+++ /dev/null
-/*++\r
-\r
-Copyright (c) 2006, Intel Corporation \r
-All rights reserved. This program and the accompanying materials \r
-are licensed and made available under the terms and conditions of the BSD License \r
-which accompanies this distribution. The full text of the license may be found at \r
-http://opensource.org/licenses/bsd-license.php \r
- \r
-THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, \r
-WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. \r
-\r
-Module Name:\r
- \r
- \r
- E100B.C\r
-\r
-Abstract:\r
-\r
-\r
-Revision History\r
-\r
---*/\r
-\r
-#include "Undi32.h"\r
-\r
-static UINT8 basic_config_cmd[22] = {\r
- 22, 0x08,\r
- 0, 0,\r
- 0, (UINT8)0x80,\r
- 0x32, 0x03,\r
- 1, 0,\r
- 0x2E, 0,\r
- 0x60, 0,\r
- (UINT8)0xf2, 0x48,\r
- 0, 0x40,\r
- (UINT8)0xf2, (UINT8)0x80, // 0x40=Force full-duplex \r
- 0x3f, 0x05,\r
-};\r
-\r
-//\r
-// How to wait for the command unit to accept a command.\r
-// Typically this takes 0 ticks.\r
-//\r
-#define wait_for_cmd_done(cmd_ioaddr) \\r
-{ \\r
- INT16 wait_count = 2000; \\r
- while ((InByte (AdapterInfo, cmd_ioaddr) != 0) && --wait_count >= 0) \\r
- DelayIt (AdapterInfo, 10); \\r
- if (wait_count == 0) \\r
- DelayIt (AdapterInfo, 50); \\r
-}\r
-\r
-UINT8\r
-InByte (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT32 Port\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This function calls the MemIo callback to read a byte from the device's\r
- address space\r
- Since UNDI3.0 uses the TmpMemIo function (instead of the callback routine)\r
- which also takes the UniqueId parameter (as in UNDI3.1 spec) we don't have \r
- to make undi3.0 a special case\r
- \r
-Arguments:\r
- Port - Which port to read from.\r
-\r
-Returns:\r
- Results - The data read from the port.\r
-\r
---*/\r
-// TODO: AdapterInfo - add argument and description to function comment\r
-{\r
- UINT8 Results;\r
-\r
- (*AdapterInfo->Mem_Io) (\r
- AdapterInfo->Unique_ID, \r
- PXE_MEM_READ, \r
- 1, \r
- (UINT64)Port,\r
- (UINT64) (UINTN) &Results\r
- );\r
- return Results;\r
-}\r
-\r
-UINT16\r
-InWord (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT32 Port\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This function calls the MemIo callback to read a word from the device's\r
- address space\r
- Since UNDI3.0 uses the TmpMemIo function (instead of the callback routine)\r
- which also takes the UniqueId parameter (as in UNDI3.1 spec) we don't have \r
- to make undi3.0 a special case\r
-\r
-Arguments:\r
- Port - Which port to read from.\r
-\r
-Returns:\r
- Results - The data read from the port.\r
-\r
---*/\r
-// TODO: AdapterInfo - add argument and description to function comment\r
-{\r
- UINT16 Results;\r
-\r
- (*AdapterInfo->Mem_Io) (\r
- AdapterInfo->Unique_ID,\r
- PXE_MEM_READ,\r
- 2,\r
- (UINT64)Port,\r
- (UINT64)(UINTN)&Results\r
- );\r
- return Results;\r
-}\r
-\r
-UINT32\r
-InLong (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT32 Port\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This function calls the MemIo callback to read a dword from the device's\r
- address space\r
- Since UNDI3.0 uses the TmpMemIo function (instead of the callback routine)\r
- which also takes the UniqueId parameter (as in UNDI3.1 spec) we don't have \r
- to make undi3.0 a special case\r
-\r
-Arguments:\r
- Port - Which port to read from.\r
-\r
-Returns:\r
- Results - The data read from the port.\r
-\r
---*/\r
-// TODO: AdapterInfo - add argument and description to function comment\r
-{\r
- UINT32 Results;\r
-\r
- (*AdapterInfo->Mem_Io) (\r
- AdapterInfo->Unique_ID,\r
- PXE_MEM_READ,\r
- 4,\r
- (UINT64)Port,\r
- (UINT64)(UINTN)&Results\r
- );\r
- return Results;\r
-}\r
-\r
-VOID\r
-OutByte (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT8 Data,\r
- IN UINT32 Port\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This function calls the MemIo callback to write a byte from the device's\r
- address space\r
- Since UNDI3.0 uses the TmpMemIo function (instead of the callback routine)\r
- which also takes the UniqueId parameter (as in UNDI3.1 spec) we don't have \r
- to make undi3.0 a special case\r
-\r
-Arguments:\r
- Data - Data to write to Port.\r
- Port - Which port to write to.\r
-\r
-Returns:\r
- none\r
-\r
---*/\r
-// TODO: AdapterInfo - add argument and description to function comment\r
-{\r
- UINT8 Val;\r
-\r
- Val = Data;\r
- (*AdapterInfo->Mem_Io) (\r
- AdapterInfo->Unique_ID,\r
- PXE_MEM_WRITE,\r
- 1,\r
- (UINT64)Port,\r
- (UINT64)(UINTN)(UINTN)&Val\r
- );\r
- return ;\r
-}\r
-\r
-VOID\r
-OutWord (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT16 Data,\r
- IN UINT32 Port\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This function calls the MemIo callback to write a word from the device's\r
- address space\r
- Since UNDI3.0 uses the TmpMemIo function (instead of the callback routine)\r
- which also takes the UniqueId parameter (as in UNDI3.1 spec) we don't have \r
- to make undi3.0 a special case\r
-\r
-Arguments:\r
- Data - Data to write to Port.\r
- Port - Which port to write to.\r
-\r
-Returns:\r
- none\r
-\r
---*/\r
-// TODO: AdapterInfo - add argument and description to function comment\r
-{\r
- UINT16 Val;\r
-\r
- Val = Data;\r
- (*AdapterInfo->Mem_Io) (\r
- AdapterInfo->Unique_ID,\r
- PXE_MEM_WRITE,\r
- 2,\r
- (UINT64)Port,\r
- (UINT64)(UINTN)&Val\r
- );\r
- return ;\r
-}\r
-\r
-VOID\r
-OutLong (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT32 Data,\r
- IN UINT32 Port\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This function calls the MemIo callback to write a dword from the device's\r
- address space\r
- Since UNDI3.0 uses the TmpMemIo function (instead of the callback routine)\r
- which also takes the UniqueId parameter (as in UNDI3.1 spec) we don't have \r
- to make undi3.0 a special case\r
-\r
-Arguments:\r
- Data - Data to write to Port.\r
- Port - Which port to write to.\r
-\r
-Returns:\r
- none\r
-\r
---*/\r
-// TODO: AdapterInfo - add argument and description to function comment\r
-{\r
- UINT32 Val;\r
-\r
- Val = Data;\r
- (*AdapterInfo->Mem_Io) (\r
- AdapterInfo->Unique_ID,\r
- PXE_MEM_WRITE,\r
- 4,\r
- (UINT64)Port,\r
- (UINT64)(UINTN)&Val\r
- );\r
- return ;\r
-}\r
-\r
-STATIC\r
-UINTN\r
-MapIt (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT64 MemAddr,\r
- IN UINT32 Size,\r
- IN UINT32 Direction,\r
- OUT UINT64 MappedAddr\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- MemAddr - TODO: add argument description\r
- Size - TODO: add argument description\r
- Direction - TODO: add argument description\r
- MappedAddr - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- UINT64 *PhyAddr;\r
-\r
- PhyAddr = (UINT64 *) (UINTN) MappedAddr;\r
- //\r
- // mapping is different for theold and new NII protocols\r
- //\r
- if (AdapterInfo->VersionFlag == 0x30) {\r
- if (AdapterInfo->Virt2Phys_30 == (VOID *) NULL) {\r
- *PhyAddr = (UINT64) AdapterInfo->MemoryPtr;\r
- } else {\r
- (*AdapterInfo->Virt2Phys_30) (MemAddr, (UINT64) (UINTN) PhyAddr);\r
- }\r
-\r
- if (*PhyAddr > FOUR_GIGABYTE) {\r
- return PXE_STATCODE_INVALID_PARAMETER;\r
- }\r
- } else {\r
- if (AdapterInfo->Map_Mem == (VOID *) NULL) {\r
- //\r
- // this UNDI cannot handle addresses beyond 4 GB without a map routine\r
- //\r
- if (MemAddr > FOUR_GIGABYTE) {\r
- return PXE_STATCODE_INVALID_PARAMETER;\r
- } else {\r
- *PhyAddr = MemAddr;\r
- }\r
- } else {\r
- (*AdapterInfo->Map_Mem) (\r
- AdapterInfo->Unique_ID,\r
- MemAddr,\r
- Size,\r
- Direction,\r
- MappedAddr\r
- );\r
- }\r
- }\r
-\r
- return PXE_STATCODE_SUCCESS;\r
-}\r
-\r
-STATIC\r
-VOID\r
-UnMapIt (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT64 MemAddr,\r
- IN UINT32 Size,\r
- IN UINT32 Direction,\r
- IN UINT64 MappedAddr\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- MemAddr - TODO: add argument description\r
- Size - TODO: add argument description\r
- Direction - TODO: add argument description\r
- MappedAddr - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- if (AdapterInfo->VersionFlag > 0x30) {\r
- //\r
- // no mapping service\r
- //\r
- if (AdapterInfo->UnMap_Mem != (VOID *) NULL) {\r
- (*AdapterInfo->UnMap_Mem) (\r
- AdapterInfo->Unique_ID,\r
- MemAddr,\r
- Size,\r
- Direction,\r
- MappedAddr\r
- );\r
-\r
- }\r
- }\r
-\r
- return ;\r
-}\r
-\r
-STATIC\r
-VOID\r
-DelayIt (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- UINT16 MicroSeconds\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information\r
- which the UNDI driver is layering on..\r
-\r
-Returns:\r
-\r
---*/\r
-// TODO: MicroSeconds - add argument and description to function comment\r
-{\r
- if (AdapterInfo->VersionFlag == 0x30) {\r
- (*AdapterInfo->Delay_30) (MicroSeconds);\r
- } else {\r
- (*AdapterInfo->Delay) (AdapterInfo->Unique_ID, MicroSeconds);\r
- }\r
-}\r
-\r
-STATIC\r
-VOID\r
-BlockIt (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- UINT32 flag\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information\r
- which the UNDI driver is layering on..\r
-\r
-Returns:\r
-\r
---*/\r
-// TODO: flag - add argument and description to function comment\r
-{\r
- if (AdapterInfo->VersionFlag == 0x30) {\r
- (*AdapterInfo->Block_30) (flag);\r
- } else {\r
- (*AdapterInfo->Block) (AdapterInfo->Unique_ID, flag);\r
- }\r
-}\r
-\r
-STATIC\r
-UINT8\r
-Load_Base_Regs (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- //\r
- // we will use the linear (flat) memory model and fill our base registers\r
- // with 0's so that the entire physical address is our offset\r
- //\r
- //\r
- // we reset the statistics totals here because this is where we are loading stats addr\r
- //\r
- AdapterInfo->RxTotals = 0;\r
- AdapterInfo->TxTotals = 0;\r
-\r
- //\r
- // Load the statistics block address.\r
- //\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
- OutLong (AdapterInfo, (UINT32) AdapterInfo->stat_phy_addr, AdapterInfo->ioaddr + SCBPointer);\r
- OutByte (AdapterInfo, CU_STATSADDR, AdapterInfo->ioaddr + SCBCmd);\r
- AdapterInfo->statistics->done_marker = 0;\r
-\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
- OutLong (AdapterInfo, 0, AdapterInfo->ioaddr + SCBPointer);\r
- OutByte (AdapterInfo, RX_ADDR_LOAD, AdapterInfo->ioaddr + SCBCmd);\r
-\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
- OutLong (AdapterInfo, 0, AdapterInfo->ioaddr + SCBPointer);\r
- OutByte (AdapterInfo, CU_CMD_BASE, AdapterInfo->ioaddr + SCBCmd);\r
-\r
- return 0;\r
-}\r
-\r
-STATIC\r
-UINT8\r
-IssueCB (\r
- NIC_DATA_INSTANCE *AdapterInfo,\r
- TxCB *cmd_ptr\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- cmd_ptr - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- UINT16 status;\r
-\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
