Johan Hedberg [Tue, 8 Nov 2011 23:44:22 +0000 (01:44 +0200)]
Bluetooth: Fix cancel_delayed_work_sync usage with locks
The cancel_delayed_work_sync function should not be used if we hold any
locks. Luckily all places where this is the case it is also safe to use
the non-sync version.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Tue, 8 Nov 2011 18:40:15 +0000 (20:40 +0200)]
Bluetooth: Move pending management command list into struct hci_dev
This patch moves the pending management command list (previously global
to mgmt.c) into struct hci_dev. This makes it possible to do proper
locking when accessing it (through the existing hci_dev locks) and
thereby avoid race conditions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Tue, 8 Nov 2011 18:40:14 +0000 (20:40 +0200)]
Bluetooth: Pass full hci_dev struct to mgmt callbacks
The current global pending command list in mgmt.c is racy. Possibly the
simplest way to fix it is to have per-hci dev lists instead of a global
one (all commands that need a pending struct are hci_dev specific).
This way the list can be protected using the already existing per-hci
dev lock. To enable this refactoring the first thing that needs to be
done is to ensure that the mgmt functions have access to the hci_dev
struct (instead of just the dev id).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Thomas Pedersen [Wed, 26 Oct 2011 21:47:29 +0000 (14:47 -0700)]
mac80211: allow frame aggregation for mesh
Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Ashok Nagarajan <anagar6@uic.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Wed, 26 Oct 2011 21:47:28 +0000 (14:47 -0700)]
mac80211: set HT capabilities for mesh peer
Set peer's HT capabilities, and disallow peering if we're on a different
channel type.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Ashok Nagarajan <anagar6@uic.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Wed, 26 Oct 2011 21:47:27 +0000 (14:47 -0700)]
mac80211: add HT IEs to mesh frames
Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Ashok Nagarajan <anagar6@uic.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: Add btcoex profile management support for AR9462
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arik Nemtsov [Sun, 23 Oct 2011 06:21:41 +0000 (08:21 +0200)]
mac80211: support adding IV-room in the skb for CCMP keys
Some cards can generate CCMP IVs in HW, but require the space for the IV
to be pre-allocated in the frame at the correct offset. Add a key flag
that allows us to achieve this.
Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 22 Oct 2011 17:05:51 +0000 (19:05 +0200)]
nl80211: clean up genlmsg_end uses
genlmsg_end() cannot fail, it just returns the length
of the message. Thus, error handling for it is useless.
While removing it, I also noticed a useless variable
and removed this it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 21 Oct 2011 14:16:35 +0000 (16:16 +0200)]
brcm80211: smac: change buffer endianess convert function interface
The buffer endianess conversion functions in srom.c had a size
argument giving number of bytes but the function converts words.
Providing the number of words to the function is more sensible
so that is done in this patch.
Reported-by: Pavel Roskin <proski@gnu.org> Reported-by: Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 21 Oct 2011 14:16:34 +0000 (16:16 +0200)]
brcm80211: fmac: remove state from brcmf_if in fullmac
The usage of state decrease readability. Optimize the code flow to
get rid of it
Reviewed-by: Roland Vossen <rvossen@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 21 Oct 2011 14:16:33 +0000 (16:16 +0200)]
brcm80211: fmac: store brcmf_if in net device private data
Make a proper use of private data area of net device by storing
interface related data structure instead of generic driver data
Reported-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 21 Oct 2011 14:16:32 +0000 (16:16 +0200)]
brcm80211: fmac: use brcmf_add_if for all net devices
Use brcmf_add_if for primary and virtual net device interfaces. This
is part of the net device interface clean up for fullmac.
Reviewed-by: Roland Vossen <rvossen@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Fri, 21 Oct 2011 14:16:31 +0000 (16:16 +0200)]
brcm80211: smac: use sk_buff list for handling frames in receive path
In the receive path the frames are obtained from the dma using
multiple sk_buff that were linked using the skb next pointer.
