[mirror_ubuntu-zesty-kernel.git] / arch / arm / boot / dts / qcom-apq8064-ifc6410.dts

#include "qcom-apq8064-v2.0.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>

/ {
	model = "Qualcomm APQ8064/IFC6410";
	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";

	aliases {
		serial0 = &gsbi7_serial;
		serial1 = &gsbi6_serial;
		i2c0 = &gsbi1_i2c;
		i2c1 = &gsbi2_i2c;
		i2c2 = &gsbi3_i2c;
		i2c3 = &gsbi4_i2c;
		spi0 = &gsbi5_spi;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	pwrseq {
		compatible = "simple-bus";

		sdcc4_pwrseq: sdcc4_pwrseq {
			pinctrl-names = "default";
			pinctrl-0 = <&wlan_default_gpios>;
			compatible = "mmc-pwrseq-simple";
			reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
		};
	};

	leds {
		compatible = "gpio-leds";
		pinctrl-names = "default";
		pinctrl-0 = <&notify_led>;

		led@1 {
			label = "apq8064:green:user1";
			gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
			default-state = "on";
		};
	};

	hdmi-out {
		compatible = "hdmi-connector";
		type = "d";

		port {
			hdmi_con: endpoint {
				remote-endpoint = <&hdmi_out>;
			};
		};
	};

	soc {
		pinctrl@800000 {
			card_detect: card_detect {
				mux {
					pins = "gpio26";
					function = "gpio";
					bias-disable;
				};
			};

			pcie_pins: pcie_pinmux {
				mux {
					pins = "gpio27";
					function = "gpio";
				};
				conf {
					pins = "gpio27";
					drive-strength = <12>;
					bias-disable;
				};
			};

			hdmi_pinctrl: hdmi-pinctrl {
				mux {
					pins = "gpio70", "gpio71", "gpio72";
					function = "hdmi";
				};

				pinconf_ddc {
					pins = "gpio70", "gpio71";
					bias-pull-up;
					drive-strength = <2>;
				};

				pinconf_hpd {
					pins = "gpio72";
					bias-pull-down;
					drive-strength = <16>;
				};
			};
		};

		rpm@108000 {
			regulators {
				vin_lvs1_3_6-supply = <&pm8921_s4>;
				vin_lvs2-supply = <&pm8921_s1>;
				vin_lvs4_5_7-supply = <&pm8921_s4>;

				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
				vdd_l24-supply = <&pm8921_s1>;
				vdd_l25-supply = <&pm8921_s1>;
				vdd_l26-supply = <&pm8921_s7>;
				vdd_l27-supply = <&pm8921_s7>;
				vdd_l28-supply = <&pm8921_s7>;


				/* Buck SMPS */
				s1 {
					regulator-always-on;
					regulator-min-microvolt = <1225000>;
					regulator-max-microvolt = <1225000>;
					qcom,switch-mode-frequency = <3200000>;
					bias-pull-down;
				};

				s3 {
					regulator-min-microvolt = <1000000>;
					regulator-max-microvolt = <1400000>;
					qcom,switch-mode-frequency = <4800000>;
				};

				s4 {
					regulator-min-microvolt	= <1800000>;
					regulator-max-microvolt	= <1800000>;
					qcom,switch-mode-frequency = <3200000>;
				};

				s7 {
					regulator-min-microvolt = <1300000>;
					regulator-max-microvolt = <1300000>;
					qcom,switch-mode-frequency = <3200000>;
				};

				l3 {
					regulator-min-microvolt = <3050000>;
					regulator-max-microvolt = <3300000>;
					bias-pull-down;
				};

				l4 {
					regulator-min-microvolt = <1000000>;
					regulator-max-microvolt = <1800000>;
					bias-pull-down;
				};

				l5 {
					regulator-min-microvolt = <2750000>;
					regulator-max-microvolt = <3000000>;
					bias-pull-down;
				};

