After a PWM is disposed by its user the per chip data becomes invalid.
Clear the data in common code instead of the device drivers to get
consistent behaviour. Before this patch only three of nine drivers
cleaned up here.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Errors are negative numbers. Using %u shows them as very large positive
numbers such as 4294967277 that don't make sense. Use the %d format
instead, and get a much nicer -19.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net> Fixes: b48e0bab142f ("net: macb: Migrate to devm clock interface") Fixes: 93b31f48b3ba ("net/macb: unify clock management") Fixes: 421d9df0628b ("net/macb: merge at91_ether driver into macb driver") Fixes: aead88bd0e99 ("net: ethernet: macb: Add support for rx_clk") Fixes: f5473d1d44e4 ("net: macb: Support clock management for tsu_clk") Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Add parent device name to the name of devices on bus to avoid
device names collisions for same client UUID available
from different MEI heads. Namely this prevents sysfs collision under
/sys/bus/mei/device/
In the device part leave just UUID other parameters that are
required for device matching are not required here and are
just bloating the name.
Cc: <stable@vger.kernel.org> Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Link: https://lore.kernel.org/r/20191105150514.14010-1-tomas.winkler@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This device presents itself as a USB hub with three attached devices:
- An ACM serial port connected to the GPS module (not affected by this
commit)
- An FTDI serial port connected to the GPS module (1546:0502)
- Another FTDI serial port connected to the ODIN-W2 radio module
(1546:0503)
This commit registers U-Blox's VID and the PIDs of the second and third
devices.
Add 024c:0525 to the list of SDIO device-ids, based on a patch found
in the Android X86 kernels. According to that patch this device id is
used on the Alcatel Plus 10 device.
Reported-and-tested-by: youling257 <youling257@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191111113846.24940-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The driver only binds by SDIO device-ids, all the ACPI device-id does
is causing the driver to load unnecessarily on devices where the DSDT
contains a bogus OBDA8723 device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191111113846.24940-2-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The variable skb is released via kfree_skb() when the return value of
_rtl92e_tx is not zero. However, after that, skb is accessed again to
read its length, which may result in a use after free bug. This patch
fixes the bug by moving the release operation to where skb is never
used later.
Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/1572965351-6745-1-git-send-email-bianpan2016@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The regmap update bits call was not selecting the proper mask, considering
the bits which was updating.
Update the mask from call to also include OSCBYPASS.
Removed MOSCEN which was not updated.
Fixes: 1bdf02326b71 ("clk: at91: make use of syscon/regmap internally") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Link: https://lkml.kernel.org/r/1568042692-11784-1-git-send-email-eugen.hristev@microchip.com Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Vlastimil Babka [Fri, 29 Nov 2019 09:03:50 +0000 (10:03 +0100)]
mm, gup: add missing refcount overflow checks on s390
BugLink: https://bugs.launchpad.net/bugs/1855787
The mainline commit 8fde12ca79af ("mm: prevent get_user_pages() from
overflowing page refcount") was backported to 4.14.y stable as commit 04198de24771. The backport however missed that in 4.14, there are several
arch-specific gup.c versions with fast gup implementations, so these do not
prevent refcount overflow.
This stable-only commit fixes the s390 version, and is based on the backport in
SUSE SLES/openSUSE 4.12-based kernels.
The remaining architectures with own gup.c are sparc, mips, sh. It's unlikely
the known overflow scenario based on FUSE, which needs 140GB of RAM, is a
problem for those architectures, and I don't feel confident enough to patch
them.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit 2b6f0090a333 ("mtd: Check add_mtd_device() ret code") contained
a leftover of the debug session that led to this bug fix. Remove this
pr_info().
Fixes: 2b6f0090a333 ("mtd: Check add_mtd_device() ret code") Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently the SMP PHY control execution result is checked, however the
function result for the command is not.
As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.
In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: Jian Luo <luojian5@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The ghes code is careful to parse and round firmware's advertised
memory requirements for CPER records, up to a maximum of 64K.
However when ghes_estatus_pool_expand() does its work, it splits
the requested size into PAGE_SIZE granules.
This means if firmware generates 5K of CPER records, and correctly
describes this in the table, __process_error() will silently fail as it
is unable to allocate more than PAGE_SIZE.
