]>
Commit | Line | Data |
---|---|---|
cc4637f7 | 1 | // SPDX-License-Identifier: GPL-2.0 |
0682edaa OJ |
2 | /* |
3 | * Samsung's Exynos4210 based Universal C210 board device tree source | |
4 | * | |
5 | * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd. | |
6 | * http://www.samsung.com | |
7 | * | |
8 | * Device tree source file for Samsung's Universal C210 board which is based on | |
9 | * Samsung's Exynos4210 rev0 SoC. | |
cc4637f7 | 10 | */ |
0682edaa OJ |
11 | |
12 | /dts-v1/; | |
3799279f | 13 | #include "exynos4210.dtsi" |
39c1c413 | 14 | #include <dt-bindings/gpio/gpio.h> |
0682edaa OJ |
15 | |
16 | / { | |
17 | model = "Samsung Universal C210 based on Exynos4210 rev0"; | |
8bdb31b4 | 18 | compatible = "samsung,universal_c210", "samsung,exynos4210", "samsung,exynos4"; |
0682edaa | 19 | |
824e4133 | 20 | memory@40000000 { |
1354835a | 21 | device_type = "memory"; |
0682edaa OJ |
22 | reg = <0x40000000 0x10000000 |
23 | 0x50000000 0x10000000>; | |
24 | }; | |
25 | ||
26 | chosen { | |
27 | bootargs = "console=ttySAC2,115200N8 root=/dev/mmcblk0p5 rw rootwait earlyprintk panic=5 maxcpus=1"; | |
62d38099 | 28 | stdout-path = &serial_2; |
0682edaa OJ |
29 | }; |
30 | ||
0682edaa OJ |
31 | |
32 | fixed-rate-clocks { | |
33 | xxti { | |
34 | compatible = "samsung,clock-xxti"; | |
35 | clock-frequency = <0>; | |
36 | }; | |
37 | ||
38 | xusbxti { | |
39 | compatible = "samsung,clock-xusbxti"; | |
40 | clock-frequency = <24000000>; | |
41 | }; | |
42 | }; | |
43 | ||
44 | vemmc_reg: voltage-regulator { | |
45 | compatible = "regulator-fixed"; | |
46 | regulator-name = "VMEM_VDD_2_8V"; | |
47 | regulator-min-microvolt = <2800000>; | |
48 | regulator-max-microvolt = <2800000>; | |
39c1c413 | 49 | gpio = <&gpe1 3 GPIO_ACTIVE_HIGH>; |
0682edaa OJ |
50 | enable-active-high; |
51 | }; | |
52 | ||
0682edaa OJ |
53 | gpio-keys { |
54 | compatible = "gpio-keys"; | |
55 | ||
56 | vol-up-key { | |
39c1c413 | 57 | gpios = <&gpx2 0 GPIO_ACTIVE_LOW>; |
0682edaa OJ |
58 | linux,code = <115>; |
59 | label = "volume up"; | |
60 | debounce-interval = <1>; | |
61 | }; | |
62 | ||
63 | vol-down-key { | |
39c1c413 | 64 | gpios = <&gpx2 1 GPIO_ACTIVE_LOW>; |
0682edaa OJ |
65 | linux,code = <114>; |
66 | label = "volume down"; | |
67 | debounce-interval = <1>; | |
68 | }; | |
69 | ||
70 | config-key { | |
39c1c413 | 71 | gpios = <&gpx2 2 GPIO_ACTIVE_LOW>; |
0682edaa OJ |
72 | linux,code = <171>; |
73 | label = "config"; | |
74 | debounce-interval = <1>; | |
36a0282a | 75 | wakeup-source; |
0682edaa OJ |
76 | }; |
77 | ||
78 | camera-key { | |
39c1c413 | 79 | gpios = <&gpx2 3 GPIO_ACTIVE_LOW>; |
0682edaa OJ |
80 | linux,code = <212>; |
81 | label = "camera"; | |
82 | debounce-interval = <1>; | |
83 | }; | |
84 | ||
85 | power-key { | |
39c1c413 | 86 | gpios = <&gpx2 7 GPIO_ACTIVE_LOW>; |
0682edaa OJ |
87 | linux,code = <116>; |
88 | label = "power"; | |
89 | debounce-interval = <1>; | |
36a0282a | 90 | wakeup-source; |
0682edaa OJ |
