commit d23f3839fe97d8dce03d ("ARM: dts: DRA7: Add pcie1 dt node for
EP mode") while adding the dt node for EP mode for DRA7 platform,
added rc node for am571x-idk and populated gpios property with
"gpio3 23". However the GPIO_PCIE_SWRST line is actually connected
to "gpio5 18". Fix it here. (The patch adding "gpio3 23" was tested
with another am57x board in EP mode which doesn't rely on reset from
host).
Cc: stable <stable@vger.kernel.org> # 4.14+ Fixes: d23f3839fe97d8dce03d ("ARM: dts: DRA7: Add pcie1 dt node for EP mode") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Logical block size has type unsigned short. That means that it can be at
most 32768. However, there are architectures that can run with 64k pages
(for example arm64) and on these architectures, it may be possible to
create block devices with 64k block size.
For exmaple (run this on an architecture with 64k pages):
Mount will fail with this error because it tries to read the superblock using 2-sector
access:
device-mapper: writecache: I/O is not aligned, sector 2, size 1024, block size 65536
EXT4-fs (dm-0): unable to read superblock
This patch changes the logical block size from unsigned short to unsigned
int to avoid the overflow.
Cc: stable@vger.kernel.org Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
"Note that the microcode update must be aligned on a 16-byte boundary
and the size of the microcode update must be 1-KByte granular"
When early-load Intel microcode is loaded from initramfs, userspace tool
'iucode_tool' has already 16-byte aligned those microcode bits in that
initramfs image. Image that was created something like this:
However, when early-load Intel microcode is loaded from built-in
firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that
16-byte alignment is not guaranteed.
Fix this by forcing all built-in firmware BLOBs to 16-byte alignment.
[ If we end up having other firmware with much bigger alignment
requirements, we might need to introduce some method for the firmware
to specify it, this is the minimal "just increase the alignment a bit
to account for this one special case" patch - Linus ]
A64-OLinuXino uses DCDC1 (VCC-IO) for MMC1 supply. In commit 916b68cfe4b5
("arm64: dts: a64-olinuxino: Enable RTL8723BS WiFi") ALDO2 is set, which is
VCC-PL. Since DCDC1 is always present, the boards are working without a
problem.
The altsetting sanity check in set_sync_ep_implicit_fb_quirk() was
checking for there to be at least one altsetting but then went on to
access the second one, which may not exist.
This could lead to random slab data being used to initialise the sync
endpoint in snd_usb_add_endpoint().
Fixes: c75a8a7ae565 ("ALSA: snd-usb: add support for implicit feedback") Fixes: ca10a7ebdff1 ("ALSA: usb-audio: FT C400 sync playback EP to capture EP") Fixes: 5e35dc0338d8 ("ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204") Fixes: 17f08b0d9aaf ("ALSA: usb-audio: add implicit fb quirk for Axe-Fx II") Fixes: 103e9625647a ("ALSA: usb-audio: simplify set_sync_ep_implicit_fb_quirk") Cc: stable <stable@vger.kernel.org> # 3.5 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200114083953.1106-1-johan@kernel.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
snd_seq_info_timer_read() reads the information of the timer assigned
for each queue, but it's done in a racy way which may lead to UAF as
spotted by syzkaller.
This patch applies the missing q->timer_mutex lock while accessing the
timer object as well as a slight code change to adapt the standard
coding style.
The SGTL5000 VDDIO is connected to the PMIC SW2 output, not to
a fixed 3V3 rail. Describe this correctly in the DT.
Fixes: 52c7a088badd ("ARM: dts: imx6q: Add support for the DHCOM iMX6 SoM and PDK2") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Ludwig Zenz <lzenz@dh-electronics.com> Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
MIC BIAS Internal1 is broken at the moment because we always
enable the internal rbias resistor to the TX2 line (connected to
the headset microphone), rather than enabling the resistor connected
to TX1.
Move the RBIAS code to pm8916_wcd_analog_enable_micbias_int1/2()
to fix this.
Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20200111164006.43074-3-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
MIC BIAS External1 sets pm8916_wcd_analog_enable_micbias_ext1()
as event handler, which ends up in pm8916_wcd_analog_enable_micbias_ext().
But pm8916_wcd_analog_enable_micbias_ext() only handles the POST_PMU
event, which is not specified in the event flags for MIC BIAS External1.
This means that the code in the event handler is never actually run.