-\r
- //\r
- // read the CU status, if it is idle, write the address of cb_ptr\r
- // in the scbpointer and issue a cu_start,\r
- // if it is suspended, remove the suspend bit in the previous command\r
- // block and issue a resume\r
- //\r
- // Ensure that the CU Active Status bit is not on from previous CBs.\r
- //\r
- status = InWord (AdapterInfo, AdapterInfo->ioaddr + SCBStatus);\r
-\r
- //\r
- // Skip acknowledging the interrupt if it is not already set\r
- //\r
-\r
- //\r
- // ack only the cna the integer\r
- //\r
- if ((status & SCB_STATUS_CNA) != 0) {\r
- OutWord (AdapterInfo, SCB_STATUS_CNA, AdapterInfo->ioaddr + SCBStatus);\r
-\r
- }\r
-\r
- if ((status & SCB_STATUS_CU_MASK) == SCB_STATUS_CU_IDLE) {\r
- //\r
- // give a cu_start\r
- //\r
- OutLong (AdapterInfo, cmd_ptr->PhysTCBAddress, AdapterInfo->ioaddr + SCBPointer);\r
- OutByte (AdapterInfo, CU_START, AdapterInfo->ioaddr + SCBCmd);\r
- } else {\r
- //\r
- // either active or suspended, give a resume\r
- //\r
-\r
- cmd_ptr->PrevTCBVirtualLinkPtr->cb_header.command &= ~(CmdSuspend | CmdIntr);\r
- OutByte (AdapterInfo, CU_RESUME, AdapterInfo->ioaddr + SCBCmd);\r
- }\r
-\r
- return 0;\r
-}\r
-\r
-STATIC\r
-UINT8\r
-Configure (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- //\r
- // all command blocks are of TxCB format\r
- //\r
- TxCB *cmd_ptr;\r
- UINT8 *data_ptr;\r
- volatile INT16 Index;\r
- UINT8 my_filter;\r
-\r
- cmd_ptr = GetFreeCB (AdapterInfo);\r
- data_ptr = (UINT8 *) (&cmd_ptr->PhysTBDArrayAddres);\r
-\r
- //\r
- // start the config data right after the command header\r
- //\r
- for (Index = 0; Index < sizeof (basic_config_cmd); Index++) {\r
- data_ptr[Index] = basic_config_cmd[Index];\r
- }\r
-\r
- my_filter = (UINT8) ((AdapterInfo->Rx_Filter & PXE_OPFLAGS_RECEIVE_FILTER_PROMISCUOUS) ? 1 : 0);\r
- my_filter = (UINT8) ((my_filter | (AdapterInfo->Rx_Filter & PXE_OPFLAGS_RECEIVE_FILTER_BROADCAST) ? 0 : 2));\r
-\r
- data_ptr[15] = (UINT8) (data_ptr[15] | my_filter);\r
- data_ptr[19] = (UINT8) (AdapterInfo->Duplex ? 0xC0 : 0x80);\r
- data_ptr[21] = (UINT8) ((AdapterInfo->Rx_Filter & PXE_OPFLAGS_RECEIVE_FILTER_ALL_MULTICAST) ? 0x0D : 0x05);\r
-\r
- //\r
- // check if we have to use the AUI port instead\r
- //\r
- if ((AdapterInfo->PhyRecord[0] & 0x8000) != 0) {\r
- data_ptr[15] |= 0x80;\r
- data_ptr[8] = 0;\r
- }\r
-\r
- BlockIt (AdapterInfo, TRUE);\r
- cmd_ptr->cb_header.command = CmdSuspend | CmdConfigure;\r
-\r
- IssueCB (AdapterInfo, cmd_ptr);\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
-\r
- BlockIt (AdapterInfo, FALSE);\r
-\r
- CommandWaitForCompletion (cmd_ptr, AdapterInfo);\r
-\r
- //\r
- // restore the cb values for tx\r
- //\r
- cmd_ptr->PhysTBDArrayAddres = cmd_ptr->PhysArrayAddr;\r
- cmd_ptr->ByteCount = cmd_ptr->Threshold = cmd_ptr->TBDCount = 0;\r
- //\r
- // fields beyond the immediatedata are assumed to be safe\r
- // add the CB to the free list again\r
- //\r
- SetFreeCB (AdapterInfo, cmd_ptr);\r
- return 0;\r
-}\r
-\r
-UINT8\r
-E100bSetupIAAddr (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- //\r
- // all command blocks are of TxCB format\r
- //\r
- TxCB *cmd_ptr;\r
- UINT16 *data_ptr;\r
- UINT16 *eaddrs;\r
-\r
- eaddrs = (UINT16 *) AdapterInfo->CurrentNodeAddress;\r
-\r
- cmd_ptr = GetFreeCB (AdapterInfo);\r
- data_ptr = (UINT16 *) (&cmd_ptr->PhysTBDArrayAddres);\r
-\r
- //\r
- // AVOID a bug (?!) here by marking the command already completed.\r
- //\r
- cmd_ptr->cb_header.command = (CmdSuspend | CmdIASetup);\r
- cmd_ptr->cb_header.status = 0;\r
- data_ptr[0] = eaddrs[0];\r
- data_ptr[1] = eaddrs[1];\r
- data_ptr[2] = eaddrs[2];\r
-\r
- BlockIt (AdapterInfo, TRUE);\r
- IssueCB (AdapterInfo, cmd_ptr);\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
- BlockIt (AdapterInfo, FALSE);\r
-\r
- CommandWaitForCompletion (cmd_ptr, AdapterInfo);\r
-\r
- //\r
- // restore the cb values for tx\r
- //\r
- cmd_ptr->PhysTBDArrayAddres = cmd_ptr->PhysArrayAddr;\r
- cmd_ptr->ByteCount = cmd_ptr->Threshold = cmd_ptr->TBDCount = 0;\r
- //\r
- // fields beyond the immediatedata are assumed to be safe\r
- // add the CB to the free list again\r
- //\r
- SetFreeCB (AdapterInfo, cmd_ptr);\r
- return 0;\r
-}\r
-\r
-STATIC\r
-VOID\r
-StopRU (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- Instructs the NIC to stop receiving packets.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information\r
- which the UNDI driver is layering on..\r
-Returns:\r
-\r
---*/\r
-{\r
- if (AdapterInfo->Receive_Started) {\r
-\r
- //\r
- // Todo: verify that we must wait for previous command completion.\r
- //\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
-\r
- //\r
- // Disable interrupts, and stop the chip's Rx process.\r
- //\r
- OutWord (AdapterInfo, INT_MASK, AdapterInfo->ioaddr + SCBCmd);\r
- OutWord (AdapterInfo, INT_MASK | RX_ABORT, AdapterInfo->ioaddr + SCBCmd);\r
-\r
- AdapterInfo->Receive_Started = FALSE;\r
- }\r
-\r
- return ;\r
-}\r
-\r
-STATIC\r
-INT8\r
-StartRU (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- Instructs the NIC to start receiving packets.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information\r
- which the UNDI driver is layering on..\r
-Returns:\r
- 0 - Successful\r
- -1 - Already Started\r
---*/\r
-{\r
-\r
- if (AdapterInfo->Receive_Started) {\r
- //\r
- // already started\r
- //\r
- return -1;\r
- }\r
-\r
- AdapterInfo->cur_rx_ind = 0;\r
- AdapterInfo->Int_Status = 0;\r
-\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
-\r
- OutLong (AdapterInfo, (UINT32) AdapterInfo->rx_phy_addr, AdapterInfo->ioaddr + SCBPointer);\r
- OutByte (AdapterInfo, RX_START, AdapterInfo->ioaddr + SCBCmd);\r
-\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
-\r
- AdapterInfo->Receive_Started = TRUE;\r
- return 0;\r
-}\r
-\r
-UINTN\r
-E100bInit (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- Configures the chip. This routine expects the NIC_DATA_INSTANCE structure to be filled in.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information\r
- which the UNDI driver is layering on..\r
-\r
-Returns:\r
- 0 - Successful\r
- PXE_STATCODE_NOT_ENOUGH_MEMORY - Insufficient length of locked memory\r
- other - Failure initializing chip\r
---*/\r
-{\r
- PCI_CONFIG_HEADER *CfgHdr;\r
- UINTN stat;\r
- UINTN rx_size;\r
- UINTN tx_size;\r
-\r
- if (AdapterInfo->MemoryLength < MEMORY_NEEDED) {\r
- return PXE_STATCODE_NOT_ENOUGH_MEMORY;\r
- }\r
-\r
- stat = MapIt (\r
- AdapterInfo,\r
- AdapterInfo->MemoryPtr,\r
- AdapterInfo->MemoryLength,\r
- TO_AND_FROM_DEVICE,\r
- (UINT64)(UINTN) &AdapterInfo->Mapped_MemoryPtr\r
- );\r
-\r
- if (stat != 0) {\r
- return stat;\r
- }\r
-\r
- CfgHdr = (PCI_CONFIG_HEADER *) &(AdapterInfo->Config[0]);\r
-\r
- //\r
- // fill in the ioaddr, int... from the config space\r
- //\r
- AdapterInfo->int_num = CfgHdr->int_line;\r
-\r
- //\r
- // we don't need to validate integer number, what if they don't want to assign one?\r
- // if (AdapterInfo->int_num == 0 || AdapterInfo->int_num == 0xff)\r
- // return PXE_STATCODE_DEVICE_FAILURE;\r
- //\r
- AdapterInfo->ioaddr = 0;\r
- AdapterInfo->VendorID = CfgHdr->VendorID;\r
- AdapterInfo->DeviceID = CfgHdr->DeviceID;\r
- AdapterInfo->RevID = CfgHdr->RevID;\r
- AdapterInfo->SubVendorID = CfgHdr->SubVendorID;\r
- AdapterInfo->SubSystemID = CfgHdr->SubSystemID;\r
- AdapterInfo->flash_addr = 0;\r
-\r
- //\r
- // Read the station address EEPROM before doing the reset.\r
- // Perhaps this should even be done before accepting the device,\r
- // then we wouldn't have a device name with which to report the error.\r
- //\r
- if (E100bReadEepromAndStationAddress (AdapterInfo) != 0) {\r
- return PXE_STATCODE_DEVICE_FAILURE;\r
-\r
- }\r
- //\r
- // ## calculate the buffer #s depending on memory given\r
- // ## calculate the rx and tx ring pointers\r
- //\r
-\r
- AdapterInfo->TxBufCnt = TX_BUFFER_COUNT;\r
- AdapterInfo->RxBufCnt = RX_BUFFER_COUNT;\r
- rx_size = (AdapterInfo->RxBufCnt * sizeof (RxFD));\r
- tx_size = (AdapterInfo->TxBufCnt * sizeof (TxCB));\r
- AdapterInfo->rx_ring = (RxFD *) (UINTN) (AdapterInfo->MemoryPtr);\r
- AdapterInfo->tx_ring = (TxCB *) (UINTN) (AdapterInfo->MemoryPtr + rx_size);\r
- AdapterInfo->statistics = (struct speedo_stats *) (UINTN) (AdapterInfo->MemoryPtr + rx_size + tx_size);\r
-\r
- AdapterInfo->rx_phy_addr = AdapterInfo->Mapped_MemoryPtr;\r
- AdapterInfo->tx_phy_addr = AdapterInfo->Mapped_MemoryPtr + rx_size;\r
- AdapterInfo->stat_phy_addr = AdapterInfo->tx_phy_addr + tx_size;\r
- \r
- //\r
- // auto detect.\r
- //\r
- AdapterInfo->PhyAddress = 0xFF;\r
- AdapterInfo->Rx_Filter = PXE_OPFLAGS_RECEIVE_FILTER_BROADCAST;\r
- AdapterInfo->Receive_Started = FALSE;\r
- AdapterInfo->mcast_list.list_len = 0;\r
- return InitializeChip (AdapterInfo);\r
-}\r
-\r
-UINT8\r
-E100bSetInterruptState (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- Sets the interrupt state for the NIC.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information\r
- which the UNDI driver is layering on..\r
-Returns:\r
- 0 - Successful\r
---*/\r
-{\r
- //\r
- // don't set receive interrupt if receiver is disabled...\r
- //\r
- UINT16 cmd_word;\r
-\r
- if ((AdapterInfo->int_mask & PXE_OPFLAGS_INTERRUPT_RECEIVE) != 0) {\r
- cmd_word = InWord (AdapterInfo, AdapterInfo->ioaddr + SCBCmd);\r
- cmd_word &= ~INT_MASK;\r
- OutWord (AdapterInfo, cmd_word, AdapterInfo->ioaddr + SCBCmd);\r
- } else {\r
- //\r
- // disable ints, should not be given for SW Int.\r
- //\r
- OutWord (AdapterInfo, INT_MASK, AdapterInfo->ioaddr + SCBCmd);\r
- }\r
-\r
- if ((AdapterInfo->int_mask & PXE_OPFLAGS_INTERRUPT_SOFTWARE) != 0) {\r
- //\r
- // reset the bit in our mask, it is only one time!!\r
- //\r
- AdapterInfo->int_mask &= ~(PXE_OPFLAGS_INTERRUPT_SOFTWARE);\r
- cmd_word = InWord (AdapterInfo, AdapterInfo->ioaddr + SCBCmd);\r
- cmd_word |= DRVR_INT;\r
- OutWord (AdapterInfo, cmd_word, AdapterInfo->ioaddr + SCBCmd);\r
- }\r
-\r
- return 0;\r
-}\r
-//\r
-// we are not going to disable broadcast for the WOL's sake!\r
-//\r
-UINTN\r
-E100bSetfilter (\r
- NIC_DATA_INSTANCE *AdapterInfo,\r
- UINT16 new_filter,\r
- UINT64 cpb,\r
- UINT32 cpbsize\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- Instructs the NIC to start receiving packets.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information\r
- which the UNDI driver is layering on..\r
- new_filter -\r
- cpb -\r
- cpbsize -\r
-\r
-Returns:\r
- 0 - Successful\r
- -1 - Already Started\r
---*/\r
-{\r
- PXE_CPB_RECEIVE_FILTERS *mc_list = (PXE_CPB_RECEIVE_FILTERS *) (UINTN)cpb;\r
- UINT16 cfg_flt;\r
- UINT16 old_filter;\r
- UINT16 Index;\r
- UINT16 Index2;\r
- UINT16 mc_count;\r
- TxCB *cmd_ptr;\r
- struct MC_CB_STRUCT *data_ptr;\r
