]>
Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * lm90.c - Part of lm_sensors, Linux kernel modules for hardware | |
3 | * monitoring | |
95238364 | 4 | * Copyright (C) 2003-2010 Jean Delvare <khali@linux-fr.org> |
1da177e4 LT |
5 | * |
6 | * Based on the lm83 driver. The LM90 is a sensor chip made by National | |
7 | * Semiconductor. It reports up to two temperatures (its own plus up to | |
8 | * one external one) with a 0.125 deg resolution (1 deg for local | |
a874a10c | 9 | * temperature) and a 3-4 deg accuracy. |
1da177e4 LT |
10 | * |
11 | * This driver also supports the LM89 and LM99, two other sensor chips | |
12 | * made by National Semiconductor. Both have an increased remote | |
13 | * temperature measurement accuracy (1 degree), and the LM99 | |
14 | * additionally shifts remote temperatures (measured and limits) by 16 | |
97ae60bb | 15 | * degrees, which allows for higher temperatures measurement. |
44bbe87e | 16 | * Note that there is no way to differentiate between both chips. |
97ae60bb | 17 | * When device is auto-detected, the driver will assume an LM99. |
1da177e4 LT |
18 | * |
19 | * This driver also supports the LM86, another sensor chip made by | |
20 | * National Semiconductor. It is exactly similar to the LM90 except it | |
21 | * has a higher accuracy. | |
1da177e4 LT |
22 | * |
23 | * This driver also supports the ADM1032, a sensor chip made by Analog | |
24 | * Devices. That chip is similar to the LM90, with a few differences | |
a874a10c JD |
25 | * that are not handled by this driver. Among others, it has a higher |
26 | * accuracy than the LM90, much like the LM86 does. | |
1da177e4 LT |
27 | * |
28 | * This driver also supports the MAX6657, MAX6658 and MAX6659 sensor | |
a874a10c | 29 | * chips made by Maxim. These chips are similar to the LM86. |
44bbe87e | 30 | * Note that there is no easy way to differentiate between the three |
6948708d GR |
31 | * variants. We use the device address to detect MAX6659, which will result |
32 | * in a detection as max6657 if it is on address 0x4c. The extra address | |
33 | * and features of the MAX6659 are only supported if the chip is configured | |
34 | * explicitly as max6659, or if its address is not 0x4c. | |
35 | * These chips lack the remote temperature offset feature. | |
1da177e4 | 36 | * |
1a51e068 DW |
37 | * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and |
38 | * MAX6692 chips made by Maxim. These are again similar to the LM86, | |
39 | * but they use unsigned temperature values and can report temperatures | |
40 | * from 0 to 145 degrees. | |
271dabf5 | 41 | * |
32c82a93 RB |
42 | * This driver also supports the MAX6680 and MAX6681, two other sensor |
43 | * chips made by Maxim. These are quite similar to the other Maxim | |
a874a10c JD |
44 | * chips. The MAX6680 and MAX6681 only differ in the pinout so they can |
45 | * be treated identically. | |
32c82a93 | 46 | * |
06e1c0a2 GR |
47 | * This driver also supports the MAX6695 and MAX6696, two other sensor |
48 | * chips made by Maxim. These are also quite similar to other Maxim | |
49 | * chips, but support three temperature sensors instead of two. MAX6695 | |
50 | * and MAX6696 only differ in the pinout so they can be treated identically. | |
51 | * | |
5a4e5e6a GR |
52 | * This driver also supports ADT7461 and ADT7461A from Analog Devices as well as |
53 | * NCT1008 from ON Semiconductor. The chips are supported in both compatibility | |
54 | * and extended mode. They are mostly compatible with LM90 except for a data | |
55 | * format difference for the temperature value registers. | |
1da177e4 LT |
56 | * |
57 | * Since the LM90 was the first chipset supported by this driver, most | |
58 | * comments will refer to this chipset, but are actually general and | |
59 | * concern all supported chipsets, unless mentioned otherwise. | |
60 | * | |
61 | * This program is free software; you can redistribute it and/or modify | |
62 | * it under the terms of the GNU General Public License as published by | |
63 | * the Free Software Foundation; either version 2 of the License, or | |
64 | * (at your option) any later version. | |
65 | * | |
66 | * This program is distributed in the hope that it will be useful, | |
67 | * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
68 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
69 | * GNU General Public License for more details. | |
70 | * | |
71 | * You should have received a copy of the GNU General Public License | |
72 | * along with this program; if not, write to the Free Software | |
73 | * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. | |
74 | */ | |
75 | ||
1da177e4 LT |
76 | #include <linux/module.h> |
77 | #include <linux/init.h> | |
78 | #include <linux/slab.h> | |
79 | #include <linux/jiffies.h> | |
80 | #include <linux/i2c.h> | |
10c08f81 | 81 | #include <linux/hwmon-sysfs.h> |
943b0830 MH |
82 | #include <linux/hwmon.h> |
83 | #include <linux/err.h> | |
9a61bf63 | 84 | #include <linux/mutex.h> |
0e39e01c | 85 | #include <linux/sysfs.h> |
1da177e4 LT |
86 | |
87 | /* | |
88 | * Addresses to scan | |
89 | * Address is fully defined internally and cannot be changed except for | |
32c82a93 | 90 | * MAX6659, MAX6680 and MAX6681. |
5a4e5e6a GR |
91 | * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, ADT7461A, MAX6649, |
92 | * MAX6657, MAX6658, NCT1008 and W83L771 have address 0x4c. | |
93 | * ADM1032-2, ADT7461-2, ADT7461A-2, LM89-1, LM99-1, MAX6646, and NCT1008D | |
94 | * have address 0x4d. | |
271dabf5 | 95 | * MAX6647 has address 0x4e. |
13c84951 | 96 | * MAX6659 can have address 0x4c, 0x4d or 0x4e. |
32c82a93 RB |
97 | * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, |
98 | * 0x4c, 0x4d or 0x4e. | |
1da177e4 LT |
99 | */ |
100 | ||
25e9c86d MH |
101 | static const unsigned short normal_i2c[] = { |
102 | 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e, I2C_CLIENT_END }; | |
1da177e4 | 103 | |
13c84951 | 104 | enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680, |
06e1c0a2 | 105 | max6646, w83l771, max6696 }; |
1da177e4 LT |
106 | |
107 | /* | |
108 | * The LM90 registers | |
109 | */ | |
110 | ||
111 | #define LM90_REG_R_MAN_ID 0xFE | |
112 | #define LM90_REG_R_CHIP_ID 0xFF | |
113 | #define LM90_REG_R_CONFIG1 0x03 | |
114 | #define LM90_REG_W_CONFIG1 0x09 | |
115 | #define LM90_REG_R_CONFIG2 0xBF | |
116 | #define LM90_REG_W_CONFIG2 0xBF | |
117 | #define LM90_REG_R_CONVRATE 0x04 | |
118 | #define LM90_REG_W_CONVRATE 0x0A | |
119 | #define LM90_REG_R_STATUS 0x02 | |
120 | #define LM90_REG_R_LOCAL_TEMP 0x00 | |
121 | #define LM90_REG_R_LOCAL_HIGH 0x05 | |
122 | #define LM90_REG_W_LOCAL_HIGH 0x0B | |
123 | #define LM90_REG_R_LOCAL_LOW 0x06 | |
124 | #define LM90_REG_W_LOCAL_LOW 0x0C | |
125 | #define LM90_REG_R_LOCAL_CRIT 0x20 | |
126 | #define LM90_REG_W_LOCAL_CRIT 0x20 | |
127 | #define LM90_REG_R_REMOTE_TEMPH 0x01 | |
128 | #define LM90_REG_R_REMOTE_TEMPL 0x10 | |
129 | #define LM90_REG_R_REMOTE_OFFSH 0x11 | |
130 | #define LM90_REG_W_REMOTE_OFFSH 0x11 | |
131 | #define LM90_REG_R_REMOTE_OFFSL 0x12 | |
132 | #define LM90_REG_W_REMOTE_OFFSL 0x12 | |
133 | #define LM90_REG_R_REMOTE_HIGHH 0x07 | |
134 | #define LM90_REG_W_REMOTE_HIGHH 0x0D | |
135 | #define LM90_REG_R_REMOTE_HIGHL 0x13 | |
136 | #define LM90_REG_W_REMOTE_HIGHL 0x13 | |
137 | #define LM90_REG_R_REMOTE_LOWH 0x08 | |
138 | #define LM90_REG_W_REMOTE_LOWH 0x0E | |
139 | #define LM90_REG_R_REMOTE_LOWL 0x14 | |
140 | #define LM90_REG_W_REMOTE_LOWL 0x14 | |
141 | #define LM90_REG_R_REMOTE_CRIT 0x19 | |
142 | #define LM90_REG_W_REMOTE_CRIT 0x19 | |
143 | #define LM90_REG_R_TCRIT_HYST 0x21 | |
144 | #define LM90_REG_W_TCRIT_HYST 0x21 | |
145 | ||
06e1c0a2 | 146 | /* MAX6646/6647/6649/6657/6658/6659/6695/6696 registers */ |
f65e1708 JD |
147 | |
148 | #define MAX6657_REG_R_LOCAL_TEMPL 0x11 | |
