SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.
Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.
Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.
Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Fix the pointer to struct scp_subdomian not being moved forward
when each sub-domain is expected to be iteratively added through
pm_genpd_add_subdomain call.
Cc: stable@vger.kernel.org Fixes: 53fddb1a66dd ("soc: mediatek: reduce code duplication of scpsys_probe across all SoCs") Reported-by: Weiyi Lu <weiyi.lu@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Follow the change of return type u32 of hid_report_len,
fix all the types of variables those get the return value of
hid_report_len to u32, and all other code already uses u32.
The OPAL NVRAM driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, and various lockup errors to trigger (again, BMC reboot
can cause it).
Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.
Fixes: 628daa8d5abf ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Depends-on: 34dd25de9fe3 ("powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops") Cc: stable@vger.kernel.org # v3.2+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is the start of an effort to tidy up and standardise all the
delays. Existing loops have a range of delay/sleep periods from 1ms
to 20ms, and some have no delay. They all loop forever except rtc,
which times out after 10 retries, and that uses 10ms delays. So use
10ms as our standard delay. The OPAL maintainer agrees 10ms is a
reasonable starting point.
The idea is to use the same recipe everywhere, once this is proven to
work then it will be documented as an OPAL API standard. Then both
firmware and OS can agree, and if a particular call needs something
else, then that can be documented with reasoning.
This is not the end-all of this effort, it's just a relatively easy
change that fixes some existing high latency delays. There should be
provision for standardising timeouts and/or interruptible loops where
possible, so non-fatal firmware errors don't cause hangs.
kexec_file_load() on powerpc doesn't support kdump kernels yet, so it
returns -ENOTSUPP in that case.
I've recently learned that this errno is internal to the kernel and
isn't supposed to be exposed to userspace. Therefore, change to
-EOPNOTSUPP which is defined in an uapi header.
This does indeed make kexec-tools happier. Before the patch, on
ppc64le:
This is showing up since OPTPROBES is now enabled with CONFIG_PREEMPT.
trampoline_probe_handler() considers itself to be a special kprobe
handler for kretprobes. In doing so, it expects to be called from
kprobe_handler() on a trap, and re-enables preemption before returning a
non-zero return value so as to suppress any subsequent processing of the
trap by the kprobe_handler().
However, with optprobes, we don't deal with special handlers (we ignore
the return code) and just try to re-enable preemption causing the above
trace.
To address this, modify trampoline_probe_handler() to not be special.
The only additional processing done in kprobe_handler() is to emulate
the instruction (in this case, a 'nop'). We adjust the value of
regs->nip for the purpose and delegate the job of re-enabling
preemption and resetting current kprobe to the probe handlers
(kprobe_handler() or optimized_callback()).
Fixes: 8a2d71a3f273 ("powerpc/kprobes: Disable preemption before invoking probe handler for optprobes") Cc: stable@vger.kernel.org # v4.15+ Reported-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
asm/barrier.h is not always included after asm/synch.h, which meant
it was missing __SUBARCH_HAS_LWSYNC, so in some files smp_wmb() would
be eieio when it should be lwsync. kernel/time/hrtimer.c is one case.
__SUBARCH_HAS_LWSYNC is only used in one place, so just fold it in
to where it's used. Previously with my small simulator config, 377
instances of eieio in the tree. After this patch there are 55.
On POWER9, since commit cc3d2940133d ("powerpc/64: Enable use of radix
MMU under hypervisor on POWER9", 2017-01-30), we set both the radix and
HPT bits in the client-architecture-support (CAS) vector, which tells
the hypervisor that we can do either radix or HPT. According to PAPR,
if we use this combination we are promising to do a H_REGISTER_PROC_TBL
hcall later on to let the hypervisor know whether we are doing radix
or HPT. We currently do this call if we are doing radix but not if
we are doing HPT. If the hypervisor is able to support both radix
and HPT guests, it would be entitled to defer allocation of the HPT
until the H_REGISTER_PROC_TBL call, and to fail any attempts to create
HPTEs until the H_REGISTER_PROC_TBL call. Thus we need to do a
H_REGISTER_PROC_TBL call when we are doing HPT; otherwise we may
crash at boot time.
This adds the code to call H_REGISTER_PROC_TBL in this case, before
we attempt to create any HPT entries using H_ENTER.
Fixes: cc3d2940133d ("powerpc/64: Enable use of radix MMU under hypervisor on POWER9") Cc: stable@vger.kernel.org # v4.11+ Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Presently the dt_cpu_ftrs restore_cpu will only add bits to the LPCR
for secondaries, but some bits must be removed (e.g., UPRT for HPT).
Not clearing these bits on secondaries causes checkstops when booting
with disable_radix.
restore_cpu can not just set LPCR, because it is also called by the
idle wakeup code which relies on opal_slw_set_reg to restore the value
of LPCR, at least on P8 which does not save LPCR to stack in the idle
code.
Fix this by including a mask of bits to clear from LPCR as well, which
is used by restore_cpu.
This is a little messy now, but it's a minimal fix that can be
backported. Longer term, the idle SPR save/restore code can be
reworked to completely avoid calls to restore_cpu, then restore_cpu
would be able to unconditionally set LPCR to match boot processor
environment.
Fixes: 5a61ef74f269f ("powerpc/64s: Support new device tree binding for discovering CPU features") Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
shash and sdesc and always allocated and freed together.
* abstract this in new functions cifs_alloc_hash() and cifs_free_hash().
* make smb2/3 crypto allocation independent from each other.
Signed-off-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On some systems, the BIOS expects certain SMBus register values to
match the hardware defaults. Restore these configuration registers at
shutdown time to avoid confusing the BIOS. This avoids hard-locking
such systems upon reboot.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Tested-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Saving the original value of register SMBSLVCMD in
i801_enable_host_notify() doesn't work, because this function is
called not only at probe time but also at resume time. Do it in
i801_probe() instead, so that the saved value is not overwritten at
resume time.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: 22e94bd6779e ("i2c: i801: store and restore the SLVCMD register at load and unload") Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Tested-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@vger.kernel.org # v4.10+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We can not use the standard sg_set_buf() fucntion since when
CONFIG_DEBUG_SG=y this adds a check that will BUG_ON for cifs.ko
when we pass it an object from the stack.
Create a new wrapper smb2_sg_set_buf() which avoids doing that particular check
and use it for smb3 encryption instead.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:
spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
free_ep_req(hidg->in_ep, hidg->req);
goto try_again;
}
[...]
status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
[...]
=> usb_gadget_giveback_request
=>
f_hidg_req_complete
=>
spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire
Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.
It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.
USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective
suspend and resume, they do not support global suspend/resume where the
hub downstream facing ports states are not affected.
When system enters hibernation it first enters freeze process where only
the root hub enters suspend, usb_port_suspend() is not called for other
devices, and suspend status flags are not set for them. Other devices are
expected to suspend globally. Some external USB3 hubs will suspend the
downstream facing port at global suspend. These devices won't be resumed
at thaw as the suspend status flag is not set.
A USB3 removable hard disk connected through a USB3 hub that won't resume
at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71”
error, and needs a 60 seconds timeout which causing system hang for 60s
before the USB host reset the port for the USB3 removable hard disk to
recover.
