[mirror_edk2.git] / EmbeddedPkg / Drivers / Lan9118Dxe / Lan9118DxeUtil.c

/** @file\r
*\r
*  Copyright (c) 2012-2014, ARM Limited. All rights reserved.\r
*\r
*  This program and the accompanying materials\r
*  are licensed and made available under the terms and conditions of the BSD License\r
*  which accompanies this distribution.  The full text of the license may be found at\r
*  http://opensource.org/licenses/bsd-license.php\r
*\r
*  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,\r
*  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.\r
*\r
**/\r
\r
#include "Lan9118Dxe.h"\r
\r
STATIC EFI_MAC_ADDRESS mZeroMac = { { 0 } };\r
\r
/**\r
  This internal function reverses bits for 32bit data.\r
\r
  @param  Value                 The data to be reversed.\r
\r
  @return                       Data reversed.\r
\r
**/\r
UINT32\r
ReverseBits (\r
  UINT32  Value\r
  )\r
{\r
  UINTN   Index;\r
  UINT32  NewValue;\r
\r
  NewValue = 0;\r
  for (Index = 0; Index < 32; Index++) {\r
    if ((Value & (1 << Index)) != 0) {\r
      NewValue = NewValue | (1 << (31 - Index));\r
    }\r
  }\r
\r
  return NewValue;\r
}\r
\r
/*\r
**  Create Ethernet CRC\r
**\r
**  INFO USED:\r
**    1: http://en.wikipedia.org/wiki/Cyclic_redundancy_check\r
**\r
**    2: http://www.erg.abdn.ac.uk/~gorry/eg3567/dl-pages/crc.html\r
**\r
**    3: http://en.wikipedia.org/wiki/Computation_of_CRC\r
*/\r
UINT32\r
GenEtherCrc32 (\r
  IN    EFI_MAC_ADDRESS *Mac,\r
  IN    UINT32 AddrLen\r
  )\r
{\r
  INT32 Iter;\r
  UINT32 Remainder;\r
  UINT8 *Ptr;\r
\r
  Iter = 0;\r
  Remainder = 0xFFFFFFFF;    // 0xFFFFFFFF is standard seed for Ethernet\r
\r
  // Convert Mac Address to array of bytes\r
  Ptr = (UINT8*)Mac;\r
\r
  // Generate the Crc bit-by-bit (LSB first)\r
  while (AddrLen--) {\r
    Remainder ^= *Ptr++;\r
    for (Iter = 0;Iter < 8;Iter++) {\r
      // Check if exponent is set\r
      if (Remainder & 1) {\r
        Remainder = (Remainder >> 1) ^ CRC_POLYNOMIAL;\r
      } else {\r
        Remainder = (Remainder >> 1) ^ 0;\r
      }\r
    }\r
  }\r
\r
  // Reverse the bits before returning (to Big Endian)\r
  //TODO: Need to be reviewed. Do we want to do a bit reverse or a byte reverse (in this case use SwapBytes32())\r
  return ReverseBits (Remainder);\r
}\r
\r
// Function to read from MAC indirect registers\r
UINT32\r
IndirectMACRead32 (\r
  UINT32 Index\r
  )\r
{\r
  UINT32 MacCSR;\r
\r
  // Check index is in the range\r
  ASSERT(Index <= 12);\r
\r
  // Wait until CSR busy bit is cleared\r
  while ((MmioRead32 (LAN9118_MAC_CSR_CMD) & MAC_CSR_BUSY) == MAC_CSR_BUSY);\r
\r
  // Set CSR busy bit to ensure read will occur\r
  // Set the R/W bit to indicate we are reading\r
  // Set the index of CSR Address to access desired register\r
  MacCSR = MAC_CSR_BUSY | MAC_CSR_READ | MAC_CSR_ADDR(Index);\r
\r
  // Write to the register\r
  MmioWrite32 (LAN9118_MAC_CSR_CMD, MacCSR);\r
\r
  // Wait until CSR busy bit is cleared\r
  while ((MmioRead32 (LAN9118_MAC_CSR_CMD) & MAC_CSR_BUSY) == MAC_CSR_BUSY);\r
\r
  // Now read from data register to get read value\r
  return MmioRead32 (LAN9118_MAC_CSR_DATA);\r
}\r
\r
// Function to write to MAC indirect registers\r
UINT32\r
IndirectMACWrite32 (\r
  UINT32 Index,\r
  UINT32 Value\r
  )\r
{\r
  UINT32 ValueWritten;\r
  UINT32 MacCSR;\r
\r
  // Check index is in the range\r
  ASSERT(Index <= 12);\r
\r
  // Wait until CSR busy bit is cleared\r
  while ((MmioRead32 (LAN9118_MAC_CSR_CMD) & MAC_CSR_BUSY) == MAC_CSR_BUSY);\r