Switch the estatus pool to vmalloc() memory. On x86 vmalloc() memory
may fault and be fixed up by vmalloc_fault(). To prevent this call
vmalloc_sync_all() before an NMI handler could discover the memory.
Signed-off-by: James Morse <james.morse@arm.com> Reviewed-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
oops_begin() exists to group printk() messages with the oops message
printed by die(). To reach this caller we know that platform firmware
took this error first, then notified the OS via NMI with a 'panic'
severity.
Don't wait for another CPU to release the die-lock before panic()ing,
our only goal is to print this fatal error and panic().
This code is always called in_nmi(), and since commit 42a0bb3f7138
("printk/nmi: generic solution for safe printk in NMI"), it has been
safe to call printk() from this context. Messages are batched in a
per-cpu buffer and printed via irq-work, or a call back from panic().
Link: https://patchwork.kernel.org/patch/10313555/ Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
+----------+ +----------+
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SAS disk
|initiator | | |
| device |--- 3.0 G ---| Expander |--- 6.0 G --- SAS disk
| | | |
| |--- 3.0 G ---| |--- 6.0 G --- SATA disk -->failed to connect
| | | |
| | | |--- 6.0 G --- SATA disk -->failed to connect
| | | |
+----------+ +----------+
According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.
Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.
Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.
This patch adds support for checking and rectifying this condition during
initial device discovery only.
We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.
A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.
In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.
This has not caused an issue so far, so leave alone for now.
Tested-by: Jian Luo <luojian5@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Although the apparmorfs dentries are always dropped from the dentry cache
when the usage count drops to zero, there is no guarantee that this will
happen in aafs_remove(), as another thread might still be using it. In
this scenario, this means that the dentry will temporarily continue to
appear in the results of lookups, even after the call to aafs_remove().
In the case of removal of a profile - it also causes simple_rmdir()
on the profile directory to fail, as the directory won't be empty until
the usage counts of all child dentries have decreased to zero. This
results in the dentry for the profile directory leaking and appearing
empty in the file system tree forever.
Signed-off-by: Chris Coulson <chris.coulson@canonical.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
According to firmware error code definition, the error code of 2
means NOT_SUPPORTED, this patch changes it to NOT_SUPPORTED.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In bpf/syscall.c, map_create() first set map->usercnt to 1, a file
descriptor is supposed to return to userspace. When bpf_map_new_fd()
fails, drop the refcount.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID") Signed-off-by: Peng Sun <sironhide0null@gmail.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
debugfs can now report an error code if something went wrong instead of
just NULL. So if the return value is to be used as a "real" dentry, it
needs to be checked if it is an error before dereferencing it.
This is now happening because of ff9fb72bc077 ("debugfs: return error
values, not NULL"). syzbot has found a way to trigger multiple debugfs
files attempting to be created, which fails, and then the error code
gets passed to dentry_path_raw() which obviously does not like it.
Reported-by: Eric Biggers <ebiggers@kernel.org> Reported-and-tested-by: syzbot+7857962b4d45e602b8ad@syzkaller.appspotmail.com Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: kvm@vger.kernel.org Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
1 << 31 is Undefined Behaviour according to the C standard.
Use U type modifier to avoid theoretical overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In bpf/syscall.c, bpf_map_get_fd_by_id() use bpf_map_inc_not_zero()
to increase the refcount, both map->refcnt and map->usercnt. Then, if
bpf_map_new_fd() fails, should handle map->usercnt too.
Fixes: bd5f5f4ecb78 ("bpf: Add BPF_MAP_GET_FD_BY_ID") Signed-off-by: Peng Sun <sironhide0null@gmail.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.
Function sctp_transport_reset_hb_timer has two roles:
- initial start of hb_timer for a given transport,
- update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.
This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.
Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0; //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2; //or more
time_before(hb_timer.expire, new_expire) == false
Fixes: ba6f5e33bdbb ("sctp: avoid refreshing heartbeat timer too often") Reported-by: Marcin Stojek <marcin.stojek@nokia.com> Tested-by: Marcin Stojek <marcin.stojek@nokia.com> Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.
They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bitmap of found partitions in efx_ef10_mtd_probe was not
initialised, causing partitions to be suppressed based off whatever
value was in the bitmap at the start.
Fixes: 3366463513f5 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe") Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When we free skb at tipc_data_input, we return a 'false' boolean.
