]>
Commit | Line | Data |
---|---|---|
1da177e4 | 1 | /* |
96dcc08b | 2 | * linux/drivers/ide/pci/hpt366.c Version 1.06 Jun 27, 2007 |
1da177e4 LT |
3 | * |
4 | * Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org> | |
5 | * Portions Copyright (C) 2001 Sun Microsystems, Inc. | |
6 | * Portions Copyright (C) 2003 Red Hat Inc | |
38b66f84 | 7 | * Portions Copyright (C) 2005-2007 MontaVista Software, Inc. |
1da177e4 LT |
8 | * |
9 | * Thanks to HighPoint Technologies for their assistance, and hardware. | |
10 | * Special Thanks to Jon Burchmore in SanDiego for the deep pockets, his | |
11 | * donation of an ABit BP6 mainboard, processor, and memory acellerated | |
12 | * development and support. | |
13 | * | |
b39b01ff | 14 | * |
836c0063 SS |
15 | * HighPoint has its own drivers (open source except for the RAID part) |
16 | * available from http://www.highpoint-tech.com/BIOS%20+%20Driver/. | |
17 | * This may be useful to anyone wanting to work on this driver, however do not | |
18 | * trust them too much since the code tends to become less and less meaningful | |
19 | * as the time passes... :-/ | |
b39b01ff | 20 | * |
1da177e4 LT |
21 | * Note that final HPT370 support was done by force extraction of GPL. |
22 | * | |
23 | * - add function for getting/setting power status of drive | |
24 | * - the HPT370's state machine can get confused. reset it before each dma | |
25 | * xfer to prevent that from happening. | |
26 | * - reset state engine whenever we get an error. | |
27 | * - check for busmaster state at end of dma. | |
28 | * - use new highpoint timings. | |
29 | * - detect bus speed using highpoint register. | |
30 | * - use pll if we don't have a clock table. added a 66MHz table that's | |
31 | * just 2x the 33MHz table. | |
32 | * - removed turnaround. NOTE: we never want to switch between pll and | |
33 | * pci clocks as the chip can glitch in those cases. the highpoint | |
34 | * approved workaround slows everything down too much to be useful. in | |
35 | * addition, we would have to serialize access to each chip. | |
36 | * Adrian Sun <a.sun@sun.com> | |
37 | * | |
38 | * add drive timings for 66MHz PCI bus, | |
39 | * fix ATA Cable signal detection, fix incorrect /proc info | |
40 | * add /proc display for per-drive PIO/DMA/UDMA mode and | |
41 | * per-channel ATA-33/66 Cable detect. | |
42 | * Duncan Laurie <void@sun.com> | |
43 | * | |
44 | * fixup /proc output for multiple controllers | |
45 | * Tim Hockin <thockin@sun.com> | |
46 | * | |
47 | * On hpt366: | |
48 | * Reset the hpt366 on error, reset on dma | |
49 | * Fix disabling Fast Interrupt hpt366. | |
50 | * Mike Waychison <crlf@sun.com> | |
51 | * | |
52 | * Added support for 372N clocking and clock switching. The 372N needs | |
53 | * different clocks on read/write. This requires overloading rw_disk and | |
54 | * other deeply crazy things. Thanks to <http://www.hoerstreich.de> for | |
55 | * keeping me sane. | |
56 | * Alan Cox <alan@redhat.com> | |
57 | * | |
836c0063 SS |
58 | * - fix the clock turnaround code: it was writing to the wrong ports when |
59 | * called for the secondary channel, caching the current clock mode per- | |
60 | * channel caused the cached register value to get out of sync with the | |
61 | * actual one, the channels weren't serialized, the turnaround shouldn't | |
62 | * be done on 66 MHz PCI bus | |
7b73ee05 SS |
63 | * - disable UltraATA/100 for HPT370 by default as the 33 MHz clock being used |
64 | * does not allow for this speed anyway | |
65 | * - avoid touching disabled channels (e.g. HPT371/N are single channel chips, | |
66 | * their primary channel is kind of virtual, it isn't tied to any pins) | |
471a0bda SS |
67 | * - fix/remove bad/unused timing tables and use one set of tables for the whole |
68 | * HPT37x chip family; save space by introducing the separate transfer mode | |
69 | * table in which the mode lookup is done | |
26c068da SS |
70 | * - use f_CNT value saved by the HighPoint BIOS as reading it directly gives |
71 | * the wrong PCI frequency since DPLL has already been calibrated by BIOS | |
33b18a60 SS |
72 | * - fix the hotswap code: it caused RESET- to glitch when tristating the bus, |
73 | * and for HPT36x the obsolete HDIO_TRISTATE_HWIF handler was called instead | |
73d1dd93 SS |
74 | * - pass to init_chipset() handlers a copy of the IDE PCI device structure as |
75 | * they tamper with its fields | |
7b73ee05 SS |
76 | * - pass to the init_setup handlers a copy of the ide_pci_device_t structure |
77 | * since they may tamper with its fields | |
90778574 SS |
78 | * - prefix the driver startup messages with the real chip name |
79 | * - claim the extra 240 bytes of I/O space for all chips | |
e139b0b0 | 80 | * - optimize the rate masking/filtering and the drive list lookup code |
b4586715 | 81 | * - use pci_get_slot() to get to the function 1 of HPT36x/374 |
7b73ee05 SS |
82 | * - cache offset of the channel's misc. control registers (MCRs) being used |
83 | * throughout the driver | |
84 | * - only touch the relevant MCR when detecting the cable type on HPT374's | |
85 | * function 1 | |
abc4ad4c | 86 | * - rename all the register related variables consistently |
7b73ee05 SS |
87 | * - move all the interrupt twiddling code from the speedproc handlers into |
88 | * init_hwif_hpt366(), also grouping all the DMA related code together there | |
89 | * - merge two HPT37x speedproc handlers, fix the PIO timing register mask and | |
90 | * separate the UltraDMA and MWDMA masks there to avoid changing PIO timings | |
91 | * when setting an UltraDMA mode | |
92 | * - fix hpt3xx_tune_drive() to set the PIO mode requested, not always select | |
93 | * the best possible one | |
4bf63de2 | 94 | * - clean up DMA timeout handling for HPT370 |
7b73ee05 SS |
95 | * - switch to using the enumeration type to differ between the numerous chip |
96 | * variants, matching PCI device/revision ID with the chip type early, at the | |
97 | * init_setup stage | |
98 | * - extend the hpt_info structure to hold the DPLL and PCI clock frequencies, | |
99 | * stop duplicating it for each channel by storing the pointer in the pci_dev | |
100 | * structure: first, at the init_setup stage, point it to a static "template" | |
101 | * with only the chip type and its specific base DPLL frequency, the highest | |
102 | * supported DMA mode, and the chip settings table pointer filled, then, at | |
103 | * the init_chipset stage, allocate per-chip instance and fill it with the | |
104 | * rest of the necessary information | |
105 | * - get rid of the constant thresholds in the HPT37x PCI clock detection code, | |
106 | * switch to calculating PCI clock frequency based on the chip's base DPLL | |
107 | * frequency | |
108 | * - switch to using the DPLL clock and enable UltraATA/133 mode by default on | |
278978e9 SS |
109 | * anything newer than HPT370/A (except HPT374 that is not capable of this |
110 | * mode according to the manual) | |
6273d26a SS |
111 | * - fold PCI clock detection and DPLL setup code into init_chipset_hpt366(), |
112 | * also fixing the interchanged 25/40 MHz PCI clock cases for HPT36x chips; | |
7b73ee05 SS |
113 | * unify HPT36x/37x timing setup code and the speedproc handlers by joining |
114 | * the register setting lists into the table indexed by the clock selected | |
115 | * Sergei Shtylyov, <sshtylyov@ru.mvista.com> or <source@mvista.com> | |
1da177e4 LT |
116 | */ |
117 | ||
1da177e4 LT |
118 | #include <linux/types.h> |
119 | #include <linux/module.h> | |
120 | #include <linux/kernel.h> | |
121 | #include <linux/delay.h> | |
122 | #include <linux/timer.h> | |
123 | #include <linux/mm.h> | |
124 | #include <linux/ioport.h> | |
125 | #include <linux/blkdev.h> | |
126 | #include <linux/hdreg.h> | |
127 | ||
128 | #include <linux/interrupt.h> | |
129 | #include <linux/pci.h> | |
130 | #include <linux/init.h> | |
131 | #include <linux/ide.h> | |
132 | ||
133 | #include <asm/uaccess.h> | |
134 | #include <asm/io.h> | |
135 | #include <asm/irq.h> | |
136 | ||
137 | /* various tuning parameters */ | |
138 | #define HPT_RESET_STATE_ENGINE | |
836c0063 SS |
139 | #undef HPT_DELAY_INTERRUPT |
