DEFINE SECURE_BOOT_ENABLE = FALSE\r
DEFINE SOURCE_DEBUG_ENABLE = FALSE\r
+ #
+ # Serial port set up
+ #
+ DEFINE BAUD_RATE = 115200
+ DEFINE SERIAL_CLOCK_RATE = 1843200
+ DEFINE SERIAL_LINE_CONTROL = 3 # 8-bits, no parity
+ DEFINE SERIAL_HARDWARE_FLOW_CONTROL = FALSE
+ DEFINE SERIAL_DETECT_CABLE = FALSE
+ DEFINE SERIAL_FIFO_CONTROL = 7 # Enable FIFO
+ DEFINE SERIAL_EXTENDED_TX_FIFO_SIZE = 16
+ DEFINE UART_DEFAULT_BAUD_RATE = $(BAUD_RATE)
+ DEFINE UART_DEFAULT_DATA_BITS = 8
+ DEFINE UART_DEFAULT_PARITY = 1
+ DEFINE UART_DEFAULT_STOP_BITS = 1
+ DEFINE DEFAULT_TERMINAL_TYPE = 0
+
+ #
+ # typedef struct {
+ # UINT16 VendorId; ///< Vendor ID to match the PCI device. The value 0xFFFF terminates the list of entries.
+ # UINT16 DeviceId; ///< Device ID to match the PCI device
+ # UINT32 ClockRate; ///< UART clock rate. Set to 0 for default clock rate of 1843200 Hz
+ # UINT64 Offset; ///< The byte offset into to the BAR
+ # UINT8 BarIndex; ///< Which BAR to get the UART base address
+ # UINT8 RegisterStride; ///< UART register stride in bytes. Set to 0 for default register stride of 1 byte.
+ # UINT16 ReceiveFifoDepth; ///< UART receive FIFO depth in bytes. Set to 0 for a default FIFO depth of 16 bytes.
+ # UINT16 TransmitFifoDepth; ///< UART transmit FIFO depth in bytes. Set to 0 for a default FIFO depth of 16 bytes.
+ # UINT8 Reserved[2];
+ # } PCI_SERIAL_PARAMETER;
+ #
+ # Vendor 0000 Device 0000 Prog Interface 1, BAR #0, Offset 0, Stride = 1, Clock 1843200 (0x1c2000)
+ #
+ # [Vendor] [Device] [----ClockRate---] [------------Offset-----------] [Bar] [Stride] [RxFifo] [TxFifo] [Rsvd] [Vendor]
+ DEFINE PCI_SERIAL_PARAMETERS = {0x00,0x00, 0x00,0x00, 0x0,0x20,0x1c,0x00, 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0, 0x00, 0x01, 0x0,0x0, 0x0,0x0, 0x0,0x0, 0xff,0xff}
+
#
# Shell options: [BUILD_SHELL, FULL_BIN, MIN_BIN, NONE, UEFI]
#
gEfiMdeModulePkgTokenSpaceGuid.PcdConOutUgaSupport|FALSE\r
\r
[PcdsFixedAtBuild]\r
- gEfiMdePkgTokenSpaceGuid.PcdReportStatusCodePropertyMask|0x7\r
- gEfiMdePkgTokenSpaceGuid.PcdDebugPrintErrorLevel|0x8000004F\r
-!if $(SOURCE_DEBUG_ENABLE)\r
- gEfiMdePkgTokenSpaceGuid.PcdDebugPropertyMask|0x17\r
-!else\r
- gEfiMdePkgTokenSpaceGuid.PcdDebugPropertyMask|0x2F\r
-!endif\r
gEfiMdeModulePkgTokenSpaceGuid.PcdMaxVariableSize|0x10000\r
gEfiMdeModulePkgTokenSpaceGuid.PcdMaxHardwareErrorVariableSize|0x8000\r
gEfiMdeModulePkgTokenSpaceGuid.PcdVariableStoreSize|0x10000\r
!endif\r
\r
[PcdsPatchableInModule.common]\r
+ gEfiMdePkgTokenSpaceGuid.PcdReportStatusCodePropertyMask|0x7
+ gEfiMdePkgTokenSpaceGuid.PcdDebugPrintErrorLevel|0x8000004F
+!if $(SOURCE_DEBUG_ENABLE)
+ gEfiMdePkgTokenSpaceGuid.PcdDebugPropertyMask|0x17
+!else
+ gEfiMdePkgTokenSpaceGuid.PcdDebugPropertyMask|0x2F
+!endif
+
+ #
+ # The following parameters are set by Library/PlatformHookLib
+ #
gEfiMdeModulePkgTokenSpaceGuid.PcdSerialUseMmio|FALSE\r
