drm/bridge: adv7511: Properly update EDID when no EDID was found
Currently adv7511_get_modes() bails out early when no EDID could be
retrieved. This leaves the previous EDID in place, which is typically not
the intended behavior and might confuse applications. Instead the EDID
should be cleared when no EDID could be retrieved.
All functions that are called after the EDID check handle the case where
the EDID is NULL just fine and exhibit the expected behavior, so just drop
the check.
drm/atomic: Prepare drm_modeset_lock infrastructure for interruptible waiting, v2.
When we want to make drm_atomic_commit interruptible, there are a lot of
places that call the lock function, which we don't have control over.
Rather than trying to convert every single one, it's easier to toggle
interruptible waiting per acquire_ctx. If drm_modeset_acquire_init is
called with DRM_MODESET_ACQUIRE_INTERRUPTIBLE, then we will perform
interruptible waits in drm_modeset_lock and drm_modeset_backoff.
Changes since v1:
- Fix locking example in drm_modeset_lock.c to be compatible
with interruptible waiting (xexaxo) and make it default.
Uninterruptible waiting shouldn't happen except in corner cases,
but the example will still apply if the flag is removed.
- Add drm_modeset_lock_single_interruptible() to documentation.
- Fix dead link to removed drm_modeset_lock_interruptible() in
drm_modeset_lock().
This makes use of the drm_simple_display_pipe_attach_bridge()
call and removes the two calls removing the bridge, which were
erroneous: they unregister the bridge which is not what
we want, we just want to unreference it and that is already
handled by the core.
drm/dp/mst: Sideband message transaction to power up/down nodes
The POWER_DOWN_PHY and POWER_UP_PHY sideband message transactions allow
the source to reqest any node in a mst path or a whole path to be
powered down or up. This allows drivers to target a specific sink in the
MST topology, an improvement over just power managing the imediate
downstream device. Secondly, since the request-reply protocol waits for an
ACK, we can be sure that a downstream sink has enough time to respond to a
power up/down request.
v2: Fix memory leak (Lyude) Cc: Lyude <lyude@redhat.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170907001458.9399-1-dhinakaran.pandiyan@intel.com Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Ville Syrjälä [Fri, 1 Sep 2017 16:53:28 +0000 (19:53 +0300)]
drm: Make __drm_object_property_get_value() static
Make __drm_object_property_get_value() static to fix the following
sparse warning:
drm_mode_object.c:250:5: warning: symbol '__drm_object_property_get_value' was not declared. Should it be static?
Ville Syrjälä [Fri, 1 Sep 2017 16:53:25 +0000 (19:53 +0300)]
drm: Make syncobj import/export functions static
Fix the following sparse warnings by making functions static:
drm_syncobj.c:420:5: warning: symbol 'drm_syncobj_import_sync_file_fence' was not declared. Should it be static?
drm_syncobj.c:441:5: warning: symbol 'drm_syncobj_export_sync_file' was not declared. Should it be static?
The ARM reference designs in the Versatile family: Integrator,
Versatile and RealView can make use of the new DRM driver as well.
We just need to create a bit of platform-specific code for them
that we isolate to its own file.
The old codebase has a delay between enabling and powering up the
PL11x.
According to the manual for PL110, ARM DDI 0161E page 1-5 and
the PL111 manual ARM DDI 0293C page 1-6, the power sequence should
be such that once Vdd is stable (which we assume it is at boot)
LCDEN is enabled first and then CLPOWER should be enabled
"after the signals have stabilized" and this is said to
be display-dependent. The old codebase uses 20ms.
We detect and enable the use of the PL110 variant, an earlier
incarnation of PL111. The only real difference is that the
control and interrupt enable registers have swapped place.
The Versatile AB and Versatile PB have a variant inbetween
PL110 and PL111, it is PL110 but they have already swapped the
two registers so those two need a bit of special handling.
drm/pl111: Replace custom connector with panel bridge
This replaces the custom connector in the PL111 with the
panel bridge helper.
This works nicely for all standard panels, but since there
are several PL11x-based systems that will need to use the dumb
VGA connector bridge we use drm_of_find_panel_or_bridge()
and make some headroom for dealing with bridges that are
not panels as well, and drop a TODO in the code.
drm/sun4i: call drm_vblank_init with correct number of crtcs
If we want to have vblank on both pipelines at the same time, we need
to call drm_vblank_init with num_crtcs = 2.