\r
  // Set CSR busy bit to ensure read will occur\r
  // Set the R/W bit to indicate we are writing\r
  // Set the index of CSR Address to access desired register\r
  MacCSR = MAC_CSR_BUSY | MAC_CSR_WRITE | MAC_CSR_ADDR(Index);\r
\r
  // Now write the value to the register before issuing the write command\r
  ValueWritten = MmioWrite32 (LAN9118_MAC_CSR_DATA, Value);\r
\r
  // Write the config to the register\r
  MmioWrite32 (LAN9118_MAC_CSR_CMD, MacCSR);\r
\r
  // Wait until CSR busy bit is cleared\r
  while ((MmioRead32 (LAN9118_MAC_CSR_CMD) & MAC_CSR_BUSY) == MAC_CSR_BUSY);\r
\r
  return ValueWritten;\r
}\r
\r
// Function to read from MII register (PHY Access)\r
UINT32\r
IndirectPHYRead32 (\r
  UINT32 Index\r
  )\r
{\r
  UINT32 ValueRead;\r
  UINT32 MiiAcc;\r
\r
  // Check it is a valid index\r
  ASSERT(Index < 31);\r
\r
  // Wait for busy bit to clear\r
  while ((IndirectMACRead32 (INDIRECT_MAC_INDEX_MII_ACC) & MII_ACC_MII_BUSY) == MII_ACC_MII_BUSY);\r
\r
  // Clear the R/W bit to indicate we are reading\r
  // Set the index of the MII register\r
  // Set the PHY Address\r
  // Set the MII busy bit to allow read\r
  MiiAcc = MII_ACC_MII_READ | MII_ACC_MII_REG_INDEX(Index) | MII_ACC_PHY_VALUE | MII_ACC_MII_BUSY;\r
\r
  // Now write this config to register\r
  IndirectMACWrite32 (INDIRECT_MAC_INDEX_MII_ACC, MiiAcc & 0xFFFF);\r
\r
  // Wait for busy bit to clear\r
  while ((IndirectMACRead32 (INDIRECT_MAC_INDEX_MII_ACC) & MII_ACC_MII_BUSY) == MII_ACC_MII_BUSY);\r
\r
  // Now read the value of the register\r
  ValueRead = (IndirectMACRead32 (INDIRECT_MAC_INDEX_MII_DATA) & 0xFFFF); // only lower 16 bits are valid for any PHY register\r
\r
  return ValueRead;\r
}\r
\r
\r
// Function to write to the MII register (PHY Access)\r
UINT32\r
IndirectPHYWrite32 (\r
  UINT32 Index,\r
  UINT32 Value\r
  )\r
{\r
  UINT32 MiiAcc;\r
  UINT32 ValueWritten;\r
\r
  // Check it is a valid index\r
  ASSERT(Index < 31);\r
\r
  // Wait for busy bit to clear\r
  while ((IndirectMACRead32 (INDIRECT_MAC_INDEX_MII_ACC) & MII_ACC_MII_BUSY) == MII_ACC_MII_BUSY);\r
\r
  // Clear the R/W bit to indicate we are reading\r
  // Set the index of the MII register\r
  // Set the PHY Address\r
  // Set the MII busy bit to allow read\r
  MiiAcc = MII_ACC_MII_WRITE | MII_ACC_MII_REG_INDEX(Index) | MII_ACC_PHY_VALUE | MII_ACC_MII_BUSY;\r
\r
  // Write the desired value to the register first\r
  ValueWritten = IndirectMACWrite32 (INDIRECT_MAC_INDEX_MII_DATA, (Value & 0xFFFF));\r
\r
  // Now write the config to register\r
  IndirectMACWrite32 (INDIRECT_MAC_INDEX_MII_ACC, MiiAcc & 0xFFFF);\r
\r
  // Wait for operation to terminate\r
  while ((IndirectMACRead32 (INDIRECT_MAC_INDEX_MII_ACC) & MII_ACC_MII_BUSY) == MII_ACC_MII_BUSY);\r
\r
  return ValueWritten;\r
}\r
\r
\r
/* ---------------- EEPROM Operations ------------------ */\r
\r
\r
// Function to read from EEPROM memory\r
UINT32\r
IndirectEEPROMRead32 (\r
  UINT32 Index\r
  )\r
{\r
  UINT32 EepromCmd;\r
\r
  // Set the busy bit to ensure read will occur\r
  EepromCmd = E2P_EPC_BUSY | E2P_EPC_CMD_READ;\r
\r
  // Set the index to access desired EEPROM memory location\r
  EepromCmd |= E2P_EPC_ADDRESS(Index);\r
\r
  // Write to Eeprom command register\r
  MmioWrite32 (LAN9118_E2P_CMD, EepromCmd);\r
  gBS->Stall (LAN9118_STALL);\r
\r
  // Wait until operation has completed\r
  while (MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_BUSY);\r
\r
  // Check that operation didn't time out\r
