]>
Commit | Line | Data |
---|---|---|
1394f032 BW |
1 | #ifndef __BFIN_ENTRY_H |
2 | #define __BFIN_ENTRY_H | |
3 | ||
4 | #include <asm/setup.h> | |
5 | #include <asm/page.h> | |
6 | ||
7 | #ifdef __ASSEMBLY__ | |
8 | ||
9 | #define LFLUSH_I_AND_D 0x00000808 | |
10 | #define LSIGTRAP 5 | |
11 | ||
12 | /* process bits for task_struct.flags */ | |
13 | #define PF_TRACESYS_OFF 3 | |
14 | #define PF_TRACESYS_BIT 5 | |
15 | #define PF_PTRACED_OFF 3 | |
16 | #define PF_PTRACED_BIT 4 | |
17 | #define PF_DTRACE_OFF 1 | |
18 | #define PF_DTRACE_BIT 5 | |
19 | ||
0893f125 BS |
20 | /* |
21 | * NOTE! The single-stepping code assumes that all interrupt handlers | |
22 | * start by saving SYSCFG on the stack with their first instruction. | |
23 | */ | |
24 | ||
1394f032 BW |
25 | /* This one is used for exceptions, emulation, and NMI. It doesn't push |
26 | RETI and doesn't do cli. */ | |
27 | #define SAVE_ALL_SYS save_context_no_interrupts | |
28 | /* This is used for all normal interrupts. It saves a minimum of registers | |
29 | to the stack, loads the IRQ number, and jumps to common code. */ | |
6a01f230 YL |
30 | #ifdef CONFIG_IPIPE |
31 | # define LOAD_IPIPE_IPEND \ | |
32 | P0.l = lo(IPEND); \ | |
33 | P0.h = hi(IPEND); \ | |
34 | R1 = [P0]; | |
35 | #else | |
36 | # define LOAD_IPIPE_IPEND | |
37 | #endif | |
1394f032 BW |
38 | #define INTERRUPT_ENTRY(N) \ |
39 | [--sp] = SYSCFG; \ | |
40 | \ | |
41 | [--sp] = P0; /*orig_p0*/ \ | |
42 | [--sp] = R0; /*orig_r0*/ \ | |
43 | [--sp] = (R7:0,P5:0); \ | |
44 | R0 = (N); \ | |
6a01f230 | 45 | LOAD_IPIPE_IPEND \ |
1394f032 BW |
46 | jump __common_int_entry; |
47 | ||
48 | /* For timer interrupts, we need to save IPEND, since the user_mode | |
49 | macro accesses it to determine where to account time. */ | |
50 | #define TIMER_INTERRUPT_ENTRY(N) \ | |
51 | [--sp] = SYSCFG; \ | |
52 | \ | |
53 | [--sp] = P0; /*orig_p0*/ \ | |
54 | [--sp] = R0; /*orig_r0*/ \ | |
55 | [--sp] = (R7:0,P5:0); \ | |
56 | p0.l = lo(IPEND); \ | |
57 | p0.h = hi(IPEND); \ | |
58 | r1 = [p0]; \ | |
59 | R0 = (N); \ | |
60 | jump __common_int_entry; | |
61 | ||
62 | /* This one pushes RETI without using CLI. Interrupts are enabled. */ | |
63 | #define SAVE_CONTEXT_SYSCALL save_context_syscall | |
64 | #define SAVE_CONTEXT save_context_with_interrupts | |
dbdf20db | 65 | #define SAVE_CONTEXT_CPLB save_context_cplb |
1394f032 BW |
66 | |
67 | #define RESTORE_ALL_SYS restore_context_no_interrupts | |
68 | #define RESTORE_CONTEXT restore_context_with_interrupts | |
dbdf20db | 69 | #define RESTORE_CONTEXT_CPLB restore_context_cplb |
1394f032 BW |
70 | |
71 | #endif /* __ASSEMBLY__ */ | |
72 | #endif /* __BFIN_ENTRY_H */ |