Then, skb passed to subcalling tipc_link_input in tipc_link_rcv,
<snip>
1303 int tipc_link_rcv:
...
1354 if (!tipc_data_input(l, skb, l->inputq))
1355 rc |= tipc_link_input(l, skb, l->inputq);
</snip>
Fix it by simple changing to a 'true' boolean when skb is being free-ed.
Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above
condition.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <maloy@donjonn.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently, blktrace will not show requests that don't have any data as
rq->__sector is initialized to -1 which is out of device range and thus
discarded by act_log_check(). This is most notably the case for cache
flush requests sent to the device. Fix the problem by making
blk_rq_trace_sector() return 0 for requests without initialized sector.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
To prevent races between smc_lgr_terminate() and smc_conn_free() add an
extra check of the lgr field before accessing it, and cancel a delayed
free_work when a new smc connection is created.
This fixes the problem that free_work cleared the lgr variable but
smc_lgr_terminate() or smc_conn_free() still access it in parallel.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Digging through the ioctls with Al because of the previous
patches, we found that on 64-bit decnet's dn_dev_ioctl()
is wrong, because struct ifreq::ifr_ifru is actually 24
bytes (not 16 as expected from struct sockaddr) due to the
ifru_map and ifru_settings members.
Clearly, decnet expects the ioctl to be called with a struct
like
struct ifreq_dn {
char ifr_name[IFNAMSIZ];
struct sockaddr_dn ifr_addr;
};
since it does
struct ifreq *ifr = ...;
struct sockaddr_dn *sdn = (struct sockaddr_dn *)&ifr->ifr_addr;
This means that DN_IFREQ_SIZE is too big for what it wants on
64-bit, as it is
sizeof(struct ifreq) - sizeof(struct sockaddr) +
sizeof(struct sockaddr_dn)
This assumes that sizeof(struct sockaddr) is the size of ifr_ifru
but that isn't true.
Fix this to use offsetof(struct ifreq, ifr_ifru).
This indeed doesn't really matter much - the result is that we
copy in/out 8 bytes more than we should on 64-bit platforms. In
case the "struct ifreq_dn" lands just on the end of a page though
it might lead to faults.
As far as I can tell, it has been like this forever, so it seems
very likely that nobody cares.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
ip l add dev tun type gretap key 1000
ip a a dev tun 10.0.0.1/24
Packets with tun-id 1000 can be recived by tun dev. But packet can't
be sent through dev tun for non-tunnel-dst
With this patch: tunnel-dst can be get through lwtunnel like beflow:
ip r a 10.0.0.7 encap ip dst 172.168.0.11 dev tun
Signed-off-by: wenxu <wenxu@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Use a bitmap to keep track of which partition types we've already seen;
for duplicates, return -EEXIST from efx_ef10_mtd_probe_partition() and
thus skip adding that partition.
Duplicate partitions occur because of the A/B backup scheme used by newer
sfc NICs. Prior to this patch they cause sysfs_warn_dup errors because
they have the same name, causing us not to expose any MTDs at all.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
On a NOP double buffer update where current buffer address is the same
as the next buffer address, the SDW_UPDATE bit clears too late. As we
are now using this bit to determine when it is safe to signal flip
completion to userspace this will delay completion of atomic commits
where one plane doesn't change the buffer by a whole frame period.
Fix this by remembering the last buffer address and just skip the
double buffer update if it would not change the buffer address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[p.zabel@pengutronix.de: initialize last_bufaddr in ipu_pre_configure] Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This should be 1 for normal allocations, 0 disables leak reporting.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Fixes: 85704cb8dcfd ("net/core/neighbour: tell kmemleak about hash tables") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The API of pci_alloc_irq_vectors_affinity() says it returns -ENOSPC if
fewer than @min_vecs interrupt vectors are available for @dev.
However, if a device supports MSI-X but not MSI and a caller requests
@min_vecs that can't be satisfied by MSI-X, we previously returned -EINVAL
(from the failed attempt to enable MSI), not -ENOSPC.
When -ENOSPC is returned, callers may reduce the number IRQs they request
and try again. Most callers can use the @min_vecs and @max_vecs
parameters to avoid this retry loop, but that doesn't work when using IRQ
affinity "nr_sets" because rebalancing the sets is driver-specific.