Set SND_SOC_DAPM_POST_PMU as the only event for the handler to fix this.
Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20200111164006.43074-2-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Tom Hatskevich reported that we look up "iocp" then, in the called
functions we do a second copy_from_user() and look it up again.
The problem that could cause is:
drivers/message/fusion/mptctl.c
674 /* All of these commands require an interrupt or
675 * are unknown/illegal.
676 */
677 if ((ret = mptctl_syscall_down(iocp, nonblock)) != 0)
^^^^
We take this lock.
678 return ret;
679
680 if (cmd == MPTFWDOWNLOAD)
681 ret = mptctl_fw_download(arg);
^^^
Then the user memory changes and we look up "iocp" again but a different
one so now we are holding the incorrect lock and have a race condition.
682 else if (cmd == MPTCOMMAND)
683 ret = mptctl_mpt_command(arg);
The security impact of this bug is not as bad as it could have been
because these operations are all privileged and root already has
enormous destructive power. But it's still worth fixing.
This patch passes the "iocp" pointer to the functions to avoid the
second lookup. That deletes 100 lines of code from the driver so
it's a nice clean up as well.
Link: https://lore.kernel.org/r/20200114123414.GA7957@kadam Reported-by: Tom Hatskevich <tom2001tom.23@gmail.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
gcc -O3 warns that some local variables are not properly initialized:
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_hang_notify':
drivers/scsi/fnic/vnic_dev.c:511:16: error: 'a0' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[0] = *a0;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:6: note: 'a0' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:10: note: 'a1' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_mac_addr':
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:698:10: note: 'a1' was declared here
u64 a0, a1;
^~
Apparently the code relies on the local variables occupying adjacent memory
locations in the same order, but this is of course not guaranteed.
Use an array of two u64 variables where needed to make it work correctly.
I suspect there is also an endianness bug here, but have not digged in deep
enough to be sure.
Fixes: 5df6d737dd4b ("[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA") Fixes: mmtom ("init/Kconfig: enable -O3 for all arches") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200107201602.4096790-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Check for NULL port data in the modem- and line-status handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe).
Note that the other (stubbed) event handlers qt2_process_xmit_empty()
and qt2_process_flush() would need similar sanity checks in case they
are ever implemented.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver") Cc: stable <stable@vger.kernel.org> # 3.5 Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Check for NULL port data in the control URB completion handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe()).
Fixes: 0ca1268e109a ("USB Serial Keyspan: add support for USA-49WG & USA-28XG") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The driver receives the active port number from the device, but never
made sure that the port number was valid. This could lead to a
NULL-pointer dereference or memory corruption in case a device sends
data for an invalid port.
Check for NULL port data in the shared interrupt and bulk completion
callbacks to avoid dereferencing a NULL pointer in case a device sends
data for a port device which isn't bound to a driver (e.g. due to a
malicious device having unexpected endpoints or after an allocation
failure on port probe).
Check for NULL port data in reset_resume() to avoid dereferencing a NULL
pointer in case the port device isn't bound to a driver (e.g. after a
failed control request at port probe).
Fixes: 1ded7ea47b88 ("USB: ch341 serial: fix port number changed after resume") Cc: stable <stable@vger.kernel.org> # 2.6.30 Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
USB-serial drivers must not be unbound from their ports before the
corresponding USB driver is unbound from the parent interface so
suppress the bind and unbind attributes.
Unbinding a serial driver while it's port is open is a sure way to
trigger a crash as any driver state is released on unbind while port
hangup is handled on the parent USB interface level. Drivers for
multiport devices where ports share a resource such as an interrupt
endpoint also generally cannot handle individual ports going away.
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging
on open() or tiocmset() due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 309a057932ab ("USB: opticon: add rts and cts support") Cc: stable <stable@vger.kernel.org> # 2.6.39 Cc: Martin Jansen <martin.jansen@opticon.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. Unlike other recent Quectel modems, it is possible
to identify the diagnostic interface (bInterfaceProtocol is unique).
Thus, there is no need to check for the number of endpoints or reserve
interfaces. The interface number is still dynamic though, so matching on
interface number is not possible and two entries have to be added to the
table.
