X-Git-Url: https://git.proxmox.com/?p=mirror_edk2.git;a=blobdiff_plain;f=EmbeddedPkg%2FUniversal%2FMmcDxe%2FMmc.h;h=a77ba41575f101cd156a2f3fb58e1a71910b26fc;hp=46a156cecf88ab2999237728d8c7386d20ff039f;hb=76c09700edc67686b29662e81a3ca7d947594ce5;hpb=eff98cf9daf7353274f958bea570f0da419a09a5 diff --git a/EmbeddedPkg/Universal/MmcDxe/Mmc.h b/EmbeddedPkg/Universal/MmcDxe/Mmc.h index 46a156cecf..a77ba41575 100644 --- a/EmbeddedPkg/Universal/MmcDxe/Mmc.h +++ b/EmbeddedPkg/Universal/MmcDxe/Mmc.h @@ -34,6 +34,10 @@ #define MMC_OCR_POWERUP 0x80000000 +#define MMC_OCR_ACCESS_MASK 0x3 /* bit[30-29] */ +#define MMC_OCR_ACCESS_BYTE 0x1 /* bit[29] */ +#define MMC_OCR_ACCESS_SECTOR 0x2 /* bit[30] */ + #define MMC_CSD_GET_CCC(Response) (Response[2] >> 20) #define MMC_CSD_GET_TRANSPEED(Response) (Response[3] & 0xFF) #define MMC_CSD_GET_READBLLEN(Response) ((Response[2] >> 16) & 0xF) @@ -55,6 +59,19 @@ #define MMC_R0_STATE_TRAN 4 #define MMC_R0_STATE_DATA 5 +#define EMMC_CMD6_ARG_ACCESS(x) (((x) & 0x3) << 24) +#define EMMC_CMD6_ARG_INDEX(x) (((x) & 0xFF) << 16) +#define EMMC_CMD6_ARG_VALUE(x) (((x) & 0xFF) << 8) +#define EMMC_CMD6_ARG_CMD_SET(x) (((x) & 0x7) << 0) + +#define SWITCH_CMD_DATA_LENGTH 64 +#define SD_HIGH_SPEED_SUPPORTED 0x20000 +#define SD_DEFAULT_SPEED 25000000 +#define SD_HIGH_SPEED 50000000 +#define SWITCH_CMD_SUCCESS_MASK 0x0f000000 + +#define BUSWIDTH_4 4 + typedef enum { UNKNOWN_CARD, MMC_CARD, //MMC card @@ -75,6 +92,22 @@ typedef struct { UINT32 PowerUp: 1; // This bit is set to LOW if the card has not finished the power up routine } OCR; +typedef struct { + UINT8 SD_SPEC: 4; // SD Memory Card - Spec. Version [59:56] + UINT8 SCR_STRUCTURE: 4; // SCR Structure [63:60] + UINT8 SD_BUS_WIDTHS: 4; // DAT Bus widths supported [51:48] + UINT8 DATA_STAT_AFTER_ERASE: 1; // Data Status after erases [55] + UINT8 SD_SECURITY: 3; // CPRM Security Support [54:52] + UINT8 EX_SECURITY_1: 1; // Extended Security Support [43] + UINT8 SD_SPEC4: 1; // Spec. Version 4.00 or higher [42] + UINT8 RESERVED_1: 2; // Reserved [41:40] + UINT8 SD_SPEC3: 1; // Spec. Version 3.00 or higher [47] + UINT8 EX_SECURITY_2: 3; // Extended Security Support [46:44] + UINT8 CMD_SUPPORT: 4; // Command Support bits [35:32] + UINT8 RESERVED_2: 4; // Reserved [39:36] + UINT32 RESERVED_3; // Manufacturer Usage [31:0] +} SCR; + typedef struct { UINT32 NOT_USED; // 1 [0:0] UINT32 CRC; // CRC7 checksum [7:1] @@ -128,16 +161,173 @@ typedef struct { UINT8 NSAC ; // Data read access-time 2 in CLK cycles (NSAC*100) [111:104] UINT8 TAAC ; // Data read access-time 1 [119:112] - UINT8 RESERVED_5: 6; // Reserved [125:120] + UINT8 RESERVED_5: 2; // Reserved [121:120] + UINT8 SPEC_VERS: 4; // System specification version [125:122] UINT8 CSD_STRUCTURE: 2; // CSD structure [127:126] } CSD; +typedef struct { + UINT8 RESERVED_1[16]; // Reserved [15:0] + UINT8 SECURE_REMOVAL_TYPE; // Secure Removal Type [16:16] + UINT8 PRODUCT_STATE_AWARENESS_ENABLEMENT; // Product state awareness enablement [17:17] + UINT8 MAX_PRE_LOADING_DATA_SIZE[4]; // MAX pre loading data size [21:18] + UINT8 PRE_LOADING_DATA_SIZE[4]; // Pre loading data size [25:22] + UINT8 FFU_STATUS; // FFU Status [26:26] + UINT8 RESERVED_2[2]; // Reserved [28:27] + UINT8 MODE_OPERATION_CODES; // Mode operation codes [29:29] + UINT8 MODE_CONFIG; // Mode config [30:30] + UINT8 RESERVED_3; // Reserved [31:31] + UINT8 FLUSH_CACHE; // Flushing of the cache [32:32] + UINT8 CACHE_CTRL; // Control to turn the cache ON/OFF [33:33] + UINT8 POWER_OFF_NOTIFICATION; // Power Off Notification [34:34] + UINT8 PACKED_FAILURE_INDEX; // Packed command failure index [35:35] + UINT8 PACKED_COMMAND_STATUS; // Packed command status [36:36] + UINT8 CONTEXT_CONF[15]; // Context configuration [51:37] + UINT8 EXT_PARTITIONS_ATTRIBUTE[2]; // Extended partitions attribute [53:52] + UINT8 EXCEPTION_EVENTS_STATUS[2]; // Exception events status [55:54] + UINT8 EXCEPTION_EVENTS_CTRL[2]; // Exception events control [57:56] + UINT8 DYNCAP_NEEDED; // Number of addressed group to be released [58:58] + UINT8 CLASS_6_CTRL; // Class 6 commands control [59:59] + UINT8 INI_TIMEOUT_EMU; // 1st initialization after disabling sector size emulation [60:60] + UINT8 DATA_SECTOR_SIZE; // Sector size [61:61] + UINT8 USE_NATIVE_SECTOR; // Sector size emulation [62:62] + UINT8 NATIVE_SECTOR_SIZE; // Native sector size [63:63] + UINT8 VENDOR_SPECIFIC_FIELD[64]; // Vendor specific fields [127:64] + UINT8 RESERVED_4[2]; // Reserved [129:128] + UINT8 PROGRAM_CID_CSD_DDR_SUPPORT; // Program CID/CSD in DDR mode support [130:130] + UINT8 PERIODIC_WAKEUP; // Periodic wake-up [131:131] + UINT8 TCASE_SUPPORT; // Package case temperature is controlled [132:132] + UINT8 PRODUCTION_STATE_AWARENESS; // Production state awareness [133:133] + UINT8 SECTOR_BAD_BLK_MGMNT; // Bad block management mode [134:134] + UINT8 RESERVED_5; // Reserved [135:135] + UINT8 ENH_START_ADDR[4]; // Enhanced user data start address [139:136] + UINT8 ENH_SIZE_MULT[3]; // Enhanced user data area size [142:140] + UINT8 GP_SIZE_MULT[12]; // General purpose partition size [154:143] + UINT8 PARTITION_SETTING_COMPLETED; // Partitioning setting [155:155] + UINT8 PARTITIONS_ATTRIBUTE; // Partitions attribute [156:156] + UINT8 MAX_ENH_SIZE_MULT[3]; // Max enhanced area size [159:157] + UINT8 PARTITIONING_SUPPORT; // Partitioning [160:160] + UINT8 HPI_MGMT; // HPI management [161:161] + UINT8 RST_N_FUNCTION; // H/W reset function [162:162] + UINT8 BKOPS_EN; // Enable background operations handshake [163:163] + UINT8 BKOPS_START; // Manually start background operations [164:164] + UINT8 SANITIZE_START; // Start sanitize operation [165:165] + UINT8 WR_REL_PARAM; // Write reliability parameter register [166:166] + UINT8 WR_REL_SET; // Write reliability setting register [167:167] + UINT8 RPMB_SIZE_MULT; // RPMB size [168:168] + UINT8 FW_CONFIG; // FW configuration [169:169] + UINT8 RESERVED_6; // Reserved [170:170] + UINT8 USER_WP; // User area write protection register [171:171] + UINT8 RESERVED_7; // Reserved [172:172] + UINT8 BOOT_WP; // Boot area write protection register [173:173] + UINT8 BOOT_WP_STATUS; // Boot write protection register [174:174] + UINT8 ERASE_GROUP_DEF; // High-density erase group definition [175:175] + UINT8 RESERVED_8; // Reserved [176:176] + UINT8 BOOT_BUS_CONDITIONS; // Boot bus conditions [177:177] + UINT8 BOOT_CONFIG_PROT; // Boot config protection [178:178] + UINT8 PARTITION_CONFIG; // Partition config [179:179] + UINT8 RESERVED_9; // Reserved [180:180] + UINT8 ERASED_MEM_CONT; // Erased memory content [181:181] + UINT8 RESERVED_10; // Reserved [182:182] + UINT8 BUS_WIDTH; // Bus width mode [183:183] + UINT8 RESERVED_11; // Reserved [184:184] + UINT8 HS_TIMING; // High-speed interface timing [185:185] + UINT8 RESERVED_12; // Reserved [186:186] + UINT8 POWER_CLASS; // Power class [187:187] + UINT8 RESERVED_13; // Reserved [188:188] + UINT8 CMD_SET_REV; // Command set revision [189:189] + UINT8 RESERVED_14; // Reserved [190:190] + UINT8 CMD_SET; // Command set [191:191] + UINT8 EXT_CSD_REV; // Extended CSD revision [192:192] + UINT8 RESERVED_15; // Reserved [193:193] + UINT8 CSD_STRUCTURE; // CSD Structure [194:194] + UINT8 RESERVED_16; // Reserved [195:195] + UINT8 DEVICE_TYPE; // Device type [196:196] + UINT8 DRIVER_STRENGTH; // I/O Driver strength [197:197] + UINT8 OUT_OF_INTERRUPT_TIME; // Out-of-interrupt busy timing [198:198] + UINT8 PARTITION_SWITCH_TIME; // Partition switching timing [199:199] + UINT8 PWR_CL_52_195; // Power class for 52MHz at 1.95V 1 R [200:200] + UINT8 PWR_CL_26_195; // Power class for 26MHz at 1.95V 1 R [201:201] + UINT8 PWR_CL_52_360; // Power class for 52MHz at 3.6V 1 R [202:202] + UINT8 PWR_CL_26_360; // Power class for 26MHz at 3.6V 1 R [203:203] + UINT8 RESERVED_17; // Reserved [204:204] + UINT8 MIN_PERF_R_4_26; // Minimum read performance for 4bit at 26MHz [205:205] + UINT8 MIN_PERF_W_4_26; // Minimum write performance for 4bit at 26MHz [206:206] + UINT8 MIN_PERF_R_8_26_4_52; // Minimum read performance for 8bit at 26MHz, for 4bit at 52MHz [207:207] + UINT8 MIN_PERF_W_8_26_4_52; // Minimum write performance for 8bit at 26MHz, for 4bit at 52MHz [208:208] + UINT8 MIN_PERF_R_8_52; // Minimum read performance for 8bit at 52MHz [209:209] + UINT8 MIN_PERF_W_8_52; // Minimum write performance for 8bit at 52MHz [210:210] + UINT8 RESERVED_18; // Reserved [211:211] + UINT32 SECTOR_COUNT; // Sector count [215:212] + UINT8 SLEEP_NOTIFICATION_TIME; // Sleep notification timout [216:216] + UINT8 S_A_TIMEOUT; // Sleep/awake timeout [217:217] + UINT8 PRODUCTION_STATE_AWARENESS_TIMEOUT; // Production state awareness timeout [218:218] + UINT8 S_C_VCCQ; // Sleep current (VCCQ) [219:219] + UINT8 S_C_VCC; // Sleep current (VCC) [220:220] + UINT8 HC_WP_GRP_SIZE; // High-capacity write protect group size [221:221] + UINT8 REL_WR_SECTOR_C; // Reliable write sector count [222:222] + UINT8 ERASE_TIMEOUT_MULT; // High-capacity erase timeout [223:223] + UINT8 HC_ERASE_GRP_SIZE; // High-capacity erase unit size [224:224] + UINT8 ACC_SIZE; // Access size [225:225] + UINT8 BOOT_SIZE_MULTI; // Boot partition size [226:226] + UINT8 RESERVED_19; // Reserved [227:227] + UINT8 BOOT_INFO; // Boot information [228:228] + UINT8 SECURE_TRIM_MULT; // Secure TRIM Multiplier [229:229] + UINT8 SECURE_ERASE_MULT; // Secure Erase Multiplier [230:230] + UINT8 SECURE_FEATURE_SUPPORT; // Secure Feature