Fix this by always calling usb_port_suspend() during freeze for USB3
devices.
It looks like there is a possibility of a double-free vulnerability on an
error path of the f_midi_set_alt function in the f_midi driver. If the
path is feasible then free_ep_req gets called twice:
req->complete = f_midi_complete;
err = usb_ep_queue(midi->out_ep, req, GFP_ATOMIC);
=> ...
usb_gadget_giveback_request
=>
f_midi_complete (CALLBACK)
(inside f_midi_complete, for various cases of status)
free_ep_req(ep, req); // first kfree
if (err) {
ERROR(midi, "%s: couldn't enqueue request: %d\n",
midi->out_ep->name, err);
free_ep_req(midi->out_ep, req); // second kfree
return err;
}
The double-free possibility was introduced with commit ad0d1a058eac
("usb: gadget: f_midi: fix leak on failed to enqueue out requests").
Found by MOXCAFE tool.
Signed-off-by: Tuba Yavuz <tuba@ece.ufl.edu> Fixes: ad0d1a058eac ("usb: gadget: f_midi: fix leak on failed to enqueue out requests") Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Mike Lothian reported that plugging in a USB-C device does not work
properly in his Dell Alienware system. This system has an Intel Alpine
Ridge Thunderbolt controller providing USB-C functionality. In these
systems the USB controller (xHCI) is hotplugged whenever a device is
connected to the port using ACPI-based hotplug.
The ACPI description of the root port in question is as follows:
Device (RP01)
{
Name (_ADR, 0x001C0000)
Device (PXSX)
{
Name (_ADR, 0x02)
Method (_RMV, 0, NotSerialized)
{
// ...
}
}
Here _ADR 0x02 means device 0, function 2 on the bus under root port (RP01)
but that seems to be incorrect because device 0 is the upstream port of the
Alpine Ridge PCIe switch and it has no functions other than 0 (the bridge
itself). When we get ACPI Notify() to the root port resulting from
connecting a USB-C device, Linux tries to read PCI_VENDOR_ID from device 0,
function 2 which of course always returns 0xffffffff because there is no
such function and we never find the device.
In Windows this works fine.
Now, since we get ACPI Notify() to the root port and not to the PXSX device
we should actually start our scan from there as well and not from the
non-existent PXSX device. Fix this by checking presence of the slot itself
(function 0) if we fail to do that otherwise.
While there use pci_bus_read_dev_vendor_id() in get_slot_status(), which is
the recommended way to read Device and Vendor IDs of devices on PCI buses.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198557 Reported-by: Mike Lothian <mike@fireburn.co.uk> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Just like many other Samsung models, the 670Z5E needs to use the acpi-video
backlight interface rather then the native one for backlight control to
work, add a quirk for this.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1557060 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We're supposed to be checking that "val_len" is not too large but
instead we check if it is smaller than the max.
The only function affected would be regmap_i2c_smbus_i2c_write() in
drivers/base/regmap/regmap-i2c.c. Strangely that function has its own
limit check which returns an error if (count >= I2C_SMBUS_BLOCK_MAX) so
it doesn't look like it has ever been able to do anything except return
an error.
Fixes: c335931ed9d2 ("regmap: Add raw_write/read checks for max_raw_write/read sizes") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 2cc42bac1c79 ("x86-64/Xen: eliminate W+X mappings") introduced a
call to get_cpu_cap, which is fstack-protected. This is works on x86-64
as commit 4f277295e54c ("x86/xen: init %gs very early to avoid page
faults with stack protector") ensures the stack protector is configured,
but it it did not cover x86-32.
Delay calling get_cpu_cap until after xen_setup_gdt has initialized the
stack canary. Without this, a 32bit PV machine crashes early
in boot.
(XEN) Domain 0 (vcpu#0) crashed on cpu#0:
(XEN) ----[ Xen-4.6.6-xc x86_64 debug=n Tainted: C ]----
(XEN) CPU: 0
(XEN) RIP: e019:[<00000000c10362f8>]
And the PV kernel IP corresponds to init_scattered_cpuid_features
0xc10362f8 <+24>: mov %gs:0x14,%eax
When a BRx is provided by a pipeline, the WPF must determine the master
layer. Currently the condition to check this identifies pipe->bru ||
pipe->num_inputs > 1.
The code then moves on to dereference pipe->bru, thus the check fails
static analysers on the possibility that pipe->num_inputs could be
greater than 1 without pipe->bru being set.
The reality is that the pipeline must have a BRx to support more than
one input, thus this could never cause a fault - however it also
identifies that the num_inputs > 1 check is redundant.
Remove the redundant check - and always configure the master layer
appropriately when we have a BRx configured in our pipeline.
Commit 9b61e302210e (spi: Pick spi bus number from Linux idr or spi alias)
ceased to unregister SPI buses with fixed bus numbers. Moreover this is
visible only if CONFIG_SPI_DEBUG=y is set or when trying to re-register
the same SPI controller.
modprobe spi_pxa2xx_platform:
[ 37.883137] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:19.0/pxa2xx-spi.12/spi_master/spi1'
[ 37.894984] CPU: 1 PID: 1467 Comm: modprobe Not tainted 4.16.0-rc4+ #21
[ 37.902384] Call Trace:
...
[ 38.122680] kobject_add_internal failed for spi1 with -EEXIST, don't try to register things with the same name in the same directory.
[ 38.136154] WARNING: CPU: 1 PID: 1467 at lib/kobject.c:238 kobject_add_internal+0x2a5/0x2f0
...
[ 38.513817] pxa2xx-spi pxa2xx-spi.12: problem registering spi master
[ 38.521036] pxa2xx-spi: probe of pxa2xx-spi.12 failed with error -17
Fix this by not returning immediately from spi_unregister_controller() if
idr_find() doesn't find controller with given ID/bus number. It finds
only those controllers that were registered with dynamic SPI bus
numbers. Only conditional cleanup between dynamic and fixed bus numbers
is to remove allocated IDR.
Fixes: 9b61e302210e (spi: Pick spi bus number from Linux idr or spi alias) Cc: stable@vger.kernel.org Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When SPI transfers can be offloaded using DMA, the SPI core need to
build a scatterlist to make sure that the buffer to be transferred is
dma-able.
This patch fixes the scatterlist entry size computation in the case
where the maximum acceptable scatterlist entry supported by the DMA
controller is less than PAGE_SIZE, when the buffer is vmalloced.
For each entry, the actual size is given by the minimum between the
desc_len (which is the max buffer size supported by the DMA controller)
and the remaining buffer length until we cross a page boundary.
Fixes: 65598c13fd66 ("spi: Fix per-page mapping of unaligned vmalloc-ed buffer") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The datasheet recommends initializing FIFOs before
SPI enable. If we do not do it like this, there may be
a strange behavior. We noticed that DMA does not work properly
with FIFOs if we do not clear them beforehand or enable them
before SPIEN.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The compatible string is incorrect. Add atmel,sama5d3-pinctrl since
it's the appropriate compatible string. Remove the
atmel,at91rm9200-pinctrl compatible string, this fallback is
useless, there are too many changes.
The proper name for the property, which assign given device to IOMMU is
'iommus', not 'iommu'. Fix incorrect name and let all GScaler devices
to be properly handled when IOMMU support is enabled.