- UINT16 mc_byte_cnt;\r
-\r
- old_filter = AdapterInfo->Rx_Filter;\r
-\r
- //\r
- // only these bits need a change in the configuration\r
- // actually change in bcast requires configure but we ignore that change\r
- //\r
- cfg_flt = PXE_OPFLAGS_RECEIVE_FILTER_PROMISCUOUS |\r
- PXE_OPFLAGS_RECEIVE_FILTER_ALL_MULTICAST;\r
-\r
- if ((old_filter & cfg_flt) != (new_filter & cfg_flt)) {\r
- XmitWaitForCompletion (AdapterInfo);\r
-\r
- if (AdapterInfo->Receive_Started) {\r
- StopRU (AdapterInfo);\r
- }\r
-\r
- AdapterInfo->Rx_Filter = (UINT8) (new_filter | PXE_OPFLAGS_RECEIVE_FILTER_BROADCAST);\r
- Configure (AdapterInfo);\r
- }\r
-\r
- //\r
- // check if mcast setting changed\r
- //\r
- if ( ((new_filter & PXE_OPFLAGS_RECEIVE_FILTER_FILTERED_MULTICAST) !=\r
- (old_filter & PXE_OPFLAGS_RECEIVE_FILTER_FILTERED_MULTICAST) ) ||\r
- (mc_list != NULL) ) {\r
-\r
-\r
- if (mc_list != NULL) {\r
- mc_count = AdapterInfo->mcast_list.list_len = (UINT16) (cpbsize / PXE_MAC_LENGTH);\r
-\r
- for (Index = 0; (Index < mc_count && Index < MAX_MCAST_ADDRESS_CNT); Index++) {\r
- for (Index2 = 0; Index2 < PXE_MAC_LENGTH; Index2++) {\r
- AdapterInfo->mcast_list.mc_list[Index][Index2] = mc_list->MCastList[Index][Index2];\r
- }\r
- }\r
- }\r
-\r
- //\r
- // are we setting the list or resetting??\r
- //\r
- if ((new_filter & PXE_OPFLAGS_RECEIVE_FILTER_FILTERED_MULTICAST) != 0) {\r
- //\r
- // we are setting a new list!\r
- //\r
- mc_count = AdapterInfo->mcast_list.list_len;\r
- //\r
- // count should be the actual # of bytes in the list\r
- // so multiply this with 6\r
- //\r
- mc_byte_cnt = (UINT16) ((mc_count << 2) + (mc_count << 1));\r
- AdapterInfo->Rx_Filter |= PXE_OPFLAGS_RECEIVE_FILTER_FILTERED_MULTICAST;\r
- } else {\r
- //\r
- // disabling the list in the NIC.\r
- //\r
- mc_byte_cnt = mc_count = 0;\r
- AdapterInfo->Rx_Filter &= (~PXE_OPFLAGS_RECEIVE_FILTER_FILTERED_MULTICAST);\r
- }\r
-\r
- //\r
- // before issuing any new command!\r
- //\r
- XmitWaitForCompletion (AdapterInfo);\r
-\r
- if (AdapterInfo->Receive_Started) {\r
- StopRU (AdapterInfo);\r
-\r
- }\r
-\r
- cmd_ptr = GetFreeCB (AdapterInfo);\r
- if (cmd_ptr == NULL) {\r
- return PXE_STATCODE_QUEUE_FULL;\r
- }\r
- //\r
- // fill the command structure and issue\r
- //\r
- data_ptr = (struct MC_CB_STRUCT *) (&cmd_ptr->PhysTBDArrayAddres);\r
- //\r
- // first 2 bytes are the count;\r
- //\r
- data_ptr->count = mc_byte_cnt;\r
- for (Index = 0; Index < mc_count; Index++) {\r
- for (Index2 = 0; Index2 < PXE_HWADDR_LEN_ETHER; Index2++) {\r
- data_ptr->m_list[Index][Index2] = AdapterInfo->mcast_list.mc_list[Index][Index2];\r
- }\r
- }\r
-\r
- cmd_ptr->cb_header.command = CmdSuspend | CmdMulticastList;\r
- cmd_ptr->cb_header.status = 0;\r
-\r
- BlockIt (AdapterInfo, TRUE);\r
- IssueCB (AdapterInfo, cmd_ptr);\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
-\r
- BlockIt (AdapterInfo, FALSE);\r
-\r
- CommandWaitForCompletion (cmd_ptr, AdapterInfo);\r
-\r
- cmd_ptr->PhysTBDArrayAddres = cmd_ptr->PhysArrayAddr;\r
- cmd_ptr->ByteCount = cmd_ptr->Threshold = cmd_ptr->TBDCount = 0;\r
- //\r
- // fields beyond the immediatedata are assumed to be safe\r
- // add the CB to the free list again\r
- //\r
- SetFreeCB (AdapterInfo, cmd_ptr);\r
- }\r
-\r
- if (new_filter != 0) {\r
- //\r
- // enable unicast and start the RU\r
- //\r
- AdapterInfo->Rx_Filter = (UINT8) (AdapterInfo->Rx_Filter | (new_filter | PXE_OPFLAGS_RECEIVE_FILTER_UNICAST));\r
- StartRU (AdapterInfo);\r
- } else {\r
- //\r
- // may be disabling everything!\r
- //\r
- if (AdapterInfo->Receive_Started) {\r
- StopRU (AdapterInfo);\r
- }\r
-\r
- AdapterInfo->Rx_Filter |= (~PXE_OPFLAGS_RECEIVE_FILTER_UNICAST);\r
- }\r
-\r
- return 0;\r
-}\r
-\r
-UINTN\r
-E100bTransmit (\r
- NIC_DATA_INSTANCE *AdapterInfo,\r
- UINT64 cpb,\r
- UINT16 opflags\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- cpb - TODO: add argument description\r
- opflags - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- PXE_CPB_TRANSMIT_FRAGMENTS *tx_ptr_f;\r
- PXE_CPB_TRANSMIT *tx_ptr_1;\r
- TxCB *tcb_ptr;\r
- UINT64 Tmp_ptr;\r
- UINTN stat;\r
- INT32 Index;\r
- UINT16 wait_sec;\r
-\r
- tx_ptr_1 = (PXE_CPB_TRANSMIT *) (UINTN) cpb;\r
- tx_ptr_f = (PXE_CPB_TRANSMIT_FRAGMENTS *) (UINTN) cpb;\r
-\r
- //\r
- // stop reentrancy here\r
- //\r
- if (AdapterInfo->in_transmit) {\r
- return PXE_STATCODE_BUSY;\r
-\r
- }\r
-\r
- AdapterInfo->in_transmit = TRUE;\r
-\r
- //\r
- // Prevent interrupts from changing the Tx ring from underneath us.\r
- //\r
- // Calculate the Tx descriptor entry.\r
- //\r
- if ((tcb_ptr = GetFreeCB (AdapterInfo)) == NULL) {\r
- AdapterInfo->in_transmit = FALSE;\r
- return PXE_STATCODE_QUEUE_FULL;\r
- }\r
-\r
- AdapterInfo->TxTotals++;\r
-\r
- tcb_ptr->cb_header.command = (CmdSuspend | CmdTx | CmdTxFlex);\r
- tcb_ptr->cb_header.status = 0;\r
-\r
- //\r
- // no immediate data, set EOF in the ByteCount\r
- //\r
- tcb_ptr->ByteCount = 0x8000;\r
-\r
- //\r
- // The data region is always in one buffer descriptor, Tx FIFO\r
- // threshold of 256.\r
- // 82557 multiplies the threashold value by 8, so give 256/8\r
- //\r
- tcb_ptr->Threshold = 32;\r
- if ((opflags & PXE_OPFLAGS_TRANSMIT_FRAGMENTED) != 0) {\r
-\r
- if (tx_ptr_f->FragCnt > MAX_XMIT_FRAGMENTS) {\r
- SetFreeCB (AdapterInfo, tcb_ptr);\r
- AdapterInfo->in_transmit = FALSE;\r
- return PXE_STATCODE_INVALID_PARAMETER;\r
- }\r
-\r
- tcb_ptr->TBDCount = (UINT8) tx_ptr_f->FragCnt;\r
-\r
- for (Index = 0; Index < tx_ptr_f->FragCnt; Index++) {\r
- stat = MapIt (\r
- AdapterInfo,\r
- tx_ptr_f->FragDesc[Index].FragAddr,\r
- tx_ptr_f->FragDesc[Index].FragLen,\r
- TO_DEVICE,\r
- (UINT64)(UINTN) &Tmp_ptr\r
- );\r
- if (stat != 0) {\r
- SetFreeCB (AdapterInfo, tcb_ptr);\r
- AdapterInfo->in_transmit = FALSE;\r
- return PXE_STATCODE_INVALID_PARAMETER;\r
- }\r
-\r
- tcb_ptr->TBDArray[Index].phys_buf_addr = (UINT32) Tmp_ptr;\r
- tcb_ptr->TBDArray[Index].buf_len = tx_ptr_f->FragDesc[Index].FragLen;\r
- }\r
-\r
- tcb_ptr->free_data_ptr = tx_ptr_f->FragDesc[0].FragAddr;\r
-\r
- } else {\r
- //\r
- // non fragmented case\r
- //\r
- tcb_ptr->TBDCount = 1;\r
- stat = MapIt (\r
- AdapterInfo,\r
- tx_ptr_1->FrameAddr,\r
- tx_ptr_1->DataLen + tx_ptr_1->MediaheaderLen,\r
- TO_DEVICE,\r
- (UINT64)(UINTN) &Tmp_ptr\r
- );\r
- if (stat != 0) {\r
- SetFreeCB (AdapterInfo, tcb_ptr);\r
- AdapterInfo->in_transmit = FALSE;\r
- return PXE_STATCODE_INVALID_PARAMETER;\r
- }\r
-\r
- tcb_ptr->TBDArray[0].phys_buf_addr = (UINT32) (Tmp_ptr);\r
- tcb_ptr->TBDArray[0].buf_len = tx_ptr_1->DataLen + tx_ptr_1->MediaheaderLen;\r
- tcb_ptr->free_data_ptr = tx_ptr_1->FrameAddr;\r
- }\r
-\r
- //\r
- // must wait for previous command completion only if it was a non-transmit\r
- //\r
- BlockIt (AdapterInfo, TRUE);\r
- IssueCB (AdapterInfo, tcb_ptr);\r
- BlockIt (AdapterInfo, FALSE);\r
-\r
- //\r
- // see if we need to wait for completion here\r
- //\r
- if ((opflags & PXE_OPFLAGS_TRANSMIT_BLOCK) != 0) {\r
- //\r
- // don't wait for more than 1 second!!!\r
- //\r
- wait_sec = 1000;\r
- while (tcb_ptr->cb_header.status == 0) {\r
- DelayIt (AdapterInfo, 10);\r
- wait_sec--;\r
- if (wait_sec == 0) {\r
- break;\r
- }\r
- }\r
- //\r
- // we need to un-map any mapped buffers here\r
- //\r
- if ((opflags & PXE_OPFLAGS_TRANSMIT_FRAGMENTED) != 0) {\r
-\r
- for (Index = 0; Index < tx_ptr_f->FragCnt; Index++) {\r
- Tmp_ptr = tcb_ptr->TBDArray[Index].phys_buf_addr;\r
- UnMapIt (\r
- AdapterInfo,\r
- tx_ptr_f->FragDesc[Index].FragAddr,\r
- tx_ptr_f->FragDesc[Index].FragLen,\r
- TO_DEVICE,\r
- (UINT64) Tmp_ptr\r
- );\r
- }\r
- } else {\r
- Tmp_ptr = tcb_ptr->TBDArray[0].phys_buf_addr;\r
- UnMapIt (\r
- AdapterInfo,\r
- tx_ptr_1->FrameAddr,\r
- tx_ptr_1->DataLen + tx_ptr_1->MediaheaderLen,\r
- TO_DEVICE,\r
- (UINT64) Tmp_ptr\r
- );\r
- }\r
-\r
- if (tcb_ptr->cb_header.status == 0) {\r
- SetFreeCB (AdapterInfo, tcb_ptr);\r
- AdapterInfo->in_transmit = FALSE;\r
- return PXE_STATCODE_DEVICE_FAILURE;\r
- }\r
-\r
- SetFreeCB (AdapterInfo, tcb_ptr);\r
- }\r
- //\r
- // CB will be set free later in get_status (or when we run out of xmit buffers\r
- //\r
- AdapterInfo->in_transmit = FALSE;\r
-\r
- return 0;\r
-}\r
-\r
-UINTN\r
-E100bReceive (\r
- NIC_DATA_INSTANCE *AdapterInfo,\r
- UINT64 cpb,\r
- UINT64 db\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- cpb - TODO: add argument description\r
- db - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- PXE_CPB_RECEIVE *rx_cpbptr;\r
- PXE_DB_RECEIVE *rx_dbptr;\r
- RxFD *rx_ptr;\r
- INT32 status;\r
- INT32 Index;\r
- UINT16 pkt_len;\r
- UINT16 ret_code;\r
- PXE_FRAME_TYPE pkt_type;\r
- UINT16 Tmp_len;\r
- EtherHeader *hdr_ptr;\r
- ret_code = PXE_STATCODE_NO_DATA;\r
- pkt_type = PXE_FRAME_TYPE_NONE;\r
- status = InWord (AdapterInfo, AdapterInfo->ioaddr + SCBStatus);\r
- AdapterInfo->Int_Status = (UINT16) (AdapterInfo->Int_Status | status);\r
- //\r
- // acknoledge the interrupts\r
- //\r
- OutWord (AdapterInfo, (UINT16) (status & 0xfc00), (UINT32) (AdapterInfo->ioaddr + SCBStatus));\r
-\r
- //\r
- // include the prev ints as well\r
- //\r
- status = AdapterInfo->Int_Status;\r
- rx_cpbptr = (PXE_CPB_RECEIVE *) (UINTN) cpb;\r
- rx_dbptr = (PXE_DB_RECEIVE *) (UINTN) db;\r
-\r
- rx_ptr = &AdapterInfo->rx_ring[AdapterInfo->cur_rx_ind];\r
-\r
- //\r
- // be in a loop just in case (we may drop a pkt)\r
- //\r
- while ((status = rx_ptr->cb_header.status) & RX_COMPLETE) {\r
-\r
- AdapterInfo->RxTotals++;\r
- //\r
- // If we own the next entry, it's a new packet. Send it up.\r
- //\r
- if (rx_ptr->forwarded) {\r
- goto FreeRFD;\r
-\r
- }\r
-\r
- //\r
- // discard bad frames\r
- //\r
-\r
- //\r
- // crc, align, dma overrun, too short, receive error (v22 no coll)\r
- //\r
- if ((status & 0x0D90) != 0) {\r
- goto FreeRFD;\r
-\r
- }\r
-\r
- //\r
- // make sure the status is OK\r
- //\r
- if ((status & 0x02000) == 0) {\r
- goto FreeRFD;\r
- }\r
-\r
- pkt_len = (UINT16) (rx_ptr->ActualCount & 0x3fff);\r
-\r
- if (pkt_len != 0) {\r
-\r
- Tmp_len = pkt_len;\r
- if (pkt_len > rx_cpbptr->BufferLen) {\r
- Tmp_len = (UINT16) rx_cpbptr->BufferLen;\r
- }\r
-\r
- CopyMem ((INT8 *) (UINTN) rx_cpbptr->BufferAddr, (INT8 *) &rx_ptr->RFDBuffer, Tmp_len);\r
-\r
- hdr_ptr = (EtherHeader *) &rx_ptr->RFDBuffer;\r
- //\r
- // fill the CDB and break the loop\r
- //\r
-\r
- //\r
- // includes header\r
- //\r
- rx_dbptr->FrameLen = pkt_len;\r
- rx_dbptr->MediaHeaderLen = PXE_MAC_HEADER_LEN_ETHER;\r
-\r
- for (Index = 0; Index < PXE_HWADDR_LEN_ETHER; Index++) {\r
- if (hdr_ptr->dest_addr[Index] != AdapterInfo->CurrentNodeAddress[Index]) {\r
- break;\r
- }\r
- }\r
-\r
- if (Index >= PXE_HWADDR_LEN_ETHER) {\r
- pkt_type = PXE_FRAME_TYPE_UNICAST;\r
- } else {\r
