[mirror_ubuntu-eoan-kernel.git] / arch / arm / boot / dts / ste-href-tvk1281618.dtsi

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Copyright 2012 ST-Ericsson AB
 *
 * Device Tree for the TVK1281618 UIB
 */

#include <dt-bindings/interrupt-controller/irq.h>

/ {
	gpio_keys {
		compatible = "gpio-keys";
		#address-cells = <1>;
		#size-cells = <0>;
		vdd-supply = <&ab8500_ldo_aux1_reg>;
		pinctrl-names = "default";
		pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;

		button@139 {
			/* Proximity sensor */
			gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
			linux,code = <11>; /* SW_FRONT_PROXIMITY */
			label = "SFH7741 Proximity Sensor";
		};
		button@145 {
			/* Hall sensor */
			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
			linux,code = <0>; /* SW_LID */
			label = "HED54XXU11 Hall Effect Sensor";
		};
	};

	soc {
		i2c@80004000 {
			tc35893@44 {
				compatible = "toshiba,tc35893";
				reg = <0x44>;
				interrupt-parent = <&gpio6>;
				interrupts = <26 IRQ_TYPE_EDGE_RISING>;
				pinctrl-names = "default";
				pinctrl-0 = <&tc35893_tvk_mode>;

				interrupt-controller;
				#interrupt-cells = <1>;

				tc3589x_gpio {
					compatible = "toshiba,tc3589x-gpio";
					interrupts = <0>;

					interrupt-controller;
					#interrupt-cells = <2>;
					gpio-controller;
					#gpio-cells = <2>;
				};
				tc3589x_keypad {
					compatible = "toshiba,tc3589x-keypad";
					interrupts = <6>;
					debounce-delay-ms = <4>;
					keypad,num-columns = <8>;
					keypad,num-rows = <8>;
					linux,no-autorepeat;
					wakeup-source;
					linux,keymap = <0x0301006b
						        0x04010066
							0x06040072
							0x040200d7
							0x0303006a
							0x0205000e
							0x0607008b
							0x0500001c
							0x0403000b
							0x03040034
							0x05020067
							0x0305006c
							0x040500e7
							0x0005009e
							0x06020073
							0x01030039
							0x07060069
							0x050500d9>;
				};
			};
		};
		/* Sensors mounted on this board variant */
		i2c@80128000 {
			lsm303dlh@18 {
				/* Accelerometer */
				compatible = "st,lsm303dlh-accel";
				st,drdy-int-pin = <1>;
				drive-open-drain;
				reg = <0x18>;
				vdd-supply = <&ab8500_ldo_aux1_reg>;
				vddio-supply = <&db8500_vsmps2_reg>;
				pinctrl-names = "default";
				pinctrl-0 = <&accel_tvk_mode>;
				/*
				 * These interrupts cannot be used: the other component
				 * ST-Micro L3D4200D gyro that is connected to the same lines
				 * cannot set its DRDY line to open drain, so it cannot be
				 * shared with other peripherals. The should be defined for
				 * the falling edge if they could be wired together.
				 *
				 * interrupts-extended =
				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
				 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
				 */
			};
			lsm303dlh@1e {
				/* Magnetometer */
				compatible = "st,lsm303dlh-magn";
				reg = <0x1e>;
				vdd-supply = <&ab8500_ldo_aux1_reg>;
				vddio-supply = <&db8500_vsmps2_reg>;
				/*
				 * These interrupts cannot be used: the other component
				 * ST-Micro L3D4200D gyro that is connected to the same lines
				 * cannot set its DRDY line to open drain, so it cannot be
				 * shared with other peripherals. The should be defined for
				 * the falling edge if they could be wired together.
				 *
				 * interrupts-extended =
				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
				 * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
				 */
			};
			lis331dl@1c {
				/* Accelerometer */
				compatible = "st,lis331dl-accel";
				st,drdy-int-pin = <1>;
				reg = <0x1c>;
				vdd-supply = <&ab8500_ldo_aux1_reg>;
				vddio-supply = <&db8500_vsmps2_reg>;
				pinctrl-names = "default";
				pinctrl-0 = <&accel_tvk_mode>;
				interrupt-parent = <&gpio2>;
				/* INT2 would need to be open drain */
				interrupts = <18 IRQ_TYPE_EDGE_RISING>,
					     <19 IRQ_TYPE_EDGE_RISING>;
			};
			ak8974@f {
				/* Magnetometer */
				compatible = "asahi-kasei,ak8974";
				reg = <0x0f>;
				avdd-supply = <&ab8500_ldo_aux1_reg>;
				dvdd-supply = <&db8500_vsmps2_reg>;
				pinctrl-names = "default";
				pinctrl-0 = <&gyro_magn_tvk_mode>;
				/*
				 * These interrupts cannot be used: the other component
				 * ST-Micro L3D4200D gyro that is connected to the same lines
				 * cannot set its DRDY line to open drain, so it cannot be
				 * shared with other peripherals. The should be defined for
				 * the falling edge if they could be wired together.
				 *
				 * interrupts-extended =
				 * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
				 * <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
				 */
			};
			l3g4200d@68 {
				/* Gyroscope */
				compatible = "st,l3g4200d-gyro";
				st,drdy-int-pin = <2>;
				reg = <0x68>;
				vdd-supply = <&ab8500_ldo_aux1_reg>;
				vddio-supply = <&db8500_vsmps2_reg>;
				pinctrl-names = "default";
				pinctrl-0 = <&gyro_magn_tvk_mode>;
				interrupts-extended =
				<&gpio1 0 IRQ_TYPE_EDGE_RISING>,
				<&gpio0 31 IRQ_TYPE_EDGE_RISING>;
			};
			lsp001wm@5c {
				/* Barometer/pressure sensor */
				compatible = "st,lps001wp-press";
				reg = <0x5c>;
				vdd-supply = <&ab8500_ldo_aux1_reg>;
				vddio-supply = <&db8500_vsmps2_reg>;
			};
		};

