+[[chapter_pve_firewall]]
ifdef::manvolnum[]
pve-firewall(8)
===============
-include::attributes.txt[]
:pve-toplevel:
NAME
DESCRIPTION
-----------
endif::manvolnum[]
-
ifndef::manvolnum[]
{pve} Firewall
==============
-include::attributes.txt[]
+:pve-toplevel:
endif::manvolnum[]
ifdef::wiki[]
-:pve-toplevel:
:title: Firewall
endif::wiki[]
and aliases help to make that task easier.
While all configuration is stored on the cluster file system, the
-`iptables`-based firewall runs on each cluster node, and thus provides
+`iptables`-based firewall service runs on each cluster node, and thus provides
full isolation between virtual machines. The distributed nature of
this system also provides much higher bandwidth than a central
firewall solution.
or on a *Node* -> *Firewall*), or you can edit the configuration files
directly using your preferred editor.
-Firewall configuration files contains sections of key-value
+Firewall configuration files contain sections of key-value
pairs. Lines beginning with a `#` and blank lines are considered
-comments. Sections starts with a header line containing the section
+comments. Sections start with a header line containing the section
name enclosed in `[` and `]`.
+[[pve_firewall_cluster_wide_setup]]
Cluster Wide Setup
~~~~~~~~~~~~~~~~~~
firewall rules to access the GUI from remote.
+[[pve_firewall_host_specific_configuration]]
Host Specific Configuration
~~~~~~~~~~~~~~~~~~~~~~~~~~~
This sections contains host specific firewall rules.
-
+[[pve_firewall_vm_container_configuration]]
VM/Container Configuration
~~~~~~~~~~~~~~~~~~~~~~~~~~
can selectively enable the firewall for each interface. This is
required in addition to the general firewall `enable` option.
-The firewall requires a special network device setup, so you need to
-restart the VM/container after enabling the firewall on a network
-interface.
-
Firewall Rules
--------------
IN SSH(ACCEPT) -i net0
IN SSH(ACCEPT) -i net0 # a comment
IN SSH(ACCEPT) -i net0 -source 192.168.2.192 # only allow SSH from 192.168.2.192
-IN SSH(ACCEPT) -i net0 -source 10.0.0.1-10.0.0.10 # accept SSH for ip range
-IN SSH(ACCEPT) -i net0 -source 10.0.0.1,10.0.0.2,10.0.0.3 #accept ssh for ip list
+IN SSH(ACCEPT) -i net0 -source 10.0.0.1-10.0.0.10 # accept SSH for IP range
+IN SSH(ACCEPT) -i net0 -source 10.0.0.1,10.0.0.2,10.0.0.3 #accept ssh for IP list
IN SSH(ACCEPT) -i net0 -source +mynetgroup # accept ssh for ipset mynetgroup
IN SSH(ACCEPT) -i net0 -source myserveralias #accept ssh for alias myserveralias
----
+[[pve_firewall_security_groups]]
Security Groups
---------------
GROUP webserver
----
-
+[[pve_firewall_ip_aliases]]
IP Aliases
----------
----
# /etc/pve/firewall/cluster.fw
[ALIASES]
-local_network 1.2.3.4 # use the single ip address
+local_network 1.2.3.4 # use the single IP address
----
-
+[[pve_firewall_ip_sets]]
IP Sets
-------
----
-[[ipfilter-section]]
+[[pve_firewall_ipfilter_section]]
Standard IP set `ipfilter-net*`
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
# iptables-save
+Logging of firewall rules
+-------------------------
+
+By default, logging of traffic filtered by the firewall rules is disabled. To
+enable logging for the default firewall rules, the log-level for incommig and
+outgoing traffic has to be set in the firewall `Options` tab for the host and/or
+the VM/CT firewall.
+Logging of dropped packets is rate limited to 1 packet per second in order to
+reduce output to the log file.
+Further, only some dropped or rejected packets are logged for the standard rules.
+
+// TODO: describe standard/default rules and note which of them get logged
+
+In order to log packets filtered by user-defined firewall rules, it is possible
+to set a log-level parameter for each rule individually.
+This allows to log in a fine grained manner and independent of the log-level
+defined for the standard rules in the firewall `Options`.
+
+The log level for the rule can also be set via the firewall configuration file by
+appending a `-log <loglevel>` to the selected rule.
+Here, `<loglevel>` is one of the following flags:
+`nolog, emerg, alert, crit, err, warning, notice, info, debug`
+
+For example, the following two are ident:
+
+----
+IN REJECT -p icmp -log nolog
+IN REJECT -p icmp
+----
+
+whereas
+
+----
+IN REJECT -p icmp -log debug
+----
+
+produces a log output flagged with the `debug` level.
+
Tips and Tricks
---------------
level to allow neighbor discovery (NDP) packets to be sent and received.
Beside neighbor discovery NDP is also used for a couple of other things, like
-autoconfiguration and advertising routers.
+auto-configuration and advertising routers.
By default VMs are allowed to send out router solicitation messages (to query
for a router), and to receive router advertisement packets. This allows them to
(`ipfilter: 1`) option which can be enabled which has the same effect as adding
an `ipfilter-net*` ipset for each of the VM's network interfaces containing the
corresponding link local addresses. (See the
-<<ipfilter-section,Standard IP set `ipfilter-net*`>> section for details.)
+<<pve_firewall_ipfilter_section,Standard IP set `ipfilter-net*`>> section for details.)
Ports used by {pve}
projects / pve-docs.git / blobdiff