Dan Moulding [Tue, 24 Mar 2020 23:55:45 +0000 (16:55 -0700)]
iwlwifi: mvm: Do not require PHY_SKU NVM section for 3168 devices
BugLink: https://bugs.launchpad.net/bugs/1868442
The logic for checking required NVM sections was recently fixed in
commit b3f20e098293 ("iwlwifi: mvm: fix NVM check for 3168
devices"). However, with that fixed the else is now taken for 3168
devices and within the else clause there is a mandatory check for the
PHY_SKU section. This causes the parsing to fail for 3168 devices.
The PHY_SKU section is really only mandatory for the IWL_NVM_EXT
layout (the phy_sku parameter of iwl_parse_nvm_data is only used when
the NVM type is IWL_NVM_EXT). So this changes the PHY_SKU section
check so that it's only mandatory for IWL_NVM_EXT.
Fixes: b3f20e098293 ("iwlwifi: mvm: fix NVM check for 3168 devices") Signed-off-by: Dan Moulding <dmoulding@me.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
(cherry picked from commit a9149d243f259ad8f02b1e23dfe8ba06128f15e1) Signed-off-by: Sultan Alsawaf <sultan.alsawaf@canonical.com> Acked-by: Khalid Elmously <khalid.elmously@canonical.com> Acked-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Jan Kara [Tue, 24 Mar 2020 09:19:00 +0000 (10:19 +0100)]
ext4: fix mount failure with quota configured as module
BugLink: https://bugs.launchpad.net/bugs/1868665
When CONFIG_QFMT_V2 is configured as a module, the test in
ext4_feature_set_ok() fails and so mount of filesystems with quota or
project features fails. Fix the test to use IS_ENABLED macro which
works properly even for modules.
Link: https://lore.kernel.org/r/20200221100835.9332-1-jack@suse.cz Fixes: d65d87a07476 ("ext4: improve explanation of a mount failure caused by a misconfigured kernel") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org
(cherry picked from commit 9db176bceb5c5df4990486709da386edadc6bd1d) Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Acked-by: Andrea Righi <andrea.righi@canonical.com> Acked-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1865402
ODM asks us to use get_display_mode command to confirm the scalar's
behavior, and Windows use this command, too.
To align the behavior with Windows, remove get_scalar_status command and
replace it with get_display_mode.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com> Acked-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Define PT_MAX_FULL_LEVELS as PT64_ROOT_MAX_LEVEL, i.e. 5, to fix shadow
paging for 5-level guest page tables. PT_MAX_FULL_LEVELS is used to
size the arrays that track guest pages table information, i.e. using a
"max levels" of 4 causes KVM to access garbage beyond the end of an
array when querying state for level 5 entries. E.g. FNAME(gpte_changed)
will read garbage and most likely return %true for a level 5 entry,
soft-hanging the guest because FNAME(fetch) will restart the guest
instead of creating SPTEs because it thinks the guest PTE has changed.
Note, KVM doesn't yet support 5-level nested EPT, so PT_MAX_FULL_LEVELS
gets to stay "4" for the PTTYPE_EPT case.
Commit 904cdbd41d74 ("jbd2: clear dirty flag when revoking a buffer from
an older transaction") set the BH_Freed flag when forgetting a metadata
buffer which belongs to the committing transaction, it indicate the
committing process clear dirty bits when it is done with the buffer. But
it also clear the BH_Mapped flag at the same time, which may trigger
below NULL pointer oops when block_size < PAGE_SIZE.
*) Dir entry block bh1 and bh2 belongs to one page, and the bh2 has
already been unmapped.
For the metadata buffer we forgetting, we should always keep the mapped
flag and clear the dirty flags is enough, so this patch pick out the
these buffers and keep their BH_Mapped flag.
Link: https://lore.kernel.org/r/20200213063821.30455-3-yi.zhang@huawei.com Fixes: 904cdbd41d74 ("jbd2: clear dirty flag when revoking a buffer from an older transaction") Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There is no need to delay the clearing of b_modified flag to the
transaction committing time when unmapping the journalled buffer, so
just move it to the journal_unmap_buffer().
Link: https://lore.kernel.org/r/20200213063821.30455-2-yi.zhang@huawei.com Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.
Signed-off-by: Mike Jones <michael-a1.jones@analog.com> Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com Fixes: e04d1ce9bbb49 ("hwmon: (ltc2978) Add polling for chips requiring it") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Perf doesn't take the left period into account when auto-reload is
enabled with fixed period sampling mode in context switch.
Here is the MSR trace of the perf command as below.
(The MSR trace is simplified from a ftrace log.)
#perf record -e cycles:p -c 2000000 -- ./triad_loop
//The MSR trace of task schedule out
//perf disable all counters, disable PEBS, disable GP counter 0,
//read GP counter 0, and re-enable all counters.
//The counter 0 stops at 0xfffffff82840
write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0
write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 0
write_msr: MSR_P6_EVNTSEL0(186), value 40003003c
rdpmc: 0, value fffffff82840
write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff
//The MSR trace of the same task schedule in again
//perf disable all counters, enable and set GP counter 0,
//enable PEBS, and re-enable all counters.
//0xffffffe17b80 (-2000000) is written to GP counter 0.
write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0
write_msr: MSR_IA32_PMC0(4c1), value ffffffe17b80
write_msr: MSR_P6_EVNTSEL0(186), value 40043003c
write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 1
write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff
When the same task schedule in again, the counter should starts from
previous left. However, it starts from the fixed period -2000000 again.
A special variant of intel_pmu_save_and_restart() is used for
auto-reload, which doesn't update the hwc->period_left.
When the monitored task schedules in again, perf doesn't know the left
period. The fixed period is used, which is inaccurate.
With auto-reload, the counter always has a negative counter value. So
the left period is -value. Update the period_left in
intel_pmu_save_and_restart_reload().
