[mirror_ubuntu-kernels.git] / drivers / ide / ht6560b.c

/*
 *  Copyright (C) 1995-2000  Linus Torvalds & author (see below)
 */

/*
 *  HT-6560B EIDE-controller support
 *  To activate controller support use kernel parameter "ide0=ht6560b".
 *  Use hdparm utility to enable PIO mode support.
 *
 *  Author:    Mikko Ala-Fossi            <maf@iki.fi>
 *             Jan Evert van Grootheest   <j.e.van.grootheest@caiway.nl>
 *
 *  Try:  http://www.maf.iki.fi/~maf/ht6560b/
 */

#define DRV_NAME	"ht6560b"
#define HT6560B_VERSION "v0.08"

#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/delay.h>
#include <linux/timer.h>
#include <linux/mm.h>
#include <linux/ioport.h>
#include <linux/blkdev.h>
#include <linux/ide.h>
#include <linux/init.h>

#include <asm/io.h>

/* #define DEBUG */  /* remove comments for DEBUG messages */

/*
 * The special i/o-port that HT-6560B uses to configuration:
 *    bit0 (0x01): "1" selects secondary interface
 *    bit2 (0x04): "1" enables FIFO function
 *    bit5 (0x20): "1" enables prefetched data read function  (???)
 *
 * The special i/o-port that HT-6560A uses to configuration:
 *    bit0 (0x01): "1" selects secondary interface
 *    bit1 (0x02): "1" enables prefetched data read function
 *    bit2 (0x04): "0" enables multi-master system	      (?)
 *    bit3 (0x08): "1" 3 cycle time, "0" 2 cycle time	      (?)
 */
#define HT_CONFIG_PORT	  0x3e6
#define HT_CONFIG(drivea) (u8)(((drivea)->drive_data & 0xff00) >> 8)
/*
 * FIFO + PREFETCH (both a/b-model)
 */
#define HT_CONFIG_DEFAULT 0x1c /* no prefetch */
/* #define HT_CONFIG_DEFAULT 0x3c */ /* with prefetch */
#define HT_SECONDARY_IF	  0x01
#define HT_PREFETCH_MODE  0x20

/*
 * ht6560b Timing values:
 *
 * I reviewed some assembler source listings of htide drivers and found
 * out how they setup those cycle time interfacing values, as they at Holtek
 * call them. IDESETUP.COM that is supplied with the drivers figures out
 * optimal values and fetches those values to drivers. I found out that
 * they use Select register to fetch timings to the ide board right after
 * interface switching. After that it was quite easy to add code to
 * ht6560b.c.
 *
 * IDESETUP.COM gave me values 0x24, 0x45, 0xaa, 0xff that worked fine
 * for hda and hdc. But hdb needed higher values to work, so I guess
 * that sometimes it is necessary to give higher value than IDESETUP
 * gives.   [see cmd640.c for an extreme example of this. -ml]
 *
 * Perhaps I should explain something about these timing values:
 * The higher nibble of value is the Recovery Time  (rt) and the lower nibble
 * of the value is the Active Time  (at). Minimum value 2 is the fastest and
 * the maximum value 15 is the slowest. Default values should be 15 for both.
 * So 0x24 means 2 for rt and 4 for at. Each of the drives should have
 * both values, and IDESETUP gives automatically rt=15 st=15 for CDROMs or
 * similar. If value is too small there will be all sorts of failures.
 *
 * Timing byte consists of
 *	High nibble:  Recovery Cycle Time  (rt)
 *	     The valid values range from 2 to 15. The default is 15.
 *
 *	Low nibble:   Active Cycle Time	   (at)
 *	     The valid values range from 2 to 15. The default is 15.
 *
 * You can obtain optimized timing values by running Holtek IDESETUP.COM
 * for DOS. DOS drivers get their timing values from command line, where
 * the first value is the Recovery Time and the second value is the
 * Active Time for each drive. Smaller value gives higher speed.
 * In case of failures you should probably fall back to a higher value.
 */
#define HT_TIMING(drivea) (u8)((drivea)->drive_data & 0x00ff)
#define HT_TIMING_DEFAULT 0xff