06e1c0a2 | 149 | #define MAX6696_REG_R_STATUS2 0x12 |
6948708d GR |
150 | #define MAX6659_REG_R_REMOTE_EMERG 0x16 |
151 | #define MAX6659_REG_W_REMOTE_EMERG 0x16 | |
152 | #define MAX6659_REG_R_LOCAL_EMERG 0x17 | |
153 | #define MAX6659_REG_W_LOCAL_EMERG 0x17 | |
f65e1708 | 154 | |
0c01b644 GR |
155 | #define LM90_DEF_CONVRATE_RVAL 6 /* Def conversion rate register value */ |
156 | #define LM90_MAX_CONVRATE_MS 16000 /* Maximum conversion rate in ms */ | |
157 | ||
23b2d477 NC |
158 | /* |
159 | * Device flags | |
160 | */ | |
88073bb1 GR |
161 | #define LM90_FLAG_ADT7461_EXT (1 << 0) /* ADT7461 extended mode */ |
162 | /* Device features */ | |
163 | #define LM90_HAVE_OFFSET (1 << 1) /* temperature offset register */ | |
164 | #define LM90_HAVE_LOCAL_EXT (1 << 2) /* extended local temperature */ | |
165 | #define LM90_HAVE_REM_LIMIT_EXT (1 << 3) /* extended remote limit */ | |
6948708d | 166 | #define LM90_HAVE_EMERGENCY (1 << 4) /* 3rd upper (emergency) limit */ |
06e1c0a2 GR |
167 | #define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */ |
168 | #define LM90_HAVE_TEMP3 (1 << 6) /* 3rd temperature sensor */ | |
1179324c | 169 | #define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */ |
23b2d477 | 170 | |
1da177e4 LT |
171 | /* |
172 | * Driver data (common to all clients) | |
173 | */ | |
174 | ||
9b0e8526 JD |
175 | static const struct i2c_device_id lm90_id[] = { |
176 | { "adm1032", adm1032 }, | |
177 | { "adt7461", adt7461 }, | |
5a4e5e6a | 178 | { "adt7461a", adt7461 }, |
9b0e8526 JD |
179 | { "lm90", lm90 }, |
180 | { "lm86", lm86 }, | |
97ae60bb JD |
181 | { "lm89", lm86 }, |
182 | { "lm99", lm99 }, | |
271dabf5 BH |
183 | { "max6646", max6646 }, |
184 | { "max6647", max6646 }, | |
185 | { "max6649", max6646 }, | |
9b0e8526 JD |
186 | { "max6657", max6657 }, |
187 | { "max6658", max6657 }, | |
13c84951 | 188 | { "max6659", max6659 }, |
9b0e8526 JD |
189 | { "max6680", max6680 }, |
190 | { "max6681", max6680 }, | |
06e1c0a2 GR |
191 | { "max6695", max6696 }, |
192 | { "max6696", max6696 }, | |
5a4e5e6a | 193 | { "nct1008", adt7461 }, |
6771ea1f | 194 | { "w83l771", w83l771 }, |
9b0e8526 JD |
195 | { } |
196 | }; | |
197 | MODULE_DEVICE_TABLE(i2c, lm90_id); | |
198 | ||
4667bcb8 GR |
199 | /* |
200 | * chip type specific parameters | |
201 | */ | |
202 | struct lm90_params { | |
203 | u32 flags; /* Capabilities */ | |
204 | u16 alert_alarms; /* Which alarm bits trigger ALERT# */ | |
205 | /* Upper 8 bits for max6695/96 */ | |
0c01b644 | 206 | u8 max_convrate; /* Maximum conversion rate register value */ |
4667bcb8 GR |
207 | }; |
208 | ||
209 | static const struct lm90_params lm90_params[] = { | |
210 | [adm1032] = { | |
1179324c GR |
211 | .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT |
212 | | LM90_HAVE_BROKEN_ALERT, | |
4667bcb8 | 213 | .alert_alarms = 0x7c, |
0c01b644 | 214 | .max_convrate = 10, |
4667bcb8 GR |
215 | }, |
216 | [adt7461] = { | |
1179324c GR |
217 | .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT |
218 | | LM90_HAVE_BROKEN_ALERT, | |
4667bcb8 | 219 | .alert_alarms = 0x7c, |
0c01b644 | 220 | .max_convrate = 10, |
4667bcb8 GR |
221 | }, |
222 | [lm86] = { | |
223 | .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, | |
224 | .alert_alarms = 0x7b, | |
0c01b644 | 225 | .max_convrate = 9, |
4667bcb8 GR |
226 | }, |
227 | [lm90] = { | |
228 | .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, | |
229 | .alert_alarms = 0x7b, | |
0c01b644 | 230 | .max_convrate = 9, |
4667bcb8 GR |
231 | }, |
232 | [lm99] = { | |
233 | .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, | |
234 | .alert_alarms = 0x7b, | |
0c01b644 | 235 | .max_convrate = 9, |
4667bcb8 GR |
236 | }, |
237 | [max6646] = { | |
238 | .flags = LM90_HAVE_LOCAL_EXT, | |
239 | .alert_alarms = 0x7c, | |
0c01b644 | 240 | .max_convrate = 6, |
4667bcb8 GR |
241 | }, |
242 | [max6657] = { | |
243 | .flags = LM90_HAVE_LOCAL_EXT, | |
244 | .alert_alarms = 0x7c, | |
0c01b644 | 245 | .max_convrate = 8, |
4667bcb8 GR |
246 | }, |
247 | [max6659] = { | |
248 | .flags = LM90_HAVE_LOCAL_EXT | LM90_HAVE_EMERGENCY, | |
249 | .alert_alarms = 0x7c, | |
0c01b644 | 250 | .max_convrate = 8, |
4667bcb8 GR |
251 | }, |
252 | [max6680] = { | |
253 | .flags = LM90_HAVE_OFFSET, | |
254 | .alert_alarms = 0x7c, | |
0c01b644 | 255 | .max_convrate = 7, |
4667bcb8 GR |
256 | }, |
257 | [max6696] = { | |
258 | .flags = LM90_HAVE_LOCAL_EXT | LM90_HAVE_EMERGENCY | |
259 | | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3, | |
260 | .alert_alarms = 0x187c, | |
0c01b644 | 261 | .max_convrate = 6, |
4667bcb8 GR |
262 | }, |
263 | [w83l771] = { | |
264 | .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT, | |
265 | .alert_alarms = 0x7c, | |
0c01b644 | 266 | .max_convrate = 8, |
4667bcb8 GR |
267 | }, |
268 | }; | |
269 | ||
1da177e4 LT |
270 | /* |
271 | * Client data (each client gets its own) | |
272 | */ | |
273 | ||
274 | struct lm90_data { | |
1beeffe4 | 275 | struct device *hwmon_dev; |
9a61bf63 | 276 | struct mutex update_lock; |
1da177e4 LT |
277 | char valid; /* zero until following fields are valid */ |
278 | unsigned long last_updated; /* in jiffies */ | |
279 | int kind; | |
4667bcb8 | 280 | u32 flags; |
1da177e4 | 281 | |
0c01b644 GR |
282 | int update_interval; /* in milliseconds */ |
283 | ||
95238364 | 284 | u8 config_orig; /* Original configuration register value */ |
0c01b644 | 285 | u8 convrate_orig; /* Original conversion rate register value */ |
06e1c0a2 GR |
286 | u16 alert_alarms; /* Which alarm bits trigger ALERT# */ |
287 | /* Upper 8 bits for max6695/96 */ | |
0c01b644 | 288 | u8 max_convrate; /* Maximum conversion rate */ |
95238364 | 289 | |
1da177e4 | 290 | /* registers values */ |
06e1c0a2 | 291 | s8 temp8[8]; /* 0: local low limit |
f65e1708 JD |
292 | 1: local high limit |
293 | 2: local critical limit | |
6948708d | 294 | 3: remote critical limit |
06e1c0a2 GR |
295 | 4: local emergency limit (max6659 and max6695/96) |
296 | 5: remote emergency limit (max6659 and max6695/96) | |
297 | 6: remote 2 critical limit (max6695/96 only) | |
298 | 7: remote 2 emergency limit (max6695/96 only) */ | |
299 | s16 temp11[8]; /* 0: remote input | |
30d7394b | 300 | 1: remote low limit |
69f2f96d | 301 | 2: remote high limit |
06e1c0a2 GR |
302 | 3: remote offset (except max6646, max6657/58/59, |
303 | and max6695/96) | |
304 | 4: local input | |
305 | 5: remote 2 input (max6695/96 only) | |
306 | 6: remote 2 low limit (max6695/96 only) | |
307 | 7: remote 2 high limit (ma6695/96 only) */ | |
1da177e4 | 308 | u8 temp_hyst; |
06e1c0a2 | 309 | u16 alarms; /* bitvector (upper 8 bits for max6695/96) */ |
1da177e4 LT |
310 | }; |
311 | ||
15b66ab6 GR |
312 | /* |
313 | * Support functions | |
314 | */ | |
315 | ||
316 | /* | |
317 | * The ADM1032 supports PEC but not on write byte transactions, so we need | |
318 | * to explicitly ask for a transaction without PEC. | |
319 | */ | |
320 | static inline s32 adm1032_write_byte(struct i2c_client *client, u8 value) | |
321 | { | |
322 | return i2c_smbus_xfer(client->adapter, client->addr, | |
323 | client->flags & ~I2C_CLIENT_PEC, | |
324 | I2C_SMBUS_WRITE, value, I2C_SMBUS_BYTE, NULL); | |
325 | } | |
326 | ||
327 | /* | |
328 | * It is assumed that client->update_lock is held (unless we are in | |
329 | * detection or initialization steps). This matters when PEC is enabled, | |
330 | * because we don't want the address pointer to change between the write | |
331 | * byte and the read byte transactions. | |
332 | */ | |
333 | static int lm90_read_reg(struct i2c_client *client, u8 reg, u8 *value) | |
334 | { | |
335 | int err; | |
336 | ||
337 | if (client->flags & I2C_CLIENT_PEC) { | |
338 | err = adm1032_write_byte(client, reg); | |
339 | if (err >= 0) | |
340 | err = i2c_smbus_read_byte(client); | |
341 | } else | |
342 | err = i2c_smbus_read_byte_data(client, reg); | |
343 | ||