		i2c@80110000 {
			synaptics@4b {
				/* Synaptics RMI4 TM1217 touchscreen */
				compatible = "syna,rmi4-i2c";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x4b>;
				vdd-supply = <&ab8500_ldo_aux1_reg>;
				vddio-supply = <&db8500_vsmps2_reg>;
				pinctrl-names = "default";
				pinctrl-0 = <&synaptics_tvk_mode>;
				interrupt-parent = <&gpio2>;
				interrupts = <20 IRQ_TYPE_EDGE_FALLING>;

				rmi-f01@1 {
					reg = <0x1>;
					syna,nosleep = <1>;
				};
				rmi-f11@11 {
					reg = <0x11>;
					touchscreen-inverted-x;
					syna,sensor-type = <1>;
				};
			};
		};

		pinctrl {
			/* Pull up this GPIO pin */
			tc35893 {
				tc35893_tvk_mode: tc35893_tvk {
					tvk_cfg {
						pins = "GPIO218_AH11";
						ste,config = <&gpio_in_pu>;
					};
				};
			};
			prox {
				prox_tvk_mode: prox_tvk {
					tvk_cfg {
						pins = "GPIO217_AH12";
						ste,config = <&gpio_in_pu>;
					};
				};
			};
			hall {
				hall_tvk_mode: hall_tvk {
					tvk_cfg {
						pins = "GPIO145_C13";
						ste,config = <&gpio_in_pu>;
					};
				};
			};
			accelerometer {
				accel_tvk_mode: accel_tvk {
					/* Accelerometer interrupt lines 1 & 2 */
					tvk_cfg {
						pins = "GPIO82_C1", "GPIO83_D3";
						ste,config = <&gpio_in_pd>;
					};
				};
			};
			gyroscope {
				/*
				 * These lines are shared between Gyroscope l3g400dh
				 * and AK8974 magnetometer.
				 */
				gyro_magn_tvk_mode: gyro_magn_tvk {
					 /* GPIO 31 used for INT pull down the line */
					tvk_cfg1 {
						pins = "GPIO31_V3";
						ste,config = <&gpio_in_pd>;
					};
					/* GPIO 32 used for DRDY, pull this down */
					tvk_cfg2 {
						pins = "GPIO32_V2";
						ste,config = <&gpio_in_pd>;
					};
				};
			};
			synaptics {
				synaptics_tvk_mode: synaptics_tvk {
					/* Touchscreen uses GPIO 84 */
					tvk_cfg1 {
						pins = "GPIO84_C2";
						ste,config = <&gpio_in_pu>;
					};
				};
			};
		};

