]>
Commit | Line | Data |
---|---|---|
ca0a789a AV |
1 | /* |
2 | * linux/arch/arm/mach-at91/board-qil-a9260.c | |
3 | * | |
4 | * Copyright (C) 2005 SAN People | |
5 | * Copyright (C) 2006 Atmel | |
6 | * Copyright (C) 2007 Calao-systems | |
7 | * | |
8 | * This program is free software; you can redistribute it and/or modify | |
9 | * it under the terms of the GNU General Public License as published by | |
10 | * the Free Software Foundation; either version 2 of the License, or | |
11 | * (at your option) any later version. | |
12 | * | |
13 | * This program is distributed in the hope that it will be useful, | |
14 | * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
15 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
16 | * GNU General Public License for more details. | |
17 | * | |
18 | * You should have received a copy of the GNU General Public License | |
19 | * along with this program; if not, write to the Free Software | |
20 | * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA | |
21 | */ | |
22 | ||
23 | #include <linux/types.h> | |
2f8163ba | 24 | #include <linux/gpio.h> |
ca0a789a AV |
25 | #include <linux/init.h> |
26 | #include <linux/mm.h> | |
27 | #include <linux/module.h> | |
28 | #include <linux/platform_device.h> | |
29 | #include <linux/spi/spi.h> | |
30 | #include <linux/gpio_keys.h> | |
31 | #include <linux/input.h> | |
32 | #include <linux/clk.h> | |
33 | ||
ca0a789a AV |
34 | #include <asm/setup.h> |
35 | #include <asm/mach-types.h> | |
36 | #include <asm/irq.h> | |
37 | ||
38 | #include <asm/mach/arch.h> | |
39 | #include <asm/mach/map.h> | |
40 | #include <asm/mach/irq.h> | |
41 | ||
e505240b | 42 | #include <mach/hardware.h> |
a09e64fb | 43 | #include <mach/board.h> |
3e135466 | 44 | #include <mach/at91_aic.h> |
8cdae51a | 45 | #include <mach/at91sam9_smc.h> |
a09e64fb | 46 | #include <mach/at91_shdwc.h> |
ca0a789a | 47 | |
8cdae51a | 48 | #include "sam9_smc.h" |
ca0a789a AV |
49 | #include "generic.h" |
50 | ||
51 | ||
1b021a3b | 52 | static void __init ek_init_early(void) |
ca0a789a AV |
53 | { |
54 | /* Initialize processor: 12.000 MHz crystal */ | |
21d08b9d | 55 | at91_initialize(12000000); |
ca0a789a AV |
56 | } |
57 | ||
ca0a789a AV |
58 | /* |
59 | * USB Host port | |
60 | */ | |
61 | static struct at91_usbh_data __initdata ek_usbh_data = { | |
62 | .ports = 2, | |
63b4c296 JCPV |
63 | .vbus_pin = {-EINVAL, -EINVAL}, |
64 | .overcurrent_pin= {-EINVAL, -EINVAL}, | |
ca0a789a AV |
65 | }; |
66 | ||
67 | /* | |
68 | * USB Device port | |
69 | */ | |
70 | static struct at91_udc_data __initdata ek_udc_data = { | |
71 | .vbus_pin = AT91_PIN_PC5, | |
63b4c296 | 72 | .pullup_pin = -EINVAL, /* pull-up driven by UDC */ |
ca0a789a AV |
73 | }; |
74 | ||
75 | /* | |
76 | * SPI devices. | |
77 | */ | |
78 | static struct spi_board_info ek_spi_devices[] = { | |
79 | #if defined(CONFIG_RTC_DRV_M41T94) | |
80 | { /* M41T94 RTC */ | |
81 | .modalias = "m41t94", | |
82 | .chip_select = 0, | |
83 | .max_speed_hz = 1 * 1000 * 1000, | |
84 | .bus_num = 0, | |
85 | } | |
86 | #endif | |
87 | }; | |
88 | ||
89 | /* | |
90 | * MACB Ethernet device | |
91 | */ | |
84e0cdb0 | 92 | static struct macb_platform_data __initdata ek_macb_data = { |
ca0a789a AV |
93 | .phy_irq_pin = AT91_PIN_PA31, |
94 | .is_rmii = 1, | |
95 | }; | |
96 | ||
97 | /* | |
98 | * NAND flash | |
99 | */ | |
100 | static struct mtd_partition __initdata ek_nand_partition[] = { | |
101 | { | |
102 | .name = "Uboot & Kernel", | |
e505240b AV |
103 | .offset = 0, |
104 | .size = SZ_16M, | |
ca0a789a AV |
105 | }, |
106 | { | |
107 | .name = "Root FS", | |
e505240b AV |
108 | .offset = MTDPART_OFS_NXTBLK, |
109 | .size = 120 * SZ_1M, | |
ca0a789a AV |
110 | }, |
111 | { | |
112 | .name = "FS", | |
e505240b AV |
113 | .offset = MTDPART_OFS_NXTBLK, |
114 | .size = 120 * SZ_1M, | |
ca0a789a AV |
115 | }, |
116 | }; | |
117 | ||
7c896834 | 118 | static struct atmel_nand_data __initdata ek_nand_data = { |
ca0a789a AV |
119 | .ale = 21, |
120 | .cle = 22, | |
63b4c296 | 121 | .det_pin = -EINVAL, |
ca0a789a AV |
122 | .rdy_pin = AT91_PIN_PC13, |
123 | .enable_pin = AT91_PIN_PC14, | |
bf4289cb | 124 | .ecc_mode = NAND_ECC_SOFT, |
98619dcb | 125 | .on_flash_bbt = 1, |
1754aab9 DES |
126 | .parts = ek_nand_partition, |
127 | .num_parts = ARRAY_SIZE(ek_nand_partition), | |
ca0a789a AV |
128 | }; |
129 | ||
8cdae51a AV |
130 | static struct sam9_smc_config __initdata ek_nand_smc_config = { |
131 | .ncs_read_setup = 0, | |
