Tegra processors prior to Tegra186 used APB DMA for I2C requiring
CONFIG_TEGRA20_APB_DMA=y while Tegra186 and later use GPC DMA requiring
CONFIG_TEGRA186_GPC_DMA=y.
The check for if the processor uses APB DMA is inverted and so the wrong
DMA config options are checked.
This means if CONFIG_TEGRA20_APB_DMA=y but CONFIG_TEGRA186_GPC_DMA=n
with a Tegra186 or later processor the driver will incorrectly think DMA is
enabled and attempt to request DMA channels that will never be availible,
leaving the driver in a perpetual EPROBE_DEFER state.
Fixes: 48cb6356fae1 ("i2c: tegra: Add GPCDMA support") Signed-off-by: Parker Newman <pnewman@connecttech.com> Acked-by: Andi Shyti <andi.shyti@kernel.org> Acked-by: Akhil R <akhilrajeev@nvidia.com> Link: https://lore.kernel.org/r/fcfcf9b3-c8c4-9b34-2ff8-cd60a3d490bd@connecttech.com Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The controller may be shared with other port, for example the firmware.
Handle the interrupt from other sources will cause crash since some
data are not initialized. So only handle the interrupt of the driver's
transfer and discard others.
Fixes: d62fbdb99a85 ("i2c: add support for HiSilicon I2C controller") Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Link: https://lore.kernel.org/r/20230801124625.63587-1-yangyicong@huawei.com Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
iproc_i2c_rd_reg() and iproc_i2c_wr_reg() are called from both
interrupt context (e.g. bcm_iproc_i2c_isr) and process context
(e.g. bcm_iproc_i2c_suspend). Therefore, interrupts should be
disabled to avoid potential deadlock. To prevent this scenario,
use spin_lock_irqsave().
Fixes: 9a1038728037 ("i2c: iproc: add NIC I2C support") Signed-off-by: Chengfeng Ye <dg573847474@gmail.com> Acked-by: Ray Jui <ray.jui@broadcom.com> Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
With deferred close we can have closes that race with lease breaks,
and so with the current checks for whether to send the lease response,
oplock_response(), this can mean that an unmount (kill_sb) can occur
just before we were checking if the tcon->ses is valid. See below:
To fix this change the ordering of the checks before sending the oplock_response
to first check if the openFileList is empty.
Fixes: da787d5b7498 ("SMB3: Do not send lease break acknowledgment if all file handles have been closed") Suggested-by: Bharath SM <bharathsm@microsoft.com> Reviewed-by: Bharath SM <bharathsm@microsoft.com> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
mlx5_vdpa_destroy_mr can be called from .set_map with data ASID after
the control virtqueue ASID iotlb has been populated. The control vq
iotlb must not be cleared, since it will not be populated again.
So call the ASID aware destroy function which makes sure that the
right vq resource is destroyed.
Fixes: 8fcd20c30704 ("vdpa/mlx5: Support different address spaces for control and data") Signed-off-by: Eugenio Pérez <eperezma@redhat.com> Reviewed-by: Gal Pressman <gal@nvidia.com>
Message-Id: <20230802171231.11001-5-dtatulea@nvidia.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The mr->initialized flag is shared between the control vq and data vq
part of the mr init/uninit. But if the control vq and data vq get placed
in different ASIDs, it can happen that initializing the control vq will
prevent the data vq mr from being initialized.
This patch consolidates the control and data vq init parts into their
own init functions. The mr->initialized will now be used for the data vq
only. The control vq currently doesn't need a flag.
The uninitializing part is also taken care of: mlx5_vdpa_destroy_mr got
split into data and control vq functions which are now also ASID aware.
Fixes: 8fcd20c30704 ("vdpa/mlx5: Support different address spaces for control and data") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Eugenio Pérez <eperezma@redhat.com> Reviewed-by: Gal Pressman <gal@nvidia.com>
Message-Id: <20230802171231.11001-3-dtatulea@nvidia.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The IRQ injection work used spin_lock_irq() to protect the
scheduling of the softirq, but spin_lock_bh() should be
used.
With spin_lock_irq(), we noticed delay of more than 6
seconds between the time a NAPI polling work is scheduled
and the time it is executed.
Fixes: c8a6153b6c59 ("vduse: Introduce VDUSE - vDPA Device in Userspace") Cc: xieyongji@bytedance.com Suggested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Message-Id: <20230705114505.63274-1-maxime.coquelin@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Xie Yongji <xieyongji@bytedance.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
vm_dev has a separate lifecycle because it has a 'struct device'
embedded. Thus, having a release callback for it is correct.
Allocating the vm_dev struct with devres totally breaks this protection,
though. Instead of waiting for the vm_dev release callback, the memory
is freed when the platform_device is removed. Resulting in a
use-after-free when finally the callback is to be called.
To easily see the problem, compile the kernel with
CONFIG_DEBUG_KOBJECT_RELEASE and unbind with sysfs.
The fix is easy, don't use devres in this case.
Found during my research about object lifetime problems.
Fixes: 7eb781b1bbb7 ("virtio_mmio: add cleanup for virtio_mmio_probe") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Message-Id: <20230629120526.7184-1-wsa+renesas@sang-engineering.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If a task creates a new block group and that block group becomes unused
before we finish its creation, at btrfs_create_pending_block_groups(),
then when btrfs_mark_bg_unused() is called against the block group, we
assume that the block group is currently in the list of block groups to
reclaim, and we move it out of the list of new block groups and into the
list of unused block groups. This has two consequences:
1) We move it out of the list of new block groups associated to the
current transaction. So the block group creation is not finished and
if we attempt to delete the bg because it's unused, we will not find
the block group item in the extent tree (or the new block group tree),
its device extent items in the device tree etc, resulting in the
deletion to fail due to the missing items;
2) We don't increment the reference count on the block group when we
move it to the list of unused block groups, because we assumed the
block group was on the list of block groups to reclaim, and in that
case it already has the correct reference count. However the block
group was on the list of new block groups, in which case no extra
reference was taken because it's local to the current task. This
later results in doing an extra reference count decrement when
removing the block group from the unused list, eventually leading the
reference count to 0.