This has been changed and it now used sk_buff lists and skb_queue
functions instead.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Fri, 21 Oct 2011 14:16:29 +0000 (16:16 +0200)]
brcm80211: smac: changed check to confirm STA only support
The driver currently only supports STA operation. However, in
brcms_ops_add_interface() also AP and SSID mode were accepted.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Fri, 21 Oct 2011 14:16:28 +0000 (16:16 +0200)]
brcm80211: smac: mute transmit on ops_start
Monitor mode functionality (not functional yet) requires transmit to be
muted after ops_start() is called, transmit is unmuted when the first
interface is added.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon ops_start(), a Mac80211 driver should enable receive functionality to
support monitor mode. Also, upon ops_stop(), it should disable rx.
Driver did not follow this rule so code has been changed.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Fri, 21 Oct 2011 14:16:26 +0000 (16:16 +0200)]
brcm80211: smac: fixed inconsistency in transmit mute
Transmit was muted in two ways: full mute and a partial mute called
'pre ism cac time' mute. But, this 'pre ism cac time' mute was done at
one place in the code (when tx_mute == false), and overridden later
on in another place in code.
To fix this, the 'pre ism cac time' mute has been replaced by a non
mute.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Fri, 21 Oct 2011 14:16:25 +0000 (16:16 +0200)]
brcm80211: smac: bugfix for tx mute in brcms_b_init()
Transmit can only be muted if the mac core is enabled. When brcms_b_init()
is called, the mac core is suspended. Brcms_b_init() calls a transmit mute
function that requires an enabled mac core. This code path is never taken,
but would have been taken in subsequent patches.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Softmac would bring its interface down on an RF kill switch condition,
without Mac80211 intervention. Because Mac80211 should be the only party
initiating interfaces going up and down, this functionality has been
removed.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Softmac would bring its interface down on a certain Minimum Power Save
related condition, without Mac80211 intervention. Because Mac80211 should
be the only party initiating interfaces going up and down, this functionality
has been removed. All notions of 'MPC' have been removed in the code as
well.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Fri, 21 Oct 2011 14:16:21 +0000 (16:16 +0200)]
brcm80211: smac: removed MPC related code
The chip init sequence enables MPC (Minimum Power Consumption), but the
driver disables it after that. As there are no interfaces to enable this
mode the related code is unused (member variable wlc->mpc is false).
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 21 Oct 2011 14:16:20 +0000 (16:16 +0200)]
brcm80211: fmac: use brcmf_del_if for all net devices
Use brcmf_del_if for primary and virtual net device interfaces. This
is part of the net device interface clean up for fullmac.
Reviewed-by: Roland Vossen <rvossen@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Fri, 21 Oct 2011 14:16:19 +0000 (16:16 +0200)]
brcm80211: fmac: allow wd timer to be disabled when bus down
Watchdog timer should be able to be stopped even firmware is not
loaded.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Wed, 19 Oct 2011 10:51:09 +0000 (12:51 +0200)]
brcm80211: fmac: use sk_buff list for handling frames in receive path
The functions in the receive patch of the fullmac now use sk_buff
list and skb_queue_xx() functions instead of dealing with list pointers
in the sk_buff directly.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Tue, 18 Oct 2011 22:52:01 +0000 (17:52 -0500)]
rtl8192cu: Add new device IDs
The latest vendor (non-mac80211) driver of 9/22/2011 shows some new
device IDs for rtl8192cu. In addition, some typos in the table are
fixed and one duplicate is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 18 Oct 2011 12:03:10 +0000 (14:03 +0200)]
brcm80211: util: remove function brcmu_format_hex() from brcmutil
The function brcmu_format_hex() filled a string buffer with byte
values from a data buffer. The calling function used this string
buffer in a printk. Now the calling function uses the kernel
function print_hex_dump_bytes().
