X-Git-Url: https://git.proxmox.com/?p=mirror_edk2.git;a=blobdiff_plain;f=PcAtChipsetPkg%2FLibrary%2FSerialIoLib%2FSerialPortLib.c;h=95e0db70ad6915872a1b2c8050ad5044b5dc06e6;hp=6bf705312d88fd6f9624f954053575e1f7b21e3f;hb=bbbc509fe5df6b22eb6dbe26ae7a536aa5d0ff02;hpb=24115e44926b33c763f81026690f20efd913daf2
diff --git a/PcAtChipsetPkg/Library/SerialIoLib/SerialPortLib.c b/PcAtChipsetPkg/Library/SerialIoLib/SerialPortLib.c
index 6bf705312d..95e0db70ad 100644
--- a/PcAtChipsetPkg/Library/SerialIoLib/SerialPortLib.c
+++ b/PcAtChipsetPkg/Library/SerialIoLib/SerialPortLib.c
@@ -1,7 +1,7 @@
/** @file
UART Serial Port library functions
- Copyright (c) 2006 - 2009, Intel Corporation. All rights reserved.
+ Copyright (c) 2006 - 2017, Intel Corporation. All rights reserved.
This program and the accompanying materials
are licensed and made available under the terms and conditions of the BSD License
which accompanies this distribution. The full text of the license may be found at
@@ -39,6 +39,12 @@
#define LSR_TXRDY 0x20
#define LSR_RXDA 0x01
#define DLAB 0x01
+#define MCR_DTRC 0x01
+#define MCR_RTS 0x02
+#define MSR_CTS 0x10
+#define MSR_DSR 0x20
+#define MSR_RI 0x40
+#define MSR_DCD 0x80
//---------------------------------------------
// UART Settings
@@ -54,7 +60,7 @@ UINT8 gBreakSet = 0;
Initialize the serial device hardware.
If no initialization is required, then return RETURN_SUCCESS.
- If the serial device was successfuly initialized, then return RETURN_SUCCESS.
+ If the serial device was successfully initialized, then return RETURN_SUCCESS.
If the serial device could not be initialized, then return RETURN_DEVICE_ERROR.
@retval RETURN_SUCCESS The serial device was initialized.
@@ -85,19 +91,19 @@ SerialPortInitialize (
// Set communications format
//
OutputData = (UINT8) ((DLAB << 7) | (gBreakSet << 6) | (gParity << 3) | (gStop << 2) | Data);
- IoWrite8 ((UINTN) (gUartBase + LCR_OFFSET), OutputData);
+ IoWrite8 (gUartBase + LCR_OFFSET, OutputData);
//
// Configure baud rate
//
- IoWrite8 ((UINTN) (gUartBase + BAUD_HIGH_OFFSET), (UINT8) (Divisor >> 8));
- IoWrite8 ((UINTN) (gUartBase + BAUD_LOW_OFFSET), (UINT8) (Divisor & 0xff));
+ IoWrite8 (gUartBase + BAUD_HIGH_OFFSET, (UINT8) (Divisor >> 8));
+ IoWrite8 (gUartBase + BAUD_LOW_OFFSET, (UINT8) (Divisor & 0xff));
//
// Switch back to bank 0
//
OutputData = (UINT8) ((~DLAB << 7) | (gBreakSet << 6) | (gParity << 3) | (gStop << 2) | Data);
- IoWrite8 ((UINTN) (gUartBase + LCR_OFFSET), OutputData);
+ IoWrite8 (gUartBase + LCR_OFFSET, OutputData);
return RETURN_SUCCESS;
}
@@ -118,7 +124,7 @@ SerialPortInitialize (
@retval 0 NumberOfBytes is 0.
@retval >0 The number of bytes written to the serial device.
- If this value is less than NumberOfBytes, then the read operation failed.
+ If this value is less than NumberOfBytes, then the write operation failed.
**/
UINTN
@@ -219,3 +225,265 @@ SerialPortPoll (
return (BOOLEAN) ((Data & LSR_RXDA) != 0);
}
+/**
+ Sets the control bits on a serial device.
+
+ @param Control Sets the bits of Control that are settable.
+
+ @retval RETURN_SUCCESS The new control bits were set on the serial device.
+ @retval RETURN_UNSUPPORTED The serial device does not support this operation.