This second case was caught when running generic/297 from fstests, which
produced the following assertion failure and stack trace:
Fix this by adding a runtime flag to the block group to tell that the
block group is still in the list of new block groups, and therefore it
should not be moved to the list of unused block groups, at
btrfs_mark_bg_unused(), until the flag is cleared, when we finish the
creation of the block group at btrfs_create_pending_block_groups().
Fixes: a9f189716cf1 ("btrfs: move out now unused BG from the reclaim list") CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
An unused block group is easy to remove to free up space and should be
reclaimed fast. Such block group can often already be a target of the
reclaim process. As we check list_empty(&bg->bg_list), we keep it in the
reclaim list. That block group is never reclaimed until the file system
is filled e.g. up to 75%.
Instead, we can move unused block group to the unused list and delete it
fast.
Fixes: 18bb8bbf13c1 ("btrfs: zoned: automatically reclaim zones") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Generic fbdev drivers use the apertures field in struct fb_info to
control ownership of the framebuffer memory and graphics device. Do
not set the values in hyperv-fb.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://patchwork.freedesktop.org/patch/msgid/20221219160516.23436-9-tzimmermann@suse.de
Stable-dep-of: 5ae3716cfdcd ("video/aperture: Only remove sysfb on the default vga pci device") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why] hdcp are enabled for asics from raven. for old asics
which hdcp are not enabled, hdcp_workqueue are null. some
access to hdcp work queue are not guarded with pointer check.
[How] add hdcp_workqueue pointer check before access workqueue.
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Hersen Wu <hersenxs.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why]
multiple display hdcp are enabled within event_property_validate,
event_property_update by looping all displays on mst hub. when
one of display on mst hub in unplugged or disabled, hdcp are
disabled for all displays on mst hub within hdcp_reset_display
by looping all displays of mst link. for displays still active,
their encryption status are off. kernel driver will not run hdcp
authentication again. therefore, hdcp are not enabled automatically.
[How]
within is_content_protection_different, check drm_crtc_state changes
of all displays on mst hub, if need, triger hdcp_update_display to
re-run hdcp authentication.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: hersen wu <hersenxs.wu@amd.com> Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: cdff36a0217a ("drm/amd/display: fix access hdcp_workqueue assert") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why]
connector hdcp properties are lost after display is
unplgged from mst hub. connector is destroyed with
dm_dp_mst_connector_destroy. when display is plugged
back, hdcp is not desired and it wouldnt be enabled.
[How]
save hdcp properties into hdcp_work within
amdgpu_dm_atomic_commit_tail. If the same display is
plugged back with same display index, its hdcp
properties will be retrieved from hdcp_work within
dm_dp_mst_get_modes.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: hersen wu <hersenxs.wu@amd.com> Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: cdff36a0217a ("drm/amd/display: fix access hdcp_workqueue assert") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
igc_configure_rx_ring() function will be called as part of XDP program
setup. If Rx hardware timestamp is enabled prio to XDP program setup,
this timestamp enablement will be overwritten when buffer size is
written into SRRCTL register.
Thus, this commit read the register value before write to SRRCTL
register. This commit is tested by using xdp_hw_metadata bpf selftest
tool. The tool enables Rx hardware timestamp and then attach XDP program
to igc driver. It will display hardware timestamp of UDP packet with
port number 9092. Below are detail of test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
Command on Link Partner:
echo -n skb | nc -u -q1 <destination IPv4 addr> 9092
Result before this patch:
skb hwtstamp is not found!
Optionally, read PHC to confirm the values obtained are almost the same:
Command:
sudo ./testptp -d /dev/ptp0 -g
Result:
clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023
Fixes: fc9df2a0b520 ("igc: Enable RX via AF_XDP zero-copy") Cc: <stable@vger.kernel.org> # 5.14+ Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com> Tested-by: Jesper Dangaard Brouer <brouer@redhat.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When ring_buffer_swap_cpu was called during resize process,
the cpu buffer was swapped in the middle, resulting in incorrect state.
Continuing to run in the wrong state will result in oops.
This issue can be easily reproduced using the following two scripts:
/tmp # cat test1.sh
//#! /bin/sh
for i in `seq 0 100000`
do
echo 2000 > /sys/kernel/debug/tracing/buffer_size_kb
sleep 0.5
echo 5000 > /sys/kernel/debug/tracing/buffer_size_kb
sleep 0.5
done
/tmp # cat test2.sh
//#! /bin/sh
for i in `seq 0 100000`
do
echo irqsoff > /sys/kernel/debug/tracing/current_tracer
sleep 1
echo nop > /sys/kernel/debug/tracing/current_tracer
sleep 1
done
/tmp # ./test1.sh &
/tmp # ./test2.sh &
A typical oops log is as follows, sometimes with other different oops logs.
After analysis, the seq of the error is as follows [1-5]:
int ring_buffer_resize(struct trace_buffer *buffer, unsigned long size,
int cpu_id)
{
for_each_buffer_cpu(buffer, cpu) {
cpu_buffer = buffer->buffers[cpu];
//1. get cpu_buffer, aka cpu_buffer(A)
...