140 | #define HPT_SERIALIZE_IO 0 | |
1da177e4 LT |
141 | |
142 | static const char *quirk_drives[] = { | |
143 | "QUANTUM FIREBALLlct08 08", | |
144 | "QUANTUM FIREBALLP KA6.4", | |
145 | "QUANTUM FIREBALLP LM20.4", | |
146 | "QUANTUM FIREBALLP LM20.5", | |
147 | NULL | |
148 | }; | |
149 | ||
150 | static const char *bad_ata100_5[] = { | |
151 | "IBM-DTLA-307075", | |
152 | "IBM-DTLA-307060", | |
153 | "IBM-DTLA-307045", | |
154 | "IBM-DTLA-307030", | |
155 | "IBM-DTLA-307020", | |
156 | "IBM-DTLA-307015", | |
157 | "IBM-DTLA-305040", | |
158 | "IBM-DTLA-305030", | |
159 | "IBM-DTLA-305020", | |
160 | "IC35L010AVER07-0", | |
161 | "IC35L020AVER07-0", | |
162 | "IC35L030AVER07-0", | |
163 | "IC35L040AVER07-0", | |
164 | "IC35L060AVER07-0", | |
165 | "WDC AC310200R", | |
166 | NULL | |
167 | }; | |
168 | ||
169 | static const char *bad_ata66_4[] = { | |
170 | "IBM-DTLA-307075", | |
171 | "IBM-DTLA-307060", | |
172 | "IBM-DTLA-307045", | |
173 | "IBM-DTLA-307030", | |
174 | "IBM-DTLA-307020", | |
175 | "IBM-DTLA-307015", | |
176 | "IBM-DTLA-305040", | |
177 | "IBM-DTLA-305030", | |
178 | "IBM-DTLA-305020", | |
179 | "IC35L010AVER07-0", | |
180 | "IC35L020AVER07-0", | |
181 | "IC35L030AVER07-0", | |
182 | "IC35L040AVER07-0", | |
183 | "IC35L060AVER07-0", | |
184 | "WDC AC310200R", | |
783353b1 | 185 | "MAXTOR STM3320620A", |
1da177e4 LT |
186 | NULL |
187 | }; | |
188 | ||
189 | static const char *bad_ata66_3[] = { | |
190 | "WDC AC310200R", | |
191 | NULL | |
192 | }; | |
193 | ||
194 | static const char *bad_ata33[] = { | |
195 | "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2", | |
196 | "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", | |
197 | "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", | |
198 | "Maxtor 90510D4", | |
199 | "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", | |
200 | "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", | |
201 | "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", | |
202 | NULL | |
203 | }; | |
204 | ||
471a0bda SS |
205 | static u8 xfer_speeds[] = { |
206 | XFER_UDMA_6, | |
207 | XFER_UDMA_5, | |
208 | XFER_UDMA_4, | |
209 | XFER_UDMA_3, | |
210 | XFER_UDMA_2, | |
211 | XFER_UDMA_1, | |
212 | XFER_UDMA_0, | |
213 | ||
214 | XFER_MW_DMA_2, | |
215 | XFER_MW_DMA_1, | |
216 | XFER_MW_DMA_0, | |
217 | ||
218 | XFER_PIO_4, | |
219 | XFER_PIO_3, | |
220 | XFER_PIO_2, | |
221 | XFER_PIO_1, | |
222 | XFER_PIO_0 | |
1da177e4 LT |
223 | }; |
224 | ||
471a0bda SS |
225 | /* Key for bus clock timings |
226 | * 36x 37x | |
227 | * bits bits | |
228 | * 0:3 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA. | |
229 | * cycles = value + 1 | |
230 | * 4:7 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA. | |
231 | * cycles = value + 1 | |
232 | * 8:11 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file | |
233 | * register access. | |
234 | * 12:15 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file | |
235 | * register access. | |
236 | * 16:18 18:20 udma_cycle_time. Clock cycles for UDMA xfer. | |
237 | * - 21 CLK frequency: 0=ATA clock, 1=dual ATA clock. | |
238 | * 19:21 22:24 pre_high_time. Time to initialize the 1st cycle for PIO and | |
239 | * MW DMA xfer. | |
240 | * 22:24 25:27 cmd_pre_high_time. Time to initialize the 1st PIO cycle for | |
241 | * task file register access. | |
242 | * 28 28 UDMA enable. | |
243 | * 29 29 DMA enable. | |
244 | * 30 30 PIO MST enable. If set, the chip is in bus master mode during | |
245 | * PIO xfer. | |
246 | * 31 31 FIFO enable. | |
1da177e4 | 247 | */ |
1da177e4 | 248 | |
471a0bda SS |
249 | static u32 forty_base_hpt36x[] = { |
250 | /* XFER_UDMA_6 */ 0x900fd943, | |
251 | /* XFER_UDMA_5 */ 0x900fd943, | |
252 | /* XFER_UDMA_4 */ 0x900fd943, | |
253 | /* XFER_UDMA_3 */ 0x900ad943, | |
254 | /* XFER_UDMA_2 */ 0x900bd943, | |
255 | /* XFER_UDMA_1 */ 0x9008d943, | |
256 | /* XFER_UDMA_0 */ 0x9008d943, | |
257 | ||
258 | /* XFER_MW_DMA_2 */ 0xa008d943, | |
259 | /* XFER_MW_DMA_1 */ 0xa010d955, | |
260 | /* XFER_MW_DMA_0 */ 0xa010d9fc, | |
261 | ||
262 | /* XFER_PIO_4 */ 0xc008d963, | |
263 | /* XFER_PIO_3 */ 0xc010d974, | |
264 | /* XFER_PIO_2 */ 0xc010d997, | |
265 | /* XFER_PIO_1 */ 0xc010d9c7, | |
266 | /* XFER_PIO_0 */ 0xc018d9d9 | |
1da177e4 LT |
267 | }; |
268 | ||
471a0bda SS |
269 | static u32 thirty_three_base_hpt36x[] = { |
270 | /* XFER_UDMA_6 */ 0x90c9a731, | |
271 | /* XFER_UDMA_5 */ 0x90c9a731, | |
272 | /* XFER_UDMA_4 */ 0x90c9a731, | |
273 | /* XFER_UDMA_3 */ 0x90cfa731, | |
274 | /* XFER_UDMA_2 */ 0x90caa731, | |
275 | /* XFER_UDMA_1 */ 0x90cba731, | |
276 | /* XFER_UDMA_0 */ 0x90c8a731, | |
277 | ||
278 | /* XFER_MW_DMA_2 */ 0xa0c8a731, | |
279 | /* XFER_MW_DMA_1 */ 0xa0c8a732, /* 0xa0c8a733 */ | |
280 | /* XFER_MW_DMA_0 */ 0xa0c8a797, | |
281 | ||
282 | /* XFER_PIO_4 */ 0xc0c8a731, | |
283 | /* XFER_PIO_3 */ 0xc0c8a742, | |
284 | /* XFER_PIO_2 */ 0xc0d0a753, | |
285 | /* XFER_PIO_1 */ 0xc0d0a7a3, /* 0xc0d0a793 */ | |
286 | /* XFER_PIO_0 */ 0xc0d0a7aa /* 0xc0d0a7a7 */ | |
1da177e4 LT |
287 | }; |
288 | ||
471a0bda SS |
289 | static u32 twenty_five_base_hpt36x[] = { |
290 | /* XFER_UDMA_6 */ 0x90c98521, | |
291 | /* XFER_UDMA_5 */ 0x90c98521, | |
292 | /* XFER_UDMA_4 */ 0x90c98521, | |
293 | /* XFER_UDMA_3 */ 0x90cf8521, | |
294 | /* XFER_UDMA_2 */ 0x90cf8521, | |
295 | /* XFER_UDMA_1 */ 0x90cb8521, | |
296 | /* XFER_UDMA_0 */ 0x90cb8521, | |
297 | ||
298 | /* XFER_MW_DMA_2 */ 0xa0ca8521, | |
299 | /* XFER_MW_DMA_1 */ 0xa0ca8532, | |
300 | /* XFER_MW_DMA_0 */ 0xa0ca8575, | |
301 | ||
302 | /* XFER_PIO_4 */ 0xc0ca8521, | |
303 | /* XFER_PIO_3 */ 0xc0ca8532, | |
304 | /* XFER_PIO_2 */ 0xc0ca8542, | |
305 | /* XFER_PIO_1 */ 0xc0d08572, | |
306 | /* XFER_PIO_0 */ 0xc0d08585 | |
1da177e4 LT |
307 | }; |
308 | ||
471a0bda SS |
309 | static u32 thirty_three_base_hpt37x[] = { |
310 | /* XFER_UDMA_6 */ 0x12446231, /* 0x12646231 ?? */ | |
311 | /* XFER_UDMA_5 */ 0x12446231, | |
312 | /* XFER_UDMA_4 */ 0x12446231, | |
313 | /* XFER_UDMA_3 */ 0x126c6231, | |
314 | /* XFER_UDMA_2 */ 0x12486231, | |
315 | /* XFER_UDMA_1 */ 0x124c6233, | |
316 | /* XFER_UDMA_0 */ 0x12506297, | |
317 | ||
318 | /* XFER_MW_DMA_2 */ 0x22406c31, | |
319 | /* XFER_MW_DMA_1 */ 0x22406c33, | |
320 | /* XFER_MW_DMA_0 */ 0x22406c97, | |
321 | ||
322 | /* XFER_PIO_4 */ 0x06414e31, | |
323 | /* XFER_PIO_3 */ 0x06414e42, | |
324 | /* XFER_PIO_2 */ 0x06414e53, | |
325 | /* XFER_PIO_1 */ 0x06814e93, | |
326 | /* XFER_PIO_0 */ 0x06814ea7 | |
1da177e4 LT |
327 | }; |
328 | ||
471a0bda SS |
329 | static u32 fifty_base_hpt37x[] = { |
330 | /* XFER_UDMA_6 */ 0x12848242, | |
331 | /* XFER_UDMA_5 */ 0x12848242, | |
332 | /* XFER_UDMA_4 */ 0x12ac8242, | |
333 | /* XFER_UDMA_3 */ 0x128c8242, | |
334 | /* XFER_UDMA_2 */ 0x120c8242, | |
335 | /* XFER_UDMA_1 */ 0x12148254, | |
336 | /* XFER_UDMA_0 */ 0x121882ea, | |
337 | ||
338 | /* XFER_MW_DMA_2 */ 0x22808242, | |
339 | /* XFER_MW_DMA_1 */ 0x22808254, | |
340 | /* XFER_MW_DMA_0 */ 0x228082ea, | |
341 | ||
342 | /* XFER_PIO_4 */ 0x0a81f442, | |
343 | /* XFER_PIO_3 */ 0x0a81f443, | |
344 | /* XFER_PIO_2 */ 0x0a81f454, | |
345 | /* XFER_PIO_1 */ 0x0ac1f465, | |
346 | /* XFER_PIO_0 */ 0x0ac1f48a | |
1da177e4 LT |
347 | }; |
348 | ||
471a0bda SS |
349 | static u32 sixty_six_base_hpt37x[] = { |
350 | /* XFER_UDMA_6 */ 0x1c869c62, | |
351 | /* XFER_UDMA_5 */ 0x1cae9c62, /* 0x1c8a9c62 */ | |
352 | /* XFER_UDMA_4 */ 0x1c8a9c62, | |
353 | /* XFER_UDMA_3 */ 0x1c8e9c62, | |
354 | /* XFER_UDMA_2 */ 0x1c929c62, | |
355 | /* XFER_UDMA_1 */ 0x1c9a9c62, | |
356 | /* XFER_UDMA_0 */ 0x1c829c62, | |
357 | ||
358 | /* XFER_MW_DMA_2 */ 0x2c829c62, | |
359 | /* XFER_MW_DMA_1 */ 0x2c829c66, | |
360 | /* XFER_MW_DMA_0 */ 0x2c829d2e, | |
361 | ||
362 | /* XFER_PIO_4 */ 0x0c829c62, | |
363 | /* XFER_PIO_3 */ 0x0c829c84, | |
364 | /* XFER_PIO_2 */ 0x0c829ca6, | |
365 | /* XFER_PIO_1 */ 0x0d029d26, | |
366 | /* XFER_PIO_0 */ 0x0d029d5e | |
1da177e4 LT |
367 | }; |
368 | ||
1da177e4 | 369 | #define HPT366_DEBUG_DRIVE_INFO 0 |
7b73ee05 SS |
370 | #define HPT371_ALLOW_ATA133_6 1 |
371 | #define HPT302_ALLOW_ATA133_6 1 | |
372 | #define HPT372_ALLOW_ATA133_6 1 | |
e139b0b0 | 373 | #define HPT370_ALLOW_ATA100_5 0 |
