]>
Commit | Line | Data |
---|---|---|
88358ab0 BH |
1 | /* |
2 | * Libata based driver for Apple "macio" family of PATA controllers | |
3 | * | |
4 | * Copyright 2008/2009 Benjamin Herrenschmidt, IBM Corp | |
5 | * <benh@kernel.crashing.org> | |
6 | * | |
7 | * Some bits and pieces from drivers/ide/ppc/pmac.c | |
8 | * | |
9 | */ | |
10 | ||
11 | #undef DEBUG | |
12 | #undef DEBUG_DMA | |
13 | ||
14 | #include <linux/kernel.h> | |
15 | #include <linux/module.h> | |
16 | #include <linux/init.h> | |
17 | #include <linux/blkdev.h> | |
18 | #include <linux/ata.h> | |
19 | #include <linux/libata.h> | |
20 | #include <linux/adb.h> | |
21 | #include <linux/pmu.h> | |
22 | #include <linux/scatterlist.h> | |
23 | #include <linux/of.h> | |
5a0e3ad6 | 24 | #include <linux/gfp.h> |
952bbcb0 | 25 | #include <linux/pci.h> |
88358ab0 BH |
26 | |
27 | #include <scsi/scsi.h> | |
28 | #include <scsi/scsi_host.h> | |
29 | #include <scsi/scsi_device.h> | |
30 | ||
31 | #include <asm/macio.h> | |
32 | #include <asm/io.h> | |
33 | #include <asm/dbdma.h> | |
88358ab0 BH |
34 | #include <asm/machdep.h> |
35 | #include <asm/pmac_feature.h> | |
36 | #include <asm/mediabay.h> | |
37 | ||
38 | #ifdef DEBUG_DMA | |
39 | #define dev_dbgdma(dev, format, arg...) \ | |
40 | dev_printk(KERN_DEBUG , dev , format , ## arg) | |
41 | #else | |
42 | #define dev_dbgdma(dev, format, arg...) \ | |
43 | ({ if (0) dev_printk(KERN_DEBUG, dev, format, ##arg); 0; }) | |
44 | #endif | |
45 | ||
46 | #define DRV_NAME "pata_macio" | |
47 | #define DRV_VERSION "0.9" | |
48 | ||
49 | /* Models of macio ATA controller */ | |
50 | enum { | |
51 | controller_ohare, /* OHare based */ | |
52 | controller_heathrow, /* Heathrow/Paddington */ | |
53 | controller_kl_ata3, /* KeyLargo ATA-3 */ | |
54 | controller_kl_ata4, /* KeyLargo ATA-4 */ | |
55 | controller_un_ata6, /* UniNorth2 ATA-6 */ | |
56 | controller_k2_ata6, /* K2 ATA-6 */ | |
57 | controller_sh_ata6, /* Shasta ATA-6 */ | |
58 | }; | |
59 | ||
60 | static const char* macio_ata_names[] = { | |
61 | "OHare ATA", /* OHare based */ | |
62 | "Heathrow ATA", /* Heathrow/Paddington */ | |
63 | "KeyLargo ATA-3", /* KeyLargo ATA-3 (MDMA only) */ | |
64 | "KeyLargo ATA-4", /* KeyLargo ATA-4 (UDMA/66) */ | |
65 | "UniNorth ATA-6", /* UniNorth2 ATA-6 (UDMA/100) */ | |
66 | "K2 ATA-6", /* K2 ATA-6 (UDMA/100) */ | |
67 | "Shasta ATA-6", /* Shasta ATA-6 (UDMA/133) */ | |
68 | }; | |
69 | ||
70 | /* | |
71 | * Extra registers, both 32-bit little-endian | |
72 | */ | |
73 | #define IDE_TIMING_CONFIG 0x200 | |
74 | #define IDE_INTERRUPT 0x300 | |
75 | ||
76 | /* Kauai (U2) ATA has different register setup */ | |
77 | #define IDE_KAUAI_PIO_CONFIG 0x200 | |
78 | #define IDE_KAUAI_ULTRA_CONFIG 0x210 | |
79 | #define IDE_KAUAI_POLL_CONFIG 0x220 | |
80 | ||
81 | /* | |
82 | * Timing configuration register definitions | |
83 | */ | |
84 | ||
85 | /* Number of IDE_SYSCLK_NS ticks, argument is in nanoseconds */ | |
86 | #define SYSCLK_TICKS(t) (((t) + IDE_SYSCLK_NS - 1) / IDE_SYSCLK_NS) | |
87 | #define SYSCLK_TICKS_66(t) (((t) + IDE_SYSCLK_66_NS - 1) / IDE_SYSCLK_66_NS) | |
88 | #define IDE_SYSCLK_NS 30 /* 33Mhz cell */ | |
89 | #define IDE_SYSCLK_66_NS 15 /* 66Mhz cell */ | |
90 | ||
91 | /* 133Mhz cell, found in shasta. | |
92 | * See comments about 100 Mhz Uninorth 2... | |
93 | * Note that PIO_MASK and MDMA_MASK seem to overlap, that's just | |
94 | * weird and I don't now why .. at this stage | |
95 | */ | |
96 | #define TR_133_PIOREG_PIO_MASK 0xff000fff | |
97 | #define TR_133_PIOREG_MDMA_MASK 0x00fff800 | |
98 | #define TR_133_UDMAREG_UDMA_MASK 0x0003ffff | |
99 | #define TR_133_UDMAREG_UDMA_EN 0x00000001 | |
100 | ||
101 | /* 100Mhz cell, found in Uninorth 2 and K2. It appears as a pci device | |
102 | * (106b/0033) on uninorth or K2 internal PCI bus and it's clock is | |
103 | * controlled like gem or fw. It appears to be an evolution of keylargo | |
104 | * ATA4 with a timing register extended to 2x32bits registers (one | |
105 | * for PIO & MWDMA and one for UDMA, and a similar DBDMA channel. | |
106 | * It has it's own local feature control register as well. | |
107 | * | |
108 | * After scratching my mind over the timing values, at least for PIO | |
109 | * and MDMA, I think I've figured the format of the timing register, | |
110 | * though I use pre-calculated tables for UDMA as usual... | |
111 | */ | |
112 | #define TR_100_PIO_ADDRSETUP_MASK 0xff000000 /* Size of field unknown */ | |
113 | #define TR_100_PIO_ADDRSETUP_SHIFT 24 | |
114 | #define TR_100_MDMA_MASK 0x00fff000 | |
115 | #define TR_100_MDMA_RECOVERY_MASK 0x00fc0000 | |
116 | #define TR_100_MDMA_RECOVERY_SHIFT 18 | |
117 | #define TR_100_MDMA_ACCESS_MASK 0x0003f000 | |
118 | #define TR_100_MDMA_ACCESS_SHIFT 12 | |
119 | #define TR_100_PIO_MASK 0xff000fff | |
120 | #define TR_100_PIO_RECOVERY_MASK 0x00000fc0 | |
121 | #define TR_100_PIO_RECOVERY_SHIFT 6 | |
122 | #define TR_100_PIO_ACCESS_MASK 0x0000003f | |
123 | #define TR_100_PIO_ACCESS_SHIFT 0 | |
124 | ||
125 | #define TR_100_UDMAREG_UDMA_MASK 0x0000ffff | |
126 | #define TR_100_UDMAREG_UDMA_EN 0x00000001 | |
127 | ||
128 | ||
129 | /* 66Mhz cell, found in KeyLargo. Can do ultra mode 0 to 2 on | |
130 | * 40 connector cable and to 4 on 80 connector one. | |
131 | * Clock unit is 15ns (66Mhz) | |
132 | * | |
133 | * 3 Values can be programmed: | |
134 | * - Write data setup, which appears to match the cycle time. They | |
135 | * also call it DIOW setup. | |
136 | * - Ready to pause time (from spec) | |
137 | * - Address setup. That one is weird. I don't see where exactly | |
138 | * it fits in UDMA cycles, I got it's name from an obscure piece | |
139 | * of commented out code in Darwin. They leave it to 0, we do as | |
140 | * well, despite a comment that would lead to think it has a | |
141 | * min value of 45ns. | |
142 | * Apple also add 60ns to the write data setup (or cycle time ?) on | |
143 | * reads. | |
144 | */ | |
145 | #define TR_66_UDMA_MASK 0xfff00000 | |
146 | #define TR_66_UDMA_EN 0x00100000 /* Enable Ultra mode for DMA */ | |
147 | #define TR_66_PIO_ADDRSETUP_MASK 0xe0000000 /* Address setup */ | |
148 | #define TR_66_PIO_ADDRSETUP_SHIFT 29 | |
149 | #define TR_66_UDMA_RDY2PAUS_MASK 0x1e000000 /* Ready 2 pause time */ | |
150 | #define TR_66_UDMA_RDY2PAUS_SHIFT 25 | |
151 | #define TR_66_UDMA_WRDATASETUP_MASK 0x01e00000 /* Write data setup time */ | |
152 | #define TR_66_UDMA_WRDATASETUP_SHIFT 21 | |
153 | #define TR_66_MDMA_MASK 0x000ffc00 | |
154 | #define TR_66_MDMA_RECOVERY_MASK 0x000f8000 | |
155 | #define TR_66_MDMA_RECOVERY_SHIFT 15 | |
156 | #define TR_66_MDMA_ACCESS_MASK 0x00007c00 | |
157 | #define TR_66_MDMA_ACCESS_SHIFT 10 | |
158 | #define TR_66_PIO_MASK 0xe00003ff | |