This return value bug has been present since pci_alloc_irq_vectors() was
added in v4.10 by aff171641d18 ("PCI: Provide sensible IRQ vector
alloc/free routines"), but it wasn't an issue because @min_vecs/@max_vecs
removed the need for callers to iteratively reduce the number of IRQs
requested and retry the allocation, so they didn't need to distinguish
-ENOSPC from -EINVAL.
In v5.0, 6da4b3ab9a6e ("genirq/affinity: Add support for allocating
interrupt sets") added IRQ sets to the interface, which reintroduced the
need to check for -ENOSPC and possibly reduce the number of IRQs requested
and retry the allocation.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
[bhelgaas: changelog] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Jens Axboe <axboe@fb.com> Cc: Keith Busch <keith.busch@intel.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Addresses-Coverity-ID: 1476406 ("Resource leak") Fixes: 46273cf7e009 ("tipc: fix a missing check of genlmsg_put") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
add_mtd_device() can fail. We should always check its return value
and gracefully handle the failure case. Fix the call sites where this
not done (in mtdpart.c) and add a __must_check attribute to the
prototype to avoid this kind of mistakes.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
lib/genalloc.c: In function 'gen_pool_add_virt':
lib/genalloc.c:190:10: error: implicit declaration of function 'vzalloc_node'; did you mean 'kzalloc_node'?
lib/genalloc.c:190:8: warning: assignment to 'struct gen_pool_chunk *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
lib/genalloc.c: In function 'gen_pool_destroy':
lib/genalloc.c:254:3: error: implicit declaration of function 'vfree'; did you mean 'kfree'?
Fixes: 6862d2fc8185 ('lib/genalloc.c: use vzalloc_node() to allocate the bitmap') Cc: Huang Shijie <sjhuang@iluvatar.ai> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Alexey Skidanov <alexey.skidanov@intel.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
/*
* This memory isn't freed when the device is put,
* I don't have a nice idea for that though. Conceptually
* dma_mask in struct device should not be a pointer.
* See http://thread.gmane.org/gmane.linux.kernel.pci/9081
*/
pdev->dev.dma_mask =
kmalloc(sizeof(*pdev->dev.dma_mask), GFP_KERNEL);
Since this leak has existed for more than 8 years and it does not
reference other parts of the memory, let kmemleak ignore it, so users
don't need to waste time reporting this in the future.
Link: http://lkml.kernel.org/r/20181206160751.36211-1-cai@gmx.us Signed-off-by: Qian Cai <cai@gmx.us> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J . Wysocki" <rafael.j.wysocki@intel.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
kernel/fork.c:167:13: warning: no previous prototype for `arch_release_thread_stack' [-Wmissing-prototypes]
kernel/fork.c:779:13: warning: no previous prototype for `fork_init' [-Wmissing-prototypes]
Add the missing declaration in head file to fix this.
Also, remove arch_release_thread_stack() completely because no arch
seems to implement it since bb9d81264 (arch: remove tile port).
Link: http://lkml.kernel.org/r/1542170087-23645-1-git-send-email-wang.yi59@zte.com.cn Signed-off-by: Yi Wang <wang.yi59@zte.com.cn> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Some devices may have big memory on chip, such as over 1G. In some
cases, the nbytes maybe bigger then 4M which is the bounday of the
memory buddy system (4K default).
So use vzalloc_node() to allocate the bitmap. Also use vfree to free
it.
Link: http://lkml.kernel.org/r/20181225015701.6289-1-sjhuang@iluvatar.ai Signed-off-by: Huang Shijie <sjhuang@iluvatar.ai> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Alexey Skidanov <alexey.skidanov@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
gen_pool_alloc_algo() uses different allocation functions implementing
different allocation algorithms. With gen_pool_first_fit_align()
allocation function, the returned address should be aligned on the
requested boundary.
If chunk start address isn't aligned on the requested boundary, the
returned address isn't aligned too. The only way to get properly
aligned address is to initialize the pool with chunks aligned on the
requested boundary. If want to have an ability to allocate buffers
aligned on different boundaries (for example, 4K, 1MB, ...), the chunk
start address should be aligned on the max possible alignment.
This happens because gen_pool_first_fit_align() looks for properly
aligned memory block without taking into account the chunk start address
alignment.
