]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | # |
2 | # ATM device configuration | |
3 | # | |
4 | ||
5 | menu "ATM drivers" | |
6 | depends on NETDEVICES && ATM | |
7 | ||
fb296449 CW |
8 | config ATM_DUMMY |
9 | tristate "Dummy ATM driver" | |
10 | depends on ATM | |
11 | help | |
12 | Dummy ATM driver. Useful for proxy signalling, testing, | |
13 | and development. If unsure, say N. | |
14 | ||
1da177e4 LT |
15 | config ATM_TCP |
16 | tristate "ATM over TCP" | |
17 | depends on INET && ATM | |
18 | help | |
19 | ATM over TCP driver. Useful mainly for development and for | |
20 | experiments. If unsure, say N. | |
21 | ||
22 | config ATM_LANAI | |
23 | tristate "Efficient Networks Speedstream 3010" | |
24 | depends on PCI && ATM | |
25 | help | |
26 | Supports ATM cards based on the Efficient Networks "Lanai" | |
27 | chipset such as the Speedstream 3010 and the ENI-25p. The | |
28 | Speedstream 3060 is currently not supported since we don't | |
29 | have the code to drive the on-board Alcatel DSL chipset (yet). | |
30 | ||
31 | config ATM_ENI | |
32 | tristate "Efficient Networks ENI155P" | |
33 | depends on PCI && ATM | |
34 | ---help--- | |
35 | Driver for the Efficient Networks ENI155p series and SMC ATM | |
36 | Power155 155 Mbps ATM adapters. Both, the versions with 512KB and | |
37 | 2MB on-board RAM (Efficient calls them "C" and "S", respectively), | |
38 | and the FPGA and the ASIC Tonga versions of the board are supported. | |
39 | The driver works with MMF (-MF or ...F) and UTP-5 (-U5 or ...D) | |
40 | adapters. | |
41 | ||
42 | To compile this driver as a module, choose M here: the module will | |
43 | be called eni. | |
44 | ||
45 | config ATM_ENI_DEBUG | |
46 | bool "Enable extended debugging" | |
47 | depends on ATM_ENI | |
48 | help | |
49 | Extended debugging records various events and displays that list | |
50 | when an inconsistency is detected. This mechanism is faster than | |
51 | generally using printks, but still has some impact on performance. | |
52 | Note that extended debugging may create certain race conditions | |
53 | itself. Enable this ONLY if you suspect problems with the driver. | |
54 | ||
55 | config ATM_ENI_TUNE_BURST | |
56 | bool "Fine-tune burst settings" | |
57 | depends on ATM_ENI | |
58 | ---help--- | |
59 | In order to obtain good throughput, the ENI NIC can transfer | |
60 | multiple words of data per PCI bus access cycle. Such a multi-word | |
61 | transfer is called a burst. | |
62 | ||
63 | The default settings for the burst sizes are suitable for most PCI | |
64 | chipsets. However, in some cases, large bursts may overrun buffers | |
65 | in the PCI chipset and cause data corruption. In such cases, large | |
66 | bursts must be disabled and only (slower) small bursts can be used. | |
67 | The burst sizes can be set independently in the send (TX) and | |
68 | receive (RX) direction. | |
69 | ||
70 | Note that enabling many different burst sizes in the same direction | |
71 | may increase the cost of setting up a transfer such that the | |
72 | resulting throughput is lower than when using only the largest | |
73 | available burst size. | |
74 | ||
75 | Also, sometimes larger bursts lead to lower throughput, e.g. on an | |
76 | Intel 440FX board, a drop from 135 Mbps to 103 Mbps was observed | |
77 | when going from 8W to 16W bursts. | |
78 | ||
79 | config ATM_ENI_BURST_TX_16W | |
80 | bool "Enable 16W TX bursts (discouraged)" | |
81 | depends on ATM_ENI_TUNE_BURST | |
82 | help | |
83 | Burst sixteen words at once in the send direction. This may work | |
84 | with recent PCI chipsets, but is known to fail with older chipsets. | |
85 | ||
86 | config ATM_ENI_BURST_TX_8W | |
87 | bool "Enable 8W TX bursts (recommended)" | |
88 | depends on ATM_ENI_TUNE_BURST | |
89 | help | |
90 | Burst eight words at once in the send direction. This is the default | |
91 | setting. | |
92 | ||
93 | config ATM_ENI_BURST_TX_4W | |
94 | bool "Enable 4W TX bursts (optional)" | |