132 | .nrd_setup = 1, | |
133 | .ncs_write_setup = 0, | |
134 | .nwe_setup = 1, | |
135 | ||
136 | .ncs_read_pulse = 3, | |
137 | .nrd_pulse = 3, | |
138 | .ncs_write_pulse = 3, | |
139 | .nwe_pulse = 3, | |
140 | ||
141 | .read_cycle = 5, | |
142 | .write_cycle = 5, | |
143 | ||
144 | .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8, | |
145 | .tdf_cycles = 2, | |
146 | }; | |
147 | ||
148 | static void __init ek_add_device_nand(void) | |
149 | { | |
150 | /* configure chip-select 3 (NAND) */ | |
faee0cc3 | 151 | sam9_smc_configure(0, 3, &ek_nand_smc_config); |
8cdae51a AV |
152 | |
153 | at91_add_device_nand(&ek_nand_data); | |
154 | } | |
155 | ||
ca0a789a AV |
156 | /* |
157 | * MCI (SD/MMC) | |
158 | */ | |
4cf3326a LD |
159 | static struct mci_platform_data __initdata ek_mci0_data = { |
160 | .slot[0] = { | |
161 | .bus_width = 4, | |
162 | .detect_pin = -EINVAL, | |
163 | .wp_pin = -EINVAL, | |
164 | }, | |
ca0a789a AV |
165 | }; |
166 | ||
167 | /* | |
168 | * GPIO Buttons | |
169 | */ | |
170 | #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) | |
171 | static struct gpio_keys_button ek_buttons[] = { | |
172 | { /* USER PUSH BUTTON */ | |
173 | .code = KEY_ENTER, | |
174 | .gpio = AT91_PIN_PB10, | |
175 | .active_low = 1, | |
176 | .desc = "user_pb", | |
177 | .wakeup = 1, | |
178 | } | |
179 | }; | |
180 | ||
181 | static struct gpio_keys_platform_data ek_button_data = { | |
182 | .buttons = ek_buttons, | |
183 | .nbuttons = ARRAY_SIZE(ek_buttons), | |
184 | }; | |
185 | ||
186 | static struct platform_device ek_button_device = { | |
187 | .name = "gpio-keys", | |
188 | .id = -1, | |
189 | .num_resources = 0, | |
190 | .dev = { | |
191 | .platform_data = &ek_button_data, | |
192 | } | |
193 | }; | |
194 | ||
195 | static void __init ek_add_device_buttons(void) | |
196 | { | |
197 | at91_set_GPIO_periph(AT91_PIN_PB10, 1); /* user push button, pull up enabled */ | |
198 | at91_set_deglitch(AT91_PIN_PB10, 1); | |
199 | ||
200 | platform_device_register(&ek_button_device); | |
201 | } | |
202 | #else | |
203 | static void __init ek_add_device_buttons(void) {} | |
204 | #endif | |
205 | ||
206 | /* | |
207 | * LEDs | |
208 | */ | |
209 | static struct gpio_led ek_leds[] = { | |
210 | { /* user_led (green) */ | |
211 | .name = "user_led", | |
212 | .gpio = AT91_PIN_PB21, | |
213 | .active_low = 0, | |
214 | .default_trigger = "heartbeat", | |
215 | } | |
216 | }; | |
217 | ||
218 | static void __init ek_board_init(void) | |
219 | { | |
220 | /* Serial */ | |
71b149b3 JCPV |
221 | /* DBGU on ttyS0. (Rx & Tx only) */ |
222 | at91_register_uart(0, 0, 0); | |
223 | ||
224 | /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ | |
225 | at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS | |
226 | | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD | |
227 | | ATMEL_UART_RI); | |
228 | ||
229 | /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */ | |
230 | at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS); | |
231 | ||
232 | /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */ | |
233 | at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS); | |
ca0a789a AV |
234 | at91_add_device_serial(); |
235 | /* USB Host */ | |
236 | at91_add_device_usbh(&ek_usbh_data); | |
237 | /* USB Device */ | |
238 | at91_add_device_udc(&ek_udc_data); | |
239 | /* SPI */ | |
240 | at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices)); | |
241 | /* NAND */ | |
8cdae51a | 242 | ek_add_device_nand(); |
ca0a789a AV |
243 | /* I2C */ |
244 | at91_add_device_i2c(NULL, 0); | |
245 | /* Ethernet */ | |
246 | at91_add_device_eth(&ek_macb_data); | |
247 | /* MMC */ | |
4cf3326a | 248 | at91_add_device_mci(0, &ek_mci0_data); |
ca0a789a AV |
249 | /* Push Buttons */ |
250 | ek_add_device_buttons(); | |
251 | /* LEDs */ | |
252 | at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); | |
253 | /* shutdown controller, wakeup button (5 msec low) */ | |
f22deee5 | 254 | at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW |
ca0a789a AV |
255 | | AT91_SHDW_RTTWKEN); |
256 | } | |
257 | ||
258 | MACHINE_START(QIL_A9260, "CALAO QIL_A9260") | |
259 | /* Maintainer: calao-systems */ | |
ca0a789a | 260 | .timer = &at91sam926x_timer, |
21d08b9d | 261 | .map_io = at91_map_io, |
3e135466 | 262 | .handle_irq = at91_aic_handle_irq, |
1b021a3b | 263 | .init_early = ek_init_early, |
92100c12 | 264 | .init_irq = at91_init_irq_default, |
ca0a789a AV |
265 | .init_machine = ek_board_init, |
266 | MACHINE_END |