Output from usb-devices with all interfaces enabled (order is diag,
nmea, at_port, modem, rmnet and adb):
Bus 004 Device 007: ID 2c7c:0800 Quectel Wireless Solutions Co., Ltd.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.20
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x2c7c Quectel Wireless Solutions Co., Ltd.
idProduct 0x0800
bcdDevice 4.14
iManufacturer 1 Quectel
iProduct 2 LTE-A Module
iSerial 3 40046d60
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 328
bNumInterfaces 6
bConfigurationValue 1
iConfiguration 4 DIAG_SER_RMNET
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 224mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 48
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 05 24 01 00 00
** UNRECOGNIZED: 04 24 02 02
** UNRECOGNIZED: 05 24 06 00 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 9
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 05 24 01 00 00
** UNRECOGNIZED: 04 24 02 02
** UNRECOGNIZED: 05 24 06 00 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 9
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 05 24 01 00 00
** UNRECOGNIZED: 04 24 02 02
** UNRECOGNIZED: 05 24 06 00 00
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x000a 1x 10 bytes
bInterval 9
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 5 CDEV Serial
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 9
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x8e EP 14 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 6
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x0f EP 15 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 2
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 5
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 66
bInterfaceProtocol 1
iInterface 6 ADB Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x89 EP 9 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 42
bNumDeviceCaps 3
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x00000006
Link Power Management (LPM) Supported
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000f
Device can operate at Low Speed (1Mbps)
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 1 micro seconds
bU2DevExitLat 500 micro seconds
** UNRECOGNIZED: 14 10 0a 00 01 00 00 00 00 11 00 00 30 40 0a 00 b0 40 0a 00
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Previous versions of `iio_compute_scan_bytes` only aligned each element
to its own length (i.e. its own natural alignment). Because multiple
consecutive sets of scan elements are buffered this does not work in
case the computed scan bytes do not align with the natural alignment of
the first scan element in the set.
This commit fixes this by aligning the scan bytes to the natural
alignment of the largest scan element in the set.
Fixes: 959d2952d124 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by: Lars Möllendorf <lars.moellendorf@plating.de> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
For some reason, attempting to route audio through QDSP6 on MSM8916
causes the RX interpolation path to get "stuck" after playing audio
a few times. In this situation, the analog codec part is still working,
but the RX path in the digital codec stops working, so you only hear
the analog parts powering up. After a reboot everything works again.
So far I was not able to reproduce the problem when using lpass-cpu.
The downstream kernel driver avoids this by resetting the RX
interpolation path after use. In mainline we do something similar
for the TX decimator (LPASS_CDC_CLK_TX_RESET_B1_CTL), but the
interpolator reset (LPASS_CDC_CLK_RX_RESET_CTL) got lost when the
msm8916-wcd driver was split into analog and digital.
Fix this problem by adding the reset to
msm8916_wcd_digital_enable_interpolator().
Fixes: 150db8c5afa1 ("ASoC: codecs: Add msm8916-wcd digital codec") Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20200105102753.83108-1-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
According to the public S805 datasheet the RESET2 register uses the
following bits for the PIC_DC, PSC and NAND reset lines:
- PIC_DC is at bit 3 (meaning: RESET_VD_RMEM + 3)
- PSC is at bit 4 (meaning: RESET_VD_RMEM + 4)
- NAND is at bit 5 (meaning: RESET_VD_RMEM + 4)
Update the reset IDs of these three reset lines so they don't conflict
with PIC_DC and map to the actual hardware reset lines.
Fixes: 79795e20a184eb ("dt-bindings: reset: Add bindings for the Meson SoC Reset Controller") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On sdm845 devices, during boot we see the following warnings (unless we
have added 'pd_ignore_unused' to the kernel command line):
hlos1_vote_mmnoc_mmu_tbu_sf_gdsc status stuck at 'on'
hlos1_vote_mmnoc_mmu_tbu_hf1_gdsc status stuck at 'on'
hlos1_vote_mmnoc_mmu_tbu_hf0_gdsc status stuck at 'on'
hlos1_vote_aggre_noc_mmu_tbu2_gdsc status stuck at 'on'
hlos1_vote_aggre_noc_mmu_tbu1_gdsc status stuck at 'on'
hlos1_vote_aggre_noc_mmu_pcie_tbu_gdsc status stuck at 'on'
hlos1_vote_aggre_noc_mmu_audio_tbu_gdsc status stuck at 'on'
As the name of these GDSCs suggests, they are "votable" and in downstream
DT, they all have the property "qcom,no-status-check-on-disable", which
means that we should not poll the status bit when we disable them.
Luckily the VOTABLE flag already exists and it does exactly what we need,
so let's make use of it to make the warnings disappear.