Reported-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 6cbfdd73a94f ("ARM: dts: add sysmmu nodes for exynos5250") Cc: <stable@vger.kernel.org> # v4.8+ Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.
Fix that USB initialization fails as below runtime log is present during
booting on bananapi-r2 board by adding missing regulators the USB device
requires. Current regulators USB device uses are being updated with the
correct ones to reflect real configurations which are all from fixed
regulators rather than MT6323 one's output.
xhci-mtk 1a1c0000.usb: 1a1c0000.usb supply vbus not found, using dummy regulator
xhci-mtk 1a240000.usb: 1a240000.usb supply vbus not found, using dummy regulator
Cc: stable@vger.kernel.org Fixes: f4ff257cd160 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board") Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: update kernel log in commit message] Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Since commit 04c8b0f82c7d ("irqchip/gic: Make locking a BL_SWITCHER only
feature") coupled CPU idle freezes from time to time on Exynos4210. Later
commit 313c8c16ee62 ("PM / CPU: replace raw_notifier with atomic_notifier")
changed the context in which the CPU idle code is executed, what results
in fully reproducible freeze all the time. However, almost the same coupled
CPU idle code works fine on Exynos3250 regardless of the changes made in
the mentioned commits.
It turned out that the IPI call used on Exynos4210 is conflicting with the
change done in the first mentioned commit in GIC. Fix this by using the
same code path as for Exynos3250, instead of the IPI call for
synchronization with second CPU core, call dsb_sev() directly.
Tested on Exynos4210-based Trats and Origen boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> CC: <stable@vger.kernel.org> # v4.13+ Acked-by: Marc Zyngier <marc.zyngier@arm.com> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
vgic_copy_lpi_list() parses the LPI list and picks LPIs targeting
a given vcpu. We allocate the array containing the intids before taking
the lpi_list_lock, which means we can have an array size that is not
equal to the number of LPIs.
This is particularly obvious when looking at the path coming from
vgic_enable_lpis, which is not a command, and thus can run in parallel
with commands:
At that stage, we will happily overrun the intids array. Boo. An easy
fix is is to break once the array is full. The MAPI command will update
the config anyway, and we won't miss a thing. We also make sure that
lpi_list_count is read exactly once, so that further updates of that
value will not affect the array bound check.
Different modules maybe installed by the user on the eMMC connector
of the odroid-c2. While the red modules are working without an issue,
it seems some black modules (apparently Samsung based) are having
issue at 200MHz
While the tuning algorithm introduced in v4.14 enables high speed modes
on every other tested designs, it seems a problem remains for this
particular combination of board and eMMC module.
Lowering the maximum frequency of the eMMC on this board until we can
figure out a better solution.
The AXP223 PMIC, like the AXP221, does not generate VBUS change
interrupts when N_VBUSEN is used to drive VBUS for the OTG port
on the board.
This was not noticed until recently, as most A23/A33 boards use
a GPIO pin that does not support interrupts for OTG ID detection.
This forces the driver to use polling. However the A33-OlinuXino
uses a pin that does support interrupts, so the driver uses them.
However the VBUS interrupt never fires, and the driver never gets
to update the VBUS status. This results in musb timing out waiting
for VBUS to rise.
This was worked around for the AXP221 by resorting to polling
changes in commit 91d96f06a760 ("phy-sun4i-usb: Add workaround for
missing Vbus det interrupts on A31"). This patch adds the A23 and
A33 to the list of SoCs that need the workaround.
Fixes: fc1f45ed3043 ("phy-sun4i-usb: Add support for the usb-phys on the
sun8i-a33 SoC") Fixes: 123dfdbcfaf5 ("phy-sun4i-usb: Add support for the usb-phys on the
sun8i-a23 SoC") Cc: <stable@vger.kernel.org> # 4.3.x: 68dbc2ce77bb phy-sun4i-usb:
Use of_match_node to get model specific config data Cc: <stable@vger.kernel.org> # 4.3.x: 5cf700ac9d50 phy: phy-sun4i-usb:
Fix optional gpios failing probe Cc: <stable@vger.kernel.org> # 4.3.x: 04e59a0211ff phy-sun4i-usb:
Fix irq free conditions to match request conditions Cc: <stable@vger.kernel.org> # 4.3.x: 91d96f06a760 phy-sun4i-usb:
Add workaround for missing Vbus det interrupts on A31 Cc: <stable@vger.kernel.org> # 4.3.x Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
cache_reap() is initially scheduled in start_cpu_timer() via
schedule_delayed_work_on(). But then the next iterations are scheduled
via schedule_delayed_work(), i.e. using WORK_CPU_UNBOUND.
Thus since commit ef557180447f ("workqueue: schedule WORK_CPU_UNBOUND
work on wq_unbound_cpumask CPUs") there is no guarantee the future
iterations will run on the originally intended cpu, although it's still
preferred. I was able to demonstrate this with
/sys/module/workqueue/parameters/debug_force_rr_cpu. IIUC, it may also
happen due to migrating timers in nohz context. As a result, some cpu's
would be calling cache_reap() more frequently and others never.
This patch uses schedule_delayed_work_on() with the current cpu when
scheduling the next iteration.
Link: http://lkml.kernel.org/r/20180411070007.32225-1-vbabka@suse.cz Fixes: ef557180447f ("workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs") Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Pekka Enberg <penberg@kernel.org> Acked-by: Christoph Lameter <cl@linux.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: David Rientjes <rientjes@google.com> Cc: Tejun Heo <tj@kernel.org> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Stephen Boyd <sboyd@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
syzbot reported a use-after-free of shm_file_data(file)->file->f_op in
shm_get_unmapped_area(), called via sys_remap_file_pages().
Unfortunately it couldn't generate a reproducer, but I found a bug which
I think caused it. When remap_file_pages() is passed a full System V
shared memory segment, the memory is first unmapped, then a new map is
created using the ->vm_file. Between these steps, the shm ID can be
removed and reused for a new shm segment. But, shm_mmap() only checks
whether the ID is currently valid before calling the underlying file's
->mmap(); it doesn't check whether it was reused. Thus it can use the
wrong underlying file, one that was already freed.
Fix this by making the "outer" shm file (the one that gets put in
->vm_file) hold a reference to the real shm file, and by making
__shm_open() require that the file associated with the shm ID matches
the one associated with the "outer" file.
Taking the reference to the real shm file is needed to fully solve the
problem, since otherwise sfd->file could point to a freed file, which
then could be reallocated for the reused shm ID, causing the wrong shm
segment to be mapped (and without the required permission checks).
Commit 1ac0b6dec656 ("ipc/shm: handle removed segments gracefully in
shm_mmap()") almost fixed this bug, but it didn't go far enough because
it didn't consider the case where the shm ID is reused.
The following program usually reproduces this bug:
int main()
{
int is_parent = (fork() != 0);
srand(getpid());
for (;;) {
int id = shmget(0xF00F, 4096, IPC_CREAT|0700);
if (is_parent) {
void *addr = shmat(id, NULL, 0);
usleep(rand() % 50);
while (!syscall(__NR_remap_file_pages, addr, 4096, 0, 0, 0));
} else {
usleep(rand() % 50);
shmctl(id, IPC_RMID, NULL);
}
}
}
It causes the following NULL pointer dereference due to a 'struct file'
being used while it's being freed. (I couldn't actually get a KASAN
use-after-free splat like in the syzbot report. But I think it's
possible with this bug; it would just take a more extraordinary race...)