1da177e4 LT |
374 | #define HPT366_ALLOW_ATA66_4 1 |
375 | #define HPT366_ALLOW_ATA66_3 1 | |
376 | #define HPT366_MAX_DEVS 8 | |
377 | ||
7b73ee05 SS |
378 | /* Supported ATA clock frequencies */ |
379 | enum ata_clock { | |
380 | ATA_CLOCK_25MHZ, | |
381 | ATA_CLOCK_33MHZ, | |
382 | ATA_CLOCK_40MHZ, | |
383 | ATA_CLOCK_50MHZ, | |
384 | ATA_CLOCK_66MHZ, | |
385 | NUM_ATA_CLOCKS | |
386 | }; | |
1da177e4 | 387 | |
b39b01ff | 388 | /* |
7b73ee05 | 389 | * Hold all the HighPoint chip information in one place. |
b39b01ff | 390 | */ |
1da177e4 | 391 | |
7b73ee05 SS |
392 | struct hpt_info { |
393 | u8 chip_type; /* Chip type */ | |
b39b01ff | 394 | u8 max_mode; /* Speeds allowed */ |
7b73ee05 SS |
395 | u8 dpll_clk; /* DPLL clock in MHz */ |
396 | u8 pci_clk; /* PCI clock in MHz */ | |
397 | u32 **settings; /* Chipset settings table */ | |
b39b01ff AC |
398 | }; |
399 | ||
7b73ee05 SS |
400 | /* Supported HighPoint chips */ |
401 | enum { | |
402 | HPT36x, | |
403 | HPT370, | |
404 | HPT370A, | |
405 | HPT374, | |
406 | HPT372, | |
407 | HPT372A, | |
408 | HPT302, | |
409 | HPT371, | |
410 | HPT372N, | |
411 | HPT302N, | |
412 | HPT371N | |
413 | }; | |
b39b01ff | 414 | |
7b73ee05 SS |
415 | static u32 *hpt36x_settings[NUM_ATA_CLOCKS] = { |
416 | twenty_five_base_hpt36x, | |
417 | thirty_three_base_hpt36x, | |
418 | forty_base_hpt36x, | |
419 | NULL, | |
420 | NULL | |
421 | }; | |
e139b0b0 | 422 | |
7b73ee05 SS |
423 | static u32 *hpt37x_settings[NUM_ATA_CLOCKS] = { |
424 | NULL, | |
425 | thirty_three_base_hpt37x, | |
426 | NULL, | |
427 | fifty_base_hpt37x, | |
428 | sixty_six_base_hpt37x | |
429 | }; | |
1da177e4 | 430 | |
7b73ee05 SS |
431 | static struct hpt_info hpt36x __devinitdata = { |
432 | .chip_type = HPT36x, | |
433 | .max_mode = (HPT366_ALLOW_ATA66_4 || HPT366_ALLOW_ATA66_3) ? 2 : 1, | |
434 | .dpll_clk = 0, /* no DPLL */ | |
435 | .settings = hpt36x_settings | |
436 | }; | |
437 | ||
438 | static struct hpt_info hpt370 __devinitdata = { | |
439 | .chip_type = HPT370, | |
440 | .max_mode = HPT370_ALLOW_ATA100_5 ? 3 : 2, | |
441 | .dpll_clk = 48, | |
442 | .settings = hpt37x_settings | |
443 | }; | |
444 | ||
445 | static struct hpt_info hpt370a __devinitdata = { | |
446 | .chip_type = HPT370A, | |
447 | .max_mode = HPT370_ALLOW_ATA100_5 ? 3 : 2, | |
448 | .dpll_clk = 48, | |
449 | .settings = hpt37x_settings | |
450 | }; | |
451 | ||
452 | static struct hpt_info hpt374 __devinitdata = { | |
453 | .chip_type = HPT374, | |
278978e9 | 454 | .max_mode = 3, |
7b73ee05 SS |
455 | .dpll_clk = 48, |
456 | .settings = hpt37x_settings | |
457 | }; | |
458 | ||
459 | static struct hpt_info hpt372 __devinitdata = { | |
460 | .chip_type = HPT372, | |
461 | .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3, | |
462 | .dpll_clk = 55, | |
463 | .settings = hpt37x_settings | |
464 | }; | |
465 | ||
466 | static struct hpt_info hpt372a __devinitdata = { | |
467 | .chip_type = HPT372A, | |
468 | .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3, | |
469 | .dpll_clk = 66, | |
470 | .settings = hpt37x_settings | |
471 | }; | |
472 | ||
473 | static struct hpt_info hpt302 __devinitdata = { | |
474 | .chip_type = HPT302, | |
475 | .max_mode = HPT302_ALLOW_ATA133_6 ? 4 : 3, | |
476 | .dpll_clk = 66, | |
477 | .settings = hpt37x_settings | |
478 | }; | |
479 | ||
480 | static struct hpt_info hpt371 __devinitdata = { | |
481 | .chip_type = HPT371, | |
482 | .max_mode = HPT371_ALLOW_ATA133_6 ? 4 : 3, | |
483 | .dpll_clk = 66, | |
484 | .settings = hpt37x_settings | |
485 | }; | |
486 | ||
487 | static struct hpt_info hpt372n __devinitdata = { | |
488 | .chip_type = HPT372N, | |
489 | .max_mode = HPT372_ALLOW_ATA133_6 ? 4 : 3, | |
490 | .dpll_clk = 77, | |
491 | .settings = hpt37x_settings | |
492 | }; | |
493 | ||
494 | static struct hpt_info hpt302n __devinitdata = { | |
495 | .chip_type = HPT302N, | |
496 | .max_mode = HPT302_ALLOW_ATA133_6 ? 4 : 3, | |
497 | .dpll_clk = 77, | |
38b66f84 | 498 | .settings = hpt37x_settings |
7b73ee05 SS |
499 | }; |
500 | ||
501 | static struct hpt_info hpt371n __devinitdata = { | |
502 | .chip_type = HPT371N, | |
503 | .max_mode = HPT371_ALLOW_ATA133_6 ? 4 : 3, | |
504 | .dpll_clk = 77, | |
505 | .settings = hpt37x_settings | |
506 | }; | |
1da177e4 | 507 | |
e139b0b0 SS |
508 | static int check_in_drive_list(ide_drive_t *drive, const char **list) |
509 | { | |
510 | struct hd_driveid *id = drive->id; | |
511 | ||
512 | while (*list) | |
513 | if (!strcmp(*list++,id->model)) | |
514 | return 1; | |
515 | return 0; | |
516 | } | |
1da177e4 | 517 | |
1da177e4 LT |
518 | /* |
519 | * Note for the future; the SATA hpt37x we must set | |
520 | * either PIO or UDMA modes 0,4,5 | |
521 | */ | |
2d5eaa6d BZ |
522 | |
523 | static u8 hpt3xx_udma_filter(ide_drive_t *drive) | |
1da177e4 | 524 | { |
7b73ee05 SS |
525 | struct hpt_info *info = pci_get_drvdata(HWIF(drive)->pci_dev); |
526 | u8 chip_type = info->chip_type; | |
2d5eaa6d BZ |
527 | u8 mode = info->max_mode; |
528 | u8 mask; | |
1da177e4 | 529 | |
e139b0b0 | 530 | switch (mode) { |
1da177e4 | 531 | case 0x04: |
2d5eaa6d | 532 | mask = 0x7f; |
1da177e4 LT |
533 | break; |
534 | case 0x03: | |
2d5eaa6d | 535 | mask = 0x3f; |
7b73ee05 | 536 | if (chip_type >= HPT374) |
1da177e4 | 537 | break; |
e139b0b0 SS |
538 | if (!check_in_drive_list(drive, bad_ata100_5)) |
539 | goto check_bad_ata33; | |
540 | /* fall thru */ | |
1da177e4 | 541 | case 0x02: |
2d5eaa6d | 542 | mask = 0x1f; |
7b73ee05 SS |
543 | |
544 | /* | |
545 | * CHECK ME, Does this need to be changed to HPT374 ?? | |
546 | */ | |
547 | if (chip_type >= HPT370) | |
e139b0b0 SS |
548 | goto check_bad_ata33; |
549 | if (HPT366_ALLOW_ATA66_4 && | |
550 | !check_in_drive_list(drive, bad_ata66_4)) | |
551 | goto check_bad_ata33; | |
552 | ||
2d5eaa6d | 553 | mask = 0x0f; |
e139b0b0 SS |
554 | if (HPT366_ALLOW_ATA66_3 && |
555 | !check_in_drive_list(drive, bad_ata66_3)) | |
556 | goto check_bad_ata33; | |
557 | /* fall thru */ | |
1da177e4 | 558 | case 0x01: |
2d5eaa6d | 559 | mask = 0x07; |
e139b0b0 SS |
560 | |
561 | check_bad_ata33: | |
7b73ee05 | 562 | if (chip_type >= HPT370A) |
1da177e4 | 563 | break; |
e139b0b0 SS |
564 | if (!check_in_drive_list(drive, bad_ata33)) |
565 | break; | |
566 | /* fall thru */ | |
1da177e4 LT |
567 | case 0x00: |
568 | default: | |
2d5eaa6d | 569 | mask = 0x00; |
1da177e4 LT |
570 | break; |
571 | } | |
2d5eaa6d | 572 | return mask; |
1da177e4 LT |
573 | } |
574 | ||
7b73ee05 | 575 | static u32 get_speed_setting(u8 speed, struct hpt_info *info) |
1da177e4 | 576 | { |
471a0bda SS |
577 | int i; |
578 | ||
579 | /* | |
580 | * Lookup the transfer mode table to get the index into | |
581 | * the timing table. | |
582 | * | |
583 | * NOTE: For XFER_PIO_SLOW, PIO mode 0 timings will be used. | |
584 | */ | |
585 | for (i = 0; i < ARRAY_SIZE(xfer_speeds) - 1; i++) | |
586 | if (xfer_speeds[i] == speed) | |
587 | break; | |
7b73ee05 SS |
588 | /* |
589 | * NOTE: info->settings only points to the pointer | |
590 | * to the list of the actual register values | |
591 | */ | |
592 | return (*info->settings)[i]; | |
1da177e4 LT |
593 | } |
594 | ||
595 | static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed) | |
596 | { | |
abc4ad4c SS |
597 | ide_hwif_t *hwif = HWIF(drive); |
598 | struct pci_dev *dev = hwif->pci_dev; | |
7b73ee05 | 599 | struct hpt_info *info = pci_get_drvdata(dev); |
2d5eaa6d | 600 | u8 speed = ide_rate_filter(drive, xferspeed); |
abc4ad4c | 601 | u8 itr_addr = drive->dn ? 0x44 : 0x40; |
26ccb802 | 602 | u32 old_itr = 0; |
2d5eaa6d BZ |
603 | u32 itr_mask, new_itr; |
604 | ||
605 | /* TODO: move this to ide_rate_filter() [ check ->atapi_dma ] */ | |
606 | if (drive->media != ide_disk) | |
607 | speed = min_t(u8, speed, XFER_PIO_4); | |
608 | ||
609 | itr_mask = speed < XFER_MW_DMA_0 ? 0x30070000 : | |
610 | (speed < XFER_UDMA_0 ? 0xc0070000 : 0xc03800ff); | |
611 | ||
612 | new_itr = get_speed_setting(speed, info); | |
b39b01ff | 613 | |
1da177e4 | 614 | /* |
abc4ad4c SS |
615 | * Disable on-chip PIO FIFO/buffer (and PIO MST mode as well) |
616 | * to avoid problems handling I/O errors later | |
1da177e4 | 617 | */ |
abc4ad4c SS |