Fixes: 06391eddb60a ("clk: qcom: Add Global Clock controller (GCC) driver for SDM845") Reported-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org> Link: https://lkml.kernel.org/r/20191126153437.11808-1-georgi.djakov@linaro.org Tested-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The PMU registers are at least 0x18 bytes wide. Meson8b already uses a
size of 0x18. The structure of the PMU registers on Meson8 and Meson8b
is similar but not identical.
Meson8 and Meson8b have the following registers in common (starting at
AOBUS + 0xe0):
#define AO_RTI_PWR_A9_CNTL0 0xe0 (0x38 << 2)
#define AO_RTI_PWR_A9_CNTL1 0xe4 (0x39 << 2)
#define AO_RTI_GEN_PWR_SLEEP0 0xe8 (0x3a << 2)
#define AO_RTI_GEN_PWR_ISO0 0x4c (0x3b << 2)
Meson8b additionally has these three registers:
#define AO_RTI_GEN_PWR_ACK0 0xf0 (0x3c << 2)
#define AO_RTI_PWR_A9_MEM_PD0 0xf4 (0x3d << 2)
#define AO_RTI_PWR_A9_MEM_PD1 0xf8 (0x3e << 2)
Thus we can assume that the register size of the PMU IP blocks is
identical on both SoCs (and Meson8 just contains some reserved registers
in that area) because the CEC registers start right after the PMU
(AO_RTI_*) registers at AOBUS + 0x100 (0x40 << 2).
The upcoming power domain driver will need to read and write the
AO_RTI_GEN_PWR_SLEEP0 and AO_RTI_GEN_PWR_ISO0 registers, so the updated
size is needed for that driver to work.
Fixes: 4a5a27116b447d ("ARM: dts: meson8: add support for booting the secondary CPU cores") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Cross compiling the x86 kernel on a non-x86 build machine produces
the following error when CONFIG_UNWINDER_ORC is enabled, regardless
of whether libelf-dev is installed or not.
dpkg-checkbuilddeps: error: Unmet build dependencies: libelf-dev
dpkg-buildpackage: warning: build dependencies/conflicts unsatisfied; aborting
dpkg-buildpackage: warning: (Use -d flag to override.)
Since this is a build time dependency for a build tool, we need to
depend on the native version of libelf-dev so add the appropriate
annotation.
A struct that needs to be aligned to 32 bytes has a size of 28. Increase
the size to 32.
This makes elements of arrays of this struct aligned to 32 as well, and
other structs where members are aligned to 32 mixing
ipu3_uapi_awb_fr_config_s as well as other types.
Fixes: commit dca5ef2aa1e6 ("media: staging/intel-ipu3: remove the unnecessary compiler flags") Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Tested-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When smu version is larger than 0x41e2b, it will load
raven_kicker_rlc.bin.To enable gfxoff for raven_kicker_rlc.bin,it
needs to avoid adev->pm.pp_feature &= ~PP_GFXOFF_MASK when it loads
raven_kicker_rlc.bin.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't
take the conf_mutex to ensure that the card stays in this state while
being reconfigured.
Rework the code to take this lock, and drop a redundant state check in a
helper function.
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix rxrpc_new_incoming_call() to check that we have a suitable service key
available for the combination of service ID and security class of a new
incoming call - and to reject calls for which we don't.
This causes an assertion like the following to appear:
rxrpc: Assertion failed - 6(0x6) == 12(0xc) is false
kernel BUG at net/rxrpc/call_object.c:456!
Where call->state is RXRPC_CALL_SERVER_SECURING (6) rather than
RXRPC_CALL_COMPLETE (12).
Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Standard kernel mutexes cannot be used in any way from interrupt or softirq
context, so the user_mutex which manages access to a call cannot be a mutex
since on a new call the mutex must start off locked and be unlocked within
the softirq handler to prevent userspace interfering with a call we're
setting up.
Commit a0855d24fc22d49cdc25664fb224caee16998683 ("locking/mutex: Complain
upon mutex API misuse in IRQ contexts") causes big warnings to be splashed
in dmesg for each a new call that comes in from the server. Whilst it
*seems* like it should be okay, since the accept path uses trylock, there
are issues with PI boosting and marking the wrong task as the owner.
Fix this by not taking the mutex in the softirq path at all. It's not
obvious that there should be any need for it as the state is set before the
first notification is generated for the new call.
