]>
Commit | Line | Data |
---|---|---|
af3c0380 FV |
1 | /* |
2 | * Copyright (C) 2012 Florian Vaussard, EPFL Mobots group | |
3 | * | |
4 | * This program is free software; you can redistribute it and/or modify | |
5 | * it under the terms of the GNU General Public License version 2 as | |
6 | * published by the Free Software Foundation. | |
7 | */ | |
8 | ||
9 | /* | |
10 | * The Gumstix Overo must be combined with an expansion board. | |
11 | */ | |
12 | ||
13 | / { | |
14 | pwmleds { | |
15 | compatible = "pwm-leds"; | |
16 | ||
17 | overo { | |
18 | label = "overo:blue:COM"; | |
19 | pwms = <&twl_pwmled 1 7812500>; | |
20 | max-brightness = <127>; | |
21 | linux,default-trigger = "mmc0"; | |
22 | }; | |
23 | }; | |
24 | ||
25 | sound { | |
26 | compatible = "ti,omap-twl4030"; | |
27 | ti,model = "overo"; | |
28 | ||
29 | ti,mcbsp = <&mcbsp2>; | |
af3c0380 | 30 | }; |
94647a30 | 31 | |
dd4051bd FV |
32 | /* HS USB Port 2 Power */ |
33 | hsusb2_power: hsusb2_power_reg { | |
34 | compatible = "regulator-fixed"; | |
35 | regulator-name = "hsusb2_vbus"; | |
36 | regulator-min-microvolt = <5000000>; | |
37 | regulator-max-microvolt = <5000000>; | |
38 | gpio = <&gpio6 8 0>; /* gpio_168: vbus enable */ | |
39 | startup-delay-us = <70000>; | |
40 | enable-active-high; | |
41 | }; | |
42 | ||
43 | /* HS USB Host PHY on PORT 2 */ | |
44 | hsusb2_phy: hsusb2_phy { | |
45 | compatible = "usb-nop-xceiv"; | |
46 | reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; /* gpio_183 */ | |
47 | vcc-supply = <&hsusb2_power>; | |
48 | }; | |
49 | ||
94647a30 FV |
50 | /* Regulator to trigger the nPoweron signal of the Wifi module */ |
51 | w3cbw003c_npoweron: regulator-w3cbw003c-npoweron { | |
52 | compatible = "regulator-fixed"; | |
53 | regulator-name = "regulator-w3cbw003c-npoweron"; | |
54 | regulator-min-microvolt = <3300000>; | |
55 | regulator-max-microvolt = <3300000>; | |
56 | gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54: nPoweron */ | |
57 | enable-active-high; | |
58 | }; | |
59 | ||
60 | /* Regulator to trigger the nReset signal of the Wifi module */ | |
61 | w3cbw003c_wifi_nreset: regulator-w3cbw003c-wifi-nreset { | |
62 | pinctrl-names = "default"; | |
63 | pinctrl-0 = <&w3cbw003c_pins &w3cbw003c_2_pins>; | |
64 | compatible = "regulator-fixed"; | |
65 | regulator-name = "regulator-w3cbw003c-wifi-nreset"; | |
66 | regulator-min-microvolt = <3300000>; | |
67 | regulator-max-microvolt = <3300000>; | |
68 | gpio = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* gpio_16: WiFi nReset */ | |
69 | startup-delay-us = <10000>; | |
70 | }; | |
71 | ||
72 | /* Regulator to trigger the nReset signal of the Bluetooth module */ | |
73 | w3cbw003c_bt_nreset: regulator-w3cbw003c-bt-nreset { | |
74 | compatible = "regulator-fixed"; | |
75 | regulator-name = "regulator-w3cbw003c-bt-nreset"; | |
76 | regulator-min-microvolt = <3300000>; | |
77 | regulator-max-microvolt = <3300000>; | |
78 | gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio_164: BT nReset */ | |
79 | startup-delay-us = <10000>; | |
80 | }; | |
af3c0380 FV |
81 | }; |
82 | ||
fc177226 | 83 | &omap3_pmx_core { |
dd4051bd FV |