  if (MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_TIMEOUT) {\r
    DEBUG ((EFI_D_ERROR, "EEPROM Operation Timed out: Read command on index %x\n",Index));\r
    return 0;\r
  }\r
\r
  // Wait until operation has completed\r
  while (MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_BUSY);\r
\r
  // Finally read the value\r
  return MmioRead32 (LAN9118_E2P_DATA);\r
}\r
\r
// Function to write to EEPROM memory\r
UINT32\r
IndirectEEPROMWrite32 (\r
  UINT32 Index,\r
  UINT32 Value\r
  )\r
{\r
  UINT32 ValueWritten;\r
  UINT32 EepromCmd;\r
\r
  ValueWritten = 0;\r
\r
  // Read the EEPROM Command register\r
  EepromCmd = MmioRead32 (LAN9118_E2P_CMD);\r
\r
  // Set the busy bit to ensure read will occur\r
  EepromCmd |= ((UINT32)1 << 31);\r
\r
  // Set the EEPROM command to write(0b011)\r
  EepromCmd &= ~(7 << 28);    // Clear the command first\r
  EepromCmd |= (3 << 28);     // Write 011\r
\r
  // Set the index to access desired EEPROM memory location\r
  EepromCmd |= (Index & 0xF);\r
\r
  // Write the value to the data register first\r
  ValueWritten = MmioWrite32 (LAN9118_E2P_DATA, Value);\r
\r
  // Write to Eeprom command register\r
  MmioWrite32 (LAN9118_E2P_CMD, EepromCmd);\r
  gBS->Stall (LAN9118_STALL);\r
\r
  // Wait until operation has completed\r
  while (MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_BUSY);\r
\r
  // Check that operation didn't time out\r
  if (MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_TIMEOUT) {\r
    DEBUG ((EFI_D_ERROR, "EEPROM Operation Timed out: Write command at memloc 0x%x, with value 0x%x\n",Index, Value));\r
    return 0;\r
  }\r
\r
  // Wait until operation has completed\r
  while (MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_BUSY);\r
\r
  return ValueWritten;\r
}\r
\r
/* ---------------- General Operations ----------------- */\r
\r
VOID\r
Lan9118SetMacAddress (\r
  EFI_MAC_ADDRESS             *Mac,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  IndirectMACWrite32 (INDIRECT_MAC_INDEX_ADDRL,\r
                      (Mac->Addr[0] & 0xFF) |\r
                      ((Mac->Addr[1] & 0xFF) << 8) |\r
                      ((Mac->Addr[2] & 0xFF) << 16) |\r
                      ((Mac->Addr[3] & 0xFF) << 24)\r
                    );\r
\r
  IndirectMACWrite32 (INDIRECT_MAC_INDEX_ADDRH,\r
                      (UINT32)(Mac->Addr[4] & 0xFF) |\r
                      ((Mac->Addr[5] & 0xFF) << 8)\r
                    );\r
}\r
\r
VOID\r
Lan9118ReadMacAddress (\r
  OUT EFI_MAC_ADDRESS *MacAddress\r
  )\r
{\r
  UINT32          MacAddrHighValue;\r
  UINT32          MacAddrLowValue;\r
\r
  // Read the Mac Addr high register\r
  MacAddrHighValue = (IndirectMACRead32 (INDIRECT_MAC_INDEX_ADDRH) & 0xFFFF);\r
  // Read the Mac Addr low register\r
  MacAddrLowValue = IndirectMACRead32 (INDIRECT_MAC_INDEX_ADDRL);\r
\r
  SetMem (MacAddress, sizeof(*MacAddress), 0);\r
  MacAddress->Addr[0] = (MacAddrLowValue & 0xFF);\r
  MacAddress->Addr[1] = (MacAddrLowValue & 0xFF00) >> 8;\r
  MacAddress->Addr[2] = (MacAddrLowValue & 0xFF0000) >> 16;\r
  MacAddress->Addr[3] = (MacAddrLowValue & 0xFF000000) >> 24;\r
  MacAddress->Addr[4] = (MacAddrHighValue & 0xFF);\r
  MacAddress->Addr[5] = (MacAddrHighValue & 0xFF00) >> 8;\r
}\r
\r
/*\r
 *  Power up the 9118 and find its MAC address.\r
 *\r
 *  This operation can be carried out when the LAN9118 is in any power state\r
 *\r
 */\r
EFI_STATUS\r
Lan9118Initialize (\r
  IN  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINTN  Timeout;\r