Instead, since the crtc init calls correctly set mode_config.num_crtc,
we can move the drm_vblank_init call to after the crtc init code is
called, which is the component bind part. Then we can just pass
mode_config.num_crtc in.
The TCON has a mux to select the source of the data to display.
This mux includes selecting the display backends. On the A31,
which has two display pipelines, this mux can let the TCON
select either backend as its data source. Although the muxing
can be changed on the fly, DRM needs to be able to group a
bunch of layers such that they get switched to another crtc
together. This is because the display backend does the layer
compositing, while the TCON generates the display timings.
This constraint is not supported by DRM.
Here we simply pair up backends and TCONs with the same ID.
drm/sun4i: tcon: get TCON ID and matching engine with remote endpoint ID
The device tree binding for sun4i-drm says:
For all connections between components up to the TCONs in the display
pipeline, when there are multiple components of the same type at the
same depth, the local endpoint ID must be the same as the remote
component's index. For example, if the remote endpoint is Frontend 1,
then the local endpoint ID must be 1.
We should be able to get the TCON's ID directly from any of the remote
endpoints from its input port. With the ID, we can then go through the
list of registered engines and find a matching one by ID.
However the A31 device tree is incorrect. We assumed that there were no
cross pipeline connections between the backends and TCONs. As a result,
in all the endpoints between the backends and TCONs of the second
display pipeline, the endpoint IDs were incorrectly set to 0, when in
fact they should've been set to 1.
To maintain compatibility with this incorrect device tree, we first
check if the TCON's input port has 1 or many endpoints. If there are
more than 1, then it is likely a fixed version, and we can proceed
with the new method. If there is only 1 endpoint, then it is possibly
an incorrect version, or it could be the SoC only has one pipeline.
In either case we fall back to using the old method of traversing
the input connections to find a matching engine, and then get its
ID.
drm/sun4i: tcon: Check for multiple paths between TCONs and backends
The patch b317fa3ba11a ("drm/sun4i: tcon: Find matching display backend
by device node matching") assumed a one-to-one mapping between TCONs
and backends. This turned out wrong, as we found muxing controls in the
TCON of the A31, and undocumented usage of the backend output selector
of the A20.
Make sun4i_tcon_find_engine() bail out if the current node has multiple
input connections.
drm/sun4i: add components in breadth first traversal order
The encoder drivers use drm_of_find_possible_crtcs to get upstream
crtcs from the device tree using of_graph. For the results to be
correct, encoders must be probed/bound after _all_ crtcs have been
created. The existing code uses a depth first recursive traversal
of the of_graph, which means the encoders downstream of the TCON
get add right after the first TCON. The second TCON or CRTC will
never be properly associated with encoders connected to it.
Other platforms, such as Rockchip, deal with this by probing all
CRTCs first, then all subsequent components. This is easy to do
since the CRTCs correspond to just one device node, and are the
first nodes in the pipeline.
However with Allwinner SoCs, the function of the CRTC is split
between the display backend (DE 1.0) or mixer (DE 2.0), which does
scan-out and compositing, and the TCON, which generates the display
timing signals. Further complicating the process, there may be a
Dynamic Range Controller between the backend and the TCON. Also, the
backend is preceded by the frontend, with a Display Enhancement Unit
possibly in between.
In a dual display pipeline setup, both frontends can feed either
backend, and both backends can feed either TCON. We want all
components of the same type to be added before the next type in the
pipeline. Fortunately, the pipelines are perfectly symmetric, i.e.
components of the same type are at the same depth when counted from
the frontend. The only exception is the third pipeline in the A80
SoC, which we do not support anyway.
Hence we can use a breadth first search traversal order to add
components. We do not need to check for duplicates. The component
matching system handles this for us.
When binding the TCON, we were checking the reset control status and
asserting reset if it wasn't in reset. The check failed to account for
the reset control API returning error codes if the status callback was
not implemented.