We've got a bug report indicating a kernel panic at booting on an x86-32
system, and it turned out to be the invalid PCI resource assigned after
reallocation. __find_resource() first aligns the resource start address
and resets the end address with start+size-1 accordingly, then checks
whether it's contained. Here the end address may overflow the integer,
although resource_contains() still returns true because the function
validates only start and end address. So this ends up with returning an
invalid resource (start > end).
There was already an attempt to cover such a problem in the commit 47ea91b4052d ("Resource: fix wrong resource window calculation"), but
this case is an overseen one.
This patch adds the validity check of the newly calculated resource for
avoiding the integer overflow problem.
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1086739 Link: http://lkml.kernel.org/r/s5hpo37d5l8.wl-tiwai@suse.de Fixes: 23c570a67448 ("resource: ability to resize an allocated resource") Signed-off-by: Takashi Iwai <tiwai@suse.de> Reported-by: Michael Henders <hendersm@shaw.ca> Tested-by: Michael Henders <hendersm@shaw.ca> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
One use of the reiserfs_warning() macro in journal_init_dev() is missing
a parameter, causing the following warning:
REISERFS warning (device loop0): journal_init_dev: Cannot open '%s': %i journal_init_dev:
This also causes a WARN_ONCE() warning in the vsprintf code, and then a
panic if panic_on_warn is set.
Please remove unsupported %/ in format string
WARNING: CPU: 1 PID: 4480 at lib/vsprintf.c:2138 format_decode+0x77f/0x830 lib/vsprintf.c:2138
Kernel panic - not syncing: panic_on_warn set ...
Just add another string argument to the macro invocation.
The original intent for always adding the anonymous struct in
task_struct was to make sure we had compiler coverage.
However, this caused pathological padding of 40 bytes at the start of
task_struct. Instead, move the anonymous struct to being only used when
struct layout randomization is enabled.
When using KSM with use_zero_pages, we replace anonymous pages
containing only zeroes with actual zero pages, which are not anonymous.
We need to do proper accounting of the mm counters, otherwise we will
get wrong values in /proc and a BUG message in dmesg when tearing down
the mm.
Link: http://lkml.kernel.org/r/1522931274-15552-1-git-send-email-imbrenda@linux.vnet.ibm.com Fixes: e86c59b1b1 ("mm/ksm: improve deduplication of zero pages with colouring") Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Hugh Dickins <hughd@google.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
While UBI and UBIFS seem to work at first sight with MLC NAND, you will
most likely lose all your data upon a power-cut or due to read/write
disturb.
In order to protect users from bad surprises, refuse to attach to MLC
NAND.
When opening a device with write access, ubiblock_open returns an error
code. Currently, this error code is -EPERM, but this is not the right
value.
The open function for other block devices returns -EROFS when opening
read-only devices with FMODE_WRITE set. When used with dm-verity, the
veritysetup userspace tool is expecting EROFS, and refuses to use the
ubiblock device.
Use -EROFS for ubiblock as well. As a result, veritysetup accepts the
ubiblock device as valid.
Cc: stable@vger.kernel.org Fixes: 9d54c8a33eec (UBI: R/O block driver on top of UBI volumes) Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If ubifs_wbuf_sync() fails we must not write a master node with the
dirty marker cleared.
Otherwise it is possible that in case of an IO error while syncing we
mark the filesystem as clean and UBIFS refuses to recover upon next
mount.
With commit e948bc8fbee0 (cpufreq: Cap the default transition delay
value to 10 ms) the cpufreq was not honouring the delay passed via
ACPI (PCCT). Due to which on ARM based platforms using CPPC the
cpufreq governor tries to change the frequency of CPUs faster than
expected.
This leads to continuous error messages like the following.
" ACPI CPPC: PCC check channel failed. Status=0 "
Earlier (without above commit) the default transition delay was
taken form the value passed from PCCT. Use the same value provided
by PCCT to set the transition_delay_us.
Fixes: e948bc8fbee0 (cpufreq: Cap the default transition delay value to 10 ms) Signed-off-by: George Cherian <george.cherian@cavium.com> Cc: 4.14+ <stable@vger.kernel.org> # 4.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Brad Figg <brad.figg@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A tty is hung up by __tty_hangup() setting file->f_op to
hung_up_tty_fops, which is skipped on ttys whose write operation isn't
tty_write(). This means that, for example, /dev/console whose write
op is redirected_tty_write() is never actually marked hung up.
Because n_tty_read() uses the hung up status to decide whether to
abort the waiting readers, the lack of hung-up marking can lead to the
following scenario.
1. A session contains two processes. The leader and its child. The
child ignores SIGHUP.
2. The leader exits and starts disassociating from the controlling
terminal (/dev/console).
3. __tty_hangup() skips setting f_op to hung_up_tty_fops.
4. SIGHUP is delivered and ignored.
5. tty_ldisc_hangup() is invoked. It wakes up the waits which should
clear the read lockers of tty->ldisc_sem.
6. The reader wakes up but because tty_hung_up_p() is false, it
doesn't abort and goes back to sleep while read-holding
tty->ldisc_sem.
7. The leader progresses to tty_ldisc_lock() in tty_ldisc_hangup()
and is now stuck in D sleep indefinitely waiting for
tty->ldisc_sem.
The following is Alan's explanation on why some ttys aren't hung up.
1. It broke the serial consoles because they would hang up and close
down the hardware. With tty_port that *should* be fixable properly
for any cases remaining.
2. The console layer was (and still is) completely broken and doens't
refcount properly. So if you turn on console hangups it breaks (as
indeed does freeing consoles and half a dozen other things).
As neither can be fixed quickly, this patch works around the problem
by introducing a new flag, TTY_HUPPING, which is used solely to tell
n_tty_read() that hang-up is in progress for the console and the
readers should be aborted regardless of the hung-up status of the
device.
The following is a sample hung task warning caused by this issue.
INFO: task agetty:2662 blocked for more than 120 seconds.
Not tainted 4.11.3-dbg-tty-lockup-02478-gfd6c7ee-dirty #28
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
0 2662 1 0x00000086
Call Trace:
__schedule+0x267/0x890
schedule+0x36/0x80
schedule_timeout+0x23c/0x2e0
ldsem_down_write+0xce/0x1f6
tty_ldisc_lock+0x16/0x30
tty_ldisc_hangup+0xb3/0x1b0
__tty_hangup+0x300/0x410
disassociate_ctty+0x6c/0x290
do_exit+0x7ef/0xb00
do_group_exit+0x3f/0xa0
get_signal+0x1b3/0x5d0
do_signal+0x28/0x660
exit_to_usermode_loop+0x46/0x86
do_syscall_64+0x9c/0xb0
entry_SYSCALL64_slow_path+0x25/0x25
The following is the repro. Run "$PROG /dev/console". The parent
process hangs in D state.
/*
* The child ignores SIGHUP and keeps reading from the controlling
* tty. Because SIGHUP is ignored, the child doesn't get killed on
* parent exit and the bug in n_tty makes the read(2) block the
* parent's control terminal hangup attempt. The parent ends up in
* D sleep until the child is explicitly killed.