/*
 * This routine handles interface switching for the peculiar hardware design
 * on the F.G.I./Holtek HT-6560B VLB IDE interface.
 * The HT-6560B can only enable one IDE port at a time, and requires a
 * silly sequence (below) whenever we switch between primary and secondary.
 */

/*
 * This routine is invoked from ide.c to prepare for access to a given drive.
 */
static void ht6560b_selectproc (ide_drive_t *drive)
{
	ide_hwif_t *hwif = drive->hwif;
	unsigned long flags;
	static u8 current_select = 0;
	static u8 current_timing = 0;
	u8 select, timing;
	
	local_irq_save(flags);

	select = HT_CONFIG(drive);
	timing = HT_TIMING(drive);

	/*
	 * Need to enforce prefetch sometimes because otherwise
	 * it'll hang (hard).
	 */
	if (drive->media != ide_disk ||
	    (drive->dev_flags & IDE_DFLAG_PRESENT) == 0)
		select |= HT_PREFETCH_MODE;

	if (select != current_select || timing != current_timing) {
		current_select = select;
		current_timing = timing;
		(void)inb(HT_CONFIG_PORT);
		(void)inb(HT_CONFIG_PORT);
		(void)inb(HT_CONFIG_PORT);
		(void)inb(HT_CONFIG_PORT);
		outb(select, HT_CONFIG_PORT);
		/*
		 * Set timing for this drive:
		 */
		outb(timing, hwif->io_ports.device_addr);
		(void)inb(hwif->io_ports.status_addr);
#ifdef DEBUG
		printk("ht6560b: %s: select=%#x timing=%#x\n",
			drive->name, select, timing);
#endif
	}
	local_irq_restore(flags);
}

/*
 * Autodetection and initialization of ht6560b
 */
static int __init try_to_init_ht6560b(void)
{
	u8 orig_value;
	int i;
	
	/* Autodetect ht6560b */
	if ((orig_value = inb(HT_CONFIG_PORT)) == 0xff)
		return 0;
	
	for (i=3;i>0;i--) {
		outb(0x00, HT_CONFIG_PORT);
		if (!( (~inb(HT_CONFIG_PORT)) & 0x3f )) {
			outb(orig_value, HT_CONFIG_PORT);
			return 0;
		}
	}
	outb(0x00, HT_CONFIG_PORT);
	if ((~inb(HT_CONFIG_PORT))& 0x3f) {
		outb(orig_value, HT_CONFIG_PORT);
		return 0;
	}
	/*
	 * Ht6560b autodetected
	 */
	outb(HT_CONFIG_DEFAULT, HT_CONFIG_PORT);
	outb(HT_TIMING_DEFAULT, 0x1f6);	/* Select register */
	(void)inb(0x1f7);		/* Status register */

	printk("ht6560b " HT6560B_VERSION
	       ": chipset detected and initialized"
#ifdef DEBUG
	       " with debug enabled"
#endif
	       "\n"
		);
	return 1;
}

static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
{
	int active_time, recovery_time;
	int active_cycles, recovery_cycles;
	int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;

        if (pio) {
		unsigned int cycle_time;
		struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);

		cycle_time = ide_pio_cycle_time(drive, pio);

		/*
		 *  Just like opti621.c we try to calculate the
		 *  actual cycle time for recovery and activity
		 *  according system bus speed.
		 */
		active_time = t->active;
		recovery_time = cycle_time - active_time - t->setup;
		/*
		 *  Cycle times should be Vesa bus cycles
		 */
		active_cycles   = (active_time   * bus_speed + 999) / 1000;
		recovery_cycles = (recovery_time * bus_speed + 999) / 1000;
		/*
		 *  Upper and lower limits
		 */
		if (active_cycles   < 2)  active_cycles   = 2;
		if (recovery_cycles < 2)  recovery_cycles = 2;
		if (active_cycles   > 15) active_cycles   = 15;
		if (recovery_cycles > 15) recovery_cycles = 0;  /* 0==16 */
		