With the patch:
//The MSR trace of task schedule out
write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0
write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 0
write_msr: MSR_P6_EVNTSEL0(186), value 40003003c
rdpmc: 0, value ffffffe25cbc
write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff
//The MSR trace of the same task schedule in again
write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0
write_msr: MSR_IA32_PMC0(4c1), value ffffffe25cbc
write_msr: MSR_P6_EVNTSEL0(186), value 40043003c
write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 1
write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff
Fixes: d31fc13fdcb2 ("perf/x86/intel: Fix event update for auto-reload") Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lkml.kernel.org/r/20200121190125.3389-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In file included from ../arch/s390/boot/startup.c:3:
In file included from ../include/linux/elf.h:5:
In file included from ../arch/s390/include/asm/elf.h:132:
In file included from ../include/linux/compat.h:10:
In file included from ../include/linux/time.h:74:
In file included from ../include/linux/time32.h:13:
In file included from ../include/linux/timex.h:65:
../arch/s390/include/asm/timex.h:160:20: warning: passing 'unsigned char
[16]' to parameter of type 'char *' converts between pointers to integer
types with different sign [-Wpointer-sign]
get_tod_clock_ext(clk);
^~~
../arch/s390/include/asm/timex.h:149:44: note: passing argument to
parameter 'clk' here
static inline void get_tod_clock_ext(char *clk)
^
Change clk's type to just be char so that it matches what happens in
get_tod_clock_ext.
We don't need to set pkey as valid in case that user set only one of pkey
index or port number, otherwise it will be resulted in NULL pointer
dereference while accessing to uninitialized pkey list. The following
crash from Syzkaller revealed it.
The root cause is that tasklet is actually a softirq. In a tasklet
handler, another softirq handler is triggered. Usually these softirq
handlers run on the same cpu core. So this will cause "soft lockup Bug".
Fixes: 8700e3e7c485 ("Soft RoCE driver") Link: https://lore.kernel.org/r/20200212072635.682689-8-leon@kernel.org Signed-off-by: Zhu Yanjun <yanjunz@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When the hfi1 device is shut down during a system reboot, it is possible
that some QPs might have not not freed by ULPs. More requests could be
post sent and a lingering timer could be triggered to schedule more packet
sends, leading to a crash:
The solution is to reset the QPs before the device resources are freed.
This reset will change the QP state to prevent post sends and delete
timers to prevent callbacks.
Fixes: 0acb0cc7ecc1 ("IB/rdmavt: Initialize and teardown of qpn table") Link: https://lore.kernel.org/r/20200210131040.87408.38161.stgit@awfm-01.aw.intel.com Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The panic is the result of slab entries being freed during the destruction
of the pq slab.
The code attempts to quiesce the pq, but looking for n_req == 0 doesn't
account for new requests.
Fix the issue by using SRCU to get a pq pointer and adjust the pq free
logic to NULL the fd pq pointer prior to the quiesce.
Fixes: e87473bc1b6c ("IB/hfi1: Only set fd pointer when base context is completely initialized") Link: https://lore.kernel.org/r/20200210131033.87408.81174.stgit@awfm-01.aw.intel.com Reviewed-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit 3fe3331bb285 ("perf/x86/amd: Add event map for AMD Family 17h"),
claimed L2 misses were unsupported, due to them not being found in its
referenced documentation, whose link has now moved [1].
That old documentation listed PMCx064 unit mask bit 3 as:
"LsRdBlkC: LS Read Block C S L X Change to X Miss."
and bit 0 as:
"IcFillMiss: IC Fill Miss"
We now have new public documentation [2] with improved descriptions, that
clearly indicate what events those unit mask bits represent:
Bit 3 now clearly states:
"LsRdBlkC: Data Cache Req Miss in L2 (all types)"
and bit 0 is:
"IcFillMiss: Instruction Cache Req Miss in L2."
So we can now add support for L2 misses in perf's genericised events as
PMCx064 with both the above unit masks.
[1] The commit's original documentation reference, "Processor Programming
Reference (PPR) for AMD Family 17h Model 01h, Revision B1 Processors",
originally available here:
When all CPUs in the system implement the SSBS extension, the SSBS field
in PSTATE is the definitive indication of the mitigation state. Further,
when the CPUs implement the SSBS manipulation instructions (advertised
to userspace via an HWCAP), EL0 can toggle the SSBS field directly and
so we cannot rely on any shadow state such as TIF_SSBD at all.
Avoid forcing the SSBS field in context-switch on such a system, and
simply rely on the PSTATE register instead.
Cc: <stable@vger.kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Srinivas Ramana <sramana@codeaurora.org> Fixes: cbdf8a189a66 ("arm64: Force SSBS on context switch") Reviewed-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A remount to a read-write filesystem is not safe when there's tree-log
to be replayed. Files that could be opened until now might be affected
by the changes in the tree-log.
A regular mount is needed to replay the log so the filesystem presents
the consistent view with the pending changes included.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
There's no logged information about tree-log replay although this is
something that points to previous unclean unmount. Other filesystems
report that as well.
Suggested-by: Chris Murphy <lists@colorremedies.com> CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
In btrfs_ref_tree_mod(), 'ref' and 'ra' are allocated through kzalloc() and
kmalloc(), respectively. In the following code, if an error occurs, the
execution will be redirected to 'out' or 'out_unlock' and the function will
be exited. However, on some of the paths, 'ref' and 'ra' are not
deallocated, leading to memory leaks. For example, if 'action' is
BTRFS_ADD_DELAYED_EXTENT, add_block_entry() will be invoked. If the return
value indicates an error, the execution will be redirected to 'out'. But,
'ref' is not deallocated on this path, causing a memory leak.
To fix the above issues, deallocate both 'ref' and 'ra' before exiting from
the function when an error is encountered.
CC: stable@vger.kernel.org # 4.15+ Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
We have a few cases where we allow an extent map that is in an extent map
tree to be merged with other extents in the tree. Such cases include the
unpinning of an extent after the respective ordered extent completed or
after logging an extent during a fast fsync. This can lead to subtle and
dangerous problems because when doing the merge some other task might be
using the same extent map and as consequence see an inconsistent state of
the extent map - for example sees the new length but has seen the old start
offset.
With luck this triggers a BUG_ON(), and not some silent bug, such as the
following one in __do_readpage():
$ cat -n fs/btrfs/extent_io.c
3061 static int __do_readpage(struct extent_io_tree *tree,
3062 struct page *page,
(...)
