/** @file\r
TIS (TPM Interface Specification) functions used by dTPM2.0 library.\r
\r
-Copyright (c) 2013, Intel Corporation. All rights reserved.<BR>\r
+Copyright (c) 2013 - 2016, Intel Corporation. All rights reserved.<BR>\r
+(C) Copyright 2015 Hewlett Packard Enterprise Development LP<BR>\r
This program and the accompanying materials \r
are licensed and made available under the terms and conditions of the BSD License \r
which accompanies this distribution. The full text of the license may be found at \r
#include <Library/Tpm2DeviceLib.h>\r
#include <Library/PcdLib.h>\r
\r
-//\r
-// Set structure alignment to 1-byte\r
-//\r
-#pragma pack (1)\r
-\r
-//\r
-// Register set map as specified in TIS specification Chapter 10\r
-//\r
-typedef struct {\r
- ///\r
- /// Used to gain ownership for this particular port.\r
- ///\r
- UINT8 Access; // 0\r
- UINT8 Reserved1[7]; // 1\r
- ///\r
- /// Controls interrupts.\r
- ///\r
- UINT32 IntEnable; // 8\r
- ///\r
- /// SIRQ vector to be used by the TPM.\r
- ///\r
- UINT8 IntVector; // 0ch\r
- UINT8 Reserved2[3]; // 0dh\r
- ///\r
- /// What caused interrupt.\r
- ///\r
- UINT32 IntSts; // 10h\r
- ///\r
- /// Shows which interrupts are supported by that particular TPM.\r
- ///\r
- UINT32 IntfCapability; // 14h\r
- ///\r
- /// Status Register. Provides status of the TPM.\r
- ///\r
- UINT8 Status; // 18h\r
- ///\r
- /// Number of consecutive writes that can be done to the TPM.\r
- ///\r
- UINT16 BurstCount; // 19h\r
- ///\r
- /// TPM2 support CANCEL at BIT[24] of STATUS register (WO)\r
- ///\r
- UINT8 StatusEx; // 1Bh\r
- UINT8 Reserved3[8];\r
- ///\r
- /// Read or write FIFO, depending on transaction.\r
- ///\r
- UINT32 DataFifo; // 24h\r
- UINT8 Reserved4[0xed8]; // 28h\r
- ///\r
- /// Vendor ID\r
- ///\r
- UINT16 Vid; // 0f00h\r
- ///\r
- /// Device ID\r
- ///\r
- UINT16 Did; // 0f02h\r
- ///\r
- /// Revision ID\r
- ///\r
- UINT8 Rid; // 0f04h\r
- ///\r
- /// TCG defined configuration registers.\r
- ///\r
- UINT8 TcgDefined[0x7b]; // 0f05h\r
- ///\r
- /// Alias to I/O legacy space.\r
- ///\r
- UINT32 LegacyAddress1; // 0f80h\r
- ///\r
- /// Additional 8 bits for I/O legacy space extension.\r
- ///\r
- UINT32 LegacyAddress1Ex; // 0f84h\r
- ///\r
- /// Alias to second I/O legacy space.\r
- ///\r
- UINT32 LegacyAddress2; // 0f88h\r
- ///\r
- /// Additional 8 bits for second I/O legacy space extension.\r
- ///\r
- UINT32 LegacyAddress2Ex; // 0f8ch\r
- ///\r
- /// Vendor-defined configuration registers.\r
- ///\r
- UINT8 VendorDefined[0x70];// 0f90h\r
-} TIS_PC_REGISTERS;\r
-\r
-//\r
-// Restore original structure alignment\r
-//\r
-#pragma pack ()\r
-\r
-//\r
-// Define pointer types used to access TIS registers on PC\r
-//\r
-typedef TIS_PC_REGISTERS *TIS_PC_REGISTERS_PTR;\r
-\r
-//\r
-// Define bits of ACCESS and STATUS registers\r
-//\r
-\r
-///\r
-/// This bit is a 1 to indicate that the other bits in this register are valid.\r
-///\r
-#define TIS_PC_VALID BIT7\r
-///\r
-/// Indicate that this locality is active.\r
-///\r
-#define TIS_PC_ACC_ACTIVE BIT5\r
-///\r
-/// Set to 1 to indicate that this locality had the TPM taken away while\r
-/// this locality had the TIS_PC_ACC_ACTIVE bit set.\r
-///\r
-#define TIS_PC_ACC_SEIZED BIT4\r
-///\r
-/// Set to 1 to indicate that TPM MUST reset the\r
