Add support for a RELASE build

[mirror_edk2.git] / BeagleBoardPkg / BeagleBoardPkg.fdf

# FLASH layout file for Beagle board.
#
# Copyright (c) 2009, Apple Inc. All rights reserved.
#
#  All rights reserved. This program and the accompanying materials
#    are licensed and made available under the terms and conditions of the BSD License
#    which accompanies this distribution. The full text of the license may be found at
#    http://opensource.org/licenses/bsd-license.php
#
#    THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
#    WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
#

################################################################################
#
# FD Section
# The [FD] Section is made up of the definition statements and a
# description of what goes into  the Flash Device Image.  Each FD section
# defines one flash "device" image.  A flash device image may be one of
# the following: Removable media bootable image (like a boot floppy
# image,) an Option ROM image (that would be "flashed" into an add-in
# card,) a System "Flash"  image (that would be burned into a system's
# flash) or an Update ("Capsule") image that will be used to update and
# existing system flash.
#
################################################################################


[FD.BeagleBoard_EFI]
####BaseAddress   = 0x80208000|gEmbeddedTokenSpaceGuid.PcdEmbeddedFdBaseAddress  #The base address of the FLASH Device.
BaseAddress   = 0x80008000|gEmbeddedTokenSpaceGuid.PcdEmbeddedFdBaseAddress  #The base address of the FLASH Device.
Size          = 0x00080000|gEmbeddedTokenSpaceGuid.PcdEmbeddedFdSize         #The size in bytes of the FLASH Device
ErasePolarity = 1
BlockSize     = 0x40
NumBlocks     = 0x2000

################################################################################
#
# Following are lists of FD Region layout which correspond to the locations of different
# images within the flash device.
#
# Regions must be defined in ascending order and may not overlap.
#
# A Layout Region start with a eight digit hex offset (leading "0x" required) followed by
# the pipe "|" character, followed by the size of the region, also in hex with the leading
# "0x" characters. Like:
# Offset|Size
# PcdOffsetCName|PcdSizeCName
# RegionType <FV, DATA, or FILE>
#
################################################################################

# 512 bytes of configuration header & 8 bytes of image header
0x00000000|0x00000208

0x00000208|0x0007FDF8
gEmbeddedTokenSpaceGuid.PcdFlashFvMainBase|gEmbeddedTokenSpaceGuid.PcdFlashFvMainSize
FV = FVMAIN_COMPACT

################################################################################
#
# FV Section
#
# [FV] section is used to define what components or modules are placed within a flash
# device file.  This section also defines order the components and modules are positioned
# within the image.  The [FV] section consists of define statements, set statements and
# module statements.
#
################################################################################

[FV.FvMain]
BlockSize          = 0x40
NumBlocks          = 0         # This FV gets compressed so make it just big enough
FvAlignment        = 8         # FV alignment and FV attributes setting.
ERASE_POLARITY     = 1
MEMORY_MAPPED      = TRUE
STICKY_WRITE       = TRUE
LOCK_CAP           = TRUE
LOCK_STATUS        = TRUE
WRITE_DISABLED_CAP = TRUE
WRITE_ENABLED_CAP  = TRUE
WRITE_STATUS       = TRUE
WRITE_LOCK_CAP     = TRUE
WRITE_LOCK_STATUS  = TRUE
READ_DISABLED_CAP  = TRUE
READ_ENABLED_CAP   = TRUE
READ_STATUS        = TRUE
READ_LOCK_CAP      = TRUE
READ_LOCK_STATUS   = TRUE