There's also no particular reason why the link-assessing ping should be
triggered inside the mutex. It's not actually transmitted there anyway,
but rather it has to be deferred to a workqueue.
Further, I don't think that there's any particular reason that the socket
notification needs to be done from within rx->incoming_lock, so the amount
of time that lock is held can be shortened too and the ping prepared before
the new call notification is sent.
Fixes: 540b1c48c37a ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Peter Zijlstra (Intel) <peterz@infradead.org>
cc: Ingo Molnar <mingo@redhat.com>
cc: Will Deacon <will@kernel.org>
cc: Davidlohr Bueso <dave@stgolabs.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Move the unlock and the ping transmission for a new incoming call into
rxrpc_new_incoming_call() rather than doing it in the caller. This makes
it clearer to see what's going on.
Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
cc: Ingo Molnar <mingo@redhat.com>
cc: Will Deacon <will@kernel.org>
cc: Davidlohr Bueso <dave@stgolabs.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.
Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The sector size of the block layer is 512 bytes, but integrity interval
size might be different (in case of 4K block size of the media). At the
initiator side the virtual start sector is the one that was originally
submitted by the block layer (512 bytes) for the Reftag usage. The
initiator converts the Reftag to integrity interval units and sends it to
the target. So the target virtual start sector should be calculated at
integrity interval units. prepare_fn() and complete_fn() don't remap
correctly the Reftag when using incorrect units of the virtual start
sector, which leads to the following protection error at the device:
"blk_update_request: protection error, dev sdb, sector 2048 op 0x0:(READ)
flags 0x10000 phys_seg 1 prio class 0"
To fix that, set the seed in integrity interval units.
Link: https://lore.kernel.org/r/1576078562-15240-1-git-send-email-israelr@mellanox.com Signed-off-by: Israel Rukshin <israelr@mellanox.com> Reviewed-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In fsl_lpspi_probe an SPI controller is allocated either via
spi_alloc_slave or spi_alloc_master. In all but one error cases this
controller is put by going to error handling code. This commit fixes the
case when pm_runtime_get_sync fails and it should go to the error
handling path.
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Link: https://lore.kernel.org/r/20190930034602.1467-1-navid.emamdoost@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In DMA mode we have a maximum transfer size, past that the driver
falls back to PIO (see the check at the top of pxa2xx_spi_transfer_one).
Falling back to PIO for big transfers defeats the point of a dma engine,
hence set the max transfer size to inform spi clients that they need
to do something smarter.
This was uncovered by the drm_mipi_dbi spi panel code, which does
large spi transfers, but stopped splitting them after:
If there are more than one valid snod on the sleb->nodes list,
do_kill_orphans will malloc ino more than once without releasing
previous ino's memory. Finally, it will trigger memory leak.
Fixes: ee1438ce5dc4 ("ubifs: Check link count of inodes when...") Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In the implementation of aspeed_video_probe() the allocated memory for
video should be released if either devm_ioremap_resource()
or aspeed_video_init() or aspeed_video_setup_video() fails. Replace
kzalloc() with devm_kzalloc to avoid explicit release for video.
Fixes: d2b4387f3bdf ("media: platform: Add Aspeed Video Engine driver") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Reviewed-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com> Reviewed-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The BIT decoder picture run temporarily locks the bitstream mutex while
the coda device mutex is locked, to refill the bitstream ring buffer.
Consequently, the decoder start command, which locks both mutexes when
flushing the bitstream ring buffer, must lock the coda device mutex
first as well, to avoid an ABBA deadlock.
Fixes: e7fd95849b3c ("media: coda: flush bitstream ring buffer on decoder restart") Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
It is not clear what pixel format is actually configured in hardware on
reset. MEDIA_BUS_FMT_YUYV8_2X8, assumed on device probe since the
driver was intiially submitted, is for sure not the one.
Fix it by explicitly applying a known, driver default frame format just
after initial device reset.
Fixes: 2f6e2404799a ("[media] SoC Camera: add driver for OV6650 sensor") Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If number of CPUs are limited by the kernel commandline parameter nr_cpus
assignment of interrupts accourding to numa rules might not be possibe.
As a fallback use one of the online CPUs as interrupt destination.
Fixes: 69a07a41d908 ("MIPS: SGI-IP27: rework HUB interrupts") Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When changing interrupt affinity remember the possible changed nasid,
otherwise an interrupt deactivate/activate sequence will incorrectly
setup interrupt.