Since we want the TCON to be reset in all cases, use reset_control_reset
to force a reset instead.
dma-buf/sw_sync: force signal all unsignaled fences on dying timeline
To avoid hanging userspace components that might have been waiting on the
active fences of the destroyed timeline we need to signal with error all
remaining fences on such timeline.
This restore the default behaviour of the Android sw_sync framework, which
Android still relies on. It was broken on the dma fence conversion a few
years ago and never fixed.
v2: Do not bother with cleanup do the list (Chris Wilson)
Colin Ian King [Fri, 8 Sep 2017 14:05:04 +0000 (15:05 +0100)]
drm/vc4: clean up error handling on devm_kzalloc failure
The current error handling when devm_kzalloc fails performs a
non-null check on connector which is redundant because connector
is null at that failure point. Once this is removed, make the
failure path into a trivial -ENOMEM return to clean up the
error handling. Also remove need to initialize connector to NULL.
drm/atomic: Make async plane update checks work as intended, v2.
By always keeping track of the last commit in plane_state, we know
whether there is an active update on the plane or not. With that
information we can reject the fast update, and force the slowpath
to be used as was originally intended.
We cannot use plane_state->crtc->state here, because this only mentions
the most recent commit for the crtc, but not the planes that were part
of it. We specifically care about what the last commit involving this
plane is, which can only be tracked with a pointer in the plane state.
Changes since v1:
- Clean up the whole function here, instead of partially earlier.
- Add mention in the commit message why we need commit in plane_state.
- Swap plane->state in intel_legacy_cursor_update, instead of
reassigning all variables. With this commit We know that the cursor
is not part of any active commits so this hack can be removed.
Cc: Gustavo Padovan <gustavo.padovan@collabora.com> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20170904104838.23822-7-maarten.lankhorst@linux.intel.com
[mlankhorst: Amend commit for merge conflicts with drm-intel]
drm/atomic: Fix freeing connector/plane state too early by tracking commits, v3.
Currently we neatly track the crtc state, but forget to look at
plane/connector state.
When doing a nonblocking modeset, immediately followed by a setprop
before the modeset completes, the setprop will see the modesets new
state as the old state and free it.
This has to be solved by waiting for hw_done on the connector, even
if it's not assigned to a crtc. When a connector is unbound we take
the last crtc commit, and when it stays unbound we create a new
fake crtc commit for that gets signaled on hw_done for all the
planes/connectors.
We wait for it the same way as we do for crtc's, which will make
sure we never run into a use-after-free situation.
Changes since v1:
- Only create a single disable commit. (danvet)
- Fix leak in intel_legacy_cursor_update.
Changes since v2:
- Make reference counting in drm_atomic_helper_setup_commit
more obvious. (pinchartl)
- Call cleanup_done for fake commit. (danvet)
- Add comments to drm_atomic_helper_setup_commit. (danvet, pinchartl)
- Add comment to drm_atomic_helper_swap_state. (pinchartl)
drm/atomic: Remove waits in drm_atomic_helper_commit_cleanup_done, v2.
When commit synchronization through drm_crtc_commit was first
introduced, we tried to solve the problem of the flip_done
needing a reference count by blocking in cleanup_done.
This has been changed by commit 24835e442f28 ("drm: reference count
event->completion") which made the waits here no longer needed.
However, even after this commit we still needed the wait because
otherwise we cannot wait for the flip_done because this item might
have been removed from the list.
Changed since v1:
- Make mention of cleanup_done completing before flip_done.
drm/atomic: Move drm_crtc_commit to drm_crtc_state, v4.
Most code only cares about the current commit or previous commit.
Fortuantely we already have a place to track those. Move it to
drm_crtc_state where it belongs. :)
The per-crtc commit_list is kept for places where we have to look
deeper than the current or previous commit for checking whether to stall
on unpin. This is used in drm_atomic_helper_setup_commit and
intel_has_pending_fb_unpin.
Changes since v1:
- Update kerneldoc for drm_crtc.commit_list. (danvet)
Changes since v2:
- Remove drm_atomic_helper_async_check hunk. (pinchartl)
Changes since v3:
- Fix use-after-free in drm_atomic_helper_commit_cleanup_done().
