================================================================================ Build And Integration Instructions 2019 March 27th ================================================================================ ================================================================================ DISCLAIMER ================================================================================ This release note as well as the software described in it is furnished under license and may only be used or copied in accordance with the terms of the license. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Intel Corporation. Intel Corporation assumes no responsibility or liability for any errors or inaccuracies that may appear in this document or any software that may be provided in association with this document. Except as permitted by such license, no part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means without the express written consent of Intel Corporation. ================================================================================ INDEX ================================================================================ A. INTRODUCTION B. HOW TO BUILD C. HOW TO INTEGRATE INTO COREBOOT D. HOW TO INTEGRATE INTO SLIM BOOTLOADER ================================================================================ A. INTRODUCTION ================================================================================ This document provides instructions on how to build UEFI Payload and how to integrate it into coreboot or Slim Bootloader firmware. ================================================================================ B. HOW TO BUILD ================================================================================ 1. Run the below two commands in windows command prompt window: edksetup.bat For debug ia32 build: build -a IA32 -p UefiPayloadPkg\UefiPayloadPkgIa32.dsc -b DEBUG -t -D BOOTLOADER= For release ia32 build: build -a IA32 -p UefiPayloadPkg\UefiPayloadPkgIa32.dsc -b RELEASE -t -D BOOTLOADER= For debug X64 build: build -a IA32 -a X64 -p UefiPayloadPkg\UefiPayloadPkgIa32X64.dsc -b DEBUG -t -D BOOTLOADER= For release X64 build: build -a IA32 -a X64 -p UefiPayloadPkg\UefiPayloadPkgIa32X64.dsc -b RELEASE -t -D BOOTLOADER= is the EDK II build environment on your host. Currently it was tested with VS2015x86 toolchain. could be "SBL" for Slim Bootloader and "COREBOOT" for coreboot. Refer to https://github.com/tianocore/tianocore.github.io/wiki/UDK2018-How-to-Build for details about EDK II build steps. 2. If build is successfully, the payload image (UEFIPAYLOAD.fd) will be generated inside the folder of Build\UefiPayloadPkg. ================================================================================ C. HOW TO INTEGRATE INTO COREBOOT ================================================================================ 1. Copy the payload image (UEFIPAYLOAD.fd) into the top-level directory of Coreboot source tree. 2. Run "make menuconfig" in linux console to start Coreboot configuration surface. 3. In the Payload section, 1) Choose "An ELF executable payload" for the option of "Add a payload". 2) Type the path of payload image for the option of "Payload path and filename". 3) Select the option of "Use LZMA compression for payloads". 4. If the graphics console is required in UEFI payload, enable framebuffer initialization in coreboot. This could be done by enabling native graphics or using VGA BIOS option rom. 5. Build the coreboot firmware image. ================================================================================ D. HOW TO INTEGRATE INTO SLIM BOOTLOADER ================================================================================ Please refer https://slimbootloader.github.io/how-tos/integrate-multiple-payloads.html for below steps. 1. Copy the payload image (UEFIPAYLOAD.fd) into Slim Bootloader source at PayloadPkg\PayloadBins\UefiPld.fd 2. Update config data to make UEFI payload as default payload if required. 3. Build Slim Bootloader with UEFI payload: BuildLoader.py build -p "OsLoader.efi:LLDR:Lz4;UefiPld.fd:UEFI:Lzma"