- gEfiMdeModulePkgTokenSpaceGuid.PcdSerialRegisterBase|0x03F8\r
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialRegisterBase|0x3f8
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialBaudRate|$(BAUD_RATE)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialRegisterStride|1
+
+ #
+ # Enable these parameters to be set on the command line
+ #
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialClockRate|$(SERIAL_CLOCK_RATE)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialLineControl|$(SERIAL_LINE_CONTROL)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialUseHardwareFlowControl|$(SERIAL_HARDWARE_FLOW_CONTROL)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialDetectCable|$(SERIAL_DETECT_CABLE)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialFifoControl|$(SERIAL_FIFO_CONTROL)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialExtendedTxFifoSize|$(SERIAL_EXTENDED_TX_FIFO_SIZE)
+
+ gEfiMdePkgTokenSpaceGuid.PcdUartDefaultBaudRate|$(UART_DEFAULT_BAUD_RATE)
+ gEfiMdePkgTokenSpaceGuid.PcdUartDefaultDataBits|$(UART_DEFAULT_DATA_BITS)
+ gEfiMdePkgTokenSpaceGuid.PcdUartDefaultParity|$(UART_DEFAULT_PARITY)
+ gEfiMdePkgTokenSpaceGuid.PcdUartDefaultStopBits|$(UART_DEFAULT_STOP_BITS)
+ gEfiMdePkgTokenSpaceGuid.PcdDefaultTerminalType|$(DEFAULT_TERMINAL_TYPE)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdPciSerialParameters|$(PCI_SERIAL_PARAMETERS)
\r
################################################################################\r
#\r
DEFINE SECURE_BOOT_ENABLE = FALSE\r
DEFINE SOURCE_DEBUG_ENABLE = FALSE\r
+ #
+ # Serial port set up
+ #
+ DEFINE BAUD_RATE = 115200
+ DEFINE SERIAL_CLOCK_RATE = 1843200
+ DEFINE SERIAL_LINE_CONTROL = 3 # 8-bits, no parity
+ DEFINE SERIAL_HARDWARE_FLOW_CONTROL = FALSE
+ DEFINE SERIAL_DETECT_CABLE = FALSE
+ DEFINE SERIAL_FIFO_CONTROL = 7 # Enable FIFO
+ DEFINE SERIAL_EXTENDED_TX_FIFO_SIZE = 16
+ DEFINE UART_DEFAULT_BAUD_RATE = $(BAUD_RATE)
+ DEFINE UART_DEFAULT_DATA_BITS = 8
+ DEFINE UART_DEFAULT_PARITY = 1
+ DEFINE UART_DEFAULT_STOP_BITS = 1
+ DEFINE DEFAULT_TERMINAL_TYPE = 0
+
+ #
+ # typedef struct {
+ # UINT16 VendorId; ///< Vendor ID to match the PCI device. The value 0xFFFF terminates the list of entries.
+ # UINT16 DeviceId; ///< Device ID to match the PCI device
+ # UINT32 ClockRate; ///< UART clock rate. Set to 0 for default clock rate of 1843200 Hz
+ # UINT64 Offset; ///< The byte offset into to the BAR
+ # UINT8 BarIndex; ///< Which BAR to get the UART base address
+ # UINT8 RegisterStride; ///< UART register stride in bytes. Set to 0 for default register stride of 1 byte.
+ # UINT16 ReceiveFifoDepth; ///< UART receive FIFO depth in bytes. Set to 0 for a default FIFO depth of 16 bytes.
+ # UINT16 TransmitFifoDepth; ///< UART transmit FIFO depth in bytes. Set to 0 for a default FIFO depth of 16 bytes.
