* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: unbind all interfaces before rebinding them
USB: serial: digi_acceleport: Eliminate a NULL pointer dereference
usb: fix ehci_hcd build failure when both generic-OF and xilinx is selected
USB: cdc-acm: fix resource reclaim in error path of acm_probe
USB: ftdi_sio: fix DTR/RTS line modes
USB: s3c-hsotg: Ensure FIFOs are fully flushed after layout
USB: s3c-hsotg: SoftDisconnect minimum 3ms
USB: s3c-hsotg: Ensure TX FIFO addresses setup when initialising FIFOs
USB: s3c_hsotg: define USB_GADGET_DUALSPEED in Kconfig
USB: s3c: Enable soft disconnect during initialization
USB: xhci: Print NEC firmware version.
USB: xhci: Wait for host to start running.
USB: xhci: Wait for controller to be ready after reset.
USB: isp1362: fix inw warning on Blackfin systems
USB: mos7840: fix null-pointer dereference
Cory Maccarrone [Fri, 4 Jun 2010 21:15:07 +0000 (14:15 -0700)]
omap: remove BUG_ON for disabled interrupts
Remove a BUG_ON for when interrupts are disabled during an MMC request.
During boot, interrupts can be disabled when a request is made, causing
this bug to be triggered. In reality, there's no reason this should halt
the kernel, as the driver has proved reliable in spite of disabled
interrupts, and additionally, there's nothing in this code that would
require interrupts to be enabled.
The only setup I've managed to make it trigger on is on the HTC Herald
during bootup when the driver is built into the kernel (mostly because
that's all I have). I believe it's related to the fact that on bootup I
get many timeout errors on "CMD5" while initializing the card. Each CMD5
timeout triggers that bug (I changed it to a WARN_ON to get it to boot in)
due to the fact that part of the timeout code involves sending the request
again. With interrupts turned off, that BUG would be triggered.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
page allocator: smarter retry of costly-order allocations
Original intention was "return success if the system have shrinkable zones
though priority==0 reclaim was failure". But the above patch changed to
"return nr_reclaimed if .....". Oh, That forgot nr_reclaimed may be 0 if
priority==0 reclaim failure.
And Johannes's patch 0aeb2339e54e ("vmscan: remove all_unreclaimable scan
control") made it more corrupt. Originally, priority==0 reclaim failure
on memcg return 0, but this patch changed to return 1. It totally
confused memcg.
Akinobu Mita [Fri, 4 Jun 2010 21:15:04 +0000 (14:15 -0700)]
kernel/: fix BUG_ON checks for cpu notifier callbacks direct call
The commit 80b5184cc537718122e036afe7e62d202b70d077 ("kernel/: convert cpu
notifier to return encapsulate errno value") changed the return value of
cpu notifier callbacks.
Those callbacks don't return NOTIFY_BAD on failures anymore. But there
are a few callbacks which are called directly at init time and checking
the return value.
I forgot to change BUG_ON checking by the direct callers in the commit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Child groups should have a greater depth than their parents. Prior to
this change, the parent would incorrectly report zero memory usage for
child cgroups when use_hierarchy is enabled.
test script:
mount -t cgroup none /cgroups -o memory
cd /cgroups
mkdir cg1
Using fae9c79, a recent patch that changed alloc_css_id() depth computation,
the parent incorrectly reports zero usage:
root@ubuntu:~# ./test
1+0 records in
1+0 records out 1048576 bytes (1.0 MB) copied, 0.0151844 s, 69.1 MB/s
With this patch, the parent correctly includes child usage:
root@ubuntu:~# ./test
1+0 records in
1+0 records out 1048576 bytes (1.0 MB) copied, 0.0136827 s, 76.6 MB/s
Commit f601441916d1e19291d0b4f044b4a7551e2924d0 ("imxfb: add support for
i.MX25:) has inserted the symbol HAVE_FB_IMX, which does not depend on FB
after the menuconfig FB. This breaks the menu, presenting most of the
drivers outside of it, when using menuconfig.