618 | pci_read_config_dword(dev, itr_addr, &old_itr); |
619 | new_itr = (new_itr & ~itr_mask) | (old_itr & itr_mask); | |
620 | new_itr &= ~0xc0000000; | |
1da177e4 | 621 | |
abc4ad4c | 622 | pci_write_config_dword(dev, itr_addr, new_itr); |
1da177e4 LT |
623 | |
624 | return ide_config_drive_speed(drive, speed); | |
625 | } | |
626 | ||
26ccb802 | 627 | static int hpt37x_tune_chipset(ide_drive_t *drive, u8 xferspeed) |
1da177e4 | 628 | { |
abc4ad4c SS |
629 | ide_hwif_t *hwif = HWIF(drive); |
630 | struct pci_dev *dev = hwif->pci_dev; | |
7b73ee05 | 631 | struct hpt_info *info = pci_get_drvdata(dev); |
2d5eaa6d | 632 | u8 speed = ide_rate_filter(drive, xferspeed); |
abc4ad4c | 633 | u8 itr_addr = 0x40 + (drive->dn * 4); |
26ccb802 | 634 | u32 old_itr = 0; |
2d5eaa6d BZ |
635 | u32 itr_mask, new_itr; |
636 | ||
637 | /* TODO: move this to ide_rate_filter() [ check ->atapi_dma ] */ | |
638 | if (drive->media != ide_disk) | |
639 | speed = min_t(u8, speed, XFER_PIO_4); | |
640 | ||
641 | itr_mask = speed < XFER_MW_DMA_0 ? 0x303c0000 : | |
642 | (speed < XFER_UDMA_0 ? 0xc03c0000 : 0xc1c001ff); | |
643 | ||
644 | new_itr = get_speed_setting(speed, info); | |
1da177e4 | 645 | |
abc4ad4c SS |
646 | pci_read_config_dword(dev, itr_addr, &old_itr); |
647 | new_itr = (new_itr & ~itr_mask) | (old_itr & itr_mask); | |
1da177e4 | 648 | |
b39b01ff | 649 | if (speed < XFER_MW_DMA_0) |
abc4ad4c SS |
650 | new_itr &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */ |
651 | pci_write_config_dword(dev, itr_addr, new_itr); | |
1da177e4 LT |
652 | |
653 | return ide_config_drive_speed(drive, speed); | |
654 | } | |
655 | ||
26ccb802 | 656 | static int hpt3xx_tune_chipset(ide_drive_t *drive, u8 speed) |
1da177e4 | 657 | { |
abc4ad4c | 658 | ide_hwif_t *hwif = HWIF(drive); |
7b73ee05 | 659 | struct hpt_info *info = pci_get_drvdata(hwif->pci_dev); |
1da177e4 | 660 | |
7b73ee05 | 661 | if (info->chip_type >= HPT370) |
26ccb802 | 662 | return hpt37x_tune_chipset(drive, speed); |
1da177e4 LT |
663 | else /* hpt368: hpt_minimum_revision(dev, 2) */ |
664 | return hpt36x_tune_chipset(drive, speed); | |
665 | } | |
666 | ||
26ccb802 | 667 | static void hpt3xx_tune_drive(ide_drive_t *drive, u8 pio) |
1da177e4 | 668 | { |
26ccb802 SS |
669 | pio = ide_get_best_pio_mode(drive, pio, 4, NULL); |
670 | (void) hpt3xx_tune_chipset (drive, XFER_PIO_0 + pio); | |
1da177e4 LT |
671 | } |
672 | ||
e139b0b0 | 673 | static int hpt3xx_quirkproc(ide_drive_t *drive) |
1da177e4 | 674 | { |
e139b0b0 SS |
675 | struct hd_driveid *id = drive->id; |
676 | const char **list = quirk_drives; | |
677 | ||
678 | while (*list) | |
679 | if (strstr(id->model, *list++)) | |
680 | return 1; | |
681 | return 0; | |
1da177e4 LT |
682 | } |
683 | ||
26ccb802 | 684 | static void hpt3xx_intrproc(ide_drive_t *drive) |
1da177e4 | 685 | { |
abc4ad4c | 686 | ide_hwif_t *hwif = HWIF(drive); |
1da177e4 LT |
687 | |
688 | if (drive->quirk_list) | |
689 | return; | |
690 | /* drives in the quirk_list may not like intr setups/cleanups */ | |
abc4ad4c | 691 | hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG); |
1da177e4 LT |
692 | } |
693 | ||
26ccb802 | 694 | static void hpt3xx_maskproc(ide_drive_t *drive, int mask) |
1da177e4 | 695 | { |
abc4ad4c SS |
696 | ide_hwif_t *hwif = HWIF(drive); |
697 | struct pci_dev *dev = hwif->pci_dev; | |
7b73ee05 | 698 | struct hpt_info *info = pci_get_drvdata(dev); |
1da177e4 LT |
699 | |
700 | if (drive->quirk_list) { | |
7b73ee05 | 701 | if (info->chip_type >= HPT370) { |
abc4ad4c SS |
702 | u8 scr1 = 0; |
703 | ||
704 | pci_read_config_byte(dev, 0x5a, &scr1); | |
705 | if (((scr1 & 0x10) >> 4) != mask) { | |
706 | if (mask) | |
707 | scr1 |= 0x10; | |
708 | else | |
709 | scr1 &= ~0x10; | |
710 | pci_write_config_byte(dev, 0x5a, scr1); | |
711 | } | |
1da177e4 | 712 | } else { |
abc4ad4c | 713 | if (mask) |
b39b01ff | 714 | disable_irq(hwif->irq); |
abc4ad4c SS |
715 | else |
716 | enable_irq (hwif->irq); | |
1da177e4 | 717 | } |
abc4ad4c SS |
718 | } else |
719 | hwif->OUTB(mask ? (drive->ctl | 2) : (drive->ctl & ~2), | |
720 | IDE_CONTROL_REG); | |
1da177e4 LT |
721 | } |
722 | ||
26ccb802 | 723 | static int hpt366_config_drive_xfer_rate(ide_drive_t *drive) |
1da177e4 | 724 | { |
1da177e4 LT |
725 | drive->init_speed = 0; |
726 | ||
29e744d0 | 727 | if (ide_tune_dma(drive)) |
3608b5d7 | 728 | return 0; |
1da177e4 | 729 | |
d8f4469d | 730 | if (ide_use_fast_pio(drive)) |
26ccb802 | 731 | hpt3xx_tune_drive(drive, 255); |
d8f4469d | 732 | |
3608b5d7 | 733 | return -1; |
1da177e4 LT |
734 | } |
735 | ||
736 | /* | |
abc4ad4c | 737 | * This is specific to the HPT366 UDMA chipset |
1da177e4 LT |
738 | * by HighPoint|Triones Technologies, Inc. |
739 | */ | |
abc4ad4c | 740 | static int hpt366_ide_dma_lostirq(ide_drive_t *drive) |
1da177e4 | 741 | { |
abc4ad4c SS |
742 | struct pci_dev *dev = HWIF(drive)->pci_dev; |
743 | u8 mcr1 = 0, mcr3 = 0, scr1 = 0; | |
744 | ||
745 | pci_read_config_byte(dev, 0x50, &mcr1); | |
746 | pci_read_config_byte(dev, 0x52, &mcr3); | |
747 | pci_read_config_byte(dev, 0x5a, &scr1); | |
748 | printk("%s: (%s) mcr1=0x%02x, mcr3=0x%02x, scr1=0x%02x\n", | |
749 | drive->name, __FUNCTION__, mcr1, mcr3, scr1); | |
750 | if (scr1 & 0x10) | |
751 | pci_write_config_byte(dev, 0x5a, scr1 & ~0x10); | |
1da177e4 LT |
752 | return __ide_dma_lostirq(drive); |
753 | } | |
754 | ||
4bf63de2 | 755 | static void hpt370_clear_engine(ide_drive_t *drive) |
1da177e4 | 756 | { |
abc4ad4c SS |
757 | ide_hwif_t *hwif = HWIF(drive); |
758 | ||
759 | pci_write_config_byte(hwif->pci_dev, hwif->select_data, 0x37); | |
1da177e4 LT |
760 | udelay(10); |
761 | } | |
762 | ||
4bf63de2 SS |
763 | static void hpt370_irq_timeout(ide_drive_t *drive) |
764 | { | |
765 | ide_hwif_t *hwif = HWIF(drive); | |
766 | u16 bfifo = 0; | |
767 | u8 dma_cmd; | |
768 | ||
769 | pci_read_config_word(hwif->pci_dev, hwif->select_data + 2, &bfifo); | |
770 | printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo & 0x1ff); | |
771 | ||
772 | /* get DMA command mode */ | |
773 | dma_cmd = hwif->INB(hwif->dma_command); | |
774 | /* stop DMA */ | |
775 | hwif->OUTB(dma_cmd & ~0x1, hwif->dma_command); | |
776 | hpt370_clear_engine(drive); | |
777 | } | |
778 | ||
1da177e4 LT |
779 | static void hpt370_ide_dma_start(ide_drive_t *drive) |
780 | { | |
781 | #ifdef HPT_RESET_STATE_ENGINE | |
782 | hpt370_clear_engine(drive); | |
783 | #endif | |
784 | ide_dma_start(drive); | |
785 | } | |
786 | ||
4bf63de2 | 787 | static int hpt370_ide_dma_end(ide_drive_t *drive) |
1da177e4 LT |
788 | { |
789 | ide_hwif_t *hwif = HWIF(drive); | |
4bf63de2 | 790 | u8 dma_stat = hwif->INB(hwif->dma_status); |
1da177e4 LT |
791 | |
792 | if (dma_stat & 0x01) { | |
793 | /* wait a little */ | |
794 | udelay(20); | |
795 | dma_stat = hwif->INB(hwif->dma_status); | |
4bf63de2 SS |
796 | if (dma_stat & 0x01) |
797 | hpt370_irq_timeout(drive); | |
1da177e4 | 798 | } |
1da177e4 LT |
799 | return __ide_dma_end(drive); |
800 | } | |
801 | ||
4bf63de2 | 802 | static int hpt370_ide_dma_timeout(ide_drive_t *drive) |
1da177e4 | 803 | { |
4bf63de2 | 804 | hpt370_irq_timeout(drive); |
1da177e4 LT |
805 | return __ide_dma_timeout(drive); |
806 | } | |
807 | ||
1da177e4 LT |
808 | /* returns 1 if DMA IRQ issued, 0 otherwise */ |
809 | static int hpt374_ide_dma_test_irq(ide_drive_t *drive) | |
810 | { | |
811 | ide_hwif_t *hwif = HWIF(drive); | |
812 | u16 bfifo = 0; | |
abc4ad4c | 813 | u8 dma_stat; |
1da177e4 | 814 | |
abc4ad4c | 815 | pci_read_config_word(hwif->pci_dev, hwif->select_data + 2, &bfifo); |
1da177e4 LT |
816 | if (bfifo & 0x1FF) { |
817 | // printk("%s: %d bytes in FIFO\n", drive->name, bfifo); | |
818 | return 0; | |
819 | } | |
820 | ||
0ecdca26 | 821 | dma_stat = inb(hwif->dma_status); |
1da177e4 | 822 | /* return 1 if INTR asserted */ |
abc4ad4c | 823 | if (dma_stat & 4) |
1da177e4 LT |
824 | return 1; |
825 | ||
826 | if (!drive->waiting_for_dma) | |
827 | printk(KERN_WARNING "%s: (%s) called while not waiting\n", | |
828 | drive->name, __FUNCTION__); | |
829 | return 0; | |
830 | } | |
831 | ||
abc4ad4c | 832 | static int hpt374_ide_dma_end(ide_drive_t *drive) |
1da177e4 | 833 | { |