#ifdef DEBUG
		printk("ht6560b: drive %s setting pio=%d recovery=%d (%dns) active=%d (%dns)\n", drive->name, pio, recovery_cycles, recovery_time, active_cycles, active_time);
#endif
		
		return (u8)((recovery_cycles << 4) | active_cycles);
	} else {
		
#ifdef DEBUG
		printk("ht6560b: drive %s setting pio=0\n", drive->name);
#endif
		
		return HT_TIMING_DEFAULT;    /* default setting */
	}
}

static DEFINE_SPINLOCK(ht6560b_lock);

/*
 *  Enable/Disable so called prefetch mode
 */
static void ht_set_prefetch(ide_drive_t *drive, u8 state)
{
	unsigned long flags;
	int t = HT_PREFETCH_MODE << 8;

	spin_lock_irqsave(&ht6560b_lock, flags);

	/*
	 *  Prefetch mode and unmask irq seems to conflict
	 */
	if (state) {
		drive->drive_data |= t;   /* enable prefetch mode */
		drive->dev_flags |= IDE_DFLAG_NO_UNMASK;
		drive->dev_flags &= ~IDE_DFLAG_UNMASK;
	} else {
		drive->drive_data &= ~t;  /* disable prefetch mode */
		drive->dev_flags &= ~IDE_DFLAG_NO_UNMASK;
	}

	spin_unlock_irqrestore(&ht6560b_lock, flags);

#ifdef DEBUG
	printk("ht6560b: drive %s prefetch mode %sabled\n", drive->name, (state ? "en" : "dis"));
#endif
}

static void ht6560b_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
	unsigned long flags;
	u8 timing;
	
	switch (pio) {
	case 8:         /* set prefetch off */
	case 9:         /* set prefetch on */
		ht_set_prefetch(drive, pio & 1);
		return;
	}

	timing = ht_pio2timings(drive, pio);

	spin_lock_irqsave(&ht6560b_lock, flags);
	drive->drive_data &= 0xff00;
	drive->drive_data |= timing;
	spin_unlock_irqrestore(&ht6560b_lock, flags);

#ifdef DEBUG
	printk("ht6560b: drive %s tuned to pio mode %#x timing=%#x\n", drive->name, pio, timing);
#endif
}

static void __init ht6560b_init_dev(ide_drive_t *drive)
{
	ide_hwif_t *hwif = drive->hwif;
	/* Setting default configurations for drives. */
	int t = (HT_CONFIG_DEFAULT << 8) | HT_TIMING_DEFAULT;

	if (hwif->channel)
		t |= (HT_SECONDARY_IF << 8);

	drive->drive_data = t;
}

static int probe_ht6560b;

module_param_named(probe, probe_ht6560b, bool, 0);
MODULE_PARM_DESC(probe, "probe for HT6560B chipset");

static const struct ide_port_ops ht6560b_port_ops = {
	.init_dev		= ht6560b_init_dev,
	.set_pio_mode		= ht6560b_set_pio_mode,
	.selectproc		= ht6560b_selectproc,
};

static const struct ide_port_info ht6560b_port_info __initdata = {
	.name			= DRV_NAME,
	.chipset		= ide_ht6560b,
	.port_ops		= &ht6560b_port_ops,
	.host_flags		= IDE_HFLAG_SERIALIZE | /* is this needed? */
				  IDE_HFLAG_NO_DMA |
				  IDE_HFLAG_ABUSE_PREFETCH,
	.pio_mask		= ATA_PIO4,
};

static int __init ht6560b_init(void)
{
	if (probe_ht6560b == 0)
		return -ENODEV;

	if (!request_region(HT_CONFIG_PORT, 1, DRV_NAME)) {
		printk(KERN_NOTICE "%s: HT_CONFIG_PORT not found\n",
			__func__);
		return -ENODEV;
	}

	if (!try_to_init_ht6560b()) {
		printk(KERN_NOTICE "%s: HBA not found\n", __func__);
		goto release_region;
	}

	return ide_legacy_device_add(&ht6560b_port_info, 0);

release_region:
	release_region(HT_CONFIG_PORT, 1);
	return -ENODEV;
}

module_init(ht6560b_init);