Moving the symbol to the start of the file, just like HAVE_FB_ATMEL, fixes
the problem without breaking it for iMX25 configurations (tested with
ARCH=arm, no build).
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Baruch Siach <baruch@tkos.co.il> Cc: "David S. Miller" <davem@davemloft.net> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/um: fix kunmap_atomic() call in skas/uaccess.c
kunmap_atomic() takes a pointer to within the page, not the struct page.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Fri, 4 Jun 2010 21:14:58 +0000 (14:14 -0700)]
sys_personality: change sys_personality() to accept "unsigned int" instead of u_long
task_struct->pesonality is "unsigned int", but sys_personality() paths use
"unsigned long pesonality". This means that every assignment or
comparison is not right. In particular, if this argument does not fit
into "unsigned int" __set_personality() changes the caller's personality
and then sys_personality() returns -EINVAL.
Turn this argument into "unsigned int" and avoid overflows. Obviously,
this is the user-visible change, we just ignore the upper bits. But this
can't break the sane application.
There is another thing which can confuse the poorly written applications.
User-space thinks that this syscall returns int, not long. This means
that the returned value can be negative and look like the error code. But
note that libc won't be confused and thus errno won't be set, and with
this patch the user-space can never get -1 unless sys_personality() really
fails. And, most importantly, the negative RET != -1 is only possible if
that app previously called personality(RET).
Although the fix provided is correct, it's been suggested to avoid the
underlying race in the same way as it is currently done in filesystems
like NFS, for maintainability.
A following patch "fb_defio: redo fix for non-dirty ptes" will provide
such an alternate fix.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Cc: Jaya Kumar <jayakumar.lkml@gmail.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Fri, 4 Jun 2010 21:14:55 +0000 (14:14 -0700)]
flat: fix unmap len in load error path
The data chunk is mmaped with 'len' which remains unchanged, so use that
when unmapping in the error path rather than trying to recalculate (and
incorrectly so) the value used originally.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: David McCullough <davidm@snapgear.com> Acked-by: Greg Ungerer <gerg@uclinux.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Michal Simek <monstr@monstr.eu> Cc: Hirokazu Takata <takata@linux-m32r.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Fri, 4 Jun 2010 21:14:53 +0000 (14:14 -0700)]
fs/binfmt_flat.c: split the stack & data alignments
The stack and data have different alignment requirements, so don't force
them to wear the same shoe. Increase the data alignment to match that
which the elf2flt linker script has always been using: 0x20 bytes. Not
only does this bring the kernel loader in line with the toolchain, but it
also fixes a swath of gcc tests which try to force larger alignment values
but randomly fail when the FLAT loader fails to deliver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: David Woodhouse <David.Woodhouse@intel.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Acked-by: David McCullough <davidm@snapgear.com> Acked-by: Greg Ungerer <gerg@uclinux.org> Cc: Paul Mundt <lethal@linux-sh.org> Tested-by: Michal Simek <monstr@monstr.eu> Cc: Hirokazu Takata <takata@linux-m32r.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Jie Zhang <jie@codesourcery.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dmitry Torokhov [Fri, 4 Jun 2010 21:14:52 +0000 (14:14 -0700)]
vmware balloon: clamp number of collected non-balloonable pages
Limit number of accumulated non-balloonable pages during inflation cycle,
otherwise there is a chance we will be spinning and growing the list
forever. This happens during torture tests when balloon target changes
while we are in the middle of inflation cycle and monitor starts refusing
to lock pages (since they are not needed anymore).