1da177e4 | 834 | ide_hwif_t *hwif = HWIF(drive); |
abc4ad4c SS |
835 | struct pci_dev *dev = hwif->pci_dev; |
836 | u8 mcr = 0, mcr_addr = hwif->select_data; | |
837 | u8 bwsr = 0, mask = hwif->channel ? 0x02 : 0x01; | |
838 | ||
839 | pci_read_config_byte(dev, 0x6a, &bwsr); | |
840 | pci_read_config_byte(dev, mcr_addr, &mcr); | |
841 | if (bwsr & mask) | |
842 | pci_write_config_byte(dev, mcr_addr, mcr | 0x30); | |
1da177e4 LT |
843 | return __ide_dma_end(drive); |
844 | } | |
845 | ||
846 | /** | |
836c0063 SS |
847 | * hpt3xxn_set_clock - perform clock switching dance |
848 | * @hwif: hwif to switch | |
849 | * @mode: clocking mode (0x21 for write, 0x23 otherwise) | |
1da177e4 | 850 | * |
836c0063 | 851 | * Switch the DPLL clock on the HPT3xxN devices. This is a right mess. |
1da177e4 | 852 | */ |
836c0063 SS |
853 | |
854 | static void hpt3xxn_set_clock(ide_hwif_t *hwif, u8 mode) | |
1da177e4 | 855 | { |
7b73ee05 | 856 | u8 scr2 = hwif->INB(hwif->dma_master + 0x7b); |
836c0063 SS |
857 | |
858 | if ((scr2 & 0x7f) == mode) | |
859 | return; | |
860 | ||
1da177e4 | 861 | /* Tristate the bus */ |
7b73ee05 | 862 | hwif->OUTB(0x80, hwif->dma_master + 0x73); |
836c0063 SS |
863 | hwif->OUTB(0x80, hwif->dma_master + 0x77); |
864 | ||
1da177e4 | 865 | /* Switch clock and reset channels */ |
836c0063 SS |
866 | hwif->OUTB(mode, hwif->dma_master + 0x7b); |
867 | hwif->OUTB(0xc0, hwif->dma_master + 0x79); | |
868 | ||
7b73ee05 SS |
869 | /* |
870 | * Reset the state machines. | |
871 | * NOTE: avoid accidentally enabling the disabled channels. | |
872 | */ | |
873 | hwif->OUTB(hwif->INB(hwif->dma_master + 0x70) | 0x32, | |
874 | hwif->dma_master + 0x70); | |
875 | hwif->OUTB(hwif->INB(hwif->dma_master + 0x74) | 0x32, | |
876 | hwif->dma_master + 0x74); | |
836c0063 | 877 | |
1da177e4 | 878 | /* Complete reset */ |
836c0063 SS |
879 | hwif->OUTB(0x00, hwif->dma_master + 0x79); |
880 | ||
1da177e4 | 881 | /* Reconnect channels to bus */ |
7b73ee05 | 882 | hwif->OUTB(0x00, hwif->dma_master + 0x73); |
836c0063 | 883 | hwif->OUTB(0x00, hwif->dma_master + 0x77); |
1da177e4 LT |
884 | } |
885 | ||
886 | /** | |
836c0063 | 887 | * hpt3xxn_rw_disk - prepare for I/O |
1da177e4 LT |
888 | * @drive: drive for command |
889 | * @rq: block request structure | |
890 | * | |
836c0063 | 891 | * This is called when a disk I/O is issued to HPT3xxN. |
1da177e4 LT |
892 | * We need it because of the clock switching. |
893 | */ | |
894 | ||
836c0063 | 895 | static void hpt3xxn_rw_disk(ide_drive_t *drive, struct request *rq) |
1da177e4 | 896 | { |
7b73ee05 | 897 | hpt3xxn_set_clock(HWIF(drive), rq_data_dir(rq) ? 0x23 : 0x21); |
1da177e4 LT |
898 | } |
899 | ||
1da177e4 | 900 | /* |
33b18a60 | 901 | * Set/get power state for a drive. |
abc4ad4c | 902 | * NOTE: affects both drives on each channel. |
1da177e4 | 903 | * |
33b18a60 | 904 | * When we turn the power back on, we need to re-initialize things. |
1da177e4 LT |
905 | */ |
906 | #define TRISTATE_BIT 0x8000 | |
33b18a60 SS |
907 | |
908 | static int hpt3xx_busproc(ide_drive_t *drive, int state) | |
1da177e4 | 909 | { |
abc4ad4c | 910 | ide_hwif_t *hwif = HWIF(drive); |
1da177e4 | 911 | struct pci_dev *dev = hwif->pci_dev; |
abc4ad4c SS |
912 | u8 mcr_addr = hwif->select_data + 2; |
913 | u8 resetmask = hwif->channel ? 0x80 : 0x40; | |
914 | u8 bsr2 = 0; | |
915 | u16 mcr = 0; | |
1da177e4 LT |
916 | |
917 | hwif->bus_state = state; | |
918 | ||
33b18a60 | 919 | /* Grab the status. */ |
abc4ad4c SS |
920 | pci_read_config_word(dev, mcr_addr, &mcr); |
921 | pci_read_config_byte(dev, 0x59, &bsr2); | |
1da177e4 | 922 | |
33b18a60 SS |
923 | /* |
924 | * Set the state. We don't set it if we don't need to do so. | |
925 | * Make sure that the drive knows that it has failed if it's off. | |
926 | */ | |
1da177e4 LT |
927 | switch (state) { |
928 | case BUSSTATE_ON: | |
abc4ad4c | 929 | if (!(bsr2 & resetmask)) |
1da177e4 | 930 | return 0; |
33b18a60 SS |
931 | hwif->drives[0].failures = hwif->drives[1].failures = 0; |
932 | ||
abc4ad4c SS |
933 | pci_write_config_byte(dev, 0x59, bsr2 & ~resetmask); |
934 | pci_write_config_word(dev, mcr_addr, mcr & ~TRISTATE_BIT); | |
33b18a60 | 935 | return 0; |
1da177e4 | 936 | case BUSSTATE_OFF: |
abc4ad4c | 937 | if ((bsr2 & resetmask) && !(mcr & TRISTATE_BIT)) |
1da177e4 | 938 | return 0; |
abc4ad4c | 939 | mcr &= ~TRISTATE_BIT; |
1da177e4 LT |
940 | break; |
941 | case BUSSTATE_TRISTATE: | |
abc4ad4c | 942 | if ((bsr2 & resetmask) && (mcr & TRISTATE_BIT)) |
1da177e4 | 943 | return 0; |
abc4ad4c | 944 | mcr |= TRISTATE_BIT; |
1da177e4 | 945 | break; |
33b18a60 SS |
946 | default: |
947 | return -EINVAL; | |
1da177e4 | 948 | } |
1da177e4 | 949 | |
33b18a60 SS |
950 | hwif->drives[0].failures = hwif->drives[0].max_failures + 1; |
951 | hwif->drives[1].failures = hwif->drives[1].max_failures + 1; | |
952 | ||
abc4ad4c SS |
953 | pci_write_config_word(dev, mcr_addr, mcr); |
954 | pci_write_config_byte(dev, 0x59, bsr2 | resetmask); | |
1da177e4 LT |
955 | return 0; |
956 | } | |
957 | ||
7b73ee05 SS |
958 | /** |
959 | * hpt37x_calibrate_dpll - calibrate the DPLL | |
960 | * @dev: PCI device | |
961 | * | |
962 | * Perform a calibration cycle on the DPLL. | |
963 | * Returns 1 if this succeeds | |
964 | */ | |
965 | static int __devinit hpt37x_calibrate_dpll(struct pci_dev *dev, u16 f_low, u16 f_high) | |
1da177e4 | 966 | { |
7b73ee05 SS |
967 | u32 dpll = (f_high << 16) | f_low | 0x100; |
968 | u8 scr2; | |
969 | int i; | |
b39b01ff | 970 | |
7b73ee05 | 971 | pci_write_config_dword(dev, 0x5c, dpll); |
b39b01ff | 972 | |
7b73ee05 SS |
973 | /* Wait for oscillator ready */ |
974 | for(i = 0; i < 0x5000; ++i) { | |
975 | udelay(50); | |
976 | pci_read_config_byte(dev, 0x5b, &scr2); | |
977 | if (scr2 & 0x80) | |
b39b01ff AC |
978 | break; |
979 | } | |
7b73ee05 SS |
980 | /* See if it stays ready (we'll just bail out if it's not yet) */ |
981 | for(i = 0; i < 0x1000; ++i) { | |
982 | pci_read_config_byte(dev, 0x5b, &scr2); | |
983 | /* DPLL destabilized? */ | |
984 | if(!(scr2 & 0x80)) | |
985 | return 0; | |
986 | } | |
987 | /* Turn off tuning, we have the DPLL set */ | |
988 | pci_read_config_dword (dev, 0x5c, &dpll); | |
989 | pci_write_config_dword(dev, 0x5c, (dpll & ~0x100)); | |
990 | return 1; | |
b39b01ff AC |
991 | } |
992 | ||
7b73ee05 | 993 | static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name) |
b39b01ff | 994 | { |
7b73ee05 SS |
995 | struct hpt_info *info = kmalloc(sizeof(struct hpt_info), GFP_KERNEL); |
996 | unsigned long io_base = pci_resource_start(dev, 4); | |
997 | u8 pci_clk, dpll_clk = 0; /* PCI and DPLL clock in MHz */ | |
998 | enum ata_clock clock; | |
999 | ||
1000 | if (info == NULL) { | |
1001 | printk(KERN_ERR "%s: out of memory!\n", name); | |
1002 | return -ENOMEM; | |
1003 | } | |
1004 | ||
1da177e4 | 1005 | /* |
7b73ee05 SS |
1006 | * Copy everything from a static "template" structure |
1007 | * to just allocated per-chip hpt_info structure. | |
1da177e4 | 1008 | */ |
7b73ee05 | 1009 | *info = *(struct hpt_info *)pci_get_drvdata(dev); |
1da177e4 LT |
1010 | |
1011 | /* | |
7b73ee05 SS |
1012 | * FIXME: Not portable. Also, why do we enable the ROM in the first place? |
1013 | * We don't seem to be using it. | |
1da177e4 | 1014 | */ |
7b73ee05 SS |
1015 | if (dev->resource[PCI_ROM_RESOURCE].start) |
1016 | pci_write_config_dword(dev, PCI_ROM_ADDRESS, | |
1017 | dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE); | |
1018 | ||
1019 | pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); | |
1020 | pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); | |
1021 | pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); | |
1022 | pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); | |
26c068da | 1023 | |
1da177e4 | 1024 | /* |
7b73ee05 | 1025 | * First, try to estimate the PCI clock frequency... |
1da177e4 | 1026 | */ |
7b73ee05 SS |
1027 | if (info->chip_type >= HPT370) { |
1028 | u8 scr1 = 0; | |
1029 | u16 f_cnt = 0; | |
1030 | u32 temp = 0; | |
1031 | ||
1032 | /* Interrupt force enable. */ | |
1033 | pci_read_config_byte(dev, 0x5a, &scr1); | |
1034 | if (scr1 & 0x10) | |
1035 | pci_write_config_byte(dev, 0x5a, scr1 & ~0x10); | |