  UINT64 DefaultMacAddress;\r
\r
  // Attempt to wake-up the device if it is in a lower power state\r
  if (((MmioRead32 (LAN9118_PMT_CTRL) & MPTCTRL_PM_MODE_MASK) >> 12) != 0) {\r
    DEBUG ((DEBUG_NET, "Waking from reduced power state.\n"));\r
    MmioWrite32 (LAN9118_BYTE_TEST, 0xFFFFFFFF);\r
    gBS->Stall (LAN9118_STALL);\r
  }\r
\r
  // Check that device is active\r
  Timeout = 20;\r
  while ((MmioRead32 (LAN9118_PMT_CTRL) & MPTCTRL_READY) == 0 && --Timeout) {\r
    gBS->Stall (LAN9118_STALL);\r
  }\r
  if (!Timeout) {\r
    return EFI_TIMEOUT;\r
  }\r
\r
  // Check that EEPROM isn't active\r
  Timeout = 20;\r
  while ((MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_BUSY) && --Timeout){\r
    gBS->Stall (LAN9118_STALL);\r
  }\r
  if (!Timeout) {\r
    return EFI_TIMEOUT;\r
  }\r
\r
  // Check if a MAC address was loaded from EEPROM, and if it was, set it as the\r
  // current address.\r
  if ((MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_MAC_ADDRESS_LOADED) == 0) {\r
    DEBUG ((EFI_D_ERROR, "Warning: There was an error detecting EEPROM or loading the MAC Address.\n"));\r
\r
    // If we had an address before (set by StationAddess), continue to use it\r
    if (CompareMem (&Snp->Mode->CurrentAddress, &mZeroMac, NET_ETHER_ADDR_LEN)) {\r
      Lan9118SetMacAddress (&Snp->Mode->CurrentAddress, Snp);\r
    } else {\r
      // If there are no cached addresses, then fall back to a default\r
      DEBUG ((EFI_D_WARN, "Warning: using driver-default MAC address\n"));\r
      DefaultMacAddress = FixedPcdGet64 (PcdLan9118DefaultMacAddress);\r
      Lan9118SetMacAddress((EFI_MAC_ADDRESS *) &DefaultMacAddress, Snp);\r
      CopyMem (&Snp->Mode->CurrentAddress, &DefaultMacAddress, NET_ETHER_ADDR_LEN);\r
    }\r
  } else {\r
    // Store the MAC address that was loaded from EEPROM\r
    Lan9118ReadMacAddress (&Snp->Mode->CurrentAddress);\r
    CopyMem (&Snp->Mode->PermanentAddress, &Snp->Mode->CurrentAddress, NET_ETHER_ADDR_LEN);\r
  }\r
\r
  // Clear and acknowledge interrupts\r
  MmioWrite32 (LAN9118_INT_EN, 0);\r
  MmioWrite32 (LAN9118_IRQ_CFG, 0);\r
  MmioWrite32 (LAN9118_INT_STS, 0xFFFFFFFF);\r
\r
  // Do self tests here?\r
\r
  return EFI_SUCCESS;\r
}\r
\r
\r
// Perform software reset on the LAN9118\r
// Return 0 on success, -1 on error\r
EFI_STATUS\r
SoftReset (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 HwConf;\r
  UINT32 ResetTime;\r
\r
  // Initialize variable\r
  ResetTime = 0;\r
\r
  // Stop Rx and Tx\r
  StopTx (STOP_TX_MAC | STOP_TX_CFG | STOP_TX_CLEAR, Snp);\r
  StopRx (STOP_RX_CLEAR, Snp); // Clear receiver FIFO\r
\r
  // Issue the reset\r
  HwConf = MmioRead32 (LAN9118_HW_CFG);\r
  HwConf |= 1;\r
\r
  // Set the Must Be One (MBO) bit\r
  if (((HwConf & HWCFG_MBO) >> 20) == 0) {\r
    HwConf |= HWCFG_MBO;\r
  }\r
\r
  // Check that EEPROM isn't active\r
  while (MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_BUSY);\r
\r
  // Write the configuration\r
  MmioWrite32 (LAN9118_HW_CFG, HwConf);\r
  gBS->Stall (LAN9118_STALL);\r
\r
  // Wait for reset to complete\r
  while (MmioRead32 (LAN9118_HW_CFG) & HWCFG_SRST) {\r
\r
    gBS->Stall (LAN9118_STALL);\r
    ResetTime += 1;\r
\r
    // If time taken exceeds 100us, then there was an error condition\r
    if (ResetTime > 1000) {\r
      Snp->Mode->State = EfiSimpleNetworkStopped;\r
      return EFI_TIMEOUT;\r
    }\r
  }\r
\r
  // Check that EEPROM isn't active\r