Nick Piggin [Fri, 4 Jun 2010 21:14:51 +0000 (14:14 -0700)]
xtensa: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: David Rientjes <rientjes@google.com> Cc: Chris Zankel <chris@zankel.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Fri, 4 Jun 2010 21:14:51 +0000 (14:14 -0700)]
mn10300: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: David Rientjes <rientjes@google.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Fri, 4 Jun 2010 21:14:49 +0000 (14:14 -0700)]
m32r: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: David Rientjes <rientjes@google.com> Cc: Hirokazu Takata <takata@linux-m32r.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Fri, 4 Jun 2010 21:14:49 +0000 (14:14 -0700)]
frv: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: David Howells <dhowells@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A call to access_ok is missing a compat_ptr conversion. Introduced with b83733639a494d5f42fa00a2506563fbd2d3015d "compat: factor out
compat_rw_copy_check_uvector from compat_do_readv_writev"
fs/compat.c: In function 'compat_rw_copy_check_uvector':
fs/compat.c:629: warning: passing argument 1 of '__access_ok' makes pointer from integer without a cast
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Stern [Fri, 4 Jun 2010 18:02:42 +0000 (14:02 -0400)]
USB: unbind all interfaces before rebinding them
This patch (as1387) fixes a bug introduced during the changeover to
the runtime PM framework. When a driver doesn't support resume or
reset-resume, and consequently its interfaces need to be unbound and
rebound, we have to unbind all the interfaces before trying to rebind
any of them. Otherwise the driver's probe method for one interface
could try to claim a different interface and fail, because that other
interface hasn't been unbound yet.
This fixes Bugzilla #15788. The symptom is that some USB sound cards
don't work after hibernation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: François Valenduc <francois.valenduc@tvcablenet.be> Cc: stable <stable@kernel.org> [.34] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Grant Likely [Wed, 2 Jun 2010 19:53:17 +0000 (13:53 -0600)]
usb: fix ehci_hcd build failure when both generic-OF and xilinx is selected
This patch fixes the driver to allow both CONFIG_USB_EHCI_HCD_PPC_OF and
CONFIG_USB_ECHI_HCD_XILINX to be selected.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> CC: John Linn <john.linn@xilinx.com> CC: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Axel Lin [Mon, 31 May 2010 00:04:47 +0000 (08:04 +0800)]
USB: cdc-acm: fix resource reclaim in error path of acm_probe
This patch fixes resource reclaim in error path of acm_probe:
1. In the case of "out of memory (read urbs usb_alloc_urb)\n")", there
is no need to call acm_read_buffers_free(acm) here. Fix it by goto
alloc_fail6 instead of alloc_fail7.
2. In the case of "out of memory (write urbs usb_alloc_urb)",
usb_alloc_urb may fail in any iteration of the for loop. Current
implementation does not properly free allocated snd->urb. Fix it by
goto alloc_fail8 instead of alloc_fail7.
3. In the case of device_create_file(&intf->dev,&dev_attr_iCountryCodeRelDate)
fail, acm->country_codes is kfreed. As a result, device_remove_file
for dev_attr_wCountryCodes will not be executed in acm_disconnect.
Fix it by calling device_remove_file for dev_attr_wCountryCodes
before goto skip_countries.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Oliver Neukum <oneukum@suse.de> Cc: stable <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Mack [Thu, 3 Jun 2010 11:55:02 +0000 (13:55 +0200)]
USB: ftdi_sio: fix DTR/RTS line modes
Call set_mctrl() and clear_mctrl() according to the flow control mode
selected. This makes serial communication for FT232 connected devices
work when CRTSCTS is not set.
This fixes a regression introduced by 4175f3e31 ("tty_port: If we are
opened non blocking we still need to raise the carrier"). This patch
calls the low-level driver's dtr_rts() function which consequently sets
TIOCM_DTR | TIOCM_RTS. A later call to set_termios() without CRTSCTS in
cflags, however, does not reset these bits, and so data is not actually
sent out on the serial wire.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Johan Hovold <jhovold@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ben Dooks [Tue, 25 May 2010 04:36:51 +0000 (05:36 +0100)]
USB: s3c-hsotg: SoftDisconnect minimum 3ms
The shortest period SoftDisconnect can be asserted for is 3 milliseconds
according to the V210 datasheet, so ensure that we add an msleep() to
the registration code to enforce this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ben Dooks [Tue, 25 May 2010 04:36:50 +0000 (05:36 +0100)]
USB: s3c-hsotg: Ensure TX FIFO addresses setup when initialising FIFOs
Some versions of the S3C HS OtG block startup with overlapping TX FIFO
information, so change the fifo_init code to ensure that known values
are set into the FIFO registers at initialisation/reset time.