MODULE_AUTHOR("See Local File");
MODULE_DESCRIPTION("HT-6560B EIDE-controller support");
MODULE_LICENSE("GPL");
Commit	Line	Data
1da177e4	1	/*
1da177e4 LT	2	* Copyright (C) 1995-2000 Linus Torvalds & author (see below)
	3	*/
	4
	5	/*
1da177e4 LT	6	* HT-6560B EIDE-controller support
	7	* To activate controller support use kernel parameter "ide0=ht6560b".
	8	* Use hdparm utility to enable PIO mode support.
	9	*
	10	* Author: Mikko Ala-Fossi <maf@iki.fi>
eb34b2d9	11	* Jan Evert van Grootheest <j.e.van.grootheest@caiway.nl>
1da177e4 LT	12	*
	13	* Try: http://www.maf.iki.fi/~maf/ht6560b/
	14	*/
	15
2e4ed295	16	#define DRV_NAME "ht6560b"
0e7d8d48	17	#define HT6560B_VERSION "v0.08"
1da177e4	18
1da177e4	19	#include <linux/module.h>
1da177e4 LT	20	#include <linux/types.h>
	21	#include <linux/kernel.h>
	22	#include <linux/delay.h>
	23	#include <linux/timer.h>
	24	#include <linux/mm.h>
	25	#include <linux/ioport.h>
	26	#include <linux/blkdev.h>
1da177e4 LT	27	#include <linux/ide.h>
	28	#include <linux/init.h>
	29
	30	#include <asm/io.h>
	31
	32	/* #define DEBUG / / remove comments for DEBUG messages */
	33
	34	/*
	35	* The special i/o-port that HT-6560B uses to configuration:
	36	* bit0 (0x01): "1" selects secondary interface
	37	* bit2 (0x04): "1" enables FIFO function
	38	* bit5 (0x20): "1" enables prefetched data read function (???)
	39	*
	40	* The special i/o-port that HT-6560A uses to configuration:
	41	* bit0 (0x01): "1" selects secondary interface
	42	* bit1 (0x02): "1" enables prefetched data read function
	43	* bit2 (0x04): "0" enables multi-master system (?)
	44	* bit3 (0x08): "1" 3 cycle time, "0" 2 cycle time (?)
	45	*/
	46	#define HT_CONFIG_PORT 0x3e6
	47	#define HT_CONFIG(drivea) (u8)(((drivea)->drive_data & 0xff00) >> 8)
	48	/*
	49	* FIFO + PREFETCH (both a/b-model)
	50	*/
	51	#define HT_CONFIG_DEFAULT 0x1c /* no prefetch */
	52	/* #define HT_CONFIG_DEFAULT 0x3c / / with prefetch */
	53	#define HT_SECONDARY_IF 0x01
	54	#define HT_PREFETCH_MODE 0x20
	55
	56	/*
	57	* ht6560b Timing values:
	58	*
	59	* I reviewed some assembler source listings of htide drivers and found
	60	* out how they setup those cycle time interfacing values, as they at Holtek
	61	* call them. IDESETUP.COM that is supplied with the drivers figures out
	62	* optimal values and fetches those values to drivers. I found out that
23579a2a	63	* they use Select register to fetch timings to the ide board right after
1da177e4 LT	64	* interface switching. After that it was quite easy to add code to
	65	* ht6560b.c.
	66	*
	67	* IDESETUP.COM gave me values 0x24, 0x45, 0xaa, 0xff that worked fine
	68	* for hda and hdc. But hdb needed higher values to work, so I guess
	69	* that sometimes it is necessary to give higher value than IDESETUP
	70	* gives. [see cmd640.c for an extreme example of this. -ml]
	71	*
	72	* Perhaps I should explain something about these timing values:
	73	* The higher nibble of value is the Recovery Time (rt) and the lower nibble
	74	* of the value is the Active Time (at). Minimum value 2 is the fastest and
