in order to reenable recovery for those inode, let's
try to recover cold bit in f2fs_iget() to save more fsynced data.
On a fresh connection, an RPC/RDMA client is supposed to send only
one RPC Call until it gets a credit grant in the first RPC Reply
from the server [RFC 8166, Section 3.3.3].
There is a bug in the Linux client's credit accounting mechanism
introduced by commit e7ce710a8802 ("xprtrdma: Avoid deadlock when
credit window is reset"). On connect, it simply dumps all pending
RPC Calls onto the new connection.
Servers have been tolerant of this bad behavior. Currently no server
implementation ever changes its credit grant over reconnects, and
servers always repost enough Receives before connections are fully
established.
To correct this issue, ensure that the client resets both the credit
grant _and_ the congestion window when handling a reconnect.
Fixes: e7ce710a8802 ("xprtrdma: Avoid deadlock when credit ... ") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: stable@kernel.org Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Use the new of_get_compatible_child() helper to lookup the mdio-internal
child node instead of using of_find_compatible_node(), which searches
the entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the mdio-mux node). Fortunately, this was inadvertently
balanced by a failure to drop the mdio-mux reference after lookup.
While at it, also fix the related mdio-internal- and phy-node reference
leaks.
Fixes: 634db83b8265 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs") Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Sometimes we have empty banks within the GPIO block. This commit allows
proper handling of 0 width GPIO banks. We handle 0 width GPIO banks by
incrementing the bank and number of GPIOs, but not initializing them.
This will mean a call into the non-existent GPIOs will return an error.
Also remove "GPIO registered" dev print. This information is misleading
since the incremented banks and gpio_base do not reflect the actual GPIOs
that get initialized. We leave this information out since it is already
printed with dev_dbg.
projects / mirror_ubuntu-bionic-kernel.git / log