159 | #define TR_66_PIO_RECOVERY_MASK 0x000003e0 | |
160 | #define TR_66_PIO_RECOVERY_SHIFT 5 | |
161 | #define TR_66_PIO_ACCESS_MASK 0x0000001f | |
162 | #define TR_66_PIO_ACCESS_SHIFT 0 | |
163 | ||
164 | /* 33Mhz cell, found in OHare, Heathrow (& Paddington) and KeyLargo | |
165 | * Can do pio & mdma modes, clock unit is 30ns (33Mhz) | |
166 | * | |
167 | * The access time and recovery time can be programmed. Some older | |
168 | * Darwin code base limit OHare to 150ns cycle time. I decided to do | |
169 | * the same here fore safety against broken old hardware ;) | |
170 | * The HalfTick bit, when set, adds half a clock (15ns) to the access | |
171 | * time and removes one from recovery. It's not supported on KeyLargo | |
172 | * implementation afaik. The E bit appears to be set for PIO mode 0 and | |
173 | * is used to reach long timings used in this mode. | |
174 | */ | |
175 | #define TR_33_MDMA_MASK 0x003ff800 | |
176 | #define TR_33_MDMA_RECOVERY_MASK 0x001f0000 | |
177 | #define TR_33_MDMA_RECOVERY_SHIFT 16 | |
178 | #define TR_33_MDMA_ACCESS_MASK 0x0000f800 | |
179 | #define TR_33_MDMA_ACCESS_SHIFT 11 | |
180 | #define TR_33_MDMA_HALFTICK 0x00200000 | |
181 | #define TR_33_PIO_MASK 0x000007ff | |
182 | #define TR_33_PIO_E 0x00000400 | |
183 | #define TR_33_PIO_RECOVERY_MASK 0x000003e0 | |
184 | #define TR_33_PIO_RECOVERY_SHIFT 5 | |
185 | #define TR_33_PIO_ACCESS_MASK 0x0000001f | |
186 | #define TR_33_PIO_ACCESS_SHIFT 0 | |
187 | ||
188 | /* | |
189 | * Interrupt register definitions. Only present on newer cells | |
190 | * (Keylargo and later afaik) so we don't use it. | |
191 | */ | |
192 | #define IDE_INTR_DMA 0x80000000 | |
193 | #define IDE_INTR_DEVICE 0x40000000 | |
194 | ||
195 | /* | |
196 | * FCR Register on Kauai. Not sure what bit 0x4 is ... | |
197 | */ | |
198 | #define KAUAI_FCR_UATA_MAGIC 0x00000004 | |
199 | #define KAUAI_FCR_UATA_RESET_N 0x00000002 | |
200 | #define KAUAI_FCR_UATA_ENABLE 0x00000001 | |
201 | ||
202 | ||
203 | /* Allow up to 256 DBDMA commands per xfer */ | |
204 | #define MAX_DCMDS 256 | |
205 | ||
206 | /* Don't let a DMA segment go all the way to 64K */ | |
207 | #define MAX_DBDMA_SEG 0xff00 | |
208 | ||
209 | ||
210 | /* | |
211 | * Wait 1s for disk to answer on IDE bus after a hard reset | |
212 | * of the device (via GPIO/FCR). | |
213 | * | |
214 | * Some devices seem to "pollute" the bus even after dropping | |
215 | * the BSY bit (typically some combo drives slave on the UDMA | |
216 | * bus) after a hard reset. Since we hard reset all drives on | |
217 | * KeyLargo ATA66, we have to keep that delay around. I may end | |
218 | * up not hard resetting anymore on these and keep the delay only | |
219 | * for older interfaces instead (we have to reset when coming | |
220 | * from MacOS...) --BenH. | |
221 | */ | |
222 | #define IDE_WAKEUP_DELAY_MS 1000 | |
223 | ||
224 | struct pata_macio_timing; | |
225 | ||
226 | struct pata_macio_priv { | |
227 | int kind; | |
228 | int aapl_bus_id; | |
229 | int mediabay : 1; | |
230 | struct device_node *node; | |
231 | struct macio_dev *mdev; | |
232 | struct pci_dev *pdev; | |
233 | struct device *dev; | |
234 | int irq; | |
235 | u32 treg[2][2]; | |
236 | void __iomem *tfregs; | |
237 | void __iomem *kauai_fcr; | |
238 | struct dbdma_cmd * dma_table_cpu; | |
239 | dma_addr_t dma_table_dma; | |
240 | struct ata_host *host; | |
241 | const struct pata_macio_timing *timings; | |
242 | }; | |
243 | ||
244 | /* Previous variants of this driver used to calculate timings | |
245 | * for various variants of the chip and use tables for others. | |
246 | * | |
247 | * Not only was this confusing, but in addition, it isn't clear | |
248 | * whether our calculation code was correct. It didn't entirely | |
249 | * match the darwin code and whatever documentation I could find | |
250 | * on these cells | |
251 | * | |
252 | * I decided to entirely rely on a table instead for this version | |
253 | * of the driver. Also, because I don't really care about derated | |
254 | * modes and really old HW other than making it work, I'm not going | |
255 | * to calculate / snoop timing values for something else than the | |
256 | * standard modes. | |
257 | */ | |
258 | struct pata_macio_timing { | |
259 | int mode; | |
260 | u32 reg1; /* Bits to set in first timing reg */ | |
261 | u32 reg2; /* Bits to set in second timing reg */ | |
262 | }; | |
263 | ||
264 | static const struct pata_macio_timing pata_macio_ohare_timings[] = { | |
265 | { XFER_PIO_0, 0x00000526, 0, }, | |
266 | { XFER_PIO_1, 0x00000085, 0, }, | |
267 | { XFER_PIO_2, 0x00000025, 0, }, | |
268 | { XFER_PIO_3, 0x00000025, 0, }, | |
269 | { XFER_PIO_4, 0x00000025, 0, }, | |
270 | { XFER_MW_DMA_0, 0x00074000, 0, }, | |
271 | { XFER_MW_DMA_1, 0x00221000, 0, }, | |
272 | { XFER_MW_DMA_2, 0x00211000, 0, }, | |
273 | { -1, 0, 0 } | |
274 | }; | |
275 | ||
276 | static const struct pata_macio_timing pata_macio_heathrow_timings[] = { | |
277 | { XFER_PIO_0, 0x00000526, 0, }, | |
278 | { XFER_PIO_1, 0x00000085, 0, }, | |
279 | { XFER_PIO_2, 0x00000025, 0, }, | |
280 | { XFER_PIO_3, 0x00000025, 0, }, | |
281 | { XFER_PIO_4, 0x00000025, 0, }, | |
282 | { XFER_MW_DMA_0, 0x00074000, 0, }, | |
283 | { XFER_MW_DMA_1, 0x00221000, 0, }, | |
284 | { XFER_MW_DMA_2, 0x00211000, 0, }, | |
285 | { -1, 0, 0 } | |
286 | }; | |
287 | ||
288 | static const struct pata_macio_timing pata_macio_kl33_timings[] = { | |
289 | { XFER_PIO_0, 0x00000526, 0, }, | |
290 | { XFER_PIO_1, 0x00000085, 0, }, | |
291 | { XFER_PIO_2, 0x00000025, 0, }, | |
292 | { XFER_PIO_3, 0x00000025, 0, }, | |
293 | { XFER_PIO_4, 0x00000025, 0, }, | |
294 | { XFER_MW_DMA_0, 0x00084000, 0, }, | |
295 | { XFER_MW_DMA_1, 0x00021800, 0, }, | |
296 | { XFER_MW_DMA_2, 0x00011800, 0, }, | |
297 | { -1, 0, 0 } | |
298 | }; | |
299 | ||
300 | static const struct pata_macio_timing pata_macio_kl66_timings[] = { | |
301 | { XFER_PIO_0, 0x0000038c, 0, }, | |
302 | { XFER_PIO_1, 0x0000020a, 0, }, | |
303 | { XFER_PIO_2, 0x00000127, 0, }, | |
304 | { XFER_PIO_3, 0x000000c6, 0, }, | |
305 | { XFER_PIO_4, 0x00000065, 0, }, | |
306 | { XFER_MW_DMA_0, 0x00084000, 0, }, | |
307 | { XFER_MW_DMA_1, 0x00029800, 0, }, | |
308 | { XFER_MW_DMA_2, 0x00019400, 0, }, | |
309 | { XFER_UDMA_0, 0x19100000, 0, }, | |
310 | { XFER_UDMA_1, 0x14d00000, 0, }, | |
311 | { XFER_UDMA_2, 0x10900000, 0, }, | |
312 | { XFER_UDMA_3, 0x0c700000, 0, }, | |
313 | { XFER_UDMA_4, 0x0c500000, 0, }, | |
314 | { -1, 0, 0 } | |
315 | }; | |
316 | ||
317 | static const struct pata_macio_timing pata_macio_kauai_timings[] = { | |
318 | { XFER_PIO_0, 0x08000a92, 0, }, | |
319 | { XFER_PIO_1, 0x0800060f, 0, }, | |
320 | { XFER_PIO_2, 0x0800038b, 0, }, | |
321 | { XFER_PIO_3, 0x05000249, 0, }, | |