344 | if (err < 0) { | |
345 | dev_warn(&client->dev, "Register %#02x read failed (%d)\n", | |
346 | reg, err); | |
347 | return err; | |
348 | } | |
349 | *value = err; | |
350 | ||
351 | return 0; | |
352 | } | |
353 | ||
354 | static int lm90_read16(struct i2c_client *client, u8 regh, u8 regl, u16 *value) | |
355 | { | |
356 | int err; | |
357 | u8 oldh, newh, l; | |
358 | ||
359 | /* | |
360 | * There is a trick here. We have to read two registers to have the | |
361 | * sensor temperature, but we have to beware a conversion could occur | |
25985edc | 362 | * between the readings. The datasheet says we should either use |
15b66ab6 GR |
363 | * the one-shot conversion register, which we don't want to do |
364 | * (disables hardware monitoring) or monitor the busy bit, which is | |
365 | * impossible (we can't read the values and monitor that bit at the | |
366 | * exact same time). So the solution used here is to read the high | |
367 | * byte once, then the low byte, then the high byte again. If the new | |
368 | * high byte matches the old one, then we have a valid reading. Else | |
369 | * we have to read the low byte again, and now we believe we have a | |
370 | * correct reading. | |
371 | */ | |
372 | if ((err = lm90_read_reg(client, regh, &oldh)) | |
373 | || (err = lm90_read_reg(client, regl, &l)) | |
374 | || (err = lm90_read_reg(client, regh, &newh))) | |
375 | return err; | |
376 | if (oldh != newh) { | |
377 | err = lm90_read_reg(client, regl, &l); | |
378 | if (err) | |
379 | return err; | |
380 | } | |
381 | *value = (newh << 8) | l; | |
382 | ||
383 | return 0; | |
384 | } | |
385 | ||
386 | /* | |
387 | * client->update_lock must be held when calling this function (unless we are | |
388 | * in detection or initialization steps), and while a remote channel other | |
389 | * than channel 0 is selected. Also, calling code must make sure to re-select | |
390 | * external channel 0 before releasing the lock. This is necessary because | |
391 | * various registers have different meanings as a result of selecting a | |
392 | * non-default remote channel. | |
393 | */ | |
394 | static inline void lm90_select_remote_channel(struct i2c_client *client, | |
395 | struct lm90_data *data, | |
396 | int channel) | |
397 | { | |
398 | u8 config; | |
399 | ||
400 | if (data->kind == max6696) { | |
401 | lm90_read_reg(client, LM90_REG_R_CONFIG1, &config); | |
402 | config &= ~0x08; | |
403 | if (channel) | |
404 | config |= 0x08; | |
405 | i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, | |
406 | config); | |
407 | } | |
408 | } | |
409 | ||
0c01b644 GR |
410 | /* |
411 | * Set conversion rate. | |
412 | * client->update_lock must be held when calling this function (unless we are | |
413 | * in detection or initialization steps). | |
414 | */ | |
415 | static void lm90_set_convrate(struct i2c_client *client, struct lm90_data *data, | |
416 | unsigned int interval) | |
417 | { | |
418 | int i; | |
419 | unsigned int update_interval; | |
420 | ||
421 | /* Shift calculations to avoid rounding errors */ | |
422 | interval <<= 6; | |
423 | ||
424 | /* find the nearest update rate */ | |
425 | for (i = 0, update_interval = LM90_MAX_CONVRATE_MS << 6; | |
426 | i < data->max_convrate; i++, update_interval >>= 1) | |
427 | if (interval >= update_interval * 3 / 4) | |
428 | break; | |
429 | ||
430 | i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE, i); | |
431 | data->update_interval = DIV_ROUND_CLOSEST(update_interval, 64); | |
432 | } | |
433 | ||
15b66ab6 GR |
434 | static struct lm90_data *lm90_update_device(struct device *dev) |
435 | { | |
436 | struct i2c_client *client = to_i2c_client(dev); | |
437 | struct lm90_data *data = i2c_get_clientdata(client); | |
0c01b644 | 438 | unsigned long next_update; |
15b66ab6 GR |
439 | |
440 | mutex_lock(&data->update_lock); | |
441 | ||
0c01b644 GR |
442 | next_update = data->last_updated |
443 | + msecs_to_jiffies(data->update_interval) + 1; | |
444 | if (time_after(jiffies, next_update) || !data->valid) { | |
15b66ab6 GR |
445 | u8 h, l; |
446 | u8 alarms; | |
447 | ||
448 | dev_dbg(&client->dev, "Updating lm90 data.\n"); | |
449 | lm90_read_reg(client, LM90_REG_R_LOCAL_LOW, &data->temp8[0]); | |
450 | lm90_read_reg(client, LM90_REG_R_LOCAL_HIGH, &data->temp8[1]); | |
451 | lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT, &data->temp8[2]); | |
452 | lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT, &data->temp8[3]); | |
453 | lm90_read_reg(client, LM90_REG_R_TCRIT_HYST, &data->temp_hyst); | |
454 | ||
455 | if (data->flags & LM90_HAVE_LOCAL_EXT) { | |
456 | lm90_read16(client, LM90_REG_R_LOCAL_TEMP, | |
457 | MAX6657_REG_R_LOCAL_TEMPL, | |
458 | &data->temp11[4]); | |
459 | } else { | |
460 | if (lm90_read_reg(client, LM90_REG_R_LOCAL_TEMP, | |
461 | &h) == 0) | |
462 | data->temp11[4] = h << 8; | |
463 | } | |
464 | lm90_read16(client, LM90_REG_R_REMOTE_TEMPH, | |
465 | LM90_REG_R_REMOTE_TEMPL, &data->temp11[0]); | |
466 | ||
467 | if (lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH, &h) == 0) { | |
468 | data->temp11[1] = h << 8; | |
469 | if ((data->flags & LM90_HAVE_REM_LIMIT_EXT) | |
470 | && lm90_read_reg(client, LM90_REG_R_REMOTE_LOWL, | |
471 | &l) == 0) | |
472 | data->temp11[1] |= l; | |
473 | } | |
474 | if (lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH, &h) == 0) { | |
475 | data->temp11[2] = h << 8; | |
476 | if ((data->flags & LM90_HAVE_REM_LIMIT_EXT) | |
477 | && lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHL, | |
478 | &l) == 0) | |
479 | data->temp11[2] |= l; | |
480 | } | |
481 | ||
482 | if (data->flags & LM90_HAVE_OFFSET) { | |
483 | if (lm90_read_reg(client, LM90_REG_R_REMOTE_OFFSH, | |
484 | &h) == 0 | |
485 | && lm90_read_reg(client, LM90_REG_R_REMOTE_OFFSL, | |
486 | &l) == 0) | |
487 | data->temp11[3] = (h << 8) | l; | |
488 | } | |
489 | if (data->flags & LM90_HAVE_EMERGENCY) { | |
490 | lm90_read_reg(client, MAX6659_REG_R_LOCAL_EMERG, | |
491 | &data->temp8[4]); | |
492 | lm90_read_reg(client, MAX6659_REG_R_REMOTE_EMERG, | |
493 | &data->temp8[5]); | |
494 | } | |
495 | lm90_read_reg(client, LM90_REG_R_STATUS, &alarms); | |
496 | data->alarms = alarms; /* save as 16 bit value */ | |
497 | ||
498 | if (data->kind == max6696) { | |
499 | lm90_select_remote_channel(client, data, 1); | |
500 | lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT, | |
501 | &data->temp8[6]); | |
502 | lm90_read_reg(client, MAX6659_REG_R_REMOTE_EMERG, | |
503 | &data->temp8[7]); | |
504 | lm90_read16(client, LM90_REG_R_REMOTE_TEMPH, | |
505 | LM90_REG_R_REMOTE_TEMPL, &data->temp11[5]); | |
506 | if (!lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH, &h)) | |
507 | data->temp11[6] = h << 8; | |
508 | if (!lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH, &h)) | |
509 | data->temp11[7] = h << 8; | |
510 | lm90_select_remote_channel(client, data, 0); | |
511 | ||
512 | if (!lm90_read_reg(client, MAX6696_REG_R_STATUS2, | |
513 | &alarms)) | |
514 | data->alarms |= alarms << 8; | |
515 | } | |
516 | ||
517 | /* Re-enable ALERT# output if it was originally enabled and | |
518 | * relevant alarms are all clear */ | |
519 | if ((data->config_orig & 0x80) == 0 | |
520 | && (data->alarms & data->alert_alarms) == 0) { | |
521 | u8 config; | |
522 | ||
523 | lm90_read_reg(client, LM90_REG_R_CONFIG1, &config); | |
524 | if (config & 0x80) { | |
525 | dev_dbg(&client->dev, "Re-enabling ALERT#\n"); | |
526 | i2c_smbus_write_byte_data(client, | |
527 | LM90_REG_W_CONFIG1, | |
528 | config & ~0x80); | |
529 | } | |
530 | } | |
531 | ||
532 | data->last_updated = jiffies; | |
533 | data->valid = 1; | |
534 | } | |
535 | ||
536 | mutex_unlock(&data->update_lock); | |
537 | ||
538 | return data; | |
539 | } | |
540 | ||
cea50fe2 NC |
541 | /* |
542 | * Conversions | |
