--- /dev/null
+/** @file\r
+*\r
+* Copyright (c) 2011-2016, ARM Limited. All rights reserved.\r
+*\r
+* This program and the accompanying materials\r
+* are licensed and made available under the terms and conditions of the BSD License\r
+* which accompanies this distribution. The full text of the license may be found at\r
+* http://opensource.org/licenses/bsd-license.php\r
+*\r
+* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,\r
+* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.\r
+*\r
+**/\r
+\r
+#ifndef __PL011_UART_LIB_H__\r
+#define __PL011_UART_LIB_H__\r
+\r
+#include <Uefi/UefiBaseType.h>\r
+\r
+#include <Protocol/SerialIo.h>\r
+\r
+/**\r
+\r
+ Initialise the serial port to the specified settings.\r
+ All unspecified settings will be set to the default values.\r
+\r
+ @param[in] UartBase The base address of the serial device.\r
+ @param[in] UartClkInHz The clock in Hz for the serial device.\r
+ Ignored if the PCD PL011UartInteger is not 0\r
+ @param[in out] BaudRate The baud rate of the serial device. If the\r
+ baud rate is not supported, the speed will be\r
+ reduced to the nearest supported one and the\r
+ variable's value will be updated accordingly.\r
+ @param[in out] ReceiveFifoDepth The number of characters the device will\r
+ buffer on input. Value of 0 will use the\r
+ device's default FIFO depth.\r
+ @param[in out] Parity If applicable, this is the EFI_PARITY_TYPE\r
+ that is computed or checked as each character\r
+ is transmitted or received. If the device\r
+ does not support parity, the value is the\r
+ default parity value.\r
+ @param[in out] DataBits The number of data bits in each character.\r
+ @param[in out] StopBits If applicable, the EFI_STOP_BITS_TYPE number\r
+ of stop bits per character.\r
+ If the device does not support stop bits, the\r
+ value is the default stop bit value.\r
+\r
+ @retval RETURN_SUCCESS All attributes were set correctly on the\r
+ serial device.\r
+ @retval RETURN_INVALID_PARAMETER One or more of the attributes has an\r
+ unsupported value.\r
+\r
+**/\r
+RETURN_STATUS\r
+EFIAPI\r
+PL011UartInitializePort (\r
+ IN UINTN UartBase,\r
+ IN UINT32 UartClkInHz,\r
+ IN OUT UINT64 *BaudRate,\r
+ IN OUT UINT32 *ReceiveFifoDepth,\r
+ IN OUT EFI_PARITY_TYPE *Parity,\r
+ IN OUT UINT8 *DataBits,\r
+ IN OUT EFI_STOP_BITS_TYPE *StopBits\r
+ );\r
+\r
+/**\r
+\r
+ Assert or deassert the control signals on a serial port.\r
+ The following control signals are set according their bit settings :\r
+ . Request to Send\r
+ . Data Terminal Ready\r
+\r
+ @param[in] UartBase UART registers base address\r
+ @param[in] Control The following bits are taken into account :\r
+ . EFI_SERIAL_REQUEST_TO_SEND : assert/deassert the\r
+ "Request To Send" control signal if this bit is\r
+ equal to one/zero.\r
+ . EFI_SERIAL_DATA_TERMINAL_READY : assert/deassert\r
+ the "Data Terminal Ready" control signal if this\r
+ bit is equal to one/zero.\r
+ . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : enable/disable\r
+ the hardware loopback if this bit is equal to\r
+ one/zero.\r
+ . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : not supported.\r
+ . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : enable/\r
+ disable the hardware flow control based on CTS (Clear\r
+ To Send) and RTS (Ready To Send) control signals.\r
+\r
+ @retval RETURN_SUCCESS The new control bits were set on the device.\r
+ @retval RETURN_UNSUPPORTED The device does not support this operation.\r
+\r
+**/\r
+RETURN_STATUS\r
+EFIAPI\r
+PL011UartSetControl (\r
+ IN UINTN UartBase,\r
+ IN UINT32 Control\r
+ );\r
+\r
+/**\r
+\r
+ Retrieve the status of the control bits on a serial device.\r
+\r
+ @param[in] UartBase UART registers base address\r
+ @param[out] Control Status of the control bits on a serial device :\r
+\r
+ . EFI_SERIAL_DATA_CLEAR_TO_SEND,\r
+ EFI_SERIAL_DATA_SET_READY,\r
+ EFI_SERIAL_RING_INDICATE,\r
+ EFI_SERIAL_CARRIER_DETECT,\r
+ EFI_SERIAL_REQUEST_TO_SEND,\r
+ EFI_SERIAL_DATA_TERMINAL_READY\r
+ are all related to the DTE (Data Terminal Equipment)\r
+ and DCE (Data Communication Equipment) modes of\r
+ operation of the serial device.\r
+ . EFI_SERIAL_INPUT_BUFFER_EMPTY : equal to one if the\r
+ receive buffer is empty, 0 otherwise.\r
+ . EFI_SERIAL_OUTPUT_BUFFER_EMPTY : equal to one if the\r
+ transmit buffer is empty, 0 otherwise.\r
+ . EFI_SERIAL_HARDWARE_LOOPBACK_ENABLE : equal to one if\r
+ the hardware loopback is enabled (the ouput feeds the\r
+ receive buffer), 0 otherwise.\r
+ . EFI_SERIAL_SOFTWARE_LOOPBACK_ENABLE : equal to one if\r
+ a loopback is accomplished by software, 0 otherwise.\r
+ . EFI_SERIAL_HARDWARE_FLOW_CONTROL_ENABLE : equal to\r
+ one if the hardware flow control based on CTS (Clear\r
+ To Send) and RTS (Ready To Send) control signals is\r
+ enabled, 0 otherwise.\r
+\r
+ @retval RETURN_SUCCESS The control bits were read from the serial device.\r
+\r
+**/\r
+RETURN_STATUS\r
+EFIAPI\r
+PL011UartGetControl (\r
+ IN UINTN UartBase,\r
+ OUT UINT32 *Control\r
+ );\r
+\r
+/**\r
+ Write data to serial device.\r
+\r
+ @param Buffer Point of data buffer which need to be written.\r
+ @param NumberOfBytes Number of output bytes which are cached in Buffer.\r
+\r
+ @retval 0 Write data failed.\r
+ @retval !0 Actual number of bytes written to serial device.\r
+\r
+**/\r
+UINTN\r
+EFIAPI\r
+PL011UartWrite (\r
+ IN UINTN UartBase,\r
+ IN UINT8 *Buffer,\r
+ IN UINTN NumberOfBytes\r
+ );\r
+\r
+/**\r
+ Read data from serial device and save the data in buffer.\r
+\r
+ @param Buffer Point of data buffer which need to be written.\r
+ @param NumberOfBytes Number of output bytes which are cached in Buffer.\r
+\r
+ @retval 0 Read data failed.\r
+ @retval !0 Actual number of bytes read from serial device.\r
+\r
+**/\r
+UINTN\r
+EFIAPI\r
+PL011UartRead (\r
+ IN UINTN UartBase,\r
+ OUT UINT8 *Buffer,\r
+ IN UINTN NumberOfBytes\r
+ );\r
+\r
+/**\r
+ Check to see if any data is available to be read from the debug device.\r
+\r
+ @retval TRUE At least one byte of data is available to be read\r
+ @retval FALSE No data is available to be read\r
+\r
+**/\r
+BOOLEAN\r
+EFIAPI\r
+PL011UartPoll (\r
+ IN UINTN UartBase\r
+ );\r
+\r
+#endif\r
projects / mirror_edk2.git / blobdiff