Reported-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 18 Oct 2011 12:03:09 +0000 (14:03 +0200)]
brcm80211: util: move brcmu_pktfrombuf() function to brcmfmac
The function brcmu_pktfrombuf was only used in the brcmfmac source
and has been moved there. It has been refactored to match its use.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 18 Oct 2011 12:03:08 +0000 (14:03 +0200)]
brcm80211: smac: remove phy api bypass in rate.h
Obviously the phy api should be used to interface with the phy. In
rate.h a table within phy was accessed directly by declaring the
table extern in rate.h itself. This patch fixes this using the
provided api function to obtain the table reference. This bypass
was found by a sparse warning on the table not being defined static.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 18 Oct 2011 12:03:07 +0000 (14:03 +0200)]
brcm80211: smac: some local function made static in main.c
In main.c a couple of functions were not static although they
were only locally used. Sparse gave warnings on them and these
functions have been made static.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 18 Oct 2011 12:03:06 +0000 (14:03 +0200)]
brcm80211: smac: avoid sprom endianess conversions for crc8 check
The data from the sprom consists of u16 values stored in little
endian notation over which a crc8 was determined. To validate this
the buffer needed to be converted for big-endian systems. Reading
the sprom data is now done per byte so conversion is only done
after a successful crc8 check.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 18 Oct 2011 12:03:05 +0000 (14:03 +0200)]
brcm80211: smac: remove obsolete srom variables from n-phy
The n-phy requested some srom variables that are no longer needed
and consequently not present in the srom revision 8 and higher that
this driver support. This code has been removed from the n-phy.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Tue, 18 Oct 2011 12:03:04 +0000 (14:03 +0200)]
brcm80211: smac: indicate severe problems to Mac80211
In case the hardware crashes, a reinitialization internal to the driver
was performed. Since Mac80211 must be in the know of such an event as
well, ieee80211_restart_hw() is now called.
Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Tue, 18 Oct 2011 12:03:03 +0000 (14:03 +0200)]
brcm80211: fmac: changed two scan related structures
struct brcmf_scan_results contained a 1 element array, but in reality
the number of scan results can be 0 or more, as indicated by the
count field in the same struct. Array has be redefined to be 0 elements
length to indicate the array is purely for reference.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Tue, 18 Oct 2011 12:03:02 +0000 (14:03 +0200)]
brmc80211: fmac: reworked next_bss()
Moved function to where it is called and made it more readable.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Vossen [Tue, 18 Oct 2011 12:03:01 +0000 (14:03 +0200)]
brcm80211: fmac: annotated little endian struct with _le
Made code more readable.
Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Signed-off-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 18 Oct 2011 12:02:59 +0000 (14:02 +0200)]
brcm80211: smac: drop "40MHz intolerant" flag from HT capability info
The brcmsmac driver registered with mac80211 with HT capability info
set to 40MHz intolerant. This cause any other station on the channel
to be forced to use 20MHz. This flag has been removed.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Reviewed-by: Alwin Beukers <alwin@broadcom.com> Reviewed-by: Roland Vossen <rvossen@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alwin Beukers [Tue, 18 Oct 2011 12:02:57 +0000 (14:02 +0200)]
brcm80211: cleanup defines in main.c
Signed-off-by: Alwin Beukers <alwin@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Tue, 18 Oct 2011 06:50:43 +0000 (09:50 +0300)]
iwmc3200wifi: add some more range checks
My previous patch added a check to get_key() but missed a couple
other places which need range checks.
The problem here is that wifi drivers have different numbers of keys.