84 | pinctrl-names = "default"; |
85 | pinctrl-0 = < | |
86 | &hsusb2_pins | |
87 | >; | |
88 | ||
94647a30 FV |
89 | uart2_pins: pinmux_uart2_pins { |
90 | pinctrl-single,pins = < | |
91 | OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */ | |
92 | OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_dr.uart2_rts */ | |
93 | OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_clk.uart2_tx */ | |
94 | OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1) /* mcbsp3_fsx.uart2_rx */ | |
95 | >; | |
96 | }; | |
97 | ||
fc177226 FV |
98 | i2c1_pins: pinmux_i2c1_pins { |
99 | pinctrl-single,pins = < | |
100 | OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ | |
101 | OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ | |
102 | >; | |
103 | }; | |
104 | ||
105 | mmc1_pins: pinmux_mmc1_pins { | |
106 | pinctrl-single,pins = < | |
107 | OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ | |
108 | OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ | |
109 | OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ | |
110 | OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ | |
111 | OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ | |
112 | OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ | |
113 | >; | |
114 | }; | |
94647a30 FV |
115 | |
116 | mmc2_pins: pinmux_mmc2_pins { | |
117 | pinctrl-single,pins = < | |
118 | OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ | |
119 | OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ | |
120 | OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ | |
121 | OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ | |
122 | OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ | |
123 | OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ | |
124 | >; | |
125 | }; | |
126 | ||
127 | /* WiFi/BT combo */ | |
128 | w3cbw003c_pins: pinmux_w3cbw003c_pins { | |
129 | pinctrl-single,pins = < | |
130 | OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs3.gpio_54 */ | |
131 | OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */ | |
132 | >; | |
133 | }; | |
dd4051bd FV |
134 | |
135 | hsusb2_pins: pinmux_hsusb2_pins { | |
136 | pinctrl-single,pins = < | |
137 | OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ | |
138 | OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ | |
139 | OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ | |
140 | OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ | |
141 | OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ | |
142 | OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ | |
143 | OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4) /* i2c2_scl.gpio_168 */ | |
144 | OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4) /* i2c2_sda.gpio_183 */ | |
145 | >; | |
146 | }; | |
fc177226 FV |
147 | }; |
148 | ||
af3c0380 | 149 | &i2c1 { |
fc177226 FV |
150 | pinctrl-names = "default"; |
151 | pinctrl-0 = <&i2c1_pins>; | |
af3c0380 FV |
152 | clock-frequency = <2600000>; |
153 | ||
154 | twl: twl@48 { | |
155 | reg = <0x48>; | |
156 | interrupts = <7>; /* SYS_NIRQ cascaded to intc */ | |
157 | interrupt-parent = <&intc>; | |
158 | ||
159 | twl_audio: audio { | |