3127 em = __get_extent_map(inode, page, pg_offset, cur,
3128 end - cur + 1, get_extent, em_cached);
3129 if (IS_ERR_OR_NULL(em)) {
3130 SetPageError(page);
3131 unlock_extent(tree, cur, end);
3132 break;
3133 }
3134 extent_offset = cur - em->start;
3135 BUG_ON(extent_map_end(em) <= cur);
(...)
Consider the following example scenario, where we end up hitting the
BUG_ON() in __do_readpage().
We have an inode with a size of 8KiB and 2 extent maps:
extent A: file offset 0, length 4KiB, disk_bytenr = X, persisted on disk by
a previous transaction
extent B: file offset 4KiB, length 4KiB, disk_bytenr = X + 4KiB, not yet
persisted but writeback started for it already. The extent map
is pinned since there's writeback and an ordered extent in
progress, so it can not be merged with extent map A yet
The following sequence of steps leads to the BUG_ON():
1) The ordered extent for extent B completes, the respective page gets its
writeback bit cleared and the extent map is unpinned, at that point it
is not yet merged with extent map A because it's in the list of modified
extents;
2) Due to memory pressure, or some other reason, the MM subsystem releases
the page corresponding to extent B - btrfs_releasepage() is called and
returns 1, meaning the page can be released as it's not dirty, not under
writeback anymore and the extent range is not locked in the inode's
iotree. However the extent map is not released, either because we are
not in a context that allows memory allocations to block or because the
inode's size is smaller than 16MiB - in this case our inode has a size
of 8KiB;
3) Task B needs to read extent B and ends up __do_readpage() through the
btrfs_readpage() callback. At __do_readpage() it gets a reference to
extent map B;
4) Task A, doing a fast fsync, calls clear_em_loggin() against extent map B
while holding the write lock on the inode's extent map tree - this
results in try_merge_map() being called and since it's possible to merge
extent map B with extent map A now (the extent map B was removed from
the list of modified extents), the merging begins - it sets extent map
B's start offset to 0 (was 4KiB), but before it increments the map's
length to 8KiB (4kb + 4KiB), task A is at:
BUG_ON(extent_map_end(em) <= cur);
The call to extent_map_end() sees the extent map has a start of 0
and a length still at 4KiB, so it returns 4KiB and 'cur' is 4KiB, so
the BUG_ON() is triggered.
So it's dangerous to modify an extent map that is in the tree, because some
other task might have got a reference to it before and still using it, and
needs to see a consistent map while using it. Generally this is very rare
since most paths that lookup and use extent maps also have the file range
locked in the inode's iotree. The fsync path is pretty much the only
exception where we don't do it to avoid serialization with concurrent
reads.
Fix this by not allowing an extent map do be merged if if it's being used
by tasks other then the one attempting to merge the extent map (when the
reference count of the extent map is greater than 2).
Reported-by: ryusuke1925 <st13s20@gm.ibaraki-ct.ac.jp> Reported-by: Koki Mitani <koki.mitani.xg@hco.ntt.co.jp>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206211 CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
If CONFIG_QFMT_V2 is not enabled, but CONFIG_QUOTA is enabled, when a
user tries to mount a file system with the quota or project quota
enabled, the kernel will emit a very confusing messsage:
EXT4-fs warning (device vdc): ext4_enable_quotas:5914: Failed to enable quota tracking (type=0, err=-3). Please run e2fsck to fix.
EXT4-fs (vdc): mount failed
We will now report an explanatory message indicating which kernel
configuration options have to be enabled, to avoid customer/sysadmin
confusion.
Link: https://lore.kernel.org/r/20200215012738.565735-1-tytso@mit.edu
Google-Bug-Id: 149093531 Fixes: 7c319d328505b778 ("ext4: make quota as first class supported feature") Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
When journal size is set too big by "mkfs.ext4 -J size=", or when
we mount a crafted image to make journal inode->i_size too big,
the loop, "while (i < num)", holds cpu too long. This could cause
soft lockup.
DIR_INDEX has been introduced as a compat ext4 feature. That means that
even kernels / tools that don't understand the feature may modify the
filesystem. This works because for kernels not understanding indexed dir
format, internal htree nodes appear just as empty directory entries.
Index dir aware kernels then check the htree structure is still
consistent before using the data. This all worked reasonably well until
metadata checksums were introduced. The problem is that these
effectively made DIR_INDEX only ro-compatible because internal htree
nodes store checksums in a different place than normal directory blocks.
Thus any modification ignorant to DIR_INDEX (or just clearing
EXT4_INDEX_FL from the inode) will effectively cause checksum mismatch
and trigger kernel errors. So we have to be more careful when dealing
with indexed directories on filesystems with checksumming enabled.
1) We just disallow loading any directory inodes with EXT4_INDEX_FL when
DIR_INDEX is not enabled. This is harsh but it should be very rare (it
means someone disabled DIR_INDEX on existing filesystem and didn't run
e2fsck), e2fsck can fix the problem, and we don't want to answer the
difficult question: "Should we rather corrupt the directory more or
should we ignore that DIR_INDEX feature is not set?"
2) When we find out htree structure is corrupted (but the filesystem and
the directory should in support htrees), we continue just ignoring htree
information for reading but we refuse to add new entries to the
directory to avoid corrupting it more.
Link: https://lore.kernel.org/r/20200210144316.22081-1-jack@suse.cz Fixes: dbe89444042a ("ext4: Calculate and verify checksums for htree nodes") Reviewed-by: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A recent commit, 9803387c55f7 ("ext4: validate the
debug_want_extra_isize mount option at parse time"), moved mount-time
checks around. One of those changes moved the inode size check before
the blocksize variable was set to the blocksize of the file system.
After 9803387c55f7 was set to the minimum allowable blocksize, which
in practice on most systems would be 1024 bytes. This cuased file
systems with inode sizes larger than 1024 bytes to be rejected with a
message:
EXT4-fs (sdXX): unsupported inode size: 4096
Fixes: 9803387c55f7 ("ext4: validate the debug_want_extra_isize mount option at parse time") Link: https://lore.kernel.org/r/20200206225252.GA3673@mit.edu Reported-by: Herbert Poetzl <herbert@13thfloor.at> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Don't assume that the mmp_nodename and mmp_bdevname strings are NUL
terminated, since they are filled in by snprintf(), which is not
guaranteed to do so.