...
schedule_work_on(cpu,
&cpu_buffer->update_pages_work);
//2. 'update_pages_work' is queue on 'cpu', cpu_buffer(A) is passed to
// update_pages_handler, do the update process, set 'update_done' in
// complete(&cpu_buffer->update_done) and to wakeup resize process.
//---->
//3. Just at this moment, ring_buffer_swap_cpu is triggered,
//cpu_buffer(A) be swaped to cpu_buffer(B), the max_buffer.
//ring_buffer_swap_cpu is called as the 'Call trace' below.
/* wait for all the updates to complete */
for_each_buffer_cpu(buffer, cpu) {
cpu_buffer = buffer->buffers[cpu];
//4. get cpu_buffer, cpu_buffer(B) is used in the following process,
//the state of cpu_buffer(A) and cpu_buffer(B) is totally wrong.
//for example, cpu_buffer(A)->update_done will leave be set 1, and will
//not 'wait_for_completion' at the next resize round.
if (!cpu_buffer->nr_pages_to_update)
continue;
if (cpu_online(cpu))
wait_for_completion(&cpu_buffer->update_done);
cpu_buffer->nr_pages_to_update = 0;
}
...
}
//5. the state of cpu_buffer(A) and cpu_buffer(B) is totally wrong,
//Continuing to run in the wrong state, then oops occurs.
Link: https://lore.kernel.org/linux-trace-kernel/202307191558478409990@zte.com.cn Signed-off-by: Chen Lin <chen.lin5@zte.com.cn> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In function ‘fortify_memcpy_chk’,
inlined from ‘get_conn_info_complete’ at net/bluetooth/mgmt.c:7281:2:
include/linux/fortify-string.h:592:25: error: call to
‘__read_overflow2_field’ declared with attribute warning: detected read
beyond size of field (2nd parameter); maybe use struct_group()?
[-Werror=attribute-warning]
592 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
This is due to the wrong member is used for memcpy(). Use correct one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
As per the generic KASAN code in mm/kasan, disable KCOV with
KCOV_INSTRUMENT := n in the makefile.
This fixes a ppc64 boot hang when KCOV and KASAN are enabled.
kasan_early_init() gets called before a PACA is initialised, but the
KCOV hook expects a valid PACA.
Suggested-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Benjamin Gray <bgray@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230710044143.146840-1-bgray@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG GZ301V series which uses an SPI connected Cirrus amp.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev> Link: https://lore.kernel.org/r/20230706223323.30871-2-luke@ljones.dev Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG GA402X series which uses an I2C connected Cirrus amp.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev> Link: https://lore.kernel.org/r/20230704044619.19343-3-luke@ljones.dev Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG GV601V series which uses an I2C connected Cirrus amp.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev> Link: https://lore.kernel.org/r/20230704044619.19343-2-luke@ljones.dev Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The variable codec->regmap is often protected by the lock
codec->regmap_lock when is accessed. However, it is accessed without
holding the lock when is accessed in snd_hdac_regmap_sync():
if (codec->regmap)
In my opinion, this may be a harmful race, because if codec->regmap is
set to NULL right after the condition is checked, a null-pointer
dereference can occur in the called function regcache_sync():
map->lock(map->lock_arg); --> Line 360 in drivers/base/regmap/regcache.c
To fix this possible null-pointer dereference caused by data race, the
mutex_lock coverage is extended to protect the if statement as well as the
function call to regcache_sync().
[ Note: the lack of the regmap_lock itself is harmless for the current
codec driver implementations, as snd_hdac_regmap_sync() is only for
PM runtime resume that is prohibited during the codec probe.
But the change makes the whole code more consistent, so it's merged
as is -- tiwai ]
Reported-by: BassCheck <bass@buaa.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Link: https://lore.kernel.org/r/20230703031016.1184711-1-islituo@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
These models use NSIWAY amplifiers for internal speaker, but cannot put
sound outside from these amplifiers. So eapd verbs are needed to initialize
the amplifiers. They can be added during boot to get working sound out
of internal speaker.
In a previous commit 2681631c2973 ("fs/ntfs3: Add null pointer check to
attr_load_runs_vcn"), ni can be NULL in attr_load_runs_vcn(), and thus it
should be checked before being used.
However, in the call stack of this commit, mft_ni in mi_read() is
aliased with ni in attr_load_runs_vcn(), and it is also used in
mi_read() at two places:
mi_read()
rw_lock = &mft_ni->file.run_lock -> No check
attr_load_runs_vcn(mft_ni, ...)
ni (namely mft_ni) is checked in the previous commit
attr_load_runs_vcn(..., &mft_ni->file.run) -> No check
Thus, to avoid possible null-pointer dereferences, the related checks
should be added.
These bugs are reported by a static analysis tool implemented by myself,
and they are found by extending a known bug fixed in the previous commit.
Thus, they could be theoretical bugs.
Signed-off-by: Jia-Ju Bai <baijiaju@buaa.edu.cn> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
ni_create_attr_list uses WARN_ON to catch error cases while generating
attribute list, which only prints out stack trace and may not be enough.
This repalces them with more proper error handling flow.
Signed-off-by: Edward Lo <loyuantsung@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
fence Decrements the reference count before exiting.
Avoid Race Vulnerabilities for fence use-after-free.
v2 (chk): actually fix the use after free and not just move it.
Signed-off-by: shanzhulig <shanzhulig@gmail.com> Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Adding the device ID from the Asus Ally gets the bluetooth working
on the device.