- for (Index = 0; Index < PXE_HWADDR_LEN_ETHER; Index++) {\r
- if (hdr_ptr->dest_addr[Index] != AdapterInfo->BroadcastNodeAddress[Index]) {\r
- break;\r
- }\r
- }\r
-\r
- if (Index >= PXE_HWADDR_LEN_ETHER) {\r
- pkt_type = PXE_FRAME_TYPE_BROADCAST;\r
- } else {\r
- if ((hdr_ptr->dest_addr[0] & 1) == 1) {\r
- //\r
- // mcast\r
- //\r
-\r
- pkt_type = PXE_FRAME_TYPE_MULTICAST;\r
- } else {\r
- pkt_type = PXE_FRAME_TYPE_PROMISCUOUS;\r
- }\r
- }\r
- }\r
-\r
- rx_dbptr->Type = pkt_type;\r
- rx_dbptr->Protocol = hdr_ptr->type;\r
-\r
- for (Index = 0; Index < PXE_HWADDR_LEN_ETHER; Index++) {\r
- rx_dbptr->SrcAddr[Index] = hdr_ptr->src_addr[Index];\r
- rx_dbptr->DestAddr[Index] = hdr_ptr->dest_addr[Index];\r
- }\r
-\r
- rx_ptr->forwarded = TRUE;\r
- //\r
- // success\r
- //\r
- ret_code = 0;\r
- Recycle_RFD (AdapterInfo, AdapterInfo->cur_rx_ind);\r
- AdapterInfo->cur_rx_ind++;\r
- if (AdapterInfo->cur_rx_ind == AdapterInfo->RxBufCnt) {\r
- AdapterInfo->cur_rx_ind = 0;\r
- }\r
- break;\r
- }\r
-\r
-FreeRFD:\r
- Recycle_RFD (AdapterInfo, AdapterInfo->cur_rx_ind);\r
- AdapterInfo->cur_rx_ind++;\r
- if (AdapterInfo->cur_rx_ind == AdapterInfo->RxBufCnt) {\r
- AdapterInfo->cur_rx_ind = 0;\r
- }\r
-\r
- rx_ptr = &AdapterInfo->rx_ring[AdapterInfo->cur_rx_ind];\r
- }\r
-\r
- if (pkt_type == PXE_FRAME_TYPE_NONE) {\r
- AdapterInfo->Int_Status &= (~SCB_STATUS_FR);\r
- }\r
-\r
- status = InWord (AdapterInfo, AdapterInfo->ioaddr + SCBStatus);\r
- if ((status & SCB_RUS_NO_RESOURCES) != 0) {\r
- //\r
- // start the receive unit here!\r
- // leave all the filled frames,\r
- //\r
- SetupReceiveQueues (AdapterInfo);\r
- OutLong (AdapterInfo, (UINT32) AdapterInfo->rx_phy_addr, AdapterInfo->ioaddr + SCBPointer);\r
- OutWord (AdapterInfo, RX_START, AdapterInfo->ioaddr + SCBCmd);\r
- AdapterInfo->cur_rx_ind = 0;\r
- }\r
-\r
- return ret_code;\r
-}\r
-\r
-INT16\r
-E100bReadEepromAndStationAddress (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- INT32 Index;\r
- INT32 Index2;\r
- UINT16 sum;\r
- UINT16 eeprom_len;\r
- UINT8 addr_len;\r
- UINT16 *eedata;\r
-\r
- eedata = (UINT16 *) (&AdapterInfo->NVData[0]);\r
-\r
- sum = 0;\r
- addr_len = E100bGetEepromAddrLen (AdapterInfo);\r
-\r
- //\r
- // in words\r
- //\r
- AdapterInfo->NVData_Len = eeprom_len = (UINT16) (1 << addr_len);\r
- for (Index2 = 0, Index = 0; Index < eeprom_len; Index++) {\r
- UINT16 value;\r
- value = E100bReadEeprom (AdapterInfo, Index, addr_len);\r
- eedata[Index] = value;\r
- sum = (UINT16) (sum + value);\r
- if (Index < 3) {\r
- AdapterInfo->PermNodeAddress[Index2++] = (UINT8) value;\r
- AdapterInfo->PermNodeAddress[Index2++] = (UINT8) (value >> 8);\r
- }\r
- }\r
-\r
- if (sum != 0xBABA) {\r
- return -1;\r
- }\r
-\r
- for (Index = 0; Index < PXE_HWADDR_LEN_ETHER; Index++) {\r
- AdapterInfo->CurrentNodeAddress[Index] = AdapterInfo->PermNodeAddress[Index];\r
- }\r
-\r
- for (Index = 0; Index < PXE_HWADDR_LEN_ETHER; Index++) {\r
- AdapterInfo->BroadcastNodeAddress[Index] = 0xff;\r
- }\r
-\r
- for (Index = PXE_HWADDR_LEN_ETHER; Index < PXE_MAC_LENGTH; Index++) {\r
- AdapterInfo->CurrentNodeAddress[Index] = 0;\r
- AdapterInfo->PermNodeAddress[Index] = 0;\r
- AdapterInfo->BroadcastNodeAddress[Index] = 0;\r
- }\r
-\r
- return 0;\r
-}\r
-\r
-//\r
-// CBList is a circular linked list\r
-// 1) When all are free, Tail->next == Head and FreeCount == # allocated\r
-// 2) When none are free, Tail == Head and FreeCount == 0\r
-// 3) when one is free, Tail == Head and Freecount == 1\r
-// 4) First non-Free frame is always at Tail->next\r
-//\r
-UINT8\r
-SetupCBlink (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- TxCB *head_ptr;\r
- TxCB *tail_ptr;\r
- TxCB *cur_ptr;\r
- INT32 Index;\r
- UINTN array_off;\r
-\r
- cur_ptr = &(AdapterInfo->tx_ring[0]);\r
- array_off = (UINTN) (&cur_ptr->TBDArray) - (UINTN) cur_ptr;\r
- for (Index = 0; Index < AdapterInfo->TxBufCnt; Index++) {\r
- cur_ptr[Index].cb_header.status = 0;\r
- cur_ptr[Index].cb_header.command = 0;\r
-\r
- cur_ptr[Index].PhysTCBAddress =\r
- (UINT32) AdapterInfo->tx_phy_addr + (Index * sizeof (TxCB));\r
-\r
- cur_ptr[Index].PhysArrayAddr = (UINT32)(cur_ptr[Index].PhysTCBAddress + array_off); \r
- cur_ptr[Index].PhysTBDArrayAddres = (UINT32)(cur_ptr[Index].PhysTCBAddress + array_off);\r
-\r
- cur_ptr->free_data_ptr = (UINT64) 0;\r
-\r
- if (Index < AdapterInfo->TxBufCnt - 1) {\r
- cur_ptr[Index].cb_header.link = cur_ptr[Index].PhysTCBAddress + sizeof (TxCB);\r
- cur_ptr[Index].NextTCBVirtualLinkPtr = &cur_ptr[Index + 1];\r
- cur_ptr[Index + 1].PrevTCBVirtualLinkPtr = &cur_ptr[Index];\r
- }\r
- }\r
-\r
- head_ptr = &cur_ptr[0];\r
- tail_ptr = &cur_ptr[AdapterInfo->TxBufCnt - 1];\r
- tail_ptr->cb_header.link = head_ptr->PhysTCBAddress;\r
- tail_ptr->NextTCBVirtualLinkPtr = head_ptr;\r
- head_ptr->PrevTCBVirtualLinkPtr = tail_ptr;\r
-\r
- AdapterInfo->FreeCBCount = AdapterInfo->TxBufCnt;\r
- AdapterInfo->FreeTxHeadPtr = head_ptr;\r
- //\r
- // set tail of the free list, next to this would be either in use\r
- // or the head itself\r
- //\r
- AdapterInfo->FreeTxTailPtr = tail_ptr;\r
-\r
- AdapterInfo->xmit_done_head = AdapterInfo->xmit_done_tail = 0;\r
-\r
- return 0;\r
-}\r
-\r
-TxCB *\r
-GetFreeCB (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- TxCB *free_cb_ptr;\r
-\r
- //\r
- // claim any hanging free CBs\r
- //\r
- if (AdapterInfo->FreeCBCount <= 1) {\r
- CheckCBList (AdapterInfo);\r
- }\r
-\r
- //\r
- // don't use up the last CB problem if the previous CB that the CU used\r
- // becomes the last CB we submit because of the SUSPEND bit we set.\r
- // the CU thinks it was never cleared.\r
- //\r
-\r
- if (AdapterInfo->FreeCBCount <= 1) {\r
- return NULL;\r
- }\r
-\r
- BlockIt (AdapterInfo, TRUE);\r
- free_cb_ptr = AdapterInfo->FreeTxHeadPtr;\r
- AdapterInfo->FreeTxHeadPtr = free_cb_ptr->NextTCBVirtualLinkPtr;\r
- --AdapterInfo->FreeCBCount;\r
- BlockIt (AdapterInfo, FALSE);\r
- return free_cb_ptr;\r
-}\r
-\r
-VOID\r
-SetFreeCB (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN TxCB *cb_ptr\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- cb_ptr - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- //\r
- // here we assume cb are returned in the order they are taken out\r
- // and we link the newly freed cb at the tail of free cb list\r
- //\r
- cb_ptr->cb_header.status = 0;\r
- cb_ptr->free_data_ptr = (UINT64) 0;\r
-\r
- AdapterInfo->FreeTxTailPtr = cb_ptr;\r
- ++AdapterInfo->FreeCBCount;\r
- return ;\r
-}\r
-\r
-UINT16\r
-next (\r
- IN UINT16 ind\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- ind - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- UINT16 Tmp;\r
-\r
- Tmp = (UINT16) (ind + 1);\r
- if (Tmp >= (TX_BUFFER_COUNT << 1)) {\r
- Tmp = 0;\r
- }\r
-\r
- return Tmp;\r
-}\r
-\r
-UINT16\r
-CheckCBList (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- TxCB *Tmp_ptr;\r
- UINT16 cnt;\r
-\r
- cnt = 0;\r
- while (1) {\r
- Tmp_ptr = AdapterInfo->FreeTxTailPtr->NextTCBVirtualLinkPtr;\r
- if ((Tmp_ptr->cb_header.status & CMD_STATUS_MASK) != 0) {\r
- //\r
- // check if Q is full\r
- //\r
- if (next (AdapterInfo->xmit_done_tail) != AdapterInfo->xmit_done_head) {\r
- AdapterInfo->xmit_done[AdapterInfo->xmit_done_tail] = Tmp_ptr->free_data_ptr;\r
-\r
- UnMapIt (\r
- AdapterInfo,\r
- Tmp_ptr->free_data_ptr,\r
- Tmp_ptr->TBDArray[0].buf_len,\r
- TO_DEVICE,\r
- (UINT64) Tmp_ptr->TBDArray[0].phys_buf_addr\r
- );\r
-\r
- AdapterInfo->xmit_done_tail = next (AdapterInfo->xmit_done_tail);\r
- }\r
-\r
- SetFreeCB (AdapterInfo, Tmp_ptr);\r
- } else {\r
- break;\r
- }\r
- }\r
-\r
- return cnt;\r
-}\r
-//\r
-// Description : Initialize the RFD list list by linking each element together\r
-// in a circular list. The simplified memory model is used.\r
-// All data is in the RFD. The RFDs are linked together and the\r
-// last one points back to the first one. When the current RFD\r
-// is processed (frame received), its EL bit is set and the EL\r
-// bit in the previous RXFD is cleared.\r
-// Allocation done during INIT, this is making linked list.\r
-//\r
-UINT8\r
-SetupReceiveQueues (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- RxFD *rx_ptr;\r
- RxFD *tail_ptr;\r
- UINT16 Index;\r
-\r
- AdapterInfo->cur_rx_ind = 0;\r
- rx_ptr = (&AdapterInfo->rx_ring[0]);\r
-\r
- for (Index = 0; Index < AdapterInfo->RxBufCnt; Index++) {\r
- rx_ptr[Index].cb_header.status = 0;\r
- rx_ptr[Index].cb_header.command = 0;\r
- rx_ptr[Index].RFDSize = RX_BUFFER_SIZE;\r
- rx_ptr[Index].ActualCount = 0;\r
- //\r
- // RBDs not used, simple memory model\r
- //\r
- rx_ptr[Index].rx_buf_addr = (UINT32) (-1);\r
-\r
- //\r
- // RBDs not used, simple memory model\r
- //\r
- rx_ptr[Index].forwarded = FALSE;\r
-\r
- //\r
- // don't use Tmp_ptr if it is beyond the last one\r
- //\r
- if (Index < AdapterInfo->RxBufCnt - 1) {\r
- rx_ptr[Index].cb_header.link = (UINT32) AdapterInfo->rx_phy_addr + ((Index + 1) * sizeof (RxFD));\r
- }\r
- }\r
-\r
- tail_ptr = (&AdapterInfo->rx_ring[AdapterInfo->RxBufCnt - 1]);\r
- tail_ptr->cb_header.link = (UINT32) AdapterInfo->rx_phy_addr;\r
-\r
- //\r
- // set the EL bit\r
- //\r
- tail_ptr->cb_header.command = 0xC000;\r
- AdapterInfo->RFDTailPtr = tail_ptr;\r
- return 0;\r
-}\r
-\r
-VOID\r
-Recycle_RFD (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT16 rx_index\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- rx_index - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- RxFD *rx_ptr;\r
- RxFD *tail_ptr;\r
- //\r
- // change the EL bit and change the AdapterInfo->RxTailPtr\r
- // rx_ptr is assumed to be the head of the Q\r
- // AdapterInfo->rx_forwarded[rx_index] = FALSE;\r
- //\r
- rx_ptr = &AdapterInfo->rx_ring[rx_index];\r
- tail_ptr = AdapterInfo->RFDTailPtr;\r
- //\r
- // set el_bit and suspend bit\r
- //\r
- rx_ptr->cb_header.command = 0xc000;\r
- rx_ptr->cb_header.status = 0;\r
- rx_ptr->ActualCount = 0;\r
- rx_ptr->forwarded = FALSE;\r
- AdapterInfo->RFDTailPtr = rx_ptr;\r
- //\r
- // resetting the el_bit.\r
- //\r
- tail_ptr->cb_header.command = 0;\r
- //\r
- // check the receive unit, fix if there is any problem\r
- //\r
- return ;\r
-}\r
-//\r
-// Serial EEPROM section.\r
-//\r
-// EEPROM_Ctrl bits.\r
-//\r
-#define EE_SHIFT_CLK 0x01 /* EEPROM shift clock. */\r
-#define EE_CS 0x02 /* EEPROM chip select. */\r
-#define EE_DI 0x04 /* EEPROM chip data in. */\r
-#define EE_WRITE_0 0x01\r
-#define EE_WRITE_1 0x05\r
-#define EE_DO 0x08 /* EEPROM chip data out. */\r
-#define EE_ENB (0x4800 | EE_CS)\r
-\r
-//\r
-// Delay between EEPROM clock transitions.\r
-// This will actually work with no delay on 33Mhz PCI.\r
-//\r
-#define eeprom_delay(nanosec) DelayIt (AdapterInfo, nanosec);\r
-\r
-//\r