				l6 {
					regulator-min-microvolt = <2950000>;
					regulator-max-microvolt = <2950000>;
					bias-pull-down;
				};

				l23 {
					regulator-min-microvolt = <1700000>;
					regulator-max-microvolt = <1900000>;
					bias-pull-down;
				};

				lvs1 {
					bias-pull-down;
				};

				lvs6 {
					bias-pull-down;
				};
			};
		};

		ext_3p3v: regulator-fixed@1 {
			compatible = "regulator-fixed";
			regulator-min-microvolt = <3300000>;
			regulator-max-microvolt = <3300000>;
			regulator-name = "ext_3p3v";
			regulator-type = "voltage";
			startup-delay-us = <0>;
			gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
			enable-active-high;
			regulator-boot-on;
		};

		gsbi3: gsbi@16200000 {
			status = "okay";
			qcom,mode = <GSBI_PROT_I2C>;
			i2c@16280000 {
				status = "okay";
			};
		};

		gsbi@16300000 {
			status = "okay";
			qcom,mode = <GSBI_PROT_I2C>;
			/* CAM I2C MIPI-CSI connector */
			i2c@16380000 {
				status = "okay";
			};
		};

		gsbi@12440000 {
			status = "okay";
			qcom,mode = <GSBI_PROT_I2C>;

			i2c@12460000 {
				status = "okay";
				clock-frequency = <200000>;

				eeprom@52 {
					compatible = "atmel,24c128";
					reg = <0x52>;
					pagesize = <32>;
				};
			};
		};

		gsbi@1a200000 {
			qcom,mode = <GSBI_PROT_SPI>;
			status = "okay";
			spi4: spi@1a280000 {
				status = "okay";
				num-cs = <1>;
				cs-gpios = <&tlmm_pinmux 53 0>;
			};
		};

		gsbi@16500000 {
			status = "ok";
			qcom,mode = <GSBI_PROT_UART_W_FC>;

			serial@16540000 {
				status = "ok";
				pinctrl-names = "default";
				pinctrl-0 = <&gsbi6_uart_4pins>;
			};
		};

		gsbi@16600000 {
			status = "ok";
			qcom,mode = <GSBI_PROT_I2C_UART>;
			serial@16640000 {
				status = "ok";
				pinctrl-names = "default";
				pinctrl-0 = <&gsbi7_uart_2pins>;
			};
		};

		sata_phy0: phy@1b400000 {
			status = "okay";
		};

		sata0: sata@29000000 {
			status		= "okay";
			target-supply	= <&pm8921_s4>;
		};

		/* OTG */
		usb1_phy: phy@12500000 {
			status		= "okay";
			vddcx-supply	= <&pm8921_s3>;
			v3p3-supply	= <&pm8921_l3>;
			v1p8-supply	= <&pm8921_l4>;
		};

		usb3_phy: phy@12520000 {
			status		= "okay";
			vddcx-supply	= <&pm8921_s3>;
			v3p3-supply	= <&pm8921_l3>;
			v1p8-supply	= <&pm8921_l23>;
		};

		usb4_phy: phy@12530000 {
			status		= "okay";
			vddcx-supply	= <&pm8921_s3>;
			v3p3-supply	= <&pm8921_l3>;
			v1p8-supply	= <&pm8921_l23>;
		};

		gadget1: gadget@12500000 {
			status = "okay";
		};

		/* OTG */
		usb1: usb@12500000 {
			status = "okay";
		};

		usb3: usb@12520000 {
			status = "okay";
		};

		usb4: usb@12530000 {
			status = "okay";
		};

		pci@1b500000 {
			status = "ok";
			vdda-supply = <&pm8921_s3>;
			vdda_phy-supply = <&pm8921_lvs6>;
			vdda_refclk-supply = <&ext_3p3v>;
			pinctrl-0 = <&pcie_pins>;
			pinctrl-names = "default";
			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
		};