+ # UINT8 Reserved[2];
+ # } PCI_SERIAL_PARAMETER;
+ #
+ # Vendor 0000 Device 0000 Prog Interface 1, BAR #0, Offset 0, Stride = 1, Clock 1843200 (0x1c2000)
+ #
+ # [Vendor] [Device] [----ClockRate---] [------------Offset-----------] [Bar] [Stride] [RxFifo] [TxFifo] [Rsvd] [Vendor]
+ DEFINE PCI_SERIAL_PARAMETERS = {0x00,0x00, 0x00,0x00, 0x0,0x20,0x1c,0x00, 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0, 0x00, 0x01, 0x0,0x0, 0x0,0x0, 0x0,0x0, 0xff,0xff}
+
#
# Shell options: [BUILD_SHELL, FULL_BIN, MIN_BIN, NONE, UEFI]
#
gEfiMdeModulePkgTokenSpaceGuid.PcdConOutUgaSupport|FALSE\r
\r
[PcdsFixedAtBuild]\r
- gEfiMdePkgTokenSpaceGuid.PcdReportStatusCodePropertyMask|0x7\r
- gEfiMdePkgTokenSpaceGuid.PcdDebugPrintErrorLevel|0x8000004F\r
-!if $(SOURCE_DEBUG_ENABLE)\r
- gEfiMdePkgTokenSpaceGuid.PcdDebugPropertyMask|0x17\r
-!else\r
- gEfiMdePkgTokenSpaceGuid.PcdDebugPropertyMask|0x2F\r
-!endif\r
gEfiMdeModulePkgTokenSpaceGuid.PcdMaxVariableSize|0x10000\r
gEfiMdeModulePkgTokenSpaceGuid.PcdMaxHardwareErrorVariableSize|0x8000\r
gEfiMdeModulePkgTokenSpaceGuid.PcdVariableStoreSize|0x10000\r
!endif\r
\r
[PcdsPatchableInModule.common]\r
+ gEfiMdePkgTokenSpaceGuid.PcdReportStatusCodePropertyMask|0x7
+
+ gEfiMdePkgTokenSpaceGuid.PcdDebugPrintErrorLevel|0x8000004F
+!if $(SOURCE_DEBUG_ENABLE)
+ gEfiMdePkgTokenSpaceGuid.PcdDebugPropertyMask|0x17
+!else
+ gEfiMdePkgTokenSpaceGuid.PcdDebugPropertyMask|0x2F
+!endif
+
+ #
+ # The following parameters are set by Library/PlatformHookLib
+ #
gEfiMdeModulePkgTokenSpaceGuid.PcdSerialUseMmio|FALSE\r
- gEfiMdeModulePkgTokenSpaceGuid.PcdSerialRegisterBase|0x03F8\r
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialRegisterBase|0x3f8
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialBaudRate|$(BAUD_RATE)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialRegisterStride|1
+
+ #
+ # Enable these parameters to be set on the command line
+ #
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialClockRate|$(SERIAL_CLOCK_RATE)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialLineControl|$(SERIAL_LINE_CONTROL)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialUseHardwareFlowControl|$(SERIAL_HARDWARE_FLOW_CONTROL)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialDetectCable|$(SERIAL_DETECT_CABLE)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialFifoControl|$(SERIAL_FIFO_CONTROL)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdSerialExtendedTxFifoSize|$(SERIAL_EXTENDED_TX_FIFO_SIZE)
+
+ gEfiMdePkgTokenSpaceGuid.PcdUartDefaultBaudRate|$(UART_DEFAULT_BAUD_RATE)
+ gEfiMdePkgTokenSpaceGuid.PcdUartDefaultDataBits|$(UART_DEFAULT_DATA_BITS)
+ gEfiMdePkgTokenSpaceGuid.PcdUartDefaultParity|$(UART_DEFAULT_PARITY)
+ gEfiMdePkgTokenSpaceGuid.PcdUartDefaultStopBits|$(UART_DEFAULT_STOP_BITS)
+ gEfiMdePkgTokenSpaceGuid.PcdDefaultTerminalType|$(DEFAULT_TERMINAL_TYPE)
+ gEfiMdeModulePkgTokenSpaceGuid.PcdPciSerialParameters|$(PCI_SERIAL_PARAMETERS)
\r
################################################################################\r
#\r