This also ensures that the FIFO RAM pointers are in a known state
before use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: s3c_hsotg: define USB_GADGET_DUALSPEED in Kconfig
The s3c_hsotg driver sets usb_gadget->is_dualspeed to 1, yet it doesn't define
USB_GADGET_DUALSPEED in Kconfig. This triggers a NULL pointer dereference in
the composite driver (which is fixed in another patch).
Thomas Abraham [Mon, 24 May 2010 08:48:56 +0000 (17:48 +0900)]
USB: s3c: Enable soft disconnect during initialization
Enable soft disconnect bit the OTG core during initialization. Without this,
the host sees that a gadget is connected and tries to enumerate. The
soft disconnect should be enabled until the USB gadget driver is
registered with this otg driver.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Mon, 24 May 2010 20:25:28 +0000 (13:25 -0700)]
USB: xhci: Print NEC firmware version.
The NEC xHCI host controller firmware version can be found by putting a
vendor-specific command on the command ring and extracting the BCD
encoded-version out of the vendor-specific event TRB.
The firmware version debug line in dmesg will look like:
xhci_hcd 0000:05:00.0: NEC firmware version 30.21
(NEC merged with Renesas Technologies and became Renesas Electronics on
April 1, 2010. I have their OK to merge this vendor-specific code.)
Sarah Sharp [Mon, 24 May 2010 20:25:21 +0000 (13:25 -0700)]
USB: xhci: Wait for host to start running.
When the run bit is set in the xHCI command register, it may take a few
microseconds for the host to start running. We cannot ring any doorbells
until the host is actually running, so wait until the status register says
the host is running.
Sarah Sharp [Mon, 24 May 2010 20:25:15 +0000 (13:25 -0700)]
USB: xhci: Wait for controller to be ready after reset.
After software resets an xHCI host controller, it must wait for the
"Controller Not Ready" (CNR) bit in the status register to be cleared.
Software is not supposed to ring any doorbells or write to any registers
except the status register until this bit is cleared.
Linus Torvalds [Fri, 4 Jun 2010 20:04:39 +0000 (13:04 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Eliminate us to pm ticks conversion in common path
ACPI: Fix the incorrect calculation about C-state idle time
ACPI: update feature-removal.txt to reflect deleted acpi=ht option
ACPI / EC / PM: Fix names of functions that block/unblock EC transactions
ACPI / EC / PM: Fix race between EC transactions and system suspend
ACPI: Eliminate us to pm ticks conversion in common path
acpi_enter_[simple|bm] routines does us to pm tick conversion on every
idle wakeup and the value is only used in /proc/acpi display. We can
store the time in us and convert it into pm ticks before printing instead and
avoid the conversion in the common path.
Signed-off-by: Venkatesh Pallipadi <venki@google.com> Signed-off-by: Len Brown <len.brown@intel.com>
Zhao Yakui [Wed, 2 Jun 2010 03:04:09 +0000 (11:04 +0800)]
ACPI: Fix the incorrect calculation about C-state idle time
The C-state idle time is not calculated correctly, which will return the wrong
residency time in C-state. It will have the following effects:
1. The system can't choose the deeper C-state when it is idle next time.
Of course the system power is increased. E.g. On one server machine about 40W
idle power is increased.
2. The powertop shows that it will stay in C0 running state about 95% time
although the system is idle at most time.