1036 | ||
1037 | /* | |
1038 | * HighPoint does this for HPT372A. | |
1039 | * NOTE: This register is only writeable via I/O space. | |
1040 | */ | |
1041 | if (info->chip_type == HPT372A) | |
1042 | outb(0x0e, io_base + 0x9c); | |
1043 | ||
1044 | /* | |
1045 | * Default to PCI clock. Make sure MA15/16 are set to output | |
1046 | * to prevent drives having problems with 40-pin cables. | |
1047 | */ | |
1048 | pci_write_config_byte(dev, 0x5b, 0x23); | |
836c0063 | 1049 | |
7b73ee05 SS |
1050 | /* |
1051 | * We'll have to read f_CNT value in order to determine | |
1052 | * the PCI clock frequency according to the following ratio: | |
1053 | * | |
1054 | * f_CNT = Fpci * 192 / Fdpll | |
1055 | * | |
1056 | * First try reading the register in which the HighPoint BIOS | |
1057 | * saves f_CNT value before reprogramming the DPLL from its | |
1058 | * default setting (which differs for the various chips). | |
1059 | * NOTE: This register is only accessible via I/O space. | |
1060 | * | |
1061 | * In case the signature check fails, we'll have to resort to | |
1062 | * reading the f_CNT register itself in hopes that nobody has | |
1063 | * touched the DPLL yet... | |
1064 | */ | |
1065 | temp = inl(io_base + 0x90); | |
1066 | if ((temp & 0xFFFFF000) != 0xABCDE000) { | |
1067 | int i; | |
1068 | ||
1069 | printk(KERN_WARNING "%s: no clock data saved by BIOS\n", | |
1070 | name); | |
1071 | ||
1072 | /* Calculate the average value of f_CNT. */ | |
1073 | for (temp = i = 0; i < 128; i++) { | |
1074 | pci_read_config_word(dev, 0x78, &f_cnt); | |
1075 | temp += f_cnt & 0x1ff; | |
1076 | mdelay(1); | |
1077 | } | |
1078 | f_cnt = temp / 128; | |
1079 | } else | |
1080 | f_cnt = temp & 0x1ff; | |
1081 | ||
1082 | dpll_clk = info->dpll_clk; | |
1083 | pci_clk = (f_cnt * dpll_clk) / 192; | |
1084 | ||
1085 | /* Clamp PCI clock to bands. */ | |
1086 | if (pci_clk < 40) | |
1087 | pci_clk = 33; | |
1088 | else if(pci_clk < 45) | |
1089 | pci_clk = 40; | |
1090 | else if(pci_clk < 55) | |
1091 | pci_clk = 50; | |
1da177e4 | 1092 | else |
7b73ee05 | 1093 | pci_clk = 66; |
836c0063 | 1094 | |
7b73ee05 SS |
1095 | printk(KERN_INFO "%s: DPLL base: %d MHz, f_CNT: %d, " |
1096 | "assuming %d MHz PCI\n", name, dpll_clk, f_cnt, pci_clk); | |
90778574 | 1097 | } else { |
7b73ee05 SS |
1098 | u32 itr1 = 0; |
1099 | ||
1100 | pci_read_config_dword(dev, 0x40, &itr1); | |
1101 | ||
1102 | /* Detect PCI clock by looking at cmd_high_time. */ | |
1103 | switch((itr1 >> 8) & 0x07) { | |
1104 | case 0x09: | |
1105 | pci_clk = 40; | |
6273d26a | 1106 | break; |
7b73ee05 SS |
1107 | case 0x05: |
1108 | pci_clk = 25; | |
6273d26a | 1109 | break; |
7b73ee05 SS |
1110 | case 0x07: |
1111 | default: | |
1112 | pci_clk = 33; | |
6273d26a | 1113 | break; |
1da177e4 LT |
1114 | } |
1115 | } | |
836c0063 | 1116 | |
7b73ee05 SS |
1117 | /* Let's assume we'll use PCI clock for the ATA clock... */ |
1118 | switch (pci_clk) { | |
1119 | case 25: | |
1120 | clock = ATA_CLOCK_25MHZ; | |
1121 | break; | |
1122 | case 33: | |
1123 | default: | |
1124 | clock = ATA_CLOCK_33MHZ; | |
1125 | break; | |
1126 | case 40: | |
1127 | clock = ATA_CLOCK_40MHZ; | |
1128 | break; | |
1129 | case 50: | |
1130 | clock = ATA_CLOCK_50MHZ; | |
1131 | break; | |
1132 | case 66: | |
1133 | clock = ATA_CLOCK_66MHZ; | |
1134 | break; | |
1135 | } | |
836c0063 | 1136 | |
1da177e4 | 1137 | /* |
7b73ee05 SS |
1138 | * Only try the DPLL if we don't have a table for the PCI clock that |
1139 | * we are running at for HPT370/A, always use it for anything newer... | |
b39b01ff | 1140 | * |
7b73ee05 SS |
1141 | * NOTE: Using the internal DPLL results in slow reads on 33 MHz PCI. |
1142 | * We also don't like using the DPLL because this causes glitches | |
1143 | * on PRST-/SRST- when the state engine gets reset... | |
1da177e4 | 1144 | */ |
7b73ee05 SS |
1145 | if (info->chip_type >= HPT374 || info->settings[clock] == NULL) { |
1146 | u16 f_low, delta = pci_clk < 50 ? 2 : 4; | |
1147 | int adjust; | |
1148 | ||
1149 | /* | |
1150 | * Select 66 MHz DPLL clock only if UltraATA/133 mode is | |
1151 | * supported/enabled, use 50 MHz DPLL clock otherwise... | |
1152 | */ | |
1153 | if (info->max_mode == 0x04) { | |
1154 | dpll_clk = 66; | |
1155 | clock = ATA_CLOCK_66MHZ; | |
1156 | } else if (dpll_clk) { /* HPT36x chips don't have DPLL */ | |
1157 | dpll_clk = 50; | |
1158 | clock = ATA_CLOCK_50MHZ; | |
1159 | } | |
b39b01ff | 1160 | |
7b73ee05 SS |
1161 | if (info->settings[clock] == NULL) { |
1162 | printk(KERN_ERR "%s: unknown bus timing!\n", name); | |
1163 | kfree(info); | |
1164 | return -EIO; | |
1da177e4 | 1165 | } |
1da177e4 | 1166 | |
7b73ee05 SS |
1167 | /* Select the DPLL clock. */ |
1168 | pci_write_config_byte(dev, 0x5b, 0x21); | |
1169 | ||
1170 | /* | |
1171 | * Adjust the DPLL based upon PCI clock, enable it, | |
1172 | * and wait for stabilization... | |
1173 | */ | |
1174 | f_low = (pci_clk * 48) / dpll_clk; | |
1175 | ||
1176 | for (adjust = 0; adjust < 8; adjust++) { | |
1177 | if(hpt37x_calibrate_dpll(dev, f_low, f_low + delta)) | |
1178 | break; | |
1179 | ||
1180 | /* | |
1181 | * See if it'll settle at a fractionally different clock | |
1182 | */ | |
1183 | if (adjust & 1) | |
1184 | f_low -= adjust >> 1; | |
1185 | else | |
1186 | f_low += adjust >> 1; | |
1187 | } | |
1188 | if (adjust == 8) { | |
1189 | printk(KERN_ERR "%s: DPLL did not stabilize!\n", name); | |
1190 | kfree(info); | |
1191 | return -EIO; | |
1192 | } | |
1193 | ||
1194 | printk("%s: using %d MHz DPLL clock\n", name, dpll_clk); | |
1195 | } else { | |
1196 | /* Mark the fact that we're not using the DPLL. */ | |
1197 | dpll_clk = 0; | |
1198 | ||
1199 | printk("%s: using %d MHz PCI clock\n", name, pci_clk); | |
1200 | } | |
b39b01ff | 1201 | |
9ec4ff42 | 1202 | /* |
7b73ee05 SS |
1203 | * Advance the table pointer to a slot which points to the list |
1204 | * of the register values settings matching the clock being used. | |
9ec4ff42 | 1205 | */ |
7b73ee05 | 1206 | info->settings += clock; |
1da177e4 | 1207 | |
7b73ee05 SS |
1208 | /* Store the clock frequencies. */ |
1209 | info->dpll_clk = dpll_clk; | |
1210 | info->pci_clk = pci_clk; | |
1da177e4 | 1211 | |
7b73ee05 SS |
1212 | /* Point to this chip's own instance of the hpt_info structure. */ |
1213 | pci_set_drvdata(dev, info); | |
b39b01ff | 1214 | |
7b73ee05 SS |
1215 | if (info->chip_type >= HPT370) { |
1216 | u8 mcr1, mcr4; | |
1217 | ||
1218 | /* | |
1219 | * Reset the state engines. | |
1220 | * NOTE: Avoid accidentally enabling the disabled channels. | |
1221 | */ | |
1222 | pci_read_config_byte (dev, 0x50, &mcr1); | |
1223 | pci_read_config_byte (dev, 0x54, &mcr4); | |
1224 | pci_write_config_byte(dev, 0x50, (mcr1 | 0x32)); | |
1225 | pci_write_config_byte(dev, 0x54, (mcr4 | 0x32)); | |
1226 | udelay(100); | |
26ccb802 | 1227 | } |
1da177e4 | 1228 | |
7b73ee05 SS |
1229 | /* |
1230 | * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in | |
1231 | * the MISC. register to stretch the UltraDMA Tss timing. | |
1232 | * NOTE: This register is only writeable via I/O space. | |
1233 | */ | |
1234 | if (info->chip_type == HPT371N && clock == ATA_CLOCK_66MHZ) | |
1235 | ||
1236 | outb(inb(io_base + 0x9c) | 0x04, io_base + 0x9c); | |
1237 | ||
1da177e4 LT |
1238 | return dev->irq; |
1239 | } | |
1240 | ||
1241 | static void __devinit init_hwif_hpt366(ide_hwif_t *hwif) | |
1242 | { | |
26ccb802 | 1243 | struct pci_dev *dev = hwif->pci_dev; |
7b73ee05 | 1244 | struct hpt_info *info = pci_get_drvdata(dev); |
836c0063 | 1245 | int serialize = HPT_SERIALIZE_IO; |
abc4ad4c | 1246 | u8 scr1 = 0, ata66 = (hwif->channel) ? 0x01 : 0x02; |
7b73ee05 | 1247 | u8 chip_type = info->chip_type; |
26ccb802 | 1248 | u8 new_mcr, old_mcr = 0; |
abc4ad4c SS |
1249 | |
1250 | /* Cache the channel's MISC. control registers' offset */ | |
1251 | hwif->select_data = hwif->channel ? 0x54 : 0x50; | |
1252 | ||
1da177e4 LT |
1253 | hwif->tuneproc = &hpt3xx_tune_drive; |
1254 | hwif->speedproc = &hpt3xx_tune_chipset; | |
1255 | hwif->quirkproc = &hpt3xx_quirkproc; | |
1256 | hwif->intrproc = &hpt3xx_intrproc; | |
1257 | hwif->maskproc = &hpt3xx_maskproc; | |