  while (MmioRead32 (LAN9118_E2P_CMD) & E2P_EPC_BUSY);\r
\r
  // TODO we probably need to re-set the mac address here.\r
\r
  // Clear and acknowledge all interrupts\r
  if (Flags & SOFT_RESET_CLEAR_INT) {\r
    MmioWrite32 (LAN9118_INT_EN, 0);\r
    MmioWrite32 (LAN9118_IRQ_CFG, 0);\r
    MmioWrite32 (LAN9118_INT_STS, 0xFFFFFFFF);\r
  }\r
\r
  // Do self tests here?\r
  if (Flags & SOFT_RESET_SELF_TEST) {\r
\r
  }\r
\r
  return EFI_SUCCESS;\r
}\r
\r
\r
// Perform PHY software reset\r
EFI_STATUS\r
PhySoftReset (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 PmtCtrl = 0;\r
\r
  // PMT PHY reset takes precedence over BCR\r
  if (Flags & PHY_RESET_PMT) {\r
    PmtCtrl = MmioRead32 (LAN9118_PMT_CTRL);\r
    PmtCtrl |= MPTCTRL_PHY_RST;\r
    MmioWrite32 (LAN9118_PMT_CTRL,PmtCtrl);\r
\r
    // Wait for completion\r
    while (MmioRead32 (LAN9118_PMT_CTRL) & MPTCTRL_PHY_RST) {\r
      gBS->Stall (LAN9118_STALL);\r
    }\r
  // PHY Basic Control Register reset\r
  } else if (Flags & PHY_RESET_BCR) {\r
    IndirectPHYWrite32 (PHY_INDEX_BASIC_CTRL, PHYCR_RESET);\r
\r
    // Wait for completion\r
    while (IndirectPHYRead32 (PHY_INDEX_BASIC_CTRL) & PHYCR_RESET) {\r
      gBS->Stall (LAN9118_STALL);\r
    }\r
  }\r
\r
  // Clear and acknowledge all interrupts\r
  if (Flags & PHY_SOFT_RESET_CLEAR_INT) {\r
    MmioWrite32 (LAN9118_INT_EN, 0);\r
    MmioWrite32 (LAN9118_IRQ_CFG, 0);\r
    MmioWrite32 (LAN9118_INT_STS, 0xFFFFFFFF);\r
  }\r
\r
  return EFI_SUCCESS;\r
}\r
\r
\r
// Configure hardware for LAN9118\r
EFI_STATUS\r
ConfigureHardware (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 GpioConf;\r
\r
  // Check if we want to use LEDs on GPIO\r
  if (Flags & HW_CONF_USE_LEDS) {\r
    GpioConf = MmioRead32 (LAN9118_GPIO_CFG);\r
\r
    // Enable GPIO as LEDs and Config as Push-Pull driver\r
    GpioConf |= GPIO_GPIO0_PUSH_PULL | GPIO_GPIO1_PUSH_PULL | GPIO_GPIO2_PUSH_PULL |\r
                GPIO_LED1_ENABLE | GPIO_LED2_ENABLE | GPIO_LED3_ENABLE;\r
\r
    // Write the configuration\r
    MmioWrite32 (LAN9118_GPIO_CFG, GpioConf);\r
    gBS->Stall (LAN9118_STALL);\r
  }\r
\r
  return EFI_SUCCESS;\r
}\r
\r
// Configure flow control\r
EFI_STATUS\r
ConfigureFlow (\r
  UINT32 Flags,\r
  UINT32 HighTrig,\r
  UINT32 LowTrig,\r
  UINT32 BPDuration,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  return EFI_SUCCESS;\r
}\r
\r
// Do auto-negotiation\r
EFI_STATUS\r
AutoNegotiate (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 PhyControl;\r
  UINT32 PhyStatus;\r
  UINT32 Features;\r
  UINT32 TimeOut;\r
\r
  // First check that auto-negotiation is supported\r
  PhyStatus = IndirectPHYRead32 (PHY_INDEX_BASIC_STATUS);\r
  if ((PhyStatus & PHYSTS_AUTO_CAP) == 0) {\r
    DEBUG ((EFI_D_ERROR, "Auto-negotiation not supported.\n"));\r
    return EFI_DEVICE_ERROR;\r
  }\r
\r
  // Check that link is up first\r
  if ((PhyStatus & PHYSTS_LINK_STS) == 0) {\r
    // Wait until it is up or until Time Out\r
    TimeOut = 2000;\r
    while ((IndirectPHYRead32 (PHY_INDEX_BASIC_STATUS) & PHYSTS_LINK_STS) == 0) {\r
      gBS->Stall (LAN9118_STALL);\r
      TimeOut--;\r
      if (!TimeOut) {\r
        DEBUG ((EFI_D_ERROR, "Link timeout in auto-negotiation.\n"));\r
        return EFI_TIMEOUT;\r
      }\r
    }\r
  }\r
\r
  // Configure features to advertise\r
  Features = IndirectPHYRead32 (PHY_INDEX_AUTO_NEG_ADVERT);\r
\r
  if ((Flags & AUTO_NEGOTIATE_ADVERTISE_ALL) > 0) {\r
    // Link speed capabilities\r