The lower levels assume that they can have up to 4 default keys and
2 management keys but this driver only has the default keys so we
could go past the end of the ->keys[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Tue, 18 Oct 2011 06:47:29 +0000 (09:47 +0300)]
rndis_wlan: add range check in del_key()
Wifi drivers can have up to 6 keys but the rndis_wlan only has 4 so
it needs to have its own checks to make sure we don't go out of
bounds. The add_key() function already checks but I added some
checks to del_key() and set_default_key().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Mon, 17 Oct 2011 07:28:23 +0000 (10:28 +0300)]
ath9k_hw: min_t() casts u32 to int
The code here treats very large values of "limit" as less than
MAX_POWER_RATE because of the cast to int. We should do the compare
as u32 instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Sun, 16 Oct 2011 08:57:31 +0000 (10:57 +0200)]
mac80211: call set_wmm_default only for valid vifs
mac80211 calls ieee80211_set_wmm_default (which in turn
calls drv_conf_tx()) for every new interface, including
"internal" ones (e.g. monitor interface, which the low-level
driver doesn't know about).
Limit this call only to valid interfaces.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 14 Oct 2011 19:54:48 +0000 (12:54 -0700)]
iwlagn: use 6 Mbps rate for no-CCK scans
When userspace requested that a scan not be
done with CCK rates, use 6 Mbps. This is used
for example for P2P scanning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Fri, 14 Oct 2011 19:54:46 +0000 (12:54 -0700)]
iwlagn: simplify iwl_alloc_all
The iwl_alloc_all routine is only called once. Delete the argument
and print an error in the calling routine if needed.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don Fry [Fri, 14 Oct 2011 19:54:44 +0000 (12:54 -0700)]
iwlagn: remove unnecessary type for tracing operations
The device tracing routines only use the priv pointer as an opaque
value. Change from a typed iwl_priv pointer to a null pointer and
eliminate the need to include iwl_priv.h. CMD_ASYNC is defined in
iwl_shared.h which is the only reason it is included.
Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 14 Oct 2011 19:54:43 +0000 (12:54 -0700)]
iwlagn: update wowlan API
The WoWLAN API changed due to netdetect and
we now have a more generic "D3 configuration"
command that enables the sysassert & rfkill
wakeup triggers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Tue, 8 Nov 2011 13:01:13 +0000 (14:01 +0100)]
ath: Fix NULL ptr dereference in ath_reg_apply_world_flags
This happens with devices using a regulatory domain 0x68 that are only
5Ghz capable because ath_reg_apply_active_scan_flags assumes that we
always have a 2,4Ghz band.
Johan Hedberg [Mon, 7 Nov 2011 21:13:39 +0000 (23:13 +0200)]
Bluetooth: Add address type fields to mgmt messages that need them
This patch adds address type info (typically BR/EDR vs LE) to management
messages that need this. This also ensures conformance to the latest
management API specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Mon, 7 Nov 2011 21:13:38 +0000 (23:13 +0200)]
Bluetooth: Update link key mgmt APIs to match latest spec.
BR/EDR link keys have their own commands and events (separate from SMP)
and the remove_keys command (previously remove_key) removes keys of any
kind for the specified remote address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Mon, 7 Nov 2011 20:16:02 +0000 (22:16 +0200)]
Bluetooth: Add timeout field to mgmt_set_discoverable
Based on the revised mgmt API set_discoverable has a timeout parameter
to specify how long the adapter will remain discoverable. A value of 0
means "indefinitively".
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Fri, 4 Nov 2011 17:16:53 +0000 (14:16 -0300)]
Bluetooth: Periodic Inquiry and Discovery
By using periodic inquiry command we're not able to detect correctly
when the controller has started inquiry.
Today we have this workaround in inquiry result event handler
to set the HCI_INQUIRY flag when it sees the first inquiry result
event. This workaround isn't enough because the device may be
performing an inquiry but the HCI_INQUIRY flag is not set. For
instance, if there is no device in range, no inquiry result event
is generated, consequently, the HCI_INQUIRY flags isn't set when
it should so.
We rely on HCI_INQUIRY flag to implement the discovery procedure
properly. So, as we aren't able to clear/set the HCI_INQUIRY flag
in a reliable manner, periodic inquiry events shouldn't change
the HCI_INQUIRY flag.
Thus, due to that issue and in order to keep compatibility with
userspace, periodic inquiry events shouldn't send mgmt discovering
events.