*/
sigaction(SIGHUP, &sact, NULL);
printf("Child reading tty\n");
while (1) {
char buf[1024];
Andy Whitcroft [Tue, 29 May 2018 13:38:27 +0000 (14:38 +0100)]
UBUNTU: SAUCE: floppy: Do not copy a kernel pointer to user memory in FDGETPRM ioctl
The final field of a floppy_struct is the field "name", which is a pointer
to a string in kernel memory. The kernel pointer should not be copied to
user memory. The FDGETPRM ioctl copies a floppy_struct to user memory,
including this "name" field. This pointer cannot be used by the user
and it will leak a kernel address to user-space, which will reveal the
location of kernel code and data and undermine KASLR protection.
Model this code after the compat ioctl which copies the returned data
to a previously cleared temporary structure on the stack (excluding the
name pointer) and copy out to userspace from there. As we already have
an inparam union with an appropriate member and that memory is already
cleared even for read only calls make use of that as a temporary store.
Based on an initial patch by Brian Belleville.
CVE-2018-7755 Signed-off-by: Andy Whitcroft <apw@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Juerg Haefliger <juergh@canonical.com>
James Morse [Wed, 2 May 2018 20:39:00 +0000 (22:39 +0200)]
arm64: sdei: Add trampoline code for remapping the kernel
BugLink: https://bugs.launchpad.net/bugs/1768630
When CONFIG_UNMAP_KERNEL_AT_EL0 is set the SDEI entry point and the rest
of the kernel may be unmapped when we take an event. If this may be the
case, use an entry trampoline that can switch to the kernel page tables.
We can't use the provided PSTATE to determine whether to switch page
tables as we may have interrupted the kernel's entry trampoline, (or a
normal-priority event that interrupted the kernel's entry trampoline).
Instead test for a user ASID in ttbr1_el1.
Save a value in regs->addr_limit to indicate whether we need to restore
the original ASID when returning from this event. This value is only used
by do_page_fault(), which we don't call with the SDEI regs.
Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
(cherry picked from commit 79e9aa59dc29a995921fb01e64cd36b73cf5abe0) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Tyler Baicar [Mon, 7 May 2018 22:07:00 +0000 (00:07 +0200)]
ACPI: APEI: call into AER handling regardless of severity
BugLink: https://bugs.launchpad.net/bugs/1769730
Currently the GHES code only calls into the AER driver for
recoverable type errors. This is incorrect because errors of
other severities do not get logged by the AER driver and do not
get exposed to user space via the AER trace event. So, call
into the AER driver for PCIe errors regardless of the severity
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org> Reviewed-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 9852ce9ae213d39a98f161db84b90b047fbdc436) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Hannes Reinecke [Sat, 12 May 2018 21:37:22 +0000 (18:37 -0300)]
scsi: qla2xxx: Fixup locking for session deletion
BugLink: http://bugs.launchpad.net/bugs/1770003
Commit d8630bb95f46 ('Serialize session deletion by using work_lock')
tries to fixup a deadlock when deleting sessions, but fails to take into
account the locking rules. This patch resolves the situation by
introducing a separate lock for processing the GNLIST response, and
ensures that sess_lock is released before calling
qlt_schedule_sess_delete().
Cc: Himanshu Madhani <himanshu.madhani@cavium.com> Cc: Quinn Tran <quinn.tran@cavium.com> Fixes: d8630bb95f46 ("scsi: qla2xxx: Serialize session deletion by using work_lock") Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(backported from upstream ZFS commit 1c6cacf4ea6c04a58a0e3057f5ed60c24a4ffeff) Signed-off-by: Breno Leitao <brenohl@br.ibm.com> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
When the qla2xxx firmware is unavailable, eventually
qla2x00_sp_timeout() is reached, which calls the timeout function and
frees the srb_t instance.
The timeout function always resolves to qla2x00_async_iocb_timeout(),
which invokes another callback function called "done". All of these
qla2x00_*_sp_done() callbacks also free the srb_t instance; after
returning to qla2x00_sp_timeout(), it is freed again.
The fix is to remove the "sp->free(sp)" call from qla2x00_sp_timeout()
and add it to those code paths in qla2x00_async_iocb_timeout() which
do not already free the object.
This is how it looks like with KASAN:
BUG: KASAN: use-after-free in qla2x00_sp_timeout+0x228/0x250
Read of size 8 at addr ffff88278147a590 by task swapper/2/0
Allocated by task 1502:
save_stack+0x33/0xa0
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc+0xb8/0x1c0
mempool_alloc+0xd6/0x260
qla24xx_async_gnl+0x3c5/0x1100
The buggy address belongs to the object at ffff88278147a440
which belongs to the cache qla2xxx_srbs of size 344
The buggy address is located 336 bytes inside of
344-byte region [ffff88278147a440, ffff88278147a598)
Reported-by: Max Kellermann <mk@cm4all.com> Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Cc: Max Kellermann <mk@cm4all.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from eaf75d1815dad230dac2f1e8f1dc0349b2d50071) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Quinn Tran [Thu, 28 Dec 2017 20:33:41 +0000 (12:33 -0800)]
scsi: qla2xxx: Prevent relogin trigger from sending too many commands
BugLink: http://bugs.launchpad.net/bugs/1770003
This patch adds check for pending work event before queueing
relogin work to prevent redundant work to be active at the
same time.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from 6d67492764b39ad6efb6822816ad73dc141752f4) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
scsi: qla2xxx: Don't call dma_free_coherent with IRQ disabled.
BugLink: http://bugs.launchpad.net/bugs/1770003
The logo ELS command allocates dma coherent memory for the
data payload and serialize the completions. When this command
times out, the timeout routine completes the thread waiting
for completion which in turn cleanup resources allocated for
this ELS command processing. Don't call generic sp->free
routine when this ELS command times out to avoid to double
freeing of the same resources.
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from 045d6ea200af794ba15515984cff63787a7fc3c0) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Quinn Tran [Thu, 28 Dec 2017 20:33:43 +0000 (12:33 -0800)]
scsi: qla2xxx: Serialize session deletion by using work_lock
BugLink: http://bugs.launchpad.net/bugs/1770003
for session deletion, replace sess_lock with work_lock.
Under certain case sess_lock is not feasiable to acquire.
The lock is needed temporarily to make sure a single
call to schedule of the work element.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(backported from d8630bb95f46ea118dede63bd75533faa64f9612) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Quinn Tran [Thu, 28 Dec 2017 20:33:42 +0000 (12:33 -0800)]
scsi: qla2xxx: Remove unused argument from qlt_schedule_sess_for_deletion()
BugLink: http://bugs.launchpad.net/bugs/1770003
Immeadiate flag is not used for scheduling session deletion.
Remove it to simplfy session deletion code path.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(backported from 94cff6e114df56d0df74cdabe3481df38d9b0c1e) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1770003
When connection type is N_Port to N_Port (point-to-point), there
is a possibilty where initiator will not send PLOGI request and
will directly send PRLI. In N2N connection the port has higher
port name sends the PLOGI but not allow to send PRLI if is a
target mode. Only initiator is allowed to send PRLI.