		qcom,ssbi@500000 {
			pmic@0 {
				gpio@150 {
					wlan_default_gpios: wlan-gpios {
						pios {
							pins = "gpio43";
							function = "normal";
							bias-disable;
							power-source = <PM8921_GPIO_S4>;
						};
					};

					notify_led: nled {
						pios {
							pins = "gpio18";
							function = "normal";
							bias-disable;
							power-source = <PM8921_GPIO_S4>;
						};
					};
				};
			};
		};

		amba {
			/* eMMC */
			sdcc1: sdcc@12400000 {
				status = "okay";
				vmmc-supply = <&pm8921_l5>;
				vqmmc-supply = <&pm8921_s4>;
			};

			/* External micro SD card */
			sdcc3: sdcc@12180000 {
				status = "okay";
				vmmc-supply = <&pm8921_l6>;
				pinctrl-names	= "default";
				pinctrl-0	= <&card_detect>;
				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
			};
			/* WLAN */
			sdcc4: sdcc@121c0000 {
				status = "okay";
				vmmc-supply = <&ext_3p3v>;
				vqmmc-supply = <&pm8921_lvs1>;
				mmc-pwrseq = <&sdcc4_pwrseq>;
			};
		};

		hdmi-tx@4a00000 {
			status = "okay";

			core-vdda-supply = <&pm8921_hdmi_switch>;
			hdmi-mux-supply = <&ext_3p3v>;

			hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;

			pinctrl-names = "default";
			pinctrl-0 = <&hdmi_pinctrl>;

			ports {
				port@0 {
					endpoint {
						remote-endpoint = <&mdp_dtv_out>;
					};
				};

				port@1 {
					endpoint {
						remote-endpoint = <&hdmi_con>;
					};
				};
			};
		};

		hdmi-phy@4a00400 {
			status = "okay";

			core-vdda-supply = <&pm8921_hdmi_switch>;
		};

		mdp@5100000 {
			status = "okay";