	75	* the maximum value 15 is the slowest. Default values should be 15 for both.
	76	* So 0x24 means 2 for rt and 4 for at. Each of the drives should have
	77	* both values, and IDESETUP gives automatically rt=15 st=15 for CDROMs or
	78	* similar. If value is too small there will be all sorts of failures.
	79	*
	80	* Timing byte consists of
	81	* High nibble: Recovery Cycle Time (rt)
	82	* The valid values range from 2 to 15. The default is 15.
	83	*
	84	* Low nibble: Active Cycle Time (at)
	85	* The valid values range from 2 to 15. The default is 15.
	86	*
	87	* You can obtain optimized timing values by running Holtek IDESETUP.COM
	88	* for DOS. DOS drivers get their timing values from command line, where
	89	* the first value is the Recovery Time and the second value is the
	90	* Active Time for each drive. Smaller value gives higher speed.
	91	* In case of failures you should probably fall back to a higher value.
	92	*/
	93	#define HT_TIMING(drivea) (u8)((drivea)->drive_data & 0x00ff)
	94	#define HT_TIMING_DEFAULT 0xff
	95
	96	/*
	97	* This routine handles interface switching for the peculiar hardware design
	98	* on the F.G.I./Holtek HT-6560B VLB IDE interface.
	99	* The HT-6560B can only enable one IDE port at a time, and requires a
	100	* silly sequence (below) whenever we switch between primary and secondary.
	101	*/
	102
	103	/*
	104	* This routine is invoked from ide.c to prepare for access to a given drive.
	105	*/
	106	static void ht6560b_selectproc (ide_drive_t *drive)
	107	{
23579a2a	108	ide_hwif_t *hwif = drive->hwif;
1da177e4 LT	109	unsigned long flags;
	110	static u8 current_select = 0;
	111	static u8 current_timing = 0;
	112	u8 select, timing;
	113
	114	local_irq_save(flags);
0e7d8d48	115
1da177e4 LT	116	select = HT_CONFIG(drive);
1da177e4 LT	117	timing = HT_TIMING(drive);
0e7d8d48 JEG	118
	119	/*
	120	* Need to enforce prefetch sometimes because otherwise
	121	* it'll hang (hard).
	122	*/
97100fc8 BZ	123	if (drive->media != ide_disk \|\|
97100fc8 BZ	124	(drive->dev_flags & IDE_DFLAG_PRESENT) == 0)
0e7d8d48 JEG	125	select \|= HT_PREFETCH_MODE;
0e7d8d48 JEG	126
1da177e4 LT	127	if (select != current_select \|\| timing != current_timing) {
	128	current_select = select;
	129	current_timing = timing;
0ecdca26 BZ	130	(void)inb(HT_CONFIG_PORT);
	131	(void)inb(HT_CONFIG_PORT);
	132	(void)inb(HT_CONFIG_PORT);
	133	(void)inb(HT_CONFIG_PORT);
	134	outb(select, HT_CONFIG_PORT);
1da177e4 LT	135	/*
	136	* Set timing for this drive:
	137	*/
4c3032d8 BZ	138	outb(timing, hwif->io_ports.device_addr);
4c3032d8 BZ	139	(void)inb(hwif->io_ports.status_addr);
1da177e4 LT	140	#ifdef DEBUG
	141	printk("ht6560b: %s: select=%#x timing=%#x\n",
	142	drive->name, select, timing);
	143	#endif
	144	}
	145	local_irq_restore(flags);
	146	}
	147
	148	/*
	149	* Autodetection and initialization of ht6560b
	150	*/
	151	static int __init try_to_init_ht6560b(void)
	152	{
	153	u8 orig_value;
	154	int i;
	155
	156	/* Autodetect ht6560b */
	157	if ((orig_value = inb(HT_CONFIG_PORT)) == 0xff)
	158	return 0;
	159
	160	for (i=3;i>0;i--) {
	161	outb(0x00, HT_CONFIG_PORT);