91 | }; |
92 | ||
93 | ok-key { | |
39c1c413 | 94 | gpios = <&gpx3 5 GPIO_ACTIVE_LOW>; |
0682edaa OJ |
95 | linux,code = <352>; |
96 | label = "ok"; | |
97 | debounce-interval = <1>; | |
98 | }; | |
99 | }; | |
100 | ||
101 | tsp_reg: voltage-regulator { | |
102 | compatible = "regulator-fixed"; | |
103 | regulator-name = "TSP_2_8V"; | |
104 | regulator-min-microvolt = <2800000>; | |
105 | regulator-max-microvolt = <2800000>; | |
39c1c413 | 106 | gpio = <&gpe2 3 GPIO_ACTIVE_HIGH>; |
0682edaa OJ |
107 | enable-active-high; |
108 | }; | |
109 | ||
ffff29d1 AH |
110 | spi-lcd { |
111 | compatible = "spi-gpio"; | |
112 | #address-cells = <1>; | |
113 | #size-cells = <0>; | |
114 | ||
39c1c413 JMC |
115 | gpio-sck = <&gpy3 1 GPIO_ACTIVE_HIGH>; |
116 | gpio-mosi = <&gpy3 3 GPIO_ACTIVE_HIGH>; | |
ffff29d1 | 117 | num-chipselects = <1>; |
39c1c413 | 118 | cs-gpios = <&gpy4 3 GPIO_ACTIVE_HIGH>; |
ffff29d1 AH |
119 | |
120 | lcd@0 { | |
121 | compatible = "samsung,ld9040"; | |
122 | reg = <0>; | |
123 | vdd3-supply = <&ldo7_reg>; | |
124 | vci-supply = <&ldo17_reg>; | |
39c1c413 | 125 | reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>; |
ffff29d1 AH |
126 | spi-max-frequency = <1200000>; |
127 | spi-cpol; | |
128 | spi-cpha; | |
129 | power-on-delay = <10>; | |
130 | reset-delay = <10>; | |
131 | panel-width-mm = <90>; | |
132 | panel-height-mm = <154>; | |
133 | display-timings { | |
134 | timing { | |
135 | clock-frequency = <23492370>; | |
136 | hactive = <480>; | |
137 | vactive = <800>; | |
138 | hback-porch = <16>; | |
139 | hfront-porch = <16>; | |
140 | vback-porch = <2>; | |
141 | vfront-porch = <28>; | |
142 | hsync-len = <2>; | |
143 | vsync-len = <1>; | |
144 | hsync-active = <0>; | |
145 | vsync-active = <0>; | |
146 | de-active = <0>; | |
147 | pixelclk-active = <0>; | |
148 | }; | |
149 | }; | |
150 | port { | |
151 | lcd_ep: endpoint { | |
152 | remote-endpoint = <&fimd_dpi_ep>; | |
153 | }; | |
154 | }; | |
155 | }; | |
156 | }; | |
157 | ||
7daa0be1 TS |
158 | hdmi_en: voltage-regulator-hdmi-5v { |
159 | compatible = "regulator-fixed"; | |
160 | regulator-name = "HDMI_5V"; | |
161 | regulator-min-microvolt = <5000000>; | |
162 | regulator-max-microvolt = <5000000>; | |
39c1c413 | 163 | gpio = <&gpe0 1 GPIO_ACTIVE_HIGH>; |
7daa0be1 TS |
164 | enable-active-high; |
165 | }; | |
166 | ||
167 | hdmi_ddc: i2c-ddc { | |
168 | compatible = "i2c-gpio"; | |
39c1c413 | 169 | gpios = <&gpe4 2 GPIO_ACTIVE_HIGH &gpe4 3 GPIO_ACTIVE_HIGH>; |
7daa0be1 TS |
170 | i2c-gpio,delay-us = <100>; |
171 | #address-cells = <1>; | |
172 | #size-cells = <0>; | |
173 | ||
174 | pinctrl-0 = <&i2c_ddc_bus>; | |
175 | pinctrl-names = "default"; | |
176 | status = "okay"; | |
177 | }; | |
86869d66 | 178 | }; |
7daa0be1 | 179 | |
7eba413c MP |
180 | &camera { |
181 | status = "okay"; | |
182 | ||
183 | pinctrl-names = "default"; | |
184 | pinctrl-0 = <>; | |
185 | }; | |
186 | ||
86869d66 KK |
187 | &cpu0 { |