Signed-off-by: Matthew Anderson <ruinairas1992@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Intel Barlow Ridge discrete USB4 host router has the same limitation as
the previous generations so make sure the USB3 bandwidth limitation
quirk is applied to Barlow Ridge too.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Intel Barlow Ridge is the first USB4 v2 controller from Intel. The
controller exposes standard USB4 PCI class ID in typical configurations,
however there is a way to configure it so that it uses a special class
ID to allow using s different driver than the Windows inbox one. For
this reason add the Barlow Ridge PCI ID to the Linux driver too so that
the driver can attach regardless of the class ID.
Tested-by: Pengfei Xu <pengfei.xu@intel.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When nonstatic_release_resource_db() frees all resources associated
with an PCMCIA socket, it forgets to free socket_data too, causing
a memory leak observable with kmemleak:
To fix these possible data races, the lock sdp->sd_tune.gt_spin is
acquired before accessing the fields of gfs2_tune and released after these
accesses.
Further changes by Andreas:
- Don't hold the spin lock over the seq_printf operations.
Reported-by: BassCheck <bass@buaa.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
USB PHY DPDM wakeup bit is enabled by default, when USB wakeup
is not required(/sys/.../wakeup is disabled), this bit should be
disabled, otherwise we will have unexpected wakeup if do USB device
connect/disconnect while system sleep.
This bit can be enabled for both host and device mode.
Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230517081907.3410465-3-xu.yang_2@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use dedicated imx8ulp usb compatible to remove QoS request
since imx8ulp has no such limitation of imx7ulp: DMA will
not work if system enters idle.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230530104007.1294702-2-xu.yang_2@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
ISOC transfers expect a certain cadence of requests being queued. Not
keeping up with the expected rate of requests results in missed ISOC
transfers (EXDEV). The application layer may or may not produce video
frames to match this expectation, so uvc gadget driver must handle cases
where the application is not queuing up buffers fast enough to fulfill
ISOC requirements.
Currently, uvc gadget driver waits for new video buffer to become available
before queuing up usb requests. With this patch the gadget driver queues up
0 length usb requests whenever there are no video buffers available. The
USB controller's complete callback is used as the limiter for how quickly
the 0 length packets will be queued. Video buffers are still queued as
soon as they become available.
When serial console over USB is enabled, gs_console_connect
queues gs_console_work, where it acquires the spinlock and
queues the usb request, and this request goes to gadget layer.
Now consider a situation where gadget layer prints something
to dmesg, this will eventually call gs_console_write() which
requires cons->lock. And this causes spinlock recursion. Avoid
this by excluding usb_ep_queue from the spinlock.
From the experiments with camera sensors using SGRBG10_1X10/3280x2464 and
SRGGB10_1X10/3280x2464 formats, it becomes clear that on sdm845 and sm8250
VFE outputs the lines padded to a length multiple of 16 bytes. As in the
current driver the value of the bpl_alignment is set to 8 bytes, the frames
captured in formats with the bytes-per-line value being not a multiple of
16 get corrupted.
Set the bpl_alignment of the camss video output device to 16 for sdm845 and
sm8250 to fix that.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Getting below error when using KCSAN to check the driver. Adding lock to
protect parameter num_rdy when getting the value with function:
v4l2_m2m_num_src_bufs_ready/v4l2_m2m_num_dst_bufs_ready.
kworker/u16:3: [name:report&]BUG: KCSAN: data-race in v4l2_m2m_buf_queue
kworker/u16:3: [name:report&]
kworker/u16:3: [name:report&]read-write to 0xffffff8105f35b94 of 1 bytes by task 20865 on cpu 7:
kworker/u16:3: v4l2_m2m_buf_queue+0xd8/0x10c
Signed-off-by: Pina Chen <pina.chen@mediatek.com> Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Ensure child node references are decremented properly in the error path.
Signed-off-by: Lu Hongfei <luhongfei@vivo.com> Link: https://lore.kernel.org/r/20230525111705.3055-1-luhongfei@vivo.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Returning early from stm32_usart_serial_remove() results in a resource
leak as several cleanup functions are not called. The driver core ignores
the return value and there is no possibility to clean up later.
uart_remove_one_port() only returns non-zero if there is some
inconsistency (i.e. stm32_usart_driver.state[port->line].uart_port == NULL).
This should never happen, and even if it does it's a bad idea to exit
early in the remove callback without cleaning up.
This prepares changing the prototype of struct platform_driver::remove to
return void. See commit 5c5a7680e67b ("platform: Provide a remove callback
that returns no value") for further details about this quest.
Don't collect exiting session in smb2_reconnect_server(), because it
will be released soon.
Note that the exiting session will stay in server->smb_ses_list until
it complete the cifs_free_ipc() and logoff() and then delete itself
from the list.
Signed-off-by: Winston Wen <wentao@uniontech.com> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
This fixes the following warning reported by kernel test robot
fs/smb/client/cifsfs.c:982 cifs_smb3_do_mount() warn: possible
memory leak of 'cifs_sb'
Link: https://lore.kernel.org/all/202306170124.CtQqzf0I-lkp@intel.com/ Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The shutdown is called on reboot/shutdown of the machine.
At this point the firmware tracing cannot be used anymore but in case of
IPC3 it is using and keeping a DMA channel active (dtrace).
For Tiger Lake platforms we have a quirk in place to fix rare reboot issues
when a DMA was active before rebooting the system.
If the tracing is enabled this quirk will be always used and a print
appears on the kernel log which might be misleading or not even correct.
Release the fw tracing before executing the shutdown to make sure that this
known DMA user is cleared away.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20230616100039.378150-4-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why and How]
Add back debug bits enabling RCO for dcn314 as underflow
associated with this change has been resolved
Acked-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Daniel Miess <daniel.miess@amd.com> Reviewed-by: Jun Lei <jun.lei@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[Why]
Hardware implements root clock gating by utilizing the DPP DTO registers
with a special case of DTO enabled, phase = 0, modulo = 1. This
conflicts with our policy to always update the DPPDTO for cases where
it's expected to be disabled.
