## @file # Network DSC include file for [Defines] section of all Architectures. # # This file can be included to the [Defines] section of a platform DSC file by # using "!include NetworkPkg/NetworkDefines.dsc.inc" to set default value of # flags if they are not defined somewhere else, and also check the value to see # if there is any conflict. # # These flags can be defined before the !include line, or changed on the command # line to enable or disable related feature support. # -D FLAG=VALUE # The default value of these flags are: # DEFINE NETWORK_ENABLE = TRUE # DEFINE NETWORK_SNP_ENABLE = TRUE # DEFINE NETWORK_IP4_ENABLE = TRUE # DEFINE NETWORK_IP6_ENABLE = TRUE # DEFINE NETWORK_TLS_ENABLE = TRUE # DEFINE NETWORK_HTTP_BOOT_ENABLE = TRUE # DEFINE NETWORK_ALLOW_HTTP_CONNECTIONS = FALSE # DEFINE NETWORK_ISCSI_ENABLE = FALSE # DEFINE NETWORK_VLAN_ENABLE = TRUE # # Copyright (c) 2019, Intel Corporation. All rights reserved.
# # SPDX-License-Identifier: BSD-2-Clause-Patent # ## !ifndef NETWORK_ENABLE # # This flag is to enable or disable the whole network stack. # DEFINE NETWORK_ENABLE = TRUE !endif !ifndef NETWORK_SNP_ENABLE # # This flag is to include the common SNP driver or not. # DEFINE NETWORK_SNP_ENABLE = TRUE !endif !ifndef NETWORK_VLAN_ENABLE # # This flag is to enable or disable VLAN feature. # DEFINE NETWORK_VLAN_ENABLE = TRUE !endif !ifndef NETWORK_IP4_ENABLE # # This flag is to enable or disable IPv4 network stack. # DEFINE NETWORK_IP4_ENABLE = TRUE !endif !ifndef NETWORK_IP6_ENABLE # # This flag is to enable or disable IPv6 network stack. # DEFINE NETWORK_IP6_ENABLE = TRUE !endif !ifndef NETWORK_TLS_ENABLE # # This flag is to enable or disable TLS feature. # # Note: This feature depends on the OpenSSL building. To enable this feature, please # follow the instructions found in the file "OpenSSL-HOWTO.txt" located in # CryptoPkg\Library\OpensslLib to enable the OpenSSL building first. # The OpensslLib.inf library instance should be used since libssl is required. # DEFINE NETWORK_TLS_ENABLE = TRUE !endif !ifndef NETWORK_HTTP_BOOT_ENABLE # # This flag is to enable or disable HTTP(S) boot feature. # DEFINE NETWORK_HTTP_BOOT_ENABLE = TRUE !endif !ifndef NETWORK_ALLOW_HTTP_CONNECTIONS # # Indicates whether HTTP connections (i.e., unsecured) are permitted or not. # # Note: If NETWORK_ALLOW_HTTP_CONNECTIONS is TRUE, HTTP connections are allowed. # Both the "https://" and "http://" URI schemes are permitted. Otherwise, HTTP # connections are denied. Only the "https://" URI scheme is permitted. # DEFINE NETWORK_ALLOW_HTTP_CONNECTIONS = FALSE !endif !ifndef NETWORK_ISCSI_ENABLE # # This flag is to enable or disable iSCSI feature. # # Note: This feature depends on the OpenSSL building. To enable this feature, please # follow the instructions found in the file "OpenSSL-HOWTO.txt" located in # CryptoPkg\Library\OpensslLib to enable the OpenSSL building first. # Both OpensslLib.inf and OpensslLibCrypto.inf library instance can be used # since libssl is not required for iSCSI. # DEFINE NETWORK_ISCSI_ENABLE = FALSE !endif !if $(NETWORK_ENABLE) == TRUE # # Check the flags to see if there is any conflict. # !if ($(NETWORK_IP4_ENABLE) == FALSE) AND ($(NETWORK_IP6_ENABLE) == FALSE) !error "Must enable at least IP4 or IP6 stack if NETWORK_ENABLE is set to TRUE!" !endif !if ($(NETWORK_HTTP_BOOT_ENABLE) == TRUE) AND ($(NETWORK_TLS_ENABLE) == FALSE) AND ($(NETWORK_ALLOW_HTTP_CONNECTIONS) == FALSE) !error "Must enable TLS to support HTTPS, or allow unsecured HTTP connection, if NETWORK_HTTP_BOOT_ENABLE is set to TRUE!" !endif !endif