The next commit removes the wait for flip_done in in
drm_atomic_helper_commit_cleanup_done, but we need it for the tests
to pass. Instead of using complicated vblank tracking which ends
up being ignored anyway, call the correct atomic helper. :)
Changes since v1:
- Always call drm_atomic_helper_wait_for_flip_done,
even for legacy cursor updates. (danvet)
drm/stm: fix warning about multiplication in condition
gcc-7 complains about multiplying within a condition being
suspicious:
drivers/gpu/drm/stm/dw_mipi_dsi-stm.c: In function 'dsi_pll_get_clkout_khz':
drivers/gpu/drm/stm/dw_mipi_dsi-stm.c:117:10: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
The code here is correct, but can be easily rephrased to make
that more obvious. I also swap out the error handling and the normal
code path for clarity.
Fixes: b0f09a3c69d9 ("drm/stm: Add STM32 DSI controller driver") Acked-by: Philippe Cornu <philippe.cornu@st.com> Tested-by: Philippe Cornu <philippe.cornu@st.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20170906131331.2691300-1-arnd@arndb.de
gcc-8 points out a condition that almost certainly doesn't
do what the author had in mind:
drivers/gpu/drm/gma500/mdfld_intel_display.c: In function 'mdfldWaitForPipeEnable':
drivers/gpu/drm/gma500/mdfld_intel_display.c:102:37: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
This changes it to a simple bit mask operation to check
whether the bit is set.
The header comment in include/trace/define_trace.h specifies that the
TRACE_INCLUDE_PATH needs to be relative to the define_trace.h header
rather than the trace file including it. Most instances get that wrong
and work around it by adding the $(src) directory to the include path.
While this works, it is preferable to refer to the correct path to the
trace file in the first place and avoid any workaround.
The header comment in include/trace/define_trace.h specifies that the
TRACE_INCLUDE_PATH needs to be relative to the define_trace.h header
rather than the trace file including it. Most instances get that wrong
and work around it by adding the $(src) directory to the include path.
While this works, it is preferable to refer to the correct path to the
trace file in the first place and avoid any workaround.
The header comment in include/trace/define_trace.h specifies that the
TRACE_INCLUDE_PATH needs to be relative to the define_trace.h header
rather than the trace file including it. Most instances get that wrong
and work around it by adding the $(src) directory to the include path.
While this works, it is preferable to refer to the correct path to the
trace file in the first place and avoid any workaround.
Philippe CORNU [Tue, 1 Aug 2017 13:23:08 +0000 (15:23 +0200)]
drm/bridge/synopsys: dsi: explicitly request exclusive reset control
Based on patch "Convert drivers to explicit reset API" from Philipp Zabel
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
Philippe CORNU [Tue, 1 Aug 2017 13:23:07 +0000 (15:23 +0200)]
drm/bridge/synopsys: dsi: Register list clean up
This patch cleans up the Synopsys mipi dsi register list:
- rename registers according to the Synopsys documentation
(1.30 & 1.31)
- fix typos
- re-order registers for a better coherency
drm/tve200: Replace custom connector with panel bridge
This replaces the custom connector in the TVE200 with the
panel bridge helper. As long as we're just using panels
and no other bridges, this works just fine.
Noralf Trønnes [Mon, 28 Aug 2017 17:17:43 +0000 (19:17 +0200)]
drm/fb-helper: Avoid NULL ptr dereference in fb_set_suspend()
drm_fb_helper_resume_worker() uses fb_helper->fbdev to call
fb_set_suspend() which dereferences the pointer.
Move sync-canceling of the resume worker in drm_fb_helper_fini() before
setting fb_helper->fbdev to NULL. Move dirty_work as well.
The error messages generated by the SCDC helpers are somewhat
inconsistent with other DRM errors and even with other errors in the
same file. Fix them all up to use a common format.
Rodrigo Vivi [Fri, 25 Aug 2017 20:16:12 +0000 (13:16 -0700)]
drm/tve200: Pass NULL format_modifier to drm_simple_display_pipe_init
This Fixes build on branches where we already have format-modifier.