543 | * For local temperatures and limits, critical limits and the hysteresis | |
544 | * value, the LM90 uses signed 8-bit values with LSB = 1 degree Celsius. | |
545 | * For remote temperatures and limits, it uses signed 11-bit values with | |
271dabf5 BH |
546 | * LSB = 0.125 degree Celsius, left-justified in 16-bit registers. Some |
547 | * Maxim chips use unsigned values. | |
cea50fe2 NC |
548 | */ |
549 | ||
9d4d3834 | 550 | static inline int temp_from_s8(s8 val) |
cea50fe2 NC |
551 | { |
552 | return val * 1000; | |
553 | } | |
554 | ||
271dabf5 BH |
555 | static inline int temp_from_u8(u8 val) |
556 | { | |
557 | return val * 1000; | |
558 | } | |
559 | ||
9d4d3834 | 560 | static inline int temp_from_s16(s16 val) |
cea50fe2 NC |
561 | { |
562 | return val / 32 * 125; | |
563 | } | |
564 | ||
271dabf5 BH |
565 | static inline int temp_from_u16(u16 val) |
566 | { | |
567 | return val / 32 * 125; | |
568 | } | |
569 | ||
9d4d3834 | 570 | static s8 temp_to_s8(long val) |
cea50fe2 NC |
571 | { |
572 | if (val <= -128000) | |
573 | return -128; | |
574 | if (val >= 127000) | |
575 | return 127; | |
576 | if (val < 0) | |
577 | return (val - 500) / 1000; | |
578 | return (val + 500) / 1000; | |
579 | } | |
580 | ||
271dabf5 BH |
581 | static u8 temp_to_u8(long val) |
582 | { | |
583 | if (val <= 0) | |
584 | return 0; | |
585 | if (val >= 255000) | |
586 | return 255; | |
587 | return (val + 500) / 1000; | |
588 | } | |
589 | ||
9d4d3834 | 590 | static s16 temp_to_s16(long val) |
cea50fe2 NC |
591 | { |
592 | if (val <= -128000) | |
593 | return 0x8000; | |
594 | if (val >= 127875) | |
595 | return 0x7FE0; | |
596 | if (val < 0) | |
597 | return (val - 62) / 125 * 32; | |
598 | return (val + 62) / 125 * 32; | |
599 | } | |
600 | ||
601 | static u8 hyst_to_reg(long val) | |
602 | { | |
603 | if (val <= 0) | |
604 | return 0; | |
605 | if (val >= 30500) | |
606 | return 31; | |
607 | return (val + 500) / 1000; | |
608 | } | |
609 | ||
610 | /* | |
23b2d477 NC |
611 | * ADT7461 in compatibility mode is almost identical to LM90 except that |
612 | * attempts to write values that are outside the range 0 < temp < 127 are | |
613 | * treated as the boundary value. | |
614 | * | |
615 | * ADT7461 in "extended mode" operation uses unsigned integers offset by | |
616 | * 64 (e.g., 0 -> -64 degC). The range is restricted to -64..191 degC. | |
cea50fe2 | 617 | */ |
9d4d3834 | 618 | static inline int temp_from_u8_adt7461(struct lm90_data *data, u8 val) |
cea50fe2 | 619 | { |
23b2d477 NC |
620 | if (data->flags & LM90_FLAG_ADT7461_EXT) |
621 | return (val - 64) * 1000; | |
622 | else | |
9d4d3834 | 623 | return temp_from_s8(val); |
cea50fe2 NC |
624 | } |
625 | ||
9d4d3834 | 626 | static inline int temp_from_u16_adt7461(struct lm90_data *data, u16 val) |
cea50fe2 | 627 | { |
23b2d477 NC |
628 | if (data->flags & LM90_FLAG_ADT7461_EXT) |
629 | return (val - 0x4000) / 64 * 250; | |
630 | else | |
9d4d3834 | 631 | return temp_from_s16(val); |
23b2d477 NC |
632 | } |
633 | ||
9d4d3834 | 634 | static u8 temp_to_u8_adt7461(struct lm90_data *data, long val) |
23b2d477 NC |
635 | { |
636 | if (data->flags & LM90_FLAG_ADT7461_EXT) { | |
637 | if (val <= -64000) | |
638 | return 0; | |
639 | if (val >= 191000) | |
640 | return 0xFF; | |
641 | return (val + 500 + 64000) / 1000; | |
642 | } else { | |
643 | if (val <= 0) | |
644 | return 0; | |
645 | if (val >= 127000) | |
646 | return 127; | |
647 | return (val + 500) / 1000; | |
648 | } | |
649 | } | |
650 | ||
9d4d3834 | 651 | static u16 temp_to_u16_adt7461(struct lm90_data *data, long val) |
23b2d477 NC |
652 | { |
653 | if (data->flags & LM90_FLAG_ADT7461_EXT) { | |
654 | if (val <= -64000) | |
655 | return 0; | |
656 | if (val >= 191750) | |
657 | return 0xFFC0; | |
658 | return (val + 64000 + 125) / 250 * 64; | |
659 | } else { | |
660 | if (val <= 0) | |
661 | return 0; | |
662 | if (val >= 127750) | |
663 | return 0x7FC0; | |
664 | return (val + 125) / 250 * 64; | |
665 | } | |
cea50fe2 NC |
666 | } |
667 | ||
1da177e4 LT |
668 | /* |
669 | * Sysfs stuff | |
670 | */ | |
671 | ||
30d7394b JD |
672 | static ssize_t show_temp8(struct device *dev, struct device_attribute *devattr, |
673 | char *buf) | |
674 | { | |
675 | struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); | |
676 | struct lm90_data *data = lm90_update_device(dev); | |
23b2d477 NC |
677 | int temp; |
678 | ||
679 | if (data->kind == adt7461) | |
9d4d3834 | 680 | temp = temp_from_u8_adt7461(data, data->temp8[attr->index]); |
271dabf5 BH |
681 | else if (data->kind == max6646) |
682 | temp = temp_from_u8(data->temp8[attr->index]); | |
23b2d477 | 683 | else |
9d4d3834 | 684 | temp = temp_from_s8(data->temp8[attr->index]); |
23b2d477 | 685 | |
97ae60bb JD |
686 | /* +16 degrees offset for temp2 for the LM99 */ |
687 | if (data->kind == lm99 && attr->index == 3) | |
688 | temp += 16000; | |
689 | ||
23b2d477 | 690 | return sprintf(buf, "%d\n", temp); |
30d7394b JD |
691 | } |
692 | ||
693 | static ssize_t set_temp8(struct device *dev, struct device_attribute *devattr, | |
694 | const char *buf, size_t count) | |
695 | { | |
06e1c0a2 | 696 | static const u8 reg[8] = { |
30d7394b JD |
697 | LM90_REG_W_LOCAL_LOW, |
698 | LM90_REG_W_LOCAL_HIGH, | |
699 | LM90_REG_W_LOCAL_CRIT, | |
700 | LM90_REG_W_REMOTE_CRIT, | |
6948708d GR |
701 | MAX6659_REG_W_LOCAL_EMERG, |
702 | MAX6659_REG_W_REMOTE_EMERG, | |
06e1c0a2 GR |
703 | LM90_REG_W_REMOTE_CRIT, |
704 | MAX6659_REG_W_REMOTE_EMERG, | |
30d7394b JD |
705 | }; |
706 | ||
707 | struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); | |
708 | struct i2c_client *client = to_i2c_client(dev); | |
709 | struct lm90_data *data = i2c_get_clientdata(client); | |
30d7394b | 710 | int nr = attr->index; |
11e57812 GR |
711 | long val; |
712 | int err; | |
713 | ||
714 | err = strict_strtol(buf, 10, &val); | |
715 | if (err < 0) | |
716 | return err; | |
30d7394b | 717 | |
97ae60bb JD |
718 | /* +16 degrees offset for temp2 for the LM99 */ |
719 | if (data->kind == lm99 && attr->index == 3) | |
720 | val -= 16000; | |
721 | ||
9a61bf63 | 722 | mutex_lock(&data->update_lock); |
30d7394b | 723 | if (data->kind == adt7461) |
9d4d3834 | 724 | data->temp8[nr] = temp_to_u8_adt7461(data, val); |
271dabf5 BH |
725 | else if (data->kind == max6646) |
726 | data->temp8[nr] = temp_to_u8(val); | |
30d7394b | 727 | else |
9d4d3834 | 728 | data->temp8[nr] = temp_to_s8(val); |
06e1c0a2 GR |
729 | |
730 | lm90_select_remote_channel(client, data, nr >= 6); | |
f65e1708 | 731 | i2c_smbus_write_byte_data(client, reg[nr], data->temp8[nr]); |
06e1c0a2 GR |
732 | lm90_select_remote_channel(client, data, 0); |
733 | ||
9a61bf63 | 734 | mutex_unlock(&data->update_lock); |
30d7394b | 735 | return count; |
1da177e4 | 736 | } |
30d7394b JD |
737 | |
738 | static ssize_t show_temp11(struct device *dev, struct device_attribute *devattr, | |
739 | char *buf) | |
740 | { | |
96512861 | 741 | struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); |
30d7394b | 742 | struct lm90_data *data = lm90_update_device(dev); |
23b2d477 NC |
743 | int temp; |
744 | ||
745 | if (data->kind == adt7461) | |
9d4d3834 | 746 | temp = temp_from_u16_adt7461(data, data->temp11[attr->index]); |
271dabf5 BH |
747 | else if (data->kind == max6646) |
748 | temp = temp_from_u16(data->temp11[attr->index]); | |
23b2d477 | 749 | else |
9d4d3834 | 750 | temp = temp_from_s16(data->temp11[attr->index]); |
23b2d477 | 751 | |
97ae60bb JD |
752 | /* +16 degrees offset for temp2 for the LM99 */ |
753 | if (data->kind == lm99 && attr->index <= 2) | |
754 | temp += 16000; | |
755 | ||
23b2d477 | 756 | return sprintf(buf, "%d\n", temp); |
1da177e4 | 757 | } |
30d7394b JD |
758 | |
759 | static ssize_t set_temp11(struct device *dev, struct device_attribute *devattr, | |
760 | const char *buf, size_t count) | |
761 | { | |
96512861 GR |
762 | struct { |
763 | u8 high; | |
764 | u8 low; | |