Linus Torvalds [Fri, 4 Jun 2010 16:48:03 +0000 (09:48 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda-intel - fix wallclk variable update and condition
ALSA: asihpi - Fix uninitialized variable
ALSA: hda: Use LPIB for ASUS M2V
usb/gadget: Replace the old USB audio FU definitions in f_audio.c
ASoC: MX31ads sound support should depend on MACH_MX31ADS_WM1133_EV1
ASoC: Add missing Kconfig entry for Phytec boards
ALSA: usb-audio: export UAC2 clock selectors as mixer controls
ALSA: usb-audio: clean up find_audio_control_unit()
ALSA: usb-audio: add UAC2 sepecific Feature Unit controls
ALSA: usb-audio: unify constants from specification
ALSA: usb-audio: parse clock topology of UAC2 devices
ALSA: usb-audio: fix selector unit string index accessor
include/linux/usb/audio-v2.h: add more UAC2 details
ALSA: usb-audio: support partially write-protected UAC2 controls
ALSA: usb-audio: UAC2: clean up parsing of bmaControls
ALSA: hda: Use LPIB for another mainboard
ALSA: hda: Use mb31 quirk for an iMac model
ALSA: hda: Use LPIB for an ASUS device
Linus Torvalds [Thu, 3 Jun 2010 22:48:15 +0000 (15:48 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement on-demand HPA unlocking
libata: use the enlarged capacity after late HPA unlock
SCSI: implement sd_unlock_native_capacity()
libata-sff: trivial corrections to Kconfig help text
sata_nv: don't diddle with nIEN on mcp55
sata_via: magic vt6421 fix for transmission problems w/ WD drives
Linus Torvalds [Thu, 3 Jun 2010 22:47:51 +0000 (15:47 -0700)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched, trace: Fix sched_switch() prev_state argument
sched: Fix wake_affine() vs RT tasks
sched: Make sure timers have migrated before killing the migration_thread
Linus Torvalds [Thu, 3 Jun 2010 22:47:22 +0000 (15:47 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, smpboot: Fix cores per node printing on boot
x86/amd-iommu: Fall back to GART if initialization fails
x86/amd-iommu: Fix crash when request_mem_region fails
x86/mm: Remove unused DBG() macro
arch/x86/kernel: Add missing spin_unlock
Linus Torvalds [Thu, 3 Jun 2010 22:46:37 +0000 (15:46 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/macio: Fix probing of macio devices by using the right of match table
agp/uninorth: Fix oops caused by flushing too much
powerpc/pasemi: Update MAINTAINERS file
powerpc/cell: Fix integer constant warning
powerpc/kprobes: Remove resume_execution() in kprobes
powerpc/macio: Don't dereference pointer before null check
Linus Torvalds [Thu, 3 Jun 2010 22:46:09 +0000 (15:46 -0700)]
Merge branch 'for-linus/bugfixes' of git://xenbits.xensource.com/people/ianc/linux-2.6
* 'for-linus/bugfixes' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: avoid allocation causing potential swap activity on the resume path
xen: ensure timer tick is resumed even on CPU driving the resume
Linus Torvalds [Thu, 3 Jun 2010 22:45:26 +0000 (15:45 -0700)]
Merge branch 'perf-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix crash in swevents
perf buildid-list: Fix --with-hits event processing
perf scripts python: Give field dict to unhandled callback
perf hist: fix objdump output parsing
perf-record: Check correct pid when forking
perf: Do the comm inheritance per thread in event__process_task
perf: Use event__process_task from perf sched
perf: Process comm events by tid
blktrace: Fix new kernel-doc warnings
perf_events: Fix unincremented buffer base on partial copy
perf_events: Fix event scheduling issues introduced by transactional API
perf_events, trace: Fix perf_trace_destroy(), mutex went missing
perf_events, trace: Fix probe unregister race
perf_events: Fix races in group composition
perf_events: Fix races and clean up perf_event and perf_mmap_data interaction
Linus Torvalds [Thu, 3 Jun 2010 22:45:03 +0000 (15:45 -0700)]
Merge branch 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus
* 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: console: Fix crash when port is unplugged and blocked for write
virtio: console: Fix crash when hot-unplugging a port and read is blocked
virtio-blk: fix minimum number of S/G elements
Peter Zijlstra [Thu, 3 Jun 2010 09:21:20 +0000 (11:21 +0200)]
perf: Fix crash in swevents
Frederic reported that because swevents handling doesn't disable IRQs
anymore, we can get a recursion of perf_adjust_period(), once from
overflow handling and once from the tick.
If both call ->disable, we get a double hlist_del_rcu() and trigger
a LIST_POISON2 dereference.