The pipes unexpectedly enter a higher power state than expected because
of this programming flow.
[How]
Guard the upper layers of HWSS against this hardware quirk with
programming the register with an internal state flag in DCCG.
While technically acting as global state for the DCCG, HWSS shouldn't be
expected to understand the hardware quirk for having DTO disabled
causing more power than DTO enabled with this specific setting.
This also prevents sequencing errors from occuring in the future if
we have to program DPP DTO in multiple locations.
Acked-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Jun Lei <jun.lei@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Previously when destroying a QP/RQ, the result of the firmware
destruction function was ignored and upper layers weren't informed
about the failure.
Which in turn could lead to various problems since when upper layer
isn't aware of the failure it continues its operation thinking that the
related QP/RQ was successfully destroyed while it actually wasn't,
which could lead to the below kernel WARN.
Currently, we return the correct firmware destruction status to upper
layers which in case of the RQ would be mlx5_ib_destroy_wq() which
was already capable of handling RQ destruction failure or in case of
a QP to destroy_qp_common(), which now would actually warn upon qp
destruction failure.
[Description]
- Previously we wanted to apply extra 60us of prefetch for min DCFCLK
(200Mhz), but DCFCLK can be calculated to be 201Mhz which underflows
also without the extra prefetch
- Instead, apply the the extra 60us prefetch for any DCFCLK freq <=
300Mhz
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com> Reviewed-by: Jun Lei <jun.lei@amd.com> Acked-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When using cpu to update page tables, vm update fences are unused.
Install stub fence into these fence pointers instead of NULL
to avoid NULL dereference when calling dma_fence_wait() on them.
Suggested-by: Christian König <christian.koenig@amd.com> Signed-off-by: Lang Yu <Lang.Yu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
An Interrupt Remapping Table (IRT) stores interrupt remapping configuration
for each device. In a normal operation, the AMD IOMMU caches the table
to optimize subsequent data accesses. This requires the IOMMU driver to
invalidate IRT whenever it updates the table. The invalidation process
includes issuing an INVALIDATE_INTERRUPT_TABLE command following by
a COMPLETION_WAIT command.
However, there are cases in which the IRT is updated at a high rate.
For example, for IOMMU AVIC, the IRTE[IsRun] bit is updated on every
vcpu scheduling (i.e. amd_iommu_update_ga()). On system with large
amount of vcpus and VFIO PCI pass-through devices, the invalidation
process could potentially become a performance bottleneck.
Introducing a new kernel boot option:
amd_iommu=irtcachedis
which disables IRTE caching by setting the IRTCachedis bit in each IOMMU
Control register, and bypass the IRT invalidation process.
Adds the USB and Bluetooth IDs for the Logitech G915 TKL keyboard, for device detection
For this device, this provides battery reporting on top of hid-generic
Reviewed-by: Bastien Nocera <hadess@hadess.net> Signed-off-by: Stuart Hayhurst <stuart.a.hayhurst@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Currently upon a heartbeat failure, we don't know if the failure
is due to firmware hang or due to a bad PCI link. Hence, we
are reading a PCI config space register with a known value (vendor ID)
so we will know which of the two possibilities caused the heartbeat
failure.
If dma_direct_alloc() alloc memory in size of 64MB, the inner function
dma_common_contiguous_remap() will allocate 128KB memory by invoking
the function kmalloc_array(). and the kmalloc_array seems to fail to try to
allocate 128KB mem.
The functionality described in Commit 61bef9e68dca ("ASoC: SOF: Intel: hda: enforce exclusion between HDaudio and SoundWire")
does not seem to be properly implemented with two issues that need to
be corrected.
a) The test used is incorrect when DisplayAudio codecs are not supported.
b) Conversely when only Display Audio codecs can be found, we do want
to start the SoundWire links, if any. That will help add the relevant
topologies and machine descriptors, and identify cases where the
SoundWire information in ACPI needs to be modified with a quirk.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Link: https://lore.kernel.org/r/20230606222529.57156-2-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It is considered good practice to call cpu_relax() in busy loops, see
Documentation/process/volatile-considered-harmful.rst. This can not
only lower CPU power consumption or yield to a hyperthreaded twin
processor, but also allows an architecture to mitigate hardware issues
(e.g. ARM Erratum 754327 for Cortex-A9 prior to r2p0) in the
architecture-specific cpu_relax() implementation.
In addition, cpu_relax() is also a compiler barrier. It is not
immediately obvious that the @op argument "function" will result in an
actual function call (e.g. in case of inlining).
Where a function call is a C sequence point, this is lost on inlining.
Therefore, with agressive enough optimization it might be possible for
the compiler to hoist the:
(val) = op(args);
"load" out of the loop because it doesn't see the value changing. The
addition of cpu_relax() would inhibit this.
As the iopoll helpers lack calls to cpu_relax(), people are sometimes
reluctant to use them, and may fall back to open-coded polling loops
(including cpu_relax() calls) instead.
Fix this by adding calls to cpu_relax() to the iopoll helpers:
- For the non-atomic case, it is sufficient to call cpu_relax() in
case of a zero sleep-between-reads value, as a call to
usleep_range() is a safe barrier otherwise. However, it doesn't
hurt to add the call regardless, for simplicity, and for similarity
with the atomic case below.
