Merge remote-tracking branch 'torvalds/master' into perf/core

[mirror_ubuntu-jammy-kernel.git] / Documentation / devicetree / bindings / spi / spi-samsung.txt

* Samsung SPI Controller

The Samsung SPI controller is used to interface with various devices such as flash
and display controllers using the SPI communication interface.

Required SoC Specific Properties:

- compatible: should be one of the following.
    - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
    - samsung,s3c6410-spi: for s3c6410 platforms
    - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
    - samsung,exynos5433-spi: for exynos5433 compatible controllers
    - samsung,exynos7-spi: for exynos7 platforms <DEPRECATED>

- reg: physical base address of the controller and length of memory mapped
  region.

- interrupts: The interrupt number to the cpu. The interrupt specifier format
  depends on the interrupt controller.

- dmas : Two or more DMA channel specifiers following the convention outlined
  in bindings/dma/dma.txt

- dma-names: Names for the dma channels. There must be at least one channel
  named "tx" for transmit and named "rx" for receive.

- clocks: specifies the clock IDs provided to the SPI controller; they are
  required for interacting with the controller itself, for synchronizing the bus
  and as I/O clock (the latter is required by exynos5433 and exynos7).

- clock-names: string names of the clocks in the 'clocks' property; for all the
  the devices the names must be "spi", "spi_busclkN" (where N is determined by
  "samsung,spi-src-clk"), while Exynos5433 should specify a third clock
  "spi_ioclk" for the I/O clock.

Required Board Specific Properties:

- #address-cells: should be 1.
- #size-cells: should be 0.

Optional Board Specific Properties:

- samsung,spi-src-clk: If the spi controller includes a internal clock mux to
  select the clock source for the spi bus clock, this property can be used to
  indicate the clock to be used for driving the spi bus clock. If not specified,
  the clock number 0 is used as default.

- num-cs: Specifies the number of chip select lines supported. If
  not specified, the default number of chip select lines is set to 1.

- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt)

- no-cs-readback: the CS line is disconnected, therefore the device should not
  operate based on CS signalling.

SPI Controller specific data in SPI slave nodes:

- The spi slave nodes should provide the following information which is required
  by the spi controller.

  - samsung,spi-feedback-delay: The sampling phase shift to be applied on the
    miso line (to account for any lag in the miso line). The following are the
    valid values.

      - 0: No phase shift.
      - 1: 90 degree phase shift sampling.
      - 2: 180 degree phase shift sampling.
      - 3: 270 degree phase shift sampling.

Aliases:

- All the SPI controller nodes should be represented in the aliases node using
  the following format 'spi{n}' where n is a unique number for the alias.


Example:

- SoC Specific Portion:

	spi_0: spi@12d20000 {
		compatible = "samsung,exynos4210-spi";
		reg = <0x12d20000 0x100>;
		interrupts = <0 66 0>;
		dmas = <&pdma0 5
			&pdma0 4>;
		dma-names = "tx", "rx";
		#address-cells = <1>;
		#size-cells = <0>;
	};

- Board Specific Portion:

	spi_0: spi@12d20000 {
		#address-cells = <1>;
		#size-cells = <0>;
		pinctrl-names = "default";
		pinctrl-0 = <&spi0_bus>;
		cs-gpios = <&gpa2 5 0>;

		w25q80bw@0 {
			#address-cells = <1>;
			#size-cells = <1>;
			compatible = "w25x80";
			reg = <0>;
			spi-max-frequency = <10000>;

			controller-data {
				samsung,spi-feedback-delay = <0>;
			};

			partition@0 {
				label = "U-Boot";
				reg = <0x0 0x40000>;
				read-only;
			};

			partition@40000 {
				label = "Kernel";
				reg = <0x40000 0xc0000>;
			};
		};
	};