		mcde@a0350000 {
			status = "okay";

			dsi@a0351000 {
				panel {
					compatible = "samsung,s6d16d0";
					reg = <0>;
					vdd1-supply = <&ab8500_ldo_aux1_reg>;
					reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
				};
			};
		};
	};
};
Commit	Line	Data
fcaf2036	1	// SPDX-License-Identifier: GPL-2.0-or-later
9c19cfa9 LW	2	/*
	3	* Copyright 2012 ST-Ericsson AB
	4	*
9c19cfa9 LW	5	* Device Tree for the TVK1281618 UIB
	6	*/
	7
	8	#include <dt-bindings/interrupt-controller/irq.h>
	9
	10	/ {
1a780d45 LW	11	gpio_keys {
	12	compatible = "gpio-keys";
	13	#address-cells = <1>;
	14	#size-cells = <0>;
	15	vdd-supply = <&ab8500_ldo_aux1_reg>;
	16	pinctrl-names = "default";
	17	pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
	18
	19	button@139 {
	20	/* Proximity sensor */
1b1e8e02	21	gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>;
1a780d45 LW	22	linux,code = <11>; /* SW_FRONT_PROXIMITY */
	23	label = "SFH7741 Proximity Sensor";
	24	};
	25	button@145 {
	26	/* Hall sensor */
1b1e8e02	27	gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
1a780d45 LW	28	linux,code = <0>; /* SW_LID */
	29	label = "HED54XXU11 Hall Effect Sensor";
	30	};
	31	};
	32
9c19cfa9	33	soc {
84919b96	34	i2c@80004000 {
7e0a51a0 LW	35	tc35893@44 {
7e0a51a0 LW	36	compatible = "toshiba,tc35893";
84919b96 LW	37	reg = <0x44>;
	38	interrupt-parent = <&gpio6>;
	39	interrupts = <26 IRQ_TYPE_EDGE_RISING>;
a45cb698 LW	40	pinctrl-names = "default";
a45cb698 LW	41	pinctrl-0 = <&tc35893_tvk_mode>;
84919b96 LW	42
84919b96 LW	43	interrupt-controller;
7e0a51a0	44	#interrupt-cells = <1>;
84919b96 LW	45
84919b96 LW	46	tc3589x_gpio {
7e0a51a0 LW	47	compatible = "toshiba,tc3589x-gpio";
7e0a51a0 LW	48	interrupts = <0>;
84919b96 LW	49
	50	interrupt-controller;
	51	#interrupt-cells = <2>;
	52	gpio-controller;
	53	#gpio-cells = <2>;
	54	};
7e0a51a0 LW	55	tc3589x_keypad {
	56	compatible = "toshiba,tc3589x-keypad";
	57	interrupts = <6>;
	58	debounce-delay-ms = <4>;
	59	keypad,num-columns = <8>;
	60	keypad,num-rows = <8>;
	61	linux,no-autorepeat;
506822ea	62	wakeup-source;
7e0a51a0 LW	63	linux,keymap = <0x0301006b
	64	0x04010066
	65	0x06040072
	66	0x040200d7
	67	0x0303006a
	68	0x0205000e
	69	0x0607008b
	70	0x0500001c
	71	0x0403000b
	72	0x03040034
	73	0x05020067
	74	0x0305006c
	75	0x040500e7
	76	0x0005009e
	77	0x06020073
	78	0x01030039
	79	0x07060069
	80	0x050500d9>;
	81	};
84919b96 LW	82	};
84919b96 LW	83	};
d0e3bc81 LW	84	/* Sensors mounted on this board variant */
	85	i2c@80128000 {
	86	lsm303dlh@18 {
	87	/* Accelerometer */
	88	compatible = "st,lsm303dlh-accel";
	89	st,drdy-int-pin = <1>;
7ba5dd53	90	drive-open-drain;
d0e3bc81 LW	91	reg = <0x18>;
	92	vdd-supply = <&ab8500_ldo_aux1_reg>;
	93	vddio-supply = <&db8500_vsmps2_reg>;
	94	pinctrl-names = "default";
	95	pinctrl-0 = <&accel_tvk_mode>;
2f23cda3	96	/*