188 | cpu0-supply = <&vdd_arm_reg>; | |
189 | }; | |
190 | ||
191 | &ehci { | |
192 | status = "okay"; | |
193 | port@0 { | |
7daa0be1 TS |
194 | status = "okay"; |
195 | }; | |
86869d66 | 196 | }; |
7daa0be1 | 197 | |
86869d66 KK |
198 | &exynos_usbphy { |
199 | status = "okay"; | |
4ae9a4c6 | 200 | vbus-supply = <&safeout1_reg>; |
86869d66 KK |
201 | }; |
202 | ||
7eba413c MP |
203 | &fimc_0 { |
204 | status = "okay"; | |
205 | assigned-clocks = <&clock CLK_MOUT_FIMC0>, | |
206 | <&clock CLK_SCLK_FIMC0>; | |
207 | assigned-clock-parents = <&clock CLK_SCLK_MPLL>; | |
208 | assigned-clock-rates = <0>, <160000000>; | |
209 | }; | |
210 | ||
211 | &fimc_1 { | |
212 | status = "okay"; | |
213 | assigned-clocks = <&clock CLK_MOUT_FIMC1>, | |
214 | <&clock CLK_SCLK_FIMC1>; | |
215 | assigned-clock-parents = <&clock CLK_SCLK_MPLL>; | |
216 | assigned-clock-rates = <0>, <160000000>; | |
217 | }; | |
218 | ||
219 | &fimc_2 { | |
220 | status = "okay"; | |
221 | assigned-clocks = <&clock CLK_MOUT_FIMC2>, | |
222 | <&clock CLK_SCLK_FIMC2>; | |
223 | assigned-clock-parents = <&clock CLK_SCLK_MPLL>; | |
224 | assigned-clock-rates = <0>, <160000000>; | |
225 | }; | |
226 | ||
227 | &fimc_3 { | |
228 | status = "okay"; | |
229 | assigned-clocks = <&clock CLK_MOUT_FIMC3>, | |
230 | <&clock CLK_SCLK_FIMC3>; | |
231 | assigned-clock-parents = <&clock CLK_SCLK_MPLL>; | |
232 | assigned-clock-rates = <0>, <160000000>; | |
233 | }; | |
234 | ||
86869d66 KK |
235 | &fimd { |
236 | pinctrl-0 = <&lcd_clk>, <&lcd_data24>; | |
237 | pinctrl-names = "default"; | |
238 | status = "okay"; | |
239 | samsung,invert-vden; | |
240 | samsung,invert-vclk; | |
241 | #address-cells = <1>; | |
242 | #size-cells = <0>; | |
243 | port@3 { | |
244 | reg = <3>; | |
245 | fimd_dpi_ep: endpoint { | |
246 | remote-endpoint = <&lcd_ep>; | |
247 | }; | |
7daa0be1 | 248 | }; |
86869d66 | 249 | }; |
7daa0be1 | 250 | |
86869d66 | 251 | &hdmi { |
05b01dd9 | 252 | hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>; |
86869d66 KK |
253 | pinctrl-names = "default"; |
254 | pinctrl-0 = <&hdmi_hpd>; | |
255 | hdmi-en-supply = <&hdmi_en>; | |
256 | vdd-supply = <&ldo3_reg>; | |
257 | vdd_osc-supply = <&ldo4_reg>; | |
258 | vdd_pll-supply = <&ldo3_reg>; | |
259 | ddc = <&hdmi_ddc>; | |
260 | status = "okay"; | |
261 | }; | |
262 | ||
263 | &hsotg { | |
264 | vusb_d-supply = <&ldo3_reg>; | |
265 | vusb_a-supply = <&ldo8_reg>; | |
266 | dr_mode = "peripheral"; | |
267 | status = "okay"; | |
268 | }; | |
269 | ||
270 | &i2c_3 { | |
271 | samsung,i2c-sda-delay = <100>; | |
272 | samsung,i2c-slave-addr = <0x10>; | |
273 | samsung,i2c-max-bus-freq = <100000>; | |
274 | pinctrl-0 = <&i2c3_bus>; | |
275 | pinctrl-names = "default"; | |
276 | status = "okay"; | |
277 | ||
278 | tsp@4a { | |
279 | /* TBD: Atmel maXtouch touchscreen */ | |
280 | reg = <0x4a>; | |
7daa0be1 TS |
281 | }; |
282 | }; | |
283 | ||
86869d66 KK |
284 | &i2c_5 { |
285 | samsung,i2c-sda-delay = <100>; | |