322 | { XFER_PIO_4, 0x04000148, 0, }, | |
323 | { XFER_MW_DMA_0, 0x00618000, 0, }, | |
324 | { XFER_MW_DMA_1, 0x00209000, 0, }, | |
325 | { XFER_MW_DMA_2, 0x00148000, 0, }, | |
326 | { XFER_UDMA_0, 0, 0x000070c1, }, | |
327 | { XFER_UDMA_1, 0, 0x00005d81, }, | |
328 | { XFER_UDMA_2, 0, 0x00004a61, }, | |
329 | { XFER_UDMA_3, 0, 0x00003a51, }, | |
330 | { XFER_UDMA_4, 0, 0x00002a31, }, | |
331 | { XFER_UDMA_5, 0, 0x00002921, }, | |
332 | { -1, 0, 0 } | |
333 | }; | |
334 | ||
335 | static const struct pata_macio_timing pata_macio_shasta_timings[] = { | |
336 | { XFER_PIO_0, 0x0a000c97, 0, }, | |
337 | { XFER_PIO_1, 0x07000712, 0, }, | |
338 | { XFER_PIO_2, 0x040003cd, 0, }, | |
339 | { XFER_PIO_3, 0x0500028b, 0, }, | |
340 | { XFER_PIO_4, 0x0400010a, 0, }, | |
341 | { XFER_MW_DMA_0, 0x00820800, 0, }, | |
342 | { XFER_MW_DMA_1, 0x0028b000, 0, }, | |
343 | { XFER_MW_DMA_2, 0x001ca000, 0, }, | |
344 | { XFER_UDMA_0, 0, 0x00035901, }, | |
345 | { XFER_UDMA_1, 0, 0x000348b1, }, | |
346 | { XFER_UDMA_2, 0, 0x00033881, }, | |
347 | { XFER_UDMA_3, 0, 0x00033861, }, | |
348 | { XFER_UDMA_4, 0, 0x00033841, }, | |
349 | { XFER_UDMA_5, 0, 0x00033031, }, | |
350 | { XFER_UDMA_6, 0, 0x00033021, }, | |
351 | { -1, 0, 0 } | |
352 | }; | |
353 | ||
354 | static const struct pata_macio_timing *pata_macio_find_timing( | |
355 | struct pata_macio_priv *priv, | |
356 | int mode) | |
357 | { | |
358 | int i; | |
359 | ||
360 | for (i = 0; priv->timings[i].mode > 0; i++) { | |
361 | if (priv->timings[i].mode == mode) | |
362 | return &priv->timings[i]; | |
363 | } | |
364 | return NULL; | |
365 | } | |
366 | ||
367 | ||
368 | static void pata_macio_apply_timings(struct ata_port *ap, unsigned int device) | |
369 | { | |
370 | struct pata_macio_priv *priv = ap->private_data; | |
371 | void __iomem *rbase = ap->ioaddr.cmd_addr; | |
372 | ||
373 | if (priv->kind == controller_sh_ata6 || | |
374 | priv->kind == controller_un_ata6 || | |
375 | priv->kind == controller_k2_ata6) { | |
376 | writel(priv->treg[device][0], rbase + IDE_KAUAI_PIO_CONFIG); | |
377 | writel(priv->treg[device][1], rbase + IDE_KAUAI_ULTRA_CONFIG); | |
378 | } else | |
379 | writel(priv->treg[device][0], rbase + IDE_TIMING_CONFIG); | |
380 | } | |
381 | ||
382 | static void pata_macio_dev_select(struct ata_port *ap, unsigned int device) | |
383 | { | |
384 | ata_sff_dev_select(ap, device); | |
385 | ||
386 | /* Apply timings */ | |
387 | pata_macio_apply_timings(ap, device); | |
388 | } | |
389 | ||
390 | static void pata_macio_set_timings(struct ata_port *ap, | |
391 | struct ata_device *adev) | |
392 | { | |
393 | struct pata_macio_priv *priv = ap->private_data; | |
394 | const struct pata_macio_timing *t; | |
395 | ||
396 | dev_dbg(priv->dev, "Set timings: DEV=%d,PIO=0x%x (%s),DMA=0x%x (%s)\n", | |
397 | adev->devno, | |
398 | adev->pio_mode, | |
399 | ata_mode_string(ata_xfer_mode2mask(adev->pio_mode)), | |
400 | adev->dma_mode, | |
401 | ata_mode_string(ata_xfer_mode2mask(adev->dma_mode))); | |
402 | ||
403 | /* First clear timings */ | |
404 | priv->treg[adev->devno][0] = priv->treg[adev->devno][1] = 0; | |
405 | ||
406 | /* Now get the PIO timings */ | |
407 | t = pata_macio_find_timing(priv, adev->pio_mode); | |
408 | if (t == NULL) { | |
409 | dev_warn(priv->dev, "Invalid PIO timing requested: 0x%x\n", | |
410 | adev->pio_mode); | |
411 | t = pata_macio_find_timing(priv, XFER_PIO_0); | |
412 | } | |
413 | BUG_ON(t == NULL); | |
414 | ||
415 | /* PIO timings only ever use the first treg */ | |
416 | priv->treg[adev->devno][0] |= t->reg1; | |
417 | ||
418 | /* Now get DMA timings */ | |
419 | t = pata_macio_find_timing(priv, adev->dma_mode); | |
420 | if (t == NULL || (t->reg1 == 0 && t->reg2 == 0)) { | |
421 | dev_dbg(priv->dev, "DMA timing not set yet, using MW_DMA_0\n"); | |
422 | t = pata_macio_find_timing(priv, XFER_MW_DMA_0); | |
423 | } | |
424 | BUG_ON(t == NULL); | |
425 | ||
426 | /* DMA timings can use both tregs */ | |
427 | priv->treg[adev->devno][0] |= t->reg1; | |
428 | priv->treg[adev->devno][1] |= t->reg2; | |
429 | ||
430 | dev_dbg(priv->dev, " -> %08x %08x\n", | |
431 | priv->treg[adev->devno][0], | |
432 | priv->treg[adev->devno][1]); | |
433 | ||
434 | /* Apply to hardware */ | |
435 | pata_macio_apply_timings(ap, adev->devno); | |
436 | } | |
437 | ||
438 | /* | |
439 | * Blast some well known "safe" values to the timing registers at init or | |
440 | * wakeup from sleep time, before we do real calculation | |
441 | */ | |
442 | static void pata_macio_default_timings(struct pata_macio_priv *priv) | |
443 | { | |
444 | unsigned int value, value2 = 0; | |
445 | ||
446 | switch(priv->kind) { | |
447 | case controller_sh_ata6: | |
448 | value = 0x0a820c97; | |
449 | value2 = 0x00033031; | |
450 | break; | |
451 | case controller_un_ata6: | |
452 | case controller_k2_ata6: | |
453 | value = 0x08618a92; | |
454 | value2 = 0x00002921; | |
455 | break; | |
456 | case controller_kl_ata4: | |
457 | value = 0x0008438c; | |
458 | break; | |
459 | case controller_kl_ata3: | |
460 | value = 0x00084526; | |
461 | break; | |
462 | case controller_heathrow: | |
463 | case controller_ohare: | |
464 | default: | |
465 | value = 0x00074526; | |
466 | break; | |
467 | } | |
468 | priv->treg[0][0] = priv->treg[1][0] = value; | |
469 | priv->treg[0][1] = priv->treg[1][1] = value2; | |
470 | } | |
471 | ||
472 | static int pata_macio_cable_detect(struct ata_port *ap) | |
473 | { | |
474 | struct pata_macio_priv *priv = ap->private_data; | |
475 | ||
476 | /* Get cable type from device-tree */ | |
477 | if (priv->kind == controller_kl_ata4 || | |
478 | priv->kind == controller_un_ata6 || | |
479 | priv->kind == controller_k2_ata6 || | |
480 | priv->kind == controller_sh_ata6) { | |
481 | const char* cable = of_get_property(priv->node, "cable-type", | |
482 | NULL); | |
483 | struct device_node *root = of_find_node_by_path("/"); | |
484 | const char *model = of_get_property(root, "model", NULL); | |
485 | ||
745d51dc YL |
486 | of_node_put(root); |
487 | ||
88358ab0 BH |
488 | if (cable && !strncmp(cable, "80-", 3)) { |
489 | /* Some drives fail to detect 80c cable in PowerBook | |
490 | * These machine use proprietary short IDE cable | |
491 | * anyway | |
492 | */ | |
493 | if (!strncmp(model, "PowerBook", 9)) | |
494 | return ATA_CBL_PATA40_SHORT; | |
495 | else | |
496 | return ATA_CBL_PATA80; | |
497 | } | |
498 | } | |
499 | ||
500 | /* G5's seem to have incorrect cable type in device-tree. | |
501 | * Let's assume they always have a 80 conductor cable, this seem to | |
502 | * be always the case unless the user mucked around | |
503 | */ | |
504 | if (of_device_is_compatible(priv->node, "K2-UATA") || | |
505 | of_device_is_compatible(priv->node, "shasta-ata")) | |