-// The EEPROM commands include the alway-set leading bit.\r
-//\r
-#define EE_WRITE_CMD 5 // 101b\r
-#define EE_READ_CMD 6 // 110b\r
-#define EE_ERASE_CMD (7 << 6)\r
-\r
-STATIC\r
-VOID\r
-shift_bits_out (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT16 val,\r
- IN UINT8 num_bits\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- val - TODO: add argument description\r
- num_bits - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- INT32 Index;\r
- UINT8 Tmp;\r
- UINT32 EEAddr;\r
-\r
- EEAddr = AdapterInfo->ioaddr + SCBeeprom;\r
-\r
- for (Index = num_bits; Index >= 0; Index--) {\r
- INT16 dataval;\r
-\r
- //\r
- // will be 0 or 4\r
- //\r
- dataval = (INT16) ((val & (1 << Index)) ? EE_DI : 0);\r
-\r
- //\r
- // mask off the data_in bit\r
- //\r
- Tmp = (UINT8) (InByte (AdapterInfo, EEAddr) &~EE_DI);\r
- Tmp = (UINT8) (Tmp | dataval);\r
- OutByte (AdapterInfo, Tmp, EEAddr);\r
- eeprom_delay (100);\r
- //\r
- // raise the eeprom clock\r
- //\r
- OutByte (AdapterInfo, (UINT8) (Tmp | EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (150);\r
- //\r
- // lower the eeprom clock\r
- //\r
- OutByte (AdapterInfo, (UINT8) (Tmp &~EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (150);\r
- }\r
-}\r
-\r
-STATIC\r
-UINT16\r
-shift_bits_in (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- UINT8 Tmp;\r
- INT32 Index;\r
- UINT16 retval;\r
- UINT32 EEAddr;\r
-\r
- EEAddr = AdapterInfo->ioaddr + SCBeeprom;\r
-\r
- retval = 0;\r
- for (Index = 15; Index >= 0; Index--) {\r
- //\r
- // raise the clock\r
- //\r
-\r
- //\r
- // mask off the data_in bit\r
- //\r
- Tmp = InByte (AdapterInfo, EEAddr);\r
- OutByte (AdapterInfo, (UINT8) (Tmp | EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (100);\r
- Tmp = InByte (AdapterInfo, EEAddr);\r
- retval = (UINT16) ((retval << 1) | ((Tmp & EE_DO) ? 1 : 0));\r
- //\r
- // lower the clock\r
- //\r
- OutByte (AdapterInfo, (UINT8) (Tmp &~EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (100);\r
- }\r
-\r
- return retval;\r
-}\r
-\r
-STATIC\r
-BOOLEAN\r
-E100bSetEepromLockOut (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This routine sets the EEPROM lockout bit to gain exclusive access to the\r
- eeprom. the access bit is the most significant bit in the General Control\r
- Register 2 in the SCB space.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information which the UNDI driver is layering on..\r
-\r
-Returns:\r
- TRUE - if it got the access\r
- FALSE - if it fails to get the exclusive access\r
-\r
---*/\r
-{\r
- UINTN wait;\r
- UINT8 tmp;\r
-\r
- if ((AdapterInfo->DeviceID == D102_DEVICE_ID) || \r
- (AdapterInfo->RevID >= D102_REVID)) {\r
-\r
- wait = 500;\r
-\r
- while (wait--) {\r
-\r
- tmp = InByte (AdapterInfo, AdapterInfo->ioaddr + SCBGenCtrl2);\r
- tmp |= GCR2_EEPROM_ACCESS_SEMAPHORE;\r
- OutByte (AdapterInfo, tmp, AdapterInfo->ioaddr + SCBGenCtrl2);\r
-\r
- DelayIt (AdapterInfo, 50);\r
- tmp = InByte (AdapterInfo, AdapterInfo->ioaddr + SCBGenCtrl2);\r
-\r
- if (tmp & GCR2_EEPROM_ACCESS_SEMAPHORE) {\r
- return TRUE;\r
- }\r
- }\r
-\r
- return FALSE;\r
- }\r
-\r
- return TRUE;\r
-}\r
-\r
-STATIC\r
-VOID\r
-E100bReSetEepromLockOut (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This routine Resets the EEPROM lockout bit to giveup access to the\r
- eeprom. the access bit is the most significant bit in the General Control\r
- Register 2 in the SCB space.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information which the UNDI driver is layering on..\r
-\r
-Returns:\r
- None\r
- \r
---*/\r
-{\r
- UINT8 tmp;\r
-\r
- if ((AdapterInfo->DeviceID == D102_DEVICE_ID) || \r
- (AdapterInfo->RevID >= D102_REVID)) {\r
-\r
- tmp = InByte (AdapterInfo, AdapterInfo->ioaddr + SCBGenCtrl2);\r
- tmp &= ~(GCR2_EEPROM_ACCESS_SEMAPHORE);\r
- OutByte (AdapterInfo, tmp, AdapterInfo->ioaddr + SCBGenCtrl2);\r
-\r
- DelayIt (AdapterInfo, 50);\r
- }\r
-}\r
-\r
-UINT16\r
-E100bReadEeprom (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN INT32 Location,\r
- IN UINT8 AddrLen\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- Using the NIC data structure information, read the EEPROM to get a Word of data for the MAC address.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information which the UNDI driver is layering on..\r
- Location - Word offset into the MAC address to read.\r
- AddrLen - Number of bits of address length.\r
-\r
-Returns:\r
- RetVal - The word read from the EEPROM.\r
-\r
---*/\r
-{\r
- UINT16 RetVal;\r
- UINT8 Tmp;\r
-\r
- UINT32 EEAddr;\r
- UINT16 ReadCmd;\r
-\r
- EEAddr = AdapterInfo->ioaddr + SCBeeprom;\r
- ReadCmd = (UINT16) (Location | (EE_READ_CMD << AddrLen));\r
-\r
- RetVal = 0;\r
-\r
- //\r
- // get exclusive access to the eeprom first!\r
- //\r
- E100bSetEepromLockOut (AdapterInfo);\r
-\r
- //\r
- // eeprom control reg bits: x,x,x,x,DO,DI,CS,SK\r
- // to write the opcode+data value out one bit at a time in DI starting at msb\r
- // and then out a 1 to sk, wait, out 0 to SK and wait\r
- // repeat this for all the bits to be written\r
- //\r
-\r
- //\r
- // 11110010b\r
- //\r
- Tmp = (UINT8) (InByte (AdapterInfo, EEAddr) & 0xF2);\r
- OutByte (AdapterInfo, (UINT8) (Tmp | EE_CS), EEAddr);\r
-\r
- //\r
- // 3 for the read opcode 110b\r
- //\r
- shift_bits_out (AdapterInfo, ReadCmd, (UINT8) (3 + AddrLen));\r
-\r
- //\r
- // read the eeprom word one bit at a time\r
- //\r
- RetVal = shift_bits_in (AdapterInfo);\r
-\r
- //\r
- // Terminate the EEPROM access and leave eeprom in a clean state.\r
- //\r
- Tmp = InByte (AdapterInfo, EEAddr);\r
- Tmp &= ~(EE_CS | EE_DI);\r
- OutByte (AdapterInfo, Tmp, EEAddr);\r
-\r
- //\r
- // raise the clock and lower the eeprom shift clock\r
- //\r
- OutByte (AdapterInfo, (UINT8) (Tmp | EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (100);\r
-\r
- OutByte (AdapterInfo, (UINT8) (Tmp &~EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (100);\r
-\r
- //\r
- // giveup access to the eeprom\r
- //\r
- E100bReSetEepromLockOut (AdapterInfo);\r
-\r
- return RetVal;\r
-}\r
-\r
-UINT8\r
-E100bGetEepromAddrLen (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- Using the NIC data structure information, read the EEPROM to determine how many bits of address length\r
- this EEPROM is in Words.\r
-\r
-Arguments:\r
- AdapterInfo - Pointer to the NIC data structure information which the UNDI driver is layering on..\r
-\r
-Returns:\r
- RetVal - The word read from the EEPROM.\r
-\r
---*/\r
-{\r
- UINT8 Tmp;\r
- UINT8 AddrLen;\r
- UINT32 EEAddr;\r
- //\r
- // assume 64word eeprom (so,6 bits of address_length)\r
- //\r
- UINT16 ReadCmd;\r
-\r
- EEAddr = AdapterInfo->ioaddr + SCBeeprom;\r
- ReadCmd = (EE_READ_CMD << 6);\r
-\r
- //\r
- // get exclusive access to the eeprom first!\r
- //\r
- E100bSetEepromLockOut (AdapterInfo);\r
-\r
- //\r
- // address we are trying to read is 0\r
- // eeprom control reg bits: x,x,x,x,DO,,DI,,CS,SK\r
- // to write the opcode+data value out one bit at a time in DI starting at msb\r
- // and then out a 1 to sk, wait, out 0 to SK and wait\r
- // repeat this for all the bits to be written\r
- //\r
- Tmp = (UINT8) (InByte (AdapterInfo, EEAddr) & 0xF2);\r
-\r
- //\r
- // enable eeprom access\r
- //\r
- OutByte (AdapterInfo, (UINT8) (Tmp | EE_CS), EEAddr);\r
-\r
- //\r
- // 3 for opcode, 6 for the default address len\r
- //\r
- shift_bits_out (AdapterInfo, ReadCmd, (UINT8) (3 + 6));\r
-\r
- //\r
- // (in case of a 64 word eeprom).\r
- // read the "dummy zero" from EE_DO to say that the address we wrote\r
- // (six 0s) is accepted, write more zeros (until 8) to get a "dummy zero"\r
- //\r
-\r
- //\r
- // assume the smallest\r
- //\r
- AddrLen = 6;\r
- Tmp = InByte (AdapterInfo, EEAddr);\r
- while ((AddrLen < 8) && ((Tmp & EE_DO) != 0)) {\r
- OutByte (AdapterInfo, (UINT8) (Tmp &~EE_DI), EEAddr);\r
- eeprom_delay (100);\r
-\r
- //\r
- // raise the eeprom clock\r
- //\r
- OutByte (AdapterInfo, (UINT8) (Tmp | EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (150);\r
-\r
- //\r
- // lower the eeprom clock\r
- //\r
- OutByte (AdapterInfo, (UINT8) (Tmp &~EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (150);\r
- Tmp = InByte (AdapterInfo, EEAddr);\r
- AddrLen++;\r
- }\r
-\r
- //\r
- // read the eeprom word, even though we don't need this\r
- //\r
- shift_bits_in (AdapterInfo);\r
-\r
- //\r
- // Terminate the EEPROM access.\r
- //\r
- Tmp = InByte (AdapterInfo, EEAddr);\r
- Tmp &= ~(EE_CS | EE_DI);\r
- OutByte (AdapterInfo, Tmp, EEAddr);\r
-\r
- //\r
- // raise the clock and lower the eeprom shift clock\r
- //\r
- OutByte (AdapterInfo, (UINT8) (Tmp | EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (100);\r
-\r
- OutByte (AdapterInfo, (UINT8) (Tmp &~EE_SHIFT_CLK), EEAddr);\r
- eeprom_delay (100);\r
-\r
- //\r
- // giveup access to the eeprom!\r
- //\r
- E100bReSetEepromLockOut (AdapterInfo);\r
-\r
- return AddrLen;\r
-}\r
-\r
-UINTN\r
-E100bStatistics (\r
- NIC_DATA_INSTANCE *AdapterInfo,\r
- UINT64 DBaddr,\r
- UINT16 DBsize\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- DBaddr - TODO: add argument description\r
- DBsize - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- PXE_DB_STATISTICS db;\r
- //\r
- // wait upto one second (each wait is 100 micro s)\r
- //\r
- UINT32 Wait;\r
- Wait = 10000;\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
-\r
- //\r
- // Clear statistics done marker.\r
- //\r
- AdapterInfo->statistics->done_marker = 0;\r
-\r
- //\r
- // Issue statistics dump (or dump w/ reset) command.\r
- //\r
- OutByte (\r
- AdapterInfo,\r
- (UINT8) (DBsize ? CU_SHOWSTATS : CU_DUMPSTATS),\r
- (UINT32) (AdapterInfo->ioaddr + SCBCmd)\r
- );\r
-\r
- //\r
- // Wait for command to complete.\r
- //\r
- // zero the db here just to chew up a little more time.\r
- //\r
-\r
- ZeroMem ((VOID *) &db, sizeof db);\r
-\r
- while (Wait != 0) {\r
- //\r
- // Wait a bit before checking.\r
- //\r
-\r
- DelayIt (AdapterInfo, 100);\r
-\r
- //\r
- // Look for done marker at end of statistics.\r
- //\r
-\r
- switch (AdapterInfo->statistics->done_marker) {\r
- case 0xA005:\r
- case 0xA007:\r
- break;\r
-\r
- default:\r
- Wait--;\r
- continue;\r
- }\r
-\r
- //\r
- // if we did not "continue" from the above switch, we are done,\r
- //\r
- break;\r
- }\r
-\r
- //\r
- // If this is a reset, we are out of here!\r
- //\r
- if (DBsize == 0) {\r
- return PXE_STATCODE_SUCCESS;\r
- }\r
-\r
- //\r
- // Convert NIC statistics counter format to EFI/UNDI\r
- // specification statistics counter format.\r
- //\r
-\r
- //\r
- // 54 3210 fedc ba98 7654 3210\r
- // db.Supported = 01 0000 0100 1101 0001 0111;\r
- //\r
- db.Supported = 0x104D17;\r
-\r
- //\r
- // Statistics from the NIC\r
- //\r
-\r