286 | samsung,i2c-slave-addr = <0x10>; | |
287 | samsung,i2c-max-bus-freq = <100000>; | |
288 | pinctrl-0 = <&i2c5_bus>; | |
289 | pinctrl-names = "default"; | |
290 | status = "okay"; | |
291 | ||
292 | vdd_arm_reg: pmic@60 { | |
293 | compatible = "maxim,max8952"; | |
294 | reg = <0x60>; | |
295 | ||
39c1c413 JMC |
296 | max8952,vid-gpios = <&gpx0 3 GPIO_ACTIVE_HIGH>, |
297 | <&gpx0 4 GPIO_ACTIVE_HIGH>; | |
86869d66 KK |
298 | max8952,default-mode = <0>; |
299 | max8952,dvs-mode-microvolt = <1250000>, <1200000>, | |
300 | <1050000>, <950000>; | |
301 | max8952,sync-freq = <0>; | |
302 | max8952,ramp-speed = <0>; | |
303 | ||
304 | regulator-name = "vdd_arm"; | |
305 | regulator-min-microvolt = <770000>; | |
306 | regulator-max-microvolt = <1400000>; | |
307 | regulator-always-on; | |
308 | regulator-boot-on; | |
309 | }; | |
310 | ||
311 | pmic@66 { | |
312 | compatible = "national,lp3974"; | |
313 | reg = <0x66>; | |
314 | ||
315 | max8998,pmic-buck1-default-dvs-idx = <0>; | |
39c1c413 JMC |
316 | max8998,pmic-buck1-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>, |
317 | <&gpx0 6 GPIO_ACTIVE_HIGH>; | |
86869d66 KK |
318 | max8998,pmic-buck1-dvs-voltage = <1100000>, <1000000>, |
319 | <1100000>, <1000000>; | |
320 | ||
321 | max8998,pmic-buck2-default-dvs-idx = <0>; | |
39c1c413 | 322 | max8998,pmic-buck2-dvs-gpio = <&gpe2 0 GPIO_ACTIVE_HIGH>; |
86869d66 KK |
323 | max8998,pmic-buck2-dvs-voltage = <1200000>, <1100000>; |
324 | ||
325 | regulators { | |
326 | ldo2_reg: LDO2 { | |
327 | regulator-name = "VALIVE_1.2V"; | |
328 | regulator-min-microvolt = <1200000>; | |
329 | regulator-max-microvolt = <1200000>; | |
330 | regulator-always-on; | |
331 | }; | |
332 | ||
333 | ldo3_reg: LDO3 { | |
334 | regulator-name = "VUSB+MIPI_1.1V"; | |
335 | regulator-min-microvolt = <1100000>; | |
336 | regulator-max-microvolt = <1100000>; | |
337 | regulator-always-on; | |
338 | }; | |
339 | ||
340 | ldo4_reg: LDO4 { | |
341 | regulator-name = "VADC_3.3V"; | |
342 | regulator-min-microvolt = <3300000>; | |
343 | regulator-max-microvolt = <3300000>; | |
344 | }; | |
345 | ||
346 | ldo5_reg: LDO5 { | |
347 | regulator-name = "VTF_2.8V"; | |
348 | regulator-min-microvolt = <2800000>; | |
349 | regulator-max-microvolt = <2800000>; | |
350 | }; | |
351 | ||
352 | ldo6_reg: LDO6 { | |
353 | regulator-name = "LDO6"; | |
354 | regulator-min-microvolt = <2000000>; | |
355 | regulator-max-microvolt = <2000000>; | |
356 | }; | |
357 | ||
358 | ldo7_reg: LDO7 { | |
359 | regulator-name = "VLCD+VMIPI_1.8V"; | |
360 | regulator-min-microvolt = <1800000>; | |
361 | regulator-max-microvolt = <1800000>; | |
362 | }; | |
363 | ||
364 | ldo8_reg: LDO8 { | |
365 | regulator-name = "VUSB+VDAC_3.3V"; | |
366 | regulator-min-microvolt = <3300000>; | |
367 | regulator-max-microvolt = <3300000>; | |
368 | regulator-always-on; | |
369 | }; | |
370 | ||
371 | ldo9_reg: LDO9 { | |
372 | regulator-name = "VCC_2.8V"; | |
373 | regulator-min-microvolt = <2800000>; | |