- For the atomic case, cpu_relax() must be called regardless of the
sleep-between-reads value, as there is no guarantee all
architecture-specific implementations of udelay() handle this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/45c87bec3397fdd704376807f0eec5cc71be440f.1685692810.git.geert+renesas@glider.be Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
if (!SOF_RT711_JDSRC(sof_sdw_quirk)) is tested in rt711_sdca_add_codec_
device_props(), and we don't add software node to the device if jack
source is not set. We need to do the same test in
sof_sdw_rt711_sdca_exit(), and avoid removing software node if jack
source is not set.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20230602202225.249209-8-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Fix USB-related warnings in prtrvt, prtvt7, prti6q and prtwd2 device trees
by disabling unused usbphynop1 and usbphynop2 USB PHYs and providing proper
configuration for the over-current detection. This fixes the following
warnings with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over current polarity defined
By the way, fix over-current detection on usbotg port for prtvt7, prti6q
and prtwd2 boards. Only prtrvt do not have OC on USB OTG port.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We have SOF and generic ACP support enabled for Vangogh platform
on some machines. Since we have same PCI id used for probing,
add check for machine configuration flag to avoid conflict with
newer pci drivers. Such machine flag has been initialized via
dmi match on few Vangogh based machines. If no flag is
specified probe and register older platform device.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com> Link: https://lore.kernel.org/r/20230530110802.674939-1-venkataprasad.potturu@amd.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
for this SoC and prevent booting it. Public users only have ES2 onwards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Add check to fix the possible array out of bounds violation by
making speed equal to GEN1_CORE_CLK_FREQ when its value is more
than the size of "pcie_gen_freq" array. This array has size of
four but possible speed (CLS) values are from "0 to 0xF". So,
"speed - 1" values are "-1 to 0xE".
Suggested-by: Bjorn Helgaas <helgaas@kernel.org> Signed-off-by: Sumit Gupta <sumitg@nvidia.com> Link: https://lore.kernel.org/lkml/72b9168b-d4d6-4312-32ea-69358df2f2d0@nvidia.com/ Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The type of size is unsigned int, if size is 0x40000000, there will
be an integer overflow, size will be zero after size *= sizeof(uint32_t),
will cause uninitialized memory to be referenced later.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: hackyzh002 <hackyzh002@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
For smu v13_0_2, if the GPU supports xgmi, refer to
commit f5c7e7797060 ("drm/amdgpu: Adjust removal control flow for smu v13_0_2"),
it will run gpu recover in AMDGPU_RESET_FOR_DEVICE_REMOVE mode when removing,
which makes all devices in hive list have hw reset but no resume except the
basic ip blocks, then other ip blocks will not call .hw_fini according to
ip_block.status.hw.
Since psp_free_shared_bufs just includes some software operations, so move
it to psp_sw_fini.
Reviewed-by: Guchun Chen <guchun.chen@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Longlong Yao <Longlong.Yao@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
In commit 7beecaf7d507 ("net: phy: at803x: improve the WOL feature"), it
seems not correct to use a wol_en bit in a 1588 Control Register which is
only available on AR8031/AR8033(share the same phy_id) to determine if WoL
is enabled. Change it back to use AT803X_INTR_ENABLE_WOL for determining
the WoL status which is applicable on all chips supporting wol. Also update
the at803x_set_wol() function to only update the 1588 register on chips
having it. After this change, disabling wol at probe from commit d7cd5e06c9dd ("net: phy: at803x: disable WOL at probe") is no longer
needed. Change it to just disable the WoL bit in 1588 register for
AR8031/AR8033 to be aligned with AT803X_INTR_ENABLE_WOL in probe.
Fixes: 7beecaf7d507 ("net: phy: at803x: improve the WOL feature") Signed-off-by: Li Yang <leoyang.li@nxp.com> Reviewed-by: Viorel Suman <viorel.suman@nxp.com> Reviewed-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Use devm_regulator_get_enable_optional() instead of hand writing it. It
saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: e58f30246c35 ("net: phy: at803x: fix the wol setting functions") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
It's clear that rmbs_lock and sndbufs_lock are aims to protect the
rmbs list or the sndbufs list.
During connection establieshment, smc_buf_get_slot() will always
be invoked, and it only performs read semantics in rmbs list and
sndbufs list.
Based on the above considerations, we replace mutex with rw_semaphore.
Only smc_buf_get_slot() use down_read() to allow smc_buf_get_slot()
run concurrently, other part use down_write() to keep exclusive
semantics.
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 833bac7ec392 ("net/smc: Fix setsockopt and sysctl to specify same buffer size again") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
remove temporary files created by 'mirred_egress_to_ingress_tcp' test
in the cleanup() handler. Also, change variable names to avoid clashing
with globals from lib.sh.
Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Link: https://lore.kernel.org/r/091649045a017fc00095ecbb75884e5681f7025f.1676368027.git.dcaratti@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 5e8670610b93 ("selftests: forwarding: tc_actions: Use ncat instead of nc") Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Kamal Mostafa [Tue, 10 Oct 2023 20:23:53 +0000 (13:23 -0700)]
UBUNTU: Upstream stable to v6.1.46, v6.4.11
BugLink: https://bugs.launchpad.net/bugs/2038969 Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
On system resume, the driver might call it6505_poweron directly if the
runtime PM hasn't been enabled. In such case, pm_runtime_get_if_in_use
will always return 0 because dev->power.runtime_status stays at
RPM_SUSPENDED, and the IRQ will never be handled.
Use it6505->powered from the driver struct fixes this because it always
gets updated when it6505_poweron is called.