Current driver code deletes old session when it receives PLOGI
request. If we will not receive PLOGI request then we will not
delete old session and create new session. Add check for N2N
with PRLI receive only and trigger cleanup. For this case, the
cleanup requires individual cmd abort instead of using implicit
logout as a broad stroke flush.
Signed-off-by: Krishna Kant <krishna.kant@purestorage.com> Signed-off-by: Alexei Potashnik <alexei@purestorage.com> Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(backported from 9cd883f07a54e5301d51e259acd250bb035996be) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
- Correct return status of phy_up_v3_hw() and phy_bcast_v3_hw()
- Add static for function phy_get_max_linkrate_v3_hw()
- Change exception return status when no reset method
- Change magic value to ts->stat in slot_complete_vx_hw()
- Remove unnecessary check for dev_is_sata()
- Fix some issues of alignment and indents (Authored by Xiaofei Tan in
another patch, but added here to be practical)
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit edafeef4f28ded4ea9ba7876cc35861d43c7b2b1) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:11 +0000 (20:25 +0800)]
scsi: hisi_sas: fix return value of hisi_sas_task_prep()
BugLink: https://bugs.launchpad.net/bugs/1768974
It is an implicit regulation that error code that function returned should
be negative. But hisi_sas_task_prep() doesn't follow this. This may cause
problems in the upper layer code.
For example, in sas_expander.c of libsas, smp_execute_task_sg() may return
the number of bytes of underrun. It will be conflicted with the scenaio
lldd_execute_task() return an positive error code.
This patch change the return value from SAS_PHY_DOWN to -ECOMM in
hisi_sas_task_prep().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 6bf6db518cd10ad57e659607d0abece1b81956c6) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1768974
The structure element hisi_sas_devices.running_req to count how many
commands are active is in effect only ever written in the code, so remove
it.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 36996a1e6dff4e5835faeb00ba920ccb9a07aa52) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The reason is that the internal abort task could be blocked in HW if the HW
is retrying to set up link. The internal abort task will be executed only
when the retry process finished.
The maximum time is 5s for the retry of setting up link. So, the timer
expire should be more than 5s. This patch increases it from 110ms to 6s.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit bb9abc4af5449d2a72cda876be950988e8b2b888) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:08 +0000 (20:25 +0800)]
scsi: hisi_sas: fix the issue of setting linkrate register
BugLink: https://bugs.launchpad.net/bugs/1768974
It is not right to set the register PROG_PHY_LINK_RATE while PHY is still
enabled. So if we want to change PHY linkrate, we need to disable PHY before
setting the register PROG_PHY_LINK_RATE, and then start-up PHY. This patch
is to fix this issue.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 0006ce29e87ba357f64ee73e92c8aefc270fd315) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:07 +0000 (20:25 +0800)]
scsi: hisi_sas: fix the issue of link rate inconsistency
BugLink: https://bugs.launchpad.net/bugs/1768974
In sysfs, there are two files about minimum linkrate, and also two files for
maximum linkrate. Take maximum linkrate example, maximum_linkrate_hw is
read-only and indicated by the register HARD_PHY_LINKRATE, and
maximum_linkrate is read-write and corresponding to the register
PROG_PHY_LINK_RATE.
But in the function phy_up_v*_hw(), we get *_linkrate value from
HARD_PHY_LINKRATE. It is not right. This patch is to fix this issue.
Unreferenced PHY-interrupt enum is also removed for v3 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit eba8c20c7178af9673ad842b0f68251c891c8546) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:06 +0000 (20:25 +0800)]
scsi: hisi_sas: support the property of signal attenuation for v2 hw
BugLink: https://bugs.launchpad.net/bugs/1768974
The register SAS_PHY_CTRL is configured according to signal quality. The
signal quality is calculated by signal attenuation of hardware physical
link. It may be different for different PCB layout.
So, in order to give better support to new board, this patch add support to
reading the devicetree property, "hisilicon,signal-attenuation". Of course,
we still keep an default value in driver to adapt old board.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 67c2bf23314170a17f2aefec4f0aaa4881b72181) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Xiaofei Tan [Wed, 7 Mar 2018 12:25:05 +0000 (20:25 +0800)]
scsi: hisi_sas: dt-bindings: add an property of signal attenuation
BugLink: https://bugs.launchpad.net/bugs/1768974
For some new boards with hip07 chipset we are required to set PHY config
registers differently. The hw property which determines how to set these
registers is in the PHY signal attenuation readings.
This patch add an devicetree property, "hisilicon,signal-attenuation", which
is used to describe the signal attenuation of an board.
Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 4c40db995eb54c3ee8cb5a8340640f49395d5f9e) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Max Gurtovoy [Mon, 7 May 2018 21:33:00 +0000 (23:33 +0200)]
nvme-rdma: Don't flush delete_wq by default during remove_one
BugLink: http://bugs.launchpad.net/bugs/1764982
The .remove_one function is called for any ib_device removal.
In case the removed device has no reference in our driver, there
is no need to flush the work queue.
Reviewed-by: Israel Rukshin <israelr@mellanox.com> Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
(cherry picked from commit 9bad0404ecd7594265cef04e176adeaa4ffbca4a) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Max Gurtovoy [Mon, 7 May 2018 21:33:00 +0000 (23:33 +0200)]
nvmet-rdma: Don't flush system_wq by default during remove_one
BugLink: http://bugs.launchpad.net/bugs/1764982
The .remove_one function is called for any ib_device removal.
In case the removed device has no reference in our driver, there
is no need to flush the system work queue.
Reviewed-by: Israel Rukshin <israelr@mellanox.com> Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
(cherry picked from commit a3dd7d0022c347207ae931c753a6dc3e6e8fcbc1) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Jason Yan [Thu, 3 May 2018 21:49:00 +0000 (23:49 +0200)]
scsi: libsas: defer ata device eh commands to libata
BugLink: https://bugs.launchpad.net/bugs/1768971
When ata device doing EH, some commands still attached with tasks are
not passed to libata when abort failed or recover failed, so libata did
not handle these commands. After these commands done, sas task is freed,
but ata qc is not freed. This will cause ata qc leak and trigger a
warning like below:
If ata qc leaked too many, ata tag allocation will fail and io blocked
for ever.
As suggested by Dan Williams, defer ata device commands to libata and
merge sas_eh_finish_cmd() with sas_eh_defer_cmd(). libata will handle
ata qcs correctly after this.
Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: Xiaofei Tan <tanxiaofei@huawei.com> CC: John Garry <john.garry@huawei.com> CC: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
(cherry picked from commit 318aaf34f1179b39fa9c30fa0f3288b645beee39) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
[115946.152283] Unable to handle kernel NULL pointer dereference at virtual address 000007d8
[115946.223963] CPU: 0 PID: 22175 Comm: kworker/0:1 Tainted: G W OEL 4.14.0 #1
[115946.232925] Workqueue: events ata_scsi_hotplug
[115946.237938] task: ffff8021ee50b180 task.stack: ffff00000d5d0000
[115946.244717] PC is at sas_find_dev_by_rphy+0x44/0x114
[115946.250224] LR is at sas_find_dev_by_rphy+0x3c/0x114
......