Reference: https://lists.freedesktop.org/archives/dri-devel/2017-August/151044.html Fixes: 179c02fe90a4 ("drm/tve200: Add new driver for TVE200") Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Janet Morgan <janet.morgan@intel.com> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Daniel Stone <daniels@collabora.com> (v2) Cc: Liviu Dudau <Liviu.Dudau@arm.com> Cc: Daniel Stone <daniels@collabora.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Daniel Stone <daniels@collabora.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20170825201612.23056-1-rodrigo.vivi@intel.com
Linus Walleij [Sun, 20 Aug 2017 10:05:55 +0000 (12:05 +0200)]
drm/tve200: Add new driver for TVE200
This adds a new DRM driver for the Faraday Technology TVE200
block. This "TV Encoder" encodes a ITU-T BT.656 stream and can
be found in the StorLink SL3516 (later Cortina Systems CS3516)
as well as the Grain Media GM8180.
I do not have definitive word from anyone at Faraday that this
IP block is theirs, but it bears the hallmark of their 3-digit
version code (200) and is used in two SoCs from completely
different companies. (Grain Media was fully owned by Faraday
until it was transferred to NovoTek this january, and
Faraday did lots of work on the StorLink SoCs.)
The D-Link DIR-685 uses this in connection with the Ilitek
ILI9322 panel driver that supports BT.656 input, while the
GM8180 apparently has been used with the Cirrus Logic CS4954
digital video encoder. The oldest user seems to be
something called Techwall 2835.
This driver is heavily inspired by Eric Anholt's PL111
driver and therefore I have mentioned all the ancestor authors
in the header file.
Linus Walleij [Sun, 20 Aug 2017 10:05:54 +0000 (12:05 +0200)]
drm/tve200: Add DT bindings
This adds device tree bindings for the Faraday TVE200 IP block.
This IP block is present in the Gemini ARM SoC and also in some
Grain Media GMxxxx SoCs.
Daniel Vetter [Fri, 18 Aug 2017 17:43:28 +0000 (19:43 +0200)]
drm/doc: Document ioctl errno value patterns
We're not super-consistent about these, but I think it's worth to
document at least the commmon patterns.
v2:
- Add a not about ENOTTY (it's just a confusing name, but used
exactly what it's meant for in DRM) (Chris).
- Unconfuse the text for ENODEV (Daniel)
- Move text undert the IOCTL heading (Chris).
- typos
Cc: Daniel Stone <daniel@fooishbar.org> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: "Zhang, Tina" <tina.zhang@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170818174328.6386-1-daniel.vetter@ffwll.ch
Ville Syrjälä [Fri, 18 Aug 2017 13:49:51 +0000 (16:49 +0300)]
drm/dp: Add defines for DP SDP types
Add defines for the secondary data packet (SDP) types from the spec.
These are the DP specific ones, and in addition HDMI infoframe types
(see enum hdmi_infoframe_type) are also valid SDP types.
v2: Add more SDP types
v3: Note the DP version that added each SDP type (Rodrigo)
Chris Wilson [Sat, 19 Aug 2017 12:05:58 +0000 (13:05 +0100)]
drm: Release driver tracking before making the object available again
This is the same bug as we fixed in commit f6cd7daecff5 ("drm: Release
driver references to handle before making it available again"), but now
the exposure is via the PRIME lookup tables. If we remove the
object/handle from the PRIME lut, then a new request for the same
object/fd will generate a new handle, thus for a short window that
object is known to userspace by two different handles. Fix this by
releasing the driver tracking before PRIME.
Fixes: 0ff926c7d4f0 ("drm/prime: add exported buffers to current fprivs
imported buffer list (v2)") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Rob Clark <robdclark@gmail.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Thierry Reding <treding@nvidia.com> Cc: stable@vger.kernel.org Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20170819120558.6465-1-chris@chris-wilson.co.uk
Arvind Yadav [Sat, 19 Aug 2017 18:28:20 +0000 (23:58 +0530)]
drm: i2c: tda998x: constify i2c_device_id
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Arvind Yadav [Sat, 19 Aug 2017 18:28:19 +0000 (23:58 +0530)]
drm: i2c: sil164: constify i2c_device_id
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Arvind Yadav [Sat, 19 Aug 2017 18:28:18 +0000 (23:58 +0530)]
drm: i2c: ch7006: constify i2c_device_id
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Marco Franchi [Thu, 20 Jul 2017 16:12:59 +0000 (13:12 -0300)]
drm/panel: Add driver for Seiko 43WVF1G panel
Add driver for Seiko Instruments Inc. 4.3" WVGA (800 x RGB x 480)
TFT with Touch-Panel.