			ports {
				port@3 {
					endpoint {
						remote-endpoint = <&hdmi_in>;
					};
				};
			};
		};
	};
};
Commit	Line	Data
f335b8af	1	#include "qcom-apq8064-v2.0.dtsi"
b4e10dd7	2	#include <dt-bindings/gpio/gpio.h>
03f00be5	3	#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
f335b8af KG	4
	5	/ {
	6	model = "Qualcomm APQ8064/IFC6410";
	7	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
	8
d5d4654e PG	9	aliases {
d5d4654e PG	10	serial0 = &gsbi7_serial;
86e252a4	11	serial1 = &gsbi6_serial;
90bd6e8f SK	12	i2c0 = &gsbi1_i2c;
	13	i2c1 = &gsbi2_i2c;
	14	i2c2 = &gsbi3_i2c;
	15	i2c3 = &gsbi4_i2c;
	16	spi0 = &gsbi5_spi;
d5d4654e PG	17	};
d5d4654e PG	18
7f9e28b6 SB	19	chosen {
	20	stdout-path = "serial0:115200n8";
	21	};
	22
03f00be5 SK	23	pwrseq {
	24	compatible = "simple-bus";
	25
	26	sdcc4_pwrseq: sdcc4_pwrseq {
	27	pinctrl-names = "default";
	28	pinctrl-0 = <&wlan_default_gpios>;
	29	compatible = "mmc-pwrseq-simple";
	30	reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
	31	};
	32	};
	33
2630a52f SK	34	leds {
	35	compatible = "gpio-leds";
	36	pinctrl-names = "default";
	37	pinctrl-0 = <&notify_led>;
	38
	39	led@1 {
	40	label = "apq8064:green:user1";
	41	gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
	42	default-state = "on";
	43	};
	44	};
	45
c809801d AT	46	hdmi-out {
	47	compatible = "hdmi-connector";
	48	type = "d";
	49
	50	port {
	51	hdmi_con: endpoint {
	52	remote-endpoint = <&hdmi_out>;
	53	};
	54	};
	55	};
	56
f335b8af	57	soc {
8c3166f5	58	pinctrl@800000 {
b4e10dd7 PG	59	card_detect: card_detect {
	60	mux {
	61	pins = "gpio26";
	62	function = "gpio";
	63	bias-disable;
	64	};
	65	};
668f4729 SV	66
	67	pcie_pins: pcie_pinmux {
	68	mux {
	69	pins = "gpio27";
	70	function = "gpio";
	71	};
	72	conf {
	73	pins = "gpio27";
	74	drive-strength = <12>;
	75	bias-disable;
	76	};
	77	};
c809801d AT	78
	79	hdmi_pinctrl: hdmi-pinctrl {
	80	mux {
	81	pins = "gpio70", "gpio71", "gpio72";
	82	function = "hdmi";
	83	};
	84
	85	pinconf_ddc {
	86	pins = "gpio70", "gpio71";
	87	bias-pull-up;
	88	drive-strength = <2>;
	89	};
	90
	91	pinconf_hpd {
	92	pins = "gpio72";
	93	bias-pull-down;
	94	drive-strength = <16>;
	95	};
	96	};
8c3166f5	97	};
8c3166f5	98
ad560450 SK	99	rpm@108000 {
	100	regulators {
	101	vin_lvs1_3_6-supply = <&pm8921_s4>;
	102	vin_lvs2-supply = <&pm8921_s1>;
	103	vin_lvs4_5_7-supply = <&pm8921_s4>;
	104
	105	vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
	106	vdd_l24-supply = <&pm8921_s1>;
	107	vdd_l25-supply = <&pm8921_s1>;
	108	vdd_l26-supply = <&pm8921_s7>;
	109	vdd_l27-supply = <&pm8921_s7>;
	110	vdd_l28-supply = <&pm8921_s7>;
	111
	112
	113	/* Buck SMPS */
2bce6e26	114	s1 {
ad560450 SK	115	regulator-always-on;
	116	regulator-min-microvolt = <1225000>;
	117	regulator-max-microvolt = <1225000>;
	118	qcom,switch-mode-frequency = <3200000>;
	119	bias-pull-down;
	120	};
	121
2bce6e26	122	s3 {
ad560450 SK	123	regulator-min-microvolt = <1000000>;
	124	regulator-max-microvolt = <1400000>;
	125	qcom,switch-mode-frequency = <4800000>;
	126	};
	127
2bce6e26	128	s4 {
ad560450 SK	129	regulator-min-microvolt = <1800000>;
	130	regulator-max-microvolt = <1800000>;