+ @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
+
+**/
+RETURN_STATUS
+EFIAPI
+SerialPortSetControl (
+ IN UINT32 Control
+ )
+{
+ UINT8 Mcr;
+
+ //
+ // First determine the parameter is invalid.
+ //
+ if ((Control & (~(EFI_SERIAL_REQUEST_TO_SEND | EFI_SERIAL_DATA_TERMINAL_READY))) != 0) {
+ return RETURN_UNSUPPORTED;
+ }
+
+ //
+ // Read the Modem Control Register.
+ //
+ Mcr = IoRead8 ((UINT16) gUartBase + MCR_OFFSET);
+ Mcr &= (~(MCR_DTRC | MCR_RTS));
+
+ if ((Control & EFI_SERIAL_DATA_TERMINAL_READY) == EFI_SERIAL_DATA_TERMINAL_READY) {
+ Mcr |= MCR_DTRC;
+ }
+
+ if ((Control & EFI_SERIAL_REQUEST_TO_SEND) == EFI_SERIAL_REQUEST_TO_SEND) {
+ Mcr |= MCR_RTS;
+ }
+
+ //
+ // Write the Modem Control Register.
+ //
+ IoWrite8 ((UINT16) gUartBase + MCR_OFFSET, Mcr);
+
+ return RETURN_SUCCESS;
+}
+
+/**
+ Retrieve the status of the control bits on a serial device.
+
+ @param Control A pointer to return the current control signals from the serial device.
+
+ @retval RETURN_SUCCESS The control bits were read from the serial device.
+ @retval RETURN_UNSUPPORTED The serial device does not support this operation.
+ @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
+
+**/
+RETURN_STATUS
+EFIAPI
+SerialPortGetControl (
+ OUT UINT32 *Control
+ )
+{
+ UINT8 Msr;
+ UINT8 Mcr;
+ UINT8 Lsr;
+
+ *Control = 0;
+
+ //
+ // Read the Modem Status Register.
+ //
+ Msr = IoRead8 ((UINT16) gUartBase + MSR_OFFSET);
+
+ if ((Msr & MSR_CTS) == MSR_CTS) {
+ *Control |= EFI_SERIAL_CLEAR_TO_SEND;
+ }
+
+ if ((Msr & MSR_DSR) == MSR_DSR) {
+ *Control |= EFI_SERIAL_DATA_SET_READY;
+ }
+
+ if ((Msr & MSR_RI) == MSR_RI) {
+ *Control |= EFI_SERIAL_RING_INDICATE;
+ }
+
+ if ((Msr & MSR_DCD) == MSR_DCD) {
+ *Control |= EFI_SERIAL_CARRIER_DETECT;
+ }
+
+ //
+ // Read the Modem Control Register.
+ //
+ Mcr = IoRead8 ((UINT16) gUartBase + MCR_OFFSET);
+
+ if ((Mcr & MCR_DTRC) == MCR_DTRC) {
+ *Control |= EFI_SERIAL_DATA_TERMINAL_READY;
+ }
+
+ if ((Mcr & MCR_RTS) == MCR_RTS) {
+ *Control |= EFI_SERIAL_REQUEST_TO_SEND;
+ }
+
+ //
+ // Read the Line Status Register.
+ //
+ Lsr = IoRead8 ((UINT16) gUartBase + LSR_OFFSET);
+
+ if ((Lsr & LSR_TXRDY) == LSR_TXRDY) {
+ *Control |= EFI_SERIAL_OUTPUT_BUFFER_EMPTY;
+ }
+
+ if ((Lsr & LSR_RXDA) == 0) {
+ *Control |= EFI_SERIAL_INPUT_BUFFER_EMPTY;
+ }
+
+ return RETURN_SUCCESS;
+}
+
+/**
+ Sets the baud rate, receive FIFO depth, transmit/receice time out, parity,
+ data bits, and stop bits on a serial device.
+
+ @param BaudRate The requested baud rate. A BaudRate value of 0 will use the
+ device's default interface speed.
+ On output, the value actually set.
+ @param ReveiveFifoDepth The requested depth of the FIFO on the receive side of the
+ serial interface. A ReceiveFifoDepth value of 0 will use
+ the device's default FIFO depth.