To fix this, we provide chunk start address to
gen_pool_first_fit_align() and change its implementation such that it
starts looking for properly aligned block with appropriate offset
(exactly as is done in CMA).
Link: https://lkml.kernel.org/lkml/a170cf65-6884-3592-1de9-4c235888cc8a@intel.com Link: http://lkml.kernel.org/r/1541690953-4623-1-git-send-email-alexey.skidanov@intel.com Signed-off-by: Alexey Skidanov <alexey.skidanov@intel.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Daniel Mentz <danielmentz@google.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Laura Abbott <labbott@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit fa5e084e43eb ("vmscan: do not unconditionally treat zones that
fail zone_reclaim() as full") changed the return value of
node_reclaim(). The original return value 0 means NODE_RECLAIM_SOME
after this commit.
While the return value of node_reclaim() when CONFIG_NUMA is n is not
changed. This will leads to call zone_watermark_ok() again.
This patch fixes the return value by adjusting to NODE_RECLAIM_NOSCAN.
Since node_reclaim() is only called in page_alloc.c, move it to
mm/internal.h.
Link: http://lkml.kernel.org/r/20181113080436.22078-1-richard.weiyang@gmail.com Signed-off-by: Wei Yang <richard.weiyang@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Dirty flag of the journal should be cleared at the last stage of umount,
if do it before jbd2_journal_destroy(), then some metadata in uncommitted
transaction could be lost due to io error, but as dirty flag of journal
was already cleared, we can't find that until run a full fsck. This may
cause system panic or other corruption.
Link: http://lkml.kernel.org/r/20181121020023.3034-3-junxiao.bi@oracle.com Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Changwei Ge <ge.changwei@h3c.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@versity.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
genlmsg_put could fail. The fix inserts a check of its return value, and
if it fails, returns -EMSGSIZE.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
atl1e_write_phy_reg() could fail. The fix issues an error message when
it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Both bcm_sf2_sw_indir_rw and mdiobus_write_nested could fail, so let's
return their error codes upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
clk_prepare() could fail, so let's check its status, and if it fails,
return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
clk_prepare() could fail, so let's check its status, and if it fails,
return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If user change inode's i_flags via ioctl, let's add it into global
dirty list, so that checkpoint can guarantee its persistence before
fsync, it can make checkpoint keeping strong consistency.
Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In net_ns_init(), register_pernet_subsys() could fail while registering
network namespace subsystems. The fix checks the return value and
sends a panic() on failure.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In tipc_nl_compat_sk_dump(), if nla_parse_nested() fails, it could return
an error. To be consistent with other invocations of the function call,
on error, the fix passes the return value upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit e39c0df1be5a ("pwm: Introduce the pwm_args concept") has
changed the variable for the period for clps711x-pwm driver, so now
pwm_get/set_period() works with pwm->state.period variable instead
of pwm->args.period.
This patch changes the period variable in other places where it is used.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The following build warnings are seen when building for ARM64 allmodconfig:
drivers/crypto/mxc-scc.c:181:20: warning: format '%d' expects argument of type 'int', but argument 5 has type 'size_t' {aka 'long unsigned int'} [-Wformat=]
drivers/crypto/mxc-scc.c:186:21: warning: format '%d' expects argument of type 'int', but argument 4 has type 'size_t' {aka 'long unsigned int'} [-Wformat=]
drivers/crypto/mxc-scc.c:277:21: warning: format '%d' expects argument of type 'int', but argument 4 has type 'size_t' {aka 'long unsigned int'} [-Wformat=]
drivers/crypto/mxc-scc.c:339:3: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/crypto/mxc-scc.c:340:3: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Fix them by using the %zu specifier to print a size_t variable and using
a plain %x to print the result of a readl().
Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
In update_lmb_associativity_index() we lookup dr_node using
of_find_node_by_path() which takes a reference for us. In the
non-error case we forget to drop the reference. Note that
find_aa_index() does modify properties of the node, but doesn't need
an extra reference held once it's returned.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When the watchdog timer is set in interrupt mode, it causes a
machine check when it times out. The purpose of this mode is to
ease debugging, not to crash the kernel and reboot the machine.