Fixes: e6308b6d35ea ("MIPS: SGI-IP27: abstract chipset irq from bridge") Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Previously, pci_pm_resume_noirq() cleared the PME Status bit in the Root
Status register only if the device had no driver or the driver did not
implement legacy power management. It should clear PME Status regardless
of what sort of power management the driver supports, so do this before
checking for legacy power management.
This affects Root Ports and Root Complex Event Collectors, for which the
usual driver is the PCIe portdrv, which implements new power management, so
this change is just on principle, not to fix any actual defects.
Fixes: a39bd851dccf ("PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver") Link: https://lore.kernel.org/r/20191014230016.240912-4-helgaas@kernel.org Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit e80a91ad302b ("PCI: Add dma_ranges window list") added a
dma_ranges resource list, but failed to correctly free the list when
devm_pci_alloc_host_bridge() is used.
Only the iproc host bridge driver is using the dma_ranges list.
PCI_EXP_RTCTL is used to activate PME interrupt only, so writing into it
should not modify other interrupts' mask. The ISR mask polarity was also
inverted, when PCI_EXP_RTCTL_PMEIE is set PCIE_MSG_PM_PME_MASK mask bit
should actually be cleared.
Aardvark's PCI_EXP_LNKSTA_LT flag in its link status register is not
implemented and does not reflect the actual link training state (the
flag is always set to 0). In order to support link re-training feature
this flag has to be emulated. The Link Training and Status State
Machine (LTSSM) flag in Aardvark LMI config register could be used as
a link training indicator. Indeed if the LTSSM is in L0 or upper state
then link training has completed (see [1]).
Unfortunately because after asking a link retraining it takes a while
for the LTSSM state to become less than 0x10 (due to L0s to recovery
state transition delays), LTSSM can still be in L0 while link training
has not finished yet. So this waits for link to be in recovery or lesser
state before returning after asking for a link retrain.
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, Table 4-14
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space") Tested-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Remi Pommarel <repk@triplefau.lt> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Andrew Murray <andrew.murray@arm.com> Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
sh-pfc e6060000.pin-controller: IRQ index 0 not found
Fix this by using the platform_irq_count() helper instead.
This patch allows PINMUX_IPSR_PHYS() to set bits in GPSR.
When assigning function to pin, GPSR should be set to peripheral
function.
For example when using SCL3, GPSR2 bit7 (PWM1_A pin) should be set to
peripheral function.
In affs_remount if data is provided it is duplicated into new_opts. The
allocated memory for new_opts is only released if parse_options fails.
There's a bit of history behind new_options, originally there was
save/replace options on the VFS layer so the 'data' passed must not
change (thus strdup), this got cleaned up in later patches. But not
completely.
There's no reason to do the strdup in cases where the filesystem does
not need to reuse the 'data' again, because strsep would modify it
directly.
Memory allocated in alloc_clk() for 'struct clk' and
'const char *con_id' while invoking clk_register() is never freed
in clk_unregister(), resulting in kmemleak showing the following
backtrace.
If the server returns a bad or dead session error, the we don't want
to update the session slot number, but just immediately schedule
recovery and allow it to proceed.
We can/should then remove handling in other places
Fixes: 3453d5708b33 ("NFSv4.1: Avoid false retries when RPC calls are interrupted") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The new nfsdcld client tracking operations use sha256 to compute hashes
of the kerberos principals, so make sure CRYPTO_SHA256 is enabled.
Fixes: 6ee95d1c8991 ("nfsd: add support for upcall version 2") Reported-by: Jamie Heilman <jamie@audible.transient.net> Signed-off-by: Scott Mayhew <smayhew@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The geode AES driver is heavily broken because it stores per-request
state in the transform context. So it will crash or produce the wrong
result if used by any of the many places in the kernel that issue
concurrent requests for the same transform object.
This driver is also implemented using the deprecated blkcipher API,
which makes it difficult to fix, and puts it among the drivers
preventing that API from being removed.
Convert this driver to use the skcipher API, and change it to not store
per-request state in the transform context.
Fixes: 9fe757b0cfce ("[PATCH] crypto: Add support for the Geode LX AES hardware") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When algif_skcipher does a partial operation it always process data
that is a multiple of blocksize. However, for algorithms such as
CTR this is wrong because even though it can process any number of
bytes overall, the partial block must come at the very end and not
in the middle.