- db.Data[0x01] = AdapterInfo->statistics->rx_good_frames;\r
-\r
- db.Data[0x02] = AdapterInfo->statistics->rx_runt_errs;\r
-\r
- db.Data[0x08] = AdapterInfo->statistics->rx_crc_errs +\r
- AdapterInfo->statistics->rx_align_errs;\r
-\r
- db.Data[0x04] = db.Data[0x02] + \r
- db.Data[0x08] +\r
- AdapterInfo->statistics->rx_resource_errs +\r
- AdapterInfo->statistics->rx_overrun_errs;\r
-\r
- db.Data[0x00] = db.Data[0x01] + db.Data[0x04];\r
-\r
- db.Data[0x0B] = AdapterInfo->statistics->tx_good_frames;\r
-\r
- db.Data[0x0E] = AdapterInfo->statistics->tx_coll16_errs +\r
- AdapterInfo->statistics->tx_late_colls +\r
- AdapterInfo->statistics->tx_underruns +\r
- AdapterInfo->statistics->tx_one_colls +\r
- AdapterInfo->statistics->tx_multi_colls;\r
-\r
- db.Data[0x14] = AdapterInfo->statistics->tx_total_colls;\r
-\r
- db.Data[0x0A] = db.Data[0x0B] +\r
- db.Data[0x0E] +\r
- AdapterInfo->statistics->tx_lost_carrier;\r
-\r
- if (DBsize > sizeof db) {\r
- DBsize = sizeof db;\r
- }\r
-\r
- CopyMem ((VOID *) (UINTN) DBaddr, (VOID *) &db, (UINTN) DBsize);\r
-\r
- return PXE_STATCODE_SUCCESS;\r
-}\r
-\r
-UINTN\r
-E100bReset (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN INT32 OpFlags\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
- OpFlags - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
-\r
- UINT16 save_filter;\r
- //\r
- // disable the interrupts\r
- //\r
- OutWord (AdapterInfo, INT_MASK, AdapterInfo->ioaddr + SCBCmd);\r
-\r
- //\r
- // wait for the tx queue to complete\r
- //\r
- CheckCBList (AdapterInfo);\r
-\r
- XmitWaitForCompletion (AdapterInfo);\r
-\r
- if (AdapterInfo->Receive_Started) {\r
- StopRU (AdapterInfo);\r
- }\r
-\r
- InitializeChip (AdapterInfo);\r
-\r
- //\r
- // check the opflags and restart receive filters\r
- //\r
- if ((OpFlags & PXE_OPFLAGS_RESET_DISABLE_FILTERS) == 0) {\r
-\r
- save_filter = AdapterInfo->Rx_Filter;\r
- //\r
- // if we give the filter same as Rx_Filter,\r
- // this routine will not set mcast list (it thinks there is no change)\r
- // to force it, we will reset that flag in the Rx_Filter\r
- //\r
- AdapterInfo->Rx_Filter &= (~PXE_OPFLAGS_RECEIVE_FILTER_FILTERED_MULTICAST);\r
- E100bSetfilter (AdapterInfo, save_filter, (UINT64) 0, (UINT32) 0);\r
- }\r
-\r
- if ((OpFlags & PXE_OPFLAGS_RESET_DISABLE_INTERRUPTS) != 0) {\r
- //\r
- // disable the interrupts\r
- //\r
- AdapterInfo->int_mask = 0;\r
- }\r
- //\r
- // else leave the interrupt in the pre-set state!!!\r
- //\r
- E100bSetInterruptState (AdapterInfo);\r
-\r
- return 0;\r
-}\r
-\r
-UINTN\r
-E100bShutdown (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- //\r
- // disable the interrupts\r
- //\r
- OutWord (AdapterInfo, INT_MASK, AdapterInfo->ioaddr + SCBCmd);\r
-\r
- //\r
- // stop the receive unit\r
- //\r
- if (AdapterInfo->Receive_Started) {\r
- StopRU (AdapterInfo);\r
- }\r
-\r
- //\r
- // wait for the tx queue to complete\r
- //\r
- CheckCBList (AdapterInfo);\r
- if (AdapterInfo->FreeCBCount != AdapterInfo->TxBufCnt) {\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
- }\r
-\r
- //\r
- // we do not want to reset the phy, it takes a long time to renegotiate the\r
- // link after that (3-4 seconds)\r
- //\r
- InitializeChip (AdapterInfo);\r
- SelectiveReset (AdapterInfo);\r
- return 0;\r
-}\r
-\r
-VOID\r
-MdiWrite (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT8 RegAddress,\r
- IN UINT8 PhyAddress,\r
- IN UINT16 DataValue\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This routine will write a value to the specified MII register\r
- of an external MDI compliant device (e.g. PHY 100). The command will \r
- execute in polled mode.\r
- \r
-Arguments:\r
- AdapterInfo - pointer to the structure that contains the NIC's context.\r
- RegAddress - The MII register that we are writing to\r
- PhyAddress - The MDI address of the Phy component.\r
- DataValue - The value that we are writing to the MII register.\r
-\r
-Returns:\r
- nothing \r
---*/\r
-{\r
- UINT32 WriteCommand;\r
-\r
- WriteCommand = ((UINT32) DataValue) |\r
- ((UINT32)(RegAddress << 16)) | \r
- ((UINT32)(PhyAddress << 21)) |\r
- ((UINT32)(MDI_WRITE << 26));\r
-\r
- //\r
- // Issue the write command to the MDI control register.\r
- //\r
- OutLong (AdapterInfo, WriteCommand, AdapterInfo->ioaddr + SCBCtrlMDI);\r
-\r
- //\r
- // wait 20usec before checking status\r
- //\r
- DelayIt (AdapterInfo, 20);\r
-\r
- //\r
- // poll for the mdi write to complete\r
- while ((InLong (AdapterInfo, AdapterInfo->ioaddr + SCBCtrlMDI) & \r
- MDI_PHY_READY) == 0){\r
- DelayIt (AdapterInfo, 20);\r
- }\r
-}\r
-\r
-VOID\r
-MdiRead (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT8 RegAddress,\r
- IN UINT8 PhyAddress,\r
- IN OUT UINT16 *DataValue\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This routine will read a value from the specified MII register\r
- of an external MDI compliant device (e.g. PHY 100), and return\r
- it to the calling routine. The command will execute in polled mode.\r
- \r
-Arguments:\r
- AdapterInfo - pointer to the structure that contains the NIC's context.\r
- RegAddress - The MII register that we are reading from\r
- PhyAddress - The MDI address of the Phy component.\r
- DataValue - pointer to the value that we read from the MII register.\r
-\r
-Returns:\r
- \r
---*/\r
-{\r
- UINT32 ReadCommand;\r
-\r
- ReadCommand = ((UINT32) (RegAddress << 16)) |\r
- ((UINT32) (PhyAddress << 21)) |\r
- ((UINT32) (MDI_READ << 26));\r
-\r
- //\r
- // Issue the read command to the MDI control register.\r
- //\r
- OutLong (AdapterInfo, ReadCommand, AdapterInfo->ioaddr + SCBCtrlMDI);\r
-\r
- //\r
- // wait 20usec before checking status\r
- //\r
- DelayIt (AdapterInfo, 20);\r
-\r
- //\r
- // poll for the mdi read to complete\r
- //\r
- while ((InLong (AdapterInfo, AdapterInfo->ioaddr + SCBCtrlMDI) &\r
- MDI_PHY_READY) == 0) {\r
- DelayIt (AdapterInfo, 20);\r
-\r
- }\r
-\r
- *DataValue = InWord (AdapterInfo, AdapterInfo->ioaddr + SCBCtrlMDI);\r
-}\r
-\r
-VOID\r
-PhyReset (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This routine will reset the PHY that the adapter is currently\r
- configured to use. \r
- \r
-Arguments:\r
- AdapterInfo - pointer to the structure that contains the NIC's context.\r
-\r
-Returns:\r
- \r
---*/\r
-{\r
- UINT16 MdiControlReg;\r
-\r
- MdiControlReg = (MDI_CR_AUTO_SELECT | \r
- MDI_CR_RESTART_AUTO_NEG | \r
- MDI_CR_RESET);\r
-\r
- //\r
- // Write the MDI control register with our new Phy configuration\r
- //\r
- MdiWrite (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- MdiControlReg\r
- );\r
-\r
- return ;\r
-}\r
-\r
-BOOLEAN\r
-PhyDetect (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This routine will detect what phy we are using, set the line\r
- speed, FDX or HDX, and configure the phy if necessary.\r
-\r
- The following combinations are supported:\r
- - TX or T4 PHY alone at PHY address 1\r
- - T4 or TX PHY at address 1 and MII PHY at address 0\r
- - 82503 alone (10Base-T mode, no full duplex support)\r
- - 82503 and MII PHY (TX or T4) at address 0\r
-\r
- The sequence / priority of detection is as follows:\r
- - PHY 1 with cable termination\r
- - PHY 0 with cable termination\r
- - PHY 1 (if found) without cable termination\r
- - 503 interface\r
-\r
- Additionally auto-negotiation capable (NWAY) and parallel\r
- detection PHYs are supported. The flow-chart is described in\r
- the 82557 software writer's manual.\r
-\r
- NOTE: 1. All PHY MDI registers are read in polled mode.\r
- 2. The routines assume that the 82557 has been RESET and we have\r
- obtained the virtual memory address of the CSR.\r
- 3. PhyDetect will not RESET the PHY.\r
- 4. If FORCEFDX is set, SPEED should also be set. The driver will\r
- check the values for inconsistency with the detected PHY\r
- technology.\r
- 5. PHY 1 (the PHY on the adapter) may have an address in the range\r
- 1 through 31 inclusive. The driver will accept addresses in\r
- this range.\r
- 6. Driver ignores FORCEFDX and SPEED overrides if a 503 interface\r
- is detected.\r
- \r
-Arguments:\r
- AdapterInfo - pointer to the structure that contains the NIC's context.\r
-\r
-Returns:\r
- TRUE - If a Phy was detected, and configured correctly.\r
- FALSE - If a valid phy could not be detected and configured. \r
- \r
---*/\r
-{\r
- UINT16 *eedata;\r
- UINT16 MdiControlReg;\r
- UINT16 MdiStatusReg;\r
- BOOLEAN FoundPhy1;\r
- UINT8 ReNegotiateTime;\r
-\r
- eedata = (UINT16 *) (&AdapterInfo->NVData[0]);\r
-\r
- FoundPhy1 = FALSE;\r
- ReNegotiateTime = 35;\r
- //\r
- // EEPROM word [6] contains the Primary PHY record in which the least 3 bits\r
- // indicate the PHY address\r
- // and word [7] contains the secondary PHY record\r
- //\r
- AdapterInfo->PhyRecord[0] = eedata[6];\r
- AdapterInfo->PhyRecord[1] = eedata[7];\r
- AdapterInfo->PhyAddress = (UINT8) (AdapterInfo->PhyRecord[0] & 7);\r
-\r
- //\r
- // Check for a phy address over-ride of 32 which indicates force use of 82503\r
- // not detecting the link in this case\r
- //\r
- if (AdapterInfo->PhyAddress == 32) {\r
- //\r
- // 503 interface over-ride\r
- // Record the current speed and duplex. We will be in half duplex\r
- // mode unless the user used the force full duplex over-ride.\r
- //\r
- AdapterInfo->LinkSpeed = 10;\r
- return (TRUE);\r
- }\r
-\r
- //\r
- // If the Phy Address is between 1-31 then we must first look for phy 1,\r
- // at that address.\r
- //\r
- if ((AdapterInfo->PhyAddress > 0) && (AdapterInfo->PhyAddress < 32)) {\r
-\r
- //\r
- // Read the MDI control and status registers at phy 1\r
- // and check if we found a valid phy\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiControlReg\r
- );\r
-\r
- MdiRead (\r
- AdapterInfo,\r
- MDI_STATUS_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiStatusReg\r
- );\r
-\r
- if (!((MdiControlReg == 0xffff) || \r
- ((MdiStatusReg == 0) && (MdiControlReg == 0)))) {\r
-\r
- //\r
- // we have a valid phy1\r
- // Read the status register again because of sticky bits\r
- //\r
- FoundPhy1 = TRUE;\r
- MdiRead (\r
- AdapterInfo,\r
- MDI_STATUS_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiStatusReg\r
- );\r
-\r
- //\r
- // If there is a valid link then use this Phy.\r
- //\r
- if (MdiStatusReg & MDI_SR_LINK_STATUS) {\r
- return (SetupPhy(AdapterInfo));\r
- }\r
- }\r
- }\r
-\r
- //\r
- // Next try to detect a PHY at address 0x00 because there was no Phy 1,\r
- // or Phy 1 didn't have link, or we had a phy 0 over-ride\r
- //\r
-\r
- //\r
- // Read the MDI control and status registers at phy 0\r
- //\r
- MdiRead (AdapterInfo, MDI_CONTROL_REG, 0, &MdiControlReg);\r
- MdiRead (AdapterInfo, MDI_STATUS_REG, 0, &MdiStatusReg);\r
-\r
- //\r
- // check if we found a valid phy 0\r
- //\r