This patch implements a special handling for that, in order to not
crash the kernel if the watchdog times out while in interrupt or
within the idle task.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[scottwood: added missing #include] Signed-off-by: Scott Wood <oss@buserror.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
tps65910_reg_set_bits() may fail. The fix checks if it fails, and if so,
returns with its error code.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
"suspending" IO is overloaded.
It can mean "do not allow new requests" (obviously),
but it also may mean "must not complete pending IO",
for example while the fencing handlers do their arbitration.
When adjusting disk options, we suspend io (disallow new requests), then
wait for the activity-log to become unused (drain all IO completions),
and possibly replace it with a new activity log of different size.
If the other "suspend IO" aspect is active, pending IO completions won't
happen, and we would block forever (unkillable drbdsetup process).
Fix this by skipping the activity log adjustment if the "al-extents"
setting did not change. Also, in case it did change, fail early without
blocking if it looks like we would block forever.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Multiple failure scenario:
a) all good
Connected Primary/Secondary UpToDate/UpToDate
b) lose disk on Primary,
Connected Primary/Secondary Diskless/UpToDate
c) continue to write to the device,
changes only make it to the Secondary storage.
d) lose disk on Secondary,
Connected Primary/Secondary Diskless/Diskless
e) now try to re-attach on Primary
This would have succeeded before, even though that is clearly the
wrong data set to attach to (missing the modifications from c).
Because we only compared our "effective" and the "to-be-attached"
data generation uuid tags if (device->state.conn < C_CONNECTED).
Fix: change that constraint to (device->state.pdsk != D_UP_TO_DATE)
compare the uuids, and reject the attach.
This patch also tries to improve the reverse scenario:
first lose Secondary, then Primary disk,
then try to attach the disk on Secondary.
Before this patch, the attach on the Secondary succeeds, but since commit
drbd: disconnect, if the wrong UUIDs are attached on a connected peer
the Primary will notice unsuitable data, and drop the connection hard.
Though unfortunately at a point in time during the handshake where
we cannot easily abort the attach on the peer without more
refactoring of the handshake.
We now reject any attach to "unsuitable" uuids,
as long as we can see a Primary role,
unless we already have access to "good" data.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
During handshake, if we are diskless ourselves, we used to accept any size
presented by the peer.
Which could be zero if that peer was just brought up and connected
to us without having a disk attached first, in which case both
peers would just "flip" their volume sizes.
Now, even a diskless node will ignore "zero" sizes
presented by a diskless peer.
Also a currently Diskless Primary will refuse to shrink during handshake:
it may be frozen, and waiting for a "suitable" local disk or peer to
re-appear (on-no-data-accessible suspend-io). If the peer is smaller
than what we used to be, it is not suitable.
The logic for a diskless node during handshake is now supposed to be:
believe the peer, if
- I don't have a current size myself
- we agree on the size anyways
- I do have a current size, am Secondary, and he has the only disk
- I do have a current size, am Primary, and he has the only disk,
which is larger than my current size
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The current implementation of the OPAL_PCI_EEH_FREEZE_STATUS call in
skiboot's NPU driver does not touch the pci_error_type parameter so
it might have garbage but the powernv code analyzes it nevertheless.
This initializes pcierr and fstate to zero in all call sites.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As a part of cleanup, the SPAPR TCE IOMMU subdriver releases preregistered
memory. If there is a bug in memory release, the loop in
tce_iommu_release() becomes infinite; this actually happened to me.
This makes the loop finite and prints a warning on every failure to make
the code more bug prone.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bamboo dts has a bug: it uses a non-naturally aligned range
for PCI memory space. This isnt' supported by the code, thus
causing PCI to break on this system.
This is due to the fact that while the chip memory map has 1G
reserved for PCI memory, it's only 512M aligned. The code doesn't
know how to split that into 2 different PMMs and fails, so limit
the region to 512M.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
As several other arches including x86, this patch makes it explicit
that a bad page fault is a NULL pointer dereference when the fault
address is lower than PAGE_SIZE
In the mean time, this page makes all bad_page_fault() messages
shorter so that they remain on one single line. And it prefixes them
by "BUG: " so that they get easily grepped.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Avoid pr_cont()] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch fixes early DEBUG messages in prom.c:
- Use %px instead of %p to see the addresses
- Cast memblock_phys_mem_size() with (unsigned long long) to
avoid build failure when phys_addr_t is not 64 bits.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Raw event code has couple of fields "unit" and "cache" in it, to capture
the "unit" to monitor for a given pmcxsel and cache reload qualifier to
program in MMCR1.
isa207_get_constraint() refers "unit" field to update the MMCRC (L2/L3)
Event bus control fields with "cache" bits of the raw event code.