	131	qcom,switch-mode-frequency = <3200000>;
	132	};
	133
2bce6e26	134	s7 {
ad560450 SK	135	regulator-min-microvolt = <1300000>;
	136	regulator-max-microvolt = <1300000>;
	137	qcom,switch-mode-frequency = <3200000>;
	138	};
	139
2bce6e26	140	l3 {
ad560450 SK	141	regulator-min-microvolt = <3050000>;
	142	regulator-max-microvolt = <3300000>;
	143	bias-pull-down;
	144	};
	145
2bce6e26	146	l4 {
ad560450 SK	147	regulator-min-microvolt = <1000000>;
	148	regulator-max-microvolt = <1800000>;
	149	bias-pull-down;
	150	};
	151
2bce6e26	152	l5 {
2736bbac SK	153	regulator-min-microvolt = <2750000>;
	154	regulator-max-microvolt = <3000000>;
	155	bias-pull-down;
	156	};
	157
2bce6e26	158	l6 {
ad560450 SK	159	regulator-min-microvolt = <2950000>;
	160	regulator-max-microvolt = <2950000>;
	161	bias-pull-down;
	162	};
	163
2bce6e26	164	l23 {
ad560450 SK	165	regulator-min-microvolt = <1700000>;
	166	regulator-max-microvolt = <1900000>;
	167	bias-pull-down;
	168	};
2736bbac	169
2bce6e26	170	lvs1 {
2736bbac SK	171	bias-pull-down;
2736bbac SK	172	};
668f4729 SV	173
	174	lvs6 {
	175	bias-pull-down;
	176	};
ad560450 SK	177	};
	178	};
	179
2736bbac SK	180	ext_3p3v: regulator-fixed@1 {
	181	compatible = "regulator-fixed";
	182	regulator-min-microvolt = <3300000>;
	183	regulator-max-microvolt = <3300000>;
	184	regulator-name = "ext_3p3v";
	185	regulator-type = "voltage";
	186	startup-delay-us = <0>;
	187	gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
	188	enable-active-high;
	189	regulator-boot-on;
	190	};
	191
3f62b46b SK	192	gsbi3: gsbi@16200000 {
	193	status = "okay";
	194	qcom,mode = <GSBI_PROT_I2C>;
e07214db	195	i2c@16280000 {
3f62b46b	196	status = "okay";
3f62b46b SK	197	};
	198	};
	199
10e0c161 SK	200	gsbi@16300000 {
	201	status = "okay";
	202	qcom,mode = <GSBI_PROT_I2C>;
	203	/* CAM I2C MIPI-CSI connector */
	204	i2c@16380000 {
	205	status = "okay";
	206	};
	207	};
	208
8c3166f5	209	gsbi@12440000 {
	210	status = "okay";
	211	qcom,mode = <GSBI_PROT_I2C>;
	212
	213	i2c@12460000 {
	214	status = "okay";
	215	clock-frequency = <200000>;
8c3166f5	216
e28ce3cc	217	eeprom@52 {
8c3166f5	218	compatible = "atmel,24c128";
	219	reg = <0x52>;
	220	pagesize = <32>;
	221	};
	222	};
	223	};
	224
492731cb SK	225	gsbi@1a200000 {
	226	qcom,mode = <GSBI_PROT_SPI>;
	227	status = "okay";
	228	spi4: spi@1a280000 {
	229	status = "okay";
	230	num-cs = <1>;
	231	cs-gpios = <&tlmm_pinmux 53 0>;
	232	};
	233	};
	234
86e252a4 PG	235	gsbi@16500000 {
86e252a4 PG	236	status = "ok";
426ac151	237	qcom,mode = <GSBI_PROT_UART_W_FC>;
86e252a4 PG	238
	239	serial@16540000 {
	240	status = "ok";
86e252a4	241	pinctrl-names = "default";
7648c7bf	242	pinctrl-0 = <&gsbi6_uart_4pins>;
86e252a4 PG	243	};
	244	};
	245
f335b8af KG	246	gsbi@16600000 {
	247	status = "ok";
	248	qcom,mode = <GSBI_PROT_I2C_UART>;
	249	serial@16640000 {
	250	status = "ok";
17dbc554 SK	251	pinctrl-names = "default";
17dbc554 SK	252	pinctrl-0 = <&gsbi7_uart_2pins>;
f335b8af KG	253	};
f335b8af KG	254	};
045644ff	255
e629335f SK	256	sata_phy0: phy@1b400000 {
	257	status = "okay";
	258	};
	259
	260	sata0: sata@29000000 {
	261	status = "okay";