[115946.355701] Process kworker/0:1 (pid: 22175, stack limit = 0xffff00000d5d0000)
[115946.363369] Call trace:
[115946.456356] [<ffff000008878a9c>] sas_find_dev_by_rphy+0x44/0x114
[115946.462908] [<ffff000008878b8c>] sas_target_alloc+0x20/0x5c
[115946.469408] [<ffff00000885a31c>] scsi_alloc_target+0x250/0x308
[115946.475781] [<ffff00000885ba30>] __scsi_add_device+0xb0/0x154
[115946.481991] [<ffff0000088b520c>] ata_scsi_scan_host+0x180/0x218
[115946.488367] [<ffff0000088b53d8>] ata_scsi_hotplug+0xb0/0xcc
[115946.494801] [<ffff0000080ebd70>] process_one_work+0x144/0x390
[115946.501115] [<ffff0000080ec100>] worker_thread+0x144/0x418
[115946.507093] [<ffff0000080f2c98>] kthread+0x10c/0x138
[115946.512792] [<ffff0000080855dc>] ret_from_fork+0x10/0x18
We found that Ding Xiang has reported a similar bug before:
https://patchwork.kernel.org/patch/9179817/
And this bug still exists in mainline. Since libsas handles hotplug and
device adding/removing itself, do not need to schedule ata hot plug task
here if it is a sas host.
Signed-off-by: Jason Yan <yanaijie@huawei.com> Cc: Ding Xiang <dingxiang@huawei.com> Cc: stable@vger.kernel.org Signed-off-by: Tejun Heo <tj@kernel.org>
(cherry picked from commit 6f54120e17e311fd7ac42b9ec2a0611caa5b46ad) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Nicholas Piggin [Mon, 30 Apr 2018 16:57:00 +0000 (18:57 +0200)]
powerpc/64s: sreset panic if there is no debugger or crash dump handlers
BugLink: http://bugs.launchpad.net/bugs/1767927
system_reset_exception does most of its own crash handling now,
invoking the debugger or crash dumps if they are registered. If not,
then it goes through to die() to print stack traces, and then is
supposed to panic (according to comments).
However after die() prints oopses, it does its own handling which
doesn't allow system_reset_exception to panic (e.g., it may just
kill the current process). This patch causes sreset exceptions to
return from die after it prints messages but before acting.
This also stops die from invoking the debugger on 0x100 crashes.
system_reset_exception similarly calls the debugger. It had been
thought this was harmless (because if the debugger was disabled,
neither call would fire, and if it was enabled the first call
would return). However in some cases like xmon 'X' command, the
debugger returns 0, which currently causes it to be entered
again (first in system_reset_exception, then in die), which is
confusing.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry-picked from d40b6768e45bd9213139b2d91d30c7692b6007b1) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Nicholas Piggin [Mon, 30 Apr 2018 16:57:00 +0000 (18:57 +0200)]
powerpc/64s: return more carefully from sreset NMI
BugLink: http://bugs.launchpad.net/bugs/1767927
System Reset, being an NMI, must return more carefully than other
interrupts. It has traditionally returned via the nromal return
from exception path, but that has a number of problems.
- r13 does not get restored if returning to kernel. This is for
interrupts which may cause a context switch, which sreset will
never do. Interrupting OPAL (which uses a different r13) is one
place where this causes breakage.
- It may cause several other problems returning to kernel with
preempt or TIF_EMULATE_STACK_STORE if it hits at the wrong time.
It's safer just to have a simple restore and return, like machine
check which is the other NMI.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(backported from 15b4dd7981496f51c5f9262a5e0761e48de6655f) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Nicholas Piggin [Mon, 30 Apr 2018 16:57:00 +0000 (18:57 +0200)]
powerpc/powernv: Handle unknown OPAL errors in opal_nvram_write()
BugLink: http://bugs.launchpad.net/bugs/1767927
opal_nvram_write currently just assumes success if it encounters an
error other than OPAL_BUSY or OPAL_BUSY_EVENT. Have it return -EIO
on other errors instead.
Fixes: 628daa8d5abf ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks") Cc: stable@vger.kernel.org # v3.2+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com> Acked-by: Stewart Smith <stewart@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry-picked from 741de617661794246f84a21a02fc5e327bffc9ad) Signed-off-by: Gustavo Walbon <gwalbon@linux.vnet.ibm.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
BugLink: http://bugs.launchpad.net/bugs/1765564
fsnotify() acquires a reference to a fsnotify_mark_connector through
the SRCU-protected pointer to_tell->i_fsnotify_marks. However, it
appears that no precautions are taken in fsnotify_put_mark() to
ensure that fsnotify() drops its reference to this
fsnotify_mark_connector before assigning a value to its 'destroy_next'
field. This can result in fsnotify_put_mark() assigning a value
to a connector's 'destroy_next' field right before fsnotify() tries to
traverse the linked list referenced by the connector's 'list' field.
Since these two fields are members of the same union, this behavior
results in a kernel panic.
This issue is resolved by moving the connector's 'destroy_next' field
into the object pointer union. This should work since the object pointer
access is protected by both a spinlock and the value of the 'flags'
field, and the 'flags' field is cleared while holding the spinlock in
fsnotify_put_mark() before 'destroy_next' is updated. It shouldn't be
possible for another thread to accidentally read from the object pointer
after the 'destroy_next' field is updated.
The offending behavior here is extremely unlikely; since
fsnotify_put_mark() removes references to a connector (specifically,
it ensures that the connector is unreachable from the inode it was
formerly attached to) before updating its 'destroy_next' field, a
sizeable chunk of code in fsnotify_put_mark() has to execute in the
short window between when fsnotify() acquires the connector reference
and saves the value of its 'list' field. On the HEAD kernel, I've only
been able to reproduce this by inserting a udelay(1) in fsnotify().
However, I've been able to reproduce this issue without inserting a
udelay(1) anywhere on older unmodified release kernels, so I believe
it's worth fixing at HEAD.
References: https://bugzilla.kernel.org/show_bug.cgi?id=199437 Fixes: 08991e83b7286635167bab40927665a90fb00d81 CC: stable@vger.kernel.org Signed-off-by: Robert Kolchmeyer <rkolchmeyer@google.com> Signed-off-by: Jan Kara <jack@suse.cz>
(cherry picked from commit d90a10e2444ba5a351fa695917258ff4c5709fa5) Signed-off-by: Seyeong Kim <seyeong.kim@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Jason Andryuk [Fri, 18 May 2018 14:59:00 +0000 (16:59 +0200)]
xen-netfront: Fix hang on device removal
BugLink: http://bugs.launchpad.net/bugs/1771620
A toolstack may delete the vif frontend and backend xenstore entries
while xen-netfront is in the removal code path. In that case, the
checks for xenbus_read_driver_state would return XenbusStateUnknown, and
xennet_remove would hang indefinitely. This hang prevents system
shutdown.
xennet_remove must be able to handle XenbusStateUnknown, and
netback_changed must also wake up the wake_queue for that state as well.