This is exactly what chunksize is meant to describe so this patch
changes blocksize to chunksize.
Fixes: 8ff590903d5f ("crypto: algif_skcipher - User-space...") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The fix is to copy the qp_init_attr struct that was just created by
rpcrdma_ep_create() instead of using the one from the previous
connection instance.
Fixes: 98ef77d1aaa7 ("xprtrdma: Send Queue size grows after a reconnect") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix attribute name from "jtag_enable", which described twice to
"cpld3_version", which is expected to be instead of second appearance
of "jtag_enable".
Fixes: 2752e34442b5 ("Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces") Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The commit c296d4dc13ae ("asm-generic: fix a compilation warning") changed
asm-generic/cachflush.h to use static inlines instead of macros and as a
result the nds32 build with CONFIG_CPU_CACHE_ALIASING=n fails:
CC init/main.o
In file included from arch/nds32/include/asm/cacheflush.h:43,
from include/linux/highmem.h:12,
from include/linux/pagemap.h:11,
from include/linux/blkdev.h:16,
from include/linux/blk-cgroup.h:23,
from include/linux/writeback.h:14,
from init/main.c:44:
include/asm-generic/cacheflush.h:50:20: error: static declaration of 'flush_icache_range' follows non-static declaration
static inline void flush_icache_range(unsigned long start, unsigned long end)
^~~~~~~~~~~~~~~~~~
In file included from include/linux/highmem.h:12,
from include/linux/pagemap.h:11,
from include/linux/blkdev.h:16,
from include/linux/blk-cgroup.h:23,
from include/linux/writeback.h:14,
from init/main.c:44:
arch/nds32/include/asm/cacheflush.h:11:6: note: previous declaration of 'flush_icache_range' was here
void flush_icache_range(unsigned long start, unsigned long end);
^~~~~~~~~~~~~~~~~~
Surround the inline functions in asm-generic/cacheflush.h by ifdef's so
that architectures could override them and add the required overrides to
nds32.
Fixes: c296d4dc13ae ("asm-generic: fix a compilation warning") Link: https://lore.kernel.org/lkml/201912212139.yptX8CsV%25lkp@intel.com/ Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Greentime Hu <green.hu@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This commit fixes the potential deadlock caused by the console Rx
and Tx processing at the same time. Rx and Tx both take the console
and tmfifo spinlock but in different order which causes potential
deadlock. The fix is to use different tmfifo spinlock for Rx and
Tx since they protect different resources and it's safe to split
the lock.
Below is the reported call trace when copying/pasting large string
in the console.
When the key cached by request_key() and co. is cleaned up on exit(),
the code looks in the wrong task_struct, and so clears the wrong cache.
This leads to anomalies in key refcounting when doing, say, a kernel
build on an afs volume, that then trigger kasan to report a
use-after-free when the key is viewed in /proc/keys.
Fix this by making exit_creds() look in the passed-in task_struct rather
than in current (the task_struct cleanup code is deferred by RCU and
potentially run in another task).
Fixes: 7743c48e54ee ("keys: Cache result of request_key*() temporarily in task_struct") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix afs_lookup() to not clobber the version set on a new dentry by
afs_do_lookup() - especially as it's using the wrong version of the
version (we need to use the one given to us by whatever op the dir
contents correspond to rather than what's in the afs_vnode).
Fixes: 9dd0b82ef530 ("afs: Fix missing dentry data version updating") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
afs_lookup() has a tracepoint to indicate the outcome of
d_splice_alias(), passing it the inode to retrieve the fid from.
However, the function gave up its ref on that inode when it called
d_splice_alias(), which may have failed and dropped the inode.
Fix this by caching the fid.
Fixes: 80548b03991f ("afs: Add more tracepoints") Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Ensure psock dereference on line 792 only occurs if psock is not null.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Convert the bpf_probe_write_user() helper to probe_user_write() such that
writes are not attempted under KERNEL_DS anymore which is buggy as kernel
and user space pointers can have overlapping addresses. Also, given we have
the access_ok() check inside probe_user_write(), the helper doesn't need
to do it twice.
Fixes: 96ae52279594 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/841c461781874c07a0ee404a454c3bc0459eed30.1572649915.git.daniel@iogearbox.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 3d7081822f7f ("uaccess: Add non-pagefault user-space read functions")
missed to add probe write function, therefore factor out a probe_write_common()
helper with most logic of probe_kernel_write() except setting KERNEL_DS, and
add a new probe_user_write() helper so it can be used from BPF side.