95 | depends on ATM_ENI_TUNE_BURST | |
96 | help | |
97 | Burst four words at once in the send direction. You may want to try | |
98 | this if you have disabled 8W bursts. Enabling 4W if 8W is also set | |
99 | may or may not improve throughput. | |
100 | ||
101 | config ATM_ENI_BURST_TX_2W | |
102 | bool "Enable 2W TX bursts (optional)" | |
103 | depends on ATM_ENI_TUNE_BURST | |
104 | help | |
105 | Burst two words at once in the send direction. You may want to try | |
106 | this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or 8W | |
107 | are also set may or may not improve throughput. | |
108 | ||
109 | config ATM_ENI_BURST_RX_16W | |
110 | bool "Enable 16W RX bursts (discouraged)" | |
111 | depends on ATM_ENI_TUNE_BURST | |
112 | help | |
113 | Burst sixteen words at once in the receive direction. This may work | |
114 | with recent PCI chipsets, but is known to fail with older chipsets. | |
115 | ||
116 | config ATM_ENI_BURST_RX_8W | |
117 | bool "Enable 8W RX bursts (discouraged)" | |
118 | depends on ATM_ENI_TUNE_BURST | |
119 | help | |
120 | Burst eight words at once in the receive direction. This may work | |
121 | with recent PCI chipsets, but is known to fail with older chipsets, | |
122 | such as the Intel Neptune series. | |
123 | ||
124 | config ATM_ENI_BURST_RX_4W | |
125 | bool "Enable 4W RX bursts (recommended)" | |
126 | depends on ATM_ENI_TUNE_BURST | |
127 | help | |
128 | Burst four words at once in the receive direction. This is the | |
129 | default setting. Enabling 4W if 8W is also set may or may not | |
130 | improve throughput. | |
131 | ||
132 | config ATM_ENI_BURST_RX_2W | |
133 | bool "Enable 2W RX bursts (optional)" | |
134 | depends on ATM_ENI_TUNE_BURST | |
135 | help | |
136 | Burst two words at once in the receive direction. You may want to | |
137 | try this if you have disabled 4W and 8W bursts. Enabling 2W if 4W or | |
138 | 8W are also set may or may not improve throughput. | |
139 | ||
140 | config ATM_FIRESTREAM | |
141 | tristate "Fujitsu FireStream (FS50/FS155) " | |
142 | depends on PCI && ATM | |
143 | help | |
144 | Driver for the Fujitsu FireStream 155 (MB86697) and | |
145 | FireStream 50 (MB86695) ATM PCI chips. | |
146 | ||
147 | To compile this driver as a module, choose M here: the module will | |
148 | be called firestream. | |
149 | ||
150 | config ATM_ZATM | |
151 | tristate "ZeitNet ZN1221/ZN1225" | |
152 | depends on PCI && ATM | |
153 | help | |
154 | Driver for the ZeitNet ZN1221 (MMF) and ZN1225 (UTP-5) 155 Mbps ATM | |
155 | adapters. | |
156 | ||
157 | To compile this driver as a module, choose M here: the module will | |
158 | be called zatm. | |
159 | ||
160 | config ATM_ZATM_DEBUG | |
161 | bool "Enable extended debugging" | |
162 | depends on ATM_ZATM | |
163 | help | |
164 | Extended debugging records various events and displays that list | |
165 | when an inconsistency is detected. This mechanism is faster than | |
166 | generally using printks, but still has some impact on performance. | |
167 | Note that extended debugging may create certain race conditions | |
168 | itself. Enable this ONLY if you suspect problems with the driver. | |
169 | ||
1da177e4 LT |
170 | config ATM_NICSTAR |
171 | tristate "IDT 77201 (NICStAR) (ForeRunnerLE)" | |
172 | depends on PCI && ATM && !64BIT | |
173 | help | |
174 | The NICStAR chipset family is used in a large number of ATM NICs for | |
175 | 25 and for 155 Mbps, including IDT cards and the Fore ForeRunnerLE | |
176 | series. Say Y if you have one of those. | |
177 | ||
178 | To compile this driver as a module, choose M here: the module will | |
179 | be called nicstar. | |
180 | ||
181 | config ATM_NICSTAR_USE_SUNI | |
182 | bool "Use suni PHY driver (155Mbps)" | |
183 | depends on ATM_NICSTAR | |
184 | help | |
185 | Support for the S-UNI and compatible PHYsical layer chips. These are | |
186 | found in most 155Mbps NICStAR based ATM cards, namely in the | |
187 | ForeRunner LE155 cards. This driver provides detection of cable~ | |