83919ef0 LW	97	* These interrupts cannot be used: the other component
	98	* ST-Micro L3D4200D gyro that is connected to the same lines
	99	* cannot set its DRDY line to open drain, so it cannot be
	100	* shared with other peripherals. The should be defined for
	101	* the falling edge if they could be wired together.
	102	*
	103	* interrupts-extended =
	104	* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
	105	* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
2f23cda3	106	*/
83919ef0 LW	107	};
	108	lsm303dlh@1e {
	109	/* Magnetometer */
93deea9a	110	compatible = "st,lsm303dlh-magn";
d0e3bc81 LW	111	reg = <0x1e>;
	112	vdd-supply = <&ab8500_ldo_aux1_reg>;
	113	vddio-supply = <&db8500_vsmps2_reg>;
83919ef0 LW	114	/*
	115	* These interrupts cannot be used: the other component
	116	* ST-Micro L3D4200D gyro that is connected to the same lines
	117	* cannot set its DRDY line to open drain, so it cannot be
	118	* shared with other peripherals. The should be defined for
	119	* the falling edge if they could be wired together.
	120	*
	121	* interrupts-extended =
	122	* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
	123	* <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
	124	*/
2f23cda3 LW	125	};
	126	lis331dl@1c {
	127	/* Accelerometer */
	128	compatible = "st,lis331dl-accel";
	129	st,drdy-int-pin = <1>;
	130	reg = <0x1c>;
	131	vdd-supply = <&ab8500_ldo_aux1_reg>;
	132	vddio-supply = <&db8500_vsmps2_reg>;
	133	pinctrl-names = "default";
	134	pinctrl-0 = <&accel_tvk_mode>;
	135	interrupt-parent = <&gpio2>;
83919ef0 LW	136	/* INT2 would need to be open drain */
	137	interrupts = <18 IRQ_TYPE_EDGE_RISING>,
	138	<19 IRQ_TYPE_EDGE_RISING>;
2f23cda3	139	};
8dccafaa	140	ak8974@f {
2f23cda3 LW	141	/* Magnetometer */
	142	compatible = "asahi-kasei,ak8974";
	143	reg = <0x0f>;
83919ef0 LW	144	avdd-supply = <&ab8500_ldo_aux1_reg>;
83919ef0 LW	145	dvdd-supply = <&db8500_vsmps2_reg>;
d0e3bc81	146	pinctrl-names = "default";
2f23cda3	147	pinctrl-0 = <&gyro_magn_tvk_mode>;
83919ef0 LW	148	/*
	149	* These interrupts cannot be used: the other component
	150	* ST-Micro L3D4200D gyro that is connected to the same lines
	151	* cannot set its DRDY line to open drain, so it cannot be
	152	* shared with other peripherals. The should be defined for
	153	* the falling edge if they could be wired together.
	154	*
	155	* interrupts-extended =
	156	* <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
	157	* <&gpio0 31 IRQ_TYPE_EDGE_FALLING>;
	158	*/
d0e3bc81 LW	159	};
	160	l3g4200d@68 {
	161	/* Gyroscope */
	162	compatible = "st,l3g4200d-gyro";
	163	st,drdy-int-pin = <2>;
	164	reg = <0x68>;
	165	vdd-supply = <&ab8500_ldo_aux1_reg>;
	166	vddio-supply = <&db8500_vsmps2_reg>;
2f23cda3 LW	167	pinctrl-names = "default";
2f23cda3 LW	168	pinctrl-0 = <&gyro_magn_tvk_mode>;
83919ef0 LW	169	interrupts-extended =
