To simplify management, we provide 'pveceph' - a tool to install and
manage {ceph} services on {pve} nodes.
-.Ceph consists of a couple of Daemons footnote:[Ceph intro http://docs.ceph.com/docs/master/start/intro/], for use as a RBD storage:
+.Ceph consists of a couple of Daemons footnote:[Ceph intro http://docs.ceph.com/docs/luminous/start/intro/], for use as a RBD storage:
- Ceph Monitor (ceph-mon)
- Ceph Manager (ceph-mgr)
- Ceph OSD (ceph-osd; Object Storage Daemon)
WARNING: Avoid RAID controller, use host bus adapter (HBA) instead.
+[[pve_ceph_install]]
Installation of Ceph Packages
-----------------------------
pveceph createosd /dev/sd[X]
----
-NOTE: In order to select a disk in the GUI, to be more failsafe, the disk needs
+NOTE: In order to select a disk in the GUI, to be more fail-safe, the disk needs
to have a GPT footnoteref:[GPT, GPT partition table
https://en.wikipedia.org/wiki/GUID_Partition_Table] partition table. You can
create this with `gdisk /dev/sd(x)`. If there is no GPT, you cannot select the
----
NOTE: The DB stores BlueStore’s internal metadata and the WAL is BlueStore’s
-internal journal or write-ahead log. It is recommended to use a fast SSDs or
+internal journal or write-ahead log. It is recommended to use a fast SSD or
NVRAM for better performance.
~~~~~~~~~~~~~
Till Ceph luminous, Filestore was used as storage type for Ceph OSDs. It can
still be used and might give better performance in small setups, when backed by
-a NVMe SSD or similar.
+an NVMe SSD or similar.
[source,bash]
----
[thumbnail="screenshot/gui-ceph-pools.png"]
A pool is a logical group for storing objects. It holds **P**lacement
-**G**roups (PG), a collection of objects.
+**G**roups (`PG`, `pg_num`), a collection of objects.
-When no options are given, we set a
-default of **64 PGs**, a **size of 3 replicas** and a **min_size of 2 replicas**
-for serving objects in a degraded state.
+When no options are given, we set a default of **128 PGs**, a **size of 3
+replicas** and a **min_size of 2 replicas** for serving objects in a degraded
+state.
-NOTE: The default number of PGs works for 2-6 disks. Ceph throws a
-"HEALTH_WARNING" if you have too few or too many PGs in your cluster.
+NOTE: The default number of PGs works for 2-5 disks. Ceph throws a
+'HEALTH_WARNING' if you have too few or too many PGs in your cluster.
It is advised to calculate the PG number depending on your setup, you can find
the formula and the PG calculator footnote:[PG calculator
cp /etc/ceph/ceph.client.admin.keyring /etc/pve/priv/ceph/my-ceph-storage.keyring
----
+[[pveceph_fs]]
+CephFS
+------
+
+Ceph provides also a filesystem running on top of the same object storage as
+RADOS block devices do. A **M**eta**d**ata **S**erver (`MDS`) is used to map
+the RADOS backed objects to files and directories, allowing to provide a
+POSIX-compliant replicated filesystem. This allows one to have a clustered
+highly available shared filesystem in an easy way if ceph is already used. Its
+Metadata Servers guarantee that files get balanced out over the whole Ceph
+cluster, this way even high load will not overload a single host, which can be
+an issue with traditional shared filesystem approaches, like `NFS`, for
+example.
+
+{pve} supports both, using an existing xref:storage_cephfs[CephFS as storage])
+to save backups, ISO files or container templates and creating a
+hyper-converged CephFS itself.
+
+
+[[pveceph_fs_mds]]
+Metadata Server (MDS)
+~~~~~~~~~~~~~~~~~~~~~
+
+CephFS needs at least one Metadata Server to be configured and running to be
+able to work. One can simply create one through the {pve} web GUI's `Node ->
+CephFS` panel or on the command line with:
+
+----
+pveceph mds create
+----
+
+Multiple metadata servers can be created in a cluster. But with the default
+settings only one can be active at any time. If an MDS, or its node, becomes
+unresponsive (or crashes), another `standby` MDS will get promoted to `active`.
+One can speed up the hand-over between the active and a standby MDS up by using
+the 'hotstandby' parameter option on create, or if you have already created it
+you may set/add:
+
+----
+mds standby replay = true
+----
+
+in the ceph.conf respective MDS section. With this enabled, this specific MDS
+will always poll the active one, so that it can take over faster as it is in a
+`warm` state. But naturally, the active polling will cause some additional
+performance impact on your system and active `MDS`.
+
+Multiple Active MDS
+^^^^^^^^^^^^^^^^^^^
+
+Since Luminous (12.2.x) you can also have multiple active metadata servers
+running, but this is normally only useful for a high count on parallel clients,
+as else the `MDS` seldom is the bottleneck. If you want to set this up please
+refer to the ceph documentation. footnote:[Configuring multiple active MDS
+daemons http://docs.ceph.com/docs/luminous/cephfs/multimds/]
+
+[[pveceph_fs_create]]
+Create a CephFS
+~~~~~~~~~~~~~~~
+
+With {pve}'s CephFS integration into you can create a CephFS easily over the
+Web GUI, the CLI or an external API interface. Some prerequisites are required
+for this to work:
+
+.Prerequisites for a successful CephFS setup:
+- xref:pve_ceph_install[Install Ceph packages], if this was already done some
+ time ago you might want to rerun it on an up to date system to ensure that
+ also all CephFS related packages get installed.
+- xref:pve_ceph_monitors[Setup Monitors]
+- xref:pve_ceph_monitors[Setup your OSDs]
+- xref:pveceph_fs_mds[Setup at least one MDS]
+
+After this got all checked and done you can simply create a CephFS through
+either the Web GUI's `Node -> CephFS` panel or the command line tool `pveceph`,
+for example with:
+
+----
+pveceph fs create --pg_num 128 --add-storage
+----
+
+This creates a CephFS named `'cephfs'' using a pool for its data named
+`'cephfs_data'' with `128` placement groups and a pool for its metadata named
+`'cephfs_metadata'' with one quarter of the data pools placement groups (`32`).
+Check the xref:pve_ceph_pools[{pve} managed Ceph pool chapter] or visit the
+Ceph documentation for more information regarding a fitting placement group
+number (`pg_num`) for your setup footnote:[Ceph Placement Groups
+http://docs.ceph.com/docs/luminous/rados/operations/placement-groups/].
+Additionally, the `'--add-storage'' parameter will add the CephFS to the {pve}
+storage configuration after it was created successfully.
+
+Destroy CephFS
+~~~~~~~~~~~~~~
+
+WARNING: Destroying a CephFS will render all its data unusable, this cannot be
+undone!
+
+If you really want to destroy an existing CephFS you first need to stop, or
+destroy, all metadata server (`M̀DS`). You can destroy them either over the Web
+GUI or the command line interface, with:
+
+----
+pveceph mds destroy NAME
+----
+on each {pve} node hosting a MDS daemon.
+
+Then, you can remove (destroy) CephFS by issuing a:
+
+----
+ceph fs rm NAME --yes-i-really-mean-it
+----
+on a single node hosting Ceph. After this you may want to remove the created
+data and metadata pools, this can be done either over the Web GUI or the CLI
+with:
+
+----
+pveceph pool destroy NAME
+----
ifdef::manvolnum[]
include::pve-copyright.adoc[]
projects / pve-docs.git / blobdiff