	162	if (!( (~inb(HT_CONFIG_PORT)) & 0x3f )) {
	163	outb(orig_value, HT_CONFIG_PORT);
	164	return 0;
	165	}
	166	}
	167	outb(0x00, HT_CONFIG_PORT);
	168	if ((~inb(HT_CONFIG_PORT))& 0x3f) {
	169	outb(orig_value, HT_CONFIG_PORT);
	170	return 0;
	171	}
	172	/*
	173	* Ht6560b autodetected
	174	*/
	175	outb(HT_CONFIG_DEFAULT, HT_CONFIG_PORT);
23579a2a BZ	176	outb(HT_TIMING_DEFAULT, 0x1f6); /* Select register */
	177	(void)inb(0x1f7); /* Status register */
	178
0e7d8d48	179	printk("ht6560b " HT6560B_VERSION
1da177e4 LT	180	": chipset detected and initialized"
	181	#ifdef DEBUG
	182	" with debug enabled"
	183	#endif
0e7d8d48	184	"\n"
1da177e4 LT	185	);
	186	return 1;
	187	}
	188
26bcb879	189	static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
1da177e4 LT	190	{
	191	int active_time, recovery_time;
	192	int active_cycles, recovery_cycles;
30e5ee4d	193	int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
ebae41a5	194
1da177e4	195	if (pio) {
7dd00083	196	unsigned int cycle_time;
b32b76f7	197	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
7dd00083	198
7dd00083 BZ	199	cycle_time = ide_pio_cycle_time(drive, pio);
7dd00083 BZ	200
1da177e4 LT	201	/*
	202	* Just like opti621.c we try to calculate the
	203	* actual cycle time for recovery and activity
	204	* according system bus speed.
	205	*/
b32b76f7 BZ	206	active_time = t->active;
b32b76f7 BZ	207	recovery_time = cycle_time - active_time - t->setup;
1da177e4 LT	208	/*
	209	* Cycle times should be Vesa bus cycles
	210	*/
	211	active_cycles = (active_time * bus_speed + 999) / 1000;
	212	recovery_cycles = (recovery_time * bus_speed + 999) / 1000;
	213	/*
	214	* Upper and lower limits
	215	*/
	216	if (active_cycles < 2) active_cycles = 2;
	217	if (recovery_cycles < 2) recovery_cycles = 2;
	218	if (active_cycles > 15) active_cycles = 15;
	219	if (recovery_cycles > 15) recovery_cycles = 0; /* 0==16 */
	220
	221	#ifdef DEBUG
	222	printk("ht6560b: drive %s setting pio=%d recovery=%d (%dns) active=%d (%dns)\n", drive->name, pio, recovery_cycles, recovery_time, active_cycles, active_time);
	223	#endif
	224
	225	return (u8)((recovery_cycles << 4) \| active_cycles);
	226	} else {
	227
	228	#ifdef DEBUG
	229	printk("ht6560b: drive %s setting pio=0\n", drive->name);
	230	#endif
	231
	232	return HT_TIMING_DEFAULT; /* default setting */
	233	}
	234	}
	235
69e88d2a BZ	236	static DEFINE_SPINLOCK(ht6560b_lock);
69e88d2a BZ	237
1da177e4 LT	238	/*
	239	* Enable/Disable so called prefetch mode
	240	*/
	241	static void ht_set_prefetch(ide_drive_t *drive, u8 state)
	242	{
	243	unsigned long flags;
	244	int t = HT_PREFETCH_MODE << 8;
69e88d2a BZ	245
	246	spin_lock_irqsave(&ht6560b_lock, flags);
	247
1da177e4 LT	248	/*
	249	* Prefetch mode and unmask irq seems to conflict
	250	*/
	251	if (state) {
	252	drive->drive_data \|= t; /* enable prefetch mode */
97100fc8 BZ	253	drive->dev_flags \|= IDE_DFLAG_NO_UNMASK;
97100fc8 BZ	254	drive->dev_flags &= ~IDE_DFLAG_UNMASK;
1da177e4 LT	255	} else {
1da177e4 LT	256	drive->drive_data &= ~t; /* disable prefetch mode */