We set the compat_elf_hwcap bits unconditionally on arm64 to
include the VFP and NEON support. However, the FP/SIMD unit
is optional on Arm v8 and thus could be missing. We already
handle this properly in the kernel, but still advertise to
the COMPAT applications that the VFP is available. Fix this
to make sure we only advertise when we really have them.
Cc: stable@vger.kernel.org # v4.19 Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The Audioengine D1 (0x2912:0x30c8) does support reading the sample rate,
but it returns the rate in byte-reversed order.
When setting sampling rate, the driver produces these warning messages:
[168840.944226] usb 3-2.2: current rate 4500480 is different from the runtime rate 44100
[168854.930414] usb 3-2.2: current rate 8436480 is different from the runtime rate 48000
[168905.185825] usb 3-2.1.2: current rate 30465 is different from the runtime rate 96000
As can be seen from the hexadecimal conversion, the current rate read
back is byte-reversed from the rate that was set.
MSI-GL73 laptop with ALC1220 codec requires a similar workaround for
Clevo laptops to enforce the DAC/mixer connection path. Set up a
quirk entry for that.
../drivers/mtd/nand/onenand/onenand_base.c:1269:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
while (!ret) {
^
../drivers/mtd/nand/onenand/onenand_base.c:1266:2: note: previous
statement is here
if (column + thislen > writesize)
^
1 warning generated.
This warning occurs because there is a space before the tab of the while
loop. There are spaces at the beginning of a lot of the lines in this
block, remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
KVM's inject_abt64() injects an external-abort into an aarch64 guest.
The KVM_CAP_ARM_INJECT_EXT_DABT is intended to do exactly this, but
for an aarch32 guest inject_abt32() injects an implementation-defined
exception, 'Lockdown fault'.
Change this to external abort. For non-LPAE we now get the documented:
| Unhandled fault: external abort on non-linefetch (0x008) at 0x9c800f00
and for LPAE:
| Unhandled fault: synchronous external abort (0x210) at 0x9c800f00
Beata reports that KVM_SET_VCPU_EVENTS doesn't inject the expected
exception to a non-LPAE aarch32 guest.
The host intends to inject DFSR.FS=0x14 "IMPLEMENTATION DEFINED fault
(Lockdown fault)", but the guest receives DFSR.FS=0x04 "Fault on
instruction cache maintenance". This fault is hooked by
do_translation_fault() since ARMv6, which goes on to silently 'handle'
the exception, and restart the faulting instruction.
It turns out, when TTBCR.EAE is clear DFSR is split, and FS[4] has
to shuffle up to DFSR[10].
As KVM only does this in one place, fix up the static values. We
now get the expected:
| Unhandled fault: lock abort (0x404) at 0x9c800f00
This should not be using ib_dev to test for disassociation, during
disassociation is_closed is set under lock and the waitq is triggered.
Instead check is_closed and be sure to re-obtain the lock to test the
value after the wait_event returns.
Fixes: 036b10635739 ("IB/uverbs: Enable device removal when there are active user space applications") Link: https://lore.kernel.org/r/1578504126-9400-12-git-send-email-yishaih@mellanox.com Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.
- Write address low 32bits
- Write address high 32bits (If supported by device)
- Write data
When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.
On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.
Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:
If MSI is disabled the PCI device is routing an interrupt to the legacy
INTx mechanism. The INTx delivery can be disabled, but the disablement is
not working on all devices.
Some devices lose interrupts when both MSI and INTx delivery are disabled.
Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.
Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.
That makes it possible to solve it with a two step update:
1) Target the MSI msg to the new vector on the current target CPU
2) Target the MSI msg to the new vector on the new target CPU
In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.
After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.
This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.
This can cause spurious interrupts on both the local and the new target
CPU.
1) If the new vector is not in use on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then interrupt entry code will
ignore that spurious interrupt. The vector is marked so that the
'No irq handler for vector' warning is supressed once.
2) If the new vector is in use already on the local CPU then the IRR check
might see an pending interrupt from the device which is using this
vector. The IPI to the new target CPU will then invoke the handler of
the device, which got the affinity change, even if that device did not
issue an interrupt
3) If the new vector is in use already on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then the handler of the device which
uses that vector on the local CPU will be invoked.
expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: Evan Green <evgreen@chromium.org> Debugged-by: Evan Green <evgreen@chromium.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Evan Green <evgreen@chromium.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Convert a plethora of parameters and variables in the MMU and page fault
flows from type gva_t to gpa_t to properly handle TDP on 32-bit KVM.
Thanks to PSE and PAE paging, 32-bit kernels can access 64-bit physical
addresses. When TDP is enabled, the fault address is a guest physical
address and thus can be a 64-bit value, even when both KVM and its guest
are using 32-bit virtual addressing, e.g. VMX's VMCS.GUEST_PHYSICAL is a
64-bit field, not a natural width field.
Using a gva_t for the fault address means KVM will incorrectly drop the
upper 32-bits of the GPA. Ditto for gva_to_gpa() when it is used to
translate L2 GPAs to L1 GPAs.
Opportunistically rename variables and parameters to better reflect the
dual address modes, e.g. use "cr2_or_gpa" for fault addresses and plain
"addr" instead of "vaddr" when the address may be either a GVA or an L2
GPA. Similarly, use "gpa" in the nonpaging_page_fault() flows to avoid
a confusing "gpa_t gva" declaration; this also sets the stage for a
future patch to combing nonpaging_page_fault() and tdp_page_fault() with
minimal churn.
Sprinkle in a few comments to document flows where an address is known
to be a GVA and thus can be safely truncated to a 32-bit value. Add
WARNs in kvm_handle_page_fault() and FNAME(gva_to_gpa_nested)() to help
document such cases and detect bugs.
Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
This patch is trying to address the issue observed when hotplug DP
daisy chain monitors.
e.g.
src-mstb-mstb-sst -> src (unplug) mstb-mstb-sst -> src-mstb-mstb-sst
(plug in again)
Once unplug a DP MST capable device, driver will call
drm_dp_mst_topology_mgr_set_mst() to disable MST. In this function,
it cleans data of topology manager while disabling mst_state. However,
it doesn't clean up the proposed_vcpis of topology manager.
If proposed_vcpi is not reset, once plug in MST daisy chain monitors
later, code will fail at checking port validation while trying to
allocate payloads.
When MST capable device is plugged in again and try to allocate
payloads by calling drm_dp_update_payload_part1(), this
function will iterate over all proposed virtual channels to see if
any proposed VCPI's num_slots is greater than 0. If any proposed
VCPI's num_slots is greater than 0 and the port which the
specific virtual channel directed to is not in the topology, code then
fails at the port validation. Since there are stale VCPI allocations
from the previous topology enablement in proposed_vcpi[], code will fail
at port validation and reurn EINVAL.
[How]
Clean up the data of stale proposed_vcpi[] and reset mgr->proposed_vcpis
to NULL while disabling mst in drm_dp_mst_topology_mgr_set_mst().
Changes since v1:
*Add on more details in commit message to describe the issue which the
patch is trying to fix
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
[added cc to stable] Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191205090043.7580-1-Wayne.Lin@amd.com Cc: <stable@vger.kernel.org> # v3.17+ Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
b53_configure_vlan() is called by the bcm_sf2 driver upon setup and
indirectly through resume as well. During the initial setup, we are
guaranteed that dev->vlan_enabled is false, so there is no change in
behavior, however during suspend, we may have enabled VLANs before, so we
do want to restore that setting.
Fixes: dad8d7c6452b ("net: dsa: b53: Properly account for VLAN filtering") Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
../drivers/gpu/drm/msm/disp/mdp4/mdp4_dsi_encoder.c:124:3: warning:
misleading indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
mdp4_crtc_set_config(encoder->crtc,
^
../drivers/gpu/drm/msm/disp/mdp4/mdp4_dsi_encoder.c:121:2: note:
previous statement is here
if (mdp4_dsi_encoder->enabled)
^
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: 776638e73a19 ("drm/msm/dsi: Add a mdp4 encoder for DSI") Link: https://github.com/ClangBuiltLinux/linux/issues/792 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
CONFIG_VIRTUALIZATION may not be enabled for memory encrypted guests. If
disabled, decrypted per-CPU variables may end up sharing the same page
with variables that should be left encrypted.
Always separate per-CPU variables that should be decrypted into their own
page anytime memory encryption can be enabled in the guest rather than
rely on any other config option that may not be enabled.
Disabling a display on MST can potentially happen after the entire MST
topology has been removed, which means that we can't communicate with
the topology at all in this scenario. Likewise, this also means that we
can't properly update payloads on the topology and as such, it's a good
idea to ignore payload update failures when disabling displays.
Currently, amdgpu makes the mistake of halting the payload update
process when any payload update failures occur, resulting in leaving
DC's local copies of the payload tables out of date.
This ends up causing problems with hotplugging MST topologies, and
causes modesets on the second hotplug to fail like so:
Note as well, I have only been able to reproduce this on setups with 2
MST displays.
Changes since v1:
* Don't return false when part 1 or part 2 of updating the payloads
fails, we don't want to abort at any step of the process even if
things fail
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
eventfd use cases from aio and io_uring can deadlock due to circular
or resursive calling, when eventfd_signal() tries to grab the waitqueue
lock. On top of that, it's also possible to construct notification
chains that are deep enough that we could blow the stack.
Add a percpu counter that tracks the percpu recursion depth, warn if we
exceed it. The counter is also exposed so that users of eventfd_signal()
can do the right thing if it's non-zero in the context where it is
called.
In year 2007 high performance SSD was still expensive, in order to
save more space for real workload or meta data, the readahead I/Os
for non-meta data was bypassed and not cached on SSD.
In now days, SSD price drops a lot and people can find larger size
SSD with more comfortable price. It is unncessary to alway bypass
normal readahead I/Os to save SSD space for now.
This patch adds options for readahead data cache policies via sysfs
file /sys/block/bcache<N>/readahead_cache_policy, the options are,
- "all": cache all readahead data I/Os.
- "meta-only": only cache meta data, and bypass other regular I/Os.
If users want to make bcache continue to only cache readahead request
for metadata and bypass regular data readahead, please set "meta-only"
to this sysfs file. By default, bcache will back to cache all read-
ahead requests now.
Cc: stable@vger.kernel.org Signed-off-by: Coly Li <colyli@suse.de> Acked-by: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
After the commit 44ea39420fc9 ("drivers/watchdog: make use of
devm_register_reboot_notifier()") the struct notifier_block reboot_nb in
the struct watchdog_device is removed from the reboot notifiers chain at
the time watchdog's chardev is closed. But at least in i6300esb.c case
reboot_nb is embedded in the struct esb_dev which can be freed on its
device removal and before the chardev is closed, thus UAF at reboot:
[ 7.728581] esb_probe: esb_dev.watchdog_device ffff91316f91ab28
ts# uname -r note the address ^^^
5.5.0-rc5-ae6088-wdog
ts# ./openwdog0 &
[1] 696
ts# opened /dev/watchdog0, sleeping 10s...
ts# echo 1 > /sys/devices/pci0000\:00/0000\:00\:09.0/remove
[ 178.086079] devres:rel_nodes: dev ffff91317668a0b0 data ffff91316f91ab28
esb_dev.watchdog_device.reboot_nb memory is freed here ^^^
ts# ...woken up
[ 181.459010] devres:rel_nodes: dev ffff913171781000 data ffff913174a1dae8
[ 181.460195] devm_unreg_reboot_notifier: res ffff913174a1dae8 nb ffff91316f91ab78
attempt to use memory already freed ^^^
[ 181.461063] devm_unreg_reboot_notifier: nb->call 6b6b6b6b6b6b6b6b
[ 181.461243] devm_unreg_reboot_notifier: nb->next 6b6b6b6b6b6b6b6b
freed memory is filled with a slub poison ^^^
[1]+ Done ./openwdog0
ts# reboot
[ 229.921862] systemd-shutdown[1]: Rebooting.