abc4ad4c | 1258 | hwif->busproc = &hpt3xx_busproc; |
2d5eaa6d | 1259 | hwif->udma_filter = &hpt3xx_udma_filter; |
abc4ad4c | 1260 | |
836c0063 SS |
1261 | /* |
1262 | * HPT3xxN chips have some complications: | |
1263 | * | |
1264 | * - on 33 MHz PCI we must clock switch | |
1265 | * - on 66 MHz PCI we must NOT use the PCI clock | |
1266 | */ | |
7b73ee05 | 1267 | if (chip_type >= HPT372N && info->dpll_clk && info->pci_clk < 66) { |
836c0063 SS |
1268 | /* |
1269 | * Clock is shared between the channels, | |
1270 | * so we'll have to serialize them... :-( | |
1271 | */ | |
1272 | serialize = 1; | |
1273 | hwif->rw_disk = &hpt3xxn_rw_disk; | |
1274 | } | |
1da177e4 | 1275 | |
26ccb802 SS |
1276 | /* Serialize access to this device if needed */ |
1277 | if (serialize && hwif->mate) | |
1278 | hwif->serialized = hwif->mate->serialized = 1; | |
1279 | ||
1280 | /* | |
1281 | * Disable the "fast interrupt" prediction. Don't hold off | |
1282 | * on interrupts. (== 0x01 despite what the docs say) | |
1283 | */ | |
1284 | pci_read_config_byte(dev, hwif->select_data + 1, &old_mcr); | |
1285 | ||
7b73ee05 | 1286 | if (info->chip_type >= HPT374) |
26ccb802 | 1287 | new_mcr = old_mcr & ~0x07; |
7b73ee05 | 1288 | else if (info->chip_type >= HPT370) { |
26ccb802 SS |
1289 | new_mcr = old_mcr; |
1290 | new_mcr &= ~0x02; | |
1291 | ||
1292 | #ifdef HPT_DELAY_INTERRUPT | |
1293 | new_mcr &= ~0x01; | |
1294 | #else | |
1295 | new_mcr |= 0x01; | |
1296 | #endif | |
1297 | } else /* HPT366 and HPT368 */ | |
1298 | new_mcr = old_mcr & ~0x80; | |
1299 | ||
1300 | if (new_mcr != old_mcr) | |
1301 | pci_write_config_byte(dev, hwif->select_data + 1, new_mcr); | |
1302 | ||
1303 | if (!hwif->dma_base) { | |
1304 | hwif->drives[0].autotune = hwif->drives[1].autotune = 1; | |
1305 | return; | |
1306 | } | |
1307 | ||
1308 | hwif->ultra_mask = 0x7f; | |
1309 | hwif->mwdma_mask = 0x07; | |
1310 | ||
1da177e4 LT |
1311 | /* |
1312 | * The HPT37x uses the CBLID pins as outputs for MA15/MA16 | |
abc4ad4c | 1313 | * address lines to access an external EEPROM. To read valid |
1da177e4 LT |
1314 | * cable detect state the pins must be enabled as inputs. |
1315 | */ | |
7b73ee05 | 1316 | if (chip_type == HPT374 && (PCI_FUNC(dev->devfn) & 1)) { |
1da177e4 LT |
1317 | /* |
1318 | * HPT374 PCI function 1 | |
1319 | * - set bit 15 of reg 0x52 to enable TCBLID as input | |
1320 | * - set bit 15 of reg 0x56 to enable FCBLID as input | |
1321 | */ | |
abc4ad4c SS |
1322 | u8 mcr_addr = hwif->select_data + 2; |
1323 | u16 mcr; | |
1324 | ||
1325 | pci_read_config_word (dev, mcr_addr, &mcr); | |
1326 | pci_write_config_word(dev, mcr_addr, (mcr | 0x8000)); | |
1da177e4 | 1327 | /* now read cable id register */ |
abc4ad4c SS |
1328 | pci_read_config_byte (dev, 0x5a, &scr1); |
1329 | pci_write_config_word(dev, mcr_addr, mcr); | |
7b73ee05 | 1330 | } else if (chip_type >= HPT370) { |
1da177e4 LT |
1331 | /* |
1332 | * HPT370/372 and 374 pcifn 0 | |
abc4ad4c | 1333 | * - clear bit 0 of reg 0x5b to enable P/SCBLID as inputs |
1da177e4 | 1334 | */ |
abc4ad4c | 1335 | u8 scr2 = 0; |
1da177e4 | 1336 | |
abc4ad4c SS |
1337 | pci_read_config_byte (dev, 0x5b, &scr2); |
1338 | pci_write_config_byte(dev, 0x5b, (scr2 & ~1)); | |
1339 | /* now read cable id register */ | |
1340 | pci_read_config_byte (dev, 0x5a, &scr1); | |
1341 | pci_write_config_byte(dev, 0x5b, scr2); | |
1342 | } else | |
1343 | pci_read_config_byte (dev, 0x5a, &scr1); | |
1da177e4 | 1344 | |
26ccb802 SS |
1345 | if (!hwif->udma_four) |
1346 | hwif->udma_four = (scr1 & ata66) ? 0 : 1; | |
1da177e4 | 1347 | |
26ccb802 | 1348 | hwif->ide_dma_check = &hpt366_config_drive_xfer_rate; |
1da177e4 | 1349 | |
7b73ee05 | 1350 | if (chip_type >= HPT374) { |
26ccb802 SS |
1351 | hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq; |
1352 | hwif->ide_dma_end = &hpt374_ide_dma_end; | |
7b73ee05 | 1353 | } else if (chip_type >= HPT370) { |
26ccb802 SS |
1354 | hwif->dma_start = &hpt370_ide_dma_start; |
1355 | hwif->ide_dma_end = &hpt370_ide_dma_end; | |
1356 | hwif->ide_dma_timeout = &hpt370_ide_dma_timeout; | |
26ccb802 SS |
1357 | } else |
1358 | hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq; | |
1da177e4 LT |
1359 | |
1360 | if (!noautodma) | |
1361 | hwif->autodma = 1; | |
26ccb802 | 1362 | hwif->drives[0].autodma = hwif->drives[1].autodma = hwif->autodma; |
1da177e4 LT |
1363 | } |
1364 | ||
1365 | static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase) | |
1366 | { | |
26ccb802 | 1367 | struct pci_dev *dev = hwif->pci_dev; |
abc4ad4c SS |
1368 | u8 masterdma = 0, slavedma = 0; |
1369 | u8 dma_new = 0, dma_old = 0; | |
1da177e4 LT |
1370 | unsigned long flags; |
1371 | ||
26ccb802 | 1372 | dma_old = hwif->INB(dmabase + 2); |
1da177e4 LT |
1373 | |
1374 | local_irq_save(flags); | |
1375 | ||
1376 | dma_new = dma_old; | |
abc4ad4c SS |
1377 | pci_read_config_byte(dev, hwif->channel ? 0x4b : 0x43, &masterdma); |
1378 | pci_read_config_byte(dev, hwif->channel ? 0x4f : 0x47, &slavedma); | |
1da177e4 LT |
1379 | |
1380 | if (masterdma & 0x30) dma_new |= 0x20; | |
abc4ad4c | 1381 | if ( slavedma & 0x30) dma_new |= 0x40; |
1da177e4 | 1382 | if (dma_new != dma_old) |
abc4ad4c | 1383 | hwif->OUTB(dma_new, dmabase + 2); |
1da177e4 LT |
1384 | |
1385 | local_irq_restore(flags); | |
1386 | ||
1387 | ide_setup_dma(hwif, dmabase, 8); | |
1388 | } | |
1389 | ||
1390 | static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d) | |
1391 | { | |
b4586715 | 1392 | struct pci_dev *dev2; |
1da177e4 LT |
1393 | |
1394 | if (PCI_FUNC(dev->devfn) & 1) | |
1395 | return -ENODEV; | |
1396 | ||
7b73ee05 SS |
1397 | pci_set_drvdata(dev, &hpt374); |
1398 | ||
b4586715 SS |
1399 | if ((dev2 = pci_get_slot(dev->bus, dev->devfn + 1)) != NULL) { |
1400 | int ret; | |
1401 | ||
7b73ee05 SS |
1402 | pci_set_drvdata(dev2, &hpt374); |
1403 | ||
b4586715 SS |
1404 | if (dev2->irq != dev->irq) { |
1405 | /* FIXME: we need a core pci_set_interrupt() */ | |
1406 | dev2->irq = dev->irq; | |
1407 | printk(KERN_WARNING "%s: PCI config space interrupt " | |
1408 | "fixed.\n", d->name); | |
1da177e4 | 1409 | } |
b4586715 SS |
1410 | ret = ide_setup_pci_devices(dev, dev2, d); |
1411 | if (ret < 0) | |
1412 | pci_dev_put(dev2); | |
1413 | return ret; | |
1da177e4 LT |
1414 | } |
1415 | return ide_setup_pci_device(dev, d); | |
1416 | } | |
1417 | ||
90778574 | 1418 | static int __devinit init_setup_hpt372n(struct pci_dev *dev, ide_pci_device_t *d) |
1da177e4 | 1419 | { |
7b73ee05 SS |
1420 | pci_set_drvdata(dev, &hpt372n); |
1421 | ||
1da177e4 LT |
1422 | return ide_setup_pci_device(dev, d); |
1423 | } | |
1424 | ||
836c0063 SS |
1425 | static int __devinit init_setup_hpt371(struct pci_dev *dev, ide_pci_device_t *d) |
1426 | { | |
7b73ee05 | 1427 | struct hpt_info *info; |
90778574 SS |
1428 | u8 rev = 0, mcr1 = 0; |
1429 | ||
1430 | pci_read_config_byte(dev, PCI_REVISION_ID, &rev); | |
1431 | ||
7b73ee05 | 1432 | if (rev > 1) { |
90778574 | 1433 | d->name = "HPT371N"; |
836c0063 | 1434 | |
7b73ee05 SS |
1435 | info = &hpt371n; |
1436 | } else | |
1437 | info = &hpt371; | |
1438 | ||
836c0063 SS |
1439 | /* |
1440 | * HPT371 chips physically have only one channel, the secondary one, | |
1441 | * but the primary channel registers do exist! Go figure... | |
1442 | * So, we manually disable the non-existing channel here | |
1443 | * (if the BIOS hasn't done this already). | |
1444 | */ | |
1445 | pci_read_config_byte(dev, 0x50, &mcr1); | |
1446 | if (mcr1 & 0x04) | |
90778574 SS |
1447 | pci_write_config_byte(dev, 0x50, mcr1 & ~0x04); |
1448 | ||
7b73ee05 SS |
1449 | pci_set_drvdata(dev, info); |
1450 | ||
90778574 SS |
1451 | return ide_setup_pci_device(dev, d); |
1452 | } | |
1453 | ||
1454 | static int __devinit init_setup_hpt372a(struct pci_dev *dev, ide_pci_device_t *d) | |
1455 | { | |
7b73ee05 | 1456 | struct hpt_info *info; |
90778574 SS |
1457 | u8 rev = 0; |
1458 | ||
1459 | pci_read_config_byte(dev, PCI_REVISION_ID, &rev); | |
1460 | ||
7b73ee05 | 1461 | if (rev > 1) { |
90778574 SS |
1462 | d->name = "HPT372N"; |
1463 | ||
7b73ee05 SS |
1464 | info = &hpt372n; |
1465 | } else | |
1466 | info = &hpt372a; | |
1467 | pci_set_drvdata(dev, info); | |