- if (((MdiControlReg == 0xffff) ||\r
- ((MdiStatusReg == 0) && (MdiControlReg == 0)))) {\r
-\r
- //\r
- // we don't have a valid phy at address 0\r
- // if phy address was forced to 0, then error out because we\r
- // didn't find a phy at that address\r
- //\r
- if (AdapterInfo->PhyAddress == 0x0000) {\r
- return (FALSE);\r
- } else {\r
- //\r
- // at this point phy1 does not have link and there is no phy 0 at all\r
- // if we are forced to detect the cable, error out here!\r
- //\r
- if (AdapterInfo->CableDetect != 0) {\r
- return FALSE;\r
-\r
- }\r
-\r
- if (FoundPhy1) {\r
- //\r
- // no phy 0, but there is a phy 1 (no link I guess), so use phy 1\r
- //\r
- return SetupPhy (AdapterInfo);\r
- } else {\r
- //\r
- // didn't find phy 0 or phy 1, so assume a 503 interface\r
- //\r
- AdapterInfo->PhyAddress = 32;\r
-\r
- //\r
- // Record the current speed and duplex. We'll be in half duplex\r
- // mode unless the user used the force full duplex over-ride.\r
- //\r
- AdapterInfo->LinkSpeed = 10;\r
- return (TRUE);\r
- }\r
- }\r
- } else {\r
- //\r
- // We have a valid phy at address 0. If phy 0 has a link then we use\r
- // phy 0. If Phy 0 doesn't have a link then we use Phy 1 (no link)\r
- // if phy 1 is present, or phy 0 if phy 1 is not present\r
- // If phy 1 was present, then we must isolate phy 1 before we enable\r
- // phy 0 to see if Phy 0 has a link.\r
- //\r
- if (FoundPhy1) {\r
- //\r
- // isolate phy 1\r
- //\r
- MdiWrite (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- MDI_CR_ISOLATE\r
- );\r
-\r
- //\r
- // wait 100 microseconds for the phy to isolate.\r
- //\r
- DelayIt (AdapterInfo, 100);\r
- }\r
-\r
- //\r
- // Since this Phy is at address 0, we must enable it. So clear\r
- // the isolate bit, and set the auto-speed select bit\r
- //\r
- MdiWrite (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- 0,\r
- MDI_CR_AUTO_SELECT\r
- );\r
-\r
- //\r
- // wait 100 microseconds for the phy to be enabled.\r
- //\r
- DelayIt (AdapterInfo, 100);\r
-\r
- //\r
- // restart the auto-negotion process\r
- //\r
- MdiWrite (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- 0,\r
- MDI_CR_RESTART_AUTO_NEG | MDI_CR_AUTO_SELECT\r
- );\r
-\r
- //\r
- // wait no more than 3.5 seconds for auto-negotiation to complete\r
- //\r
- while (ReNegotiateTime) {\r
- //\r
- // Read the status register twice because of sticky bits\r
- //\r
- MdiRead (AdapterInfo, MDI_STATUS_REG, 0, &MdiStatusReg);\r
- MdiRead (AdapterInfo, MDI_STATUS_REG, 0, &MdiStatusReg);\r
-\r
- if (MdiStatusReg & MDI_SR_AUTO_NEG_COMPLETE) {\r
- break;\r
- }\r
-\r
- DelayIt (AdapterInfo, 100);\r
- ReNegotiateTime--;\r
- }\r
-\r
- //\r
- // Read the status register again because of sticky bits\r
- //\r
- MdiRead (AdapterInfo, MDI_STATUS_REG, 0, &MdiStatusReg);\r
-\r
- //\r
- // If the link was not set\r
- //\r
- if ((MdiStatusReg & MDI_SR_LINK_STATUS) == 0) {\r
- //\r
- // PHY1 does not have a link and phy 0 does not have a link\r
- // do not proceed if we need to detect the link!\r
- //\r
- if (AdapterInfo->CableDetect != 0) {\r
- return FALSE;\r
- }\r
-\r
- //\r
- // the link wasn't set, so use phy 1 if phy 1 was present\r
- //\r
- if (FoundPhy1) {\r
- //\r
- // isolate phy 0\r
- //\r
- MdiWrite (AdapterInfo, MDI_CONTROL_REG, 0, MDI_CR_ISOLATE);\r
-\r
- //\r
- // wait 100 microseconds for the phy to isolate.\r
- //\r
- DelayIt (AdapterInfo, 100);\r
-\r
- //\r
- // Now re-enable PHY 1\r
- //\r
- MdiWrite (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- MDI_CR_AUTO_SELECT\r
- );\r
-\r
- //\r
- // wait 100 microseconds for the phy to be enabled\r
- //\r
- DelayIt (AdapterInfo, 100);\r
-\r
- //\r
- // restart the auto-negotion process\r
- //\r
- MdiWrite (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- MDI_CR_RESTART_AUTO_NEG | MDI_CR_AUTO_SELECT\r
- );\r
-\r
- //\r
- // Don't wait for it to complete (we didn't have link earlier)\r
- //\r
- return (SetupPhy (AdapterInfo));\r
- }\r
- }\r
-\r
- //\r
- // Definitely using Phy 0\r
- //\r
- AdapterInfo->PhyAddress = 0;\r
- return (SetupPhy(AdapterInfo));\r
- }\r
-}\r
-\r
-BOOLEAN\r
-SetupPhy (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This routine will setup phy 1 or phy 0 so that it is configured\r
- to match a speed and duplex over-ride option. If speed or\r
- duplex mode is not explicitly specified in the registry, the\r
- driver will skip the speed and duplex over-ride code, and\r
- assume the adapter is automatically setting the line speed, and\r
- the duplex mode. At the end of this routine, any truly Phy\r
- specific code will be executed (each Phy has its own quirks,\r
- and some require that certain special bits are set).\r
-\r
- NOTE: The driver assumes that SPEED and FORCEFDX are specified at the\r
- same time. If FORCEDPX is set without speed being set, the driver\r
- will encouter a fatal error and log a message into the event viewer.\r
-\r
-Arguments:\r
- AdapterInfo - pointer to the structure that contains the NIC's context.\r
-\r
-Returns:\r
- TRUE - If the phy could be configured correctly\r
- FALSE - If the phy couldn't be configured correctly, because an \r
- unsupported over-ride option was used\r
- \r
---*/\r
-{\r
- UINT16 MdiControlReg;\r
- UINT16 MdiStatusReg;\r
- UINT16 MdiIdLowReg;\r
- UINT16 MdiIdHighReg;\r
- UINT16 MdiMiscReg;\r
- UINT32 PhyId;\r
- BOOLEAN ForcePhySetting;\r
-\r
- ForcePhySetting = FALSE;\r
-\r
- //\r
- // If we are NOT forcing a setting for line speed or full duplex, then\r
- // we won't force a link setting, and we'll jump down to the phy\r
- // specific code.\r
- //\r
- if (((AdapterInfo->LinkSpeedReq) || (AdapterInfo->DuplexReq))) {\r
- //\r
- // Find out what kind of technology this Phy is capable of.\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- MDI_STATUS_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiStatusReg\r
- );\r
-\r
- //\r
- // Read the MDI control register at our phy\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiControlReg\r
- );\r
-\r
- //\r
- // Now check the validity of our forced option. If the force option is\r
- // valid, then force the setting. If the force option is not valid,\r
- // we'll set a flag indicating that we should error out.\r
- //\r
-\r
- //\r
- // If speed is forced to 10mb\r
- //\r
- if (AdapterInfo->LinkSpeedReq == 10) {\r
- //\r
- // If half duplex is forced\r
- //\r
- if ((AdapterInfo->DuplexReq & PXE_FORCE_HALF_DUPLEX) != 0) {\r
- if (MdiStatusReg & MDI_SR_10T_HALF_DPX) {\r
-\r
- MdiControlReg &= ~(MDI_CR_10_100 | MDI_CR_AUTO_SELECT | MDI_CR_FULL_HALF);\r
- ForcePhySetting = TRUE;\r
- }\r
- } else if ((AdapterInfo->DuplexReq & PXE_FORCE_FULL_DUPLEX) != 0) {\r
-\r
- //\r
- // If full duplex is forced\r
- //\r
- if (MdiStatusReg & MDI_SR_10T_FULL_DPX) {\r
-\r
- MdiControlReg &= ~(MDI_CR_10_100 | MDI_CR_AUTO_SELECT);\r
- MdiControlReg |= MDI_CR_FULL_HALF;\r
- ForcePhySetting = TRUE;\r
- }\r
- } else {\r
- //\r
- // If auto duplex (we actually set phy to 1/2)\r
- //\r
- if (MdiStatusReg & (MDI_SR_10T_FULL_DPX | MDI_SR_10T_HALF_DPX)) {\r
-\r
- MdiControlReg &= ~(MDI_CR_10_100 | MDI_CR_AUTO_SELECT | MDI_CR_FULL_HALF);\r
- ForcePhySetting = TRUE;\r
- }\r
- }\r
- }\r
-\r
- //\r
- // If speed is forced to 100mb\r
- //\r
- else if (AdapterInfo->LinkSpeedReq == 100) {\r
- //\r
- // If half duplex is forced\r
- //\r
- if ((AdapterInfo->DuplexReq & PXE_FORCE_HALF_DUPLEX) != 0) {\r
- if (MdiStatusReg & (MDI_SR_TX_HALF_DPX | MDI_SR_T4_CAPABLE)) {\r
-\r
- MdiControlReg &= ~(MDI_CR_AUTO_SELECT | MDI_CR_FULL_HALF);\r
- MdiControlReg |= MDI_CR_10_100;\r
- ForcePhySetting = TRUE;\r
- }\r
- } else if ((AdapterInfo->DuplexReq & PXE_FORCE_FULL_DUPLEX) != 0) {\r
- //\r
- // If full duplex is forced\r
- //\r
- if (MdiStatusReg & MDI_SR_TX_FULL_DPX) {\r
- MdiControlReg &= ~MDI_CR_AUTO_SELECT;\r
- MdiControlReg |= (MDI_CR_10_100 | MDI_CR_FULL_HALF);\r
- ForcePhySetting = TRUE;\r
- }\r
- } else {\r
- //\r
- // If auto duplex (we set phy to 1/2)\r
- //\r
- if (MdiStatusReg & (MDI_SR_TX_HALF_DPX | MDI_SR_T4_CAPABLE)) {\r
-\r
- MdiControlReg &= ~(MDI_CR_AUTO_SELECT | MDI_CR_FULL_HALF);\r
- MdiControlReg |= MDI_CR_10_100;\r
- ForcePhySetting = TRUE;\r
- }\r
- }\r
- }\r
-\r
- if (!ForcePhySetting) {\r
- return (FALSE);\r
- }\r
-\r
- //\r
- // Write the MDI control register with our new Phy configuration\r
- //\r
- MdiWrite (\r
- AdapterInfo,\r
- MDI_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- MdiControlReg\r
- );\r
-\r
- //\r
- // wait 100 milliseconds for auto-negotiation to complete\r
- //\r
- DelayIt (AdapterInfo, 100);\r
- }\r
-\r
- //\r
- // Find out specifically what Phy this is. We do this because for certain\r
- // phys there are specific bits that must be set so that the phy and the\r
- // 82557 work together properly.\r
- //\r
-\r
- MdiRead (\r
- AdapterInfo,\r
- PHY_ID_REG_1,\r
- AdapterInfo->PhyAddress,\r
- &MdiIdLowReg\r
- );\r
- MdiRead (\r
- AdapterInfo,\r
- PHY_ID_REG_2,\r
- AdapterInfo->PhyAddress,\r
- &MdiIdHighReg\r
- );\r
-\r
- PhyId = ((UINT32) MdiIdLowReg | ((UINT32) MdiIdHighReg << 16));\r
-\r
- //\r
- // And out the revsion field of the Phy ID so that we'll be able to detect\r
- // future revs of the same Phy.\r
- //\r
- PhyId &= PHY_MODEL_REV_ID_MASK;\r
-\r
- //\r
- // Handle the National TX\r
- //\r
- if (PhyId == PHY_NSC_TX) {\r
-\r
- MdiRead (\r
- AdapterInfo,\r
- NSC_CONG_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiMiscReg\r
- );\r
-\r
- MdiMiscReg |= (NSC_TX_CONG_TXREADY | NSC_TX_CONG_F_CONNECT);\r
-\r
- MdiWrite (\r
- AdapterInfo,\r
- NSC_CONG_CONTROL_REG,\r
- AdapterInfo->PhyAddress,\r
- MdiMiscReg\r
- );\r
- }\r
-\r
- FindPhySpeedAndDpx (AdapterInfo, PhyId);\r
-\r
- //\r
- // We put a hardware fix on to our adapters to work-around the PHY_100 errata\r
- // described below. The following code is only compiled in, if we wanted\r
- // to attempt a software workaround to the PHY_100 A/B step problem.\r
- //\r
-\r
- return (TRUE);\r
-}\r
-\r
-VOID\r
-FindPhySpeedAndDpx (\r
- IN NIC_DATA_INSTANCE *AdapterInfo,\r
- IN UINT32 PhyId\r
- )\r
-/*++\r
-\r
-Routine Description:\r
- This routine will figure out what line speed and duplex mode\r
- the PHY is currently using.\r
-\r
-Arguments:\r
- AdapterInfo - pointer to the structure that contains the NIC's context.\r
- PhyId - The ID of the PHY in question.\r
-\r
-Returns:\r
- NOTHING\r
---*/\r
-{\r
- UINT16 MdiStatusReg;\r
- UINT16 MdiMiscReg;\r
- UINT16 MdiOwnAdReg;\r
- UINT16 MdiLinkPartnerAdReg;\r
-\r
- //\r
- // If there was a speed and/or duplex override, then set our current\r
- // value accordingly\r
- //\r
- AdapterInfo->LinkSpeed = AdapterInfo->LinkSpeedReq;\r
- AdapterInfo->Duplex = (UINT8) ((AdapterInfo->DuplexReq & PXE_FORCE_FULL_DUPLEX) ? \r