160 | compatible = "ti,twl4030-audio"; | |
161 | codec { | |
162 | }; | |
163 | }; | |
164 | }; | |
165 | }; | |
166 | ||
167 | #include "twl4030.dtsi" | |
168 | #include "twl4030_omap3.dtsi" | |
169 | ||
170 | /* i2c2 pins are used for gpio */ | |
171 | &i2c2 { | |
172 | status = "disabled"; | |
173 | }; | |
174 | ||
175 | /* on board microSD slot */ | |
176 | &mmc1 { | |
fc177226 FV |
177 | pinctrl-names = "default"; |
178 | pinctrl-0 = <&mmc1_pins>; | |
af3c0380 FV |
179 | vmmc-supply = <&vmmc1>; |
180 | bus-width = <4>; | |
181 | }; | |
182 | ||
183 | /* optional on board WiFi */ | |
184 | &mmc2 { | |
94647a30 FV |
185 | pinctrl-names = "default"; |
186 | pinctrl-0 = <&mmc2_pins>; | |
187 | vmmc-supply = <&w3cbw003c_npoweron>; | |
188 | vqmmc-supply = <&w3cbw003c_bt_nreset>; | |
189 | vmmc_aux-supply = <&w3cbw003c_wifi_nreset>; | |
af3c0380 | 190 | bus-width = <4>; |
94647a30 FV |
191 | cap-sdio-irq; |
192 | non-removable; | |
af3c0380 FV |
193 | }; |
194 | ||
195 | &twl_gpio { | |
196 | ti,use-leds; | |
197 | }; | |
198 | ||
199 | &usb_otg_hs { | |
200 | interface-type = <0>; | |
201 | usb-phy = <&usb2_phy>; | |
202 | phys = <&usb2_phy>; | |
203 | phy-names = "usb2-phy"; | |
204 | mode = <3>; | |
205 | power = <50>; | |
206 | }; | |
207 | ||
dd4051bd FV |
208 | &usbhshost { |
209 | port2-mode = "ehci-phy"; | |
210 | }; | |
211 | ||
212 | &usbhsehci { | |
213 | phys = <0 &hsusb2_phy>; | |
214 | }; | |
215 | ||
94647a30 FV |
216 | &uart2 { |
217 | pinctrl-names = "default"; | |
218 | pinctrl-0 = <&uart2_pins>; | |
219 | }; | |
220 | ||
d765af89 AYL |
221 | &mcbsp2 { |
222 | status = "okay"; | |
223 | }; | |
98ce6007 AC |
224 | |
225 | &gpmc { | |
226 | ranges = <0 0 0x00000000 0x20000000>; | |
227 | ||
228 | nand@0,0 { | |
229 | linux,mtd-name= "micron,mt29c4g96maz"; | |
230 | reg = <0 0 0>; | |
231 | nand-bus-width = <16>; | |
232 | gpmc,device-width = <2>; | |
233 | ti,nand-ecc-opt = "bch8"; | |
234 | ||
235 | gpmc,sync-clk-ps = <0>; | |
236 | gpmc,cs-on-ns = <0>; | |
237 | gpmc,cs-rd-off-ns = <44>; | |
238 | gpmc,cs-wr-off-ns = <44>; | |
239 | gpmc,adv-on-ns = <6>; | |
240 | gpmc,adv-rd-off-ns = <34>; | |
241 | gpmc,adv-wr-off-ns = <44>; | |
242 | gpmc,we-off-ns = <40>; | |
243 | gpmc,oe-off-ns = <54>; | |
244 | gpmc,access-ns = <64>; | |
245 | gpmc,rd-cycle-ns = <82>; | |
246 | gpmc,wr-cycle-ns = <82>; | |
247 | gpmc,wr-access-ns = <40>; | |
248 | gpmc,wr-data-mux-bus-ns = <0>; | |
249 | ||
250 | #address-cells = <1>; | |
251 | #size-cells = <1>; | |
252 | ||
253 | partition@0 { | |
254 | label = "SPL"; | |
255 | reg = <0 0x80000>; /* 512KiB */ | |
256 | }; | |
257 | partition@80000 { | |
258 | label = "U-Boot"; | |
259 | reg = <0x80000 0x1C0000>; /* 1792KiB */ | |
260 | }; | |
261 | partition@1c0000 { | |
262 | label = "Environment"; | |
263 | reg = <0x240000 0x40000>; /* 256KiB */ | |
264 | }; | |
265 | partition@280000 { | |
266 | label = "Kernel"; | |
267 | reg = <0x280000 0x800000>; /* 8192KiB */ | |
268 | }; | |
269 | partition@780000 { | |
270 | label = "Filesystem"; | |
271 | reg = <0xA80000 0>; | |
272 | /* HACK: MTDPART_SIZ_FULL=0 so fill to end */ | |
273 | }; | |
274 | }; | |
275 | }; |