	262	target-supply = <&pm8921_s4>;
	263	};
	264
ea986611 SK	265	/* OTG */
	266	usb1_phy: phy@12500000 {
	267	status = "okay";
	268	vddcx-supply = <&pm8921_s3>;
	269	v3p3-supply = <&pm8921_l3>;
	270	v1p8-supply = <&pm8921_l4>;
	271	};
	272
223280b1 SK	273	usb3_phy: phy@12520000 {
	274	status = "okay";
	275	vddcx-supply = <&pm8921_s3>;
	276	v3p3-supply = <&pm8921_l3>;
	277	v1p8-supply = <&pm8921_l23>;
	278	};
	279
	280	usb4_phy: phy@12530000 {
	281	status = "okay";
	282	vddcx-supply = <&pm8921_s3>;
	283	v3p3-supply = <&pm8921_l3>;
	284	v1p8-supply = <&pm8921_l23>;
	285	};
	286
ea986611 SK	287	gadget1: gadget@12500000 {
	288	status = "okay";
	289	};
	290
	291	/* OTG */
	292	usb1: usb@12500000 {
	293	status = "okay";
	294	};
	295
223280b1 SK	296	usb3: usb@12520000 {
	297	status = "okay";
	298	};
	299
	300	usb4: usb@12530000 {
	301	status = "okay";
	302	};
	303
668f4729 SV	304	pci@1b500000 {
	305	status = "ok";
	306	vdda-supply = <&pm8921_s3>;
	307	vdda_phy-supply = <&pm8921_lvs6>;
	308	vdda_refclk-supply = <&ext_3p3v>;
	309	pinctrl-0 = <&pcie_pins>;
	310	pinctrl-names = "default";
	311	perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
	312	};
	313
03f00be5 SK	314	qcom,ssbi@500000 {
	315	pmic@0 {
	316	gpio@150 {
	317	wlan_default_gpios: wlan-gpios {
	318	pios {
	319	pins = "gpio43";
	320	function = "normal";
	321	bias-disable;
	322	power-source = <PM8921_GPIO_S4>;
	323	};
	324	};
2630a52f SK	325
	326	notify_led: nled {
	327	pios {
	328	pins = "gpio18";
	329	function = "normal";
	330	bias-disable;
	331	power-source = <PM8921_GPIO_S4>;
	332	};
	333	};
03f00be5 SK	334	};
	335	};
	336	};
	337
045644ff SK	338	amba {
	339	/* eMMC */
	340	sdcc1: sdcc@12400000 {
	341	status = "okay";
2736bbac SK	342	vmmc-supply = <&pm8921_l5>;
2736bbac SK	343	vqmmc-supply = <&pm8921_s4>;
045644ff SK	344	};
	345
	346	/* External micro SD card */
	347	sdcc3: sdcc@12180000 {
	348	status = "okay";
2736bbac	349	vmmc-supply = <&pm8921_l6>;
b4e10dd7 PG	350	pinctrl-names = "default";
	351	pinctrl-0 = <&card_detect>;
	352	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
045644ff	353	};
0be5fef1 SK	354	/* WLAN */
	355	sdcc4: sdcc@121c0000 {
	356	status = "okay";
2736bbac SK	357	vmmc-supply = <&ext_3p3v>;
2736bbac SK	358	vqmmc-supply = <&pm8921_lvs1>;
03f00be5	359	mmc-pwrseq = <&sdcc4_pwrseq>;
0be5fef1	360	};
045644ff	361	};
c809801d AT	362
	363	hdmi-tx@4a00000 {
	364	status = "okay";
	365
	366	core-vdda-supply = <&pm8921_hdmi_switch>;
	367	hdmi-mux-supply = <&ext_3p3v>;
	368
	369	hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
	370
	371	pinctrl-names = "default";
	372	pinctrl-0 = <&hdmi_pinctrl>;
	373
	374	ports {
	375	port@0 {
	376	endpoint {
	377	remote-endpoint = <&mdp_dtv_out>;
	378	};
	379	};
	380
	381	port@1 {
	382	endpoint {
	383	remote-endpoint = <&hdmi_con>;
	384	};
	385	};
	386	};
	387	};
	388
	389	hdmi-phy@4a00400 {
	390	status = "okay";
	391
	392	core-vdda-supply = <&pm8921_hdmi_switch>;
	393	};
	394
	395	mdp@5100000 {
	396	status = "okay";
	397
	398	ports {
	399	port@3 {
	400	endpoint {
	401	remote-endpoint = <&hdmi_in>;
	402	};
	403	};
	404	};
	405	};
f335b8af KG	406	};
f335b8af KG	407	};