    Features |= (PHYANA_10BASET | PHYANA_10BASETFD | PHYANA_100BASETX | PHYANA_100BASETXFD);\r
\r
    // Pause frame capabilities\r
    Features &= ~(PHYANA_PAUSE_OP_MASK);\r
    Features |= 3 << 10;\r
  }\r
\r
  // Write the features\r
  IndirectPHYWrite32 (PHY_INDEX_AUTO_NEG_ADVERT, Features);\r
\r
  // Read control register\r
  PhyControl = IndirectPHYRead32 (PHY_INDEX_BASIC_CTRL);\r
\r
  // Enable Auto-Negotiation\r
  if ((PhyControl & PHYCR_AUTO_EN) == 0) {\r
    PhyControl |= PHYCR_AUTO_EN;\r
  }\r
\r
  // Restart auto-negotiation\r
  PhyControl |= PHYCR_RST_AUTO;\r
\r
  // Enable collision test if required to do so\r
  if (Flags & AUTO_NEGOTIATE_COLLISION_TEST) {\r
    PhyControl |= PHYCR_COLL_TEST;\r
  } else {\r
    PhyControl &= ~ PHYCR_COLL_TEST;\r
  }\r
\r
  // Write this configuration\r
  IndirectPHYWrite32 (PHY_INDEX_BASIC_CTRL, PhyControl);\r
\r
  // Wait until process has completed\r
  while ((IndirectPHYRead32 (PHY_INDEX_BASIC_STATUS) & PHYSTS_AUTO_COMP) == 0);\r
\r
  return EFI_SUCCESS;\r
}\r
\r
// Check the Link Status and take appropriate action\r
EFI_STATUS\r
CheckLinkStatus (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  // Get the PHY Status\r
  UINT32 PhyBStatus = IndirectPHYRead32 (PHY_INDEX_BASIC_STATUS);\r
\r
  if (PhyBStatus & PHYSTS_LINK_STS) {\r
    return EFI_SUCCESS;\r
  } else {\r
    return EFI_DEVICE_ERROR;\r
  }\r
}\r
\r
// Stop the transmitter\r
EFI_STATUS\r
StopTx (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 MacCsr;\r
  UINT32 TxCfg;\r
\r
  MacCsr = 0;\r
  TxCfg = 0;\r
\r
  // Check if we want to clear tx\r
  if (Flags & STOP_TX_CLEAR) {\r
    TxCfg = MmioRead32 (LAN9118_TX_CFG);\r
    TxCfg |= TXCFG_TXS_DUMP | TXCFG_TXD_DUMP;\r
    MmioWrite32 (LAN9118_TX_CFG, TxCfg);\r
    gBS->Stall (LAN9118_STALL);\r
  }\r
\r
  // Check if already stopped\r
  if (Flags & STOP_TX_MAC) {\r
    MacCsr = IndirectMACRead32 (INDIRECT_MAC_INDEX_CR);\r
\r
    if (MacCsr & MACCR_TX_EN) {\r
      MacCsr &= ~MACCR_TX_EN;\r
      IndirectMACWrite32 (INDIRECT_MAC_INDEX_CR, MacCsr);\r
    }\r
  }\r
\r
  if (Flags & STOP_TX_CFG) {\r
    TxCfg = MmioRead32 (LAN9118_TX_CFG);\r
\r
    if (TxCfg & TXCFG_TX_ON) {\r
      TxCfg |= TXCFG_STOP_TX;\r
      MmioWrite32 (LAN9118_TX_CFG, TxCfg);\r
      gBS->Stall (LAN9118_STALL);\r
\r
      // Wait for Tx to finish transmitting\r
      while (MmioRead32 (LAN9118_TX_CFG) & TXCFG_STOP_TX);\r
    }\r
  }\r
\r
  return EFI_SUCCESS;\r
}\r
\r
// Stop the receiver\r
EFI_STATUS\r
StopRx (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 MacCsr;\r
  UINT32 RxCfg;\r
\r
  RxCfg = 0;\r
\r
  // Check if already stopped\r
  MacCsr = IndirectMACRead32 (INDIRECT_MAC_INDEX_CR);\r
\r
  if (MacCsr & MACCR_RX_EN) {\r
    MacCsr &= ~ MACCR_RX_EN;\r
    IndirectMACWrite32 (INDIRECT_MAC_INDEX_CR, MacCsr);\r
  }\r
\r
  // Check if we want to clear receiver FIFOs\r
  if (Flags & STOP_RX_CLEAR) {\r
    RxCfg = MmioRead32 (LAN9118_RX_CFG);\r
    RxCfg |= RXCFG_RX_DUMP;\r
    MmioWrite32 (LAN9118_RX_CFG, RxCfg);\r
    gBS->Stall (LAN9118_STALL);\r
\r
    while (MmioRead32 (LAN9118_RX_CFG) & RXCFG_RX_DUMP);\r
  }\r
\r
  return EFI_SUCCESS;\r
}\r
\r
// Start the transmitter\r
EFI_STATUS\r
StartTx (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 MacCsr;\r
  UINT32 TxCfg;\r
\r
  MacCsr = 0;\r
  TxCfg = 0;\r
\r
  // Check if we want to clear tx\r
  if (Flags & START_TX_CLEAR) {\r
    TxCfg = MmioRead32 (LAN9118_TX_CFG);\r
    TxCfg |= TXCFG_TXS_DUMP | TXCFG_TXD_DUMP;\r
    MmioWrite32 (LAN9118_TX_CFG, TxCfg);\r