[ 229.939265] notifier_call_chain: nb ffffffff9c6c2f20 nb->next ffffffff9c6d50c0
[ 229.943080] notifier_call_chain: nb ffffffff9c6d50c0 nb->next 6b6b6b6b6b6b6b6b
[ 229.946054] notifier_call_chain: nb 6b6b6b6b6b6b6b6b INVAL
[ 229.957584] general protection fault: 0000 [#1] SMP
[ 229.958770] CPU: 0 PID: 1 Comm: systemd-shutdow Not tainted 5.5.0-rc5-ae6088-wdog
[ 229.960224] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 229.963288] RIP: 0010:notifier_call_chain+0x66/0xd0
[ 229.969082] RSP: 0018:ffffb20dc0013d88 EFLAGS: 00010246
[ 229.970812] RAX: 000000000000002e RBX: 6b6b6b6b6b6b6b6b RCX: 00000000000008b3
[ 229.972929] RDX: 0000000000000000 RSI: 0000000000000096 RDI: ffffffff9ccc46ac
[ 229.975028] RBP: 0000000000000001 R08: 0000000000000000 R09: 00000000000008b3
[ 229.977039] R10: 0000000000000001 R11: ffffffff9c26c740 R12: 0000000000000000
[ 229.979155] R13: 6b6b6b6b6b6b6b6b R14: 0000000000000000 R15: 00000000fffffffa
... slub_debug=FZP poison ^^^
[ 229.989089] Call Trace:
[ 229.990157] blocking_notifier_call_chain+0x43/0x59
[ 229.991401] kernel_restart_prepare+0x14/0x30
[ 229.992607] kernel_restart+0x9/0x30
[ 229.993800] __do_sys_reboot+0x1d2/0x210
[ 230.000149] do_syscall_64+0x3d/0x130
[ 230.001277] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 230.002639] RIP: 0033:0x7f5461bdd177
[ 230.016402] Modules linked in: i6300esb
[ 230.050261] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Fix the crash by reverting 44ea39420fc9 so unregister_reboot_notifier()
is called when watchdog device is removed. This also makes handling of
the reboot notifier unified with the handling of the restart handler,
which is freed with unregister_restart_handler() in the same place.
Fixes: 44ea39420fc9 ("drivers/watchdog: make use of devm_register_reboot_notifier()") Cc: stable@vger.kernel.org # v4.15+ Signed-off-by: Vladis Dronov <vdronov@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200108125347.6067-1-vdronov@redhat.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The function padata_flush_queues is fundamentally broken because
it cannot force padata users to complete the request that is
underway. IOW padata has to passively wait for the completion
of any outstanding work.
As it stands flushing is used in two places. Its use in padata_stop
is simply unnecessary because nothing depends on the queues to
be flushed afterwards.
The other use in padata_replace is more substantial as we depend
on it to free the old pd structure. This patch instead uses the
pd->refcnt to dynamically free the pd structure once all requests
are complete.
Fixes: 2b73b07ab8a4 ("padata: Flush the padata queues actively") Cc: <stable@vger.kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
scripts/find-unused-docs.sh invokes scripts/kernel-doc to find out if a
source file contains kerneldoc or not.
However, as it passes the no longer supported "-text" option to
scripts/kernel-doc, the latter prints out its help text, causing all
files to be considered containing kerneldoc.
Get rid of these false positives by removing the no longer supported
"-text" option from the scripts/kernel-doc invocation.
Cc: stable@vger.kernel.org # 4.16+ Fixes: b05142675310d2ac ("scripts: kernel-doc: get rid of unused output formats") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20200127093107.26401-1-geert+renesas@glider.be Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
On AXP288 and newer PMICs, bit 7 of AXP20X_VBUS_IPSOUT_MGMT can be set
to prevent using the VBUS input. However, when the VBUS unplugged and
plugged back in, the bit automatically resets to zero.
We need to set the register as volatile to prevent regmap from caching
that bit. Otherwise, regcache will think the bit is already set and not
write the register.
Fixes: cd53216625a0 ("mfd: axp20x: Fix axp288 volatile ranges") Cc: stable@vger.kernel.org Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The geode AES driver is heavily broken because it stores per-request
state in the transform context. So it will crash or produce the wrong
result if used by any of the many places in the kernel that issue
concurrent requests for the same transform object.
This driver is also implemented using the deprecated blkcipher API,
which makes it difficult to fix, and puts it among the drivers
preventing that API from being removed.
Convert this driver to use the skcipher API, and change it to not store
per-request state in the transform context.
Fixes: 9fe757b0cfce ("[PATCH] crypto: Add support for the Geode LX AES hardware") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Florian Bezdeka <florian@bezdeka.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Confusingly, there are three SPSR layouts that a kernel may need to deal
with:
(1) An AArch64 SPSR_ELx view of an AArch64 pstate
(2) An AArch64 SPSR_ELx view of an AArch32 pstate
(3) An AArch32 SPSR_* view of an AArch32 pstate
When the KVM AArch32 support code deals with SPSR_{EL2,HYP}, it's either
dealing with #2 or #3 consistently. On arm64 the PSR_AA32_* definitions
match the AArch64 SPSR_ELx view, and on arm the PSR_AA32_* definitions
match the AArch32 SPSR_* view.
However, when we inject an exception into an AArch32 guest, we have to
synthesize the AArch32 SPSR_* that the guest will see. Thus, an AArch64
host needs to synthesize layout #3 from layout #2.
This patch adds a new host_spsr_to_spsr32() helper for this, and makes
use of it in the KVM AArch32 support code. For arm64 we need to shuffle
the DIT bit around, and remove the SS bit, while for arm we can use the
value as-is.