506 | return ATA_CBL_PATA80; | |
507 | ||
508 | /* Anything else is 40 connectors */ | |
509 | return ATA_CBL_PATA40; | |
510 | } | |
511 | ||
512 | static void pata_macio_qc_prep(struct ata_queued_cmd *qc) | |
513 | { | |
514 | unsigned int write = (qc->tf.flags & ATA_TFLAG_WRITE); | |
515 | struct ata_port *ap = qc->ap; | |
516 | struct pata_macio_priv *priv = ap->private_data; | |
517 | struct scatterlist *sg; | |
518 | struct dbdma_cmd *table; | |
519 | unsigned int si, pi; | |
520 | ||
521 | dev_dbgdma(priv->dev, "%s: qc %p flags %lx, write %d dev %d\n", | |
522 | __func__, qc, qc->flags, write, qc->dev->devno); | |
523 | ||
524 | if (!(qc->flags & ATA_QCFLAG_DMAMAP)) | |
525 | return; | |
526 | ||
527 | table = (struct dbdma_cmd *) priv->dma_table_cpu; | |
528 | ||
529 | pi = 0; | |
530 | for_each_sg(qc->sg, sg, qc->n_elem, si) { | |
531 | u32 addr, sg_len, len; | |
532 | ||
533 | /* determine if physical DMA addr spans 64K boundary. | |
534 | * Note h/w doesn't support 64-bit, so we unconditionally | |
535 | * truncate dma_addr_t to u32. | |
536 | */ | |
537 | addr = (u32) sg_dma_address(sg); | |
538 | sg_len = sg_dma_len(sg); | |
539 | ||
540 | while (sg_len) { | |
541 | /* table overflow should never happen */ | |
542 | BUG_ON (pi++ >= MAX_DCMDS); | |
543 | ||
544 | len = (sg_len < MAX_DBDMA_SEG) ? sg_len : MAX_DBDMA_SEG; | |
f5718726 DG |
545 | table->command = cpu_to_le16(write ? OUTPUT_MORE: INPUT_MORE); |
546 | table->req_count = cpu_to_le16(len); | |
547 | table->phy_addr = cpu_to_le32(addr); | |
88358ab0 BH |
548 | table->cmd_dep = 0; |
549 | table->xfer_status = 0; | |
550 | table->res_count = 0; | |
551 | addr += len; | |
552 | sg_len -= len; | |
553 | ++table; | |
554 | } | |
555 | } | |
556 | ||
557 | /* Should never happen according to Tejun */ | |
558 | BUG_ON(!pi); | |
559 | ||
560 | /* Convert the last command to an input/output */ | |
561 | table--; | |
f5718726 | 562 | table->command = cpu_to_le16(write ? OUTPUT_LAST: INPUT_LAST); |
88358ab0 BH |
563 | table++; |
564 | ||
565 | /* Add the stop command to the end of the list */ | |
566 | memset(table, 0, sizeof(struct dbdma_cmd)); | |
f5718726 | 567 | table->command = cpu_to_le16(DBDMA_STOP); |
88358ab0 BH |
568 | |
569 | dev_dbgdma(priv->dev, "%s: %d DMA list entries\n", __func__, pi); | |
570 | } | |
571 | ||
572 | ||
573 | static void pata_macio_freeze(struct ata_port *ap) | |
574 | { | |
575 | struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr; | |
576 | ||
577 | if (dma_regs) { | |
578 | unsigned int timeout = 1000000; | |
579 | ||
580 | /* Make sure DMA controller is stopped */ | |
581 | writel((RUN|PAUSE|FLUSH|WAKE|DEAD) << 16, &dma_regs->control); | |
582 | while (--timeout && (readl(&dma_regs->status) & RUN)) | |
583 | udelay(1); | |
584 | } | |
585 | ||
586 | ata_sff_freeze(ap); | |
587 | } | |
588 | ||
589 | ||
590 | static void pata_macio_bmdma_setup(struct ata_queued_cmd *qc) | |
591 | { | |
592 | struct ata_port *ap = qc->ap; | |
593 | struct pata_macio_priv *priv = ap->private_data; | |
594 | struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr; | |
595 | int dev = qc->dev->devno; | |
596 | ||
597 | dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc); | |
598 | ||
599 | /* Make sure DMA commands updates are visible */ | |
600 | writel(priv->dma_table_dma, &dma_regs->cmdptr); | |
601 | ||
602 | /* On KeyLargo 66Mhz cell, we need to add 60ns to wrDataSetup on | |
603 | * UDMA reads | |
604 | */ | |
605 | if (priv->kind == controller_kl_ata4 && | |
606 | (priv->treg[dev][0] & TR_66_UDMA_EN)) { | |
607 | void __iomem *rbase = ap->ioaddr.cmd_addr; | |
608 | u32 reg = priv->treg[dev][0]; | |
609 | ||
610 | if (!(qc->tf.flags & ATA_TFLAG_WRITE)) | |
611 | reg += 0x00800000; | |
612 | writel(reg, rbase + IDE_TIMING_CONFIG); | |
613 | } | |
614 | ||
615 | /* issue r/w command */ | |
616 | ap->ops->sff_exec_command(ap, &qc->tf); | |
617 | } | |
618 | ||
619 | static void pata_macio_bmdma_start(struct ata_queued_cmd *qc) | |
620 | { | |
621 | struct ata_port *ap = qc->ap; | |
622 | struct pata_macio_priv *priv = ap->private_data; | |
623 | struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr; | |
624 | ||
625 | dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc); | |
626 | ||
627 | writel((RUN << 16) | RUN, &dma_regs->control); | |
628 | /* Make sure it gets to the controller right now */ | |
629 | (void)readl(&dma_regs->control); | |
630 | } | |
631 | ||
632 | static void pata_macio_bmdma_stop(struct ata_queued_cmd *qc) | |
633 | { | |
634 | struct ata_port *ap = qc->ap; | |
635 | struct pata_macio_priv *priv = ap->private_data; | |
636 | struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr; | |
637 | unsigned int timeout = 1000000; | |
638 | ||
639 | dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc); | |
640 | ||
641 | /* Stop the DMA engine and wait for it to full halt */ | |
642 | writel (((RUN|WAKE|DEAD) << 16), &dma_regs->control); | |
643 | while (--timeout && (readl(&dma_regs->status) & RUN)) | |
644 | udelay(1); | |
645 | } | |
646 | ||
647 | static u8 pata_macio_bmdma_status(struct ata_port *ap) | |
648 | { | |
649 | struct pata_macio_priv *priv = ap->private_data; | |
650 | struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr; | |
651 | u32 dstat, rstat = ATA_DMA_INTR; | |
652 | unsigned long timeout = 0; | |
653 | ||
654 | dstat = readl(&dma_regs->status); | |
655 | ||
656 | dev_dbgdma(priv->dev, "%s: dstat=%x\n", __func__, dstat); | |
657 | ||
658 | /* We have two things to deal with here: | |
659 | * | |
660 | * - The dbdma won't stop if the command was started | |
661 | * but completed with an error without transferring all | |
662 | * datas. This happens when bad blocks are met during | |
663 | * a multi-block transfer. | |
664 | * | |
665 | * - The dbdma fifo hasn't yet finished flushing to | |
666 | * to system memory when the disk interrupt occurs. | |
667 | * | |
668 | */ | |
669 | ||
670 | /* First check for errors */ | |
671 | if ((dstat & (RUN|DEAD)) != RUN) | |
672 | rstat |= ATA_DMA_ERR; | |
673 | ||
674 | /* If ACTIVE is cleared, the STOP command has been hit and | |
675 | * the transfer is complete. If not, we have to flush the | |
676 | * channel. | |
677 | */ | |
678 | if ((dstat & ACTIVE) == 0) | |
679 | return rstat; | |
680 | ||
681 | dev_dbgdma(priv->dev, "%s: DMA still active, flushing...\n", __func__); | |
682 | ||
683 | /* If dbdma didn't execute the STOP command yet, the | |
684 | * active bit is still set. We consider that we aren't | |
685 | * sharing interrupts (which is hopefully the case with | |
686 | * those controllers) and so we just try to flush the | |
687 | * channel for pending data in the fifo | |
688 | */ | |
689 | udelay(1); | |