-/// TIS_PC_ACC_ACTIVE bit and remove ownership for localities less than the\r
-/// locality that is writing this bit.\r
-///\r
-#define TIS_PC_ACC_SEIZE BIT3\r
-///\r
-/// When this bit is 1, another locality is requesting usage of the TPM.\r
-///\r
-#define TIS_PC_ACC_PENDIND BIT2\r
-///\r
-/// Set to 1 to indicate that this locality is requesting to use TPM.\r
-///\r
-#define TIS_PC_ACC_RQUUSE BIT1\r
-///\r
-/// A value of 1 indicates that a T/OS has not been established on the platform\r
-///\r
-#define TIS_PC_ACC_ESTABLISH BIT0\r
-\r
-///\r
-/// When this bit is 1, TPM is in the Ready state, \r
-/// indicating it is ready to receive a new command.\r
-///\r
-#define TIS_PC_STS_READY BIT6\r
-///\r
-/// Write a 1 to this bit to cause the TPM to execute that command.\r
-///\r
-#define TIS_PC_STS_GO BIT5\r
-///\r
-/// This bit indicates that the TPM has data available as a response.\r
-///\r
-#define TIS_PC_STS_DATA BIT4\r
-///\r
-/// The TPM sets this bit to a value of 1 when it expects another byte of data for a command.\r
-///\r
-#define TIS_PC_STS_EXPECT BIT3\r
-///\r
-/// Writes a 1 to this bit to force the TPM to re-send the response.\r
-///\r
-#define TIS_PC_STS_RETRY BIT1\r
-\r
-//\r
-// Default TimeOut value\r
-//\r
-#define TIS_TIMEOUT_A (1000 * 1000) // 1s\r
-#define TIS_TIMEOUT_B (2000 * 1000) // 2s\r
-#define TIS_TIMEOUT_C (1000 * 1000) // 1s\r
-#define TIS_TIMEOUT_D (1000 * 1000) // 1s\r
+#include <IndustryStandard/TpmTis.h>\r
\r
#define TIS_TIMEOUT_MAX (90000 * 1000) // 90s\r
\r
@retval EFI_TIMEOUT The register can't run into the expected status in time.\r
**/\r
EFI_STATUS\r
-EFIAPI\r
TisPcWaitRegisterBits (\r
IN UINT8 *Register,\r
IN UINT8 BitSet,\r
@retval EFI_TIMEOUT BurstCount can't be got in time.\r
**/\r
EFI_STATUS\r
-EFIAPI\r
TisPcReadBurstCount (\r
IN TIS_PC_REGISTERS_PTR TisReg,\r
OUT UINT16 *BurstCount\r
@retval EFI_TIMEOUT TPM chip can't be set to ready state in time.\r
**/\r
EFI_STATUS\r
-EFIAPI\r
TisPcPrepareCommand (\r
IN TIS_PC_REGISTERS_PTR TisReg\r
)\r
@retval EFI_TIMEOUT Can't get the TPM control in time.\r
**/\r
EFI_STATUS\r
-EFIAPI\r
TisPcRequestUseTpm (\r
IN TIS_PC_REGISTERS_PTR TisReg\r
)\r
@param[in, out] SizeOut Size of response data. \r
\r
@retval EFI_SUCCESS Operation completed successfully.\r
- @retval EFI_TIMEOUT The register can't run into the expected status in time.\r
@retval EFI_BUFFER_TOO_SMALL Response data buffer is too small.\r
@retval EFI_DEVICE_ERROR Unexpected device behavior.\r
@retval EFI_UNSUPPORTED Unsupported TPM version\r
\r
**/\r
EFI_STATUS\r
-TisTpmCommand (\r
+Tpm2TisTpmCommand (\r
IN TIS_PC_REGISTERS_PTR TisReg,\r
IN UINT8 *BufferIn,\r
IN UINT32 SizeIn,\r
DEBUG_CODE (\r
UINTN DebugSize;\r
\r
- DEBUG ((EFI_D_INFO, "TisTpmCommand Send - "));\r
+ DEBUG ((EFI_D_VERBOSE, "Tpm2TisTpmCommand Send - "));\r
if (SizeIn > 0x100) {\r
DebugSize = 0x40;\r
} else {\r
DebugSize = SizeIn;\r
}\r
for (Index = 0; Index < DebugSize; Index++) {\r
- DEBUG ((EFI_D_INFO, "%02x ", BufferIn[Index]));\r
+ DEBUG ((EFI_D_VERBOSE, "%02x ", BufferIn[Index]));\r
}\r
if (DebugSize != SizeIn) {\r
- DEBUG ((EFI_D_INFO, "...... "));\r
+ DEBUG ((EFI_D_VERBOSE, "...... "));\r
for (Index = SizeIn - 0x20; Index < SizeIn; Index++) {\r
- DEBUG ((EFI_D_INFO, "%02x ", BufferIn[Index]));\r
+ DEBUG ((EFI_D_VERBOSE, "%02x ", BufferIn[Index]));\r
}\r
}\r