188 | removal and reinsertion and provides some statistics. This driver | |
189 | doesn't have removal capability when compiled as a module, so if you | |
190 | need that capability don't include S-UNI support (it's not needed to | |
191 | make the card work). | |
192 | ||
193 | config ATM_NICSTAR_USE_IDT77105 | |
194 | bool "Use IDT77015 PHY driver (25Mbps)" | |
195 | depends on ATM_NICSTAR | |
196 | help | |
197 | Support for the PHYsical layer chip in ForeRunner LE25 cards. In | |
198 | addition to cable removal/reinsertion detection, this driver allows | |
199 | you to control the loopback mode of the chip via a dedicated IOCTL. | |
200 | This driver is required for proper handling of temporary carrier | |
201 | loss, so if you have a 25Mbps NICStAR based ATM card you must say Y. | |
202 | ||
203 | config ATM_IDT77252 | |
204 | tristate "IDT 77252 (NICStAR II)" | |
205 | depends on PCI && ATM | |
206 | help | |
207 | Driver for the IDT 77252 ATM PCI chips. | |
208 | ||
209 | To compile this driver as a module, choose M here: the module will | |
210 | be called idt77252. | |
211 | ||
212 | config ATM_IDT77252_DEBUG | |
213 | bool "Enable debugging messages" | |
214 | depends on ATM_IDT77252 | |
215 | help | |
216 | Somewhat useful debugging messages are available. The choice of | |
217 | messages is controlled by a bitmap. This may be specified as a | |
218 | module argument. See the file <file:drivers/atm/idt77252.h> for | |
219 | the meanings of the bits in the mask. | |
220 | ||
221 | When active, these messages can have a significant impact on the | |
222 | speed of the driver, and the size of your syslog files! When | |
223 | inactive, they will have only a modest impact on performance. | |
224 | ||
225 | config ATM_IDT77252_RCV_ALL | |
226 | bool "Receive ALL cells in raw queue" | |
227 | depends on ATM_IDT77252 | |
228 | help | |
229 | Enable receiving of all cells on the ATM link, that do not match | |
230 | an open connection in the raw cell queue of the driver. Useful | |
231 | for debugging or special applications only, so the safe answer is N. | |
232 | ||
233 | config ATM_IDT77252_USE_SUNI | |
234 | bool | |
235 | depends on ATM_IDT77252 | |
236 | default y | |
237 | ||
238 | config ATM_AMBASSADOR | |
239 | tristate "Madge Ambassador (Collage PCI 155 Server)" | |
240 | depends on PCI && ATM | |
0a858857 | 241 | select BITREVERSE |
1da177e4 LT |
242 | help |
243 | This is a driver for ATMizer based ATM card produced by Madge | |
244 | Networks Ltd. Say Y (or M to compile as a module named ambassador) | |
245 | here if you have one of these cards. | |
246 | ||
247 | config ATM_AMBASSADOR_DEBUG | |
248 | bool "Enable debugging messages" | |
249 | depends on ATM_AMBASSADOR | |
250 | ---help--- | |
251 | Somewhat useful debugging messages are available. The choice of | |
252 | messages is controlled by a bitmap. This may be specified as a | |
253 | module argument (kernel command line argument as well?), changed | |
254 | dynamically using an ioctl (not yet) or changed by sending the | |
255 | string "Dxxxx" to VCI 1023 (where x is a hex digit). See the file | |
256 | <file:drivers/atm/ambassador.h> for the meanings of the bits in the | |
257 | mask. | |
258 | ||
259 | When active, these messages can have a significant impact on the | |
260 | speed of the driver, and the size of your syslog files! When | |
261 | inactive, they will have only a modest impact on performance. | |
262 | ||
263 | config ATM_HORIZON | |
264 | tristate "Madge Horizon [Ultra] (Collage PCI 25 and Collage PCI 155 Client)" | |
265 | depends on PCI && ATM | |
266 | help | |
267 | This is a driver for the Horizon chipset ATM adapter cards once | |
268 | produced by Madge Networks Ltd. Say Y (or M to compile as a module | |
269 | named horizon) here if you have one of these cards. | |
270 | ||
271 | config ATM_HORIZON_DEBUG | |
272 | bool "Enable debugging messages" | |
273 | depends on ATM_HORIZON | |
274 | ---help--- | |