374 | regulator-max-microvolt = <2800000>; | |
375 | regulator-always-on; | |
376 | }; | |
377 | ||
378 | ldo10_reg: LDO10 { | |
379 | regulator-name = "VPLL_1.1V"; | |
380 | regulator-min-microvolt = <1100000>; | |
381 | regulator-max-microvolt = <1100000>; | |
382 | regulator-boot-on; | |
383 | regulator-always-on; | |
384 | }; | |
385 | ||
386 | ldo11_reg: LDO11 { | |
387 | regulator-name = "CAM_AF_3.3V"; | |
388 | regulator-min-microvolt = <3300000>; | |
389 | regulator-max-microvolt = <3300000>; | |
390 | }; | |
391 | ||
392 | ldo12_reg: LDO12 { | |
393 | regulator-name = "PS_2.8V"; | |
394 | regulator-min-microvolt = <2800000>; | |
395 | regulator-max-microvolt = <2800000>; | |
396 | }; | |
397 | ||
398 | ldo13_reg: LDO13 { | |
399 | regulator-name = "VHIC_1.2V"; | |
400 | regulator-min-microvolt = <1200000>; | |
401 | regulator-max-microvolt = <1200000>; | |
402 | }; | |
403 | ||
404 | ldo14_reg: LDO14 { | |
405 | regulator-name = "CAM_I_HOST_1.8V"; | |
406 | regulator-min-microvolt = <1800000>; | |
407 | regulator-max-microvolt = <1800000>; | |
408 | }; | |
409 | ||
410 | ldo15_reg: LDO15 { | |
411 | regulator-name = "CAM_S_DIG+FM33_CORE_1.2V"; | |
412 | regulator-min-microvolt = <1200000>; | |
413 | regulator-max-microvolt = <1200000>; | |
414 | }; | |
415 | ||
416 | ldo16_reg: LDO16 { | |
417 | regulator-name = "CAM_S_ANA_2.8V"; | |
418 | regulator-min-microvolt = <2800000>; | |
419 | regulator-max-microvolt = <2800000>; | |
420 | }; | |
421 | ||
422 | ldo17_reg: LDO17 { | |
423 | regulator-name = "VCC_3.0V_LCD"; | |
424 | regulator-min-microvolt = <3000000>; | |
425 | regulator-max-microvolt = <3000000>; | |
426 | }; | |
427 | ||
428 | buck1_reg: BUCK1 { | |
429 | regulator-name = "VINT_1.1V"; | |
430 | regulator-min-microvolt = <750000>; | |
431 | regulator-max-microvolt = <1500000>; | |
432 | regulator-boot-on; | |
433 | regulator-always-on; | |
434 | }; | |
435 | ||
436 | buck2_reg: BUCK2 { | |
437 | regulator-name = "VG3D_1.1V"; | |
438 | regulator-min-microvolt = <750000>; | |
439 | regulator-max-microvolt = <1500000>; | |
440 | regulator-boot-on; | |
441 | }; | |
442 | ||
443 | buck3_reg: BUCK3 { | |
444 | regulator-name = "VCC_1.8V"; | |
445 | regulator-min-microvolt = <1800000>; | |
446 | regulator-max-microvolt = <1800000>; | |
447 | regulator-always-on; | |
448 | }; | |
449 | ||
450 | buck4_reg: BUCK4 { | |
451 | regulator-name = "VMEM_1.2V"; | |
452 | regulator-min-microvolt = <1200000>; | |
453 | regulator-max-microvolt = <1200000>; | |
454 | regulator-always-on; | |
455 | }; | |
456 | ||
457 | ap32khz_reg: EN32KHz-AP { | |
458 | regulator-name = "32KHz AP"; | |
459 | regulator-always-on; | |
460 | }; | |
461 | ||
462 | cp32khz_reg: EN32KHz-CP { | |
463 | regulator-name = "32KHz CP"; | |
464 | }; | |
465 | ||
466 | vichg_reg: ENVICHG { | |
467 | regulator-name = "VICHG"; | |
468 | }; | |
469 | ||
470 | safeout1_reg: ESAFEOUT1 { | |
471 | regulator-name = "SAFEOUT1"; | |