Datasheet available at:
http://www.glyn.de/data/glyn/media/doc/43wvf1g-0.pdf
Seiko 43WVF1G panel has two power supplies: avdd and dvdd and they
require a specific power on/down sequence.
For this reason the simple panel driver cannot be used to drive this
panel, so create a new one heavily based on simple panel.
Based on initial patch submission from Breno Lima.
Thierry Reding [Mon, 14 Aug 2017 14:00:11 +0000 (16:00 +0200)]
MAINTAINERS: drm/panel is now maintained in drm-misc
drm/panel is a good candidate for the drm-misc group maintainership and
it's been maintained in the common drm-misc tree for a release, so make
it official.
During panel removal or system shutdown panel_simple_disable() is called
which disables the panel backlight but the panel is still powered due to
missing calls to panel_simple_unprepare().
Philippe CORNU [Mon, 17 Jul 2017 13:19:53 +0000 (15:19 +0200)]
drm/panel: Add support for OTM8009A panel driver
This patch adds Orise Tech OTM8009A 3.97" 480x800 TFT LCD
panel driver (MIPI-DSI video mode). The panel backlight is
managed through the DSI link. This panel driver is used in
several STM32 boards.
This patch adds MIPI-DSI based S6E63J0X03 AMOLED LCD panel driver
which uses MIPI DSI bus to communicate with panel. The panel has
320×320 resolution in 1.63" physical panel. This panel is used in
Samsung Galaxy Gear 2.
Arvind Yadav [Sat, 12 Aug 2017 08:35:19 +0000 (14:05 +0530)]
drm: udl: constify usb_device_id
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Dave Airlie [Thu, 17 Aug 2017 19:41:32 +0000 (05:41 +1000)]
Merge tag 'omapdrm-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next
omapdrm changes for v4.14
* HDMI hot plug IRQ support (instead of polling)
* Big driver cleanup from Laurent (no functional changes)
* OMAP5 DSI support (only the pinmuxing was missing)
* tag 'omapdrm-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (60 commits)
drm/omap: Potential NULL deref in omap_crtc_duplicate_state()
drm/omap: remove no-op cleanup code
drm/omap: rename omapdrm device back
drm: omapdrm: Remove omapdrm platform data
ARM: OMAP2+: Don't register omapdss device for omapdrm
ARM: OMAP2+: Remove unused omapdrm platform device
drm: omapdrm: Remove the omapdss driver
drm: omapdrm: Register omapdrm platform device in omapdss driver
drm: omapdrm: hdmi: Don't allocate PHY features dynamically
drm: omapdrm: hdmi: Configure the PHY from the HDMI core version
drm: omapdrm: hdmi: Configure the PLL from the HDMI core version
drm: omapdrm: hdmi: Pass HDMI core version as integer to HDMI audio
drm: omapdrm: hdmi: Replace OMAP SoC model check with HDMI xmit version
drm: omapdrm: hdmi: Rename functions and structures to use hdmi_ prefix
drm/omap: add OMAP5 DSIPHY lane-enable support
drm/omap: use regmap_update_bit() when muxing DSI pads
drm: omapdrm: Remove dss_features.h
drm: omapdrm: Move supported outputs feature to dss driver
drm: omapdrm: Move DSS_FCK feature to dss driver
drm: omapdrm: Move PCD, LINEWIDTH and DOWNSCALE features to dispc driver
...