06e1c0a2 GR |
765 | int channel; |
766 | } reg[5] = { | |
767 | { LM90_REG_W_REMOTE_LOWH, LM90_REG_W_REMOTE_LOWL, 0 }, | |
768 | { LM90_REG_W_REMOTE_HIGHH, LM90_REG_W_REMOTE_HIGHL, 0 }, | |
769 | { LM90_REG_W_REMOTE_OFFSH, LM90_REG_W_REMOTE_OFFSL, 0 }, | |
770 | { LM90_REG_W_REMOTE_LOWH, LM90_REG_W_REMOTE_LOWL, 1 }, | |
771 | { LM90_REG_W_REMOTE_HIGHH, LM90_REG_W_REMOTE_HIGHL, 1 } | |
30d7394b JD |
772 | }; |
773 | ||
96512861 | 774 | struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); |
30d7394b JD |
775 | struct i2c_client *client = to_i2c_client(dev); |
776 | struct lm90_data *data = i2c_get_clientdata(client); | |
96512861 GR |
777 | int nr = attr->nr; |
778 | int index = attr->index; | |
11e57812 GR |
779 | long val; |
780 | int err; | |
781 | ||
782 | err = strict_strtol(buf, 10, &val); | |
783 | if (err < 0) | |
784 | return err; | |
30d7394b | 785 | |
97ae60bb | 786 | /* +16 degrees offset for temp2 for the LM99 */ |
96512861 | 787 | if (data->kind == lm99 && index <= 2) |
97ae60bb JD |
788 | val -= 16000; |
789 | ||
9a61bf63 | 790 | mutex_lock(&data->update_lock); |
30d7394b | 791 | if (data->kind == adt7461) |
96512861 | 792 | data->temp11[index] = temp_to_u16_adt7461(data, val); |
271dabf5 | 793 | else if (data->kind == max6646) |
96512861 | 794 | data->temp11[index] = temp_to_u8(val) << 8; |
88073bb1 | 795 | else if (data->flags & LM90_HAVE_REM_LIMIT_EXT) |
96512861 | 796 | data->temp11[index] = temp_to_s16(val); |
88073bb1 | 797 | else |
96512861 | 798 | data->temp11[index] = temp_to_s8(val) << 8; |
5f502a83 | 799 | |
06e1c0a2 | 800 | lm90_select_remote_channel(client, data, reg[nr].channel); |
96512861 GR |
801 | i2c_smbus_write_byte_data(client, reg[nr].high, |
802 | data->temp11[index] >> 8); | |
88073bb1 | 803 | if (data->flags & LM90_HAVE_REM_LIMIT_EXT) |
96512861 GR |
804 | i2c_smbus_write_byte_data(client, reg[nr].low, |
805 | data->temp11[index] & 0xff); | |
06e1c0a2 GR |
806 | lm90_select_remote_channel(client, data, 0); |
807 | ||
9a61bf63 | 808 | mutex_unlock(&data->update_lock); |
30d7394b | 809 | return count; |
1da177e4 | 810 | } |
30d7394b | 811 | |
11e57812 GR |
812 | static ssize_t show_temphyst(struct device *dev, |
813 | struct device_attribute *devattr, | |
30d7394b JD |
814 | char *buf) |
815 | { | |
816 | struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); | |
817 | struct lm90_data *data = lm90_update_device(dev); | |
23b2d477 NC |
818 | int temp; |
819 | ||
820 | if (data->kind == adt7461) | |
9d4d3834 | 821 | temp = temp_from_u8_adt7461(data, data->temp8[attr->index]); |
ec38fa2b JD |
822 | else if (data->kind == max6646) |
823 | temp = temp_from_u8(data->temp8[attr->index]); | |
23b2d477 | 824 | else |
9d4d3834 | 825 | temp = temp_from_s8(data->temp8[attr->index]); |
23b2d477 | 826 | |
97ae60bb JD |
827 | /* +16 degrees offset for temp2 for the LM99 */ |
828 | if (data->kind == lm99 && attr->index == 3) | |
829 | temp += 16000; | |
830 | ||
9d4d3834 | 831 | return sprintf(buf, "%d\n", temp - temp_from_s8(data->temp_hyst)); |
1da177e4 | 832 | } |
1da177e4 | 833 | |
30d7394b JD |
834 | static ssize_t set_temphyst(struct device *dev, struct device_attribute *dummy, |
835 | const char *buf, size_t count) | |
1da177e4 LT |
836 | { |
837 | struct i2c_client *client = to_i2c_client(dev); | |
838 | struct lm90_data *data = i2c_get_clientdata(client); | |
11e57812 GR |
839 | long val; |
840 | int err; | |
ec38fa2b | 841 | int temp; |
1da177e4 | 842 | |
11e57812 GR |
843 | err = strict_strtol(buf, 10, &val); |
844 | if (err < 0) | |
845 | return err; | |
846 | ||
9a61bf63 | 847 | mutex_lock(&data->update_lock); |
ec38fa2b JD |
848 | if (data->kind == adt7461) |
849 | temp = temp_from_u8_adt7461(data, data->temp8[2]); | |
850 | else if (data->kind == max6646) | |
851 | temp = temp_from_u8(data->temp8[2]); | |
852 | else | |
853 | temp = temp_from_s8(data->temp8[2]); | |
854 | ||
855 | data->temp_hyst = hyst_to_reg(temp - val); | |
1da177e4 | 856 | i2c_smbus_write_byte_data(client, LM90_REG_W_TCRIT_HYST, |
ec38fa2b | 857 | data->temp_hyst); |
9a61bf63 | 858 | mutex_unlock(&data->update_lock); |
1da177e4 LT |
859 | return count; |
860 | } | |
861 | ||
30d7394b JD |
862 | static ssize_t show_alarms(struct device *dev, struct device_attribute *dummy, |
863 | char *buf) | |
1da177e4 LT |
864 | { |
865 | struct lm90_data *data = lm90_update_device(dev); | |
866 | return sprintf(buf, "%d\n", data->alarms); | |
867 | } | |
868 | ||
2d45771e JD |
869 | static ssize_t show_alarm(struct device *dev, struct device_attribute |
870 | *devattr, char *buf) | |
871 | { | |
872 | struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr); | |
873 | struct lm90_data *data = lm90_update_device(dev); | |
874 | int bitnr = attr->index; | |
875 | ||
876 | return sprintf(buf, "%d\n", (data->alarms >> bitnr) & 1); | |
877 | } | |
878 | ||
0c01b644 GR |
879 | static ssize_t show_update_interval(struct device *dev, |
880 | struct device_attribute *attr, char *buf) | |
881 | { | |
882 | struct lm90_data *data = dev_get_drvdata(dev); | |
883 | ||
884 | return sprintf(buf, "%u\n", data->update_interval); | |
885 | } | |
886 | ||
887 | static ssize_t set_update_interval(struct device *dev, | |
888 | struct device_attribute *attr, | |
889 | const char *buf, size_t count) | |
890 | { | |
891 | struct i2c_client *client = to_i2c_client(dev); | |
892 | struct lm90_data *data = i2c_get_clientdata(client); | |
893 | unsigned long val; | |
894 | int err; | |
895 | ||
896 | err = strict_strtoul(buf, 10, &val); | |
897 | if (err) | |
898 | return err; | |
899 | ||
900 | mutex_lock(&data->update_lock); | |
901 | lm90_set_convrate(client, data, val); | |
902 | mutex_unlock(&data->update_lock); | |
903 | ||
904 | return count; | |
905 | } | |
906 | ||
96512861 GR |
907 | static SENSOR_DEVICE_ATTR_2(temp1_input, S_IRUGO, show_temp11, NULL, 0, 4); |
908 | static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp11, NULL, 0, 0); | |
30d7394b | 909 | static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp8, |
f65e1708 | 910 | set_temp8, 0); |
96512861 GR |
911 | static SENSOR_DEVICE_ATTR_2(temp2_min, S_IWUSR | S_IRUGO, show_temp11, |
912 | set_temp11, 0, 1); | |
30d7394b | 913 | static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp8, |
f65e1708 | 914 | set_temp8, 1); |
96512861 GR |
915 | static SENSOR_DEVICE_ATTR_2(temp2_max, S_IWUSR | S_IRUGO, show_temp11, |
916 | set_temp11, 1, 2); | |
30d7394b | 917 | static SENSOR_DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_temp8, |
f65e1708 | 918 | set_temp8, 2); |
30d7394b | 919 | static SENSOR_DEVICE_ATTR(temp2_crit, S_IWUSR | S_IRUGO, show_temp8, |
f65e1708 | 920 | set_temp8, 3); |
30d7394b | 921 | static SENSOR_DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO, show_temphyst, |
f65e1708 JD |
922 | set_temphyst, 2); |
923 | static SENSOR_DEVICE_ATTR(temp2_crit_hyst, S_IRUGO, show_temphyst, NULL, 3); | |
96512861 GR |
924 | static SENSOR_DEVICE_ATTR_2(temp2_offset, S_IWUSR | S_IRUGO, show_temp11, |
925 | set_temp11, 2, 3); | |
2d45771e JD |
926 | |
927 | /* Individual alarm files */ | |
928 | static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 0); | |
929 | static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 1); | |
7817a39e | 930 | static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 2); |
2d45771e JD |
931 | static SENSOR_DEVICE_ATTR(temp2_min_alarm, S_IRUGO, show_alarm, NULL, 3); |
932 | static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 4); | |
933 | static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 5); | |
934 | static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 6); | |
935 | /* Raw alarm file for compatibility */ | |
1da177e4 LT |
936 | static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL); |
937 | ||
0c01b644 GR |
938 | static DEVICE_ATTR(update_interval, S_IRUGO | S_IWUSR, show_update_interval, |