Fixes: 5b5971df3bc2 ("xen-netfront: remove warning when unloading module") Signed-off-by: Jason Andryuk <jandryuk@gmail.com> Cc: Eduardo Otubo <otubo@redhat.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
(cherry picked from commit c2d2e6738a209f0f9dffa2dc8e7292fc45360d61) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
dann frazier [Sat, 21 Apr 2018 16:50:00 +0000 (18:50 +0200)]
net: hns: Avoid action name truncation
BugLink: https://bugs.launchpad.net/bugs/1765977
When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:
Signed-off-by: dann frazier <dann.frazier@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit f4ea89110df237da6fbcaab76af431e85f07d904) Signed-off-by: dann frazier <dann.frazier@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
[smb: applied with fuzz 2] Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Anju T Sudhakar [Fri, 18 May 2018 14:48:00 +0000 (16:48 +0200)]
UBUNTU: SAUCE: powerpc/perf: Fix memory allocation for core-imc based on num_possible_cpus()
BugLink: http://bugs.launchpad.net/bugs/1770849
Currently memory is allocated for core-imc based on cpu_present_mask, which
has bit 'cpu' set iff cpu is populated. We use (cpu number / threads per core)
as as array index to access the memory. So in a system with guarded cores,
since allocation happens based on cpu_present_mask, (cpu number / threads per core)
bounds the index and leads to memory overflow.
The issue is exposed in a guard test. The guard test will make some CPU's
as un-available to the system during boot time as well as at runtime. So
when the cpu is unavailable to the system during boot time, the memory
allocation happens depending on the number of available cpus. And when we
access the memory using (cpu number / threads per core) as the index the
system crashes due to memory overflow.
Allocating memory for core-imc based on cpu_possible_mask, which has bit
'cpu' set iff cpu is populatable, will fix this issue.
Reported-by: Pridhiviraj Paidipeddi <ppaidipe at linux.vnet.ibm.com> Signed-off-by: Anju T Sudhakar <anju at linux.vnet.ibm.com> Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Andy Whitcroft [Fri, 11 May 2018 23:20:00 +0000 (01:20 +0200)]
UBUNTU: [Config] update Build-Depends: transfig to fig2dev
Some time back transfig became a transitional package to fig2dev.
In cosmic this transitional has now been deprecated. As we are still
copying kernels forward we need to fix this dependency in bionic.
This transition actually occured back in artful, we just missed it.
Switch our build dependency to the "new" fig2dev package.
BugLink: http://bugs.launchpad.net/bugs/1770770 Signed-off-by: Andy Whitcroft <apw@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Shilpasri G Bhat [Fri, 18 May 2018 14:23:00 +0000 (16:23 +0200)]
cpufreq: powernv: Fix hardlockup due to synchronous smp_call in timer interrupt
BugLink: http://bugs.launchpad.net/bugs/1768898
gpstate_timer_handler() uses synchronous smp_call to set the pstate
on the requested core. This causes the below hard lockup:
One way to avoid this is removing the smp-call. We can ensure that the
timer always runs on one of the policy-cpus. If the timer gets
migrated to a cpu outside the policy then re-queue it back on the
policy->cpus. This way we can get rid of the smp-call which was being
used to set the pstate on the policy->cpus.
Fixes: 7bc54b652f13 ("timers, cpufreq/powernv: Initialize the gpstate timer as pinned") Cc: stable@vger.kernel.org # v4.8+ Reported-by: Nicholas Piggin <npiggin@gmail.com> Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com> Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Acked-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
(cherry picked from commit c0f7f5b6c69107ca92909512533e70258ee19188) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Xin Long [Fri, 20 Apr 2018 16:14:00 +0000 (18:14 +0200)]
xfrm: reuse uncached_list to track xdsts
BugLink: http://bugs.launchpad.net/bugs/1746474
In early time, when freeing a xdst, it would be inserted into
dst_garbage.list first. Then if it's refcnt was still held
somewhere, later it would be put into dst_busy_list in
dst_gc_task().
When one dev was being unregistered, the dev of these dsts in
dst_busy_list would be set with loopback_dev and put this dev.
So that this dev's removal wouldn't get blocked, and avoid the
kmsg warning:
kernel:unregister_netdevice: waiting for veth0 to become \
free. Usage count = 2
However after Commit 52df157f17e5 ("xfrm: take refcnt of dst
when creating struct xfrm_dst bundle"), the xdst will not be
freed with dst gc, and this warning happens.
To fix it, we need to find these xdsts that are still held by
others when removing the dev, and free xdst's dev and set it
with loopback_dev.
But unfortunately after flow_cache for xfrm was deleted, no
list tracks them anymore. So we need to save these xdsts
somewhere to release the xdst's dev later.
To make this easier, this patch is to reuse uncached_list to
track xdsts, so that the dev refcnt can be released in the
event NETDEV_UNREGISTER process of fib_netdev_notifier.
Thanks to Florian, we could move forward this fix quickly.
Fixes: 52df157f17e5 ("xfrm: take refcnt of dst when creating struct xfrm_dst bundle") Reported-by: Jianlin Shi <jishi@redhat.com> Reported-by: Hangbin Liu <liuhangbin@gmail.com> Tested-by: Eyal Birger <eyal.birger@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
(cherry picked from commit 510c321b557121861601f9d259aadd65aa274f35) Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Seth Forshee [Thu, 17 May 2018 15:25:00 +0000 (17:25 +0200)]
UBUNTU: [Config] Add nfp.ko to generic inclusion list
BugLink: http://bugs.launchpad.net/bugs/1768526
Move this to linux-modules so that VFs of Netronome Agilio
SmartNICs which have been made available to guests using PCI
pass-through can be used by those guests.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com> Acked-by: Khaled Elmously <khalid.elmously@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
x86/xen: Reset VCPU0 info pointer after shared_info remap
BugLink: http://bugs.launchpad.net/bugs/1771679
This patch fixes crashes during boot for HVM guests on older (pre HVM
vector callback) Xen versions. Without this, current kernels will always
fail to boot on those Xen versions.
During boot, the HYPERVISOR_shared_info page gets remapped to make it work
with KASLR. This means that any pointer derived from it needs to be
adjusted.
The only value that this applies to is the vcpu_info pointer for VCPU 0.
For PV and HVM with the callback vector feature, this gets done via the
smp_ops prepare_boot_cpu callback. Older Xen versions do not support the
HVM callback vector, so there is no Xen-specific smp_ops set up in that
scenario. So, the vcpu_info pointer for VCPU 0 never gets set to the proper
value, and the first reference of it will be bad. Fix this by resetting it
immediately after the remap.
Signed-off-by: Frank van der Linden <fllinden@amazon.com> Reviewed-by: Eduardo Valentin <eduval@amazon.com> Reviewed-by: Alakesh Haloi <alakeshh@amazon.com> Reviewed-by: Vallish Vaidyeshwara <vallish@amazon.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: xen-devel@lists.xenproject.org Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
(cherry picked from commit d1ecfa9d1f402366b1776fbf84e635678a51414f) Signed-off-by: Kamal Mostafa <kamal@canonical.com> Acked-by: Colin King <colin.king@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
The X86_FEATURE_SSBD is an synthetic CPU feature - that is
it bit location has no relevance to the real CPUID 0x7.EBX[31]
bit position. For that we need the new CPU feature name.
Fixes: 52817587e706 ("x86/cpufeatures: Disentangle SSBD enumeration") CC: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: stable@vger.kernel.org Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CVE-2018-3639 (x86)
(cherry-picked from https://patchwork.kernel.org/patch/10416823/) Signed-off-by: Stefan Bader <stefan.bader@canonical.com>