Since we don't actually need to stop/start a swevent to re-programm
the hardware (lack of hardware to program), simply nop out these
callbacks for the swevent pmu.
Linus Torvalds [Thu, 3 Jun 2010 14:19:45 +0000 (07:19 -0700)]
Merge branch 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (41 commits)
drm/radeon/kms: make sure display hw is disabled when suspending
drm/vmwgfx: Allow userspace to change default layout. Bump minor.
drm/vmwgfx: Fix framebuffer modesetting
drm/vmwgfx: Fix vga save / restore with display topology.
vgaarb: use MIT license
vgaarb: convert pr_devel() to pr_debug()
drm: fix typos in Linux DRM Developer's Guide
drm/radeon/kms/pm: voltage fixes
drm/radeon/kms/pm: radeon_set_power_state fixes
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
drm/radeon/kms/pm: enable SetVoltage on r7xx/evergreen
drm/radeon/kms/pm: add support for SetVoltage cmd table (V2)
drm/radeon/kms/evergreen: add initial CS parser
drm/kms: disable/enable poll around switcheroo on/off
drm/nouveau: fixup confusion over which handle the DSM is hanging off.
drm/nouveau: attempt to get bios from ACPI v3
drm/nv50: cast IGP memory location to u64 before shifting
drm/ttm: Fix ttm_page_alloc.c
drm/ttm: Fix cached TTM page allocation.
drm/vmwgfx: Remove some leftover debug messages.
...
Amit Shah [Thu, 27 May 2010 07:54:40 +0000 (13:24 +0530)]
virtio: console: Fix crash when port is unplugged and blocked for write
When a program that has a virtio port opened and blocked for a write
operation, a port hot-unplug event will later led to a crash when
SIGTERM was sent to the program. Fix that.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Amit Shah [Thu, 27 May 2010 07:54:39 +0000 (13:24 +0530)]
virtio: console: Fix crash when hot-unplugging a port and read is blocked
When removing a port we don't check if a program was blocked for read.
This leads to a crash when SIGTERM is sent to the program after
hot-unplugging the port.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We need at least one S/G element to operate properly, as does the block
layer which increments it to one anyway. We hit this due to a qemu
bug which advertises a sg_elements of 0 under some circumstances.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (tweaked logic)
Wolfram Sang [Thu, 3 Jun 2010 09:33:58 +0000 (11:33 +0200)]
i2c: Remove all i2c_set_clientdata(client, NULL) in drivers
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit e4a7b9b04de15f6b63da5ccdd373ffa3057a3681 to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Acked-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Thu, 3 Jun 2010 09:33:52 +0000 (11:33 +0200)]
i2c: Check for address validity on client registration
Do basic address validity checks when a client is being registered. We
already had checks in place for devices which are being detected, but
not for devices which are simply instantiated.
This is a very basic check. We don't want to do strict checking here
because some devices are known to infringe the I2C address constraints
(e.g. IR receivers at 7-bit address 0x7a while this value is
supposedly reserved for 10-bit addresses.) So we assume the caller
knows what it is doing.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Matthieu Castet <castet.matthieu@free.fr>
Ian Campbell [Tue, 25 May 2010 09:45:35 +0000 (10:45 +0100)]
xen: avoid allocation causing potential swap activity on the resume path
Since the device we are resuming could be the device containing the
swap device we should ensure that the allocation cannot cause
IO.
On resume, this path is triggered when the running system tries to
continue using its devices. If it cannot then the resume will fail;
to try to avoid this we let it dip into the emergency pools.
Ian Campbell [Wed, 19 May 2010 15:19:25 +0000 (16:19 +0100)]
xen: ensure timer tick is resumed even on CPU driving the resume
The core suspend/resume code is run from stop_machine on CPU0 but
parts of the suspend/resume machinery (including xen_arch_resume) are
run on whichever CPU happened to schedule the xenwatch kernel thread.