Support [231:231] + UINT8 TRIM_MULT; // TRIM Multiplier [232:232] + UINT8 RESERVED_20; // Reserved [233:233] + UINT8 MIN_PREF_DDR_R_8_52; // Minimum read performance for 8bit at 52MHz in DDR mode [234:234] + UINT8 MIN_PREF_DDR_W_8_52; // Minimum write performance for 8bit at 52MHz in DDR mode [235:235] + UINT8 PWR_CL_200_130; // Power class for 200MHz at VCCQ=1.3V, VCC=3.6V [236:236] + UINT8 PWR_CL_200_195; // Power class for 200MHz at VCCQ=1.95V, VCC=3.6V [237:237] + UINT8 PWR_CL_DDR_52_195; // Power class for 52MHz, DDR at 1.95V [238:238] + UINT8 PWR_CL_DDR_52_360; // Power class for 52Mhz, DDR at 3.6V [239:239] + UINT8 RESERVED_21; // Reserved [240:240] + UINT8 INI_TIMEOUT_AP; // 1st initialization time after partitioning [241:241] + UINT8 CORRECTLY_PRG_SECTORS_NUM[4]; // Number of correctly programmed sectors [245:242] + UINT8 BKOPS_STATUS; // Background operations status [246:246] + UINT8 POWER_OFF_LONG_TIME; // Power off notification (long) timeout [247:247] + UINT8 GENERIC_CMD6_TIME; // Generic CMD6 timeout [248:248] + UINT8 CACHE_SIZE[4]; // Cache size [252:249] + UINT8 PWR_CL_DDR_200_360; // Power class for 200MHz, DDR at VCC=3.6V [253:253] + UINT8 FIRMWARE_VERSION[8]; // Firmware version [261:254] + UINT8 DEVICE_VERSION[2]; // Device version [263:262] + UINT8 OPTIMAL_TRIM_UNIT_SIZE; // Optimal trim unit size [264:264] + UINT8 OPTIMAL_WRITE_SIZE; // Optimal write size [265:265] + UINT8 OPTIMAL_READ_SIZE; // Optimal read size [266:266] + UINT8 PRE_EOL_INFO; // Pre EOL information [267:267] + UINT8 DEVICE_LIFE_TIME_EST_TYP_A; // Device life time estimation type A [268:268] + UINT8 DEVICE_LIFE_TIME_EST_TYP_B; // Device life time estimation type B [269:269] + UINT8 VENDOR_PROPRIETARY_HEALTH_REPORT[32]; // Vendor proprietary health report [301:270] + UINT8 NUMBER_OF_FW_SECTORS_CORRECTLY_PROGRAMMED[4]; // Number of FW sectors correctly programmed [305:302] + UINT8 RESERVED_22[181]; // Reserved [486:306] + UINT8 FFU_ARG[4]; // FFU argument [490:487] + UINT8 OPERATION_CODE_TIMEOUT; // Operation codes timeout [491:491] + UINT8 FFU_FEATURES; // FFU features [492:492] + UINT8 SUPPORTED_MODES; // Supported modes [493:493] + UINT8 EXT_SUPPORT; // Extended partitions attribute support [494:494] + UINT8 LARGE_UNIT_SIZE_M1; // Large unit size [495:495] + UINT8 CONTEXT_CAPABILITIES; // Context management capabilities [496:496] + UINT8 TAG_RES_SIZE; // Tag resource size [497:497] + UINT8 TAG_UNIT_SIZE; // Tag unit size [498:498] + UINT8 DATA_TAG_SUPPORT; // Data tag support [499:499] + UINT8 MAX_PACKED_WRITES; // Max packed write commands [500:500] + UINT8 MAX_PACKED_READS; // Max packed read commands [501:501] + UINT8 BKOPS_SUPPORT; // Background operations support [502:502] + UINT8 HPI_FEATURES; // HPI features [503:503] + UINT8 S_CMD_SET; // Supported command sets [504:504] + UINT8 EXT_SECURITY_ERR; // Extended security commands error [505:505] + UINT8 RESERVED_23[6]; // Reserved [511:506] +} ECSD; + typedef struct { UINT16 RCA; CARD_TYPE CardType; OCR OCRData; CID CIDData; CSD CSDData; + ECSD *ECSDData; // MMC V4 extended card specific } CARD_INFO; typedef struct _MMC_HOST_INSTANCE {