  INF MdeModulePkg/Core/Dxe/DxeMain.inf 

  #
  # PI DXE Drivers producing Architectural Protocols (EFI Services) 
  #
  INF ArmPkg/Drivers/CpuDxe/CpuDxe.inf
  
  INF MdeModulePkg/Core/RuntimeDxe/RuntimeDxe.inf
  INF MdeModulePkg/Universal/SecurityStubDxe/SecurityStubDxe.inf
  INF MdeModulePkg/Universal/WatchdogTimerDxe/WatchdogTimer.inf
  INF MdeModulePkg/Universal/CapsuleRuntimeDxe/CapsuleRuntimeDxe.inf
  INF MdeModulePkg/Universal/Variable/EmuRuntimeDxe/EmuVariableRuntimeDxe.inf
  INF EmbeddedPkg/EmbeddedMonotonicCounter/EmbeddedMonotonicCounter.inf
   
  INF EmbeddedPkg/SimpleTextInOutSerial/SimpleTextInOutSerial.inf

  INF EmbeddedPkg/ResetRuntimeDxe/ResetRuntimeDxe.inf
  INF EmbeddedPkg/RealTimeClockRuntimeDxe/RealTimeClockRuntimeDxe.inf
  INF EmbeddedPkg/TemplateMetronomeDxe/TemplateMetronomeDxe.inf
  
  #
  # Semi-hosting filesystem
  #
  INF ArmPkg/Filesystem/SemihostFs/SemihostFs.inf
  
  #
  # Nand Flash
  #
  INF Omap35xxPkg/Flash/Flash.inf

  #
  # MMC/SD
  #
  INF Omap35xxPkg/MMCHSDxe/MMCHS.inf
  
  #
  # I2C
  #
  INF Omap35xxPkg/SmbusDxe/Smbus.inf
  
  #
  # SoC Drivers
  #
  INF Omap35xxPkg/Gpio/Gpio.inf
  INF Omap35xxPkg/InterruptDxe/InterruptDxe.inf
  INF Omap35xxPkg/TimerDxe/TimerDxe.inf 

  #
  # Power IC
  #
  INF Omap35xxPkg/TPS65950Dxe/TPS65950.inf

  #
  # FAT filesystem + GPT/MBR partitioning
  #
  INF MdeModulePkg/Universal/Disk/DiskIoDxe/DiskIoDxe.inf
  INF MdeModulePkg/Universal/Disk/PartitionDxe/PartitionDxe.inf
  INF FatPkg/EnhancedFatDxe/Fat.inf
  INF MdeModulePkg/Universal/Disk/UnicodeCollation/EnglishDxe/EnglishDxe.inf

  #
  # USB Support
  #

  INF Omap35xxPkg/PciEmulation/PciEmulation.inf

  #NOTE: Open source EHCI stack doesn't work on Beagleboard.
  #NOTE: UsbBus and UsbMassStorage don't work using iPhond SDK tool chain.
  #INF MdeModulePkg/Bus/Pci/EhciDxe/EhciDxe.inf
  #INF MdeModulePkg/Bus/Usb/UsbBusDxe/UsbBusDxe.inf
  #INF MdeModulePkg/Bus/Usb/UsbMassStorageDxe/UsbMassStorageDxe.inf

  #
  # UEFI application (Shell Embedded Boot Loader) 
  #  
  INF EmbeddedPkg/Ebl/Ebl.inf
  

  #
  # Bds
  #
  INF BeagleBoardPkg/Bds/Bds.inf

  #
  # Gdb Stub
  #
  #INF ArmPkg/Drivers/DebugSupportDxe/DebugSupportDxe.inf


[FV.FVMAIN_COMPACT]
FvAlignment        = 8
ERASE_POLARITY     = 1
MEMORY_MAPPED      = TRUE
STICKY_WRITE       = TRUE
LOCK_CAP           = TRUE
LOCK_STATUS        = TRUE
WRITE_DISABLED_CAP = TRUE
WRITE_ENABLED_CAP  = TRUE
WRITE_STATUS       = TRUE
WRITE_LOCK_CAP     = TRUE
WRITE_LOCK_STATUS  = TRUE
READ_DISABLED_CAP  = TRUE
READ_ENABLED_CAP   = TRUE
READ_STATUS        = TRUE
READ_LOCK_CAP      = TRUE
READ_LOCK_STATUS   = TRUE