690 | writel((FLUSH << 16) | FLUSH, &dma_regs->control); | |
691 | for (;;) { | |
692 | udelay(1); | |
693 | dstat = readl(&dma_regs->status); | |
694 | if ((dstat & FLUSH) == 0) | |
695 | break; | |
696 | if (++timeout > 1000) { | |
697 | dev_warn(priv->dev, "timeout flushing DMA\n"); | |
698 | rstat |= ATA_DMA_ERR; | |
699 | break; | |
700 | } | |
701 | } | |
702 | return rstat; | |
703 | } | |
704 | ||
705 | /* port_start is when we allocate the DMA command list */ | |
706 | static int pata_macio_port_start(struct ata_port *ap) | |
707 | { | |
708 | struct pata_macio_priv *priv = ap->private_data; | |
709 | ||
710 | if (ap->ioaddr.bmdma_addr == NULL) | |
711 | return 0; | |
712 | ||
713 | /* Allocate space for the DBDMA commands. | |
714 | * | |
715 | * The +2 is +1 for the stop command and +1 to allow for | |
716 | * aligning the start address to a multiple of 16 bytes. | |
717 | */ | |
718 | priv->dma_table_cpu = | |
719 | dmam_alloc_coherent(priv->dev, | |
720 | (MAX_DCMDS + 2) * sizeof(struct dbdma_cmd), | |
721 | &priv->dma_table_dma, GFP_KERNEL); | |
722 | if (priv->dma_table_cpu == NULL) { | |
723 | dev_err(priv->dev, "Unable to allocate DMA command list\n"); | |
724 | ap->ioaddr.bmdma_addr = NULL; | |
c7087652 TH |
725 | ap->mwdma_mask = 0; |
726 | ap->udma_mask = 0; | |
88358ab0 BH |
727 | } |
728 | return 0; | |
729 | } | |
730 | ||
731 | static void pata_macio_irq_clear(struct ata_port *ap) | |
732 | { | |
733 | struct pata_macio_priv *priv = ap->private_data; | |
734 | ||
735 | /* Nothing to do here */ | |
736 | ||
737 | dev_dbgdma(priv->dev, "%s\n", __func__); | |
738 | } | |
739 | ||
740 | static void pata_macio_reset_hw(struct pata_macio_priv *priv, int resume) | |
741 | { | |
742 | dev_dbg(priv->dev, "Enabling & resetting... \n"); | |
743 | ||
744 | if (priv->mediabay) | |
745 | return; | |
746 | ||
747 | if (priv->kind == controller_ohare && !resume) { | |
748 | /* The code below is having trouble on some ohare machines | |
749 | * (timing related ?). Until I can put my hand on one of these | |
750 | * units, I keep the old way | |
751 | */ | |
752 | ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node, 0, 1); | |
753 | } else { | |
754 | int rc; | |
755 | ||
756 | /* Reset and enable controller */ | |
757 | rc = ppc_md.feature_call(PMAC_FTR_IDE_RESET, | |
758 | priv->node, priv->aapl_bus_id, 1); | |
759 | ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, | |
760 | priv->node, priv->aapl_bus_id, 1); | |
761 | msleep(10); | |
762 | /* Only bother waiting if there's a reset control */ | |
763 | if (rc == 0) { | |
764 | ppc_md.feature_call(PMAC_FTR_IDE_RESET, | |
765 | priv->node, priv->aapl_bus_id, 0); | |
766 | msleep(IDE_WAKEUP_DELAY_MS); | |
767 | } | |
768 | } | |
769 | ||
770 | /* If resuming a PCI device, restore the config space here */ | |
771 | if (priv->pdev && resume) { | |
772 | int rc; | |
773 | ||
774 | pci_restore_state(priv->pdev); | |
775 | rc = pcim_enable_device(priv->pdev); | |
776 | if (rc) | |
a44fec1f JP |
777 | dev_err(&priv->pdev->dev, |
778 | "Failed to enable device after resume (%d)\n", | |
779 | rc); | |
88358ab0 BH |
780 | else |
781 | pci_set_master(priv->pdev); | |
782 | } | |
783 | ||
784 | /* On Kauai, initialize the FCR. We don't perform a reset, doesn't really | |
785 | * seem necessary and speeds up the boot process | |
786 | */ | |
787 | if (priv->kauai_fcr) | |
788 | writel(KAUAI_FCR_UATA_MAGIC | | |
789 | KAUAI_FCR_UATA_RESET_N | | |
790 | KAUAI_FCR_UATA_ENABLE, priv->kauai_fcr); | |
791 | } | |
792 | ||
793 | /* Hook the standard slave config to fixup some HW related alignment | |
794 | * restrictions | |
795 | */ | |
796 | static int pata_macio_slave_config(struct scsi_device *sdev) | |
797 | { | |
798 | struct ata_port *ap = ata_shost_to_port(sdev->host); | |
799 | struct pata_macio_priv *priv = ap->private_data; | |
800 | struct ata_device *dev; | |
801 | u16 cmd; | |
802 | int rc; | |
803 | ||
804 | /* First call original */ | |
805 | rc = ata_scsi_slave_config(sdev); | |
806 | if (rc) | |
807 | return rc; | |
808 | ||
809 | /* This is lifted from sata_nv */ | |
810 | dev = &ap->link.device[sdev->id]; | |
811 | ||
812 | /* OHare has issues with non cache aligned DMA on some chipsets */ | |
813 | if (priv->kind == controller_ohare) { | |
814 | blk_queue_update_dma_alignment(sdev->request_queue, 31); | |
815 | blk_queue_update_dma_pad(sdev->request_queue, 31); | |
816 | ||
817 | /* Tell the world about it */ | |
a9a79dfe | 818 | ata_dev_info(dev, "OHare alignment limits applied\n"); |
88358ab0 BH |
819 | return 0; |
820 | } | |
821 | ||
822 | /* We only have issues with ATAPI */ | |
823 | if (dev->class != ATA_DEV_ATAPI) | |
824 | return 0; | |
825 | ||
826 | /* Shasta and K2 seem to have "issues" with reads ... */ | |
827 | if (priv->kind == controller_sh_ata6 || priv->kind == controller_k2_ata6) { | |
828 | /* Allright these are bad, apply restrictions */ | |
829 | blk_queue_update_dma_alignment(sdev->request_queue, 15); | |
830 | blk_queue_update_dma_pad(sdev->request_queue, 15); | |
831 | ||
832 | /* We enable MWI and hack cache line size directly here, this | |
833 | * is specific to this chipset and not normal values, we happen | |
834 | * to somewhat know what we are doing here (which is basically | |
835 | * to do the same Apple does and pray they did not get it wrong :-) | |
836 | */ | |
837 | BUG_ON(!priv->pdev); | |
838 | pci_write_config_byte(priv->pdev, PCI_CACHE_LINE_SIZE, 0x08); | |
839 | pci_read_config_word(priv->pdev, PCI_COMMAND, &cmd); | |
840 | pci_write_config_word(priv->pdev, PCI_COMMAND, | |
841 | cmd | PCI_COMMAND_INVALIDATE); | |
842 | ||
843 | /* Tell the world about it */ | |
a9a79dfe | 844 | ata_dev_info(dev, "K2/Shasta alignment limits applied\n"); |
88358ab0 BH |
845 | } |
846 | ||
847 | return 0; | |
848 | } | |
849 | ||
58eb8cd5 | 850 | #ifdef CONFIG_PM_SLEEP |
88358ab0 BH |
851 | static int pata_macio_do_suspend(struct pata_macio_priv *priv, pm_message_t mesg) |
852 | { | |
853 | int rc; | |
854 | ||
855 | /* First, core libata suspend to do most of the work */ | |
856 | rc = ata_host_suspend(priv->host, mesg); | |
857 | if (rc) | |
858 | return rc; | |
859 | ||
860 | /* Restore to default timings */ | |
861 | pata_macio_default_timings(priv); | |
862 | ||
863 | /* Mask interrupt. Not strictly necessary but old driver did | |
864 | * it and I'd rather not change that here */ | |
865 | disable_irq(priv->irq); | |
866 | ||
867 | /* The media bay will handle itself just fine */ | |
868 | if (priv->mediabay) | |
869 | return 0; | |
870 | ||
871 | /* Kauai has bus control FCRs directly here */ | |
872 | if (priv->kauai_fcr) { | |
873 | u32 fcr = readl(priv->kauai_fcr); | |
874 | fcr &= ~(KAUAI_FCR_UATA_RESET_N | KAUAI_FCR_UATA_ENABLE); | |