I've open-coded the bit manipulation for now to avoid having to rework
the existing PSR_* definitions into PSR64_AA32_* and PSR32_AA32_*
definitions. I hope to perform a more thorough refactoring in future so
that we can handle pstate view manipulation more consistently across the
kernel tree.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200108134324.46500-4-mark.rutland@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit f92b070f2dc8 ("printk: Do not miss new messages when replaying
the log") introduced a new variable @exclusive_console_stop_seq to
store when an exclusive console should stop printing. It should be
set to the @console_seq value at registration. However, @console_seq
is previously set to @syslog_seq so that the exclusive console knows
where to begin. This results in the exclusive console immediately
reactivating all the other consoles and thus repeating the messages
for those consoles.
Set @console_seq after @exclusive_console_stop_seq has stored the
current @console_seq value.
Fixes: f92b070f2dc8 ("printk: Do not miss new messages when replaying the log") Link: http://lkml.kernel.org/r/20191219115322.31160-1-john.ogness@linutronix.de Cc: Steven Rostedt <rostedt@goodmis.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: John Ogness <john.ogness@linutronix.de> Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
A partition with Access Type 3 (rewritable) shall define a Freed
Space Bitmap or a Freed Space Table, see 2.3.3. All other partitions
shall not define a Freed Space Bitmap or a Freed Space Table.
Rewritable partitions are used on media that require some form of
preprocessing before re-writing data (for example legacy MO). Such
partitions shall use Access Type 3.
Overwritable partitions are used on media that do not require
preprocessing before overwriting data (for example: CD-RW, DVD-RW,
DVD+RW, DVD-RAM, BD-RE, HD DVD-Rewritable). Such partitions shall
use Access Type 4.
however older versions of the standard didn't have this wording and
there are tools out there that create UDF filesystems with rewritable
partitions but that don't contain a Freed Space Bitmap or a Freed Space
Table on media that does not require pre-processing before overwriting a
block. So instead of forcing media with rewritable partition read-only,
base this decision on presence of a Freed Space Bitmap or a Freed Space
Table.
Reported-by: Pali Rohár <pali.rohar@gmail.com> Reviewed-by: Pali Rohár <pali.rohar@gmail.com> Fixes: b085fbe2ef7f ("udf: Fix crash during mount") Link: https://lore.kernel.org/linux-fsdevel/20200112144735.hj2emsoy4uwsouxz@pali Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit e5e884b42639 ("libertas: Fix two buffer overflows at parsing bss
descriptor") introduced a bounds check on the number of supplied rates to
lbs_ibss_join_existing() and made it to return on overflow.
However, the aforementioned commit doesn't set the return value accordingly
and thus, lbs_ibss_join_existing() would return with zero even though it
failed.
Make lbs_ibss_join_existing return -EINVAL in case the bounds check on the
number of supplied rates fails.
Fixes: e5e884b42639 ("libertas: Fix two buffer overflows at parsing bss descriptor") Signed-off-by: Nicolai Stange <nstange@suse.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Commit e5e884b42639 ("libertas: Fix two buffer overflows at parsing bss
descriptor") introduced a bounds check on the number of supplied rates to
lbs_ibss_join_existing().
Unfortunately, it introduced a return path from within a RCU read side
critical section without a corresponding rcu_read_unlock(). Fix this.
Fixes: e5e884b42639 ("libertas: Fix two buffer overflows at parsing bss descriptor") Signed-off-by: Nicolai Stange <nstange@suse.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
mwifiex_cmd_append_vsie_tlv() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Qing Xu <m1s5p6688@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
mwifiex_ret_wmm_get_status() calls memcpy() without checking the
destination size.Since the source is given from remote AP which
contains illegal wmm elements , this may trigger a heap buffer
overflow.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Qing Xu <m1s5p6688@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently we are doing a read of the status register.
Move the spinlock after that as the reads need not be spinlock
protected. This patch prevents relaxing the cpu with spinlock held.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Cc: Pavel Machek <pavel@denx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Move blk_queue_make_request() to dm.c:alloc_dev() so that
q->make_request_fn is never NULL during the lifetime of a DM device
(even one that is created without a DM table).
Otherwise generic_make_request() will crash simply by doing:
dmsetup create -n test
mount /dev/dm-N /mnt
While at it, move ->congested_data initialization out of
dm.c:alloc_dev() and into the bio-based specific init method.
Reported-by: Stefan Bader <stefan.bader@canonical.com> BugLink: https://bugs.launchpad.net/bugs/1860231 Fixes: ff36ab34583a ("dm: remove request-based logic from make_request_fn wrapper")
Depends-on: c12c9a3c3860c ("dm: various cleanups to md->queue initialization code") Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[smb: adjusted for context and dm_init_md_queue() exitsting in older
kernels] Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Driver initiates OCR if a DCMD command times out. But there is a deadlock
if the driver attempts to invoke another OCR before the mutex lock
(reset_mutex) is released from the previous session of OCR.
This patch takes care of the above scenario using new flag
MEGASAS_FUSION_OCR_NOT_POSSIBLE to indicate if OCR is possible.
Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/1579000882-20246-9-git-send-email-anand.lodnoor@broadcom.com Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Signed-off-by: Anand Lodnoor <anand.lodnoor@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Enclose multiple macro parameters in parentheses in order to
make such macros safer and fix the Clang warning below:
drivers/media/i2c/adv748x/adv748x-afe.c:452:12: warning: operator '?:'
has lower precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
HMAC keys can be of any length, and atmel_sha_hmac_key_set() can only
fail due to -ENOMEM. But atmel_sha_hmac_setkey() incorrectly treated
any error as a "bad key length" error. Fix it to correctly propagate
the -ENOMEM error code and not set any tfm result flags.
Fixes: 81d8750b2b59 ("crypto: atmel-sha - add support to hmac(shaX)") Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
kvm_test_age_hva() is called upon mmu_notifier_test_young(), but wrong
address range has been passed to handle_hva_to_gpa(). With the wrong
address range, no young bits will be checked in handle_hva_to_gpa().
It means zero is always returned from mmu_notifier_test_young().
This fixes the issue by passing correct address range to the underly
function handle_hva_to_gpa(), so that the hardware young (access) bit
will be visited.