- FULL_DUPLEX : HALF_DUPLEX);\r
-\r
- //\r
- // If speed and duplex were forced, then we know our current settings, so\r
- // we'll just return. Otherwise, we'll need to figure out what NWAY set\r
- // us to.\r
- //\r
- if (AdapterInfo->LinkSpeed && AdapterInfo->Duplex) {\r
- return ;\r
-\r
- }\r
- //\r
- // If we didn't have a valid link, then we'll assume that our current\r
- // speed is 10mb half-duplex.\r
- //\r
-\r
- //\r
- // Read the status register twice because of sticky bits\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- MDI_STATUS_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiStatusReg\r
- );\r
- MdiRead (\r
- AdapterInfo,\r
- MDI_STATUS_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiStatusReg\r
- );\r
-\r
- //\r
- // If there wasn't a valid link then use default speed & duplex\r
- //\r
- if (!(MdiStatusReg & MDI_SR_LINK_STATUS)) {\r
-\r
- AdapterInfo->LinkSpeed = 10;\r
- AdapterInfo->Duplex = HALF_DUPLEX;\r
- return ;\r
- }\r
-\r
- //\r
- // If this is an Intel PHY (a T4 PHY_100 or a TX PHY_TX), then read bits\r
- // 1 and 0 of extended register 0, to get the current speed and duplex\r
- // settings.\r
- //\r
- if ((PhyId == PHY_100_A) || (PhyId == PHY_100_C) || (PhyId == PHY_TX_ID)) {\r
- //\r
- // Read extended register 0\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- EXTENDED_REG_0,\r
- AdapterInfo->PhyAddress,\r
- &MdiMiscReg\r
- );\r
-\r
- //\r
- // Get current speed setting\r
- //\r
- if (MdiMiscReg & PHY_100_ER0_SPEED_INDIC) {\r
- AdapterInfo->LinkSpeed = 100;\r
- } else {\r
- AdapterInfo->LinkSpeed = 10;\r
- }\r
-\r
- //\r
- // Get current duplex setting -- if bit is set then FDX is enabled\r
- //\r
- if (MdiMiscReg & PHY_100_ER0_FDX_INDIC) {\r
- AdapterInfo->Duplex = FULL_DUPLEX;\r
- } else {\r
- AdapterInfo->Duplex = HALF_DUPLEX;\r
- }\r
-\r
- return ;\r
- }\r
- //\r
- // Read our link partner's advertisement register\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- AUTO_NEG_LINK_PARTNER_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiLinkPartnerAdReg\r
- );\r
-\r
- //\r
- // See if Auto-Negotiation was complete (bit 5, reg 1)\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- MDI_STATUS_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiStatusReg\r
- );\r
-\r
- //\r
- // If a True NWAY connection was made, then we can detect speed/duplex by\r
- // ANDing our adapter's advertised abilities with our link partner's\r
- // advertised ablilities, and then assuming that the highest common\r
- // denominator was chosed by NWAY.\r
- //\r
- if ((MdiLinkPartnerAdReg & NWAY_LP_ABILITY) && \r
- (MdiStatusReg & MDI_SR_AUTO_NEG_COMPLETE)) {\r
-\r
- //\r
- // Read our advertisement register\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- AUTO_NEG_ADVERTISE_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiOwnAdReg\r
- );\r
-\r
- //\r
- // AND the two advertisement registers together, and get rid of any\r
- // extraneous bits.\r
- //\r
- MdiOwnAdReg = (UINT16) (MdiOwnAdReg & (MdiLinkPartnerAdReg & NWAY_LP_ABILITY));\r
-\r
- //\r
- // Get speed setting\r
- //\r
- if (MdiOwnAdReg & (NWAY_AD_TX_HALF_DPX | NWAY_AD_TX_FULL_DPX | NWAY_AD_T4_CAPABLE)) {\r
- AdapterInfo->LinkSpeed = 100;\r
- } else {\r
- AdapterInfo->LinkSpeed = 10;\r
- }\r
-\r
- //\r
- // Get duplex setting -- use priority resolution algorithm\r
- //\r
- if (MdiOwnAdReg & (NWAY_AD_T4_CAPABLE)) {\r
- AdapterInfo->Duplex = HALF_DUPLEX;\r
- return ;\r
- } else if (MdiOwnAdReg & (NWAY_AD_TX_FULL_DPX)) {\r
- AdapterInfo->Duplex = FULL_DUPLEX;\r
- return ;\r
- } else if (MdiOwnAdReg & (NWAY_AD_TX_HALF_DPX)) {\r
- AdapterInfo->Duplex = HALF_DUPLEX;\r
- return ;\r
- } else if (MdiOwnAdReg & (NWAY_AD_10T_FULL_DPX)) {\r
- AdapterInfo->Duplex = FULL_DUPLEX;\r
- return ;\r
- } else {\r
- AdapterInfo->Duplex = HALF_DUPLEX;\r
- return ;\r
- }\r
- }\r
-\r
- //\r
- // If we are connected to a dumb (non-NWAY) repeater or hub, and the line\r
- // speed was determined automatically by parallel detection, then we have\r
- // no way of knowing exactly what speed the PHY is set to unless that PHY\r
- // has a propietary register which indicates speed in this situation. The\r
- // NSC TX PHY does have such a register. Also, since NWAY didn't establish\r
- // the connection, the duplex setting should HALF duplex.\r
- //\r
- AdapterInfo->Duplex = HALF_DUPLEX;\r
-\r
- if (PhyId == PHY_NSC_TX) {\r
- //\r
- // Read register 25 to get the SPEED_10 bit\r
- //\r
- MdiRead (\r
- AdapterInfo,\r
- NSC_SPEED_IND_REG,\r
- AdapterInfo->PhyAddress,\r
- &MdiMiscReg\r
- );\r
-\r
- //\r
- // If bit 6 was set then we're at 10mb\r
- //\r
- if (MdiMiscReg & NSC_TX_SPD_INDC_SPEED) {\r
- AdapterInfo->LinkSpeed = 10;\r
- } else {\r
- AdapterInfo->LinkSpeed = 100;\r
- }\r
- }\r
-\r
- //\r
- // If we don't know what line speed we are set at, then we'll default to\r
- // 10mbs\r
- //\r
- else {\r
- AdapterInfo->LinkSpeed = 10;\r
- }\r
-}\r
-\r
-VOID\r
-XmitWaitForCompletion (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- TxCB *TxPtr;\r
-\r
- if (AdapterInfo->FreeCBCount == AdapterInfo->TxBufCnt) {\r
- return ;\r
- }\r
-\r
- //\r
- // used xmit cb list starts right after the free tail (ends before the\r
- // free head ptr)\r
- //\r
- TxPtr = AdapterInfo->FreeTxTailPtr->NextTCBVirtualLinkPtr;\r
- while (TxPtr != AdapterInfo->FreeTxHeadPtr) {\r
- CommandWaitForCompletion (TxPtr, AdapterInfo);\r
- SetFreeCB (AdapterInfo, TxPtr);\r
- TxPtr = TxPtr->NextTCBVirtualLinkPtr;\r
- }\r
-}\r
-\r
-INT8\r
-CommandWaitForCompletion (\r
- TxCB *cmd_ptr,\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- cmd_ptr - TODO: add argument description\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- INT16 wait;\r
- wait = 5000;\r
- while ((cmd_ptr->cb_header.status == 0) && (--wait > 0)) {\r
- DelayIt (AdapterInfo, 10);\r
- }\r
-\r
- if (cmd_ptr->cb_header.status == 0) {\r
- return -1;\r
- }\r
-\r
- return 0;\r
-}\r
-\r
-STATIC\r
-INT8\r
-SoftwareReset (\r
- NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- UINT8 tco_stat;\r
- UINT16 wait;\r
-\r
- tco_stat = 0;\r
-\r
- //\r
- // Reset the chip: stop Tx and Rx processes and clear counters.\r
- // This takes less than 10usec and will easily finish before the next\r
- // action.\r
- //\r
-\r
- OutLong (AdapterInfo, PORT_RESET, AdapterInfo->ioaddr + SCBPort);\r
- //\r
- // wait for 5 milli seconds here!\r
- //\r
- DelayIt (AdapterInfo, 5000);\r
- //\r
- // TCO Errata work around for 559s only\r
- // -----------------------------------------------------------------------------------\r
- // TCO Workaround Code\r
- // haifa workaround\r
- // -----------------------------------------------------------------------------------\r
- // 1. Issue SW-RST ^^^ (already done above)\r
- // 2. Issue a redundant Set CU Base CMD immediately\r
- // Do not set the General Pointer before the Set CU Base cycle\r
- // Do not check the SCB CMD before the Set CU Base cycle\r
- // 3. Wait for the SCB-CMD to be cleared\r
- // this indicates the transition to post-driver\r
- // 4. Poll the TCO-Req bit in the PMDR to be cleared\r
- // this indicates the tco activity has stopped for real\r
- // 5. Proceed with the nominal Driver Init:\r
- // Actual Set CU & RU Base ...\r
- //\r
- // Check for ICH2 device ID. If this is an ICH2,\r
- // do the TCO workaround code.\r
- //\r
- if (AdapterInfo->VendorID == D102_DEVICE_ID ||\r
- AdapterInfo->VendorID == ICH3_DEVICE_ID_1 ||\r
- AdapterInfo->VendorID == ICH3_DEVICE_ID_2 ||\r
- AdapterInfo->VendorID == ICH3_DEVICE_ID_3 ||\r
- AdapterInfo->VendorID == ICH3_DEVICE_ID_4 ||\r
- AdapterInfo->VendorID == ICH3_DEVICE_ID_5 ||\r
- AdapterInfo->VendorID == ICH3_DEVICE_ID_6 ||\r
- AdapterInfo->VendorID == ICH3_DEVICE_ID_7 ||\r
- AdapterInfo->VendorID == ICH3_DEVICE_ID_8 ||\r
- AdapterInfo->RevID >= 8) { // do the TCO fix\r
- //\r
- // donot load the scb pointer but just give load_cu cmd.\r
- //\r
- OutByte (AdapterInfo, CU_CMD_BASE, AdapterInfo->ioaddr + SCBCmd);\r
- //\r
- // wait for command to be accepted.\r
- //\r
- wait_for_cmd_done (AdapterInfo->ioaddr + SCBCmd);\r
- //\r
- // read PMDR register and check bit 1 in it to see if TCO is active\r
- //\r
-\r
- //\r
- // wait for 5 milli seconds\r
- //\r
- wait = 5000;\r
- while (wait) {\r
- tco_stat = InByte (AdapterInfo, AdapterInfo->ioaddr + 0x1b);\r
- if ((tco_stat & 2) == 0) {\r
- //\r
- // is the activity bit clear??\r
- //\r
- break;\r
- }\r
-\r
- wait--;\r
- DelayIt (AdapterInfo, 1);\r
- }\r
-\r
- if ((tco_stat & 2) != 0) {\r
- //\r
- // not zero??\r
- //\r
- return -1;\r
- }\r
- }\r
-\r
- return 0;\r
-}\r
-\r
-UINT8\r
-SelectiveReset (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- UINT16 wait;\r
- UINT32 stat;\r
-\r
- wait = 10;\r
- stat = 0;\r
- OutLong (AdapterInfo, POR_SELECTIVE_RESET, AdapterInfo->ioaddr + SCBPort);\r
- //\r
- // wait for this to complete\r
- //\r
-\r
- //\r
- // wait for 2 milli seconds here!\r
- //\r
- DelayIt (AdapterInfo, 2000);\r
- while (wait > 0) {\r
- wait--;\r
- stat = InLong (AdapterInfo, AdapterInfo->ioaddr + SCBPort);\r
- if (stat == 0) {\r
- break;\r
- }\r
-\r
- //\r
- // wait for 1 milli second\r
- //\r
- DelayIt (AdapterInfo, 1000);\r
- }\r
-\r
- if (stat != 0) {\r
- return PXE_STATCODE_DEVICE_FAILURE;\r
- }\r
-\r
- return 0;\r
-}\r
-\r
-UINT16\r
-InitializeChip (\r
- IN NIC_DATA_INSTANCE *AdapterInfo\r
- )\r
-/*++\r
-\r
-Routine Description:\r
-\r
- TODO: Add function description\r
-\r
-Arguments:\r
-\r
- AdapterInfo - TODO: add argument description\r
-\r
-Returns:\r
-\r
- TODO: add return values\r
-\r
---*/\r
-{\r
- UINT16 ret_val;\r
- if (SoftwareReset (AdapterInfo) != 0) {\r
- return PXE_STATCODE_DEVICE_FAILURE;\r
- }\r
-\r
- //\r
- // disable interrupts\r
- //\r
- OutWord (AdapterInfo, INT_MASK, AdapterInfo->ioaddr + SCBCmd);\r
-\r
- //\r
- // Load the base registers with 0s (we will give the complete address as\r
- // offset later when we issue any command\r
- //\r
- if ((ret_val = Load_Base_Regs (AdapterInfo)) != 0) {\r
- return ret_val;\r
- }\r
-\r
- if ((ret_val = SetupCBlink (AdapterInfo)) != 0) {\r
- return ret_val;\r
- }\r
-\r
- if ((ret_val = SetupReceiveQueues (AdapterInfo)) != 0) {\r
- return ret_val;\r
- }\r
-\r
- //\r
- // detect the PHY only if we need to detect the cable as requested by the\r
- // initialize parameters\r
- //\r
- AdapterInfo->PhyAddress = 0xFF;\r
-\r
- if (AdapterInfo->CableDetect != 0) {\r
- if (!PhyDetect (AdapterInfo)) {\r
- return PXE_STATCODE_DEVICE_FAILURE;\r
- }\r
- }\r
-\r
- if ((ret_val = E100bSetupIAAddr (AdapterInfo)) != 0) {\r
- return ret_val;\r
- }\r
-\r
- if ((ret_val = Configure (AdapterInfo)) != 0) {\r
- return ret_val;\r
- }\r
-\r
- return 0;\r
-}\r