1468 | ||
90778574 SS |
1469 | return ide_setup_pci_device(dev, d); |
1470 | } | |
1471 | ||
1472 | static int __devinit init_setup_hpt302(struct pci_dev *dev, ide_pci_device_t *d) | |
1473 | { | |
7b73ee05 | 1474 | struct hpt_info *info; |
90778574 SS |
1475 | u8 rev = 0; |
1476 | ||
1477 | pci_read_config_byte(dev, PCI_REVISION_ID, &rev); | |
1478 | ||
7b73ee05 | 1479 | if (rev > 1) { |
90778574 | 1480 | d->name = "HPT302N"; |
836c0063 | 1481 | |
7b73ee05 SS |
1482 | info = &hpt302n; |
1483 | } else | |
1484 | info = &hpt302; | |
1485 | pci_set_drvdata(dev, info); | |
1486 | ||
836c0063 SS |
1487 | return ide_setup_pci_device(dev, d); |
1488 | } | |
1489 | ||
1da177e4 LT |
1490 | static int __devinit init_setup_hpt366(struct pci_dev *dev, ide_pci_device_t *d) |
1491 | { | |
b4586715 SS |
1492 | struct pci_dev *dev2; |
1493 | u8 rev = 0; | |
90778574 SS |
1494 | static char *chipset_names[] = { "HPT366", "HPT366", "HPT368", |
1495 | "HPT370", "HPT370A", "HPT372", | |
1496 | "HPT372N" }; | |
7b73ee05 SS |
1497 | static struct hpt_info *info[] = { &hpt36x, &hpt36x, &hpt36x, |
1498 | &hpt370, &hpt370a, &hpt372, | |
1499 | &hpt372n }; | |
1da177e4 LT |
1500 | |
1501 | if (PCI_FUNC(dev->devfn) & 1) | |
1502 | return -ENODEV; | |
1503 | ||
e139b0b0 | 1504 | pci_read_config_byte(dev, PCI_REVISION_ID, &rev); |
1da177e4 | 1505 | |
90778574 | 1506 | if (rev > 6) |
e139b0b0 | 1507 | rev = 6; |
1da177e4 | 1508 | |
90778574 | 1509 | d->name = chipset_names[rev]; |
1da177e4 | 1510 | |
7b73ee05 SS |
1511 | pci_set_drvdata(dev, info[rev]); |
1512 | ||
90778574 SS |
1513 | if (rev > 2) |
1514 | goto init_single; | |
1da177e4 | 1515 | |
fdb0d72b | 1516 | /* |
96dcc08b SS |
1517 | * HPT36x chips have one channel per function and have |
1518 | * both channel enable bits located differently and visible | |
1519 | * to both functions -- really stupid design decision... :-( | |
1520 | * Bit 4 is for the primary channel, bit 5 for the secondary. | |
fdb0d72b | 1521 | */ |
1da177e4 | 1522 | d->channels = 1; |
96dcc08b | 1523 | d->enablebits[0].mask = d->enablebits[0].val = 0x10; |
1da177e4 | 1524 | |
b4586715 | 1525 | if ((dev2 = pci_get_slot(dev->bus, dev->devfn + 1)) != NULL) { |
96dcc08b | 1526 | u8 mcr1 = 0, pin1 = 0, pin2 = 0; |
b4586715 SS |
1527 | int ret; |
1528 | ||
7b73ee05 SS |
1529 | pci_set_drvdata(dev2, info[rev]); |
1530 | ||
96dcc08b SS |
1531 | /* |
1532 | * Now we'll have to force both channels enabled if | |
1533 | * at least one of them has been enabled by BIOS... | |
1534 | */ | |
1535 | pci_read_config_byte(dev, 0x50, &mcr1); | |
1536 | if (mcr1 & 0x30) | |
1537 | pci_write_config_byte(dev, 0x50, mcr1 | 0x30); | |
1538 | ||
b4586715 SS |
1539 | pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin1); |
1540 | pci_read_config_byte(dev2, PCI_INTERRUPT_PIN, &pin2); | |
1541 | if (pin1 != pin2 && dev->irq == dev2->irq) { | |
1542 | d->bootable = ON_BOARD; | |
1543 | printk("%s: onboard version of chipset, pin1=%d pin2=%d\n", | |
1544 | d->name, pin1, pin2); | |
1da177e4 | 1545 | } |
b4586715 SS |
1546 | ret = ide_setup_pci_devices(dev, dev2, d); |
1547 | if (ret < 0) | |
1548 | pci_dev_put(dev2); | |
1549 | return ret; | |
1da177e4 LT |
1550 | } |
1551 | init_single: | |
1552 | return ide_setup_pci_device(dev, d); | |
1553 | } | |
1554 | ||
1555 | static ide_pci_device_t hpt366_chipsets[] __devinitdata = { | |
1556 | { /* 0 */ | |
1557 | .name = "HPT366", | |
1558 | .init_setup = init_setup_hpt366, | |
1559 | .init_chipset = init_chipset_hpt366, | |
1560 | .init_hwif = init_hwif_hpt366, | |
1561 | .init_dma = init_dma_hpt366, | |
1562 | .channels = 2, | |
1563 | .autodma = AUTODMA, | |
7b73ee05 | 1564 | .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}}, |
1da177e4 LT |
1565 | .bootable = OFF_BOARD, |
1566 | .extra = 240 | |
1567 | },{ /* 1 */ | |
1568 | .name = "HPT372A", | |
90778574 | 1569 | .init_setup = init_setup_hpt372a, |
1da177e4 LT |
1570 | .init_chipset = init_chipset_hpt366, |
1571 | .init_hwif = init_hwif_hpt366, | |
1572 | .init_dma = init_dma_hpt366, | |
1573 | .channels = 2, | |
1574 | .autodma = AUTODMA, | |
7b73ee05 | 1575 | .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}}, |
1da177e4 | 1576 | .bootable = OFF_BOARD, |
90778574 | 1577 | .extra = 240 |
1da177e4 LT |
1578 | },{ /* 2 */ |
1579 | .name = "HPT302", | |
90778574 | 1580 | .init_setup = init_setup_hpt302, |
1da177e4 LT |
1581 | .init_chipset = init_chipset_hpt366, |
1582 | .init_hwif = init_hwif_hpt366, | |
1583 | .init_dma = init_dma_hpt366, | |
1584 | .channels = 2, | |
1585 | .autodma = AUTODMA, | |
7b73ee05 | 1586 | .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}}, |
1da177e4 | 1587 | .bootable = OFF_BOARD, |
90778574 | 1588 | .extra = 240 |
1da177e4 LT |
1589 | },{ /* 3 */ |
1590 | .name = "HPT371", | |
836c0063 | 1591 | .init_setup = init_setup_hpt371, |
1da177e4 LT |
1592 | .init_chipset = init_chipset_hpt366, |
1593 | .init_hwif = init_hwif_hpt366, | |
1594 | .init_dma = init_dma_hpt366, | |
1595 | .channels = 2, | |
1596 | .autodma = AUTODMA, | |
836c0063 | 1597 | .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}}, |
1da177e4 | 1598 | .bootable = OFF_BOARD, |
90778574 | 1599 | .extra = 240 |
1da177e4 LT |
1600 | },{ /* 4 */ |
1601 | .name = "HPT374", | |
1602 | .init_setup = init_setup_hpt374, | |
1603 | .init_chipset = init_chipset_hpt366, | |
1604 | .init_hwif = init_hwif_hpt366, | |
1605 | .init_dma = init_dma_hpt366, | |
1606 | .channels = 2, /* 4 */ | |
1607 | .autodma = AUTODMA, | |
7b73ee05 | 1608 | .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}}, |
1da177e4 | 1609 | .bootable = OFF_BOARD, |
90778574 | 1610 | .extra = 240 |
1da177e4 LT |
1611 | },{ /* 5 */ |
1612 | .name = "HPT372N", | |
90778574 | 1613 | .init_setup = init_setup_hpt372n, |
1da177e4 LT |
1614 | .init_chipset = init_chipset_hpt366, |
1615 | .init_hwif = init_hwif_hpt366, | |
1616 | .init_dma = init_dma_hpt366, | |
1617 | .channels = 2, /* 4 */ | |
1618 | .autodma = AUTODMA, | |
7b73ee05 | 1619 | .enablebits = {{0x50,0x04,0x04}, {0x54,0x04,0x04}}, |
1da177e4 | 1620 | .bootable = OFF_BOARD, |
90778574 | 1621 | .extra = 240 |
1da177e4 LT |
1622 | } |
1623 | }; | |
1624 | ||
1625 | /** | |
1626 | * hpt366_init_one - called when an HPT366 is found | |
1627 | * @dev: the hpt366 device | |
1628 | * @id: the matching pci id | |
1629 | * | |
1630 | * Called when the PCI registration layer (or the IDE initialization) | |
1631 | * finds a device matching our IDE device tables. | |
73d1dd93 SS |
1632 | * |
1633 | * NOTE: since we'll have to modify some fields of the ide_pci_device_t | |
1634 | * structure depending on the chip's revision, we'd better pass a local | |
1635 | * copy down the call chain... | |
1da177e4 | 1636 | */ |
1da177e4 LT |
1637 | static int __devinit hpt366_init_one(struct pci_dev *dev, const struct pci_device_id *id) |
1638 | { | |
73d1dd93 | 1639 | ide_pci_device_t d = hpt366_chipsets[id->driver_data]; |
1da177e4 | 1640 | |
73d1dd93 | 1641 | return d.init_setup(dev, &d); |
1da177e4 LT |
1642 | } |
1643 | ||
1644 | static struct pci_device_id hpt366_pci_tbl[] = { | |
1645 | { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, | |
1646 | { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1}, | |
1647 | { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2}, | |
1648 | { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3}, | |
1649 | { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4}, | |
1650 | { PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5}, | |
1651 | { 0, }, | |
1652 | }; | |
1653 | MODULE_DEVICE_TABLE(pci, hpt366_pci_tbl); | |
1654 | ||
1655 | static struct pci_driver driver = { | |
1656 | .name = "HPT366_IDE", | |
1657 | .id_table = hpt366_pci_tbl, | |
1658 | .probe = hpt366_init_one, | |
1659 | }; | |
1660 | ||
82ab1eec | 1661 | static int __init hpt366_ide_init(void) |
1da177e4 LT |
1662 | { |
1663 | return ide_pci_register_driver(&driver); | |
1664 | } | |
1665 | ||
1666 | module_init(hpt366_ide_init); | |
1667 | ||
1668 | MODULE_AUTHOR("Andre Hedrick"); | |
1669 | MODULE_DESCRIPTION("PCI driver module for Highpoint HPT366 IDE"); | |
1670 | MODULE_LICENSE("GPL"); |