86869d66 KK |
472 | }; |
473 | ||
474 | safeout2_reg: ESAFEOUT2 { | |
475 | regulator-name = "SAFEOUT2"; | |
476 | regulator-boot-on; | |
477 | }; | |
478 | }; | |
479 | }; | |
480 | }; | |
481 | ||
482 | &i2c_8 { | |
483 | status = "okay"; | |
484 | }; | |
485 | ||
7eba413c MP |
486 | &mct { |
487 | compatible = "none"; | |
488 | }; | |
489 | ||
86869d66 KK |
490 | &mdma1 { |
491 | reg = <0x12840000 0x1000>; | |
492 | }; | |
493 | ||
494 | &mixer { | |
495 | status = "okay"; | |
496 | }; | |
497 | ||
498 | &ohci { | |
499 | status = "okay"; | |
500 | port@0 { | |
501 | status = "okay"; | |
502 | }; | |
300bde79 TA |
503 | }; |
504 | ||
7daa0be1 TS |
505 | &pinctrl_1 { |
506 | hdmi_hpd: hdmi-hpd { | |
507 | samsung,pins = "gpx3-7"; | |
4b1a9e35 | 508 | samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; |
7daa0be1 TS |
509 | }; |
510 | }; | |
511 | ||
512 | &pinctrl_0 { | |
513 | i2c_ddc_bus: i2c-ddc-bus { | |
514 | samsung,pins = "gpe4-2", "gpe4-3"; | |
4b1a9e35 KK |
515 | samsung,pin-function = <EXYNOS_PIN_FUNC_2>; |
516 | samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; | |
517 | samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; | |
7daa0be1 | 518 | }; |
0682edaa | 519 | }; |
22c98592 | 520 | |
86869d66 KK |
521 | &pwm { |
522 | compatible = "samsung,s5p6440-pwm"; | |
523 | status = "okay"; | |
524 | }; | |
525 | ||
526 | &sdhci_0 { | |
527 | bus-width = <8>; | |
528 | non-removable; | |
529 | pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>; | |
530 | pinctrl-names = "default"; | |
531 | vmmc-supply = <&vemmc_reg>; | |
532 | status = "okay"; | |
533 | }; | |
534 | ||
535 | &sdhci_2 { | |
536 | bus-width = <4>; | |
537 | pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>; | |
538 | pinctrl-names = "default"; | |
539 | vmmc-supply = <&ldo5_reg>; | |
39c1c413 | 540 | cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>; |
86869d66 KK |
541 | cd-inverted; |
542 | status = "okay"; | |
543 | }; | |
544 | ||
545 | &serial_0 { | |
546 | status = "okay"; | |
e8d761b8 MS |
547 | /delete-property/dmas; |
548 | /delete-property/dma-names; | |
86869d66 KK |
549 | }; |
550 | ||
551 | &serial_1 { | |
552 | status = "okay"; | |
e8d761b8 MS |
553 | /delete-property/dmas; |
554 | /delete-property/dma-names; | |
86869d66 KK |
555 | }; |
556 | ||
557 | &serial_2 { | |
558 | status = "okay"; | |
e8d761b8 MS |
559 | /delete-property/dmas; |
560 | /delete-property/dma-names; | |
86869d66 KK |
561 | }; |
562 | ||
563 | &serial_3 { | |
564 | status = "okay"; | |
e8d761b8 MS |
565 | /delete-property/dmas; |
566 | /delete-property/dma-names; | |
22c98592 | 567 | }; |
7eba413c MP |
568 | |
569 | &sysram { | |
570 | smp-sysram@0 { | |
571 | status = "disabled"; | |
572 | }; | |
573 | ||
574 | smp-sysram@5000 { | |
575 | compatible = "samsung,exynos4210-sysram"; | |
576 | reg = <0x5000 0x1000>; | |
577 | }; | |
578 | ||
579 | smp-sysram@1f000 { | |
580 | status = "disabled"; | |
581 | }; | |
582 | }; |