Again, on some archs, the user address space and kernel address space can
co-exist and be overlapping, so in such case, setting KERNEL_DS would mean
that the given address is treated as being in kernel address space.
qpc/cqc timer entry size needs one page, but currently they are fixedly
configured to 4096, which is not appropriate in 64K page scenarios. So
they should be modified to PAGE_SIZE.
Fixes: 0e40dc2f70cd ("RDMA/hns: Add timer allocation support for hip08") Link: https://lore.kernel.org/r/1571908917-16220-3-git-send-email-liweihang@hisilicon.com Signed-off-by: Yangyang Li <liyangyang20@huawei.com> Signed-off-by: Weihang Li <liweihang@hisilicon.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A recent clean up attempted to separate Receive handling and RPC
Reply processing, in the name of clean layering.
Unfortunately, we can't do this because the Receive Queue has to be
refilled _after_ the most recent credit update from the responder
is parsed from the transport header, but _before_ we wake up the
next RPC sender. That is right in the middle of
rpcrdma_reply_handler().
Usually this isn't a problem because current responder
implementations don't vary their credit grant. The one exception is
when a connection is established: the grant goes from one to a much
larger number on the first Receive. The requester MUST post enough
Receives right then so that any outstanding requests can be sent
without risking RNR and connection loss.
Fixes: 6ceea36890a0 ("xprtrdma: Refactor Receive accounting") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is because xprt_request_get_cong() is allowing more than one
RPC Call to be transmitted before the first Receive on the new
connection. The first Receive fills the Receive Queue based on the
server's credit grant. Before that Receive, there is only a single
Receive WR posted because the client doesn't know the server's
credit grant.
Solution is to clear rq_cong on all outstanding rpc_rqsts when the
the cwnd is reset. This is because an RPC/RDMA credit is good for
one connection instance only.
Fixes: 75891f502f5f ("SUNRPC: Support for congestion control ... ") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When adding frwr_unmap_async way back when, I re-used the existing
trace_xprtrdma_post_send() trace point to record the return code
of ib_post_send.
Unfortunately there are some cases where re-using that trace point
causes a crash. Instead, construct a trace point specific to posting
Local Invalidate WRs that will always be safe to use in that context,
and will act as a trace log eye-catcher for Local Invalidation.
Fixes: 847568942f93 ("xprtrdma: Remove fr_state") Fixes: d8099feda483 ("xprtrdma: Reduce context switching due ... ") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Bill Baker <bill.baker@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is not the first attempt to fix building random configurations,
unfortunately the attempt in commit a07fc0bb483e ("RDMA/hns: Fix build
error") caused a new problem when CONFIG_INFINIBAND_HNS_HIP06=m and
CONFIG_INFINIBAND_HNS_HIP08=y:
drivers/infiniband/hw/hns/hns_roce_main.o:(.rodata+0xe60): undefined reference to `__this_module'
Revert commits a07fc0bb483e ("RDMA/hns: Fix build error") and a3e2d4c7e766 ("RDMA/hns: remove obsolete Kconfig comment") to get back to
the previous state, then fix the issues described there differently, by
adding more specific dependencies: INFINIBAND_HNS can now only be built-in
if at least one of HNS or HNS3 are built-in, and the individual back-ends
are only available if that code is reachable from the main driver.
Fixes: a07fc0bb483e ("RDMA/hns: Fix build error") Fixes: a3e2d4c7e766 ("RDMA/hns: remove obsolete Kconfig comment") Fixes: dd74282df573 ("RDMA/hns: Initialize the PCI device for hip08 RoCE") Fixes: 08805fdbeb2d ("RDMA/hns: Split hw v1 driver from hns roce driver") Link: https://lore.kernel.org/r/20191007211826.3361202-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The current driver only sets 0x76543210 and 0x67452301 for DALIGN.
This doesn’t work well for TDM split and ex-split mode for all SSIU.
This patch programs the DALIGN registers based on the SSIU number.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: Jiada Wang <jiada_wang@mentor.com> Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com> Fixes: a914e44693d41b ("ASoC: rsnd: more clear rsnd_get_dalign() for DALIGN") Signed-off-by: Nilkanth Ahirrao <anilkanth@jp.adit-jv.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20191121111023.10976-1-erosca@de.adit-jv.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
projects / mirror_ubuntu-eoan-kernel.git / log