These are power8 specific and not supported by PowerISA v3.0 pmu. So wrap
the checks to be power8 specific. Also, "cache" bit field is referred to
update MMCR1[16:17] and this check can be power8 specific.
Fixes: 7ffd948fae4cd ('powerpc/perf: factor out power8 pmu functions') Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When ath6kl was reworked to share code between regular and scheduled scans
in commit 3b8ffc6a22ba ("ath6kl: Configure probed SSID list consistently"),
probed SSID entry changed from 1-index to 0-indexed. However,
ath6kl_cfg80211_scan_complete_event() was missed in that change. Fix its
indexing so that we correctly clear out the probed SSID list.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Commit dd45b7598f1c ("ath6kl: Include match ssid list in scheduled scan")
merged the probed and matched SSID lists before sending them to the
firmware. In the process, it assumed match set support is always available
in ath6kl_set_probed_ssids, which breaks scans for hidden SSIDs. Now, check
that the firmware supports matching SSIDs in scheduled scans before setting
MATCH_SSID_FLAG.
Fixes: dd45b7598f1c ("ath6kl: Include match ssid list in scheduled scan") Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The intent of invoking configfs_depend_item in commit 7474f52a82d51
("tcm_qla2xxx: Perform configfs depend/undepend for base_tpg")
was to prevent a physical Fibre Channel port removal when
virtual (NPIV) ports announced through that physical port are active.
The change does not work as expected: it makes enabled physical port
dependent on target configfs subsystem (the port's parent), something
the configfs guarantees anyway.
Besides, scheduling work in a worker thread and waiting for the work's
completion is not really a valid workaround for the requirement not to call
configfs_depend_item from a configfs callback: the call occasionally
deadlocks.
Thus, removing configfs_depend_item calls does not break anything and fixes
the deadlock problem.
Signed-off-by: Anatoliy Glagolev <glagolig@gmail.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
This patch avoids that the SCSI mid-layer keeps retrying forever if
ib_post_send() fails. This was discovered while testing immediate
data support and passing a too large num_sge value to ib_post_send().
Cc: Sergey Gorenko <sergeygo@mellanox.com> Cc: Max Gurtovoy <maxg@mellanox.com> Cc: Laurence Oberman <loberman@redhat.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Function max310x_tx_empty() accesses the IRQSTS register, which is
cleared by IC when reading, so if there is an interrupt status, we
will lose it. This patch implement the transmitter check only by
the current FIFO level.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The Broadcom controller on aries S5PV210 boards sends out a couple of
unknown packets after the firmware is loaded. This will cause
logging of errors such as:
Bluetooth: hci0: Frame reassembly failed (-84)
This is probably also the case with other boards, as there are related
Android userspace patches for custom ROMs such as
https://review.lineageos.org/#/c/LineageOS/android_system_bt/+/142721/
Since this appears to be intended behaviour, treated them as diagnostic
packets.
Note that this is another variant of commit 01d5e44ace8a
("Bluetooth: hci_bcm: Handle empty packet after firmware loading")
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If palmas_smps_read() fails, we should not use the read data in "reg"
which may contain random value. The fix inserts a check for the return
value of palmas_smps_read(): If it fails, we return the error code
upstream and stop using "reg".
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
When a failure occurs in rtnl_configure_link(), the current code
calls unregister_netdevice() to roll back the earlier call to
register_netdevice(), and jumps to errout, which calls
vxlan_fdb_destroy().
However unregister_netdevice() calls transitively ndo_uninit, which is
vxlan_uninit(), and that already takes care of deleting the default FDB
entry by calling vxlan_fdb_delete_default(). Since the entry added
earlier in __vxlan_dev_create() is exactly the default entry, the
cleanup code in the errout block always leads to double free and thus a
panic.
Besides, since vxlan_fdb_delete_default() always destroys the FDB entry
with notification enabled, the deletion of the default entry is notified
even before the addition was notified.