275 | Somewhat useful debugging messages are available. The choice of | |
276 | messages is controlled by a bitmap. This may be specified as a | |
277 | module argument (kernel command line argument as well?), changed | |
278 | dynamically using an ioctl (not yet) or changed by sending the | |
279 | string "Dxxxx" to VCI 1023 (where x is a hex digit). See the file | |
280 | <file:drivers/atm/horizon.h> for the meanings of the bits in the | |
281 | mask. | |
282 | ||
283 | When active, these messages can have a significant impact on the | |
284 | speed of the driver, and the size of your syslog files! When | |
285 | inactive, they will have only a modest impact on performance. | |
286 | ||
287 | config ATM_IA | |
288 | tristate "Interphase ATM PCI x575/x525/x531" | |
289 | depends on PCI && ATM && !64BIT | |
290 | ---help--- | |
291 | This is a driver for the Interphase (i)ChipSAR adapter cards | |
292 | which include a variety of variants in term of the size of the | |
293 | control memory (128K-1KVC, 512K-4KVC), the size of the packet | |
294 | memory (128K, 512K, 1M), and the PHY type (Single/Multi mode OC3, | |
295 | UTP155, UTP25, DS3 and E3). Go to: | |
296 | <http://www.iphase.com/products/ClassSheet.cfm?ClassID=ATM> | |
297 | for more info about the cards. Say Y (or M to compile as a module | |
298 | named iphase) here if you have one of these cards. | |
299 | ||
300 | See the file <file:Documentation/networking/iphase.txt> for further | |
301 | details. | |
302 | ||
303 | config ATM_IA_DEBUG | |
304 | bool "Enable debugging messages" | |
305 | depends on ATM_IA | |
306 | ---help--- | |
307 | Somewhat useful debugging messages are available. The choice of | |
308 | messages is controlled by a bitmap. This may be specified as a | |
309 | module argument (kernel command line argument as well?), changed | |
310 | dynamically using an ioctl (Get the debug utility, iadbg, from | |
311 | <ftp://ftp.iphase.com/pub/atm/pci/>). | |
312 | ||
313 | See the file <file:drivers/atm/iphase.h> for the meanings of the | |
314 | bits in the mask. | |
315 | ||
316 | When active, these messages can have a significant impact on the | |
317 | speed of the driver, and the size of your syslog files! When | |
318 | inactive, they will have only a modest impact on performance. | |
319 | ||
320 | config ATM_FORE200E_MAYBE | |
321 | tristate "FORE Systems 200E-series" | |
322 | depends on (PCI || SBUS) && ATM | |
323 | ---help--- | |
324 | This is a driver for the FORE Systems 200E-series ATM adapter | |
325 | cards. It simultaneously supports PCA-200E and SBA-200E models | |
326 | on PCI and SBUS hosts. Say Y (or M to compile as a module | |
327 | named fore_200e) here if you have one of these ATM adapters. | |
328 | ||
329 | Note that the driver will actually be compiled only if you | |
330 | additionally enable the support for PCA-200E and/or SBA-200E | |
331 | cards. | |
332 | ||
333 | See the file <file:Documentation/networking/fore200e.txt> for | |
334 | further details. | |
335 | ||
336 | config ATM_FORE200E_PCA | |
337 | bool "PCA-200E support" | |
338 | depends on ATM_FORE200E_MAYBE && PCI | |
339 | help | |
340 | Say Y here if you want your PCA-200E cards to be probed. | |
341 | ||
342 | config ATM_FORE200E_PCA_DEFAULT_FW | |
343 | bool "Use default PCA-200E firmware (normally enabled)" | |
344 | depends on ATM_FORE200E_PCA | |
345 | help | |
346 | Use the default PCA-200E firmware data shipped with the driver. | |
347 | ||
348 | Normal users do not have to deal with the firmware stuff, so | |
349 | they should say Y here. | |
350 | ||
351 | config ATM_FORE200E_PCA_FW | |
352 | string "Pathname of user-supplied binary firmware" | |
353 | depends on ATM_FORE200E_PCA && !ATM_FORE200E_PCA_DEFAULT_FW | |
354 | default "" | |
355 | help | |
356 | This defines the pathname of an alternative PCA-200E binary | |
357 | firmware image supplied by the user. This pathname may be | |
358 | absolute or relative to the drivers/atm directory. | |
359 | ||