Dave Airlie [Thu, 17 Aug 2017 19:30:53 +0000 (05:30 +1000)]
Merge branch 'drm-next-4.14' of git://people.freedesktop.org/~agd5f/linux into drm-next
More features for 4.14. Nothing too major here. I have a few more additional
patches for large page support in vega10 among other things, but they require
some resevation object patches from drm-misc-next, so I'll send that request
once you've pulled the latest drm-misc-next. Highlights:
- Fixes for ACP audio on stoney
- SR-IOV fixes for vega10
- various powerplay fixes
- lots of code clean up
* 'drm-next-4.14' of git://people.freedesktop.org/~agd5f/linux: (62 commits)
drm/amdgpu/gfx7: fix function name
drm/amd/amdgpu: Disabling Power Gating for Stoney platform
drm/amd/amdgpu: Added a quirk for Stoney platform
drm/amdgpu: jt_size was wrongly counted twice
drm/amdgpu: fix missing endian-safe guard
drm/amdgpu: ignore digest_size when loading sdma fw for raven
drm/amdgpu: Uninitialized variable in amdgpu_ttm_backend_bind()
drm/amd/powerplay: fix coding style in hwmgr.c
drm/amd/powerplay: refine dmesg info under powerplay.
drm/amdgpu: don't finish the ring if not initialized
drm/radeon: Fix preferred typo
drm/amdgpu: Fix preferred typo
drm/radeon: Fix stolen typo
drm/amdgpu: Fix stolen typo
drm/amd/powerplay: fix coccinelle warnings in vega10_hwmgr.c
drm/amdgpu: set gfx_v9_0_ip_funcs as static
drm/radeon: switch to drm_*{get,put} helpers
drm/amdgpu: switch to drm_*{get,put} helpers
drm/amd/powerplay: add CZ profile support
drm/amd/powerplay: fix PSI not enabled by kmd
...
Dave Airlie [Wed, 16 Aug 2017 21:33:41 +0000 (07:33 +1000)]
Merge tag 'drm-misc-next-2017-08-16' of git://anongit.freedesktop.org/git/drm-misc into drm-next
UAPI Changes:
- vc4: Allow userspace to dictate rendering order in submit_cl ioctl (Eric)
Cross-subsystem Changes:
- vboxvideo: One of Cihangir's patches applies to vboxvideo which is maintained
in staging
Core Changes:
- atomic_legacy_backoff is officially killed (Daniel)
- Extract drm_device.h (Daniel)
- Unregister drm device on unplug (Daniel)
- Rename deprecated drm_*_(un)?reference functions to drm_*_{get|put} (Cihangir)
Driver Changes:
- vc4: Error/destroy path cleanups, log level demotion, edid leak (Eric)
- various: Make various drm_*_funcs structs const (Bhumika)
- tinydrm: add support for LEGO MINDSTORMS EV3 LCD (David)
- various: Second half of .dumb_{map_offset|destroy} defaults set (Noralf)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Eric Anholt <eric@anholt.net> Cc: Bhumika Goyal <bhumirks@gmail.com> Cc: Cihangir Akturk <cakturk@gmail.com> Cc: David Lechner <david@lechnology.com> Cc: Noralf Trønnes <noralf@tronnes.org>
* tag 'drm-misc-next-2017-08-16' of git://anongit.freedesktop.org/git/drm-misc: (50 commits)
drm/gem-cma-helper: Remove drm_gem_cma_dumb_map_offset()
drm/virtio: Use the drm_driver.dumb_destroy default
drm/bochs: Use the drm_driver.dumb_destroy default
drm/mgag200: Use the drm_driver.dumb_destroy default
drm/exynos: Use .dumb_map_offset and .dumb_destroy defaults
drm/msm: Use the drm_driver.dumb_destroy default
drm/ast: Use the drm_driver.dumb_destroy default
drm/qxl: Use the drm_driver.dumb_destroy default
drm/udl: Use the drm_driver.dumb_destroy default
drm/cirrus: Use the drm_driver.dumb_destroy default
drm/tegra: Use .dumb_map_offset and .dumb_destroy defaults
drm/gma500: Use .dumb_map_offset and .dumb_destroy defaults
drm/mxsfb: Use .dumb_map_offset and .dumb_destroy defaults
drm/meson: Use .dumb_map_offset and .dumb_destroy defaults
drm/kirin: Use .dumb_map_offset and .dumb_destroy defaults
drm/vc4: Continue the switch to drm_*_put() helpers
drm/vc4: Fix leak of HDMI EDID
dma-buf: fix reservation_object_wait_timeout_rcu to wait correctly v2
dma-buf: add reservation_object_copy_fences (v2)
drm/tinydrm: add support for LEGO MINDSTORMS EV3 LCD
...
projects / mirror_ubuntu-eoan-kernel.git / log