939 | set_update_interval); | |
940 | ||
0e39e01c JD |
941 | static struct attribute *lm90_attributes[] = { |
942 | &sensor_dev_attr_temp1_input.dev_attr.attr, | |
943 | &sensor_dev_attr_temp2_input.dev_attr.attr, | |
944 | &sensor_dev_attr_temp1_min.dev_attr.attr, | |
945 | &sensor_dev_attr_temp2_min.dev_attr.attr, | |
946 | &sensor_dev_attr_temp1_max.dev_attr.attr, | |
947 | &sensor_dev_attr_temp2_max.dev_attr.attr, | |
948 | &sensor_dev_attr_temp1_crit.dev_attr.attr, | |
949 | &sensor_dev_attr_temp2_crit.dev_attr.attr, | |
950 | &sensor_dev_attr_temp1_crit_hyst.dev_attr.attr, | |
951 | &sensor_dev_attr_temp2_crit_hyst.dev_attr.attr, | |
952 | ||
953 | &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr, | |
954 | &sensor_dev_attr_temp2_crit_alarm.dev_attr.attr, | |
7817a39e | 955 | &sensor_dev_attr_temp2_fault.dev_attr.attr, |
0e39e01c JD |
956 | &sensor_dev_attr_temp2_min_alarm.dev_attr.attr, |
957 | &sensor_dev_attr_temp2_max_alarm.dev_attr.attr, | |
958 | &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, | |
959 | &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, | |
960 | &dev_attr_alarms.attr, | |
0c01b644 | 961 | &dev_attr_update_interval.attr, |
0e39e01c JD |
962 | NULL |
963 | }; | |
964 | ||
965 | static const struct attribute_group lm90_group = { | |
966 | .attrs = lm90_attributes, | |
967 | }; | |
968 | ||
6948708d GR |
969 | /* |
970 | * Additional attributes for devices with emergency sensors | |
971 | */ | |
972 | static SENSOR_DEVICE_ATTR(temp1_emergency, S_IWUSR | S_IRUGO, show_temp8, | |
973 | set_temp8, 4); | |
974 | static SENSOR_DEVICE_ATTR(temp2_emergency, S_IWUSR | S_IRUGO, show_temp8, | |
975 | set_temp8, 5); | |
976 | static SENSOR_DEVICE_ATTR(temp1_emergency_hyst, S_IRUGO, show_temphyst, | |
977 | NULL, 4); | |
978 | static SENSOR_DEVICE_ATTR(temp2_emergency_hyst, S_IRUGO, show_temphyst, | |
979 | NULL, 5); | |
980 | ||
981 | static struct attribute *lm90_emergency_attributes[] = { | |
982 | &sensor_dev_attr_temp1_emergency.dev_attr.attr, | |
983 | &sensor_dev_attr_temp2_emergency.dev_attr.attr, | |
984 | &sensor_dev_attr_temp1_emergency_hyst.dev_attr.attr, | |
985 | &sensor_dev_attr_temp2_emergency_hyst.dev_attr.attr, | |
986 | NULL | |
987 | }; | |
988 | ||
989 | static const struct attribute_group lm90_emergency_group = { | |
990 | .attrs = lm90_emergency_attributes, | |
991 | }; | |
992 | ||
06e1c0a2 GR |
993 | static SENSOR_DEVICE_ATTR(temp1_emergency_alarm, S_IRUGO, show_alarm, NULL, 15); |
994 | static SENSOR_DEVICE_ATTR(temp2_emergency_alarm, S_IRUGO, show_alarm, NULL, 13); | |
995 | ||
996 | static struct attribute *lm90_emergency_alarm_attributes[] = { | |
997 | &sensor_dev_attr_temp1_emergency_alarm.dev_attr.attr, | |
998 | &sensor_dev_attr_temp2_emergency_alarm.dev_attr.attr, | |
999 | NULL | |
1000 | }; | |
1001 | ||
1002 | static const struct attribute_group lm90_emergency_alarm_group = { | |
1003 | .attrs = lm90_emergency_alarm_attributes, | |
1004 | }; | |
1005 | ||
1006 | /* | |
1007 | * Additional attributes for devices with 3 temperature sensors | |
1008 | */ | |
1009 | static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp11, NULL, 0, 5); | |
1010 | static SENSOR_DEVICE_ATTR_2(temp3_min, S_IWUSR | S_IRUGO, show_temp11, | |
1011 | set_temp11, 3, 6); | |
1012 | static SENSOR_DEVICE_ATTR_2(temp3_max, S_IWUSR | S_IRUGO, show_temp11, | |
1013 | set_temp11, 4, 7); | |
1014 | static SENSOR_DEVICE_ATTR(temp3_crit, S_IWUSR | S_IRUGO, show_temp8, | |
1015 | set_temp8, 6); | |
1016 | static SENSOR_DEVICE_ATTR(temp3_crit_hyst, S_IRUGO, show_temphyst, NULL, 6); | |
1017 | static SENSOR_DEVICE_ATTR(temp3_emergency, S_IWUSR | S_IRUGO, show_temp8, | |
1018 | set_temp8, 7); | |
1019 | static SENSOR_DEVICE_ATTR(temp3_emergency_hyst, S_IRUGO, show_temphyst, | |
1020 | NULL, 7); | |
1021 | ||
1022 | static SENSOR_DEVICE_ATTR(temp3_crit_alarm, S_IRUGO, show_alarm, NULL, 9); | |
1023 | static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 10); | |
1024 | static SENSOR_DEVICE_ATTR(temp3_min_alarm, S_IRUGO, show_alarm, NULL, 11); | |
1025 | static SENSOR_DEVICE_ATTR(temp3_max_alarm, S_IRUGO, show_alarm, NULL, 12); | |
1026 | static SENSOR_DEVICE_ATTR(temp3_emergency_alarm, S_IRUGO, show_alarm, NULL, 14); | |
1027 | ||
1028 | static struct attribute *lm90_temp3_attributes[] = { | |
1029 | &sensor_dev_attr_temp3_input.dev_attr.attr, | |
1030 | &sensor_dev_attr_temp3_min.dev_attr.attr, | |
1031 | &sensor_dev_attr_temp3_max.dev_attr.attr, | |
1032 | &sensor_dev_attr_temp3_crit.dev_attr.attr, | |
1033 | &sensor_dev_attr_temp3_crit_hyst.dev_attr.attr, | |
1034 | &sensor_dev_attr_temp3_emergency.dev_attr.attr, | |
1035 | &sensor_dev_attr_temp3_emergency_hyst.dev_attr.attr, | |
1036 | ||
1037 | &sensor_dev_attr_temp3_fault.dev_attr.attr, | |
1038 | &sensor_dev_attr_temp3_min_alarm.dev_attr.attr, | |
1039 | &sensor_dev_attr_temp3_max_alarm.dev_attr.attr, | |
1040 | &sensor_dev_attr_temp3_crit_alarm.dev_attr.attr, | |
1041 | &sensor_dev_attr_temp3_emergency_alarm.dev_attr.attr, | |
1042 | NULL | |
1043 | }; | |
1044 | ||
1045 | static const struct attribute_group lm90_temp3_group = { | |
1046 | .attrs = lm90_temp3_attributes, | |
1047 | }; | |
1048 | ||
c3df5806 JD |
1049 | /* pec used for ADM1032 only */ |
1050 | static ssize_t show_pec(struct device *dev, struct device_attribute *dummy, | |
1051 | char *buf) | |
1052 | { | |
1053 | struct i2c_client *client = to_i2c_client(dev); | |
1054 | return sprintf(buf, "%d\n", !!(client->flags & I2C_CLIENT_PEC)); | |
1055 | } | |
1056 | ||
1057 | static ssize_t set_pec(struct device *dev, struct device_attribute *dummy, | |
1058 | const char *buf, size_t count) | |
1059 | { | |
1060 | struct i2c_client *client = to_i2c_client(dev); | |
11e57812 GR |
1061 | long val; |
1062 | int err; | |
1063 | ||
1064 | err = strict_strtol(buf, 10, &val); | |
1065 | if (err < 0) | |
1066 | return err; | |
c3df5806 JD |
1067 | |
1068 | switch (val) { | |
1069 | case 0: | |
1070 | client->flags &= ~I2C_CLIENT_PEC; | |
1071 | break; | |
1072 | case 1: | |
1073 | client->flags |= I2C_CLIENT_PEC; | |
1074 | break; | |
1075 | default: | |
1076 | return -EINVAL; | |
1077 | } | |
1078 | ||
1079 | return count; | |
1080 | } | |
1081 | ||
1082 | static DEVICE_ATTR(pec, S_IWUSR | S_IRUGO, show_pec, set_pec); | |
1083 | ||
1da177e4 LT |
1084 | /* |
1085 | * Real code | |
1086 | */ | |
1087 | ||
15b66ab6 GR |
1088 | /* Return 0 if detection is successful, -ENODEV otherwise */ |
1089 | static int lm90_detect(struct i2c_client *new_client, | |
1090 | struct i2c_board_info *info) | |
8256fe0f | 1091 | { |
15b66ab6 GR |
1092 | struct i2c_adapter *adapter = new_client->adapter; |
1093 | int address = new_client->addr; | |
1094 | const char *name = NULL; | |
1095 | int man_id, chip_id, reg_config1, reg_convrate; | |
8256fe0f | 1096 | |
15b66ab6 GR |
1097 | if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) |
1098 | return -ENODEV; | |
1da177e4 | 1099 | |
8f2fa77c JD |
1100 | /* detection and identification */ |
1101 | if ((man_id = i2c_smbus_read_byte_data(new_client, | |
e0ae87a4 | 1102 | LM90_REG_R_MAN_ID)) < 0 |
8f2fa77c | 1103 | || (chip_id = i2c_smbus_read_byte_data(new_client, |
e0ae87a4 | 1104 | LM90_REG_R_CHIP_ID)) < 0 |
8f2fa77c | 1105 | || (reg_config1 = i2c_smbus_read_byte_data(new_client, |
e0ae87a4 | 1106 | LM90_REG_R_CONFIG1)) < 0 |
8f2fa77c | 1107 | || (reg_convrate = i2c_smbus_read_byte_data(new_client, |
e0ae87a4 | 1108 | LM90_REG_R_CONVRATE)) < 0) |
8f2fa77c JD |
1109 | return -ENODEV; |
1110 | ||
1111 | if ((address == 0x4C || address == 0x4D) | |
1112 | && man_id == 0x01) { /* National Semiconductor */ | |
1113 | int reg_config2; | |
1114 | ||
1115 | reg_config2 = i2c_smbus_read_byte_data(new_client, | |
1116 | LM90_REG_R_CONFIG2); | |
1117 | if (reg_config2 < 0) | |
9b0e8526 | 1118 | return -ENODEV; |