97100fc8	257	drive->dev_flags &= ~IDE_DFLAG_NO_UNMASK;
1da177e4	258	}
69e88d2a BZ	259
	260	spin_unlock_irqrestore(&ht6560b_lock, flags);
	261
1da177e4 LT	262	#ifdef DEBUG
	263	printk("ht6560b: drive %s prefetch mode %sabled\n", drive->name, (state ? "en" : "dis"));
	264	#endif
	265	}
	266
26bcb879	267	static void ht6560b_set_pio_mode(ide_drive_t *drive, const u8 pio)
1da177e4 LT	268	{
	269	unsigned long flags;
	270	u8 timing;
	271
	272	switch (pio) {
	273	case 8: /* set prefetch off */
	274	case 9: /* set prefetch on */
	275	ht_set_prefetch(drive, pio & 1);
	276	return;
	277	}
69e88d2a	278
1da177e4	279	timing = ht_pio2timings(drive, pio);
69e88d2a BZ	280
69e88d2a BZ	281	spin_lock_irqsave(&ht6560b_lock, flags);
1da177e4 LT	282	drive->drive_data &= 0xff00;
1da177e4 LT	283	drive->drive_data \|= timing;
69e88d2a BZ	284	spin_unlock_irqrestore(&ht6560b_lock, flags);
69e88d2a BZ	285
1da177e4 LT	286	#ifdef DEBUG
	287	printk("ht6560b: drive %s tuned to pio mode %#x timing=%#x\n", drive->name, pio, timing);
	288	#endif
	289	}
	290
e6d95bd1	291	static void __init ht6560b_init_dev(ide_drive_t *drive)
1f2cf8b0	292	{
e6d95bd1	293	ide_hwif_t *hwif = drive->hwif;
1f2cf8b0 BZ	294	/* Setting default configurations for drives. */
	295	int t = (HT_CONFIG_DEFAULT << 8) \| HT_TIMING_DEFAULT;
	296
	297	if (hwif->channel)
	298	t \|= (HT_SECONDARY_IF << 8);
	299
e6d95bd1	300	drive->drive_data = t;
1f2cf8b0 BZ	301	}
1f2cf8b0 BZ	302
ef87f8d0	303	static int probe_ht6560b;
84913882 BZ	304
	305	module_param_named(probe, probe_ht6560b, bool, 0);
	306	MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
	307
ac95beed	308	static const struct ide_port_ops ht6560b_port_ops = {
e6d95bd1	309	.init_dev = ht6560b_init_dev,
ac95beed BZ	310	.set_pio_mode = ht6560b_set_pio_mode,
	311	.selectproc = ht6560b_selectproc,
	312	};
	313
c413b9b9	314	static const struct ide_port_info ht6560b_port_info __initdata = {
d92f1a28	315	.name = DRV_NAME,
c413b9b9	316	.chipset = ide_ht6560b,
ac95beed	317	.port_ops = &ht6560b_port_ops,
c413b9b9 BZ	318	.host_flags = IDE_HFLAG_SERIALIZE \| /* is this needed? */
c413b9b9 BZ	319	IDE_HFLAG_NO_DMA \|
c413b9b9	320	IDE_HFLAG_ABUSE_PREFETCH,
1a1990f5	321	.pio_mask = ATA_PIO4,
c413b9b9 BZ	322	};
c413b9b9 BZ	323
ade2daf9	324	static int __init ht6560b_init(void)
1da177e4	325	{
84913882 BZ	326	if (probe_ht6560b == 0)
	327	return -ENODEV;
	328
2e4ed295	329	if (!request_region(HT_CONFIG_PORT, 1, DRV_NAME)) {
1da177e4	330	printk(KERN_NOTICE "%s: HT_CONFIG_PORT not found\n",
eb63963a	331	__func__);
1da177e4 LT	332	return -ENODEV;
	333	}
	334
	335	if (!try_to_init_ht6560b()) {
eb63963a	336	printk(KERN_NOTICE "%s: HBA not found\n", __func__);
1da177e4 LT	337	goto release_region;
	338	}
	339
0bfeee7d	340	return ide_legacy_device_add(&ht6560b_port_info, 0);
1da177e4 LT	341
	342	release_region:
	343	release_region(HT_CONFIG_PORT, 1);
	344	return -ENODEV;
	345	}
	346
1da177e4	347	module_init(ht6560b_init);
1da177e4 LT	348
	349	MODULE_AUTHOR("See Local File");
	350	MODULE_DESCRIPTION("HT-6560B EIDE-controller support");
	351	MODULE_LICENSE("GPL");