875 | writel(fcr, priv->kauai_fcr); | |
876 | } | |
877 | ||
878 | /* For PCI, save state and disable DMA. No need to call | |
879 | * pci_set_power_state(), the HW doesn't do D states that | |
880 | * way, the platform code will take care of suspending the | |
881 | * ASIC properly | |
882 | */ | |
883 | if (priv->pdev) { | |
884 | pci_save_state(priv->pdev); | |
885 | pci_disable_device(priv->pdev); | |
886 | } | |
887 | ||
888 | /* Disable the bus on older machines and the cell on kauai */ | |
889 | ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node, | |
890 | priv->aapl_bus_id, 0); | |
891 | ||
892 | return 0; | |
893 | } | |
894 | ||
895 | static int pata_macio_do_resume(struct pata_macio_priv *priv) | |
896 | { | |
897 | /* Reset and re-enable the HW */ | |
898 | pata_macio_reset_hw(priv, 1); | |
899 | ||
900 | /* Sanitize drive timings */ | |
901 | pata_macio_apply_timings(priv->host->ports[0], 0); | |
902 | ||
903 | /* We want our IRQ back ! */ | |
904 | enable_irq(priv->irq); | |
905 | ||
906 | /* Let the libata core take it from there */ | |
907 | ata_host_resume(priv->host); | |
908 | ||
909 | return 0; | |
910 | } | |
58eb8cd5 | 911 | #endif /* CONFIG_PM_SLEEP */ |
88358ab0 BH |
912 | |
913 | static struct scsi_host_template pata_macio_sht = { | |
914 | ATA_BASE_SHT(DRV_NAME), | |
915 | .sg_tablesize = MAX_DCMDS, | |
916 | /* We may not need that strict one */ | |
917 | .dma_boundary = ATA_DMA_BOUNDARY, | |
a8cf59a6 CH |
918 | /* Not sure what the real max is but we know it's less than 64K, let's |
919 | * use 64K minus 256 | |
920 | */ | |
921 | .max_segment_size = MAX_DBDMA_SEG, | |
88358ab0 BH |
922 | .slave_configure = pata_macio_slave_config, |
923 | }; | |
924 | ||
925 | static struct ata_port_operations pata_macio_ops = { | |
8930ff25 | 926 | .inherits = &ata_bmdma_port_ops, |
88358ab0 BH |
927 | |
928 | .freeze = pata_macio_freeze, | |
929 | .set_piomode = pata_macio_set_timings, | |
930 | .set_dmamode = pata_macio_set_timings, | |
931 | .cable_detect = pata_macio_cable_detect, | |
932 | .sff_dev_select = pata_macio_dev_select, | |
933 | .qc_prep = pata_macio_qc_prep, | |
88358ab0 BH |
934 | .bmdma_setup = pata_macio_bmdma_setup, |
935 | .bmdma_start = pata_macio_bmdma_start, | |
936 | .bmdma_stop = pata_macio_bmdma_stop, | |
937 | .bmdma_status = pata_macio_bmdma_status, | |
938 | .port_start = pata_macio_port_start, | |
939 | .sff_irq_clear = pata_macio_irq_clear, | |
940 | }; | |
941 | ||
0ec24914 | 942 | static void pata_macio_invariants(struct pata_macio_priv *priv) |
88358ab0 BH |
943 | { |
944 | const int *bidp; | |
945 | ||
946 | /* Identify the type of controller */ | |
947 | if (of_device_is_compatible(priv->node, "shasta-ata")) { | |
948 | priv->kind = controller_sh_ata6; | |
949 | priv->timings = pata_macio_shasta_timings; | |
950 | } else if (of_device_is_compatible(priv->node, "kauai-ata")) { | |
951 | priv->kind = controller_un_ata6; | |
952 | priv->timings = pata_macio_kauai_timings; | |
953 | } else if (of_device_is_compatible(priv->node, "K2-UATA")) { | |
954 | priv->kind = controller_k2_ata6; | |
955 | priv->timings = pata_macio_kauai_timings; | |
956 | } else if (of_device_is_compatible(priv->node, "keylargo-ata")) { | |
957 | if (strcmp(priv->node->name, "ata-4") == 0) { | |
958 | priv->kind = controller_kl_ata4; | |
959 | priv->timings = pata_macio_kl66_timings; | |
960 | } else { | |
961 | priv->kind = controller_kl_ata3; | |
962 | priv->timings = pata_macio_kl33_timings; | |
963 | } | |
964 | } else if (of_device_is_compatible(priv->node, "heathrow-ata")) { | |
965 | priv->kind = controller_heathrow; | |
966 | priv->timings = pata_macio_heathrow_timings; | |
967 | } else { | |
968 | priv->kind = controller_ohare; | |
969 | priv->timings = pata_macio_ohare_timings; | |
970 | } | |
971 | ||
972 | /* XXX FIXME --- setup priv->mediabay here */ | |
973 | ||
974 | /* Get Apple bus ID (for clock and ASIC control) */ | |
975 | bidp = of_get_property(priv->node, "AAPL,bus-id", NULL); | |
976 | priv->aapl_bus_id = bidp ? *bidp : 0; | |
977 | ||
978 | /* Fixup missing Apple bus ID in case of media-bay */ | |
979 | if (priv->mediabay && bidp == 0) | |
980 | priv->aapl_bus_id = 1; | |
981 | } | |
982 | ||
0ec24914 GKH |
983 | static void pata_macio_setup_ios(struct ata_ioports *ioaddr, |
984 | void __iomem * base, void __iomem * dma) | |
88358ab0 BH |
985 | { |
986 | /* cmd_addr is the base of regs for that port */ | |
987 | ioaddr->cmd_addr = base; | |
988 | ||
989 | /* taskfile registers */ | |
990 | ioaddr->data_addr = base + (ATA_REG_DATA << 4); | |
991 | ioaddr->error_addr = base + (ATA_REG_ERR << 4); | |
992 | ioaddr->feature_addr = base + (ATA_REG_FEATURE << 4); | |
993 | ioaddr->nsect_addr = base + (ATA_REG_NSECT << 4); | |
994 | ioaddr->lbal_addr = base + (ATA_REG_LBAL << 4); | |
995 | ioaddr->lbam_addr = base + (ATA_REG_LBAM << 4); | |
996 | ioaddr->lbah_addr = base + (ATA_REG_LBAH << 4); | |
997 | ioaddr->device_addr = base + (ATA_REG_DEVICE << 4); | |
998 | ioaddr->status_addr = base + (ATA_REG_STATUS << 4); | |
999 | ioaddr->command_addr = base + (ATA_REG_CMD << 4); | |
1000 | ioaddr->altstatus_addr = base + 0x160; | |
1001 | ioaddr->ctl_addr = base + 0x160; | |
1002 | ioaddr->bmdma_addr = dma; | |
1003 | } | |
1004 | ||
0ec24914 GKH |
1005 | static void pmac_macio_calc_timing_masks(struct pata_macio_priv *priv, |
1006 | struct ata_port_info *pinfo) | |
88358ab0 BH |
1007 | { |
1008 | int i = 0; | |
1009 | ||
1010 | pinfo->pio_mask = 0; | |
1011 | pinfo->mwdma_mask = 0; | |
1012 | pinfo->udma_mask = 0; | |
1013 | ||
1014 | while (priv->timings[i].mode > 0) { | |
1015 | unsigned int mask = 1U << (priv->timings[i].mode & 0x0f); | |
1016 | switch(priv->timings[i].mode & 0xf0) { | |
1017 | case 0x00: /* PIO */ | |
1018 | pinfo->pio_mask |= (mask >> 8); | |
1019 | break; | |
1020 | case 0x20: /* MWDMA */ | |
1021 | pinfo->mwdma_mask |= mask; | |
1022 | break; | |
1023 | case 0x40: /* UDMA */ | |
1024 | pinfo->udma_mask |= mask; | |
1025 | break; | |
1026 | } | |
1027 | i++; | |
1028 | } | |
1029 | dev_dbg(priv->dev, "Supported masks: PIO=%lx, MWDMA=%lx, UDMA=%lx\n", | |
1030 | pinfo->pio_mask, pinfo->mwdma_mask, pinfo->udma_mask); | |
1031 | } | |
1032 | ||
0ec24914 GKH |
1033 | static int pata_macio_common_init(struct pata_macio_priv *priv, |
1034 | resource_size_t tfregs, | |
1035 | resource_size_t dmaregs, | |
1036 | resource_size_t fcregs, | |
1037 | unsigned long irq) | |
88358ab0 BH |
1038 | { |
1039 | struct ata_port_info pinfo; | |
1040 | const struct ata_port_info *ppi[] = { &pinfo, NULL }; | |
1041 | void __iomem *dma_regs = NULL; | |
1042 | ||
1043 | /* Fill up privates with various invariants collected from the | |
1044 | * device-tree | |