+ On output, the value actually set.
+ @param Timeout The requested time out for a single character in microseconds.
+ This timeout applies to both the transmit and receive side of the
+ interface. A Timeout value of 0 will use the device's default time
+ out value.
+ On output, the value actually set.
+ @param Parity The type of parity to use on this serial device. A Parity value of
+ DefaultParity will use the device's default parity value.
+ On output, the value actually set.
+ @param DataBits The number of data bits to use on the serial device. A DataBits
+ vaule of 0 will use the device's default data bit setting.
+ On output, the value actually set.
+ @param StopBits The number of stop bits to use on this serial device. A StopBits
+ value of DefaultStopBits will use the device's default number of
+ stop bits.
+ On output, the value actually set.
+
+ @retval RETURN_SUCCESS The new attributes were set on the serial device.
+ @retval RETURN_UNSUPPORTED The serial device does not support this operation.
+ @retval RETURN_INVALID_PARAMETER One or more of the attributes has an unsupported value.
+ @retval RETURN_DEVICE_ERROR The serial device is not functioning correctly.
+
+**/
+RETURN_STATUS
+EFIAPI
+SerialPortSetAttributes (
+ IN OUT UINT64 *BaudRate,
+ IN OUT UINT32 *ReceiveFifoDepth,
+ IN OUT UINT32 *Timeout,
+ IN OUT EFI_PARITY_TYPE *Parity,
+ IN OUT UINT8 *DataBits,
+ IN OUT EFI_STOP_BITS_TYPE *StopBits
+ )
+{
+ UINTN Divisor;
+ UINT8 OutputData;
+ UINT8 LcrData;
+ UINT8 LcrParity;
+ UINT8 LcrStop;
+
+ //
+ // Check for default settings and fill in actual values.
+ //
+ if (*BaudRate == 0) {
+ *BaudRate = gBps;
+ }
+
+ if (*DataBits == 0) {
+ *DataBits = gData;
+ }
+
+ if (*Parity == DefaultParity) {
+ *Parity = NoParity;
+ }
+
+ if (*StopBits == DefaultStopBits) {
+ *StopBits = OneStopBit;
+ }
+
+ if ((*DataBits < 5) || (*DataBits > 8)) {
+ return RETURN_INVALID_PARAMETER;
+ }
+
+ //
+ // Map 5..8 to 0..3
+ //
+ LcrData = (UINT8) (*DataBits - (UINT8) 5);
+
+ switch (*Parity) {
+ case NoParity:
+ LcrParity = 0;
+ break;
+
+ case EvenParity:
+ LcrParity = 3;
+ break;
+
+ case OddParity:
+ LcrParity = 1;
+ break;
+
+ case SpaceParity:
+ LcrParity = 7;
+ break;
+
+ case MarkParity:
+ LcrParity = 5;
+ break;
+
+ default:
+ return RETURN_INVALID_PARAMETER;
+ }
+
+ switch (*StopBits) {
+ case OneStopBit:
+ LcrStop = 0;
+ break;
+
+ case OneFiveStopBits:
+ case TwoStopBits:
+ LcrStop = 1;
+ break;
+
+ default:
+ return RETURN_INVALID_PARAMETER;
+ }
+
+ //
+ // Calculate divisor for baud generator
+ //
+ Divisor = 115200 / (UINTN) *BaudRate;
+
+ //
+ // Set communications format
+ //
+ OutputData = (UINT8) ((DLAB << 7) | (gBreakSet << 6) | (LcrParity << 3) | (LcrStop << 2) | LcrData);
+ IoWrite8 (gUartBase + LCR_OFFSET, OutputData);
+
+ //
+ // Configure baud rate
+ //
+ IoWrite8 (gUartBase + BAUD_HIGH_OFFSET, (UINT8) (Divisor >> 8));
+ IoWrite8 (gUartBase + BAUD_LOW_OFFSET, (UINT8) (Divisor & 0xff));
+
+ //
+ // Switch back to bank 0
+ //
+ OutputData = (UINT8) ((~DLAB << 7) | (gBreakSet << 6) | (LcrParity << 3) | (LcrStop << 2) | LcrData);
+ IoWrite8 (gUartBase + LCR_OFFSET, OutputData);
+
+ return RETURN_SUCCESS;
+}
+