  INF BeagleBoardPkg/Sec/Sec.inf
#  INF MdeModulePkg/Core/Dxe/DxeMain.inf 

  FILE FV_IMAGE = 9E21FD93-9C72-4c15-8C4B-E77F1DB2D792 {
    SECTION GUIDED EE4E5898-3914-4259-9D6E-DC7BD79403CF PROCESSING_REQUIRED = TRUE {
      SECTION FV_IMAGE = FVMAIN
    }
  }


################################################################################
#
# Rules are use with the [FV] section's module INF type to define
# how an FFS file is created for a given INF file. The following Rule are the default
# rules for the different module type. User can add the customized rules to define the
# content of the FFS file.
#
################################################################################


############################################################################
# Example of a DXE_DRIVER FFS file with a Checksum encapsulation section   # 
############################################################################
#
#[Rule.Common.DXE_DRIVER]
#  FILE DRIVER = $(NAMED_GUID) {
#    DXE_DEPEX    DXE_DEPEX Optional      |.depex
#    COMPRESS PI_STD {
#      GUIDED {
#        PE32     PE32                    |.efi
#        UI       STRING="$(MODULE_NAME)" Optional
#        VERSION  STRING="$(INF_VERSION)" Optional BUILD_NUM=$(BUILD_NUMBER)
#      }
#    }
#  }
#
############################################################################

[Rule.Common.SEC]
  FILE SEC = $(NAMED_GUID) RELOCS_STRIPPED {
    TE  TE    Align = 8      |.efi
  }

[Rule.Common.PEI_CORE]
  FILE PEI_CORE = $(NAMED_GUID) {
    TE     TE           |.efi
    UI     STRING ="$(MODULE_NAME)" Optional         
  }

[Rule.Common.PEIM]
  FILE PEIM = $(NAMED_GUID) {
     PEI_DEPEX PEI_DEPEX Optional        |.depex
     PE32      PE32                      |.efi
     UI       STRING="$(MODULE_NAME)" Optional         
  }

[Rule.Common.PEIM.TIANOCOMPRESSED]
  FILE PEIM = $(NAMED_GUID) DEBUG_MYTOOLS_IA32 {
    PEI_DEPEX PEI_DEPEX Optional         |.depex
    GUIDED A31280AD-481E-41B6-95E8-127F4C984779 PROCESSING_REQUIRED = TRUE {
      PE32      PE32                     |.efi
      UI        STRING="$(MODULE_NAME)" Optional
    }
  }

[Rule.Common.DXE_CORE]
  FILE DXE_CORE = $(NAMED_GUID) {
    PE32     PE32           |.efi
    UI       STRING="$(MODULE_NAME)" Optional
  }


[Rule.Common.UEFI_DRIVER]
  FILE DRIVER = $(NAMED_GUID) {
    DXE_DEPEX    DXE_DEPEX Optional      |.depex
    PE32         PE32                    |.efi
    UI           STRING="$(MODULE_NAME)" Optional
  }

[Rule.Common.DXE_DRIVER]
  FILE DRIVER = $(NAMED_GUID) {
    DXE_DEPEX    DXE_DEPEX Optional      |.depex
    PE32         PE32                    |.efi
    UI           STRING="$(MODULE_NAME)" Optional
  }

[Rule.Common.DXE_RUNTIME_DRIVER]
  FILE DRIVER = $(NAMED_GUID) {
    DXE_DEPEX    DXE_DEPEX Optional      |.depex
    PE32         PE32                    |.efi
    UI           STRING="$(MODULE_NAME)" Optional
  }


[Rule.Common.UEFI_APPLICATION]
  FILE APPLICATION = $(NAMED_GUID) {
    UI     STRING ="$(MODULE_NAME)" Optional         
    PE32   PE32                    |.efi
  }