1045 | */ | |
1046 | pata_macio_invariants(priv); | |
1047 | ||
1048 | /* Make sure we have sane initial timings in the cache */ | |
1049 | pata_macio_default_timings(priv); | |
1050 | ||
88358ab0 BH |
1051 | /* Allocate libata host for 1 port */ |
1052 | memset(&pinfo, 0, sizeof(struct ata_port_info)); | |
1053 | pmac_macio_calc_timing_masks(priv, &pinfo); | |
9cbe056f | 1054 | pinfo.flags = ATA_FLAG_SLAVE_POSS; |
88358ab0 BH |
1055 | pinfo.port_ops = &pata_macio_ops; |
1056 | pinfo.private_data = priv; | |
1057 | ||
1058 | priv->host = ata_host_alloc_pinfo(priv->dev, ppi, 1); | |
1059 | if (priv->host == NULL) { | |
1060 | dev_err(priv->dev, "Failed to allocate ATA port structure\n"); | |
1061 | return -ENOMEM; | |
1062 | } | |
1063 | ||
1064 | /* Setup the private data in host too */ | |
1065 | priv->host->private_data = priv; | |
1066 | ||
1067 | /* Map base registers */ | |
1068 | priv->tfregs = devm_ioremap(priv->dev, tfregs, 0x100); | |
1069 | if (priv->tfregs == NULL) { | |
1070 | dev_err(priv->dev, "Failed to map ATA ports\n"); | |
1071 | return -ENOMEM; | |
1072 | } | |
1073 | priv->host->iomap = &priv->tfregs; | |
1074 | ||
1075 | /* Map DMA regs */ | |
1076 | if (dmaregs != 0) { | |
1077 | dma_regs = devm_ioremap(priv->dev, dmaregs, | |
1078 | sizeof(struct dbdma_regs)); | |
1079 | if (dma_regs == NULL) | |
1080 | dev_warn(priv->dev, "Failed to map ATA DMA registers\n"); | |
1081 | } | |
1082 | ||
1083 | /* If chip has local feature control, map those regs too */ | |
1084 | if (fcregs != 0) { | |
1085 | priv->kauai_fcr = devm_ioremap(priv->dev, fcregs, 4); | |
1086 | if (priv->kauai_fcr == NULL) { | |
1087 | dev_err(priv->dev, "Failed to map ATA FCR register\n"); | |
1088 | return -ENOMEM; | |
1089 | } | |
1090 | } | |
1091 | ||
1092 | /* Setup port data structure */ | |
1093 | pata_macio_setup_ios(&priv->host->ports[0]->ioaddr, | |
1094 | priv->tfregs, dma_regs); | |
1095 | priv->host->ports[0]->private_data = priv; | |
1096 | ||
1097 | /* hard-reset the controller */ | |
1098 | pata_macio_reset_hw(priv, 0); | |
1099 | pata_macio_apply_timings(priv->host->ports[0], 0); | |
1100 | ||
1101 | /* Enable bus master if necessary */ | |
1102 | if (priv->pdev && dma_regs) | |
1103 | pci_set_master(priv->pdev); | |
1104 | ||
1105 | dev_info(priv->dev, "Activating pata-macio chipset %s, Apple bus ID %d\n", | |
1106 | macio_ata_names[priv->kind], priv->aapl_bus_id); | |
1107 | ||
1108 | /* Start it up */ | |
1109 | priv->irq = irq; | |
c3b28894 | 1110 | return ata_host_activate(priv->host, irq, ata_bmdma_interrupt, 0, |
88358ab0 BH |
1111 | &pata_macio_sht); |
1112 | } | |
1113 | ||
0ec24914 GKH |
1114 | static int pata_macio_attach(struct macio_dev *mdev, |
1115 | const struct of_device_id *match) | |
88358ab0 BH |
1116 | { |
1117 | struct pata_macio_priv *priv; | |
1118 | resource_size_t tfregs, dmaregs = 0; | |
1119 | unsigned long irq; | |
1120 | int rc; | |
1121 | ||
1122 | /* Check for broken device-trees */ | |
1123 | if (macio_resource_count(mdev) == 0) { | |
1124 | dev_err(&mdev->ofdev.dev, | |
1125 | "No addresses for controller\n"); | |
1126 | return -ENXIO; | |
1127 | } | |
1128 | ||
1129 | /* Enable managed resources */ | |
1130 | macio_enable_devres(mdev); | |
1131 | ||
1132 | /* Allocate and init private data structure */ | |
1133 | priv = devm_kzalloc(&mdev->ofdev.dev, | |
1134 | sizeof(struct pata_macio_priv), GFP_KERNEL); | |
3e342770 | 1135 | if (!priv) |
88358ab0 | 1136 | return -ENOMEM; |
3e342770 | 1137 | |
61c7a080 | 1138 | priv->node = of_node_get(mdev->ofdev.dev.of_node); |
88358ab0 BH |
1139 | priv->mdev = mdev; |
1140 | priv->dev = &mdev->ofdev.dev; | |
1141 | ||
1142 | /* Request memory resource for taskfile registers */ | |
1143 | if (macio_request_resource(mdev, 0, "pata-macio")) { | |
1144 | dev_err(&mdev->ofdev.dev, | |
1145 | "Cannot obtain taskfile resource\n"); | |
1146 | return -EBUSY; | |
1147 | } | |
1148 | tfregs = macio_resource_start(mdev, 0); | |
1149 | ||
1150 | /* Request resources for DMA registers if any */ | |
1151 | if (macio_resource_count(mdev) >= 2) { | |
1152 | if (macio_request_resource(mdev, 1, "pata-macio-dma")) | |
1153 | dev_err(&mdev->ofdev.dev, | |
1154 | "Cannot obtain DMA resource\n"); | |
1155 | else | |
1156 | dmaregs = macio_resource_start(mdev, 1); | |
1157 | } | |
1158 | ||
1159 | /* | |
1160 | * Fixup missing IRQ for some old implementations with broken | |
1161 | * device-trees. | |
1162 | * | |
1163 | * This is a bit bogus, it should be fixed in the device-tree itself, | |
1164 | * via the existing macio fixups, based on the type of interrupt | |
1165 | * controller in the machine. However, I have no test HW for this case, | |
1166 | * and this trick works well enough on those old machines... | |
1167 | */ | |
1168 | if (macio_irq_count(mdev) == 0) { | |
1169 | dev_warn(&mdev->ofdev.dev, | |
1170 | "No interrupts for controller, using 13\n"); | |
1171 | irq = irq_create_mapping(NULL, 13); | |
1172 | } else | |
1173 | irq = macio_irq(mdev, 0); | |
1174 | ||
1175 | /* Prevvent media bay callbacks until fully registered */ | |
1176 | lock_media_bay(priv->mdev->media_bay); | |
1177 | ||
1178 | /* Get register addresses and call common initialization */ | |
1179 | rc = pata_macio_common_init(priv, | |
1180 | tfregs, /* Taskfile regs */ | |
1181 | dmaregs, /* DBDMA regs */ | |
1182 | 0, /* Feature control */ | |
1183 | irq); | |
1184 | unlock_media_bay(priv->mdev->media_bay); | |
1185 | ||
1186 | return rc; | |
1187 | } | |
1188 | ||
0ec24914 | 1189 | static int pata_macio_detach(struct macio_dev *mdev) |
88358ab0 BH |
1190 | { |
1191 | struct ata_host *host = macio_get_drvdata(mdev); | |
1192 | struct pata_macio_priv *priv = host->private_data; | |
1193 | ||
1194 | lock_media_bay(priv->mdev->media_bay); | |
1195 | ||
1196 | /* Make sure the mediabay callback doesn't try to access | |
1197 | * dead stuff | |
1198 | */ | |
1199 | priv->host->private_data = NULL; | |
1200 | ||
1201 | ata_host_detach(host); | |
1202 | ||
1203 | unlock_media_bay(priv->mdev->media_bay); | |
1204 | ||
1205 | return 0; | |
1206 | } | |
1207 | ||
58eb8cd5 | 1208 | #ifdef CONFIG_PM_SLEEP |
88358ab0 BH |
1209 | static int pata_macio_suspend(struct macio_dev *mdev, pm_message_t mesg) |
1210 | { | |
1211 | struct ata_host *host = macio_get_drvdata(mdev); | |
1212 | ||
1213 | return pata_macio_do_suspend(host->private_data, mesg); | |
1214 | } | |
1215 | ||
1216 | static int pata_macio_resume(struct macio_dev *mdev) | |
1217 | { | |
1218 | struct ata_host *host = macio_get_drvdata(mdev); | |
1219 | ||
1220 | return pata_macio_do_resume(host->private_data); | |
1221 | } | |
58eb8cd5 | 1222 | #endif /* CONFIG_PM_SLEEP */ |
88358ab0 BH |
1223 | |
1224 | #ifdef CONFIG_PMAC_MEDIABAY | |