	170	<&gpio1 0 IRQ_TYPE_EDGE_RISING>,
	171	<&gpio0 31 IRQ_TYPE_EDGE_RISING>;
d0e3bc81 LW	172	};
	173	lsp001wm@5c {
	174	/* Barometer/pressure sensor */
	175	compatible = "st,lps001wp-press";
	176	reg = <0x5c>;
	177	vdd-supply = <&ab8500_ldo_aux1_reg>;
	178	vddio-supply = <&db8500_vsmps2_reg>;
	179	};
	180	};
7ad86d61 LW	181
	182	i2c@80110000 {
	183	synaptics@4b {
	184	/* Synaptics RMI4 TM1217 touchscreen */
	185	compatible = "syna,rmi4-i2c";
	186	#address-cells = <1>;
	187	#size-cells = <0>;
	188	reg = <0x4b>;
	189	vdd-supply = <&ab8500_ldo_aux1_reg>;
	190	vddio-supply = <&db8500_vsmps2_reg>;
	191	pinctrl-names = "default";
	192	pinctrl-0 = <&synaptics_tvk_mode>;
	193	interrupt-parent = <&gpio2>;
	194	interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
	195
	196	rmi-f01@1 {
	197	reg = <0x1>;
	198	syna,nosleep = <1>;
	199	};
	200	rmi-f11@11 {
	201	reg = <0x11>;
	202	touchscreen-inverted-x;
	203	syna,sensor-type = <1>;
	204	};
	205	};
	206	};
	207
a45cb698 LW	208	pinctrl {
	209	/* Pull up this GPIO pin */
	210	tc35893 {
	211	tc35893_tvk_mode: tc35893_tvk {
	212	tvk_cfg {
1637d480	213	pins = "GPIO218_AH11";
a45cb698 LW	214	ste,config = <&gpio_in_pu>;
	215	};
	216	};
	217	};
1a780d45 LW	218	prox {
	219	prox_tvk_mode: prox_tvk {
	220	tvk_cfg {
1637d480	221	pins = "GPIO217_AH12";
1a780d45 LW	222	ste,config = <&gpio_in_pu>;
	223	};
	224	};
	225	};
	226	hall {
	227	hall_tvk_mode: hall_tvk {
	228	tvk_cfg {
1637d480	229	pins = "GPIO145_C13";
1a780d45 LW	230	ste,config = <&gpio_in_pu>;
	231	};
	232	};
	233	};
d0e3bc81 LW	234	accelerometer {
	235	accel_tvk_mode: accel_tvk {
	236	/* Accelerometer interrupt lines 1 & 2 */
	237	tvk_cfg {
1637d480	238	pins = "GPIO82_C1", "GPIO83_D3";
83919ef0	239	ste,config = <&gpio_in_pd>;
d0e3bc81 LW	240	};
	241	};
	242	};
2f23cda3 LW	243	gyroscope {
	244	/*
	245	* These lines are shared between Gyroscope l3g400dh
	246	* and AK8974 magnetometer.
	247	*/
	248	gyro_magn_tvk_mode: gyro_magn_tvk {
	249	/* GPIO 31 used for INT pull down the line */
d0e3bc81	250	tvk_cfg1 {
1637d480	251	pins = "GPIO31_V3";
2f23cda3	252	ste,config = <&gpio_in_pd>;
d0e3bc81	253	};
2f23cda3	254	/* GPIO 32 used for DRDY, pull this down */
d0e3bc81	255	tvk_cfg2 {
1637d480	256	pins = "GPIO32_V2";
d0e3bc81 LW	257	ste,config = <&gpio_in_pd>;
	258	};
	259	};
	260	};
7ad86d61 LW	261	synaptics {
	262	synaptics_tvk_mode: synaptics_tvk {
	263	/* Touchscreen uses GPIO 84 */
	264	tvk_cfg1 {
	265	pins = "GPIO84_C2";
	266	ste,config = <&gpio_in_pu>;
	267	};
	268	};
	269	};
a45cb698	270	};
f4bdfcc2 LW	271
	272	mcde@a0350000 {
	273	status = "okay";
	274
	275	dsi@a0351000 {
	276	panel {
	277	compatible = "samsung,s6d16d0";
	278	reg = <0>;
	279	vdd1-supply = <&ab8500_ldo_aux1_reg>;
	280	reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
	281	};
	282	};
	283	};
9c19cfa9 LW	284	};
9c19cfa9 LW	285	};