- DEBUG ((EFI_D_INFO, "\n"));\r
+ DEBUG ((EFI_D_VERBOSE, "\n"));\r
);\r
TpmOutSize = 0;\r
\r
Status = TisPcPrepareCommand (TisReg);\r
if (EFI_ERROR (Status)){\r
- DEBUG ((DEBUG_ERROR, "Tpm is not ready for command!\n"));\r
- return Status;\r
+ DEBUG ((DEBUG_ERROR, "Tpm2 is not ready for command!\n"));\r
+ return EFI_DEVICE_ERROR;\r
}\r
//\r
// Send the command data to Tpm\r
while (Index < SizeIn) {\r
Status = TisPcReadBurstCount (TisReg, &BurstCount);\r
if (EFI_ERROR (Status)) {\r
- Status = EFI_TIMEOUT;\r
+ Status = EFI_DEVICE_ERROR;\r
goto Exit;\r
}\r
for (; BurstCount > 0 && Index < SizeIn; BurstCount--) {\r
TIS_TIMEOUT_C\r
);\r
if (EFI_ERROR (Status)) {\r
- DEBUG ((DEBUG_ERROR, "The send buffer too small!\n"));\r
+ DEBUG ((DEBUG_ERROR, "Tpm2 The send buffer too small!\n"));\r
Status = EFI_BUFFER_TOO_SMALL;\r
goto Exit;\r
}\r
TIS_TIMEOUT_MAX\r
);\r
if (EFI_ERROR (Status)) {\r
- DEBUG ((DEBUG_ERROR, "Wait for Tpm response data time out!!\n"));\r
- Status = EFI_TIMEOUT;\r
+ DEBUG ((DEBUG_ERROR, "Wait for Tpm2 response data time out!!\n"));\r
+ Status = EFI_DEVICE_ERROR;\r
goto Exit;\r
}\r
//\r
while (Index < sizeof (TPM2_RESPONSE_HEADER)) {\r
Status = TisPcReadBurstCount (TisReg, &BurstCount);\r
if (EFI_ERROR (Status)) {\r
- Status = EFI_TIMEOUT;\r
+ Status = EFI_DEVICE_ERROR;\r
goto Exit;\r
}\r
for (; BurstCount > 0; BurstCount--) {\r
}\r
}\r
DEBUG_CODE (\r
- DEBUG ((EFI_D_INFO, "TisTpmCommand ReceiveHeader - "));\r
+ DEBUG ((EFI_D_VERBOSE, "Tpm2TisTpmCommand ReceiveHeader - "));\r
for (Index = 0; Index < sizeof (TPM2_RESPONSE_HEADER); Index++) {\r
- DEBUG ((EFI_D_INFO, "%02x ", BufferOut[Index]));\r
+ DEBUG ((EFI_D_VERBOSE, "%02x ", BufferOut[Index]));\r
}\r
- DEBUG ((EFI_D_INFO, "\n"));\r
+ DEBUG ((EFI_D_VERBOSE, "\n"));\r
);\r
//\r
// Check the reponse data header (tag,parasize and returncode )\r
CopyMem (&Data16, BufferOut, sizeof (UINT16));\r
// TPM2 should not use this RSP_COMMAND\r
if (SwapBytes16 (Data16) == TPM_ST_RSP_COMMAND) {\r
- DEBUG ((EFI_D_ERROR, "TPM_ST_RSP error - %x\n", TPM_ST_RSP_COMMAND));\r
+ DEBUG ((EFI_D_ERROR, "TPM2: TPM_ST_RSP error - %x\n", TPM_ST_RSP_COMMAND));\r
Status = EFI_UNSUPPORTED;\r
goto Exit;\r
}\r
}\r
Status = TisPcReadBurstCount (TisReg, &BurstCount);\r
if (EFI_ERROR (Status)) {\r
- Status = EFI_TIMEOUT;\r
+ Status = EFI_DEVICE_ERROR;\r
goto Exit;\r
}\r
}\r
Exit:\r
DEBUG_CODE (\r
- DEBUG ((EFI_D_INFO, "TisTpmCommand Receive - "));\r
+ DEBUG ((EFI_D_VERBOSE, "Tpm2TisTpmCommand Receive - "));\r
for (Index = 0; Index < TpmOutSize; Index++) {\r
- DEBUG ((EFI_D_INFO, "%02x ", BufferOut[Index]));\r
+ DEBUG ((EFI_D_VERBOSE, "%02x ", BufferOut[Index]));\r
}\r
- DEBUG ((EFI_D_INFO, "\n"));\r
+ DEBUG ((EFI_D_VERBOSE, "\n"));\r
);\r
MmioWrite8((UINTN)&TisReg->Status, TIS_PC_STS_READY);\r
return Status;\r
**/\r
EFI_STATUS\r
EFIAPI\r
-DTpm2SubmitCommand (\r
+DTpm2TisSubmitCommand (\r
IN UINT32 InputParameterBlockSize,\r
IN UINT8 *InputParameterBlock,\r
IN OUT UINT32 *OutputParameterBlockSize,\r
IN UINT8 *OutputParameterBlock\r
)\r
{\r
- return TisTpmCommand (\r
+ return Tpm2TisTpmCommand (\r
(TIS_PC_REGISTERS_PTR) (UINTN) PcdGet64 (PcdTpmBaseAddress),\r
InputParameterBlock,\r
InputParameterBlockSize,\r
**/\r
EFI_STATUS\r
EFIAPI\r
-DTpm2RequestUseTpm (\r
+DTpm2TisRequestUseTpm (\r
VOID\r
)\r
{\r
projects / mirror_edk2.git / blobdiff