1225 | static void pata_macio_mb_event(struct macio_dev* mdev, int mb_state) | |
1226 | { | |
1227 | struct ata_host *host = macio_get_drvdata(mdev); | |
1228 | struct ata_port *ap; | |
1229 | struct ata_eh_info *ehi; | |
1230 | struct ata_device *dev; | |
1231 | unsigned long flags; | |
1232 | ||
1233 | if (!host || !host->private_data) | |
1234 | return; | |
1235 | ap = host->ports[0]; | |
1236 | spin_lock_irqsave(ap->lock, flags); | |
1237 | ehi = &ap->link.eh_info; | |
1238 | if (mb_state == MB_CD) { | |
1239 | ata_ehi_push_desc(ehi, "mediabay plug"); | |
1240 | ata_ehi_hotplugged(ehi); | |
1241 | ata_port_freeze(ap); | |
1242 | } else { | |
1243 | ata_ehi_push_desc(ehi, "mediabay unplug"); | |
1244 | ata_for_each_dev(dev, &ap->link, ALL) | |
1245 | dev->flags |= ATA_DFLAG_DETACH; | |
1246 | ata_port_abort(ap); | |
1247 | } | |
1248 | spin_unlock_irqrestore(ap->lock, flags); | |
1249 | ||
1250 | } | |
1251 | #endif /* CONFIG_PMAC_MEDIABAY */ | |
1252 | ||
1253 | ||
0ec24914 GKH |
1254 | static int pata_macio_pci_attach(struct pci_dev *pdev, |
1255 | const struct pci_device_id *id) | |
88358ab0 BH |
1256 | { |
1257 | struct pata_macio_priv *priv; | |
1258 | struct device_node *np; | |
1259 | resource_size_t rbase; | |
1260 | ||
1261 | /* We cannot use a MacIO controller without its OF device node */ | |
1262 | np = pci_device_to_OF_node(pdev); | |
1263 | if (np == NULL) { | |
1264 | dev_err(&pdev->dev, | |
1265 | "Cannot find OF device node for controller\n"); | |
1266 | return -ENODEV; | |
1267 | } | |
1268 | ||
1269 | /* Check that it can be enabled */ | |
1270 | if (pcim_enable_device(pdev)) { | |
1271 | dev_err(&pdev->dev, | |
1272 | "Cannot enable controller PCI device\n"); | |
1273 | return -ENXIO; | |
1274 | } | |
1275 | ||
1276 | /* Allocate and init private data structure */ | |
1277 | priv = devm_kzalloc(&pdev->dev, | |
1278 | sizeof(struct pata_macio_priv), GFP_KERNEL); | |
3e342770 | 1279 | if (!priv) |
88358ab0 | 1280 | return -ENOMEM; |
3e342770 | 1281 | |
88358ab0 BH |
1282 | priv->node = of_node_get(np); |
1283 | priv->pdev = pdev; | |
1284 | priv->dev = &pdev->dev; | |
1285 | ||
1286 | /* Get MMIO regions */ | |
1287 | if (pci_request_regions(pdev, "pata-macio")) { | |
1288 | dev_err(&pdev->dev, | |
1289 | "Cannot obtain PCI resources\n"); | |
1290 | return -EBUSY; | |
1291 | } | |
1292 | ||
1293 | /* Get register addresses and call common initialization */ | |
1294 | rbase = pci_resource_start(pdev, 0); | |
1295 | if (pata_macio_common_init(priv, | |
1296 | rbase + 0x2000, /* Taskfile regs */ | |
1297 | rbase + 0x1000, /* DBDMA regs */ | |
1298 | rbase, /* Feature control */ | |
1299 | pdev->irq)) | |
1300 | return -ENXIO; | |
1301 | ||
1302 | return 0; | |
1303 | } | |
1304 | ||
0ec24914 | 1305 | static void pata_macio_pci_detach(struct pci_dev *pdev) |
88358ab0 | 1306 | { |
0a86e1c8 | 1307 | struct ata_host *host = pci_get_drvdata(pdev); |
88358ab0 BH |
1308 | |
1309 | ata_host_detach(host); | |
1310 | } | |
1311 | ||
58eb8cd5 | 1312 | #ifdef CONFIG_PM_SLEEP |
88358ab0 BH |
1313 | static int pata_macio_pci_suspend(struct pci_dev *pdev, pm_message_t mesg) |
1314 | { | |
0a86e1c8 | 1315 | struct ata_host *host = pci_get_drvdata(pdev); |
88358ab0 BH |
1316 | |
1317 | return pata_macio_do_suspend(host->private_data, mesg); | |
1318 | } | |
1319 | ||
1320 | static int pata_macio_pci_resume(struct pci_dev *pdev) | |
1321 | { | |
0a86e1c8 | 1322 | struct ata_host *host = pci_get_drvdata(pdev); |
88358ab0 BH |
1323 | |
1324 | return pata_macio_do_resume(host->private_data); | |
1325 | } | |
58eb8cd5 | 1326 | #endif /* CONFIG_PM_SLEEP */ |
88358ab0 | 1327 | |
e3779f6a | 1328 | static const struct of_device_id pata_macio_match[] = |
88358ab0 BH |
1329 | { |
1330 | { | |
1331 | .name = "IDE", | |
1332 | }, | |
1333 | { | |
1334 | .name = "ATA", | |
1335 | }, | |
1336 | { | |
1337 | .type = "ide", | |
1338 | }, | |
1339 | { | |
1340 | .type = "ata", | |
1341 | }, | |
1342 | {}, | |
1343 | }; | |
469eabb3 | 1344 | MODULE_DEVICE_TABLE(of, pata_macio_match); |
88358ab0 BH |
1345 | |
1346 | static struct macio_driver pata_macio_driver = | |
1347 | { | |
c2cdf6ab BH |
1348 | .driver = { |
1349 | .name = "pata-macio", | |
1350 | .owner = THIS_MODULE, | |
1351 | .of_match_table = pata_macio_match, | |
1352 | }, | |
88358ab0 BH |
1353 | .probe = pata_macio_attach, |
1354 | .remove = pata_macio_detach, | |
58eb8cd5 | 1355 | #ifdef CONFIG_PM_SLEEP |
88358ab0 BH |
1356 | .suspend = pata_macio_suspend, |
1357 | .resume = pata_macio_resume, | |
1358 | #endif | |
1359 | #ifdef CONFIG_PMAC_MEDIABAY | |
1360 | .mediabay_event = pata_macio_mb_event, | |
1361 | #endif | |
88358ab0 BH |
1362 | }; |
1363 | ||
1364 | static const struct pci_device_id pata_macio_pci_match[] = { | |
1365 | { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_UNI_N_ATA), 0 }, | |
1366 | { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID_ATA100), 0 }, | |
1367 | { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_K2_ATA100), 0 }, | |
1368 | { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_SH_ATA), 0 }, | |
1369 | { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID2_ATA), 0 }, | |
1370 | {}, | |
1371 | }; | |
1372 | ||
1373 | static struct pci_driver pata_macio_pci_driver = { | |
1374 | .name = "pata-pci-macio", | |
1375 | .id_table = pata_macio_pci_match, | |
1376 | .probe = pata_macio_pci_attach, | |
1377 | .remove = pata_macio_pci_detach, | |
58eb8cd5 | 1378 | #ifdef CONFIG_PM_SLEEP |
88358ab0 BH |
1379 | .suspend = pata_macio_pci_suspend, |
1380 | .resume = pata_macio_pci_resume, | |
1381 | #endif | |
1382 | .driver = { | |
1383 | .owner = THIS_MODULE, | |
1384 | }, | |
1385 | }; | |
1386 | MODULE_DEVICE_TABLE(pci, pata_macio_pci_match); | |
1387 | ||
1388 | ||
1389 | static int __init pata_macio_init(void) | |
1390 | { | |
1391 | int rc; | |
1392 | ||
1393 | if (!machine_is(powermac)) | |
1394 | return -ENODEV; | |
1395 | ||
1396 | rc = pci_register_driver(&pata_macio_pci_driver); | |
1397 | if (rc) | |
1398 | return rc; | |
1399 | rc = macio_register_driver(&pata_macio_driver); | |
1400 | if (rc) { | |
1401 | pci_unregister_driver(&pata_macio_pci_driver); | |
1402 | return rc; | |
1403 | } | |
1404 | return 0; | |
1405 | } | |
1406 | ||
1407 | static void __exit pata_macio_exit(void) | |
1408 | { | |
1409 | macio_unregister_driver(&pata_macio_driver); | |
1410 | pci_unregister_driver(&pata_macio_pci_driver); | |
1411 | } | |
1412 | ||
1413 | module_init(pata_macio_init); | |
1414 | module_exit(pata_macio_exit); | |
1415 | ||
1416 | MODULE_AUTHOR("Benjamin Herrenschmidt"); | |
1417 | MODULE_DESCRIPTION("Apple MacIO PATA driver"); | |
1418 | MODULE_LICENSE("GPL"); | |
1419 | MODULE_VERSION(DRV_VERSION); |