As part of the non-core resume code xen_arch_resume is called in order
to restart the timer tick on non-boot processors. The boot processor
itself is taken care of by core timekeeping code.
xen_arch_resume uses smp_call_function which does not call the given
function on the current processor. This means that we can end up with
one CPU not receiving timer ticks if the xenwatch thread happened to
be scheduled on CPU > 0.
Use on_each_cpu instead of smp_call_function to ensure the timer tick
is resumed everywhere.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Stable Kernel <stable@kernel.org> # .32.x
drm/vmwgfx: Allow userspace to change default layout. Bump minor.
The host may change the layout and, since the change is
communicated to the master, the master needs a way to
communicate the change to the kernel driver.
The minor version number is bumped to advertize the
availability of this feature.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Must set SVGA_NUM_REG_GUEST_DISPLAY before setting up the display information.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 27 May 2010 21:01:41 +0000 (17:01 -0400)]
drm/radeon/kms/pm: radeon_set_power_state fixes
- wait for vbl for both profile and dynpm
- unify profile and dynpm code paths more
- call pm_misc before of after clocks to make
sure voltage is changed in the proper order.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 27 May 2010 21:01:40 +0000 (17:01 -0400)]
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
The default power state does not always match the default clocks and voltage
for a particular card. The information in the firmware info table is correct
and should be used in preference to the info the default power state.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes build errors caused by the:
- OF device_node pointer being moved into struct device
- typo in match_table field in the struct device_driver
(which shoud be of_match_table)
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Wed, 2 Jun 2010 20:06:09 +0000 (14:06 -0600)]
of/rtc: rtc-mpc5121.c: Fix build failures
Fixes build errors caused by the:
- OF device_node pointer being moved into struct device
- removal of the match_table field from struct of_platform_driver
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> CC: Paul Gortmaker <p_gortmaker@yahoo.com> CC: Alessandro Zummo <a.zummo@towertech.it> CC: Wolfgang Denk <wd@denx.de> CC: Tejun Heo <tj@kernel.org> CC: Anatolij Gustschin <agust@denx.de> CC: rtc-linux@googlegroups.com CC: devicetree-discuss@lists.ozlabs.org
Fixes build errors caused by the:
- OF device_node pointer being moved into struct device
- removal of the match_table field from struct of_platform_driver
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build errors caused by the:
- OF device_node pointer being moved into struct device
- removal of the match_table field from struct of_platform_driver
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build errors caused by the:
- OF device_node pointer being moved into struct device
- removal of the match_table field from struct of_platform_driver
Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 61c7a080a5a061c976988fd4b844dfb468dda255 ( of: Always use
'struct device.of_node' to get device node pointer.) missed
drivers/watchdog/mpc8xxx_wdt.c. This patch fixes it
Signed-off-by: Michael Guntsche <mike@it-loops.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Wed, 2 Jun 2010 19:35:02 +0000 (13:35 -0600)]
of/usb: fix build error due to of_node pointer move
Fix driver to use new location of of_node pointer (introduced by commit
use new location of of_node pointer (introduced by commit 61c7a080a5a061c976988fd4b844dfb468dda255; of: Always use 'struct
device.of_node' to get device node pointer)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Reported-by: John Linn <john.linn@xilinx.com> CC: Greg Kroah-Hartman <gregkh@suse.de> CC: Alan Stern <stern@rowland.harvard.edu> CC: linux-usb@vger.kernel.org CC: devicetree-discuss@lists.ozlabs.org
Tejun Heo [Sat, 15 May 2010 18:09:34 +0000 (20:09 +0200)]
libata: implement on-demand HPA unlocking
Implement ata_scsi_unlock_native_capacity() which will be called
through SCSI layer when block layer notices that partitions on a
device extend beyond the end of the device. It requests EH to unlock
HPA, waits for completion and returns the current device capacity.
This allows libata to unlock HPA on demand instead of having to decide
whether to unlock upfront. Unlocking on demand is safer than
unlocking by upfront because some BIOSes write private data to the
area beyond HPA limit. This was suggested by Ben Hutchings.
Signed-off-by: Tejun Heo <tj@kernel.org> Suggested-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
projects / mirror_ubuntu-eoan-kernel.git / log