The NO_FPSIMD capability is defined with scope SYSTEM, which implies
that the "absence" of FP/SIMD on at least one CPU is detected only
after all the SMP CPUs are brought up. However, we use the status
of this capability for every context switch. So, let us change
the scope to LOCAL_CPU to allow the detection of this capability
as and when the first CPU without FP is brought up.
Also, the current type allows hotplugged CPU to be brought up without
FP/SIMD when all the current CPUs have FP/SIMD and we have the userspace
up. Fix both of these issues by changing the capability to
BOOT_RESTRICTED_LOCAL_CPU_FEATURE.
Fixes: 82e0191a1aa11abf ("arm64: Support systems without FP/ASIMD") Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
As of commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly"), free_memmap() might not always be inlined, and thus is
triggering a section warning:
WARNING: vmlinux.o(.text.unlikely+0x904): Section mismatch in reference from the function free_memmap() to the function .meminit.text:memblock_free()
Mark it as __init, since the faller (free_unused_memmap) already is.
Fixes: ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly") Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Saving/restoring an unmapped collection is a valid scenario. For
example this happens if a MAPTI command was sent, featuring an
unmapped collection. At the moment the CTE fails to be restored.
Only compare against the number of online vcpus if the rdist
base is set.
By default a pseries guest supports a H_PUT_TCE hypercall which maps
a single IOMMU page in a DMA window. Additionally the hypervisor may
support H_PUT_TCE_INDIRECT/H_STUFF_TCE which update multiple TCEs at once;
this is advertised via the device tree /rtas/ibm,hypertas-functions
property which Linux converts to FW_FEATURE_MULTITCE.
FW_FEATURE_MULTITCE is checked when dma_iommu_ops is used; however
the code managing the huge DMA window (DDW) ignores it and calls
H_PUT_TCE_INDIRECT even if it is explicitly disabled via
the "multitce=off" kernel command line parameter.
This adds FW_FEATURE_MULTITCE checking to the DDW code path.
This changes tce_build_pSeriesLP to take liobn and page size as
the huge window does not have iommu_table descriptor which usually
the place to store these numbers.
Commit e5afdf9dd515 ("powerpc/vfio_spapr_tce: Add reference counting to
iommu_table") missed an iommu_table allocation in the pseries vio code.
The iommu_table is allocated with kzalloc and as a result the associated
kref gets a value of zero. This has the side effect that during a DLPAR
remove of the associated virtual IOA the iommu_tce_table_put() triggers
a use-after-free underflow warning.
If we compile tools/acpi target in the top source directory, we'd get a
compilation error showing as bellow:
# make tools/acpi
DESCEND power/acpi
DESCEND tools/acpidbg
CC tools/acpidbg/acpidbg.o
Assembler messages:
Fatal error: can't create /home/lzy/kernel-upstream/power/acpi/\
tools/acpidbg/acpidbg.o: No such file or directory
../../Makefile.rules:26: recipe for target '/home/lzy/kernel-upstream/\
power/acpi/tools/acpidbg/acpidbg.o' failed
make[3]: *** [/home/lzy/kernel-upstream//power/acpi/tools/acpidbg/\
acpidbg.o] Error 1
Makefile:19: recipe for target 'acpidbg' failed
make[2]: *** [acpidbg] Error 2
Makefile:54: recipe for target 'acpi' failed
make[1]: *** [acpi] Error 2
Makefile:1607: recipe for target 'tools/acpi' failed
make: *** [tools/acpi] Error 2
Fixes: d5a4b1a540b8 ("tools/power/acpi: Remove direct kernel source include reference") Signed-off-by: Zhengyuan Liu <liuzhengyuan@kylinos.cn> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.
The driver gets driver_data from memory that is marked as const (which
is probably put to read-only memory) and it then modifies it. This
likely causes some sort of fault to happen.
Fix this by taking a copy of the structure.
Fixes: c94a8ff14de3 ("platform/x86: intel_mid_powerbtn: make mid_pb_ddata const") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The rtc-cmos interrupt setting was changed in the commit 079062b28fb4
("rtc: cmos: prevent kernel warning on IRQ flags mismatch") in order
to allow shared interrupts; according to that commit's description,
some machine got kernel warnings due to the interrupt line being shared
between rtc-cmos and other hardware, and rtc-cmos didn't allow IRQ sharing
that time.
After the aforementioned commit though it was observed a huge increase
in lost HPET interrupts in some systems, observed through the following
kernel message:
[...] hpet1: lost 35 rtc interrupts
After investigation, it was narrowed down to the shared interrupts
usage when having the kernel option "irqpoll" enabled. In this case,
all IRQ handlers are called for non-timer interrupts, if such handlers
are setup in shared IRQ lines. The rtc-cmos IRQ handler could be set to
hpet_rtc_interrupt(), which will produce the kernel "lost interrupts"
message after doing work - lots of readl/writel to HPET registers, which
are known to be slow.
Although "irqpoll" is not a default kernel option, it's used in some contexts,
one being the kdump kernel (which is an already "impaired" kernel usually
running with 1 CPU available), so the performance burden could be considerable.
Also, the same issue would happen (in a shorter extent though) when using
"irqfixup" kernel option.
In a quick experiment, a virtual machine with uptime of 2 minutes produced
>300 calls to hpet_rtc_interrupt() when "irqpoll" was set, whereas without
sharing interrupts this number reduced to 1 interrupt. Machines with more
hardware than a VM should generate even more unnecessary HPET interrupts
in this scenario.
---8<---8<---8<---
After looking into the rtc-cmos driver history and DSDT table from
the Microsoft Surface 3, we may notice that Hans de Goede submitted
a correct fix (see dependency below). Thus, we simply revert
the culprit commit.
Fixes: 079062b28fb4 ("rtc: cmos: prevent kernel warning on IRQ flags mismatch")
Depends-on: a1e23a42f1bd ("rtc: cmos: Do not assume irq 8 for rtc when there are no legacy irqs") Reported-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200123131437.28157-1-andriy.shevchenko@linux.intel.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com> Signed-off-by: Khalid Elmously <khalid.elmously@canonical.com>
The current code returns -EPERM when the voltage loss bit is set.
Since the bit indicates that the time value is not valid, return
-EINVAL instead, which is the appropriate error code for this
situation.