In future, we might track if periodic inquiry is enabled or not.
By tracking this state we'll be able to do some improvements in
Discovery such as failing MGMT_OP_START_DISCOVERY command in case
periodic inquiry is on. We can also send no mgmt_device_found
event if periodic inquiry is on.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Fri, 4 Nov 2011 17:16:52 +0000 (14:16 -0300)]
Bluetooth: Create hci_cancel_inquiry()
This patch adds a function to hci_core to cancel an ongoing inquiry.
According to the Bluetooth spec, the inquiry cancel command should
only be issued after the inquiry command has been issued, a command
status event has been received for the inquiry command, and before
the inquiry complete event occurs.
As HCI_INQUIRY flag is only set just after an inquiry command status
event occurs and it is cleared just after an inquiry complete event
occurs, the inquiry cancel command should be issued only if HCI_INQUIRY
flag is set.
Additionally, cancel inquiry related code from stop_discovery() were
replaced by a hci_cancel_inquiry() call.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add parsing Extended Flow Specification in L2CAP Config Response.
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Johan Hedberg [Thu, 3 Nov 2011 22:17:45 +0000 (00:17 +0200)]
Bluetooth: Clean up logic in hci_cc_write_scan_enable
This patch adds a new label to hci_cc_write_scan_enable to avoid
unnecessary indentation. This will be convenient especially when new
code for the discoverable timeout gets added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Wed, 2 Nov 2011 23:18:35 +0000 (16:18 -0700)]
Bluetooth: Add signal handlers for channel moves
AMP channels can be moved between BR/EDR and AMP controllers using a
sequence of signals. Every attempted channel move involves a series of
four signals:
Mat Martineau [Wed, 2 Nov 2011 23:18:31 +0000 (16:18 -0700)]
Bluetooth: Add AMP-related data and structures for channel signals
AMP channel creation and channel moves are coordinated using the L2CAP
signaling channel. These definitions cover the "create channel",
"move channel", and "move channel confirm" signals.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mat Martineau [Wed, 2 Nov 2011 23:18:28 +0000 (16:18 -0700)]
Bluetooth: Add BT_CHANNEL_POLICY socket option
Allow control of AMP functionality on L2CAP sockets. By default,
connections will be restricted to BR/EDR. Manipulating the
BT_CHANNEL_POLICY option allows for channels to be moved to or created
on AMP controllers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: use buffer priority to mark URB_ISO_ASAP flag
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: recalculate priorities when channels are starving
To avoid starvation the priority is recalculated so that the starving
channels are promoted to HCI_PRIO_MAX - 1 (6).
HCI_PRIO_MAX (7) is considered special, because it requires CAP_NET_ADMIN
capability which can be used to provide more guaranties, so it is not used
when promoting.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The quote is calculated based on the first buffer in the queue so if the
priority changes to something lower than the priority of the first skb
the quote needs to be recalculated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This implement priority based scheduler using skbuffer priority set via
SO_PRIORITY socket option.
It introduces hci_chan_hash (list of HCI Channel/hci_chan) per connection,
each item in this list refer to a L2CAP connection and it is used to
queue the data for transmission.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David Herrmann [Tue, 1 Nov 2011 16:27:50 +0000 (17:27 +0100)]
Bluetooth: hidp: Fix module reference cleanup
Calling module_put(THIS_MODULE) is *never* safe when we cannot go sure that we
own at least two references. This is because the call may unload our module
before it returns and then the "return" will jump into invalid memory.
Gladly, module.h provides a wrapper for kthread-users: module_put_and_exit().
This puts our module and then exits the kthread without returning to the module.
This patch fixes the hidp kthread to use this wrapper instead of manually
freeing its own reference. See nfsd or lockd for other kthreads using this.
Calling __module_get() inside the kthread is safe as the hidp module will always
wait until the kthread sets "waiting_for_startup" to 0.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
projects / mirror_ubuntu-disco-kernel.git / log