8f2fa77c JD |
1119 | |
1120 | if ((reg_config1 & 0x2A) == 0x00 | |
1121 | && (reg_config2 & 0xF8) == 0x00 | |
1122 | && reg_convrate <= 0x09) { | |
1123 | if (address == 0x4C | |
1124 | && (chip_id & 0xF0) == 0x20) { /* LM90 */ | |
1125 | name = "lm90"; | |
32c82a93 | 1126 | } else |
8f2fa77c JD |
1127 | if ((chip_id & 0xF0) == 0x30) { /* LM89/LM99 */ |
1128 | name = "lm99"; | |
1129 | dev_info(&adapter->dev, | |
1130 | "Assuming LM99 chip at 0x%02x\n", | |
1131 | address); | |
1132 | dev_info(&adapter->dev, | |
1133 | "If it is an LM89, instantiate it " | |
1134 | "with the new_device sysfs " | |
1135 | "interface\n"); | |
271dabf5 | 1136 | } else |
8f2fa77c JD |
1137 | if (address == 0x4C |
1138 | && (chip_id & 0xF0) == 0x10) { /* LM86 */ | |
1139 | name = "lm86"; | |
1da177e4 LT |
1140 | } |
1141 | } | |
8f2fa77c JD |
1142 | } else |
1143 | if ((address == 0x4C || address == 0x4D) | |
1144 | && man_id == 0x41) { /* Analog Devices */ | |
1145 | if ((chip_id & 0xF0) == 0x40 /* ADM1032 */ | |
1146 | && (reg_config1 & 0x3F) == 0x00 | |
1147 | && reg_convrate <= 0x0A) { | |
1148 | name = "adm1032"; | |
1149 | /* The ADM1032 supports PEC, but only if combined | |
1150 | transactions are not used. */ | |
1151 | if (i2c_check_functionality(adapter, | |
1152 | I2C_FUNC_SMBUS_BYTE)) | |
1153 | info->flags |= I2C_CLIENT_PEC; | |
1154 | } else | |
1155 | if (chip_id == 0x51 /* ADT7461 */ | |
1156 | && (reg_config1 & 0x1B) == 0x00 | |
1157 | && reg_convrate <= 0x0A) { | |
1158 | name = "adt7461"; | |
5a4e5e6a GR |
1159 | } else |
1160 | if (chip_id == 0x57 /* ADT7461A, NCT1008 */ | |
1161 | && (reg_config1 & 0x1B) == 0x00 | |
1162 | && reg_convrate <= 0x0A) { | |
1163 | name = "adt7461a"; | |
8f2fa77c JD |
1164 | } |
1165 | } else | |
1166 | if (man_id == 0x4D) { /* Maxim */ | |
06e1c0a2 GR |
1167 | int reg_emerg, reg_emerg2, reg_status2; |
1168 | ||
1169 | /* | |
1170 | * We read MAX6659_REG_R_REMOTE_EMERG twice, and re-read | |
1171 | * LM90_REG_R_MAN_ID in between. If MAX6659_REG_R_REMOTE_EMERG | |
1172 | * exists, both readings will reflect the same value. Otherwise, | |
1173 | * the readings will be different. | |
1174 | */ | |
1175 | if ((reg_emerg = i2c_smbus_read_byte_data(new_client, | |
1176 | MAX6659_REG_R_REMOTE_EMERG)) < 0 | |
1177 | || i2c_smbus_read_byte_data(new_client, LM90_REG_R_MAN_ID) < 0 | |
1178 | || (reg_emerg2 = i2c_smbus_read_byte_data(new_client, | |
1179 | MAX6659_REG_R_REMOTE_EMERG)) < 0 | |
1180 | || (reg_status2 = i2c_smbus_read_byte_data(new_client, | |
1181 | MAX6696_REG_R_STATUS2)) < 0) | |
1182 | return -ENODEV; | |
1183 | ||
8f2fa77c JD |
1184 | /* |
1185 | * The MAX6657, MAX6658 and MAX6659 do NOT have a chip_id | |
1186 | * register. Reading from that address will return the last | |
1187 | * read value, which in our case is those of the man_id | |
1188 | * register. Likewise, the config1 register seems to lack a | |
1189 | * low nibble, so the value will be those of the previous | |
1190 | * read, so in our case those of the man_id register. | |
13c84951 GR |
1191 | * MAX6659 has a third set of upper temperature limit registers. |
1192 | * Those registers also return values on MAX6657 and MAX6658, | |
1193 | * thus the only way to detect MAX6659 is by its address. | |
1194 | * For this reason it will be mis-detected as MAX6657 if its | |
1195 | * address is 0x4C. | |
8f2fa77c JD |
1196 | */ |
1197 | if (chip_id == man_id | |
13c84951 | 1198 | && (address == 0x4C || address == 0x4D || address == 0x4E) |
8f2fa77c JD |
1199 | && (reg_config1 & 0x1F) == (man_id & 0x0F) |
1200 | && reg_convrate <= 0x09) { | |
13c84951 GR |
1201 | if (address == 0x4C) |
1202 | name = "max6657"; | |
1203 | else | |
1204 | name = "max6659"; | |
8f2fa77c | 1205 | } else |
06e1c0a2 GR |
1206 | /* |
1207 | * Even though MAX6695 and MAX6696 do not have a chip ID | |
1208 | * register, reading it returns 0x01. Bit 4 of the config1 | |
1209 | * register is unused and should return zero when read. Bit 0 of | |
1210 | * the status2 register is unused and should return zero when | |
1211 | * read. | |
1212 | * | |
1213 | * MAX6695 and MAX6696 have an additional set of temperature | |
1214 | * limit registers. We can detect those chips by checking if | |
1215 | * one of those registers exists. | |
1216 | */ | |
1217 | if (chip_id == 0x01 | |
1218 | && (reg_config1 & 0x10) == 0x00 | |
1219 | && (reg_status2 & 0x01) == 0x00 | |
1220 | && reg_emerg == reg_emerg2 | |
1221 | && reg_convrate <= 0x07) { | |
1222 | name = "max6696"; | |
1223 | } else | |
8f2fa77c JD |
1224 | /* |
1225 | * The chip_id register of the MAX6680 and MAX6681 holds the | |
1226 | * revision of the chip. The lowest bit of the config1 register | |
1227 | * is unused and should return zero when read, so should the | |
1228 | * second to last bit of config1 (software reset). | |
1229 | */ | |
1230 | if (chip_id == 0x01 | |
1231 | && (reg_config1 & 0x03) == 0x00 | |
1232 | && reg_convrate <= 0x07) { | |
1233 | name = "max6680"; | |
1234 | } else | |
1235 | /* | |
1236 | * The chip_id register of the MAX6646/6647/6649 holds the | |
1237 | * revision of the chip. The lowest 6 bits of the config1 | |
1238 | * register are unused and should return zero when read. | |
1239 | */ | |
1240 | if (chip_id == 0x59 | |
1241 | && (reg_config1 & 0x3f) == 0x00 | |
1242 | && reg_convrate <= 0x07) { | |
1243 | name = "max6646"; | |
1da177e4 | 1244 | } |
6771ea1f JD |
1245 | } else |
1246 | if (address == 0x4C | |
1247 | && man_id == 0x5C) { /* Winbond/Nuvoton */ | |
c4f99a2b JD |
1248 | int reg_config2; |
1249 | ||
1250 | reg_config2 = i2c_smbus_read_byte_data(new_client, | |
1251 | LM90_REG_R_CONFIG2); | |
1252 | if (reg_config2 < 0) | |
1253 | return -ENODEV; | |
1254 | ||
1255 | if ((reg_config1 & 0x2A) == 0x00 | |
1256 | && (reg_config2 & 0xF8) == 0x00) { | |
1257 | if (chip_id == 0x01 /* W83L771W/G */ | |
1258 | && reg_convrate <= 0x09) { | |
1259 | name = "w83l771"; | |
1260 | } else | |
1261 | if ((chip_id & 0xFE) == 0x10 /* W83L771AWG/ASG */ | |
1262 | && reg_convrate <= 0x08) { | |
1263 | name = "w83l771"; | |
1264 | } | |
6771ea1f | 1265 | } |
1da177e4 LT |
1266 | } |
1267 | ||
8f2fa77c JD |
1268 | if (!name) { /* identification failed */ |
1269 | dev_dbg(&adapter->dev, | |
1270 | "Unsupported chip at 0x%02x (man_id=0x%02X, " | |
1271 | "chip_id=0x%02X)\n", address, man_id, chip_id); | |
1272 | return -ENODEV; | |
1da177e4 | 1273 | } |
8f2fa77c | 1274 | |
9b0e8526 JD |
1275 | strlcpy(info->type, name, I2C_NAME_SIZE); |
1276 | ||
1277 | return 0; | |
1278 | } | |
1279 | ||
b6fc1bac GR |
1280 | static void lm90_remove_files(struct i2c_client *client, struct lm90_data *data) |
1281 | { | |
06e1c0a2 GR |
1282 | if (data->flags & LM90_HAVE_TEMP3) |
1283 | sysfs_remove_group(&client->dev.kobj, &lm90_temp3_group); | |
1284 | if (data->flags & LM90_HAVE_EMERGENCY_ALARM) | |
1285 | sysfs_remove_group(&client->dev.kobj, | |
1286 | &lm90_emergency_alarm_group); | |
6948708d GR |
1287 | if (data->flags & LM90_HAVE_EMERGENCY) |
1288 | sysfs_remove_group(&client->dev.kobj, | |
1289 | &lm90_emergency_group); | |
b6fc1bac GR |
1290 | if (data->flags & LM90_HAVE_OFFSET) |
1291 | device_remove_file(&client->dev, | |
1292 | &sensor_dev_attr_temp2_offset.dev_attr); | |
1293 | device_remove_file(&client->dev, &dev_attr_pec); | |
1294 | sysfs_remove_group(&client->dev.kobj, &lm90_group); | |
1295 | } | |
1296 | ||
15b66ab6 GR |
1297 | static void lm90_init_client(struct i2c_client *client) |
1298 | { | |
0c01b644 | 1299 | u8 config, convrate; |
15b66ab6 GR |
1300 | struct lm90_data *data = i2c_get_clientdata(client); |
1301 | ||
0c01b644 GR |
1302 | if (lm90_read_reg(client, LM90_REG_R_CONVRATE, &convrate) < 0) { |
1303 | dev_warn(&client->dev, "Failed to read convrate register!\n"); | |
1304 | convrate = LM90_DEF_CONVRATE_RVAL; | |
1305 | } | |
1306 | data->convrate_orig = convrate; | |
