]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | # |
2 | # IPMI device configuration | |
3 | # | |
4 | ||
bcf6b4bb | 5 | menuconfig IPMI_HANDLER |
1da177e4 | 6 | tristate 'IPMI top-level message handler' |
bcf6b4bb | 7 | depends on HAS_IOMEM |
9f88145f | 8 | select IPMI_DMI_DECODE if DMI |
1da177e4 LT |
9 | help |
10 | This enables the central IPMI message handler, required for IPMI | |
11 | to work. | |
12 | ||
13 | IPMI is a standard for managing sensors (temperature, | |
14 | voltage, etc.) in a system. | |
15 | ||
16 | See <file:Documentation/IPMI.txt> for more details on the driver. | |
17 | ||
18 | If unsure, say N. | |
19 | ||
9f88145f CM |
20 | config IPMI_DMI_DECODE |
21 | bool | |
22 | ||
bcf6b4bb JE |
23 | if IPMI_HANDLER |
24 | ||
1da177e4 LT |
25 | config IPMI_PANIC_EVENT |
26 | bool 'Generate a panic event to all BMCs on a panic' | |
1da177e4 | 27 | help |
1c9f98d1 CM |
28 | When a panic occurs, this will cause the IPMI message handler to, |
29 | by default, generate an IPMI event describing the panic to each | |
30 | interface registered with the message handler. This is always | |
31 | available, the module parameter for ipmi_msghandler named | |
32 | panic_op can be set to "event" to chose this value, this config | |
33 | simply causes the default value to be set to "event". | |
1da177e4 LT |
34 | |
35 | config IPMI_PANIC_STRING | |
36 | bool 'Generate OEM events containing the panic string' | |
37 | depends on IPMI_PANIC_EVENT | |
38 | help | |
1c9f98d1 CM |
39 | When a panic occurs, this will cause the IPMI message handler to, |
40 | by default, generate IPMI OEM type f0 events holding the IPMB | |
41 | address of the panic generator (byte 4 of the event), a sequence | |
42 | number for the string (byte 5 of the event) and part of the | |
43 | string (the rest of the event). Bytes 1, 2, and 3 are the normal | |
44 | usage for an OEM event. You can fetch these events and use the | |
45 | sequence numbers to piece the string together. This config | |
46 | parameter sets the default value to generate these events, | |
47 | the module parameter for ipmi_msghandler named panic_op can | |
48 | be set to "string" to chose this value, this config simply | |
49 | causes the default value to be set to "string". | |
1da177e4 LT |
50 | |
51 | config IPMI_DEVICE_INTERFACE | |
52 | tristate 'Device interface for IPMI' | |
1da177e4 LT |
53 | help |
54 | This provides an IOCTL interface to the IPMI message handler so | |
55 | userland processes may use IPMI. It supports poll() and select(). | |
56 | ||
57 | config IPMI_SI | |
58 | tristate 'IPMI System Interface handler' | |
1da177e4 LT |
59 | help |
60 | Provides a driver for System Interfaces (KCS, SMIC, BT). | |
61 | Currently, only KCS and SMIC are supported. If | |
62 | you are using IPMI, you should probably say "y" here. | |
63 | ||
25930707 CM |
64 | config IPMI_SSIF |
65 | tristate 'IPMI SMBus handler (SSIF)' | |
66 | select I2C | |
67 | help | |
68 | Provides a driver for a SMBus interface to a BMC, meaning that you | |
69 | have a driver that must be accessed over an I2C bus instead of a | |
70 | standard interface. This module requires I2C support. | |
71 | ||
6a11e5c6 JK |
72 | config IPMI_POWERNV |
73 | depends on PPC_POWERNV | |
74 | tristate 'POWERNV (OPAL firmware) IPMI interface' | |
75 | help | |
76 | Provides a driver for OPAL firmware-based IPMI interfaces. | |
77 | ||
1da177e4 LT |
78 | config IPMI_WATCHDOG |
79 | tristate 'IPMI Watchdog Timer' | |
1da177e4 LT |
80 | help |
81 | This enables the IPMI watchdog timer. | |
82 | ||
83 | config IPMI_POWEROFF | |
84 | tristate 'IPMI Poweroff' | |
1da177e4 LT |
85 | help |
86 | This enables a function to power off the system with IPMI if | |
87 | the IPMI management controller is capable of this. | |
88 | ||
bcf6b4bb | 89 | endif # IPMI_HANDLER |
54f9c4d0 | 90 | |
20d60f61 HW |
91 | config IPMI_KCS_BMC |
92 | tristate | |
93 | ||
be2ed207 HW |
94 | config ASPEED_KCS_IPMI_BMC |
95 | depends on ARCH_ASPEED || COMPILE_TEST | |
96 | select IPMI_KCS_BMC | |
97 | select REGMAP_MMIO | |
98 | tristate "Aspeed KCS IPMI BMC driver" | |
99 | help | |
100 | Provides a driver for the KCS (Keyboard Controller Style) IPMI | |
101 | interface found on Aspeed SOCs (AST2400 and AST2500). | |
102 | ||
103 | The driver implements the BMC side of the KCS contorller, it | |
104 | provides the access of KCS IO space for BMC side. | |
105 | ||
6b2e54f7 HW |
106 | config NPCM7XX_KCS_IPMI_BMC |
107 | depends on ARCH_NPCM7XX || COMPILE_TEST | |
108 | select IPMI_KCS_BMC | |
109 | select REGMAP_MMIO | |
110 | tristate "NPCM7xx KCS IPMI BMC driver" | |
111 | help | |
112 | Provides a driver for the KCS (Keyboard Controller Style) IPMI | |
113 | interface found on Nuvoton NPCM7xx SOCs. | |
114 | ||
115 | The driver implements the BMC side of the KCS contorller, it | |
116 | provides the access of KCS IO space for BMC side. | |
117 | ||
118 | This support is also available as a module. If so, the module | |
119 | will be called kcs_bmc_npcm7xx. | |
120 | ||
54f9c4d0 | 121 | config ASPEED_BT_IPMI_BMC |
eb994594 AJ |
122 | depends on ARCH_ASPEED || COMPILE_TEST |
123 | depends on REGMAP && REGMAP_MMIO && MFD_SYSCON | |
54f9c4d0 AP |
124 | tristate "BT IPMI bmc driver" |
125 | help | |
126 | Provides a driver for the BT (Block Transfer) IPMI interface | |
127 | found on Aspeed SOCs (AST2400 and AST2500). The driver | |
128 | implements the BMC side of the BT interface. |