Fixes: 5eb9a4314053 ("drm/bridge: it6505: Guard bridge power in IRQ handler") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230727100131.2338127-1-treapking@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Some test cases check that the group timer is (or isn't) 0. Instead of
grepping for "0.00" grep for " 0.00" as the former can also match
"260.00" which is the default group membership interval.
Fixes: b6d00da08610 ("selftests: forwarding: Add bridge MDB test") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-18-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The test relies on 'nc' being the netcat version from the nmap project.
While this seems to be the case on Fedora, it is not the case on Ubuntu,
resulting in failures such as [1].
Fix by explicitly using the 'ncat' utility from the nmap project and the
skip the test in case it is not installed.
The selftest relies on iproute2 changes present in version 6.3, but the
test does not check for it, resulting in error:
# ./bridge_mdb.sh
INFO: # Host entries configuration tests
TEST: Common host entries configuration tests (IPv4) [FAIL]
Managed to add IPv4 host entry with a filter mode
TEST: Common host entries configuration tests (IPv6) [FAIL]
Managed to add IPv6 host entry with a filter mode
TEST: Common host entries configuration tests (L2) [FAIL]
Managed to add L2 host entry with a filter mode
INFO: # Port group entries configuration tests - (*, G)
Command "replace" is unknown, try "bridge mdb help".
[...]
Fix by skipping the test if iproute2 is too old.
Fixes: b6d00da08610 ("selftests: forwarding: Add bridge MDB test") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/6b04b2ba-2372-6f6b-3ac8-b7cba1cfae83@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-4-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The BUILD_VDSO macro was incorrectly spelled as BULID_VDSO in
asm/linkage.h. This causes the !defined(BULID_VDSO) directive to always
evaluate to true.
Correct the spelling to BUILD_VDSO.
Fixes: bea75b33895f ("x86/Kconfig: Introduce function padding") Signed-off-by: Jinghao Jia <jinghao@linux.ibm.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Randy Dunlap <rdunlap@infradead.org> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/20230808182353.76218-1-jinghao@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
folio->_mapcount is overloaded in SLAB, so folio_mapped() has to be done
after folio_test_slab() is checked. Otherwise slab folio might be treated
as a mapped folio leading to false 'Someone maps the hwpoison page' error
info.
Link: https://lkml.kernel.org/r/20230727115643.639741-4-linmiaohe@huawei.com Fixes: 230ac719c500 ("mm/hwpoison: don't try to unpoison containment-failed pages") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If unpoison_memory() fails to clear page hwpoisoned flag, return value ret
is expected to be -EBUSY. But when get_hwpoison_page() returns 1 and
fails to clear page hwpoisoned flag due to races, return value will be
unexpected 1 leading to users being confused. And there's a code smell
that the variable "ret" is used not only to save the return value of
unpoison_memory(), but also the return value from get_hwpoison_page().
Make a further cleanup by using another auto-variable solely to save the
return value of get_hwpoison_page() as suggested by Naoya.
Link: https://lkml.kernel.org/r/20230727115643.639741-3-linmiaohe@huawei.com Fixes: bf181c582588 ("mm/hwpoison: fix unpoison_memory()") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Patch series "Fix hugetlb free path race with memory errors".
In the discussion of Jiaqi Yan's series "Improve hugetlbfs read on
HWPOISON hugepages" the race window was discovered.
https://lore.kernel.org/linux-mm/20230616233447.GB7371@monkey/
Freeing a hugetlb page back to low level memory allocators is performed
in two steps.
1) Under hugetlb lock, remove page from hugetlb lists and clear destructor
2) Outside lock, allocate vmemmap if necessary and call low level free
Between these two steps, the hugetlb page will appear as a normal
compound page. However, vmemmap for tail pages could be missing.
If a memory error occurs at this time, we could try to update page
flags non-existant page structs.
A much more detailed description is in the first patch.
The first patch addresses the race window. However, it adds a
hugetlb_lock lock/unlock cycle to every vmemmap optimized hugetlb page
free operation. This could lead to slowdowns if one is freeing a large
number of hugetlb pages.
The second path optimizes the update_and_free_pages_bulk routine to only
take the lock once in bulk operations.
The second patch is technically not a bug fix, but includes a Fixes tag
and Cc stable to avoid a performance regression. It can be combined with
the first, but was done separately make reviewing easier.
This patch (of 2):
Freeing a hugetlb page and releasing base pages back to the underlying
allocator such as buddy or cma is performed in two steps:
- remove_hugetlb_folio() is called to remove the folio from hugetlb
lists, get a ref on the page and remove hugetlb destructor. This
all must be done under the hugetlb lock. After this call, the page
can be treated as a normal compound page or a collection of base
size pages.
- update_and_free_hugetlb_folio() is called to allocate vmemmap if
needed and the free routine of the underlying allocator is called
on the resulting page. We can not hold the hugetlb lock here.
One issue with this scheme is that a memory error could occur between
these two steps. In this case, the memory error handling code treats
the old hugetlb page as a normal compound page or collection of base
pages. It will then try to SetPageHWPoison(page) on the page with an
error. If the page with error is a tail page without vmemmap, a write
error will occur when trying to set the flag.
Address this issue by modifying remove_hugetlb_folio() and
update_and_free_hugetlb_folio() such that the hugetlb destructor is not
cleared until after allocating vmemmap. Since clearing the destructor
requires holding the hugetlb lock, the clearing is done in
remove_hugetlb_folio() if the vmemmap is present. This saves a
lock/unlock cycle. Otherwise, destructor is cleared in
update_and_free_hugetlb_folio() after allocating vmemmap.
Note that this will leave hugetlb pages in a state where they are marked
free (by hugetlb specific page flag) and have a ref count. This is not
a normal state. The only code that would notice is the memory error
code, and it is set up to retry in such a case.