    gBS->Stall (LAN9118_STALL);\r
  }\r
\r
  // Check if tx was started from MAC and enable if not\r
  if (Flags & START_TX_MAC) {\r
    MacCsr = IndirectMACRead32 (INDIRECT_MAC_INDEX_CR);\r
    gBS->Stall (LAN9118_STALL);\r
    if ((MacCsr & MACCR_TX_EN) == 0) {\r
      MacCsr |= MACCR_TX_EN;\r
      IndirectMACWrite32 (INDIRECT_MAC_INDEX_CR, MacCsr);\r
      gBS->Stall (LAN9118_STALL);\r
    }\r
  }\r
\r
  // Check if tx was started from TX_CFG and enable if not\r
  if (Flags & START_TX_CFG) {\r
    TxCfg = MmioRead32 (LAN9118_TX_CFG);\r
    gBS->Stall (LAN9118_STALL);\r
    if ((TxCfg & TXCFG_TX_ON) == 0) {\r
      TxCfg |= TXCFG_TX_ON;\r
      MmioWrite32 (LAN9118_TX_CFG, TxCfg);\r
      gBS->Stall (LAN9118_STALL);\r
    }\r
  }\r
\r
  // Set the tx data trigger level\r
\r
  return EFI_SUCCESS;\r
}\r
\r
// Start the receiver\r
EFI_STATUS\r
StartRx (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 MacCsr;\r
  UINT32 RxCfg;\r
\r
  RxCfg = 0;\r
\r
  // Check if already started\r
  MacCsr = IndirectMACRead32 (INDIRECT_MAC_INDEX_CR);\r
\r
  if ((MacCsr & MACCR_RX_EN) == 0) {\r
    // Check if we want to clear receiver FIFOs before starting\r
    if (Flags & START_RX_CLEAR) {\r
      RxCfg = MmioRead32 (LAN9118_RX_CFG);\r
      RxCfg |= RXCFG_RX_DUMP;\r
      MmioWrite32 (LAN9118_RX_CFG, RxCfg);\r
      gBS->Stall (LAN9118_STALL);\r
\r
      while (MmioRead32 (LAN9118_RX_CFG) & RXCFG_RX_DUMP);\r
    }\r
\r
    MacCsr |= MACCR_RX_EN;\r
    IndirectMACWrite32 (INDIRECT_MAC_INDEX_CR, MacCsr);\r
    gBS->Stall (LAN9118_STALL);\r
  }\r
\r
  return EFI_SUCCESS;\r
}\r
\r
// Check Tx Data available space\r
UINT32\r
TxDataFreeSpace (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 TxInf;\r
  UINT32 FreeSpace;\r
\r
  // Get the amount of free space from information register\r
  TxInf = MmioRead32 (LAN9118_TX_FIFO_INF);\r
  FreeSpace = (TxInf & TXFIFOINF_TDFREE_MASK);\r
\r
  return FreeSpace; // Value in bytes\r
}\r
\r
// Check Tx Status used space\r
UINT32\r
TxStatusUsedSpace (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 TxInf;\r
  UINT32 UsedSpace;\r
\r
  // Get the amount of used space from information register\r
  TxInf = MmioRead32 (LAN9118_TX_FIFO_INF);\r
  UsedSpace = (TxInf & TXFIFOINF_TXSUSED_MASK) >> 16;\r
\r
  return UsedSpace << 2; // Value in bytes\r
}\r
\r
// Check Rx Data used space\r
UINT32\r
RxDataUsedSpace (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 RxInf;\r
  UINT32 UsedSpace;\r
\r
  // Get the amount of used space from information register\r
  RxInf = MmioRead32 (LAN9118_RX_FIFO_INF);\r
  UsedSpace = (RxInf & RXFIFOINF_RXDUSED_MASK);\r
\r
  return UsedSpace; // Value in bytes (rounded up to nearest DWORD)\r
}\r
\r
// Check Rx Status used space\r
UINT32\r
RxStatusUsedSpace (\r
  UINT32 Flags,\r
  EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 RxInf;\r
  UINT32 UsedSpace;\r
\r
  // Get the amount of used space from information register\r
  RxInf = MmioRead32 (LAN9118_RX_FIFO_INF);\r
  UsedSpace = (RxInf & RXFIFOINF_RXSUSED_MASK) >> 16;\r
\r
  return UsedSpace << 2; // Value in bytes\r
}\r
\r
\r
// Change the allocation of FIFOs\r
EFI_STATUS\r
ChangeFifoAllocation (\r
  IN      UINT32 Flags,\r
  IN  OUT UINTN  *TxDataSize    OPTIONAL,\r
  IN  OUT UINTN  *RxDataSize    OPTIONAL,\r
  IN  OUT UINT32 *TxStatusSize  OPTIONAL,\r
  IN  OUT UINT32 *RxStatusSize  OPTIONAL,\r
  IN  OUT EFI_SIMPLE_NETWORK_PROTOCOL *Snp\r
  )\r
{\r
  UINT32 HwConf;\r