Instead, move the unregister_netdevice() call after the manual destroy,
which solves both problems.
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
TIMER_INTR_MASK register (Base Address of Timer + 0x38) is not designed
for masking interrupts on ast2500 chips, and it's not even listed in
ast2400 datasheet, so it's not safe to access TIMER_INTR_MASK on aspeed
chips.
Similarly, TIMER_INTR_STATE register (Base Address of Timer + 0x34) is
not interrupt status register on ast2400 and ast2500 chips. Although
there is no side effect to reset the register in fttmr010_common_init(),
it's just misleading to do so.
Besides, "count_down" is renamed to "is_aspeed" in "fttmr010" structure,
and more comments are added so the code is more readble.
Signed-off-by: Tao Ren <taoren@fb.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The bulkstat family of ioctls are problematic on x32, because there is
a mixup of native 32-bit and 64-bit conventions. The xfs_fsop_bulkreq
struct contains pointers and 32-bit integers so that matches the native
32-bit layout, and that means the ioctl implementation goes into the
regular compat path on x32.
However, the 'ubuffer' member of that struct in turn refers to either
struct xfs_inogrp or xfs_bstat (or an array of these). On x32, those
structures match the native 64-bit layout. The compat implementation
writes out the 32-bit version of these structures. This is not the
expected format for x32 userspace, causing problems.
Fortunately the functions which actually output these xfs_inogrp and
xfs_bstat structures have an easy way to select which output format
is required, so we just need a little tweak to select the right format
on x32.
Signed-off-by: Nick Bowler <nbowler@draconx.ca> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
While inspecting the ioctl implementations, I noticed that the compat
implementation of XFS_IOC_ATTRLIST_BY_HANDLE does not do exactly the
same thing as the native implementation. Specifically, the "cursor"
does not appear to be written out to userspace on the compat path,
like it is on the native path.
This adjusts the compat implementation to copy out the cursor just
like the native implementation does. The attrlist cursor does not
require any special compat handling. This fixes xfstests xfs/269
on both IA-32 and x32 userspace, when running on an amd64 kernel.
Signed-off-by: Nick Bowler <nbowler@draconx.ca> Fixes: 0facef7fb053b ("xfs: in _attrlist_by_handle, copy the cursor back to userspace") Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Before this patch, function do_grow would not reserve enough journal
blocks in the transaction to unstuff jdata files while growing them.
This patch adds the logic to add one more block if the file to grow
is jdata.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The flakey target is documented to be able to corrupt the Nth byte in
a bio, but does not corrupt byte indices after the first biovec in the
bio. Change the corrupting function to actually corrupt the Nth byte
no matter in which biovec that index falls.
A test device generating two-page bios, atop a flakey device configured
to corrupt a byte index on the second page, verified both the failure
to corrupt before this patch and the expected corruption after this
change.
Signed-off-by: John Dorminy <jdorminy@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.
Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].
Fixes: ac1ebc2190f575fc ("sh-pfc: Add sh7734 pinmux support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.
The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.
Fixes: a8d42fc4217b1ea1 ("sh-pfc: Add sh7264 pinmux support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
With autoneg enabled, PHY loopback test fails. To disable autoneg,
driver needs to send a valid forced speed to FW. FW is not sending
async event for invalid speeds. To fix this, query forced speeds
and send the correct speed when disabling autoneg mode.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Currently firmware specific errors are returned directly in flash_device
and reset ethtool hooks. Modify it to return linux standard errors
to userspace when flashing operations fail.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
The failure to create debugfs entry is unpleasant event, but not enough
to abort drier initialization. Align the mlx5_core code to debugfs design
and continue execution whenever debugfs_create_dir() successes or not.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
samples/vfio-mdev/mtty.c:592:39: warning: implicit conversion from 'int'
to 'char' changes value from 162 to -94 [-Wconstant-conversion]
*buf = UART_MSR_DSR | UART_MSR_DDSR | UART_MSR_DCD;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
1 warning generated.
Turns out that all uses of buf in this function ultimately end up stored
or cast to an unsigned type. Just use u8, which has the same number of
bits but can store this larger number so Clang no longer warns.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
If pcistub_init_device fails, the release function will be called with
dev_data set to NULL. Check it before using it to avoid a NULL pointer
dereference.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>