A subsequent patch will create a routine to do bulk processing of
vmemmap allocation. This will eliminate a lock/unlock cycle for each
hugetlb page in the case where we are freeing a large number of pages.
Link: https://lkml.kernel.org/r/20230711220942.43706-1-mike.kravetz@oracle.com Link: https://lkml.kernel.org/r/20230711220942.43706-2-mike.kravetz@oracle.com Fixes: ad2fa3717b74 ("mm: hugetlb: alloc the vmemmap pages associated with each HugeTLB page") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Tested-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: James Houghton <jthoughton@google.com> Cc: Jiaqi Yan <jiaqiyan@google.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
We encountered many kernel exceptions of VM_BUG_ON(zspage->isolated ==
0) in dec_zspage_isolation() and BUG_ON(!pages[1]) in zs_unmap_object()
lately. This issue only occurs when migration and reclamation occur at
the same time.
With our memory stress test, we can reproduce this issue several times
a day. We have no idea why no one else encountered this issue. BTW,
we switched to the new kernel version with this defect a few months
ago.
Since fullness and isolated share the same unsigned int, modifications of
them should be protected by the same lock.
[andrew.yang@mediatek.com: move comment] Link: https://lkml.kernel.org/r/20230727062910.6337-1-andrew.yang@mediatek.com Link: https://lkml.kernel.org/r/20230721063705.11455-1-andrew.yang@mediatek.com Fixes: c4549b871102 ("zsmalloc: remove zspage isolation for migration") Signed-off-by: Andrew Yang <andrew.yang@mediatek.com> Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
A switch from OSI to PC mode is only possible if all CPUs other than the
calling one are OFF, either through a call to CPU_OFF or not yet booted.
Currently OSI mode is enabled before power domains are created. In cases
where CPUidle states are not using hierarchical CPU topology the bail out
path tries to switch back to PC mode which gets denied by firmware since
other CPUs are online at this point and creates inconsistent state as
firmware is in OSI mode and Linux in PC mode.
This change moves enabling OSI mode after power domains are created,
this would makes sure that hierarchical CPU topology is used before
switching firmware to OSI mode.
Cc: stable@vger.kernel.org Fixes: 70c179b49870 ("cpuidle: psci: Allow PM domain to be initialized even if no OSI mode") Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Even if sdhci_pltfm_pmops is specified for PM, this driver doesn't apply
sdhci_pltfm, so the structure is not correctly referenced in PM functions.
This applies sdhci_pltfm to this driver to fix this issue.
- Call sdhci_pltfm_init() instead of sdhci_alloc_host() and
other functions that covered by sdhci_pltfm.
- Move ops and quirks to sdhci_pltfm_data
- Replace sdhci_priv() with own private function sdhci_f_sdh30_priv().
Fixes: 87a507459f49 ("mmc: sdhci: host: add new f_sdh30") Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230630004533.26644-1-hayashi.kunihiko@socionext.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The ACPI device CSC3556 is a Cirrus Logic CS35L56 mono amplifier which
is used in multiples, and can be connected either to I2C or SPI.
There will be multiple instances under the same Device() node. Add it
to ignore_serial_bus_ids and handle it in the serial-multi-instantiate
driver.
There can be a 5th I2cSerialBusV2, but this is an alias address and doesn't
represent a real device. Ignore this by having a dummy 5th entry in the
serial-multi-instantiate instance list with the name of a non-existent
driver, on the same pattern as done for bsg2150.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com> Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lore.kernel.org/r/20230728111345.7224-1-rf@opensource.cirrus.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The current code assumes that the CSC3551(multiple cs35l41) always have
its interrupt pin connected to GPIO thus the IRQ can be acquired with
acpi_dev_gpio_irq_get. However on some newer laptop models this is no
longer the case as they have the CSC3551's interrupt pin connected to
APIC. This causes smi_i2c_probe to fail on these machines.
To support these machines, a new macro IRQ_RESOURCE_AUTO was introduced
for cs35l41 smi_node, and smi_get_irq function was modified so it tries
to get GPIO irq resource first and if failed, tries to get
APIC irq resource for cs35l41.
This patch affects only the cs35l41's probing and brings no negative
influence on machines that indeed have the cs35l41's interrupt pin
connected to GPIO.
Signed-off-by: David Xu <xuwd1@hotmail.com> Link: https://lore.kernel.org/r/SY4P282MB18350CD8288687B87FFD2243E037A@SY4P282MB1835.AUSP282.PROD.OUTLOOK.COM Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
Fixes: 61d8658b4a43 ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.") Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Signed-off-by: Nilesh Javali <njavali@marvell.com> Link: https://lore.kernel.org/r/20230807093725.46829-1-njavali@marvell.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.") Signed-off-by: Nilesh Javali <njavali@marvell.com> Link: https://lore.kernel.org/r/20230807093725.46829-2-njavali@marvell.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
fnic_clean_pending_aborts() was returning a non-zero value irrespective of
failure or success. This caused the caller of this function to assume that
the device reset had failed, even though it would succeed in most cases. As
a consequence, a successful device reset would escalate to host reset.
Reviewed-by: Sesidhar Baddela <sebaddel@cisco.com> Tested-by: Karan Tilak Kumar <kartilak@cisco.com> Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com> Link: https://lore.kernel.org/r/20230727193919.2519-1-kartilak@cisco.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to decrease the reference count in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Fixes: ee959b00c335 ("SCSI: convert struct class_device to struct device") Signed-off-by: Zhu Wang <wangzhu9@huawei.com> Link: https://lore.kernel.org/r/20230803020230.226903-1-wangzhu9@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>