  UINT32 TxFifoOption;\r
\r
  // Check that desired sizes don't exceed limits\r
  if (*TxDataSize > TX_FIFO_MAX_SIZE)\r
    return EFI_INVALID_PARAMETER;\r
\r
#if defined(RX_FIFO_MIN_SIZE) && defined(RX_FIFO_MAX_SIZE)\r
  if (*RxDataSize > RX_FIFO_MAX_SIZE) {\r
    return EFI_INVALID_PARAMETER;\r
  }\r
#endif\r
\r
  if (Flags & ALLOC_USE_DEFAULT) {\r
    return EFI_SUCCESS;\r
  }\r
\r
  // If we use the FIFOs (always use this first)\r
  if (Flags & ALLOC_USE_FIFOS) {\r
    // Read the current value of allocation\r
    HwConf = MmioRead32 (LAN9118_HW_CFG);\r
    TxFifoOption = (HwConf >> 16) & 0xF;\r
\r
    // Choose the correct size (always use larger than requested if possible)\r
    if (*TxDataSize < TX_FIFO_MIN_SIZE) {\r
      *TxDataSize = TX_FIFO_MIN_SIZE;\r
      *RxDataSize = 13440;\r
      *RxStatusSize = 896;\r
      TxFifoOption = 2;\r
    } else if ((*TxDataSize > TX_FIFO_MIN_SIZE) && (*TxDataSize <= 2560)) {\r
      *TxDataSize = 2560;\r
      *RxDataSize = 12480;\r
      *RxStatusSize = 832;\r
      TxFifoOption = 3;\r
    } else if ((*TxDataSize > 2560) && (*TxDataSize <= 3584)) {\r
      *TxDataSize = 3584;\r
      *RxDataSize = 11520;\r
      *RxStatusSize = 768;\r
      TxFifoOption = 4;\r
    } else if ((*TxDataSize > 3584) && (*TxDataSize <= 4608)) { // default option\r
      *TxDataSize = 4608;\r
      *RxDataSize = 10560;\r
      *RxStatusSize = 704;\r
      TxFifoOption = 5;\r
    } else if ((*TxDataSize > 4608) && (*TxDataSize <= 5632)) {\r
      *TxDataSize = 5632;\r
      *RxDataSize = 9600;\r
      *RxStatusSize = 640;\r
      TxFifoOption = 6;\r
    } else if ((*TxDataSize > 5632) && (*TxDataSize <= 6656)) {\r
      *TxDataSize = 6656;\r
      *RxDataSize = 8640;\r
      *RxStatusSize = 576;\r
      TxFifoOption = 7;\r
    } else if ((*TxDataSize > 6656) && (*TxDataSize <= 7680)) {\r
      *TxDataSize = 7680;\r
      *RxDataSize = 7680;\r
      *RxStatusSize = 512;\r
      TxFifoOption = 8;\r
    } else if ((*TxDataSize > 7680) && (*TxDataSize <= 8704)) {\r
      *TxDataSize = 8704;\r
      *RxDataSize = 6720;\r
      *RxStatusSize = 448;\r
      TxFifoOption = 9;\r
    } else if ((*TxDataSize > 8704) && (*TxDataSize <= 9728)) {\r
      *TxDataSize = 9728;\r
      *RxDataSize = 5760;\r
      *RxStatusSize = 384;\r
      TxFifoOption = 10;\r
    } else if ((*TxDataSize > 9728) && (*TxDataSize <= 10752)) {\r
      *TxDataSize = 10752;\r
      *RxDataSize = 4800;\r
      *RxStatusSize = 320;\r
      TxFifoOption = 11;\r
    } else if ((*TxDataSize > 10752) && (*TxDataSize <= 11776)) {\r
      *TxDataSize = 11776;\r
      *RxDataSize = 3840;\r
      *RxStatusSize = 256;\r
      TxFifoOption = 12;\r
    } else if ((*TxDataSize > 11776) && (*TxDataSize <= 12800)) {\r
      *TxDataSize = 12800;\r
      *RxDataSize = 2880;\r
      *RxStatusSize = 192;\r
      TxFifoOption = 13;\r
    } else if ((*TxDataSize > 12800) && (*TxDataSize <= 13824)) {\r
      *TxDataSize = 13824;\r
      *RxDataSize = 1920;\r
      *RxStatusSize = 128;\r
      TxFifoOption = 14;\r
    }\r
  } else {\r
    ASSERT(0); // Untested code path\r
    HwConf = 0;\r
    TxFifoOption = 0;\r
  }\r
\r
  // Do we need DMA?\r
  if (Flags & ALLOC_USE_DMA) {\r
    return EFI_UNSUPPORTED; // Unsupported as of now\r
  }\r
  // Clear and assign the new size option\r
  HwConf &= ~(0xF0000);\r
  HwConf |= ((TxFifoOption & 0xF) << 16);\r
  MmioWrite32 (LAN9118_HW_CFG, HwConf);\r
  gBS->Stall (LAN9118_STALL);\r
\r
  return EFI_SUCCESS;\r
}\r