1307 | ||
15b66ab6 GR |
1308 | /* |
1309 | * Start the conversions. | |
1310 | */ | |
0c01b644 | 1311 | lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */ |
15b66ab6 GR |
1312 | if (lm90_read_reg(client, LM90_REG_R_CONFIG1, &config) < 0) { |
1313 | dev_warn(&client->dev, "Initialization failed!\n"); | |
1314 | return; | |
1315 | } | |
1316 | data->config_orig = config; | |
1317 | ||
1318 | /* Check Temperature Range Select */ | |
1319 | if (data->kind == adt7461) { | |
1320 | if (config & 0x04) | |
1321 | data->flags |= LM90_FLAG_ADT7461_EXT; | |
1322 | } | |
1323 | ||
1324 | /* | |
1325 | * Put MAX6680/MAX8881 into extended resolution (bit 0x10, | |
1326 | * 0.125 degree resolution) and range (0x08, extend range | |
1327 | * to -64 degree) mode for the remote temperature sensor. | |
1328 | */ | |
1329 | if (data->kind == max6680) | |
1330 | config |= 0x18; | |
1331 | ||
1332 | /* | |
1333 | * Select external channel 0 for max6695/96 | |
1334 | */ | |
1335 | if (data->kind == max6696) | |
1336 | config &= ~0x08; | |
1337 | ||
1338 | config &= 0xBF; /* run */ | |
1339 | if (config != data->config_orig) /* Only write if changed */ | |
1340 | i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, config); | |
1341 | } | |
1342 | ||
9b0e8526 JD |
1343 | static int lm90_probe(struct i2c_client *new_client, |
1344 | const struct i2c_device_id *id) | |
1345 | { | |
1346 | struct i2c_adapter *adapter = to_i2c_adapter(new_client->dev.parent); | |
1347 | struct lm90_data *data; | |
1348 | int err; | |
1da177e4 | 1349 | |
9b0e8526 JD |
1350 | data = kzalloc(sizeof(struct lm90_data), GFP_KERNEL); |
1351 | if (!data) { | |
1352 | err = -ENOMEM; | |
1353 | goto exit; | |
1354 | } | |
1355 | i2c_set_clientdata(new_client, data); | |
9a61bf63 | 1356 | mutex_init(&data->update_lock); |
1da177e4 | 1357 | |
9b0e8526 JD |
1358 | /* Set the device type */ |
1359 | data->kind = id->driver_data; | |
1360 | if (data->kind == adm1032) { | |
1361 | if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE)) | |
1362 | new_client->flags &= ~I2C_CLIENT_PEC; | |
1363 | } | |
1da177e4 | 1364 | |
53de3342 JD |
1365 | /* Different devices have different alarm bits triggering the |
1366 | * ALERT# output */ | |
4667bcb8 | 1367 | data->alert_alarms = lm90_params[data->kind].alert_alarms; |
53de3342 | 1368 | |
88073bb1 | 1369 | /* Set chip capabilities */ |
4667bcb8 | 1370 | data->flags = lm90_params[data->kind].flags; |
06e1c0a2 | 1371 | |
0c01b644 GR |
1372 | /* Set maximum conversion rate */ |
1373 | data->max_convrate = lm90_params[data->kind].max_convrate; | |
1374 | ||
1da177e4 LT |
1375 | /* Initialize the LM90 chip */ |
1376 | lm90_init_client(new_client); | |
1377 | ||
1378 | /* Register sysfs hooks */ | |
11e57812 GR |
1379 | err = sysfs_create_group(&new_client->dev.kobj, &lm90_group); |
1380 | if (err) | |
9b0e8526 | 1381 | goto exit_free; |
0e39e01c | 1382 | if (new_client->flags & I2C_CLIENT_PEC) { |
11e57812 GR |
1383 | err = device_create_file(&new_client->dev, &dev_attr_pec); |
1384 | if (err) | |
0e39e01c JD |
1385 | goto exit_remove_files; |
1386 | } | |
88073bb1 | 1387 | if (data->flags & LM90_HAVE_OFFSET) { |
11e57812 GR |
1388 | err = device_create_file(&new_client->dev, |
1389 | &sensor_dev_attr_temp2_offset.dev_attr); | |
1390 | if (err) | |
69f2f96d JD |
1391 | goto exit_remove_files; |
1392 | } | |
6948708d GR |
1393 | if (data->flags & LM90_HAVE_EMERGENCY) { |
1394 | err = sysfs_create_group(&new_client->dev.kobj, | |
1395 | &lm90_emergency_group); | |
1396 | if (err) | |
1397 | goto exit_remove_files; | |
1398 | } | |
06e1c0a2 GR |
1399 | if (data->flags & LM90_HAVE_EMERGENCY_ALARM) { |
1400 | err = sysfs_create_group(&new_client->dev.kobj, | |
1401 | &lm90_emergency_alarm_group); | |
1402 | if (err) | |
1403 | goto exit_remove_files; | |
1404 | } | |
1405 | if (data->flags & LM90_HAVE_TEMP3) { | |
1406 | err = sysfs_create_group(&new_client->dev.kobj, | |
1407 | &lm90_temp3_group); | |
1408 | if (err) | |
1409 | goto exit_remove_files; | |
1410 | } | |
0e39e01c | 1411 | |
1beeffe4 TJ |
1412 | data->hwmon_dev = hwmon_device_register(&new_client->dev); |
1413 | if (IS_ERR(data->hwmon_dev)) { | |
1414 | err = PTR_ERR(data->hwmon_dev); | |
0e39e01c | 1415 | goto exit_remove_files; |
943b0830 MH |
1416 | } |
1417 | ||
1da177e4 LT |
1418 | return 0; |
1419 | ||
0e39e01c | 1420 | exit_remove_files: |
b6fc1bac | 1421 | lm90_remove_files(new_client, data); |
1da177e4 LT |
1422 | exit_free: |
1423 | kfree(data); | |
1424 | exit: | |
1425 | return err; | |
1426 | } | |
1427 | ||
9b0e8526 | 1428 | static int lm90_remove(struct i2c_client *client) |
1da177e4 | 1429 | { |
943b0830 | 1430 | struct lm90_data *data = i2c_get_clientdata(client); |
1da177e4 | 1431 | |
1beeffe4 | 1432 | hwmon_device_unregister(data->hwmon_dev); |
b6fc1bac | 1433 | lm90_remove_files(client, data); |
943b0830 | 1434 | |
95238364 | 1435 | /* Restore initial configuration */ |
0c01b644 GR |
1436 | i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE, |
1437 | data->convrate_orig); | |
95238364 JD |
1438 | i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, |
1439 | data->config_orig); | |
1440 | ||
943b0830 | 1441 | kfree(data); |
1da177e4 LT |
1442 | return 0; |
1443 | } | |
1444 | ||
53de3342 JD |
1445 | static void lm90_alert(struct i2c_client *client, unsigned int flag) |
1446 | { | |
1447 | struct lm90_data *data = i2c_get_clientdata(client); | |
06e1c0a2 | 1448 | u8 config, alarms, alarms2 = 0; |
53de3342 JD |
1449 | |
1450 | lm90_read_reg(client, LM90_REG_R_STATUS, &alarms); | |
06e1c0a2 GR |
1451 | |
1452 | if (data->kind == max6696) | |
1453 | lm90_read_reg(client, MAX6696_REG_R_STATUS2, &alarms2); | |
1454 | ||
1455 | if ((alarms & 0x7f) == 0 && (alarms2 & 0xfe) == 0) { | |
53de3342 JD |
1456 | dev_info(&client->dev, "Everything OK\n"); |
1457 | } else { | |
1458 | if (alarms & 0x61) | |
1459 | dev_warn(&client->dev, | |
1460 | "temp%d out of range, please check!\n", 1); | |
1461 | if (alarms & 0x1a) | |
1462 | dev_warn(&client->dev, | |
1463 | "temp%d out of range, please check!\n", 2); | |
1464 | if (alarms & 0x04) | |
1465 | dev_warn(&client->dev, | |
1466 | "temp%d diode open, please check!\n", 2); | |
1467 | ||
06e1c0a2 GR |
1468 | if (alarms2 & 0x18) |
1469 | dev_warn(&client->dev, | |
1470 | "temp%d out of range, please check!\n", 3); | |
1471 | ||
53de3342 JD |
1472 | /* Disable ALERT# output, because these chips don't implement |
1473 | SMBus alert correctly; they should only hold the alert line | |
1474 | low briefly. */ | |
1179324c | 1475 | if ((data->flags & LM90_HAVE_BROKEN_ALERT) |
53de3342 JD |
1476 | && (alarms & data->alert_alarms)) { |
1477 | dev_dbg(&client->dev, "Disabling ALERT#\n"); | |
1478 | lm90_read_reg(client, LM90_REG_R_CONFIG1, &config); | |
1479 | i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, | |
1480 | config | 0x80); | |
1481 | } | |
1482 | } | |
1483 | } | |
1484 | ||
15b66ab6 GR |
1485 | static struct i2c_driver lm90_driver = { |
1486 | .class = I2C_CLASS_HWMON, | |
1487 | .driver = { | |
1488 | .name = "lm90", | |
1489 | }, | |
1490 | .probe = lm90_probe, | |
1491 | .remove = lm90_remove, | |
1492 | .alert = lm90_alert, | |
1493 | .id_table = lm90_id, | |
1494 | .detect = lm90_detect, | |
1495 | .address_list = normal_i2c, | |
1496 | }; | |
1da177e4 LT |
1497 | |
1498 | static int __init sensors_lm90_init(void) | |
1499 | { | |
1500 | return i2c_add_driver(&lm90_driver); | |
1501 | } | |
1502 | ||
1503 | static void __exit sensors_lm90_exit(void) | |
1504 | { | |
1505 | i2c_del_driver(&lm90_driver); | |
1506 | } | |
1507 | ||
1508 | MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>"); | |
1509 | MODULE_DESCRIPTION("LM90/ADM1032 driver"); | |
1510 | MODULE_LICENSE("GPL"); | |
1511 | ||
1512 | module_init(sensors_lm90_init); | |
1513 | module_exit(sensors_lm90_exit); |