360 | The driver comes with an adequate firmware image, so normal users do | |
361 | not have to supply an alternative one. They just say Y to "Use | |
362 | default PCA-200E firmware" instead. | |
363 | ||
364 | config ATM_FORE200E_SBA | |
365 | bool "SBA-200E support" | |
366 | depends on ATM_FORE200E_MAYBE && SBUS | |
367 | help | |
368 | Say Y here if you want your SBA-200E cards to be probed. | |
369 | ||
370 | config ATM_FORE200E_SBA_DEFAULT_FW | |
371 | bool "Use default SBA-200E firmware (normally enabled)" | |
372 | depends on ATM_FORE200E_SBA | |
373 | help | |
374 | Use the default SBA-200E firmware data shipped with the driver. | |
375 | ||
376 | Normal users do not have to deal with the firmware stuff, so | |
377 | they should say Y here. | |
378 | ||
379 | config ATM_FORE200E_SBA_FW | |
380 | string "Pathname of user-supplied binary firmware" | |
381 | depends on ATM_FORE200E_SBA && !ATM_FORE200E_SBA_DEFAULT_FW | |
382 | default "" | |
383 | help | |
384 | This defines the pathname of an alternative SBA-200E binary | |
385 | firmware image supplied by the user. This pathname may be | |
386 | absolute or relative to the drivers/atm directory. | |
387 | ||
388 | The driver comes with an adequate firmware image, so normal users do | |
389 | not have to supply an alternative one. They just say Y to "Use | |
390 | default SBA-200E firmware", above. | |
391 | ||
392 | config ATM_FORE200E_USE_TASKLET | |
393 | bool "Defer interrupt work to a tasklet" | |
394 | depends on (PCI || SBUS) && (ATM_FORE200E_PCA || ATM_FORE200E_SBA) | |
395 | default n | |
396 | help | |
397 | This defers work to be done by the interrupt handler to a | |
00181fc9 | 398 | tasklet instead of handling everything at interrupt time. This |
1da177e4 LT |
399 | may improve the responsive of the host. |
400 | ||
401 | config ATM_FORE200E_TX_RETRY | |
402 | int "Maximum number of tx retries" | |
403 | depends on (PCI || SBUS) && (ATM_FORE200E_PCA || ATM_FORE200E_SBA) | |
404 | default "16" | |
405 | ---help--- | |
406 | Specifies the number of times the driver attempts to transmit | |
407 | a message before giving up, if the transmit queue of the ATM card | |
408 | is transiently saturated. | |
409 | ||
410 | Saturation of the transmit queue may occur only under extreme | |
411 | conditions, e.g. when a fast host continuously submits very small | |
412 | frames (<64 bytes) or raw AAL0 cells (48 bytes) to the ATM adapter. | |
413 | ||
414 | Note that under common conditions, it is unlikely that you encounter | |
415 | a saturation of the transmit queue, so the retry mechanism never | |
416 | comes into play. | |
417 | ||
418 | config ATM_FORE200E_DEBUG | |
419 | int "Debugging level (0-3)" | |
420 | depends on (PCI || SBUS) && (ATM_FORE200E_PCA || ATM_FORE200E_SBA) | |
421 | default "0" | |
422 | help | |
423 | Specifies the level of debugging messages issued by the driver. | |
424 | The verbosity of the driver increases with the value of this | |
425 | parameter. | |
426 | ||
427 | When active, these messages can have a significant impact on | |
428 | the performances of the driver, and the size of your syslog files! | |
429 | Keep the debugging level to 0 during normal operations. | |
430 | ||
431 | config ATM_FORE200E | |
432 | tristate | |
433 | depends on (PCI || SBUS) && (ATM_FORE200E_PCA || ATM_FORE200E_SBA) | |
434 | default m if ATM_FORE200E_MAYBE!=y | |
435 | default y if ATM_FORE200E_MAYBE=y | |
436 | ||
437 | config ATM_HE | |
438 | tristate "ForeRunner HE Series" | |
439 | depends on PCI && ATM | |
440 | help | |
441 | This is a driver for the Marconi ForeRunner HE-series ATM adapter | |
442 | cards. It simultaneously supports the 155 and 622 versions. | |
443 | ||
444 | config ATM_HE_USE_SUNI | |
445 | bool "Use S/UNI PHY driver" | |
446 | depends on ATM_HE | |
447 | help | |
448 | Support for the S/UNI-Ultra and S/UNI-622 found in the ForeRunner | |
449 | HE cards. This driver provides carrier detection some statistics. | |
450 | ||
451 | endmenu | |
452 |